+commit d62f64cc23a940eafe712c776b3249e4160753d1
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed May 16 00:13:33 2007 +0200
+
+ Coding Style Cleanup, new CHANGELOG
+
+commit 7d98ba770a7eaefa29ce927f31a0956df85bf650
+Author: Piotr Kruszynski <ppk@semihalf.com>
+Date: Thu May 10 16:55:52 2007 +0200
+
+ [Motion-PRO] Add MTD and JFFS2 support, also add default partition
+ definition.
+
+commit e69f66c6ebe82bbbd1da766bc4eda40ec7ee5af1
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue May 8 15:57:43 2007 +0200
+
+ add: reading special purpose registers
+
+commit 1a50f164beb065f360fbddb76029607d6b099698
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue May 8 14:52:52 2007 +0200
+
+ add: Microblaze V5 exception handling
+
+commit ab874d5047e5d30dbc1e517ff26083efffa98ecb
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue May 8 14:39:11 2007 +0200
+
+ add: FSL control read and write
+
+commit de1de02a7cbf05e6b63e0d8ffc624f12493f6ba3
+Author: Piotr Kruszynski <ppk@semihalf.com>
+Date: Tue May 8 13:05:44 2007 +0200
+
+ [Motion-PRO] Add support for I2C, EEPROM and RTC.
+
+commit fa5c2ba123b1bf88455bfc21db5e786ca045029d
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Tue May 8 10:23:56 2007 +0200
+
+ [Motion-PRO] Add ATA support. Add CF-booting commands to the default
+ environment.
+
+commit 06241d50a3ab1b20a0b08baeeaffcaa23ae4b839
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Tue May 8 09:39:12 2007 +0200
+
+ [Motion-PRO] Change IPB clock frequency from 50MHz to 100MHz. This
+ eliminates networking problems in Linux (timeouts).
+
+commit 1f1369c34b629be94702684d41d3fddf0f6193e7
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Tue May 8 09:21:57 2007 +0200
+
+ [Motion-PRO] Enable Flat Device Tree support and modify default environment
+ to allow booting of FDT-expecting kernels.
+
+commit fb05f6da35ea1c15c553abe6f23f656bf18dc5db
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 23:58:31 2007 +0200
+
+ new: USE_MSR_INTR support
+
+commit 008861a2f3ef2c062744d733787c7e530a1b8761
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Mon May 7 22:36:15 2007 +0200
+
+ [MPC5xxx] There are networking problems on the Motion-PRO board with
+ current PHY initalization code (tftp timeouts all the time). This commit
+ temporarily disables PHY initalization sequence to make the networking
+ operational, until a fix is found.
+
+commit abca901869c3760b6c5fecb825db6c1d91a78a93
+Author: Wolfgang Denk <wd@denx.de>
+Date: Mon May 7 22:10:36 2007 +0200
+
+ Get rid of duplicated file (see include/configs/sbc8560.h instead)
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 207b7b2c9d9752e0f6478c30c29b7087f6e6cbb6
+Author: Wolfgang Denk <wd@denx.de>
+Date: Mon May 7 22:07:08 2007 +0200
+
+ Get rid of duplicated file (see doc/README.SBC8560 instead)
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit a7bac7e9b57ba948051beb19ec5be3a75ce75383
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:43:10 2007 +0200
+
+ fix: read and write MSR - repair number of parameters
+
+commit 19bf1fbad7f19d5a120be9b1daf136e052fcab39
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:33:51 2007 +0200
+
+ new: fsl interrupt support
+ FSL_Has_data is connected to INTC.
+
+commit 792032baa7d625e34c981ab6df521911bd8dc861
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:30:12 2007 +0200
+
+ fix: interrupt handler
+ remove asm code
+
+commit f3f001a341ef185d0f13841be5b5dc3395aacc31
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:25:08 2007 +0200
+
+ fix: remove asm code
+
+commit fb7c2dbef02c9f6f8d7b04ec4c2bfb91418b9c01
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:12:43 2007 +0200
+
+ fix: clean interrupt
+
+commit 42efed6130c8fcf7da881385b5427065d2801757
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 17:22:25 2007 +0200
+
+ fix: interrupt handler for multiple sources
+
+commit 48fbd3a4cdabbebc1debd7eed73c00c2caf914f6
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 17:11:09 2007 +0200
+
+ new: add writing to msr register
+
+commit ac4cd59d59c9bf3f89cb7a344abf8184d678f562
+Author: Timur Tabi <timur@freescale.com>
+Date: Sat May 5 08:12:30 2007 +0200
+
+ 5xxx: write MAC address to mac-address and local-mac-address
+
+ Some device trees have a mac-address property, some have local-mac-address,
+ and some have both. To support all of these device trees, ftp_cpu_setup()
+ should write the MAC address to mac-address and local-mac-address, if they
+ exist.
+
+ Signed-off-by: Timur Tabi <timur@freescale.com>
+ Acked-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit a9d87e2707dcb249f6bb7f7ff7e00acd8cda9fd2
+Author: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
+Date: Sun Apr 29 14:01:54 2007 +0200
+
+ [PATCH] Use PVR to distinguish MPC5200B from MPC5200 in boot message
+
+ MPC5200B systems are incorrectly reported as MPC5200 in U-Boot start-up
+ message. Use PVR to distinguish between the two variants, and print proper CPU
+ information.
+
+ Signed-off-by: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
+ Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 4ec5bd55ed1ffa91a774af298769621f4fbb18c1
+Author: Ladislav Michl <ladis@linux-mips.org>
+Date: Wed Apr 25 16:01:26 2007 +0200
+
+ [PATCH] simplify silent console
+
+ Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit b7598a43f2b421a713d8135e98a42c37d9eb9df0
+Author: Sergei Shtylyov <sshtylyov@ru.mvista.com>
+Date: Mon Apr 23 15:30:39 2007 +0200
+
+ [PATCH] Avoid assigning PCI resources from zero address
+
+ If a PCI IDE card happens to get a zero address assigned to it, the Linux IDE
+ core complains and IDE drivers fails to work. Also, assigning zero to a BAR
+ was illegal according to PCI 2.1 (the later revisions seem to have excluded the
+ sentence about "0" being considered an invalid address) -- so, use a reasonable
+ starting value of 0x1000 (that's what the most Linux archs are using).
+
+ Alternatively, one might have fixed the calls to pci_set_region() individually
+ (some code even seems to have taken care of this issue) but that would have
+ been a lot more work. :-)
+
+ Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit 9ffd451afeb08e5be7ddae680487ec962b2bca25
+Author: Jeffrey Mann <mannj@embeddedplanet.com>
+Date: Mon Apr 23 14:00:11 2007 +0200
+
+ [patch] setenv(...) can delete environmentalvariables
+
+ update setenv() function so that entering a NULL value for the
+ variable's value will delete the environmental variable
+
+ Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit ebd0a0ae05a44769c4e27458ad4e9f3438250443
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Mon Apr 23 13:54:24 2007 +0200
+
+ [patch] use unsigned char in smc91111 driver for mac
+
+ the v_mac variable in the smc91111 driver is declared as a signed char ...
+ this causes problems when one of the bytes in the MAC is "signed" like 0xE0
+ because when it gets printed out, you get a display like:
+ 0xFFFFFFE0 and that's no good
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit ffc50f9bb194343c6303517a517708457a5eb6b8
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat May 5 18:54:42 2007 +0200
+
+ new: FSL and MSR support #2
+
+commit f7e2e0eb0668136305f78bb9c21be79b48a34247
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat May 5 18:27:16 2007 +0200
+
+ new: FSL and MSR support
+
+commit 2f15278c2eb911c668b4fe562130b78cf554d139
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat May 5 18:23:11 2007 +0200
+
+ Coding stylke cleanup; update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 885ec89b648a899a2f32393fd3ffd9f7234c4402
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat May 5 18:05:02 2007 +0200
+
+ Add STX GP3 SSA board to MAKEALL script; update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 5499645b3fe17a548af9dfc479ca6e2455f179a2
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat May 5 17:15:50 2007 +0200
+
+ Make "file" command happy with some config.mk files; update CHANGELOG
+
+commit e3b8c78bc2489c27ae020986ef0eaca684866cef
+Author: Jeffrey Mann <mannj@embeddedplanet.com>
+Date: Sat May 5 08:32:14 2007 +0200
+
+ ppc4xx: Detect if the sysclk on Sequoia is 33 or 33.333 MHz
+
+ The AMCC Secquoia board has been changed in a new revision from using a
+ 33.000 MHz clock to a 33.333 MHz system clock. A bit in the CPLD
+ indicates the difference. This patch reads that bit and uses the correct
+ clock speed for the board. This code is backward compatable will all
+ prior boards. All prior boards will be read as 33.000.
+
+ Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit f544ff6656fca263ed1ebe39899b6d95da67c8b8
+Author: Stefan Roese <sr@denx.de>
+Date: Sat May 5 08:29:01 2007 +0200
+
+ ppc4xx: Sequoia: Remove cpu/ppc4xx/speed.c from NAND booting
+
+ Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
+ for the 4k NAND boot image so define bus_frequency to 133MHz here
+ which is save for the refresh counter setup.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit a79886590593ba1d667c840caa4940c61639f18f
+Author: Thomas Knobloch <knobloch@siemens.com>
+Date: Sat May 5 07:04:42 2007 +0200
+
+ NAND: Wrong calculation of page number in nand_block_bad()
+
+ In case that there is no memory based bad block table available the
+ function nand_block_checkbad() in drivers/mtd/nand/nand_base.c will call
+ nand_block_bad() directly. When parameter 'getchip' is set to zero,
+ nand_block_bad() will not right shift the offset to calculate the
+ correct page number.
+
+ Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 9877d7dcd1eebe61aa5d8b8ffe9c048ea426e6f6
+Author: Wolfgang Denk <wd@denx.de>
+Date: Fri May 4 10:02:33 2007 +0200
+
+ Fix initrd length corruption in bootm command.
+
+ When using FDT Images, the length of an inital ramdisk was
+ overwritten (bug introduced by commit 87a449c8, 22 Aug 2006).
+
+ Patches by Timur Tabi & Johns Daniel.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 068aab660bc3912b930be5540e6b3f3fd6ad3c96
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Thu May 3 19:43:52 2007 -0500
+
+ mpc83xx: fix trivial error in MAKEALL
+
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+
+commit c64a89d6ce8584b9fc64f4e85da9ecac3cfc2c2a
+Author: Wolfgang Denk <wd@denx.de>
+Date: Thu May 3 16:34:41 2007 +0200
+
+ Update board configuration for STX GP3SSA board:
+
+ Enable hush shell, environment in flash rather in EEPROM,
+ more user-friendly default environment, etc.
+ The simple EEPROM environment can be selected easily in the board
+ config file.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
commit 2c6fb199dc5756fc72f49d1f4de105e089049d65
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Apr 24 14:37:49 2007 +0200
Signed-off-by Dan Malek, <dan@embeddedalley.com>
+commit ffa621a0d12a1ccd81c936c567f8917a213787a8
+Author: Andy Fleming <afleming@freescale.com>
+Date: Sat Feb 24 01:08:13 2007 -0600
+
+ Cleaned up some 85xx PCI bugs
+
+ * Cleaned up the CDS PCI Config Tables and added NULL entries to
+ the end
+ * Fixed PCIe LAWBAR assignemt to use the cpu-relative address
+ * Fixed 85xx PCI code to assign powar region sizes based on the
+ config values (rather than hard-coding them)
+ * Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address
+
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit 6743105988fc44d5b0d30388c790607835aae7a6
+Author: Andy Fleming <afleming@freescale.com>
+Date: Mon Apr 23 02:54:25 2007 -0500
+
+ Add support for the 8568 MDS board
+
+ This included some changes to common files:
+ * Add 8568 processor SVR to various places
+ * Add support for setting the qe bus-frequency value in the dts
+ * Add the 8568MDS target to the Makefile
+
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit af1c2b84bf27c8565baddc82d1abb93700d10e2e
+Author: David Updegraff <dave@cray.com>
+Date: Fri Apr 20 14:34:48 2007 -0500
+
+ Add support for treating unknown PHYs as generic PHYs.
+
+ When bringing up u-boot on new boards, PHY support sometimes gets
+ neglected. Most PHYs don't really need any special support,
+ though. By adding a generic entry that always matches if nothing
+ else does, we can provide support for "unsupported" PHYs for the
+ tsec.
+
+ The generic PHY driver supports most PHYs, including gigabit.
+
+ Signed-off-by: David Updegraff <dave@cray.com>
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit a75af9bfd8fff0499efdbb90601cec5a2afef117
+Author: James Yang <James.Yang@freescale.com>
+Date: Wed Feb 7 15:28:04 2007 -0600
+
+ Conditionalize 8641 Rev1.0 MCM workarounds
+
+ Signed-off-by: James Yang <James.Yang@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit f64702b7fc8f8df39d31add770df6e372f9e9ce3
+Author: Timur Tabi <timur@freescale.com>
+Date: Mon Apr 30 13:59:50 2007 -0500
+
+ Fix memory initialization on MPC8349E-mITX
+
+ Define CFG_DDR_SDRAM_CLK_CNTL for the MPC8349E-mITX and MPC8349E-mITX-GP.
+ This allows ddr->sdram_clk_cntl to be properly initialized. This is necessary
+ on some ITX boards, notably those with a revision 3.1 CPU.
+
+ Also change spd_sdram() in cpu/mpc83xx/spd_sdram.c to not write anything into
+ ddr->sdram_clk_cntl if CFG_DDR_SDRAM_CLK_CNTL is not defined.
+
+ Signed-off-by: Timur Tabi <timur@freescale.com>
+ Acked-by: Michael Benedict <MBenedict@twacs.com>
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+
+commit 54b2d434ae9d01787936f34fe1759cf3d7624ae3
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Mon Apr 30 15:26:21 2007 -0500
+
+ mpc83xx: replace elaborate boottime verbosity with 'clocks' command
+
+ and fix CPU: to align with Board: display text.
+
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+
+commit c1ab82669d9525998c34e802a12cad662723f22a
+Author: James Yang <James.Yang@freescale.com>
+Date: Fri Mar 16 13:02:53 2007 -0500
+
+ Rewrote picos_to_clk() to avoid rounding errors.
+ Clarified that conversion is to DRAM clocks rather than platform clocks.
+ Made function static to spd_sdram.c.
+
+ Signed-off-by: James Yang <James.Yang@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 8b39501d28754e72726ce7fb02310e56dbdf116a
+Author: Stefan Roese <sr@denx.de>
+Date: Sun Apr 29 14:13:01 2007 +0200
+
+ ppc4xx: Bamboo: Use current NAND driver and *not* the legacy driver
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 5c5d3242935cf3543af01142627494434834cf98
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Wed Apr 25 12:34:38 2007 -0500
+
+ mpc83xx: minor fixups for 8313rdb introduction
+
+commit 144876a380f5756f57412caf74c1d6dc201dd796
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue Apr 24 23:01:02 2007 +0200
+
+ [PATCH] MTD partition support, JFFS2 support
+
+commit 37ed6cdd4159195bfad68d8a237f6adda8f482cb
+Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+Date: Tue Apr 24 14:03:45 2007 +0200
+
+ ppc4xx: setup 440EPx/GRx ZMII/RGMII bridge depending on PFC register content.
+
+ Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
+
+commit 66ed6cca3f340f7a8a06d9272ae2ef8e96f0273d
+Author: Andy Fleming <afleming@freescale.com>
+Date: Mon Apr 23 02:37:47 2007 -0500
+
+ Reworked 85xx speed detection code
+
+ Changed the code to read the registers and calculate the clock
+ rates, rather than using a "switch" statement.
+
+ Idea from Andrew Klossner <andrew@cesa.opbu.xerox.com>
+
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit 81f481ca708ed6a56bf9c410e3191dbad581c565
+Author: Andy Fleming <afleming@freescale.com>
+Date: Mon Apr 23 02:24:28 2007 -0500
+
+ Enable 8544 support
+
+ * Add support to the Makefile
+ * Add 8544 configuration support to the tsec driver
+ * Add 8544 SVR numbers to processor.h
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 0d8c3a2096eaff8d7de89d45e9af4d4b0d4868fe
+Author: Andy Fleming <afleming@freescale.com>
+Date: Fri Feb 23 17:12:25 2007 -0600
+
+ Support 1G size on 8548
+
+ e500v2 and newer cores support 1G page sizes.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit 45cef612cc601d2d1c890fbbd7cdc9609a189a46
+Author: Andy Fleming <afleming@freescale.com>
+Date: Fri Feb 23 17:11:16 2007 -0600
+
+ Changed BOOKE_PAGESZ_nGB to BOOKE_PAGESZ_nG
+
+ The other pagesz constants use one letter to specify order of
+ magnitude. Also change the one reference to it in mpc8548cds/init.S
+
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit 1f9a318cea14272edd10d63739e2d326c90f430e
+Author: Andy Fleming <afleming@freescale.com>
+Date: Fri Feb 23 16:28:46 2007 -0600
+
+ Only set ddrioovcr for 8548 rev1.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit 9343dbf85bc03033f2102d8e8543567c2c1ad2d2
+Author: Andy Fleming <afleming@freescale.com>
+Date: Sat Feb 24 01:16:45 2007 -0600
+
+ Tweak DDR ECC error counter
+
+ Enable single-bit error counter when memory was cleared by ddr controller.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Andy Fleming <afleming@freescale.com>
+
+commit 85e7c7a45e3dd9c7ce3e722352ba60f8df1a7a4b
+Author: Timur Tabi <timur@freescale.com>
+Date: Mon Feb 12 13:34:55 2007 -0600
+
+ 85xx: write MAC address to mac-address and local-mac-address
+
+ Some device trees have a mac-address property, some have local-mac-address,
+ and some have both. To support all of these device trees, ftp_cpu_setup()
+ should write the MAC address to mac-address and local-mac-address, if they
+ exist.
+
+ Signed-off-by: Timur Tabi <timur@freescale.com>
+
+commit 03b81b48eec0ad249ec97a4ae16c36fa2e014ff4
+Author: Andy Fleming <afleming@freescale.com>
+Date: Mon Apr 23 01:44:44 2007 -0500
+
+ Some 85xx cpu cleanups
+
+ * Cleaned up the TSR[WIS] clearing
+ * Cleaned up DMA initialization
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
+commit 151d5d992eab8c497b24c816c73dc1ad8bffb4eb
+Author: Andy Fleming <afleming@freescale.com>
+Date: Mon Apr 23 01:32:22 2007 -0500
+
+ Add cpu support for the 8544
+
+ Recognize new SVR values, and add a few register definitions
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+ Acked-by: Andy Fleming <afleming@freescale.com>
+
+commit 25d83d7f4ac65727182d8ddaf7ba42fa74cf65ae
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Wed Apr 11 16:51:02 2007 -0500
+
+ Add MPC8544DS basic port board files.
+
+ Add board port under new board/freescale directory
+ structure and reuse existing PIXIS FPGA support there.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 0cde4b00fc7393b89f379d83a9d436dcb1334bfa
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Wed Apr 11 16:50:57 2007 -0500
+
+ Add MPC8544DS main configuration file.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 362dd83077ac04c0296bca3e824ec2fb3d44d9d6
+Author: Sergei Shtylyov <sshtylyov@ru.mvista.com>
+Date: Wed Dec 27 22:07:15 2006 +0300
+
+ Fix PCI I/O space mapping on Freescale MPC85x0ADS
+
+ The PCI I/O space mapping for Freescale MPC8540ADS board was broken by commit
+ 52c7a68b8d587ebcf5a6b051b58b3d3ffa377ddc which failed to update the #define's
+ describing the local address window used for the PCI I/O space accesses -- fix
+ this and carry over the necessary changes into the MPC8560ADS code since the
+ PCI I/O space mapping was also broken for this board (by the earlier commit
+ 087454609e47295443af793a282cddcd91a5f49c). Add the comments clarifying how
+ the PCI I/O space must be mapped to all the MPC85xx board config. headers.
+
+ Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
+
+ board/mpc8540ads/init.S | 4 ++--
+ board/mpc8560ads/init.S | 4 ++--
+ include/configs/MPC8540ADS.h | 5 ++---
+ include/configs/MPC8541CDS.h | 2 +-
+ include/configs/MPC8548CDS.h | 2 +-
+ include/configs/MPC8560ADS.h | 8 ++++----
+ 6 files changed, 12 insertions(+), 13 deletions(-)
+
+commit 96629cbabdb727d4a5e62542deefc01d498db6dc
+Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
+Date: Tue Dec 5 16:42:30 2006 +0800
+
+ u-boot: Fix e500 v2 core reset bug
+
+ The following patch fixes the e500 v2 core reset bug.
+ For e500 v2 core, a new reset control register is added to reset the
+ processor.
+
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 63247a5acd58032e6cf33f525bc3923b467bac88
+Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
+Date: Wed Dec 20 11:01:00 2006 +0800
+
+ u-boot: v2: Remove the fixed TLB and LAW entrynubmer
+
+ Remove the fixed TLB and LAW entry nubmer. Use actually TLB and LAW
+ entry number to control the loop. This can reduce the potential risk
+ for the 85xx processor increasing its TLB adn LAW entry number.
+
+ Signed-off-by: Swarthout Edward <swarthout@freescale.com>
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 0b1934ba12fd408fcc3b8bd9f4b04864c42a42bf
+Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
+Date: Mon Dec 18 17:01:04 2006 +0800
+
+ u-boot: Fix the 85xxcds tsec bug
+
+ Fix the 85xxcds tsec bug.
+ When enable PCI, tsec.o should be added to u-boot.lds to make tsec work.
+
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 7337b237ffc4aaf1b9467024fe472a880d852598
+Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
+Date: Fri Dec 15 14:43:31 2006 +0800
+
+ u-boot: Fix CPU2 errata on MPC8548CDS board
+
+ This patch apply workaround of CPU2 errata on MPC8548CDS board.
+
+ Signed-off-by:Ebony Zhu <ebony.zhu@freescale.com>
+
+commit 39b18c4f3e0b6d0dc00f4e68bad2da3766c85f09
+Author: ebony.zhu@freescale.com <ebony.zhu@freescale.com>
+Date: Mon Dec 18 16:25:15 2006 +0800
+
+ u-boot: Disables MPC8548CDS 2T_TIMING for DDR by default
+
+ This patch disables MPC8548CDS 2T_TIMING for DDR by default.
+
+ Signed-off-by:Ebony Zhu <ebony.zhu@freescale.com>
+
+commit 41fb7e0f1ec9b91bdae2565bab5f2e3ee15039c7
+Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
+Date: Thu Dec 14 14:14:55 2006 +0800
+
+ u-boot: Enable PCI function and add PEX & rapidio memory map on MPC8548CDS board
+
+ Enable PCI function and add PEX & rapidio memory map on MPC8548CDS
+ board.
+ Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+
+commit 96b8a05432f346f36493535c85320b70ec9c7c1b
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:54:15 2007 -0500
+
+ mpc83xx: Add MPC8313ERDB support.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 49ea3b6eafe606285ae4d5c378026153dde53200
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:21 2007 -0500
+
+ mpc83xx: Add generic PCI setup code.
+
+ Board code can now request the generic setup code rather than having to
+ copy-and-paste it for themselves. Boards should be converted to use this
+ once they're tested with it.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 7c98e5193e93df6b9b651851d54b638a61ebb0ea
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:19 2007 -0500
+
+ mpc83xx: Add 831x support to speed.c.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 0f253283a32d91e06844d7f87f9b33f4f4fbce8f
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:18 2007 -0500
+
+ mpc83xx: Add 831x support to global_data.h
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 95e7ef897e54591e615fc1b458b74c286fe1fb06
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:16 2007 -0500
+
+ mpc83xx: Change PVR_83xx to PVR_E300C1-3, and update checkcpu().
+
+ Rather than misleadingly define PVR_83xx as the specific type of 83xx
+ being built for, the PVR of each core revision is defined. checkcpu() now
+ prints the core that it detects, rather than aborting if it doesn't find
+ what it thinks it wants.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit a35b0c4950d84cf9e3a9e32b916135956d1ac636
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:15 2007 -0500
+
+ mpc83xx: Recognize SPR values for MPC8311 and MPC8313.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit d87c57b201b4572d16f1b642998faa00c9912b16
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:31:55 2007 -0500
+
+ mpc83xx: Add register definitions for MPC831x.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 323bfa8f436dc3bc57187c9b1488bc3146ff1522
+Author: Stefan Roese <sr@denx.de>
+Date: Mon Apr 23 12:00:22 2007 +0200
+
+ Remove BOARDLIBS usage completely
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
+commit 32556443840f127170e4baa8bdd5b567039f6c36
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat Apr 21 21:07:22 2007 +0200
+
+ [PATCH] SystemACE support for Microblaze
+
+commit 0643631aa1036cd746bf5d15f5a34bc7bc01ea4f
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat Apr 21 21:02:40 2007 +0200
+
+ 16bit read/write little endian
+
+commit 9d1d6a34d26c5933bc097ce73c9348f95573cdd4
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat Apr 21 20:53:31 2007 +0200
+
+ Change ML401 parameters - Xilinx BSP
+
+commit 2e343b9a57f32e1bd08c35c9976910333fb4e13d
+Author: Ed Swarthout <Ed.Swarthout@freescale.com>
+Date: Wed Feb 28 05:37:29 2007 -0600
+
+ mpc8641hpcn: Fix LAW and TLB setup to use the IO_PHYS #defines.
+
+ Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
+
+commit 79cb47391eebef85acadb3f6961ef6c55cace6ac
+Author: Zhang Wei <wei.zhang@freescale.com>
+Date: Fri Jan 19 10:42:37 2007 +0800
+
+ Enable LAWs for MPC8641 PCI-Ex2.
+
+ Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit bd7851ce1e1f140665b520026abf1042968b1102
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Fri Apr 20 14:12:26 2007 -0500
+
+ mpc86xx; Write MAC address to mac-address and local-mac-address
+
+ Some device trees have a mac-address property, some have local-mac-address,
+ and some have both. To support all of these device trees, ftp_cpu_setup()
+ should write the MAC address to mac-address and local-mac-address, if they
+ exist.
+
+ Signed-off-by: Timur Tabi <timur@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
+commit 7dbdf28b8bd855a8530dc3292e4982575a197060
+Author: Jon Loeliger <jdl@freescale.com>
+Date: Fri Apr 20 14:11:38 2007 -0500
+
+ mpc86xx: protect memcpy to bad address if a mac-address is missing from dt
+
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+ Signed-off-by: Jon Loeliger <jdl@freescale.com>
+
commit 14da5f7675bbb427c469e3f45006e027b6e21db9
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Apr 20 17:43:28 2007 +0200
Also moved the libfdt.a requirement into the main Makefile. That is
The U-Boot Way.
+commit d21686263574e95cb3e9e9b0496f968b1b897fdb
+Author: Stefan Roese <sr@denx.de>
+Date: Thu Apr 19 09:53:52 2007 +0200
+
+ ppc4xx: Fix chip select timing for SysACE access on AMCC Katmai
+
+ Previous versions used full wait states for the chip select #1 which
+ is connected to the Xilinix SystemACE controller on the AMCC Katmai
+ evaluation board. This leads to really slow access and therefore low
+ performance. This patch now sets up the chip select a lot faster
+ resulting in much better read/write performance of the Linux driver.
+
+ Signed-off-by: Stefan Roese <sr@denx.de>
+
commit 37837828d89084879bee2f2b8c7c68d4695940df
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 18 17:49:29 2007 +0200
Signed-of-by: Greg Lopp <lopp@pobox.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
+commit 6fbf261f8df294e589cfadebebe5468e3c0f29e9
+Author: Xie Xiaobo <r63061@freescale.com>
+Date: Fri Mar 9 19:08:25 2007 +0800
+
+ Fix two bugs for MPC83xx DDR2 controller SPD Init
+
+ There are a few bugs in the cpu/mpc83xx/spd_sdram.c
+ the first bug is that the picos_to_clk routine introduces a huge
+ rounding error in 83xx.
+ the second bug is that the mode register write recovery field is
+ tWR-1, not tWR >> 1.
+
commit 2ad3aba01d37b72e7c957b07e102fccd64fe6d13
Author: Jeffrey Mann <mannj@embeddedplanet.com>
Date: Thu Apr 12 14:15:59 2007 +0200
#########################################################################
LIST_83xx=" \
- MPC832XEMDS MPC8349EMDS MPC8349ITX MPC8349ITXGP \
- MPC8360EMDS sbc8349 TQM834x \
+ MPC8313ERDB MPC832XEMDS MPC8349EMDS MPC8349ITX \
+ MPC8349ITXGP MPC8360EMDS sbc8349 TQM834x \
"
#########################################################################
LIST_85xx=" \
- MPC8540ADS MPC8540EVAL MPC8541CDS MPC8548CDS \
- MPC8555CDS MPC8560ADS PM854 PM856 \
- sbc8540 sbc8560 stxgp3 TQM8540 \
- TQM8541 TQM8555 TQM8560 \
+ MPC8540ADS MPC8540EVAL MPC8541CDS MPC8544DS \
+ MPC8548CDS MPC8555CDS MPC8560ADS PM854 \
+ PM856 sbc8540 sbc8560 stxgp3 \
+ stxssa TQM8540 TQM8541 TQM8555 \
+ TQM8560 \
"
#########################################################################
ifdef SOC
LIBS += cpu/$(CPU)/$(SOC)/lib$(SOC).a
endif
+ifeq ($(CPU),ixp)
+LIBS += cpu/ixp/npe/libnpe.a
+endif
LIBS += lib_$(ARCH)/lib$(ARCH).a
LIBS += fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a \
fs/reiserfs/libreiserfs.a fs/ext2/libext2fs.a
"post/board/$(BOARDDIR)/libpost$(BOARD).a"; fi)
LIBS += common/libcommon.a
LIBS += libfdt/libfdt.a
-LIBS += $(BOARDLIBS)
LIBS := $(addprefix $(obj),$(LIBS))
.PHONY : $(LIBS)
## MPC83xx Systems
#########################################################################
+MPC8313ERDB_33_config \
+MPC8313ERDB_66_config: unconfig
+ @echo "" >include/config.h ; \
+ if [ "$(findstring _33_,$@)" ] ; then \
+ echo -n "...33M ..." ; \
+ echo "#define CFG_33MHZ" >>include/config.h ; \
+ fi ; \
+ if [ "$(findstring _66_,$@)" ] ; then \
+ echo -n "...66M..." ; \
+ echo "#define CFG_66MHZ" >>include/config.h ; \
+ fi ;
+ @$(MKCONFIG) -a MPC8313ERDB ppc mpc83xx mpc8313erdb
+
MPC832XEMDS_config \
MPC832XEMDS_HOST_33_config \
MPC832XEMDS_HOST_66_config \
MPC8541CDS_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8541cds cds
+MPC8544DS_config: unconfig
+ @$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8544ds freescale
+
MPC8548CDS_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8548cds cds
MPC8555CDS_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8555cds cds
+MPC8568MDS_config: unconfig
+ @$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8568mds
+
PM854_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc85xx pm854
CFG_CMD_VFD * VFD support (TRAB)
CFG_CMD_BSP * Board SPecific functions
CFG_CMD_CDP * Cisco Discover Protocol support
+ CFG_CMD_FSL * Microblaze FSL support
-----------------------------------------------
CFG_CMD_ALL all
acadia_gpio_init();
+ /* Configure 405EZ for NAND usage */
+ mtsdr(sdrnand0, 0x80c00000);
+ mtsdr(sdrultra0, 0x8d110000);
+
/* USB Host core needs this bit set */
mfsdr(sdrultra1, reg);
mtsdr(sdrultra1, reg | SDR_ULTRA1_LEDNENABLE);
int checkboard(void)
{
char *s = getenv("serial#");
+ u8 rev;
+
+ rev = in8(CFG_CPLD_BASE + 0);
+ printf("Board: Acadia - AMCC PPC405EZ Evaluation Board, Rev. %X", rev);
- printf("Board: Acadia - AMCC PPC405EZ Evaluation Board");
if (s != NULL) {
puts(", serial# ");
puts(s);
return 0;
}
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-/*----------------------------------------------------------------------------+
- | nand_reset.
- | Reset Nand flash
- | This routine will abort previous cmd
- +----------------------------------------------------------------------------*/
-int nand_reset(ulong addr)
-{
- int wait=0, stat=0;
-
- out8(addr + NAND_CMD_REG, NAND0_CMD_RESET);
- out8(addr + NAND_CMD_REG, NAND0_CMD_READ_STATUS);
-
- while ((stat != 0xc0) && (wait != 0xffff)) {
- stat = in8(addr + NAND_DATA_REG);
- wait++;
- }
-
- if (stat == 0xc0) {
- return 0;
- } else {
- printf("NAND Reset timeout.\n");
- return -1;
- }
-}
-
-void board_nand_set_device(int cs, ulong addr)
-{
- /* Set NandFlash Core Configuration Register */
- out32(addr + NAND_CCR_REG, 0x00001000 | (cs << 24));
-
- switch (cs) {
- case 1:
- /* -------
- * NAND0
- * -------
- * K9F1208U0A : 4 addr cyc, 1 col + 3 Row
- * Set NDF1CR - Enable External CS1 in NAND FLASH controller
- */
- out32(addr + NAND_CR1_REG, 0x80002222);
- break;
-
- case 2:
- /* -------
- * NAND1
- * -------
- * K9K2G0B : 5 addr cyc, 2 col + 3 Row
- * Set NDF2CR : Enable External CS2 in NAND FLASH controller
- */
- out32(addr + NAND_CR2_REG, 0xC0007777);
- break;
- }
-
- /* Perform Reset Command */
- if (nand_reset(addr) != 0)
- return;
-}
-
-void nand_init(void)
-{
- board_nand_set_device(1, CFG_NAND_ADDR);
-
- nand_probe(CFG_NAND_ADDR);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-
-#if 0 /* NAND1 not supported yet */
- board_nand_set_device(2, CFG_NAND2_ADDR);
-
- nand_probe(CFG_NAND2_ADDR);
- if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
- print_size(nand_dev_desc[0].totlen, "\n");
- }
-#endif
-}
-#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */
-
int checkboard(void)
{
char *s = getenv("serial#");
cpu/ppc4xx/start.o (.text)
board/amcc/bamboo/init.o (.text)
- cpu/ppc4xx/kgdb.o (.text)
- cpu/ppc4xx/traps.o (.text)
- cpu/ppc4xx/interrupts.o (.text)
- cpu/ppc4xx/serial.o (.text)
- cpu/ppc4xx/cpu_init.o (.text)
- cpu/ppc4xx/speed.o (.text)
- common/dlmalloc.o (.text)
- lib_generic/crc32.o (.text)
- lib_ppc/extable.o (.text)
- lib_generic/zlib.o (.text)
-
-/* . = env_offset;*/
-/* common/environment.o(.text)*/
+ board/amcc/bamboo/bamboo.o (.text)
*(.text)
*(.fixup)
}
#endif /* CONFIG_DDR_DATA_EYE */
+#if defined(CONFIG_NAND_SPL)
+/* Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
+ * for the 4k NAND boot image so define bus_frequency to 133MHz here
+ * which is save for the refresh counter setup.
+ */
+#define get_bus_freq(val) 133000000
+#endif
+
/*************************************************************************
*
* initdram -- 440EPx's DDR controller is a DENALI Core
mtsdram(DDR0_22, 0x00267F0B);
mtsdram(DDR0_23, 0x00000000);
mtsdram(DDR0_24, 0x01010002);
- if (speed > 133333333)
+ if (speed > 133333334)
mtsdram(DDR0_26, 0x5B26050C);
else
mtsdram(DDR0_26, 0x5B260408);
(0x80000000 >> (28 + CFG_NAND_CS));
mtsdr(SDR0_CUST0, sdr0_cust0);
+ /* Update EBC speed after booting from i2c bootstrap settings
+ * on newer boards with 33.333 MHZ Clocks
+ */
+ if (in8(CFG_BCSR_BASE + 3) & 0x80)
+ mtcpr(0xe0, 0x02000000);
+
return 0;
}
printf("Board: Rainier - AMCC PPC440GRx Evaluation Board");
#endif
- rev = *(u8 *)(CFG_BCSR_BASE + 0);
- val = *(u8 *)(CFG_BCSR_BASE + 5) & 0x01;
+ rev = in8(CFG_BCSR_BASE + 0);
+ val = in8(CFG_BCSR_BASE + 5) & 0x01;
printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33);
if (s != NULL) {
static struct pci_config_table pci_mpc85xxcds_config_table[] = {
{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
{0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}},
- {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}},
+ {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1,
+ mpc85xx_config_via_usbide, {0,0,0}},
{0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}},
{0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}},
- {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}},
- {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}
+ {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5,
+ mpc85xx_config_via_power, {0,0,0}},
+ {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}},
+ {},
};
static struct pci_controller hose[] = {
cpu/mpc85xx/interrupts.o (.text)
cpu/mpc85xx/cpu_init.o (.text)
cpu/mpc85xx/cpu.o (.text)
+ drivers/tsec.o (.text)
cpu/mpc85xx/speed.o (.text)
cpu/mpc85xx/pci.o (.text)
common/dlmalloc.o (.text)
/*
* Number of TLB0 and TLB1 entries in the following table
*/
- .long 13
+ .long (2f-1f)/16
+1:
#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
/*
* TLB0 4K Non-cacheable, guarded
/*
* TLB 1: 256M Non-cacheable, guarded
- * 0x80000000 256M PCI1 MEM First half
+ * 0x80000000 256M PCI1 MEM
*/
.long TLB1_MAS0(1, 1, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
/*
* TLB 2: 256M Non-cacheable, guarded
- * 0x90000000 256M PCI1 MEM Second half
+ * 0x90000000 256M PCI2 MEM
*/
.long TLB1_MAS0(1, 2, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE),
0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE),
0,0,0,0,0,1,0,1,0,1)
/*
- * TLB 3: 256M Non-cacheable, guarded
- * 0xa0000000 256M PCI2 MEM First half
+ * TLB 3: 1GB Non-cacheable, guarded
+ * 0xa0000000 256M PEX MEM First half
+ * 0xb0000000 256M PEX MEM Second half
+ * 0xc0000000 256M Rapid IO MEM First half
+ * 0xd0000000 256M Rapid IO MEM Second half
*/
.long TLB1_MAS0(1, 3, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PEX_MEM_BASE), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PEX_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
/*
- * TLB 4: 256M Non-cacheable, guarded
- * 0xb0000000 256M PCI2 MEM Second half
+ * TLB 4: Reserved for future usage
*/
- .long TLB1_MAS0(1, 4, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000),
- 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000),
- 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 5: 64M Non-cacheable, guarded
* 0xe000_0000 1M CCSRBAR
- * 0xe200_0000 16M PCI1 IO
- * 0xe300_0000 16M PCI2 IO
+ * 0xe200_0000 8M PCI1 IO
+ * 0xe280_0000 8M PCI2 IO
+ * 0xe300_0000 16M PEX IO
*/
.long TLB1_MAS0(1, 5, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)
.long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1)
-
+2:
entry_end
/*
* LAW(Local Access Window) configuration:
*
* 0x0000_0000 0x7fff_ffff DDR 2G
- * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
- * 0xa000_0000 0xbfff_ffff PCI2 MEM 512M
+ * 0x8000_0000 0x8fff_ffff PCI1 MEM 256M
+ * 0x9000_0000 0x9fff_ffff PCI2 MEM 256M
+ * 0xa000_0000 0xbfff_ffff PEX MEM 512M
+ * 0xc000_0000 0xdfff_ffff RapidIO 512M
* 0xe000_0000 0xe000_ffff CCSR 1M
- * 0xe200_0000 0xe20f_ffff PCI1 IO 1M
- * 0xe210_0000 0xe21f_ffff PCI2 IO 1M
- * 0xf000_0000 0xf7ff_ffff SDRAM 128M
+ * 0xe200_0000 0xe27f_ffff PCI1 IO 8M
+ * 0xe280_0000 0xe2ff_ffff PCI2 IO 8M
+ * 0xe300_0000 0xe3ff_ffff PEX IO 16M
+ * 0xf000_0000 0xf3ff_ffff SDRAM 64M
* 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M
* 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M
* 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M
#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
-#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_256M))
#define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff)
-#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_256M))
#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
-#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_1M))
+#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_8M))
#define LAWBAR4 ((CFG_PCI2_IO_PHYS>>12) & 0xfffff)
-#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_1M))
+#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_8M))
/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
#define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
#define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+#define LAWBAR6 ((CFG_PEX_MEM_BASE>>12) & 0xfffff)
+#define LAWAR6 (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR7 ((CFG_PEX_IO_PHYS>>12) & 0xfffff)
+#define LAWAR7 (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+#define LAWBAR8 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
+#define LAWAR8 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
.section .bootpg, "ax"
.globl law_entry
law_entry:
entry_start
- .long 6
+ .long (4f-3f)/8
+3:
.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
- .long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5
+ .long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5,LAWBAR6,LAWAR6,LAWBAR7,LAWAR7
+ .long LAWBAR8,LAWAR8
+4:
entry_end
{
volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
volatile ccsr_gur_t *gur = &immap->im_gur;
+ volatile ccsr_local_ecm_t *ecm = &immap->im_local_ecm;
/* PCI slot in USER bits CSR[6:7] by convention. */
uint pci_slot = get_pci_slot ();
*/
local_bus_init ();
+ /*
+ * Fix CPU2 errata: A core hang possible while executing a
+ * msync instruction and a snoopable transaction from an I/O
+ * master tagged to make quick forward progress is present.
+ */
+ ecm->eebpcr |= (1 << 16);
/*
* Hack TSEC 3 and 4 IO voltages.
static struct pci_config_table pci_mpc85xxcds_config_table[] = {
{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
{0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}},
- {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}},
+ {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1,
+ mpc85xx_config_via_usbide, {0,0,0}},
{0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}},
{0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}},
- {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}},
- {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}
+ {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5,
+ mpc85xx_config_via_power, {0,0,0}},
+ {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}},
+ {},
};
static struct pci_controller hose[] = {
cpu/mpc85xx/interrupts.o (.text)
cpu/mpc85xx/cpu_init.o (.text)
cpu/mpc85xx/cpu.o (.text)
+ drivers/tsec.o (.text)
cpu/mpc85xx/speed.o (.text)
cpu/mpc85xx/pci.o (.text)
common/dlmalloc.o (.text)
static struct pci_config_table pci_mpc85xxcds_config_table[] = {
{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
{0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}},
- {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}},
+ {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1,
+ mpc85xx_config_via_usbide, {0,0,0}},
{0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}},
{0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}},
- {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}},
- {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}
+ {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5,
+ mpc85xx_config_via_power, {0,0,0}},
+ {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}},
+ {},
};
config_table: pci_mpc85xxcds_config_table,
},
#ifdef CONFIG_MPC85XX_PCI2
- { }
+ {},
#endif
};
cpu/mpc85xx/interrupts.o (.text)
cpu/mpc85xx/cpu_init.o (.text)
cpu/mpc85xx/cpu.o (.text)
+ drivers/tsec.o (.text)
cpu/mpc85xx/speed.o (.text)
cpu/mpc85xx/pci.o (.text)
common/dlmalloc.o (.text)
--- /dev/null
+#
+# Copyright 2007 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+# ifneq ($(OBJTREE),$(SRCTREE))
+# $(shell mkdir -p $(obj)./common)
+# endif
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o \
+ ../common/pixis.o
+
+SOBJS := init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) crv $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# Copyright 2007 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8544ds board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xfff80000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8544=1
--- /dev/null
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+#define LAWAR_TRGT_PCI1 0x00000000
+#define LAWAR_TRGT_PCIE1 0x00200000
+#define LAWAR_TRGT_PCIE2 0x00100000
+#define LAWAR_TRGT_PCIE3 0x00300000
+#define LAWAR_TRGT_LBC 0x00400000
+#define LAWAR_TRGT_DDR 0x00f00000
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+
+#define entry_start \
+ mflr r1 ; \
+ bl 0f ;
+
+#define entry_end \
+0: mflr r0 ; \
+ mtlr r1 ; \
+ blr ;
+
+
+ .section .bootpg, "ax"
+ .globl tlb1_entry
+tlb1_entry:
+ entry_start
+
+ /*
+ * Number of TLB0 and TLB1 entries in the following table
+ */
+ .long (2f-1f)/16
+1:
+ /*
+ * TLB0 4K Non-cacheable, guarded
+ * 0xff700000 4K Initial CCSRBAR mapping
+ *
+ * This ends up at a TLB0 Index==0 entry, and must not collide
+ * with other TLB0 Entries.
+ */
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB0 16K Cacheable, guarded
+ * Temporary Global data for initialization
+ *
+ * Use four 4K TLB0 entries. These entries must be cacheable
+ * as they provide the bootstrap memory before the memory
+ * controler and real memory have been configured.
+ *
+ * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+ * and must not collide with other TLB0 entries.
+ */
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
+ 0,0,0,0,0,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+ 0,0,0,0,0,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+ 0,0,0,0,0,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+ 0,0,0,0,0,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+
+ /*
+ * TLB 0: 64M Non-cacheable, guarded
+ * 0xfc000000 64M Covers FLASH at 0xFE800000 and 0xFF800000
+ * Out of reset this entry is only 4K.
+ */
+ .long TLB1_MAS0(1, 0, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 1: 1G Non-cacheable, guarded
+ * 0x80000000 1G PCIE 8,9,a,b
+ */
+ .long TLB1_MAS0(1, 1, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PCIE_PHYS),
+ 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PCIE_PHYS),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 2: 256M Non-cacheable, guarded
+ */
+ .long TLB1_MAS0(1, 2, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS),
+ 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 3: 256M Non-cacheable, guarded
+ */
+ .long TLB1_MAS0(1, 3, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS + 0x10000000),
+ 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS + 0x10000000),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLB 4: 64M Non-cacheable, guarded
+ * 0xe000_0000 1M CCSRBAR
+ * 0xe100_0000 255M PCI IO range
+ */
+ .long TLB1_MAS0(1, 4, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+#ifdef CFG_LBC_CACHE_BASE
+ /*
+ * TLB 5: 64M Cacheable, non-guarded
+ */
+ .long TLB1_MAS0(1, 5, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,1,0,1,0,1)
+#endif
+ /*
+ * TLB 6: 64M Non-cacheable, guarded
+ * 0xf8000000 64M PIXIS 0xF8000000 - 0xFBFFFFFF
+ */
+ .long TLB1_MAS0(1, 6, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,0,1,0,1,0,1)
+2:
+ entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ *
+ * Notes:
+ * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
+ *
+ * LAW 0 is reserved for boot mapping
+ */
+
+ .section .bootpg, "ax"
+ .globl law_entry
+law_entry:
+ entry_start
+
+ .long (4f-3f)/8
+3:
+ .long 0
+ .long (LAWAR_TRGT_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN
+
+ .long (CFG_PCI1_MEM_BASE>>12) & 0xfffff
+ .long LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M)
+
+ .long (CFG_PCI1_IO_PHYS>>12) & 0xfffff
+ .long LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M)
+
+ .long (CFG_LBC_CACHE_BASE>>12) & 0xfffff
+ .long LAWAR_EN | LAWAR_TRGT_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)
+
+ .long (CFG_PCIE1_MEM_PHYS>>12) & 0xfffff
+ .long LAWAR_EN | LAWAR_TRGT_PCIE1 | (LAWAR_SIZE & LAWAR_SIZE_256M)
+
+ /* To keep to 10 LAWs, PCIE1_IO_PHYS must use top of mem region */
+
+ .long (CFG_PCIE2_MEM_PHYS>>12) & 0xfffff
+ .long LAWAR_EN | LAWAR_TRGT_PCIE2 | (LAWAR_SIZE & LAWAR_SIZE_512M)
+
+ .long (CFG_PCIE2_IO_PHYS>>12) & 0xfffff
+ .long LAWAR_EN | LAWAR_TRGT_PCIE2 | (LAWAR_SIZE & LAWAR_SIZE_16M)
+
+ .long (CFG_PCIE3_MEM_PHYS>>12) & 0xfffff
+ .long LAWAR_EN | LAWAR_TRGT_PCIE3 | (LAWAR_SIZE & LAWAR_SIZE_256M)
+
+ .long (CFG_PCIE3_IO_PHYS>>12) & 0xfffff
+ .long LAWAR_EN | LAWAR_TRGT_PCIE3 | (LAWAR_SIZE & LAWAR_SIZE_16M)
+4:
+ entry_end
--- /dev/null
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <spd.h>
+#include <miiphy.h>
+
+#include "../common/pixis.h"
+
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+extern void ft_cpu_setup(void *blob, bd_t *bd);
+#endif
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void sdram_init(void);
+
+int board_early_init_f (void)
+{
+ return 0;
+}
+
+int checkboard (void)
+{
+ volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
+ volatile ccsr_gur_t *gur = &immap->im_gur;
+
+ if ((uint)&gur->porpllsr != 0xe00e0000) {
+ printf("immap size error %x\n",&gur->porpllsr);
+ }
+ printf ("Board: MPC8544DS\n");
+
+ return 0;
+}
+
+long int
+initdram(int board_type)
+{
+ long dram_size = 0;
+
+ puts("Initializing\n");
+
+ dram_size = spd_sdram();
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+ /*
+ * Initialize and enable DDR ECC.
+ */
+ ddr_enable_ecc(dram_size);
+#endif
+ puts(" DDR: ");
+ return dram_size;
+}
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+ uint *pstart = (uint *) CFG_MEMTEST_START;
+ uint *pend = (uint *) CFG_MEMTEST_END;
+ uint *p;
+
+ printf("Testing DRAM from 0x%08x to 0x%08x\n",
+ CFG_MEMTEST_START,
+ CFG_MEMTEST_END);
+
+ printf("DRAM test phase 1:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0xaaaaaaaa;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0xaaaaaaaa) {
+ printf ("DRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf("DRAM test phase 2:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0x55555555;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0x55555555) {
+ printf ("DRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf("DRAM test passed.\n");
+ return 0;
+}
+#endif
+
+int last_stage_init(void)
+{
+ return 0;
+}
+
+
+unsigned long
+get_board_sys_clk(ulong dummy)
+{
+ u8 i, go_bit, rd_clks;
+ ulong val = 0;
+
+ go_bit = in8(PIXIS_BASE + PIXIS_VCTL);
+ go_bit &= 0x01;
+
+ rd_clks = in8(PIXIS_BASE + PIXIS_VCFGEN0);
+ rd_clks &= 0x1C;
+
+ /*
+ * Only if both go bit and the SCLK bit in VCFGEN0 are set
+ * should we be using the AUX register. Remember, we also set the
+ * GO bit to boot from the alternate bank on the on-board flash
+ */
+
+ if (go_bit) {
+ if (rd_clks == 0x1c)
+ i = in8(PIXIS_BASE + PIXIS_AUX);
+ else
+ i = in8(PIXIS_BASE + PIXIS_SPD);
+ } else {
+ i = in8(PIXIS_BASE + PIXIS_SPD);
+ }
+
+ i &= 0x07;
+
+ switch (i) {
+ case 0:
+ val = 33333333;
+ break;
+ case 1:
+ val = 40000000;
+ break;
+ case 2:
+ val = 50000000;
+ break;
+ case 3:
+ val = 66666666;
+ break;
+ case 4:
+ val = 83000000;
+ break;
+ case 5:
+ val = 100000000;
+ break;
+ case 6:
+ val = 133333333;
+ break;
+ case 7:
+ val = 166666666;
+ break;
+ }
+
+ return val;
+}
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup(void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+
+ ft_cpu_setup(blob, bd);
+
+ p = ft_get_prop(blob, "/memory/reg", &len);
+ if (p != NULL) {
+ *p++ = cpu_to_be32(bd->bi_memstart);
+ *p = cpu_to_be32(bd->bi_memsize);
+ }
+}
+#endif
--- /dev/null
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+SECTIONS
+{
+ .resetvec 0xFFFFFFFC :
+ {
+ *(.resetvec)
+ } = 0xffff
+
+ .bootpg 0xFFFFF000 :
+ {
+ cpu/mpc85xx/start.o (.bootpg)
+ board/freescale/mpc8544ds/init.o (.bootpg)
+ } = 0xffff
+
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/mpc85xx/start.o (.text)
+ board/freescale/mpc8544ds/init.o (.text)
+ cpu/mpc85xx/traps.o (.text)
+ cpu/mpc85xx/interrupts.o (.text)
+ cpu/mpc85xx/cpu_init.o (.text)
+ cpu/mpc85xx/cpu.o (.text)
+ cpu/mpc85xx/speed.o (.text)
+ common/dlmalloc.o (.text)
+ lib_generic/crc32.o (.text)
+ lib_ppc/extable.o (.text)
+ lib_generic/zlib.o (.text)
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
+#
TEXT_BASE = 0x00f80000
-
-# include NPE ethernet driver
-BOARDLIBS = $(obj)cpu/ixp/npe/libnpe.a
#include <common.h>
#include <mpc5xxx.h>
+#include <miiphy.h>
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+#endif
+#if defined(CONFIG_STATUS_LED)
+#include <status_led.h>
+#endif /* CONFIG_STATUS_LED */
/* Kollmorgen DPR initialization data */
struct init_elem {
}
+/*
+ * Additional PHY intialization. After being reset in mpc5xxx_fec_init_phy(),
+ * PHY goes into FX mode. To take it out of the FX mode and switch into
+ * desired TX operation, one needs to clear the FX_SEL bit of Mode Control
+ * Register.
+ */
+void reset_phy(void)
+{
+ unsigned short mode_control;
+
+ miiphy_read("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15, &mode_control);
+ miiphy_write("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15,
+ mode_control & 0xfffe);
+ return;
+}
+
#ifndef CFG_RAMBOOT
/*
* Helper function to initialize SDRAM controller.
*/
-static void sdram_start (int hi_addr)
+static void sdram_start(int hi_addr)
{
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
/*
* Initalize SDRAM - configure SDRAM controller, detect memory size.
*/
-long int initdram (int board_type)
+long int initdram(int board_type)
{
ulong dramsize = 0;
#ifndef CFG_RAMBOOT
}
-int checkboard (void)
+int checkboard(void)
{
- puts("Board: Promess Motion-PRO board\n");
+ uchar rev = *(vu_char *)CPLD_REV_REGISTER;
+ printf("Board: Promess Motion-PRO board (CPLD rev. 0x%02x)\n", rev);
return 0;
}
+
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+}
+#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */
+
+
+#if defined(CONFIG_STATUS_LED)
+void __led_init(led_id_t regaddr, int state)
+{
+ *((vu_long *) regaddr) |= ENABLE_GPIO_OUT;
+
+ if (state == STATUS_LED_ON)
+ *((vu_long *) regaddr) |= LED_ON;
+ else
+ *((vu_long *) regaddr) &= ~LED_ON;
+}
+
+void __led_set(led_id_t regaddr, int state)
+{
+ if (state == STATUS_LED_ON)
+ *((vu_long *) regaddr) |= LED_ON;
+ else
+ *((vu_long *) regaddr) &= ~LED_ON;
+}
+
+void __led_toggle(led_id_t regaddr)
+{
+ *((vu_long *) regaddr) ^= LED_ON;
+}
+#endif /* CONFIG_STATUS_LED */
--- /dev/null
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) crv $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+TEXT_BASE = 0xFE000000
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ft_build.h>
+#include <pci.h>
+#include <mpc83xx.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+#ifndef CFG_8313ERDB_BROKEN_PMC
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ gd->flags |= GD_FLG_SILENT;
+#endif
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: Freescale MPC8313ERDB\n");
+ return 0;
+}
+
+static struct pci_region pci_regions[] = {
+ {
+ bus_start: CFG_PCI1_MEM_BASE,
+ phys_start: CFG_PCI1_MEM_PHYS,
+ size: CFG_PCI1_MEM_SIZE,
+ flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+ },
+ {
+ bus_start: CFG_PCI1_MMIO_BASE,
+ phys_start: CFG_PCI1_MMIO_PHYS,
+ size: CFG_PCI1_MMIO_SIZE,
+ flags: PCI_REGION_MEM
+ },
+ {
+ bus_start: CFG_PCI1_IO_BASE,
+ phys_start: CFG_PCI1_IO_PHYS,
+ size: CFG_PCI1_IO_SIZE,
+ flags: PCI_REGION_IO
+ }
+};
+
+void pci_init_board(void)
+{
+ volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+ volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+ volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+ struct pci_region *reg[] = { pci_regions };
+ int warmboot;
+
+ /* Enable all 3 PCI_CLK_OUTPUTs. */
+ clk->occr |= 0xe0000000;
+
+ /*
+ * Configure PCI Local Access Windows
+ */
+ pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR;
+ pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+ pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR;
+ pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+ warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+#ifndef CFG_8313ERDB_BROKEN_PMC
+ warmboot |= immr->pmc.pmccr1 & PMCCR1_POWER_OFF;
+#endif
+
+ mpc83xx_pci_init(1, reg, warmboot);
+}
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+
+#ifdef CONFIG_PCI
+ ft_pci_setup(blob, bd);
+#endif
+ ft_cpu_setup(blob, bd);
+
+ p = ft_get_prop(blob, "/memory/reg", &len);
+ if (p) {
+ *p++ = cpu_to_be32(bd->bi_memstart);
+ *p = cpu_to_be32(bd->bi_memsize);
+ }
+}
+#endif
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Authors: Nick.Spence@freescale.com
+ * Wilson.Lo@freescale.com
+ * scottwood@freescale.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+#ifndef CFG_8313ERDB_BROKEN_PMC
+static void resume_from_sleep(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ u32 magic = *(u32 *)0;
+
+ typedef void (*func_t)(void);
+ func_t resume = *(func_t *)4;
+
+ if (magic == 0xf5153ae5)
+ resume();
+
+ gd->flags &= ~GD_FLG_SILENT;
+ puts("\nResume from sleep failed: bad magic word\n");
+}
+#endif
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ volatile immap_t *im = (volatile immap_t *)CFG_IMMR;
+ u32 msize = CFG_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12;
+ im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
+ im->sysconf.ddrcdr = CFG_DDRCDR_VALUE;
+
+ /*
+ * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+ * or the DDR2 controller may fail to initialize correctly.
+ */
+ udelay(50000);
+
+ im->ddr.csbnds[0].csbnds = (msize - 1) >> 24;
+ im->ddr.cs_config[0] = CFG_DDR_CONFIG;
+
+ /* Currently we use only one CS, so disable the other bank. */
+ im->ddr.cs_config[1] = 0;
+
+ im->ddr.sdram_clk_cntl = CFG_DDR_CLK_CNTL;
+ im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3;
+ im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
+ im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
+ im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0;
+
+#ifndef CFG_8313ERDB_BROKEN_PMC
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ im->ddr.sdram_cfg = CFG_SDRAM_CFG | SDRAM_CFG_BI;
+ else
+#endif
+ im->ddr.sdram_cfg = CFG_SDRAM_CFG;
+
+ im->ddr.sdram_cfg2 = CFG_SDRAM_CFG2;
+ im->ddr.sdram_mode = CFG_DDR_MODE;
+ im->ddr.sdram_mode2 = CFG_DDR_MODE_2;
+
+ im->ddr.sdram_interval = CFG_DDR_INTERVAL;
+ sync();
+
+ /* enable DDR controller */
+ im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+
+ return msize;
+}
+
+long int initdram(int board_type)
+{
+ volatile immap_t *im = (volatile immap_t *)CFG_IMMR;
+ volatile lbus83xx_t *lbc = &im->lbus;
+ u32 msize;
+
+ if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ puts("Initializing\n");
+
+ /* DDR SDRAM - Main SODIMM */
+ msize = fixed_sdram();
+
+ /* Local Bus setup lbcr and mrtpr */
+ lbc->lbcr = CFG_LBC_LBCR;
+ lbc->mrtpr = CFG_LBC_MRTPR;
+ sync();
+
+#ifndef CFG_8313ERDB_BROKEN_PMC
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ resume_from_sleep();
+#endif
+
+ puts(" DDR RAM: ");
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
--- /dev/null
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/mpc83xx/start.o (.text)
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ . = ALIGN(16);
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x0FFF) & 0xFFFFF000;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(4096);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(4096);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
+ENTRY(_start)
im->ddr.sdram_interval =
(0x0410 << SDRAM_INTERVAL_REFINT_SHIFT) | (0x0100 <<
SDRAM_INTERVAL_BSTOPRE_SHIFT);
- im->ddr.sdram_clk_cntl =
- DDR_SDRAM_CLK_CNTL_SS_EN | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05;
+ im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL;
udelay(200);
#define LAWBAR2 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
-#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
-#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
+#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_1M))
/*
* Rapid IO at 0xc000_0000 for 512 M
#define LAWBAR2 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
-#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
-#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
+#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_1M))
/*
* Rapid IO at 0xc000_0000 for 512 M
--- /dev/null
+#
+# Copyright 2004-2007 Freescale Semiconductor.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o \
+ bcsr.o \
+ ft_board.o
+
+SOBJS := init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal SIMEK <monstr@monstr.eu>
+ * Copyright 2007 Freescale Semiconductor.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* MA 02111-1307 USA
*/
- .text
- .globl microblaze_disable_interrupts
- .ent microblaze_disable_interrupts
- .align 2
-microblaze_disable_interrupts:
- #Make space on stack for a temporary
- addi r1, r1, -4
- #Save register r12
- swi r12, r1, 0
- #Read the MSR register
- mfs r12, rmsr
- #Clear the interrupt enable bit
- andi r12, r12, ~2
- #Save the MSR register
- mts rmsr, r12
- #Load register r12
- lwi r12, r1, 0
- #Return
- rtsd r15, 8
- #Update stack in the delay slot
- addi r1, r1, 4
- .end microblaze_disable_interrupts
+#include <common.h>
+#include "bcsr.h"
+
+void enable_8568mds_duart()
+{
+ volatile uint* duart_mux = (uint *)(CFG_CCSRBAR + 0xe0060);
+ volatile uint* devices = (uint *)(CFG_CCSRBAR + 0xe0070);
+ volatile u8 *bcsr = (u8 *)(CFG_BCSR);
+
+ *duart_mux = 0x80000000; /* Set the mux to Duart on PMUXCR */
+ *devices = 0; /* Enable all peripheral devices */
+ bcsr[5] |= 0x01; /* Enable Duart in BCSR*/
+}
+
+void enable_8568mds_flash_write()
+{
+ volatile u8 *bcsr = (u8 *)(CFG_BCSR);
+
+ bcsr[9] |= 0x01;
+}
+
+void disable_8568mds_flash_write()
+{
+ volatile u8 *bcsr = (u8 *)(CFG_BCSR);
+
+ bcsr[9] &= ~(0x01);
+}
--- /dev/null
+/*
+ * Copyright 2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __BCSR_H_
+#define __BCSR_H_
+
+#include <common.h>
+
+/* BCSR Bit definitions
+ * BCSR 0 *
+ 0:3 ccb sys pll
+ 4:6 cfg core pll
+ 7 cfg boot seq
+
+ * BCSR 1 *
+ 0:2 cfg rom lock
+ 3:5 cfg host agent
+ 6 PCI IO
+ 7 cfg RIO size
+
+ * BCSR 2 *
+ 0:4 QE PLL
+ 5 QE clock
+ 6 cfg PCI arbiter
+
+ * BCSR 3 *
+ 0 TSEC1 reduce
+ 1 TSEC2 reduce
+ 2:3 TSEC1 protocol
+ 4:5 TSEC2 protocol
+ 6 PHY1 slave
+ 7 PHY2 slave
+
+ * BCSR 4 *
+ 4 clock enable
+ 5 boot EPROM
+ 6 GETH transactive reset
+ 7 BRD write potect
+
+ * BCSR 5 *
+ 1:3 Leds 1-3
+ 4 UPC1 enable
+ 5 UPC2 enable
+ 6 UPC2 pos
+ 7 RS232 enable
+
+ * BCSR 6 *
+ 0 CFG ver 0
+ 1 CFG ver 1
+ 6 Register config led
+ 7 Power on reset
+
+ * BCSR 7 *
+ 2 board host mode indication
+ 5 enable TSEC1 PHY
+ 6 enable TSEC2 PHY
+
+ * BCSR 8 *
+ 0 UCC GETH1 enable
+ 1 UCC GMII enable
+ 3 UCC TBI enable
+ 5 UCC MII enable
+ 7 Real time clock reset
+
+ * BCSR 9 *
+ 0 UCC2 GETH enable
+ 1 UCC2 GMII enable
+ 3 UCC2 TBI enable
+ 5 UCC2 MII enable
+ 6 Ready only - indicate flash ready after burning
+ 7 Flash write protect
+*/
+
+/*BCSR Utils functions*/
+
+void enable_8568mds_duart(void);
+void enable_8568mds_flash_write(void);
+void disable_8568mds_flash_write(void);
+
+#endif /* __BCSR_H_ */
--- /dev/null
+#
+# Copyright 2007 Freescale Semiconductor.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8568mds board
+#
+TEXT_BASE = 0xfff80000
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8568=1
/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal SIMEK <monstrmonstr.eu>
+ * Copyright 2004-2007 Freescale Semiconductor.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* MA 02111-1307 USA
*/
- .text
- .globl microblaze_enable_interrupts
- .ent microblaze_enable_interrupts
- .align 2
-microblaze_enable_interrupts:
- addi r1, r1, -4
- swi r12, r1, 0
- mfs r12, rmsr
- ori r12, r12, 2
- mts rmsr, r12
- lwi r12, r1, 0
- rtsd r15, 8
- addi r1, r1, 4
- .end microblaze_enable_interrupts
+#include <common.h>
+
+#include <ft_build.h>
+
+extern void ft_cpu_setup(void *blob, bd_t *bd);
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup(void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+#ifdef CONFIG_PCI
+ ft_pci_setup(blob, bd);
+#endif
+ ft_cpu_setup(blob, bd);
+ p = ft_get_prop(blob, "/memory/reg", &len);
+ if (p != NULL) {
+ *p++ = cpu_to_be32(bd->bi_memstart);
+ *p = cpu_to_be32(bd->bi_memsize);
+ }
+}
+#endif /* CONFIG_OF_FLAT_TREE && CONFIG_OF_BOARD_SETUP */
--- /dev/null
+/*
+ * Copyright 2004-2007 Freescale Semiconductor.
+ * Copyright 2002,2003, Motorola Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+#define entry_start \
+ mflr r1 ; \
+ bl 0f ;
+
+#define entry_end \
+0: mflr r0 ; \
+ mtlr r1 ; \
+ blr ;
+
+
+ .section .bootpg, "ax"
+ .globl tlb1_entry
+tlb1_entry:
+ entry_start
+
+ /*
+ * Number of TLB0 and TLB1 entries in the following table
+ */
+ .long (2f-1f)/16
+
+1:
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+ /*
+ * TLB0 4K Non-cacheable, guarded
+ * 0xff700000 4K Initial CCSRBAR mapping
+ *
+ * This ends up at a TLB0 Index==0 entry, and must not collide
+ * with other TLB0 Entries.
+ */
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+#else
+#error("Update the number of table entries in tlb1_entry")
+#endif
+
+ /*
+ * TLB0 16K Cacheable, non-guarded
+ * 0xd001_0000 16K Temporary Global data for initialization
+ *
+ * Use four 4K TLB0 entries. These entries must be cacheable
+ * as they provide the bootstrap memory before the memory
+ * controler and real memory have been configured.
+ *
+ * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+ * and must not collide with other TLB0 entries.
+ */
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+ 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+ 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(0, 0, 0)
+ .long TLB1_MAS1(1, 0, 0, 0, 0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+ 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ /* TLB 1 Initializations */
+ /*
+ * TLBe 0: 16M Non-cacheable, guarded
+ * 0xff000000 16M FLASH (upper half)
+ * Out of reset this entry is only 4K.
+ */
+ .long TLB1_MAS0(1, 0, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE + 0x1000000),
+ 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE + 0x1000000),
+ 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLBe 1: 16M Non-cacheable, guarded
+ * 0xfe000000 16M FLASH (lower half)
+ */
+ .long TLB1_MAS0(1, 1, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLBe 2: 256M Non-cacheable, guarded
+ * 0x80000000 256M PCI1 MEM
+ */
+ .long TLB1_MAS0(1, 2, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLBe 3: 256M Non-cacheable, guarded
+ * 0xa0000000 256M PCIe Mem
+ */
+ .long TLB1_MAS0(1, 3, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_PEX_MEM_BASE), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_PEX_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLBe 4: Reserved for future usage
+ */
+
+ /*
+ * TLBe 5: 64M Non-cacheable, guarded
+ * 0xe000_0000 1M CCSRBAR
+ * 0xe200_0000 8M PCI1 IO
+ * 0xe280_0000 8M PCIe IO
+ */
+ .long TLB1_MAS0(1, 5, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLBe 6: 64M Cacheable, non-guarded
+ * 0xf000_0000 64M LBC SDRAM
+ */
+ .long TLB1_MAS0(1, 6, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+ /*
+ * TLBe 7: 256K Non-cacheable, guarded
+ * 0xf8000000 32K BCSR
+ * 0xf8008000 32K PIB (CS4)
+ * 0xf8010000 32K PIB (CS5)
+ */
+ .long TLB1_MAS0(1, 7, 0)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256K)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_BCSR_BASE), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_BCSR_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+2:
+ entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ *0) 0x0000_0000 0x7fff_ffff DDR 2G
+ *1) 0x8000_0000 0x9fff_ffff PCI1 MEM 256MB
+ *2) 0xa000_0000 0xbfff_ffff PCIe MEM 256MB
+ *5) 0xc000_0000 0xdfff_ffff SRIO 256MB
+ *-) 0xe000_0000 0xe00f_ffff CCSR 1M
+ *3) 0xe200_0000 0xe27f_ffff PCI1 I/O 8M
+ *4) 0xe280_0000 0xe2ff_ffff PCIe I/0 8M
+ *6.a) 0xf000_0000 0xf3ff_ffff SDRAM 64MB
+ *6.b) 0xf800_0000 0xf800_7fff BCSR 32KB
+ *6.c) 0xf800_8000 0xf800_ffff PIB (CS4) 32KB
+ *6.d) 0xf801_0000 0xf801_7fff PIB (CS5) 32KB
+ *6.e) 0xfe00_0000 0xffff_ffff Flash 32MB
+ *
+ *Notes:
+ * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
+ *
+ * The defines below are 1-off of the actual LAWAR0 usage.
+ * So LAWAR3 define uses the LAWAR4 register in the ECM.
+ */
+
+#define LAWBAR0 0
+#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+#define LAWBAR2 ((CFG_PEX_MEM_BASE>>12) & 0xfffff)
+#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff)
+#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_8M))
+
+#define LAWBAR4 ((CFG_PEX_IO_PHYS>>12) & 0xfffff)
+#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+
+#define LAWBAR5 ((CFG_SRIO_MEM_BASE>>12) & 0xfffff)
+#define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+/* LBC window - maps 256M. That's SDRAM, BCSR, PIBs, and Flash */
+#define LAWBAR6 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR6 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+ .section .bootpg, "ax"
+ .globl law_entry
+
+law_entry:
+ entry_start
+ .long (4f-3f)/8
+3:
+ .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
+ .long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5,LAWBAR6,LAWAR6
+4:
+ entry_end
--- /dev/null
+/*
+ * Copyright 2007 Freescale Semiconductor.
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <spd.h>
+
+#include "bcsr.h"
+
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void local_bus_init(void);
+void sdram_init(void);
+
+int board_early_init_f (void)
+{
+ /*
+ * Initialize local bus.
+ */
+ local_bus_init ();
+
+ enable_8568mds_duart();
+ enable_8568mds_flash_write();
+
+ return 0;
+}
+
+int checkboard (void)
+{
+ printf ("Board: 8568 MDS\n");
+
+ return 0;
+}
+
+long int
+initdram(int board_type)
+{
+ long dram_size = 0;
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+
+ puts("Initializing\n");
+
+#if defined(CONFIG_DDR_DLL)
+ {
+ /*
+ * Work around to stabilize DDR DLL MSYNC_IN.
+ * Errata DDR9 seems to have been fixed.
+ * This is now the workaround for Errata DDR11:
+ * Override DLL = 1, Course Adj = 1, Tap Select = 0
+ */
+
+ volatile ccsr_gur_t *gur= &immap->im_gur;
+
+ gur->ddrdllcr = 0x81000000;
+ asm("sync;isync;msync");
+ udelay(200);
+ }
+#endif
+ dram_size = spd_sdram();
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+ /*
+ * Initialize and enable DDR ECC.
+ */
+ ddr_enable_ecc(dram_size);
+#endif
+ /*
+ * SDRAM Initialization
+ */
+ sdram_init();
+
+ puts(" DDR: ");
+ return dram_size;
+}
+
+/*
+ * Initialize Local Bus
+ */
+void
+local_bus_init(void)
+{
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile ccsr_gur_t *gur = &immap->im_gur;
+ volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+
+ uint clkdiv;
+ uint lbc_hz;
+ sys_info_t sysinfo;
+
+ get_sys_info(&sysinfo);
+ clkdiv = (lbc->lcrr & 0x0f) * 2;
+ lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
+
+ gur->lbiuiplldcr1 = 0x00078080;
+ if (clkdiv == 16) {
+ gur->lbiuiplldcr0 = 0x7c0f1bf0;
+ } else if (clkdiv == 8) {
+ gur->lbiuiplldcr0 = 0x6c0f1bf0;
+ } else if (clkdiv == 4) {
+ gur->lbiuiplldcr0 = 0x5c0f1bf0;
+ }
+
+ lbc->lcrr |= 0x00030000;
+
+ asm("sync;isync;msync");
+}
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+void
+sdram_init(void)
+{
+#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)
+
+ uint idx;
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+ uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
+ uint lsdmr_common;
+
+ puts(" SDRAM: ");
+
+ print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+ /*
+ * Setup SDRAM Base and Option Registers
+ */
+ lbc->or2 = CFG_OR2_PRELIM;
+ asm("msync");
+
+ lbc->br2 = CFG_BR2_PRELIM;
+ asm("msync");
+
+ lbc->lbcr = CFG_LBC_LBCR;
+ asm("msync");
+
+
+ lbc->lsrt = CFG_LBC_LSRT;
+ lbc->mrtpr = CFG_LBC_MRTPR;
+ asm("msync");
+
+ /*
+ * MPC8568 uses "new" 15-16 style addressing.
+ */
+ lsdmr_common = CFG_LBC_LSDMR_COMMON;
+ lsdmr_common |= CFG_LBC_LSDMR_BSMA1516;
+
+ /*
+ * Issue PRECHARGE ALL command.
+ */
+ lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL;
+ asm("sync;msync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+
+ /*
+ * Issue 8 AUTO REFRESH commands.
+ */
+ for (idx = 0; idx < 8; idx++) {
+ lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH;
+ asm("sync;msync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+ }
+
+ /*
+ * Issue 8 MODE-set command.
+ */
+ lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW;
+ asm("sync;msync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(100);
+
+ /*
+ * Issue NORMAL OP command.
+ */
+ lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL;
+ asm("sync;msync");
+ *sdram_addr = 0xff;
+ ppcDcbf((unsigned long) sdram_addr);
+ udelay(200); /* Overkill. Must wait > 200 bus cycles */
+
+#endif /* enable SDRAM init */
+}
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+ uint *pstart = (uint *) CFG_MEMTEST_START;
+ uint *pend = (uint *) CFG_MEMTEST_END;
+ uint *p;
+
+ printf("Testing DRAM from 0x%08x to 0x%08x\n",
+ CFG_MEMTEST_START,
+ CFG_MEMTEST_END);
+
+ printf("DRAM test phase 1:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0xaaaaaaaa;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0xaaaaaaaa) {
+ printf ("DRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf("DRAM test phase 2:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0x55555555;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0x55555555) {
+ printf ("DRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf("DRAM test passed.\n");
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_PCI)
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc8568mds_config_table[] = {
+ {
+ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+ pci_cfgfunc_config_device,
+ {PCI_ENET0_IOADDR,
+ PCI_ENET0_MEMADDR,
+ PCI_COMMON_MEMORY | PCI_COMMAND_MASTER}
+ },
+ {}
+};
+#endif
+
+static struct pci_controller hose[] = {
+#ifndef CONFIG_PCI_PNP
+ { config_table: pci_mpc8568mds_config_table,},
+#endif
+#ifdef CONFIG_MPC85XX_PCI2
+ {},
+#endif
+};
+
+#endif /* CONFIG_PCI */
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+ pci_mpc85xx_init(&hose);
+#endif
+}
--- /dev/null
+/*
+ * Copyright 2004-2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+
+SECTIONS
+{
+ /* ELIOR - From RAM: From FLASH: 0xFFFFFFFC*/
+ .resetvec 0xFFFFFFFC:
+ {
+ *(.resetvec)
+ } = 0xffff
+
+ /*(ELIOR - From RAM: From FLASH: 0xFFFFF000*/
+ .bootpg 0xFFFFF000:
+ {
+ cpu/mpc85xx/start.o (.bootpg)
+ board/mpc8568mds/init.o (.bootpg)
+ } = 0xffff
+
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/mpc85xx/start.o (.text)
+ board/mpc8568mds/init.o (.text)
+ cpu/mpc85xx/traps.o (.text)
+ cpu/mpc85xx/interrupts.o (.text)
+ cpu/mpc85xx/cpu_init.o (.text)
+ cpu/mpc85xx/cpu.o (.text)
+ cpu/mpc85xx/speed.o (.text)
+ cpu/mpc85xx/pci.o (.text)
+ common/dlmalloc.o (.text)
+ lib_generic/crc32.o (.text)
+ lib_ppc/extable.o (.text)
+ lib_generic/zlib.o (.text)
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
#define LAWBAR3 ((CFG_PCI2_MEM_BASE>>12) & 0xffffff)
-#define LAWAR3 (~LAWAR_EN & (LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M)))
+#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
/*
* This is not so much the SDRAM map as it is the whole localbus map.
#define LAWBAR4 ((0xf8100000>>12) & 0xffffff)
#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_2M))
-#define LAWBAR5 ((CFG_PCI1_IO_BASE>>12) & 0xffffff)
+#define LAWBAR5 ((CFG_PCI1_IO_PHYS>>12) & 0xffffff)
#define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
-#define LAWBAR6 ((CFG_PCI2_IO_BASE>>12) & 0xffffff)
-#define LAWAR6 (~LAWAR_EN &( LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M)))
+#define LAWBAR6 ((CFG_PCI2_IO_PHYS>>12) & 0xffffff)
+#define LAWAR6 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))
#define LAWBAR7 ((0xfe000000 >>12) & 0xffffff)
#define LAWAR7 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M))
#define LAWAR8 ((LAWAR_TRGT_IF_DDR2 | (LAWAR_SIZE & LAWAR_SIZE_512M)) & ~LAWAR_EN)
#endif
-#define LAWBAR9 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
+#define LAWBAR9 ((CFG_RIO_MEM_PHYS>>12) & 0xfffff)
#define LAWAR9 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
.section .bootpg, "ax"
+#
TEXT_BASE = 0x01f00000
-
-# include NPE ethernet driver
-BOARDLIBS = $(obj)cpu/ixp/npe/libnpe.a
# Version: Xilinx EDK 6.3 EDK_Gmm.12.3
#
-TEXT_BASE = 0x12000000
+TEXT_BASE = 0x29000000
PLATFORM_CPPFLAGS += -mno-xl-soft-mul
PLATFORM_CPPFLAGS += -mno-xl-soft-div
#include <common.h>
#include <config.h>
+#include <asm/microblaze_intc.h>
+#include <asm/asm.h>
void do_reset (void)
{
int gpio_init (void)
{
#ifdef CFG_GPIO_0
- *((unsigned long *)(CFG_GPIO_0_ADDR)) = 0x0;
+ *((unsigned long *)(CFG_GPIO_0_ADDR)) = 0xFFFFFFFF;
#endif
return 0;
}
+
+#ifdef CFG_FSL_2
+void fsl_isr2 (void *arg) {
+ volatile int num;
+ *((unsigned int *)(CFG_GPIO_0_ADDR + 0x4)) =
+ ++(*((unsigned int *)(CFG_GPIO_0_ADDR + 0x4)));
+ GET (num, 2);
+ NGET (num, 2);
+ puts("*");
+}
+
+void fsl_init2 (void) {
+ puts("fsl_init2\n");
+ install_interrupt_handler (FSL_INTR_2,\
+ fsl_isr2,\
+ NULL);
+}
+#endif
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
- *
* CAUTION: This file is automatically generated by libgen.
- * Version: Xilinx EDK 6.3 EDK_Gmm.12.3
+ * Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4
*/
/* System Clock Frequency */
-#define XILINX_CLOCK_FREQ 66666667
+#define XILINX_CLOCK_FREQ 100000000
+
+/* Microblaze is microblaze_0 */
+#define XILINX_USE_MSR_INSTR 1
+#define XILINX_FSL_NUMBER 3
-/* Interrupt controller is intc_0 */
-#define XILINX_INTC_BASEADDR 0xd1000fc0
-#define XILINX_INTC_NUM_INTR_INPUTS 12
+/* Interrupt controller is opb_intc_0 */
+#define XILINX_INTC_BASEADDR 0x41200000
+#define XILINX_INTC_NUM_INTR_INPUTS 6
-/* Timer pheriphery is opb_timer_0 */
-#define XILINX_TIMER_BASEADDR 0xa2000000
+/* Timer pheriphery is opb_timer_1 */
+#define XILINX_TIMER_BASEADDR 0x41c00000
#define XILINX_TIMER_IRQ 0
-/* Uart pheriphery is console_uart */
-#define XILINX_UART_BASEADDR 0xa0000000
+/* Uart pheriphery is RS232_Uart */
+#define XILINX_UART_BASEADDR 0x40600000
#define XILINX_UART_BAUDRATE 115200
-/* GPIO is opb_gpio_0*/
-#define XILINX_GPIO_BASEADDR 0x90000000
+/* IIC pheriphery is IIC_EEPROM */
+#define XILINX_IIC_0_BASEADDR 0x40800000
+#define XILINX_IIC_0_FREQ 100000
+#define XILINX_IIC_0_BIT 0
+
+/* GPIO is LEDs_4Bit*/
+#define XILINX_GPIO_BASEADDR 0x40000000
-/* Flash Memory is opb_emc_0 */
-#define XILINX_FLASH_START 0x28000000
+/* Flash Memory is FLASH_2Mx32 */
+#define XILINX_FLASH_START 0x2c000000
#define XILINX_FLASH_SIZE 0x00800000
-/* Main Memory is plb_ddr_0 */
-#define XILINX_RAM_START 0x10000000
-#define XILINX_RAM_SIZE 0x10000000
+/* Main Memory is DDR_SDRAM_64Mx32 */
+#define XILINX_RAM_START 0x28000000
+#define XILINX_RAM_SIZE 0x04000000
-/* Sysace Controller is opb_sysace_0 */
-#define XILINX_SYSACE_BASEADDR 0xCF000000
-#define XILINX_SYSACE_HIGHADDR 0xCF0001FF
+/* Sysace Controller is SysACE_CompactFlash */
+#define XILINX_SYSACE_BASEADDR 0x41800000
+#define XILINX_SYSACE_HIGHADDR 0x4180ffff
#define XILINX_SYSACE_MEM_WIDTH 16
-/* Ethernet controller is opb_ethernet_0 */
+/* Ethernet controller is Ethernet_MAC */
#define XPAR_XEMAC_NUM_INSTANCES 1
#define XPAR_OPB_ETHERNET_0_DEVICE_ID 0
-#define XPAR_OPB_ETHERNET_0_BASEADDR 0x60000000
-#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x60003FFF
+#define XPAR_OPB_ETHERNET_0_BASEADDR 0x40c00000
+#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x40c0ffff
#define XPAR_OPB_ETHERNET_0_DMA_PRESENT 1
#define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST 1
#define XPAR_OPB_ETHERNET_0_MII_EXIST 1
memsize.o miiphybb.o miiphyutil.o \
s_record.o serial.o soft_i2c.o soft_spi.o spartan2.o spartan3.o \
usb.o usb_kbd.o usb_storage.o \
- virtex2.o xilinx.o crc16.o xyzModem.o cmd_mac.o
+ virtex2.o xilinx.o crc16.o xyzModem.o cmd_mac.o cmd_mfsl.o
SRCS := $(AOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(AOBJS) $(COBJS))
--- /dev/null
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Microblaze FSL support
+ */
+
+#include <common.h>
+#include <config.h>
+#include <command.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_MFSL)
+#include <asm/asm.h>
+
+int do_frd (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ unsigned int fslnum;
+ unsigned int num;
+ unsigned int blocking;
+
+ if (argc < 2) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ fslnum = (unsigned int)simple_strtoul (argv[1], NULL, 16);
+ blocking = (unsigned int)simple_strtoul (argv[2], NULL, 16);
+ if (fslnum < 0 || fslnum >= XILINX_FSL_NUMBER) {
+ puts ("Bad number of FSL\n");
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ switch (fslnum) {
+#if (XILINX_FSL_NUMBER > 0)
+ case 0:
+ switch (blocking) {
+ case 0: NGET (num, 0);
+ break;
+ case 1: NCGET (num, 0);
+ break;
+ case 2: GET (num, 0);
+ break;
+ case 3: CGET (num, 0);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 1)
+ case 1:
+ switch (blocking) {
+ case 0: NGET (num, 1);
+ break;
+ case 1: NCGET (num, 1);
+ break;
+ case 2: GET (num, 1);
+ break;
+ case 3: CGET (num, 1);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 2)
+ case 2:
+ switch (blocking) {
+ case 0: NGET (num, 2);
+ break;
+ case 1: NCGET (num, 2);
+ break;
+ case 2: GET (num, 2);
+ break;
+ case 3: CGET (num, 2);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 3)
+ case 3:
+ switch (blocking) {
+ case 0: NGET (num, 3);
+ break;
+ case 1: NCGET (num, 3);
+ break;
+ case 2: GET (num, 3);
+ break;
+ case 3: CGET (num, 3);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 4)
+ case 4:
+ switch (blocking) {
+ case 0: NGET (num, 4);
+ break;
+ case 1: NCGET (num, 4);
+ break;
+ case 2: GET (num, 4);
+ break;
+ case 3: CGET (num, 4);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 5)
+ case 5:
+ switch (blocking) {
+ case 0: NGET (num, 5);
+ break;
+ case 1: NCGET (num, 5);
+ break;
+ case 2: GET (num, 5);
+ break;
+ case 3: CGET (num, 5);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 6)
+ case 6:
+ switch (blocking) {
+ case 0: NGET (num, 6);
+ break;
+ case 1: NCGET (num, 6);
+ break;
+ case 2: GET (num, 6);
+ break;
+ case 3: CGET (num, 6);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 7)
+ case 7:
+ switch (blocking) {
+ case 0: NGET (num, 7);
+ break;
+ case 1: NCGET (num, 7);
+ break;
+ case 2: GET (num, 7);
+ break;
+ case 3: CGET (num, 7);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+ default:
+ return 1;
+ }
+
+ printf ("%01x: 0x%08lx - %s %s read\n", fslnum, num,
+ blocking < 2 ? "non blocking" : "blocking",
+ ((blocking == 1) || (blocking == 3)) ? "control" : "data" );
+ return 0;
+}
+
+int do_fwr (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ unsigned int fslnum;
+ unsigned int num;
+ unsigned int blocking;
+
+ if (argc < 3) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ fslnum = (unsigned int)simple_strtoul (argv[1], NULL, 16);
+ num = (unsigned int)simple_strtoul (argv[2], NULL, 16);
+ blocking = (unsigned int)simple_strtoul (argv[3], NULL, 16);
+ if (fslnum < 0 || fslnum >= XILINX_FSL_NUMBER) {
+ printf ("Bad number of FSL\nUsage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ switch (fslnum) {
+#if (XILINX_FSL_NUMBER > 0)
+ case 0:
+ switch (blocking) {
+ case 0: NPUT (num, 0);
+ break;
+ case 1: NCPUT (num, 0);
+ break;
+ case 2: PUT (num, 0);
+ break;
+ case 3: CPUT (num, 0);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 1)
+ case 1:
+ switch (blocking) {
+ case 0: NPUT (num, 1);
+ break;
+ case 1: NCPUT (num, 1);
+ break;
+ case 2: PUT (num, 1);
+ break;
+ case 3: CPUT (num, 1);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 2)
+ case 2:
+ switch (blocking) {
+ case 0: NPUT (num, 2);
+ break;
+ case 1: NCPUT (num, 2);
+ break;
+ case 2: PUT (num, 2);
+ break;
+ case 3: CPUT (num, 2);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 3)
+ case 3:
+ switch (blocking) {
+ case 0: NPUT (num, 3);
+ break;
+ case 1: NCPUT (num, 3);
+ break;
+ case 2: PUT (num, 3);
+ break;
+ case 3: CPUT (num, 3);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 4)
+ case 4:
+ switch (blocking) {
+ case 0: NPUT (num, 4);
+ break;
+ case 1: NCPUT (num, 4);
+ break;
+ case 2: PUT (num, 4);
+ break;
+ case 3: CPUT (num, 4);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 5)
+ case 5:
+ switch (blocking) {
+ case 0: NPUT (num, 5);
+ break;
+ case 1: NCPUT (num, 5);
+ break;
+ case 2: PUT (num, 5);
+ break;
+ case 3: CPUT (num, 5);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 6)
+ case 6:
+ switch (blocking) {
+ case 0: NPUT (num, 6);
+ break;
+ case 1: NCPUT (num, 6);
+ break;
+ case 2: PUT (num, 6);
+ break;
+ case 3: CPUT (num, 6);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 7)
+ case 7:
+ switch (blocking) {
+ case 0: NPUT (num, 7);
+ break;
+ case 1: NCPUT (num, 7);
+ break;
+ case 2: PUT (num, 7);
+ break;
+ case 3: CPUT (num, 7);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+ default:
+ return 1;
+ }
+
+ printf ("%01x: 0x%08lx - %s %s write\n", fslnum, num,
+ blocking < 2 ? "non blocking" : "blocking",
+ ((blocking == 1) || (blocking == 3)) ? "control" : "data" );
+ return 0;
+
+}
+
+int do_rspr (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ unsigned int reg = 0;
+ unsigned int val = 0;
+
+ reg = (unsigned int)simple_strtoul (argv[1], NULL, 16);
+ val = (unsigned int)simple_strtoul (argv[2], NULL, 16);
+ if (argc < 1) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+ switch (reg) {
+ case 0x1:
+ if (argc > 2) {
+ MTS (val, rmsr);
+ NOP;
+ MFS (val, rmsr);
+
+ } else {
+ MFS (val, rmsr);
+ }
+ puts ("MSR");
+ break;
+ case 0x3:
+ MFS (val, rear);
+ puts ("EAR");
+ break;
+ case 0x5:
+ MFS (val, resr);
+ puts ("ESR");
+ break;
+ default:
+ return 1;
+ }
+ printf (": 0x%08lx\n", val);
+ return 0;
+}
+
+/***************************************************/
+
+U_BOOT_CMD (frd, 3, 1, do_frd,
+ "frd - read data from FSL\n",
+ "- [fslnum [0|1|2|3]]\n"
+ " 0 - non blocking data read\n"
+ " 1 - non blocking control read\n"
+ " 2 - blocking data read\n"
+ " 3 - blocking control read\n");
+
+
+U_BOOT_CMD (fwr, 4, 1, do_fwr,
+ "fwr - write data to FSL\n",
+ "- [fslnum [0|1|2|3]]\n"
+ " 0 - non blocking data write\n"
+ " 1 - non blocking control write\n"
+ " 2 - blocking data write\n"
+ " 3 - blocking control write\n");
+
+U_BOOT_CMD (rspr, 3, 1, do_rspr,
+ "rmsr - read/write special purpose register\n",
+ "- reg_num [write value] read/write special purpose register\n"
+ " 0 - MSR - Machine status register\n"
+ " 1 - EAR - Exception address register\n"
+ " 2 - ESR - Exception status register\n");
+
+#endif /* CONFIG_MICROBLAZE & CFG_CMD_MFSL */
void setenv (char *varname, char *varvalue)
{
char *argv[4] = { "setenv", varname, varvalue, NULL };
- _do_setenv (0, 3, argv);
+ if (varvalue == NULL)
+ _do_setenv (0, 2, argv);
+ else
+ _do_setenv (0, 3, argv);
}
int do_setenv ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
/* suppress all output if splash screen is enabled and we have
a bmp to display */
if (getenv("splashimage") != NULL)
- outputdev = search_device (DEV_FLAGS_OUTPUT, "nulldev");
-#endif
-
-#ifdef CONFIG_SILENT_CONSOLE
- /* Suppress all output if "silent" mode requested */
- if (gd->flags & GD_FLG_SILENT)
- outputdev = search_device (DEV_FLAGS_OUTPUT, "nulldev");
+ gd->flags |= GD_FLG_SILENT;
#endif
/* Scan devices looking for input and output devices */
u_int presskey_max = 0;
u_int i;
-#ifdef CONFIG_SILENT_CONSOLE
- if (gd->flags & GD_FLG_SILENT) {
- /* Restore serial console */
- console_assign (stdout, "serial");
- console_assign (stderr, "serial");
- }
-#endif
-
# ifdef CONFIG_AUTOBOOT_PROMPT
printf (CONFIG_AUTOBOOT_PROMPT, bootdelay);
# endif
# endif
#ifdef CONFIG_SILENT_CONSOLE
- if (abort) {
- /* permanently enable normal console output */
- gd->flags &= ~(GD_FLG_SILENT);
- } else if (gd->flags & GD_FLG_SILENT) {
- /* Restore silent console */
- console_assign (stdout, "nulldev");
- console_assign (stderr, "nulldev");
- }
+ if (abort)
+ gd->flags &= ~GD_FLG_SILENT;
#endif
return abort;
{
int abort = 0;
-#ifdef CONFIG_SILENT_CONSOLE
- if (gd->flags & GD_FLG_SILENT) {
- /* Restore serial console */
- console_assign (stdout, "serial");
- console_assign (stderr, "serial");
- }
-#endif
-
#ifdef CONFIG_MENUPROMPT
printf(CONFIG_MENUPROMPT, bootdelay);
#else
if (tstc()) { /* we got a key press */
(void) getc(); /* consume input */
puts ("\b\b\b 0");
- abort = 1; /* don't auto boot */
+ abort = 1; /* don't auto boot */
}
}
#endif
putc ('\n');
#ifdef CONFIG_SILENT_CONSOLE
- if (abort) {
- /* permanently enable normal console output */
- gd->flags &= ~(GD_FLG_SILENT);
- } else if (gd->flags & GD_FLG_SILENT) {
- /* Restore silent console */
- console_assign (stdout, "nulldev");
- console_assign (stderr, "nulldev");
- }
+ if (abort)
+ gd->flags &= ~GD_FLG_SILENT;
#endif
return abort;
if (outputcnt)
*output = 0;
+ else
+ *(output - 1) = 0;
#ifdef DEBUG_PARSER
printf ("[PROCESS_MACROS] OUTPUT len %d: \"%s\"\n",
all: $(LIB)
-$(LIB): $(obj).depend $(OBJS)
+$(LIB): $(OBJS)
$(AR) $(ARFLAGS) $@ $(OBJS)
#########################################################################
LIB = $(obj)lib$(CPU).a
START = start.o
-SOBJS = dcache.o icache.o irq.o disable_int.o enable_int.o
+SOBJS = irq.o
COBJS = cpu.o interrupts.o cache.o exception.o timer.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
*/
#include <common.h>
+#include <asm/asm.h>
#if (CONFIG_COMMANDS & CFG_CMD_CACHE)
__asm__ __volatile__ ("and %0,%0,%1"::"r" (i), "r" (mask):"memory");
return i;
}
+
+void icache_enable (void) {
+ MSRSET(0x20);
+}
+
+void icache_disable(void) {
+ MSRCLR(0x20);
+}
+
+void dcache_enable (void) {
+ MSRSET(0x80);
+}
+
+void dcache_disable(void) {
+ MSRCLR(0x80);
+}
#endif
+++ /dev/null
-/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal SIMEK <monstr@monstr.eu>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
- .text
- .globl dcache_enable
- .ent dcache_enable
- .align 2
-dcache_enable:
- /* Make space on stack for a temporary */
- addi r1, r1, -4
- /* Save register r12 */
- swi r12, r1, 0
- /* Read the MSR register */
- mfs r12, rmsr
- /* Set the instruction enable bit */
- ori r12, r12, 0x80
- /* Save the MSR register */
- mts rmsr, r12
- /* Load register r12 */
- lwi r12, r1, 0
- /* Return */
- rtsd r15, 8
- /* Update stack in the delay slot */
- addi r1, r1, 4
- .end dcache_enable
-
- .text
- .globl dcache_disable
- .ent dcache_disable
- .align 2
-dcache_disable:
- /* Make space on stack for a temporary */
- addi r1, r1, -4
- /* Save register r12 */
- swi r12, r1, 0
- /* Read the MSR register */
- mfs r12, rmsr
- /* Clear the data cache enable bit */
- andi r12, r12, ~0x80
- /* Save the MSR register */
- mts rmsr, r12
- /* Load register r12 */
- lwi r12, r1, 0
- /* Return */
- rtsd r15, 8
- /* Update stack in the delay slot */
- addi r1, r1, 4
- .end dcache_disable
*/
#include <common.h>
+#include <asm/asm.h>
void _hw_exception_handler (void)
{
int address = 0;
int state = 0;
/* loading address of exception EAR */
- __asm__ __volatile ("mfs %0,rear"::"r" (address):"memory");
+ MFS (address, rear);
/* loading excetpion state register ESR */
- __asm__ __volatile ("mfs %0,resr"::"r" (state):"memory");
+ MFS (state, resr);
printf ("Hardware exception at 0x%x address\n", address);
switch (state & 0x1f) { /* mask on exception cause */
case 0x1:
case 0x5:
puts ("Divide by zero exception\n");
break;
+#ifdef MICROBLAZE_V5
+ case 0x1000:
+ puts ("Exception in delay slot\n");
+ break;
+#endif
default:
puts ("Undefined cause\n");
break;
+++ /dev/null
-/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal SIMEK <monstr@monstr.eu>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
- .text
- .globl icache_enable
- .ent icache_enable
- .align 2
-icache_enable:
- /* Make space on stack for a temporary */
- addi r1, r1, -4
- /* Save register r12 */
- swi r12, r1, 0
- /* Read the MSR register */
- mfs r12, rmsr
- /* Set the instruction enable bit */
- ori r12, r12, 0x20
- /* Save the MSR register */
- mts rmsr, r12
- /* Load register r12 */
- lwi r12, r1, 0
- /* Return */
- rtsd r15, 8
- /* Update stack in the delay slot */
- addi r1, r1, 4
- .end icache_enable
-
- .text
- .globl icache_disable
- .ent icache_disable
- .align 2
-icache_disable:
- /* Make space on stack for a temporary */
- addi r1, r1, -4
- /* Save register r12 */
- swi r12, r1, 0
- /* Read the MSR register */
- mfs r12, rmsr
- /* Clear the instruction enable bit */
- andi r12, r12, ~0x20
- /* Save the MSR register */
- mts rmsr, r12
- /* Load register r12 */
- lwi r12, r1, 0
- /* Return */
- rtsd r15, 8
- /* Update stack in the delay slot */
- addi r1, r1, 4
- .end icache_disable
#include <common.h>
#include <command.h>
#include <asm/microblaze_intc.h>
+#include <asm/asm.h>
#undef DEBUG_INT
void enable_interrupts (void)
{
- microblaze_enable_interrupts ();
+ MSRSET(0x2);
}
int disable_interrupts (void)
{
- microblaze_disable_interrupts ();
+ MSRCLR(0x2);
return 0;
}
#ifdef CFG_TIMER_0
extern void timer_init (void);
#endif
+#ifdef CFG_FSL_2
+extern void fsl_init2 (void);
+#endif
+
static struct irq_action vecs[CFG_INTC_0_NUM];
act->count = 0;
enable_one_interrupt (irq);
} else { /* disable */
-
act->handler = (interrupt_handler_t *) def_hdlr;
act->arg = (void *)irq;
disable_one_interrupt (irq);
#ifdef CFG_TIMER_0
timer_init ();
#endif
+#ifdef CFG_FSL_2
+ fsl_init2 ();
+#endif
enable_interrupts ();
return 0;
}
void interrupt_handler (void)
{
- int irqs;
- irqs = (intc->isr & intc->ier); /* find active interrupt */
-
+ int irqs = (intc->isr & intc->ier); /* find active interrupt */
+ int i = 1;
#ifdef DEBUG_INT
+ int value;
printf ("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
intc->iar, intc->mer);
+ R14(value);
printf ("Interrupt handler on %x line, r14 %x\n", irqs, value);
#endif
struct irq_action *act = vecs;
#endif
act->handler (act->arg);
act->count++;
+ intc->iar = i;
+ return;
}
irqs >>= 1;
act++;
+ i <<= 1;
}
- intc->iar = 0xFFFFFFFF; /* erase all events */
-#ifdef DEBUG
+
+#ifdef DEBUG_INT
printf ("Dump INTC reg, isr %x, ier %x, iar %x, mer %x\n", intc->isr,
intc->ier, intc->iar, intc->mer);
- printf ("Interrupt handler on %x line, r14\n", irqs);
+ R14(value);
+ printf ("Interrupt handler on %x line, r14 %x\n", irqs, value);
#endif
}
#endif
*/
#include <config.h>
+#include <asm/asm.h>
.text
.global _interrupt_handler
_interrupt_handler:
addi r1, r1, 4
/* enable_interrupt */
+#ifdef XILINX_USE_MSR_INSTR
+ msrset r0, 2
+#else
+ /* FIXME unstable in stressed mode - two irqs */
+ nop
addi r1, r1, -4
swi r12, r1, 0
mfs r12, rmsr
lwi r12, r1, 0
addi r1, r1, 4
nop
+#endif
bra r14
nop
nop
3: /* jumping to board_init */
brai board_init
1: bri 1b
+
+/*
+ * Read 16bit little endian
+ */
+ .text
+ .global in16
+ .ent in16
+ .align 2
+in16: lhu r3, r0, r5
+ bslli r4, r3, 8
+ bsrli r3, r3, 8
+ andi r4, r4, 0xffff
+ or r3, r3, r4
+ rtsd r15, 8
+ sext16 r3, r3
+ .end in16
+
+/*
+ * Write 16bit little endian
+ * first parameter(r5) - address, second(r6) - short value
+ */
+ .text
+ .global out16
+ .ent out16
+ .align 2
+out16: bslli r3, r6, 8
+ bsrli r6, r6, 8
+ andi r3, r3, 0xffff
+ or r3, r3, r6
+ sh r3, r0, r5
+ rtsd r15, 8
+ or r0, r0, r0
+ .end out16
#include <common.h>
#include <asm/microblaze_timer.h>
+#include <asm/microblaze_intc.h>
volatile int timestamp = 0;
#ifdef CFG_INTC_0
#ifdef CFG_TIMER_0
-extern void install_interrupt_handler (int irq, interrupt_handler_t * hdlr,
- void *arg);
-
microblaze_timer_t *tmr = (microblaze_timer_t *) (CFG_TIMER_0_ADDR);
void timer_isr (void *arg)
#else
svr = get_svr();
pvr = get_pvr();
- switch (SVR_VER (svr)) {
- case SVR_MPC5200:
- printf ("MPC5200");
+
+ switch (pvr) {
+ case PVR_5200:
+ printf("MPC5200");
+ break;
+ case PVR_5200B:
+ printf("MPC5200B");
break;
default:
- printf ("MPC52?? (SVR %08x)", svr);
+ printf("Unknown MPC5xxx");
break;
}
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@3000/mac-address", &len);
if (p != NULL)
memcpy(p, bd->bi_enetaddr, 6);
+
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@3000/local-mac-address", &len);
+ if (p != NULL)
+ memcpy(p, bd->bi_enetaddr, 6);
}
#endif
*(vu_long *)(MPC5XXX_XLBARB + 0x40) |= (1 << 15);
*(vu_long *)(MPC5XXX_XLBARB + 0x70) = CFG_SDRAM_BASE | 0x1d;
-# if defined(CFG_IPBSPEED_133)
+# if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/* Motorola reports IPB should better run at 133 MHz. */
*(vu_long *)MPC5XXX_ADDECR |= 1;
/* pci_clk_sel = 0x02, ipb_clk_sel = 0x00; */
addecr = *(vu_long *)MPC5XXX_CDM_CFG;
addecr &= ~0x103;
-# if defined(CFG_PCISPEED_66)
+# if defined(CFG_PCICLK_EQUALS_IPBCLK_DIV2)
/* pci_clk_sel = 0x01 -> IPB_CLK/2 */
addecr |= 0x01;
# else
/* pci_clk_sel = 0x02 -> XLB_CLK/4 = IPB_CLK/4 */
addecr |= 0x02;
-# endif /* CFG_PCISPEED_66 */
+# endif /* CFG_PCICLK_EQUALS_IPBCLK_DIV2 */
*(vu_long *)MPC5XXX_CDM_CFG = addecr;
-# endif /* CFG_IPBSPEED_133 */
+# endif /* CFG_IPBCLK_EQUALS_XLBCLK */
/* Configure the XLB Arbiter */
*(vu_long *)MPC5XXX_XLBARB_MPRIEN = 0xff;
*(vu_long *)MPC5XXX_XLBARB_MPRIVAL = 0x11111111;
*/
fec->eth->imask = 0x00000000;
+/*
+ * In original Promess-provided code PHY initialization is disabled with the
+ * following comment: "Phy initialization is DISABLED for now. There was a
+ * problem with running 100 Mbps on PRO board". Thus we temporarily disable
+ * PHY initialization for the Motion-PRO board, until a proper fix is found.
+ */
+
if (fec->xcv_type != SEVENWIRE) {
/*
* Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
START = start.o
COBJS = traps.o cpu.o cpu_init.o speed.o interrupts.o \
- spd_sdram.o qe_io.o
+ spd_sdram.o qe_io.o pci.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
immr = (immap_t *)CFG_IMMR;
- if ((pvr & 0xFFFF0000) != PVR_83xx) {
- puts("Not MPC83xx Family!!!\n");
- return -1;
+ puts("CPU: ");
+
+ switch (pvr & 0xffff0000) {
+ case PVR_E300C1:
+ printf("e300c1, ");
+ break;
+
+ case PVR_E300C2:
+ printf("e300c2, ");
+ break;
+
+ case PVR_E300C3:
+ printf("e300c3, ");
+ break;
+
+ default:
+ printf("Unknown core, ");
}
spridr = immr->sysconf.spridr;
- puts("CPU: ");
switch(spridr) {
case SPR_8349E_REV10:
case SPR_8349E_REV11:
case SPR_8321_REV11:
puts("MPC8321, ");
break;
+ case SPR_8311_REV10:
+ puts("MPC8311, ");
+ break;
+ case SPR_8311E_REV10:
+ puts("MPC8311E, ");
+ break;
+ case SPR_8313_REV10:
+ puts("MPC8313, ");
+ break;
+ case SPR_8313E_REV10:
+ puts("MPC8313E, ");
+ break;
default:
puts("Rev: Unknown revision number.\nWarning: Unsupported cpu revision!\n");
return 0;
/* Multiple revisons of 834x processors may have the same SPRIDR value.
* So use PVR to identify the revision number.
*/
- printf("Rev: %02x at %s MHz\n", PVR_MAJ(pvr)<<4 | PVR_MIN(pvr), strmhz(buf, clock));
+ printf("Rev: %02x at %s MHz", PVR_MAJ(pvr)<<4 | PVR_MIN(pvr), strmhz(buf, clock));
#else
- printf("Rev: %02x at %s MHz\n", spridr & 0x0000FFFF, strmhz(buf, clock));
+ printf("Rev: %02x at %s MHz", spridr & 0x0000FFFF, strmhz(buf, clock));
#endif
+ printf(", CSB: %4d MHz\n", gd->csb_clk / 1000000);
+
return 0;
}
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2007
+ *
+ * Author: Scott Wood <scottwood@freescale.com>,
+ * with some bits from older board-specific PCI initialization.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <ft_build.h>
+#include <asm/mpc8349_pci.h>
+
+#ifdef CONFIG_83XX_GENERIC_PCI
+#define MAX_BUSES 2
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct pci_controller pci_hose[MAX_BUSES];
+static int pci_num_buses;
+
+static void pci_init_bus(int bus, struct pci_region *reg)
+{
+ volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+ volatile pot83xx_t *pot = immr->ios.pot;
+ volatile pcictrl83xx_t *pci_ctrl = &immr->pci_ctrl[bus];
+ struct pci_controller *hose = &pci_hose[bus];
+ u32 dev;
+ u16 reg16;
+ int i;
+
+ if (bus == 1)
+ pot += 3;
+
+ /* Setup outbound translation windows */
+ for (i = 0; i < 3; i++, reg++, pot++) {
+ if (reg->size == 0)
+ break;
+
+ hose->regions[i] = *reg;
+ hose->region_count++;
+
+ pot->potar = reg->bus_start >> 12;
+ pot->pobar = reg->phys_start >> 12;
+ pot->pocmr = ~(reg->size - 1) >> 12;
+
+ if (reg->flags & PCI_REGION_IO)
+ pot->pocmr |= POCMR_IO;
+#ifdef CONFIG_83XX_PCI_STREAMING
+ else if (reg->flags & PCI_REGION_PREFETCH)
+ pot->pocmr |= POCMR_SE;
+#endif
+
+ if (bus == 1)
+ pot->pocmr |= POCMR_DST;
+
+ pot->pocmr |= POCMR_EN;
+ }
+
+ /* Point inbound translation at RAM */
+ pci_ctrl->pitar1 = 0;
+ pci_ctrl->pibar1 = 0;
+ pci_ctrl->piebar1 = 0;
+ pci_ctrl->piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP |
+ PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
+
+ i = hose->region_count++;
+ hose->regions[i].bus_start = 0;
+ hose->regions[i].phys_start = 0;
+ hose->regions[i].size = gd->ram_size;
+ hose->regions[i].flags = PCI_REGION_MEM | PCI_REGION_MEMORY;
+
+ hose->first_busno = 0;
+ hose->last_busno = 0xff;
+
+ pci_setup_indirect(hose, CFG_IMMR + 0x8300 + bus * 0x80,
+ CFG_IMMR + 0x8304 + bus * 0x80);
+
+ pci_register_hose(hose);
+
+ /*
+ * Write to Command register
+ */
+ reg16 = 0xff;
+ dev = PCI_BDF(hose->first_busno, 0, 0);
+ pci_hose_read_config_word(hose, dev, PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
+ pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
+ pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
+
+#ifdef CONFIG_PCI_SCAN_SHOW
+ printf("PCI: Bus Dev VenId DevId Class Int\n");
+#endif
+ /*
+ * Hose scan.
+ */
+ hose->last_busno = pci_hose_scan(hose);
+}
+
+/*
+ * The caller must have already set OCCR, and the PCI_LAW BARs
+ * must have been set to cover all of the requested regions.
+ *
+ * If fewer than three regions are requested, then the region
+ * list is terminated with a region of size 0.
+ */
+void mpc83xx_pci_init(int num_buses, struct pci_region **reg, int warmboot)
+{
+ volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+ int i;
+
+ if (num_buses > MAX_BUSES) {
+ printf("%d PCI buses requsted, %d supported\n",
+ num_buses, MAX_BUSES);
+
+ num_buses = MAX_BUSES;
+ }
+
+ pci_num_buses = num_buses;
+
+ /*
+ * Release PCI RST Output signal.
+ * Power on to RST high must be at least 100 ms as per PCI spec.
+ * On warm boots only 1 ms is required.
+ */
+ udelay(warmboot ? 1000 : 100000);
+
+ for (i = 0; i < num_buses; i++)
+ immr->pci_ctrl[i].gcr = 1;
+
+ /*
+ * RST high to first config access must be at least 2^25 cycles
+ * as per PCI spec. This could be cut in half if we know we're
+ * running at 66MHz. This could be insufficiently long if we're
+ * running the PCI bus at significantly less than 33MHz.
+ */
+ udelay(1020000);
+
+ for (i = 0; i < num_buses; i++)
+ pci_init_bus(i, reg[i]);
+}
+
+#ifdef CONFIG_OF_FLAT_TREE
+void ft_pci_setup(void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+
+ if (pci_num_buses < 1)
+ return;
+
+ p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8500/bus-range", &len);
+ if (p) {
+ p[0] = pci_hose[0].first_busno;
+ p[1] = pci_hose[0].last_busno;
+ }
+
+ if (pci_num_buses < 2)
+ return;
+
+ p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8600/bus-range", &len);
+ if (p) {
+ p[0] = pci_hose[1].first_busno;
+ p[1] = pci_hose[1].last_busno;
+ }
+}
+#endif /* CONFIG_OF_FLAT_TREE */
+
+#endif /* CONFIG_83XX_GENERIC_PCI */
int clks;
ddr_bus_clk = gd->ddr_clk >> 1;
- clks = picos / ((1000000000 / ddr_bus_clk) * 1000);
- if (picos % ((1000000000 / ddr_bus_clk) * 1000) != 0)
+ clks = picos / (1000000000 / (ddr_bus_clk / 1000));
+ if (picos % (1000000000 / (ddr_bus_clk / 1000)) != 0)
clks++;
return clks;
| (1 << (16 + 10)) /* DQS Differential disable */
| (add_lat << (16 + 3)) /* Additive Latency in EMRS1 */
| (mode_odt_enable << 16) /* ODT Enable in EMRS1 */
- | ((twr_clk >> 1) << 9) /* Write Recovery Autopre */
+ | ((twr_clk - 1) << 9) /* Write Recovery Autopre */
| (caslat << 4) /* caslat */
| (burstlen << 0) /* Burst length */
);
#ifdef CFG_DDR_SDRAM_CLK_CNTL /* Optional platform specific value */
ddr->sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL;
-#else
- /* SS_EN = 0, source synchronous disable
- * CLK_ADJST = 0, MCK/MCK# is launched aligned with addr/cmd
- */
- ddr->sdram_clk_cntl = 0x00000000;
#endif
debug("DDR:sdram_clk_cntl=0x%08x\n", ddr->sdram_clk_cntl);
#include <common.h>
#include <mpc83xx.h>
+#include <command.h>
#include <asm/processor.h>
DECLARE_GLOBAL_DATA_PTR;
u32 lcrr;
u32 csb_clk;
-#if defined(CONFIG_MPC834X)
+#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X)
u32 tsec1_clk;
u32 tsec2_clk;
- u32 usbmph_clk;
u32 usbdr_clk;
#endif
+#ifdef CONFIG_MPC834X
+ u32 usbmph_clk;
+#endif
u32 core_clk;
u32 i2c1_clk;
#if !defined(CONFIG_MPC832X)
sccr = im->clk.sccr;
-#if defined(CONFIG_MPC834X)
+#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X)
switch ((sccr & SCCR_TSEC1CM) >> SCCR_TSEC1CM_SHIFT) {
case 0:
tsec1_clk = 0;
return -4;
}
+ switch ((sccr & SCCR_USBDRCM) >> SCCR_USBDRCM_SHIFT) {
+ case 0:
+ usbdr_clk = 0;
+ break;
+ case 1:
+ usbdr_clk = csb_clk;
+ break;
+ case 2:
+ usbdr_clk = csb_clk / 2;
+ break;
+ case 3:
+ usbdr_clk = csb_clk / 3;
+ break;
+ default:
+ /* unkown SCCR_USBDRCM value */
+ return -8;
+ }
+#endif
+
+#if defined(CONFIG_MPC834X)
switch ((sccr & SCCR_TSEC2CM) >> SCCR_TSEC2CM_SHIFT) {
case 0:
tsec2_clk = 0;
return -7;
}
- switch ((sccr & SCCR_USBDRCM) >> SCCR_USBDRCM_SHIFT) {
- case 0:
- usbdr_clk = 0;
- break;
- case 1:
- usbdr_clk = csb_clk;
- break;
- case 2:
- usbdr_clk = csb_clk / 2;
- break;
- case 3:
- usbdr_clk = csb_clk / 3;
- break;
- default:
- /* unkown SCCR_USBDRCM value */
- return -8;
- }
-
if (usbmph_clk != 0 && usbdr_clk != 0 && usbmph_clk != usbdr_clk) {
/* if USB MPH clock is not disabled and
* USB DR clock is not disabled then
*/
return -9;
}
+#elif defined(CONFIG_MPC831X)
+ tsec2_clk = tsec1_clk;
+
+ if (!(sccr & SCCR_TSEC1ON))
+ tsec1_clk = 0;
+ if (!(sccr & SCCR_TSEC2ON))
+ tsec2_clk = 0;
#endif
-#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X)
+
+#if !defined(CONFIG_MPC834X)
i2c1_clk = csb_clk;
#endif
#if !defined(CONFIG_MPC832X)
#endif
gd->csb_clk = csb_clk;
-#if defined(CONFIG_MPC834X)
+#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X)
gd->tsec1_clk = tsec1_clk;
gd->tsec2_clk = tsec2_clk;
- gd->usbmph_clk = usbmph_clk;
gd->usbdr_clk = usbdr_clk;
#endif
+#if defined(CONFIG_MPC834X)
+ gd->usbmph_clk = usbmph_clk;
+#endif
gd->core_clk = core_clk;
gd->i2c1_clk = i2c1_clk;
#if !defined(CONFIG_MPC832X)
return gd->csb_clk;
}
-int print_clock_conf(void)
+int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
printf("Clock configuration:\n");
- printf(" Coherent System Bus: %4d MHz\n", gd->csb_clk / 1000000);
printf(" Core: %4d MHz\n", gd->core_clk / 1000000);
+ printf(" Coherent System Bus: %4d MHz\n", gd->csb_clk / 1000000);
#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X)
printf(" QE: %4d MHz\n", gd->qe_clk / 1000000);
printf(" BRG: %4d MHz\n", gd->brg_clk / 1000000);
#if !defined(CONFIG_MPC832X)
printf(" I2C2: %4d MHz\n", gd->i2c2_clk / 1000000);
#endif
-#if defined(CONFIG_MPC834X)
+#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X)
printf(" TSEC1: %4d MHz\n", gd->tsec1_clk / 1000000);
printf(" TSEC2: %4d MHz\n", gd->tsec2_clk / 1000000);
- printf(" USB MPH: %4d MHz\n", gd->usbmph_clk / 1000000);
printf(" USB DR: %4d MHz\n", gd->usbdr_clk / 1000000);
#endif
+#if defined(CONFIG_MPC834X)
+ printf(" USB MPH: %4d MHz\n", gd->usbmph_clk / 1000000);
+#endif
return 0;
}
+
+U_BOOT_CMD(clocks, 1, 0, do_clocks,
+ "clocks - print clock configuration\n",
+ " clocks\n"
+);
/*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004,2007 Freescale Semiconductor, Inc.
* (C) Copyright 2002, 2003 Motorola Inc.
* Xianghua Xiao (X.Xiao@motorola.com)
*
case SVR_8548_E:
puts("8548_E");
break;
+ case SVR_8544:
+ puts("8544");
+ break;
+ case SVR_8544_E:
+ puts("8544_E");
+ break;
+ case SVR_8568_E:
+ puts("8568_E");
+ break;
default:
puts("Unknown");
break;
#endif
clkdiv = lcrr & 0x0f;
if (clkdiv == 2 || clkdiv == 4 || clkdiv == 8) {
-#ifdef CONFIG_MPC8548
+#if defined(CONFIG_MPC8548) || defined(CONFIG_MPC8544)
/*
* Yes, the entire PQ38 family use the same
* bit-representation for twice the clock divider values.
int do_reset (cmd_tbl_t *cmdtp, bd_t *bd, int flag, int argc, char *argv[])
{
+ uint pvr;
+ uint ver;
+ pvr = get_pvr();
+ ver = PVR_VER(pvr);
+ if (ver & 1){
+ /* e500 v2 core has reset control register */
+ volatile unsigned int * rstcr;
+ rstcr = (volatile unsigned int *)(CFG_IMMR + 0xE00B0);
+ *rstcr = 0x2; /* HRESET_REQ */
+ }else{
/*
* Initiate hard reset in debug control register DBCR0
* Make sure MSR[DE] = 1
*/
- unsigned long val;
-
- val = mfspr(DBCR0);
- val |= 0x70000000;
- mtspr(DBCR0,val);
-
+ unsigned long val;
+ val = mfspr(DBCR0);
+ val |= 0x70000000;
+ mtspr(DBCR0,val);
+ }
return 1;
}
* Clear TSR(WIS) bit by writing 1
*/
unsigned long val;
- val = mfspr(tsr);
- val |= 0x40000000;
- mtspr(tsr, val);
+ val = mfspr(SPRN_TSR);
+ val |= TSR_WIS;
+ mtspr(SPRN_TSR, val);
}
#endif /* CONFIG_WATCHDOG */
dma->satr0 = 0x02c40000;
dma->datr0 = 0x02c40000;
+ dma->sr0 = 0xfffffff; /* clear any errors */
asm("sync; isync; msync");
return;
}
status = dma->sr0;
}
+ /* clear MR0[CS] channel start bit */
+ dma->mr0 &= 0x00000001;
+ asm("sync;isync;msync");
+
if (status != 0) {
printf ("DMA Error: status = %x\n", status);
}
if (p != NULL)
*p = cpu_to_be32(clock);
+ p = ft_get_prop(blob, "/qe@e0080000/" OF_CPU "/bus-frequency", &len);
+ if (p != NULL)
+ *p = cpu_to_be32(clock);
+
p = ft_get_prop(blob, "/" OF_SOC "/serial@4500/clock-frequency", &len);
if (p != NULL)
*p = cpu_to_be32(clock);
#if defined(CONFIG_MPC85XX_TSEC1)
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/mac-address", &len);
+ if (p)
+ memcpy(p, bd->bi_enetaddr, 6);
+
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/local-mac-address", &len);
+ if (p)
memcpy(p, bd->bi_enetaddr, 6);
#endif
#if defined(CONFIG_HAS_ETH1)
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/mac-address", &len);
+ if (p)
+ memcpy(p, bd->bi_enet1addr, 6);
+
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/local-mac-address", &len);
+ if (p)
memcpy(p, bd->bi_enet1addr, 6);
#endif
#if defined(CONFIG_HAS_ETH2)
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@26000/mac-address", &len);
+ if (p)
+ memcpy(p, bd->bi_enet2addr, 6);
+
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@26000/local-mac-address", &len);
+ if (p)
memcpy(p, bd->bi_enet2addr, 6);
#endif
#if defined(CONFIG_HAS_ETH3)
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@27000/mac-address", &len);
+ if (p)
+ memcpy(p, bd->bi_enet3addr, 6);
+
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@27000/local-mac-address", &len);
+ if (p)
memcpy(p, bd->bi_enet3addr, 6);
#endif
memctl->br1 = CFG_BR1_PRELIM;
#endif
-#if !defined(CONFIG_MPC85xx)
#if defined(CFG_BR2_PRELIM) && defined(CFG_OR2_PRELIM)
memctl->or2 = CFG_OR2_PRELIM;
memctl->br2 = CFG_BR2_PRELIM;
#endif
-#endif
#if defined(CFG_BR3_PRELIM) && defined(CFG_OR3_PRELIM)
memctl->or3 = CFG_OR3_PRELIM;
pcix->powbar1 = (CFG_PCI1_MEM_PHYS >> 12) & 0x000fffff;
pcix->powbear1 = 0x00000000;
pcix->powar1 = (POWAR_EN | POWAR_MEM_READ |
- POWAR_MEM_WRITE | POWAR_MEM_512M);
+ POWAR_MEM_WRITE | (__ilog2(CFG_PCI1_MEM_SIZE) - 1));
pcix->potar2 = (CFG_PCI1_IO_BASE >> 12) & 0x000fffff;
pcix->potear2 = 0x00000000;
pcix->powbar2 = (CFG_PCI1_IO_PHYS >> 12) & 0x000fffff;
pcix->powbear2 = 0x00000000;
pcix->powar2 = (POWAR_EN | POWAR_IO_READ |
- POWAR_IO_WRITE | POWAR_IO_1M);
+ POWAR_IO_WRITE | (__ilog2(CFG_PCI1_IO_SIZE) - 1));
pcix->pitar1 = 0x00000000;
pcix->piwbar1 = 0x00000000;
pcix2->powbar1 = (CFG_PCI2_MEM_PHYS >> 12) & 0x000fffff;
pcix2->powbear1 = 0x00000000;
pcix2->powar1 = (POWAR_EN | POWAR_MEM_READ |
- POWAR_MEM_WRITE | POWAR_MEM_512M);
+ POWAR_MEM_WRITE | (__ilog2(CFG_PCI2_MEM_SIZE) - 1));
pcix2->potar2 = (CFG_PCI2_IO_BASE >> 12) & 0x000fffff;
pcix2->potear2 = 0x00000000;
pcix2->powbar2 = (CFG_PCI2_IO_PHYS >> 12) & 0x000fffff;
pcix2->powbear2 = 0x00000000;
pcix2->powar2 = (POWAR_EN | POWAR_IO_READ |
- POWAR_IO_WRITE | POWAR_IO_1M);
+ POWAR_IO_WRITE | (__ilog2(CFG_PCI2_IO_SIZE) - 1));
pcix2->pitar1 = 0x00000000;
pcix2->piwbar1 = 0x00000000;
}
/*
- * Adjust DDR II IO voltage biasing. It just makes it work.
+ * Adjust DDR II IO voltage biasing.
+ * Only 8548 rev 1 needs the fix
*/
- if (spd.mem_type == SPD_MEMTYPE_DDR2) {
- gur->ddrioovcr = (0
- | 0x80000000 /* Enable */
- | 0x10000000 /* VSEL to 1.8V */
- );
+ if ((SVR_VER(get_svr()) == SVR_8548_E) &&
+ (SVR_MJREV(get_svr()) == 1) &&
+ (spd.mem_type == SPD_MEMTYPE_DDR2)) {
+ gur->ddrioovcr = (0x80000000 /* Enable */
+ | 0x10000000);/* VSEL to 1.8V */
}
/*
* Is this an ECC DDR chip?
* But don't mess with it if the DDR controller will init mem.
*/
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+#ifdef CONFIG_DDR_ECC
if (spd.config == 0x02) {
+#ifndef CONFIG_ECC_INIT_VIA_DDRCONTROLLER
ddr->err_disable = 0x0000000d;
+#endif
ddr->err_sbe = 0x00ff0000;
}
+
debug("DDR: err_disable = 0x%08x\n", ddr->err_disable);
debug("DDR: err_sbe = 0x%08x\n", ddr->err_sbe);
-#endif
+#endif /* CONFIG_DDR_ECC */
asm("sync;isync;msync");
udelay(500);
break;
case 256:
case 512:
+ tlb_size = BOOKE_PAGESZ_256M;
+ break;
case 1024:
case 2048:
- tlb_size = BOOKE_PAGESZ_256M;
+ if (PVR_VER(get_pvr()) > PVR_VER(PVR_85xx))
+ tlb_size = BOOKE_PAGESZ_1G;
+ else
+ tlb_size = BOOKE_PAGESZ_256M;
break;
default:
puts("DDR: only 16M,32M,64M,128M,256M,512M,1G and 2G are supported.\n");
/*
* The memory was not able to be mapped.
+ * Default to a small size.
*/
- return 0;
+ tlb_size = BOOKE_PAGESZ_64M;
+ memsize=64;
break;
}
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile ccsr_gur_t *gur = &immap->im_gur;
- uint plat_ratio,e500_ratio;
+ uint plat_ratio,e500_ratio,half_freqSystemBus;
plat_ratio = (gur->porpllsr) & 0x0000003e;
plat_ratio >>= 1;
- switch(plat_ratio) {
- case 0x02:
- case 0x03:
- case 0x04:
- case 0x05:
- case 0x06:
- case 0x08:
- case 0x09:
- case 0x0a:
- case 0x0c:
- case 0x10:
- sysInfo->freqSystemBus = plat_ratio * CONFIG_SYS_CLK_FREQ;
- break;
- default:
- sysInfo->freqSystemBus = 0;
- break;
- }
-
+ sysInfo->freqSystemBus = plat_ratio * CONFIG_SYS_CLK_FREQ;
e500_ratio = (gur->porpllsr) & 0x003f0000;
e500_ratio >>= 16;
- switch(e500_ratio) {
- case 0x04:
- sysInfo->freqProcessor = 2*sysInfo->freqSystemBus;
- break;
- case 0x05:
- sysInfo->freqProcessor = 5*sysInfo->freqSystemBus/2;
- break;
- case 0x06:
- sysInfo->freqProcessor = 3*sysInfo->freqSystemBus;
- break;
- case 0x07:
- sysInfo->freqProcessor = 7*sysInfo->freqSystemBus/2;
- break;
- default:
- sysInfo->freqProcessor = 0;
- break;
- }
+
+ /* Divide before multiply to avoid integer
+ * overflow for processor speeds above 2GHz */
+ half_freqSystemBus = sysInfo->freqSystemBus/2;
+ sysInfo->freqProcessor = e500_ratio*half_freqSystemBus;
}
+
int get_clocks (void)
{
sys_info_t sys_info;
*/
bl tlb1_entry
mr r5,r0
- li r1,0x0020 /* max 16 TLB1 plus some TLB0 entries */
- mtctr r1
lwzu r4,0(r5) /* how many TLB1 entries we actually use */
+ mtctr r4
-0: cmpwi r4,0
- beq 1f
- lwzu r0,4(r5)
+0: lwzu r0,4(r5)
lwzu r1,4(r5)
lwzu r2,4(r5)
lwzu r3,4(r5)
msync
tlbwe
isync
- addi r4,r4,-1
bdnz 0b
1:
bl law_entry
mr r6,r0
- li r1,0x0007 /* 8 LAWs, but reserve one for boot-over-rio-or-pci */
- mtctr r1
lwzu r5,0(r6) /* how many windows we actually use */
+ mtctr r5
li r2,0x0c28 /* the first pair is reserved for boot-over-rio-or-pci */
li r1,0x0c30
-0: cmpwi r5,0
- beq 1f
- lwzu r4,4(r6)
+0: lwzu r4,4(r6)
lwzu r3,4(r6)
stwx r4,r7,r2
stwx r3,r7,r1
- addi r5,r5,-1
addi r2,r2,0x0020
addi r1,r1,0x0020
bdnz 0b
#if defined(CONFIG_MPC86XX_TSEC1)
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/mac-address", &len);
- memcpy(p, bd->bi_enetaddr, 6);
+ if (p != NULL)
+ memcpy(p, bd->bi_enetaddr, 6);
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/local-mac-address", &len);
+ if (p)
+ memcpy(p, bd->bi_enetaddr, 6);
#endif
#if defined(CONFIG_MPC86XX_TSEC2)
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/mac-address", &len);
- memcpy(p, bd->bi_enet1addr, 6);
+ if (p != NULL)
+ memcpy(p, bd->bi_enet1addr, 6);
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/local-mac-address", &len);
+ if (p != NULL)
+ memcpy(p, bd->bi_enet1addr, 6);
#endif
#if defined(CONFIG_MPC86XX_TSEC3)
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@26000/mac-address", &len);
- memcpy(p, bd->bi_enet2addr, 6);
+ if (p != NULL)
+ memcpy(p, bd->bi_enet2addr, 6);
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@26000/local-mac-address", &len);
+ if (p != NULL)
+ memcpy(p, bd->bi_enet2addr, 6);
#endif
#if defined(CONFIG_MPC86XX_TSEC4)
p = ft_get_prop(blob, "/" OF_SOC "/ethernet@27000/mac-address", &len);
- memcpy(p, bd->bi_enet3addr, 6);
+ if (p != NULL)
+ memcpy(p, bd->bi_enet3addr, 6);
+ p = ft_get_prop(blob, "/" OF_SOC "/ethernet@27000/local-mac-address", &len);
+ if (p != NULL)
+ memcpy(p, bd->bi_enet3addr, 6);
#endif
}
#define CFG_SUPER_BANK_INTERLEAVING 0
/*
- * Convert picoseconds into clock cycles (rounding up if needed).
+ * Convert picoseconds into DRAM clock cycles (rounding up if needed).
*/
-int
-picos_to_clk(int picos)
+static unsigned int
+picos_to_clk(unsigned int picos)
{
- int clks;
-
- clks = picos / (2000000000 / (get_bus_freq(0) / 1000));
- if (picos % (2000000000 / (get_bus_freq(0) / 1000)) != 0) {
+ /* use unsigned long long to avoid rounding errors */
+ const unsigned long long ULL_2e12 = 2000000000000ULL;
+ unsigned long long clks;
+ unsigned long long clks_temp;
+
+ if (! picos)
+ return 0;
+
+ clks = get_bus_freq(0) * (unsigned long long) picos;
+ clks_temp = clks;
+ clks = clks / ULL_2e12;
+ if (clks_temp % ULL_2e12) {
clks++;
}
- return clks;
+ if (clks > 0xFFFFFFFFULL) {
+ clks = 0xFFFFFFFFULL;
+ }
+
+ return (unsigned int) clks;
}
bl setup_ccsrbar
#endif
- /* Fix for SMP linux - Changing arbitration to round-robin */
- lis r3, CFG_CCSRBAR@h
- ori r3, r3, 0x1000
- xor r4, r4, r4
- li r4, 0x1000
- stw r4, 0(r3)
- /* setup the law entries */
- bl law_entry
+ /* -- MPC8641 Rev 1.0 MCM Errata fixups -- */
+
+ /* skip fixups if not Rev 1.0 */
+ mfspr r4, SVR
+ rlwinm r4,r4,0,24,31
+ cmpwi r4,0x10
+ bne 1f
+
+ lis r3,MCM_ABCR@ha
+ lwz r4,MCM_ABCR@l(r3) /* ABCR -> r4 */
+
+ /* set ABCR[A_STRM_CNT] = 0 */
+ rlwinm r4,r4,0,0,29
+
+ /* set ABCR[ARB_POLICY] to 0x1 (round-robin) */
+ addi r0,r0,1
+ rlwimi r4,r0,12,18,19
+
+ stw r4,MCM_ABCR@l(r3) /* r4 -> ABCR */
sync
- /* Don't use this feature due to bug in 8641D PD4 */
- /* Disable ERD_DIS */
- lis r3, CFG_CCSRBAR@h
- ori r3, r3, 0x1008
- lwz r4, 0(r3)
+ /* Set DBCR[ERD_DIS] */
+ lis r3,MCM_DBCR@ha
+ lwz r4,MCM_DBCR@l(r3)
oris r4, r4, 0x4000
- stw r4, 0(r3)
+ stw r4,MCM_DBCR@l(r3)
+ sync
+1:
+ /* setup the law entries */
+ bl law_entry
sync
+
#if (EMULATOR_RUN == 1)
/* On the emulator we want to adjust these ASAP */
/* otherwise things are sloooow */
int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
{
unsigned long zmiifer=0x0;
+ unsigned long pfc1;
- /*
- * Right now only 2*RGMII is supported. Please extend when needed.
- * sr - 2006-08-29
- */
- switch (1) {
- case 0:
+ mfsdr(sdr_pfc1, pfc1);
+ pfc1 &= SDR0_PFC1_SELECT_MASK;
+
+ switch (pfc1) {
+ case SDR0_PFC1_SELECT_CONFIG_2:
/* 1 x GMII port */
out32 (ZMII_FER, 0x00);
out32 (RGMII_FER, 0x00000037);
bis->bi_phymode[0] = BI_PHYMODE_GMII;
bis->bi_phymode[1] = BI_PHYMODE_NONE;
break;
- case 1:
+ case SDR0_PFC1_SELECT_CONFIG_4:
/* 2 x RGMII ports */
out32 (ZMII_FER, 0x00);
out32 (RGMII_FER, 0x00000055);
bis->bi_phymode[0] = BI_PHYMODE_RGMII;
bis->bi_phymode[1] = BI_PHYMODE_RGMII;
break;
- case 2:
+ case SDR0_PFC1_SELECT_CONFIG_6:
/* 2 x SMII ports */
-
+ out32 (ZMII_FER,
+ ((ZMII_FER_SMII) << ZMII_FER_V(0)) |
+ ((ZMII_FER_SMII) << ZMII_FER_V(1)));
+ out32 (RGMII_FER, 0x00000000);
+ bis->bi_phymode[0] = BI_PHYMODE_SMII;
+ bis->bi_phymode[1] = BI_PHYMODE_SMII;
+ break;
+ case SDR0_PFC1_SELECT_CONFIG_1_2:
+ /* only 1 x MII supported */
+ out32 (ZMII_FER, (ZMII_FER_MII) << ZMII_FER_V(0));
+ out32 (RGMII_FER, 0x00000000);
+ bis->bi_phymode[0] = BI_PHYMODE_MII;
+ bis->bi_phymode[1] = BI_PHYMODE_NONE;
break;
default:
break;
#if (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined(CFG_NAND_LEGACY) && \
(defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX))
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_405EZ))
#include <nand.h>
#include <linux/mtd/ndfc.h>
#include <asm/processor.h>
-#include <ppc440.h>
+#include <ppc4xx.h>
static u8 hwctl = 0;
/*
* Setup EBC (CS0 only right now)
*/
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xb8400000);
+ mtebc(EBC0_CFG, 0xb8400000);
mtebc(pb0cr, CFG_EBC_PB0CR);
mtebc(pb0ap, CFG_EBC_PB0AP);
mtdcr ocmdscr2, r3 /* Set Data Side */
mtdcr ocmiscr2, r3 /* Set Instruction Side */
addis r3,0,0x0800 /* OCM Data Parity Disable - 1 Wait State */
- mtdcr ocmdsisdpc,r4
+ mtdcr ocmdsisdpc,r3
isync
#else /* CONFIG_405EZ */
--- /dev/null
+Freescale MPC8313ERDB Board
+-----------------------------------------
+
+1. Board Switches and Jumpers
+
+ SW3 is used to set CFG_RESET_SOURCE.
+
+ To boot the image at 0xFE000000 in NOR flash, use these DIP
+ switche settings for SW3 SW4:
+
+ +------+ +------+
+ | | | **** |
+ | **** | | |
+ +------+ ON +------+ ON
+ 4321 4321
+ (where the '*' indicates the position of the tab of the switch.)
+
+2. Memory Map
+ The memory map looks like this:
+
+ 0x0000_0000 0x07ff_ffff DDR 128M
+ 0x8000_0000 0x8fff_ffff PCI MEM 256M
+ 0x9000_0000 0x9fff_ffff PCI_MMIO 256M
+ 0xe000_0000 0xe00f_ffff IMMR 1M
+ 0xe200_0000 0xe20f_ffff PCI IO 16M
+ 0xe280_0000 0xe280_7fff NAND FLASH (CS1) 32K
+ 0xf000_0000 0xf001_ffff VSC7385 (CS2) 128K
+ 0xfa00_0000 0xfa00_7fff Board Status/ 32K
+ LED Control (CS3)
+ 0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M
+
+3. Definitions
+
+3.1 Explanation of NEW definitions in:
+
+ include/configs/MPC8313ERDB.h
+
+ CONFIG_MPC83xx MPC83xx family
+ CONFIG_MPC831x MPC831x specific
+ CONFIG_MPC8313ERDB MPC8313ERDB board specific
+
+4. Compilation
+
+ Assuming you're using BASH (or similar) as your shell:
+
+ export CROSS_COMPILE=your-cross-compiler-prefix-
+ make distclean
+ make MPC8313ERDB_33_config
+ (or make MPC8313ERDB_66_config, depending on the speed of
+ the oscillator on your board)
+ make
+
+5. Downloading and Flashing Images
+
+5.1 Reflash U-boot Image using U-boot
+
+ =>run tftpflash
+
+ You may want to try
+ =>tftpboot $loadaddr $uboot
+ first, to make sure that the TFTP load will succeed before it
+ goes ahead and wipes out your current firmware. And of course,
+ have an alternate means of programming the flash available
+ if the new u-boot doesn't boot.
+
+5.2 Downloading and Booting Linux Kernel
+
+ Ensure that all networking-related environment variables are set
+ properly (including ipaddr, serverip, gatewayip (if needed),
+ netmask, ethaddr, eth1addr, rootpath (if using NFS root),
+ fdtfile, and bootfile).
+
+ Then, do one of the following, depending on whether you
+ want an NFS root or a ramdisk root:
+
+ =>run nfsboot
+ or
+ =>run ramboot
+
+6 Notes
+
+ Booting from NAND flash is not yet supported.
+ The console baudrate for MPC8313ERDB is 115200bps.
to only board-specific files and - unfortunately - to the DoC code
(see below). A new configuration variable has been introduced:
CFG_NAND_LEGACY, which has to be defined in the board config file if
-that board uses legacy code. If CFG_NAND_LEGACY is defined, the board
-specific config.mk file should also have "BOARDLIBS =
-drivers/nand_legacy/libnand_legacy.a". For boards using the new NAND
-approach (PPChameleon and netstar at the moment) no variable is
-necessary, but the config.mk should have "BOARDLIBS =
-drivers/nand/libnand.a".
+that board uses legacy code.
The necessary changes have been made to all affected boards, and no
build breakage has been introduced, except for NETTA and NETTA_ISDN
+++ /dev/null
-The port was tested on Wind River System Sbc8560 board <www.windriver.com>.
-U-Boot was installed on the flash memory of the CPU card (no the SODIMM).
-
-NOTE: Please configure uboot compile to the proper PCI frequency and
-setup the appropriate DIP switch settings.
-
-SBC8560 board:
-
-Make sure boards switches are set to their appropriate conditions.
-Refer to the Engineering Reference Guide ERG-00300-002. Of particular
-importance are: 1)Tthe settings for JP4 (JP4 1-3 and 2-4), which
-select the on-board FLASH device (Intel 28F128Jx); 2) The settings
-for the Clock SW9 (33 MHz or 66 MHz).
-
- Note: SW9 Settings: 66 MHz
- 4:1 ratio CCB clocks:SYSCLK
- 3:1 ration e500 Core:CCB
- pos1 - on, pos2 - on, pos3 - off, pos4 - on, pos5 - off, pos6 - on
- Note: SW9 Settings: 33 MHz
- 8:1 ratio CCB clocks:SYSCLK
- 3:1 ration e500 Core:CCB
- pos1 - on, pos2 - on, pos3 - on, pos4 - off, pos5 - off, pos6 - on
-
-
-Flashing the FLASH device with the "Wind River ICE":
-
-1) Properly connect and configure the Wind River ICE to the
- target JTAG port. This includes running the SBC8560 register script.
- Make sure target memory can be read and written.
-
-2) Build the u-boot image:
- make distclean
- make SBC8560_66_config or SBC8560_33_config
- make CROSS_COMPILE=.../ELDK3.0/ppc_8xx-/ all
-
- Note: reference is made to the ELDK3.0 compiler but any 85xx cross-compiler
- should suffice.
-
-3) Convert the uboot (.elf) file to a uboot.bin file (using visionClick converter).
- The bin file should be converted from fffc0000 to ffffffff
-
-4) Setup the Flash Utility (tools menu) for:
-
- Determine the clock speed of the PCI bus and set SW9 accordingly
- Note: the speed of the PCI bus defaults to the slowest PCI card
- PlayBack the "default" register file for the SBC8560
- Select the uboot.bin file with zero bias
- Select the initialize Target prior to programming
- Select the V28F640Jx (8192 x 8) 1 device FLASH Algorithm
- Select the erase base address from FFFC0000 to FFFFFFFF
- Select the start address from 0 with size of 4000
-
-5) Erase and Program
struct nand_chip *this = mtd->priv;
u16 bad;
+ page = (int)(ofs >> this->page_shift) & this->pagemask;
+
if (getchip) {
- page = (int)(ofs >> this->page_shift);
chipnr = (int)(ofs >> this->chip_shift);
/* Grab the lock and see if the device is available */
/* Select the NAND device */
this->select_chip(mtd, chipnr);
- } else
- page = (int) ofs;
+ }
if (this->options & NAND_BUSWIDTH_16) {
- this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos & 0xFE, page & this->pagemask);
+ this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos & 0xFE, page);
bad = cpu_to_le16(this->read_word(mtd));
if (this->badblockpos & 0x1)
bad >>= 1;
if ((bad & 0xFF) != 0xff)
res = 1;
} else {
- this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos, page & this->pagemask);
+ this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos, page);
if (this->read_byte(mtd) != 0xff)
res = 1;
}
void pciauto_region_init(struct pci_region* res)
{
- res->bus_lower = res->bus_start;
+ /*
+ * Avoid allocating PCI resources from address 0 -- this is illegal
+ * according to PCI 2.1 and moreover, this is known to cause Linux IDE
+ * drivers to fail. Use a reasonable starting value of 0x1000 instead.
+ */
+ res->bus_lower = res->bus_start ? res->bus_start : 0x1000;
}
void pciauto_region_align(struct pci_region *res, unsigned long size)
int smc_get_ethaddr (bd_t * bd)
{
int env_size, rom_valid, env_present = 0, reg;
- char *s = NULL, *e, *v_mac, es[] = "11:22:33:44:55:66";
+ char *s = NULL, *e, es[] = "11:22:33:44:55:66";
char s_env_mac[64];
- uchar v_env_mac[6], v_rom_mac[6];
+ uchar v_env_mac[6], v_rom_mac[6], *v_mac;
env_size = getenv_r ("ethaddr", s_env_mac, sizeof (s_env_mac));
if ((env_size > 0) && (env_size < sizeof (es))) { /* exit if env is bad */
if (!env_present) { /* if NO env */
if (rom_valid) { /* but ROM is valid */
- v_mac = (char *)v_rom_mac;
+ v_mac = v_rom_mac;
sprintf (s_env_mac, "%02X:%02X:%02X:%02X:%02X:%02X",
v_mac[0], v_mac[1], v_mac[2], v_mac[3],
v_mac[4], v_mac[5]);
return (-1);
}
} else { /* good env, don't care ROM */
- v_mac = (char *)v_env_mac; /* always use a good env over a ROM */
+ v_mac = v_env_mac; /* always use a good env over a ROM */
}
if (env_present && rom_valid) { /* if both env and ROM are good */
/* Write sector count | ReadMemCardData. */
ace_writew((trans & 0xff) | 0x0300, 0x14);
+/*
+ * For FPGA configuration via SystemACE is reset unacceptable
+ * CFGDONE bit in STATUSREG is not set to 1.
+ */
+#ifndef SYSTEMACE_CONFIG_FPGA
/* Reset the configruation controller */
val = ace_readw(0x18);
val |= 0x0080;
ace_writew(val, 0x18);
+#endif
retry = trans * 16;
while (retry > 0) {
* terms of the GNU Public License, Version 2, incorporated
* herein by reference.
*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004, 2007 Freescale Semiconductor, Inc.
* (C) Copyright 2003, Motorola, Inc.
* author Andy Fleming
*
*/
static struct tsec_info_struct tsec_info[] = {
#if defined(CONFIG_MPC85XX_TSEC1) || defined(CONFIG_MPC83XX_TSEC1)
+#if defined(CONFIG_MPC8544DS)
+ {TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX},
+#else
{TSEC1_PHY_ADDR, TSEC_GIGABIT, TSEC1_PHYIDX},
+#endif
#elif defined(CONFIG_MPC86XX_TSEC1)
{TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX},
#else
return 0;
}
+/* Generic function which updates the speed and duplex. If
+ * autonegotiation is enabled, it uses the AND of the link
+ * partner's advertised capabilities and our advertised
+ * capabilities. If autonegotiation is disabled, we use the
+ * appropriate bits in the control register.
+ *
+ * Stolen from Linux's mii.c and phy_device.c
+ */
+uint mii_parse_link(uint mii_reg, struct tsec_private *priv)
+{
+ /* We're using autonegotiation */
+ if (mii_reg & PHY_BMSR_AUTN_ABLE) {
+ uint lpa = 0;
+ uint gblpa = 0;
+
+ /* Check for gigabit capability */
+ if (mii_reg & PHY_BMSR_EXT) {
+ /* We want a list of states supported by
+ * both PHYs in the link
+ */
+ gblpa = read_phy_reg(priv, PHY_1000BTSR);
+ gblpa &= read_phy_reg(priv, PHY_1000BTCR) << 2;
+ }
+
+ /* Set the baseline so we only have to set them
+ * if they're different
+ */
+ priv->speed = 10;
+ priv->duplexity = 0;
+
+ /* Check the gigabit fields */
+ if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) {
+ priv->speed = 1000;
+
+ if (gblpa & PHY_1000BTSR_1000FD)
+ priv->duplexity = 1;
+
+ /* We're done! */
+ return 0;
+ }
+
+ lpa = read_phy_reg(priv, PHY_ANAR);
+ lpa &= read_phy_reg(priv, PHY_ANLPAR);
+
+ if (lpa & (PHY_ANLPAR_TXFD | PHY_ANLPAR_TX)) {
+ priv->speed = 100;
+
+ if (lpa & PHY_ANLPAR_TXFD)
+ priv->duplexity = 1;
+
+ } else if (lpa & PHY_ANLPAR_10FD)
+ priv->duplexity = 1;
+ } else {
+ uint bmcr = read_phy_reg(priv, PHY_BMCR);
+
+ priv->speed = 10;
+ priv->duplexity = 0;
+
+ if (bmcr & PHY_BMCR_DPLX)
+ priv->duplexity = 1;
+
+ if (bmcr & PHY_BMCR_1000_MBPS)
+ priv->speed = 1000;
+ else if (bmcr & PHY_BMCR_100_MBPS)
+ priv->speed = 100;
+ }
+
+ return 0;
+}
+
/*
* Parse the BCM54xx status register for speed and duplex information.
* The linux sungem_phy has this information, but in a table format.
/* Start up the PHY */
if(priv->phyinfo)
phy_run_commands(priv, priv->phyinfo->startup);
+
adjust_link(dev);
/* Enable Transmit and Receive */
{miim_end,}
},
};
+/* a generic flavor. */
+struct phy_info phy_info_generic = {
+ 0,
+ "Unknown/Generic PHY",
+ 32,
+ (struct phy_cmd[]) { /* config */
+ {PHY_BMCR, PHY_BMCR_RESET, NULL},
+ {PHY_BMCR, PHY_BMCR_AUTON|PHY_BMCR_RST_NEG, NULL},
+ {miim_end,}
+ },
+ (struct phy_cmd[]) { /* startup */
+ {PHY_BMSR, miim_read, NULL},
+ {PHY_BMSR, miim_read, &mii_parse_sr},
+ {PHY_BMSR, miim_read, &mii_parse_link},
+ {miim_end,}
+ },
+ (struct phy_cmd[]) { /* shutdown */
+ {miim_end,}
+ }
+};
+
uint mii_parse_lxt971_sr2(uint mii_reg, struct tsec_private *priv)
{
&phy_info_lxt971,
&phy_info_VSC8244,
&phy_info_dp83865,
+ &phy_info_generic,
NULL
};
* terms of the GNU Public License, Version 2, incorporated
* herein by reference.
*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004, 2007 Freescale Semiconductor, Inc.
* (C) Copyright 2003, Motorola, Inc.
* maintained by Xianghua Xiao (x.xiao@motorola.com)
* author Andy Fleming
#define ECNTRL_INIT_SETTINGS 0x00001000
#define ECNTRL_TBI_MODE 0x00000020
#define ECNTRL_R100 0x00000008
+#define ECNTRL_SGMII_MODE 0x00000002
#define miim_end -2
#define miim_read -1
long zlib_decompress(unsigned char *data_in, unsigned char *cpage_out,
__u32 srclen, __u32 destlen)
{
- return (decompress_block(cpage_out, data_in + 2, ldr_memcpy));
+ return (decompress_block(cpage_out, data_in + 2, (void *) ldr_memcpy));
}
--- /dev/null
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* FSL macros */
+#define NGET(val, fslnum) \
+ __asm__ __volatile__ ("nget %0, rfsl" #fslnum :"=r" (val));
+
+#define GET(val, fslnum) \
+ __asm__ __volatile__ ("get %0, rfsl" #fslnum :"=r" (val));
+
+#define NCGET(val, fslnum) \
+ __asm__ __volatile__ ("ncget %0, rfsl" #fslnum :"=r" (val));
+
+#define CGET(val, fslnum) \
+ __asm__ __volatile__ ("cget %0, rfsl" #fslnum :"=r" (val));
+
+#define NPUT(val, fslnum) \
+ __asm__ __volatile__ ("nput %0, rfsl" #fslnum ::"r" (val));
+
+#define PUT(val, fslnum) \
+ __asm__ __volatile__ ("put %0, rfsl" #fslnum ::"r" (val));
+
+#define NCPUT(val, fslnum) \
+ __asm__ __volatile__ ("ncput %0, rfsl" #fslnum ::"r" (val));
+
+#define CPUT(val, fslnum) \
+ __asm__ __volatile__ ("cput %0, rfsl" #fslnum ::"r" (val));
+
+/* CPU dependent */
+/* machine status register */
+#define MFS(val, reg) \
+ __asm__ __volatile__ ("mfs %0," #reg :"=r" (val));
+
+#define MTS(val, reg) \
+ __asm__ __volatile__ ("mts " #reg ", %0"::"r" (val));
+
+/* get return address from interrupt */
+#define R14(val) \
+ __asm__ __volatile__ ("addi %0, r14, 0":"=r" (val));
+
+#define NOP __asm__ __volatile__ ("nop");
+
+/* use machine status registe USE_MSR_REG */
+#ifdef XILINX_USE_MSR_INSTR
+#define MSRSET(val) \
+ __asm__ __volatile__ ("msrset r0," #val );
+
+#define MSRCLR(val) \
+ __asm__ __volatile__ ("msrclr r0," #val );
+
+#else
+#define MSRSET(val) \
+{ \
+ register unsigned tmp; \
+ __asm__ __volatile__ (" \
+ mfs %0, rmsr; \
+ ori %0, %0, "#val"; \
+ mts rmsr, %0; \
+ nop;" \
+ : "=r" (tmp) \
+ : "d" (val) \
+ : "memory"); \
+}
+
+#define MSRCLR(val) \
+{ \
+ register unsigned tmp; \
+ __asm__ __volatile__ (" \
+ mfs %0, rmsr; \
+ andi %0, %0, ~"#val"; \
+ mts rmsr, %0; \
+ nop;" \
+ : "=r" (tmp) \
+ : "d" (val) \
+ : "memory"); \
+}
+#endif
void *arg;
int count; /* number of interrupt */
};
+
+void install_interrupt_handler (int irq, interrupt_handler_t * hdlr,
+ void *arg);
#ifndef __E300_H__
#define __E300_H__
-/*
- * e300 Processor Version & Revision Numbers
- */
-#define PVR_83xx 0x80830000
-#define PVR_8349_REV10 (PVR_83xx | 0x0010)
-#define PVR_8349_REV11 (PVR_83xx | 0x0011)
-#define PVR_8360_REV10 (PVR_83xx | 0x0020)
-#define PVR_8360_REV11 (PVR_83xx | 0x0020)
-
-#if defined(CONFIG_MPC832X)
-#undef PVR_83xx
-#define PVR_83xx 0x80840000
-#endif
+#define PVR_E300C1 0x80830000
+#define PVR_E300C2 0x80840000
+#define PVR_E300C3 0x80850000
/*
* Hardware Implementation-Dependent Register 0 (HID0)
#if defined(CONFIG_MPC83XX)
/* There are other clocks in the MPC83XX */
u32 csb_clk;
-#if defined (CONFIG_MPC834X)
+#if defined (CONFIG_MPC834X) || defined(CONFIG_MPC831X)
u32 tsec1_clk;
u32 tsec2_clk;
- u32 usbmph_clk;
u32 usbdr_clk;
+#endif
+#if defined (CONFIG_MPC834X)
+ u32 usbmph_clk;
#endif /* CONFIG_MPC834X */
u32 core_clk;
u32 i2c1_clk;
u32 pmccr; /* PMC Configuration Register */
u32 pmcer; /* PMC Event Register */
u32 pmcmr; /* PMC Mask Register */
- u8 res0[0xF4];
+ u32 pmccr1; /* PMC Configuration Register 1 */
+ u32 pmccr2; /* PMC Configuration Register 2 */
+ u8 res0[0xEC];
} pmc83xx_t;
/*
u8 res2[0x8];
u32 mrtpr; /* Memory Refresh Timer Prescaler Register */
u32 mdr; /* UPM Data Register */
- u8 res3[0x8];
+ u8 res3[0x4];
+ u32 lsor; /* Special Operation Initiation Register */
u32 lsdmr; /* SDRAM Mode Register */
u8 res4[0x8];
u32 lurt; /* UPM Refresh Timer */
u8 res6[0xC];
u32 lbcr; /* Configuration Register */
u32 lcrr; /* Clock Ratio Register */
- u8 res7[0x28];
- u8 res8[0xF00];
+ u8 res7[0x8];
+ u32 fmr; /* Flash Mode Register */
+ u32 fir; /* Flash Instruction Register */
+ u32 fcr; /* Flash Command Register */
+ u32 fbar; /* Flash Block Addr Register */
+ u32 fpar; /* Flash Page Addr Register */
+ u32 fbcr; /* Flash Byte Count Register */
+ u8 res8[0xF08];
} lbus83xx_t;
/*
* USB
*/
typedef struct usb83xx {
- u8 fixme[0x2000];
+ u8 fixme[0x1000];
} usb83xx_t;
/*
ios83xx_t ios; /* Sequencer */
pcictrl83xx_t pci_ctrl[2]; /* PCI Controller Control and Status Registers */
u8 res5[0x19900];
- usb83xx_t usb;
+ usb83xx_t usb[2];
+ tsec83xx_t tsec[2];
+ u8 res6[0xA000];
+ security83xx_t security;
+ u8 res7[0xC0000];
+} immap_t;
+
+#elif defined(CONFIG_MPC831X)
+typedef struct immap {
+ sysconf83xx_t sysconf; /* System configuration */
+ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */
+ rtclk83xx_t rtc; /* Real Time Clock Module Registers */
+ rtclk83xx_t pit; /* Periodic Interval Timer */
+ gtm83xx_t gtm[2]; /* Global Timers Module */
+ ipic83xx_t ipic; /* Integrated Programmable Interrupt Controller */
+ arbiter83xx_t arbiter; /* System Arbiter Registers */
+ reset83xx_t reset; /* Reset Module */
+ clk83xx_t clk; /* System Clock Module */
+ pmc83xx_t pmc; /* Power Management Control Module */
+ gpio83xx_t gpio[1]; /* General purpose I/O module */
+ u8 res0[0x1300];
+ ddr83xx_t ddr; /* DDR Memory Controller Memory */
+ fsl_i2c_t i2c[2]; /* I2C Controllers */
+ u8 res1[0x1300];
+ duart83xx_t duart[2]; /* DUART */
+ u8 res2[0x900];
+ lbus83xx_t lbus; /* Local Bus Controller Registers */
+ u8 res3[0x1000];
+ spi83xx_t spi; /* Serial Peripheral Interface */
+ dma83xx_t dma; /* DMA */
+ pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */
+ u8 res4[0x80];
+ ios83xx_t ios; /* Sequencer */
+ pcictrl83xx_t pci_ctrl[1]; /* PCI Controller Control and Status Registers */
+ u8 res5[0x1aa00];
+ usb83xx_t usb[1];
tsec83xx_t tsec[2];
u8 res6[0xA000];
security83xx_t security;
#define BOOKE_PAGESZ_16M 7
#define BOOKE_PAGESZ_64M 8
#define BOOKE_PAGESZ_256M 9
-#define BOOKE_PAGESZ_1GB 10
-#define BOOKE_PAGESZ_4GB 11
+#define BOOKE_PAGESZ_1G 10
+#define BOOKE_PAGESZ_4G 11
#if defined(CONFIG_MPC86xx)
#define LAWBAR_BASE_ADDR 0x00FFFFFF
#define LAWAR_TRGT_IF_PCI1 0x00000000
#define LAWAR_TRGT_IF_PCIX 0x00000000
#define LAWAR_TRGT_IF_PCI2 0x00100000
+#define LAWAR_TRGT_IF_PEX 0x00200000
#define LAWAR_TRGT_IF_LBC 0x00400000
#define LAWAR_TRGT_IF_CCSR 0x00800000
#define LAWAR_TRGT_IF_DDR_INTERLEAVED 0x00B00000
#define HID0_BHTE (1<<2) /* Branch History Table Enable */
#define HID0_BTCD (1<<1) /* Branch target cache disable */
#define SPRN_HID1 0x3F1 /* Hardware Implementation Register 1 */
+#define HID1_RFXE (1<<17) /* Read Fault Exception Enable */
+#define HID1_ASTME (1<<13) /* Address bus streaming mode */
+#define HID1_ABE (1<<12) /* Address broadcast enable */
#define SPRN_IABR 0x3F2 /* Instruction Address Breakpoint Register */
#ifndef CONFIG_BOOKE
#define SPRN_IAC1 0x3F4 /* Instruction Address Compare 1 */
#define SPRN_IVOR15 0x19f /* Interrupt Vector Offset Register 15 */
/* e500 definitions */
-#define SPRN_L1CSR0 0x3f2 /* L1 Cache Control and Status Register 0 */
+#define SPRN_L1CSR0 0x3f2 /* L1 Data Cache Control and Status Register 0 */
+#define L1CSR0_CPE 0x00010000 /* Data Cache Parity Enable */
#define L1CSR0_DCFI 0x00000002 /* Data Cache Flash Invalidate */
#define L1CSR0_DCE 0x00000001 /* Data Cache Enable */
-#define SPRN_L1CSR1 0x3f3 /* L1 Cache Control and Status Register 1 */
+#define SPRN_L1CSR1 0x3f3 /* L1 Instruction Cache Control and Status Register 1 */
+#define L1CSR1_CPE 0x00010000 /* Instruction Cache Parity Enable */
#define L1CSR1_ICFI 0x00000002 /* Instruction Cache Flash Invalidate */
#define L1CSR1_ICE 0x00000001 /* Instruction Cache Enable */
#define SVR_MJREV(svr) (((svr) >> 4) & 0x0F) /* Major SOC design revision indicator */
#define SVR_MNREV(svr) (((svr) >> 0) & 0x0F) /* Minor SOC design revision indicator */
-/* System-On-Chip Version Numbers (version field only) */
-#define SVR_MPC5200 0x8011
/* Processor Version Register */
#define PVR_8260_HIP7R1 0x80822013
#define PVR_8260_HIP7RA 0x80822014
+/*
+ * MPC 52xx
+ */
+#define PVR_5200 0x80822011
+#define PVR_5200B 0x80822014
+
/*
* System Version Register
#define SVR_8560 0x8070
#define SVR_8555 0x8079
#define SVR_8541 0x807A
+#define SVR_8544 0x8034
+#define SVR_8544_E 0x803C
#define SVR_8548 0x8031
#define SVR_8548_E 0x8039
#define SVR_8641 0x8090
+#define SVR_8568_E 0x807D
/* I am just adding a single entry for 8260 boards. I think we may be
#define CFG_CMD_EXT2 0x1000000000000000ULL /* EXT2 Support */
#define CFG_CMD_SNTP 0x2000000000000000ULL /* SNTP support */
#define CFG_CMD_DISPLAY 0x4000000000000000ULL /* Display support */
+#define CFG_CMD_MFSL 0x8000000000000000ULL /* FSL support for Microblaze */
#define CFG_CMD_ALL 0xFFFFFFFFFFFFFFFFULL /* ALL commands */
CFG_CMD_IRQ | \
CFG_CMD_JFFS2 | \
CFG_CMD_KGDB | \
+ CFG_CMD_MFSL | \
CFG_CMD_MII | \
CFG_CMD_MMC | \
CFG_CMD_NAND | \
void ppcSync(void);
void ppcDcbz(unsigned long value);
#endif
+#if defined (CONFIG_MICROBLAZE)
+unsigned short in16(unsigned int);
+void out16(unsigned int, unsigned short value);
+#endif
#if defined (CONFIG_MPC83XX)
void ppcDWload(unsigned int *addr, unsigned int *ret);
int adjust_sdram_tbs_8xx (void);
#if defined(CONFIG_8260)
int prt_8260_clks (void);
-#elif defined(CONFIG_MPC83XX)
-int print_clock_conf(void);
#elif defined(CONFIG_MPC5xxx)
int prt_mpc5xxx_clks (void);
#endif
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet
- * hasn't been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#if defined(CFG_IPBSPEED_133)
-# define CFG_PCISPEED_66 /* define for 66MHz speed */
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
+# define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
# define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
# define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
* IPB Bus clocking configuration.
*/
#if defined(CONFIG_LITE5200B)
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#else
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
#endif /* CONFIG_MPC5200 */
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * mpc8313epb board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1
+#define CONFIG_MPC83XX 1
+#define CONFIG_MPC831X 1
+#define CONFIG_MPC8313 1
+#define CONFIG_MPC8313ERDB 1
+
+#define CONFIG_PCI
+#define CONFIG_83XX_GENERIC_PCI
+
+#ifdef CFG_66MHZ
+#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
+#elif defined(CFG_33MHZ)
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#else
+#error Unknown oscillator frequency.
+#endif
+
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+
+#define CFG_IMMR 0xE0000000
+
+#define CFG_MEMTEST_START 0x00001000
+#define CFG_MEMTEST_END 0x07f00000
+
+/* Early revs of this board will lock up hard when attempting
+ * to access the PMC registers, unless a JTAG debugger is
+ * connected, or some resistor modifications are made.
+ */
+#define CFG_8313ERDB_BROKEN_PMC 1
+
+#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+
+/*
+ * Manually set up DDR parameters, as this board does not
+ * seem to have the SPD connected to I2C.
+ */
+#define CFG_DDR_SIZE 128 /* MB */
+#define CFG_DDR_CONFIG ( CSCONFIG_EN | CSCONFIG_AP \
+ | 0x00040000 /* TODO */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
+ /* 0x80840102 */
+
+#define CFG_DDR_TIMING_3 0x00000000
+#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WRT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_RRT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WWT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
+ | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
+ /* 0x00220802 */
+#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
+ | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+ | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
+ | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
+ | (13 << TIMING_CFG1_REFREC_SHIFT ) \
+ | ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
+ | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
+ | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
+ /* 0x3935d322 */
+#define CFG_DDR_TIMING_2 ( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+ | (31 << TIMING_CFG2_CPO_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
+ | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
+ | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
+ | (10 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+ /* 0x0f9048ca */ /* P9-45,may need tuning */
+#define CFG_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+ | ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+ /* 0x03200064 */
+#if defined(CONFIG_DDR_2T_TIMING)
+#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
+ | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+ | SDRAM_CFG_2T_EN \
+ | SDRAM_CFG_DBW_32 )
+#else
+#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
+ | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+ | SDRAM_CFG_32_BE )
+ /* 0x43080000 */
+#endif
+#define CFG_SDRAM_CFG2 0x00401000;
+/* set burst length to 8 for 32-bit data path */
+#define CFG_DDR_MODE ( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
+ | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
+ /* 0x44400232 */
+#define CFG_DDR_MODE_2 0x8000C000;
+
+#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+ /*0x02000000*/
+#define CFG_DDRCDR_VALUE ( DDRCDR_EN \
+ | DDRCDR_PZ_NOMZ \
+ | DDRCDR_NZ_NOMZ \
+ | DDRCDR_M_ODR )
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
+#define CFG_FLASH_SIZE 8 /* flash size in MB */
+#define CFG_FLASH_EMPTY_INFO /* display empty sectors */
+#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
+
+#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \
+ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
+ BR_V) /* valid */
+#define CFG_OR0_PRELIM ( 0xFF000000 /* 16 MByte */ \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_9 \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD )
+ /* 0xFF006FF7 TODO SLOW 16 MB flash size */
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */
+#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */
+
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 135 /* sectors per device */
+
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#endif
+
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+
+#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_2 /* 0x00010002 */
+#define CFG_LBC_LBCR ( 0x00040000 /* TODO */ \
+ | (0xFF << LBCR_BMT_SHIFT) \
+ | 0xF ) /* 0x0004ff0f */
+
+#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */
+
+/* drivers/nand/nand.c */
+#define CFG_NAND_BASE 0xE2800000 /* 0xF0000000 */
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+
+#define CFG_BR1_PRELIM ( CFG_NAND_BASE \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V ) /* valid */
+#define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR )
+ /* 0xFFFF8396 */
+#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
+#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+
+#define CFG_VSC7385_BASE 0xF0000000
+
+#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */
+#define CFG_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */
+#define CFG_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/
+#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE/* Access window base at VSC7385 base */
+#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */
+
+/* local bus read write buffer mapping */
+#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
+#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
+#define CFG_LBLAWBAR3_PRELIM 0xFA000000
+#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8313@0"
+#define OF_SOC "soc8313@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8313@e0000000/serial@4500"
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
+#define CFG_I2C2_OFFSET 0x3100
+
+/* TSEC */
+#define CFG_TSEC1_OFFSET 0x24000
+#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
+#define CFG_TSEC2_OFFSET 0x25000
+#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
+#define CONFIG_NET_MULTI
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_MMIO_BASE 0x90000000
+#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xE2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+/*
+ * TSEC configuration
+ */
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+#define CONFIG_GMII 1 /* MII PHY management */
+#define CONFIG_MPC83XX_TSEC1 1
+
+#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0"
+#define CONFIG_MPC83XX_TSEC2 1
+#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1"
+#define TSEC1_PHY_ADDR 0x1c
+#define TSEC2_PHY_ADDR 4
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC1"
+
+/*
+ * Configure on-board RTC
+ */
+#define CONFIG_RTC_DS1337
+#define CFG_I2C_RTC_ADDR 0x68
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+ #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+
+/* Address and size of Redundant Environment Sector */
+#else
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CFG_BASE_COMMANDS ( CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_DHCP \
+ | CFG_CMD_I2C \
+ | CFG_CMD_MII \
+ | CFG_CMD_DATE \
+ | CFG_CMD_PCI)
+
+#define CONFIG_CMDLINE_EDITING 1
+
+#define CFG_RAMBOOT_COMMANDS (CFG_BASE_COMMANDS & \
+ ~(CFG_CMD_ENV | CFG_CMD_LOADS))
+
+#if defined(CFG_RAMBOOT)
+#define CONFIG_COMMANDS CFG_RAMBOOT_COMMANDS
+#else
+#define CONFIG_COMMANDS CFG_BASE_COMMANDS
+#endif
+
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 16384
+#define CFG_CACHELINE_SIZE 32
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+
+#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */
+
+#ifdef CFG_66MHZ
+
+/* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */
+/* 0x62040000 */
+#define CFG_HRCW_LOW (\
+ 0x20000000 /* reserved, must be set */ |\
+ HRCWL_DDRCM |\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_CSB_TO_CLKIN_2X1 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#elif defined(CFG_33MHZ)
+
+/* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
+/* 0x65040000 */
+#define CFG_HRCW_LOW (\
+ 0x20000000 /* reserved, must be set */ |\
+ HRCWL_DDRCM |\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_CSB_TO_CLKIN_5X1 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#endif
+
+/* 0xa0606c00 */
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_RGMII |\
+ HRCWH_TSEC2M_IN_RGMII |\
+ HRCWH_BIG_ENDIAN |\
+ HRCWH_LALE_NORMAL)
+
+/* System IO Config */
+#define CFG_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */
+#define CFG_SICRL SICRL_USBDR /* Enable Internal USB Phy */
+
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+
+#define CFG_HID2 HID2_HBE
+
+/* DDR @ 0x00000000 */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI @ 0x80000000 */
+#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10)
+#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI2 not supported on 8313 */
+#define CFG_IBAT3L (0)
+#define CFG_IBAT3U (0)
+#define CFG_IBAT4L (0)
+#define CFG_IBAT4U (0)
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CFG_IBAT6L (0xF0000000 | BATL_PP_10)
+#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT7L (0)
+#define CFG_IBAT7U (0)
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ETHADDR 00:E0:0C:00:95:01
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:E0:0C:00:95:02
+
+#define CONFIG_IPADDR 10.0.0.2
+#define CONFIG_SERVERIP 10.0.0.1
+#define CONFIG_GATEWAYIP 10.0.0.1
+#define CONFIG_NETMASK 255.0.0.0
+#define CONFIG_NETDEV eth1
+
+#define CONFIG_HOSTNAME mpc8313erdb
+#define CONFIG_ROOTPATH /nfs/root/path
+#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
+#define CONFIG_FDTFILE mpc8313erdb.dtb
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
+#define CONFIG_BAUDRATE 115200
+
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "ethprime=TSEC1\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
+ "console=ttyS0\0" \
+ "setbootargs=setenv bootargs " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+ "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv rootdev /dev/nfs;" \
+ "run setbootargs;" \
+ "run setipargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv rootdev /dev/ram;" \
+ "run setbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif /* __CONFIG_H */
#define CFG_MEMTEST_START 0x1000 /* memtest region */
#define CFG_MEMTEST_END 0x2000
+#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
+ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
#ifdef CONFIG_HARD_I2C
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
#endif
/*
* General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-
-#define CFG_PCI1_IO_BASE 0x0
+#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe2000000
#define CFG_PCI1_IO_SIZE 0x100000 /* 1M */
/*
* General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
--- /dev/null
+/*
+ * Copyright 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8544ds board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
+#define CONFIG_MPC8544 1
+#define CONFIG_MPC8544DS 1
+
+#undef CONFIG_PCI /* Enable PCI/PCIE */
+#undef CONFIG_PCI1 /* PCI controller 1 */
+#undef CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
+#undef CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
+#undef CONFIG_PCIE3 /* PCIE controler 3 (ULI bridge) */
+#undef CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_DLL
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CONFIG_DDR_ECC_CMD
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the CDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS 1
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00400000
+#define CFG_ALT_MEMTEST
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
+#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
+#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000)
+#define CFG_PCIE3_ADDR (CFG_CCSRBAR+0xb000)
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required")
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
+ *
+ * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
+ *
+ * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
+ *
+ * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable
+ * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
+ *
+ * Localbus cacheable
+ *
+ * 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable
+ * 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0
+ *
+ * Localbus non-cacheable
+ *
+ * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable
+ * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable
+ * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable
+ *
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CFG_BOOT_BLOCK 0xfc000000 /* boot TLB */
+
+#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
+
+#define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */
+
+#define CFG_BR0_PRELIM 0xff801001
+#define CFG_BR1_PRELIM 0xfe801001
+
+#define CFG_OR0_PRELIM 0xff806e65
+#define CFG_OR1_PRELIM 0xff806e65
+
+#define CFG_FLASH_BANKS_LIST {0xfe800000,CFG_FLASH_BASE}
+
+#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#define CFG_LBC_NONCACHE_BASE 0xf8000000
+
+#define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */
+#define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/
+
+#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */
+#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
+
+#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
+#define PIXIS_ID 0x0 /* Board ID at offset 0 */
+#define PIXIS_VER 0x1 /* Board version at offset 1 */
+#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
+#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
+#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch
+ * register */
+#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
+#define PIXIS_VCTL 0x10 /* VELA Control Register */
+#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
+#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
+#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
+#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
+#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
+#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
+
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM 1
+#define CFG_INIT_L1_LOCK 1
+#define CFG_INIT_L1_ADDR 0xf4010000 /* Initial L1 address */
+#define CFG_INIT_L1_END 0x00004000 /* End of used area in RAM */
+
+/* define to use L2SRAM as initial stack */
+#undef CONFIG_L2_INIT_RAM
+#define CFG_INIT_L2_ADDR 0xf8fc0000
+#define CFG_INIT_L2_END 0x00040000 /* End of used area in RAM */
+
+#ifdef CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_ADDR CFG_INIT_L1_ADDR
+#define CFG_INIT_RAM_END CFG_INIT_L1_END
+#else
+#define CFG_INIT_RAM_ADDR CFG_INIT_L2_ADDR
+#define CFG_INIT_RAM_END CFG_INIT_L2_END
+#endif
+
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8544@0"
+#define OF_SOC "soc8544@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8544@e0000000/serial@4500"
+
+/* I2C */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR 0x57
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3100
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CFG_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */
+#define CFG_PCI_PHYS 0xc0000000 /* 512M PCI TLB */
+
+#define CFG_PCI1_MEM_BASE 0xc0000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe1000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
+/* controller 2, Slot 1, tgtid 1, Base address 9000 */
+#define CFG_PCIE2_MEM_BASE 0x80000000
+#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE
+#define CFG_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCIE2_IO_BASE 0x00000000
+#define CFG_PCIE2_IO_PHYS 0xe2000000
+#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */
+
+/* controller 1, Slot 2,tgtid 2, Base address a000 */
+#define CFG_PCIE1_MEM_BASE 0xa0000000
+#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE 0x08000000 /* 128M */
+#define CFG_PCIE1_MEM_BASE2 0xa8000000
+#define CFG_PCIE1_MEM_PHYS2 CFG_PCIE1_MEM_BASE2
+#define CFG_PCIE1_MEM_SIZE2 0x04000000 /* 64M */
+#define CFG_PCIE1_IO_BASE 0x00000000 /* reuse mem LAW */
+#define CFG_PCIE1_IO_PHYS 0xaf000000
+#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
+
+/* controller 3, direct to uli, tgtid 3, Base address b000 */
+#define CFG_PCIE3_MEM_BASE 0xb0000000
+#define CFG_PCIE3_MEM_PHYS CFG_PCIE3_MEM_BASE
+#define CFG_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCIE3_IO_BASE 0x00000000
+#define CFG_PCIE3_IO_PHYS 0xe3000000
+#define CFG_PCIE3_IO_SIZE 0x00100000 /* 1M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#define CONFIG_RTL8139
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x) (x)
+#define _IO_BASE 0x00000000
+#endif
+
+#ifndef CONFIG_PCI_PNP
+ #define PCI_ENET0_IOADDR CFG_PCI1_IO_BASE
+ #define PCI_ENET0_MEMADDR CFG_PCI1_IO_BASE
+ #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID 4
+#define CFG_SCSI_MAX_LUN 1
+#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#endif /* SCSCI */
+
+#endif /* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC1_NAME "eTSEC1"
+#define CONFIG_MPC85XX_TSEC3 1
+#define CONFIG_MPC85XX_TSEC3_NAME "eTSEC3"
+#undef CONFIG_MPC85XX_FEC
+
+#define TSEC1_PHY_ADDR 0
+#define TSEC3_PHY_ADDR 1
+
+#define TSEC1_PHYIDX 0
+#define TSEC3_PHYIDX 0
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#if CFG_MONITOR_BASE > 0xfff80000
+#define CFG_ENV_ADDR 0xfff80000
+#else
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#endif
+#define CFG_ENV_SIZE 0x2000
+#define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#if defined(CONFIG_PCI)
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PCI \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C \
+ | CFG_CMD_MII \
+ | CFG_CMD_BEDBUG \
+ | CFG_CMD_NET)
+#else
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C \
+ | CFG_CMD_MII)
+#endif
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR 00:E0:0C:02:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD
+#endif
+
+#define CONFIG_IPADDR 192.168.1.251
+
+#define CONFIG_HOSTNAME 8544ds_unknown
+#define CONFIG_ROOTPATH /nfs/mpc85xx
+#define CONFIG_BOOTFILE 8544ds_tmt/uImage.uboot
+
+#define CONFIG_SERVERIP 192.168.0.1
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_NETMASK 255.255.0.0
+
+#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE 115200
+
+#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
+#define PCIE_ENV \
+ "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
+ "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
+ "pcie1regs=setenv a e000a; run pciereg\0" \
+ "pcie2regs=setenv a e0009; run pciereg\0" \
+ "pcie3regs=setenv a e000b; run pciereg\0" \
+ "pcieerr=md ${a}020 1; md ${a}e00;" \
+ "pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
+ "pci d.w $b.0 56 1;" \
+ "pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \
+ "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff;" \
+ "pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff;" \
+ "pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \
+ "pci w $b.0 130 ffffffff\0" \
+ "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
+ "pcie1err=setenv a e000a; run pcieerr\0" \
+ "pcie2err=setenv a e0009; run pcieerr\0" \
+ "pcie3err=setenv a e000b; run pcieerr\0" \
+ "pcie1errc=setenv a e000a; run pcieerrc\0" \
+ "pcie2errc=setenv a e0009; run pcieerrc\0" \
+ "pcie3errc=setenv a e000b; run pcieerrc\0"
+#else
+#define PCIE_ENV ""
+#endif
+
+#if defined(CONFIG_PCI1)
+#define PCI_ENV \
+ "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
+ "echo e;md ${a}e00 9\0" \
+ "pci1regs=setenv a e0008; run pcireg\0" \
+ "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
+ "pci d.w $b.0 56 1\0" \
+ "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
+ "pci w.w $b.0 56 ffff\0" \
+ "pci1err=setenv a e0008; run pcierr\0" \
+ "pci1errc=setenv a e0008; run pcierrc\0"
+#else
+#define PCI_ENV ""
+#endif
+
+#if defined(CONFIG_TSEC_ENET)
+#define ENET_ENV \
+ "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \
+ "md ${a}098 2\0" \
+ "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \
+ "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \
+ "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \
+ "echo mib;md ${a}680 31\0" \
+ "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \
+ "enet1regs=setenv a e0024; run enetreg\0" \
+ "enet3regs=setenv a e0026; run enetreg\0"
+#else
+#define ENET_ENV ""
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=8544ds_tmt/ramdisk.uboot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=8544ds_tmt/mpc8544ds.dtb\0" \
+ "eoi=mw e00400b0 0\0" \
+ "iack=md e00400a0 1\0" \
+ "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
+ "md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
+ "ddrregs=setenv a e0002; run ddrreg\0" \
+ "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
+ "md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0" \
+ "guregs=setenv a e00e0; run gureg\0" \
+ "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
+ "ecmregs=setenv a e0001; run ecmreg\0" \
+ PCIE_ENV \
+ PCI_ENV \
+ ENET_ENV
+
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs root=/dev/sda3 rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#endif /* __CONFIG_H */
#define CONFIG_MPC8548 1 /* MPC8548 specific */
#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */
-#undef CONFIG_PCI
+#define CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
/*
* General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */
-#define CFG_PCI2_MEM_BASE 0xa0000000
+#define CFG_PCI2_MEM_BASE 0x90000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe2100000
-#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+#define CFG_PCI2_IO_PHYS 0xe2800000
+#define CFG_PCI2_IO_SIZE 0x00800000 /* 8M */
+#define CFG_PEX_MEM_BASE 0xa0000000
+#define CFG_PEX_MEM_PHYS CFG_PEX_MEM_BASE
+#define CFG_PEX_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PEX_IO_BASE 0x00000000
+#define CFG_PEX_IO_PHYS 0xe3000000
+#define CFG_PEX_IO_SIZE 0x01000000 /* 16M */
+
+/*
+ * RapidIO MMU
+ */
+#define CFG_RIO_MEM_BASE 0xC0000000
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */
#if defined(CONFIG_PCI)
/*
* General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x100000 /* 1M */
#if defined(CONFIG_PCI)
--- /dev/null
+/*
+ * Copyright 2004-2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * mpc8568mds board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */
+#define CONFIG_MPC8568 1 /* MPC8568 specific */
+#define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */
+
+#undef CONFIG_PCI
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+/*#define CONFIG_DDR_2T_TIMING Sets the 2T timing bit */
+
+/*#define CONFIG_DDR_ECC*/ /* only for ECC DDR module */
+/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/ /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+
+/*
+ * When initializing flash, if we cannot find the manufacturer ID,
+ * assume this is the AMD flash associated with the MDS board.
+ * This allows booting from a promjet.
+ */
+#define CONFIG_ASSUME_AMD_FLASH
+
+#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_clock_freq(void);
+#endif /*Replace a call to get_clock_freq (after it is implemented)*/
+#define CONFIG_SYS_CLK_FREQ 66000000 /*TODO: restore if wanting to read from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+/*#define CONFIG_L2_CACHE*/ /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS 1
+
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00400000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+#error ("CONFIG_SPD_EEPROM is required")
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
+/*
+ * Local Bus Definitions
+ */
+
+/*
+ * FLASH on the Local Bus
+ * Two banks, 8M each, using the CFI driver.
+ * Boot from BR0/OR0 bank at 0xff00_0000
+ * Alternate BR1/OR1 bank at 0xff80_0000
+ *
+ * BR0, BR1:
+ * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
+ * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
+ * Port Size = 16 bits = BRx[19:20] = 10
+ * Use GPCM = BRx[24:26] = 000
+ * Valid = BRx[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
+ *
+ * OR0, OR1:
+ * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
+ * Reserved ORx[17:18] = 11, confusion here?
+ * CSNT = ORx[20] = 1
+ * ACS = half cycle delay = ORx[21:22] = 11
+ * SCY = 6 = ORx[24:27] = 0110
+ * TRLX = use relaxed timing = ORx[29] = 1
+ * EAD = use external address latch delay = OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
+ */
+#define CFG_BCSR_BASE 0xf8000000
+
+#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH 32M */
+
+/*Chip select 0 - Flash*/
+#define CFG_BR0_PRELIM 0xfe001001
+#define CFG_OR0_PRELIM 0xfe006ff7
+
+/*Chip slelect 1 - BCSR*/
+#define CFG_BR1_PRELIM 0xf8000801
+#define CFG_OR1_PRELIM 0xffffe9f7
+
+/*#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} */
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 512 /* sectors per device */
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+
+/*
+ * SDRAM on the LocalBus
+ */
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+
+/*Chip select 2 - SDRAM*/
+#define CFG_BR2_PRELIM 0xf0001861
+#define CFG_OR2_PRELIM 0xfc006901
+
+#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
+#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
+#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+
+/*
+ * Common settings for all Local Bus SDRAM commands.
+ * At run time, either BSMA1516 (for CPU 1.1)
+ * or BSMA1617 (for CPU 1.0) (old)
+ * is OR'ed in too.
+ */
+#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \
+ | CFG_LBC_LSDMR_PRETOACT7 \
+ | CFG_LBC_LSDMR_ACTTORW7 \
+ | CFG_LBC_LSDMR_BL8 \
+ | CFG_LBC_LSDMR_WRC4 \
+ | CFG_LBC_LSDMR_CL3 \
+ | CFG_LBC_LSDMR_RFEN \
+ )
+
+/*
+ * The bcsr registers are connected to CS3 on MDS.
+ * The new memory map places bcsr at 0xf8000000.
+ *
+ * For BR3, need:
+ * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
+ * port-size = 8-bits = BR[19:20] = 01
+ * no parity checking = BR[21:22] = 00
+ * GPMC for MSEL = BR[24:26] = 000
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
+ *
+ * For OR3, need:
+ * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
+ * disable buffer ctrl OR[19] = 0
+ * CSNT OR[20] = 1
+ * ACS OR[21:22] = 11
+ * XACS OR[23] = 1
+ * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
+ * SETA OR[28] = 0
+ * TRLX OR[29] = 1
+ * EHTR OR[30] = 1
+ * EAD extra time OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
+ */
+#define CFG_BCSR (0xf8000000)
+
+/*Chip slelect 4 - PIB*/
+#define CFG_BR4_PRELIM 0xf8008801
+#define CFG_OR4_PRELIM 0xffffe9f7
+
+/*Chip select 5 - PIB*/
+#define CFG_BR5_PRELIM 0xf8010801
+#define CFG_OR5_PRELIM 0xffff69f7
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser*/
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8568@0"
+#define OF_SOC "soc8568@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8568@e0000000/serial@4600"
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR 0x57
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
+
+/*
+ * General PCI
+ * Memory Addresses are mapped 1-1. I/O is mapped from 0
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */
+
+#define CFG_PEX_MEM_BASE 0xa0000000
+#define CFG_PEX_MEM_PHYS CFG_PEX_MEM_BASE
+#define CFG_PEX_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PEX_IO_BASE 0x00000000
+#define CFG_PEX_IO_PHYS 0xe2800000
+#define CFG_PEX_IO_SIZE 0x00800000 /* 8M */
+
+#define CFG_SRIO_MEM_BASE 0xc0000000
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+#endif /* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC1_NAME "eTSEC0"
+#define CONFIG_MPC85XX_TSEC2 1
+#define CONFIG_MPC85XX_TSEC2_NAME "eTSEC1"
+#undef CONFIG_MPC85XX_TSEC3
+#undef CONFIG_MPC85XX_TSEC4
+#undef CONFIG_MPC85XX_FEC
+
+#define TSEC1_PHY_ADDR 2
+#define TSEC2_PHY_ADDR 3
+
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+
+/* Options are: eTSEC[0-3] */
+#define CONFIG_ETHPRIME "eTSEC0"
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CFG_ENV_SIZE 0x2000
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#if defined(CONFIG_PCI)
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PCI \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C \
+ | CFG_CMD_MII)
+#else
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C \
+ | CFG_CMD_MII)
+#endif
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
+#endif
+
+#define CONFIG_IPADDR 192.168.1.253
+
+#define CONFIG_HOSTNAME unknown
+#define CONFIG_ROOTPATH /nfsroot
+#define CONFIG_BOOTFILE your.uImage
+
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.255.0
+
+#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=600000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=your.fdt.dtb\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs\0" \
+
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "run nfsargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "run ramargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
+
+#endif /* __CONFIG_H */
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
+++ /dev/null
-/*
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * (C) Copyright 2004 Wind River Systems Inc <www.windriver.com>.
- * Added support for Wind River SBC8560 board
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
-/* make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#if XXX
-#define DEBUG /* General debug */
-#define ET_DEBUG
-#endif
-#define TSEC_DEBUG
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
-
-
-#define CONFIG_CPM2 1 /* has CPM2 */
-#define CONFIG_SBC8560 1 /* configuration for SBC8560 board */
-
-#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific (supplement) */
-
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_PCI /* pci ethernet support */
-#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
-
-
-#define CONFIG_ENV_OVERWRITE
-
-/* Using Localbus SDRAM to emulate flash before we can program the flash,
- * normally you need a flash-boot image(u-boot.bin), if so undef this.
- */
-#undef CONFIG_RAM_AS_FLASH
-
-#if defined(CONFIG_PCI_66) /* some PCI card is 33Mhz only */
- #define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */
-#else
- #define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */
-#endif
-
-/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
-
-#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
- defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
- defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC))
-#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
-#endif
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-
-#if XXX
- #define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
-#else
- #define CFG_CCSRBAR 0xff700000 /* default CCSRBAR */
-#endif
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 512 /* DDR is 512MB */
-#define SPD_EEPROM_ADDRESS 0x55 /* DDR DIMM */
-
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-
-#if defined(CONFIG_MPC85xx_REV1)
- #define CONFIG_DDR_DLL /* possible DLL fix needed */
-#endif
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-#if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
- #define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 8M */
- #define CFG_BR0_PRELIM 0xf8000801 /* port size 8bit */
- #define CFG_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */
-#else /* Boot from real Flash */
- #define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
- #define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */
- #define CFG_BR0_PRELIM 0xff800801 /* port size 8bit */
- #define CFG_OR0_PRELIM 0xff800ff7 /* 8MB Flash */
-#endif
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/* local bus definitions */
-#define CFG_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */
-#define CFG_OR1_PRELIM 0xfc000ff7
-
-#define CFG_BR2_PRELIM 0x00000000 /* CS2 not used */
-#define CFG_OR2_PRELIM 0x00000000
-
-#define CFG_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */
-#define CFG_OR3_PRELIM 0xfc000cc1
-
-#if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */
-#else
- #define CFG_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */
-#endif
-#define CFG_OR4_PRELIM 0xfc000cc1
-
-#define CFG_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */
-#if 1
- #define CFG_OR5_PRELIM 0xff000ff7
-#else
- #define CFG_OR5_PRELIM 0xff0000f0
-#endif
-
-#define CFG_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */
-#define CFG_OR6_PRELIM 0xfc000ff7
-#define CFG_LBC_LCRR 0x00030002 /* local bus freq */
-#define CFG_LBC_LBCR 0x00000000
-#define CFG_LBC_LSRT 0x20000000
-#define CFG_LBC_MRTPR 0x20000000
-#define CFG_LBC_LSDMR_1 0x2861b723
-#define CFG_LBC_LSDMR_2 0x0861b723
-#define CFG_LBC_LSDMR_3 0x0861b723
-#define CFG_LBC_LSDMR_4 0x1861b723
-#define CFG_LBC_LSDMR_5 0x4061b723
-
-/* just hijack the MOT BCSR def for SBC8560 misc devices */
-#define CFG_BCSR ((CFG_BR5_PRELIM & 0xff000000)|0x00400000)
-/* the size of CS5 needs to be >= 16M for TLB and LAW setups */
-
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-
-#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK 1843200 /* get_bus_freq(0) */
-#define CONFIG_BAUDRATE 9600
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CFG_NS16550_COM1 ((CFG_BR5_PRELIM & 0xff000000)+0x00700000)
-#define CFG_NS16550_COM2 ((CFG_BR5_PRELIM & 0xff000000)+0x00800000)
-
-/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-
-#define CFG_PCI_MEM_BASE 0xC0000000
-#define CFG_PCI_MEM_PHYS 0xC0000000
-#define CFG_PCI_MEM_SIZE 0x10000000
-
-#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
-
-# define CONFIG_NET_MULTI 1
-# define CONFIG_MII 1 /* MII PHY management */
-# define CONFIG_MPC85xx_TSEC1
-# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0"
-# define TSEC1_PHY_ADDR 25
-# define TSEC1_PHYIDX 0
-/* Options are: TSEC0 */
-# define CONFIG_ETHPRIME "TSEC0"
-
-
-#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
-
- #undef CONFIG_ETHER_NONE /* define if ether on something else */
- #define CONFIG_ETHER_ON_FCC2 /* cpm FCC ethernet support */
- #define CONFIG_ETHER_INDEX 2 /* which channel for ether */
-
- #if (CONFIG_ETHER_INDEX == 2)
- /*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers
- * - Full duplex
- */
- #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CFG_CPMFCR_RAMTYPE 0
- #define CFG_FCC_PSMR (FCC_PSMR_FDE)
-
- #elif (CONFIG_ETHER_INDEX == 3)
- /* need more definitions here for FE3 */
- #endif /* CONFIG_ETHER_INDEX */
-
- #define CONFIG_MII /* MII PHY management */
- #define CONFIG_BITBANGMII /* bit-bang MII PHY management */
- /*
- * GPIO pins used for bit-banged MII communications
- */
- #define MDIO_PORT 2 /* Port C */
- #define MDIO_ACTIVE (iop->pdir |= 0x00400000)
- #define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
- #define MDIO_READ ((iop->pdat & 0x00400000) != 0)
-
- #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
- else iop->pdat &= ~0x00400000
-
- #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
- else iop->pdat &= ~0x00200000
-
- #define MIIDELAY udelay(1)
-
-#endif
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#if 0
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION /* use hardware protection */
-#endif
-#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
-
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-
-#if 0
-/* XXX This doesn't work and I don't want to fix it */
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
- #define CFG_RAMBOOT
-#else
- #undef CFG_RAMBOOT
-#endif
-#endif
-
-/* Environment */
-#if !defined(CFG_RAMBOOT)
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_ENV_IS_NOWHERE
- #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
- #define CFG_ENV_SIZE 0x2000
- #else
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
- #define CFG_ENV_SIZE 0x2000 /* CFG_ENV_SECT_SIZE */
- #endif
-#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=192.168.0.251:/tftpboot ip=192.168.0.105:192.168.0.251::255.255.255.0:sbc8560:eth0:off console=ttyS0,9600"
-/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
-#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000"
-#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV | \
- CFG_CMD_LOADS ))
- #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV))
- #endif
-#else
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C)
- #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C)
- #endif
-#endif
-
-#include <cmd_confdefs.h>
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "SBC8560=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x1000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
- #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/*Note: change below for your network setting!!! */
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-# define CONFIG_ETHADDR 00:vv:ww:xx:yy:8a
-# define CONFIG_HAS_ETH1
-# define CONFIG_ETH1ADDR 00:vv:ww:xx:yy:8b
-# define CONFIG_HAS_ETH2
-# define CONFIG_ETH2ADDR 00:vv:ww:xx:yy:8c
-#endif
-
-#define CONFIG_SERVERIP YourServerIP
-#define CONFIG_IPADDR YourTargetIP
-#define CONFIG_GATEWAYIP YourGatewayIP
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_HOSTNAME SBC8560
-#define CONFIG_ROOTPATH YourRootPath
-#define CONFIG_BOOTFILE YourImageName
-
-#endif /* __CONFIG_H */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133) && !defined(CONFIG_CAM5200)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK) && !defined(CONFIG_CAM5200)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock of
+ * 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
#define CONFIG_ACADIA 1 /* Board is Acadia */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_405EZ 1 /* Specifc 405EZ support*/
-#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */
+/* Detect Acadia PLL input clock automatically via CPLD bit */
+#define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \
+ 66666666 : 33333000)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_F 1 /* Call misc_init_f */
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
-#if 0 /* test-only */
-#define TEST_ONLY_NAND
-#endif
-
-#ifdef TEST_ONLY_NAND
-#define CMD_NAND CFG_CMD_NAND
-#else
-#define CMD_NAND 0
-#endif
-
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
- CMD_NAND | \
+ CFG_CMD_NAND | \
CFG_CMD_NET | \
CFG_CMD_NFS | \
CFG_CMD_PCI | \
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#ifdef TEST_ONLY_NAND
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
#define NAND_MAX_CHIPS 1
#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-#endif
/*-----------------------------------------------------------------------
* Cache Configuration
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
-#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (Flash) initialization */
#define CFG_EBC_PB0AP 0x03337200
/*-----------------------------------------------------------------------
* Definitions for GPIO_0 setup (PPC405EZ specific)
*
- * GPIO0[0-3] - External Bus Controller CS_4 - CS_7 Outputs
+ * GPIO0[0-2] - External Bus Controller CS_4 - CS_6 Outputs
+ * GPIO0[3] - NAND FLASH Controller CE3 (NFCE3) Output
* GPIO0[4] - External Bus Controller Hold Input
* GPIO0[5] - External Bus Controller Priority Input
* GPIO0[6] - External Bus Controller HLDA Output
*/
#define CFG_GPIO0_TCR 0xC0000000
#define CFG_GPIO0_OSRL 0x50000000
-#define CFG_GPIO0_OSRH 0x00000055
+#define CFG_GPIO0_OSRH 0x02000055
#define CFG_GPIO0_ISR1L 0x00000000
#define CFG_GPIO0_ISR1H 0x00000055
-#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TSRL 0x02000000
#define CFG_GPIO0_TSRH 0x00000055
/*-----------------------------------------------------------------------
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
- * (C) Copyright 2005-2006
+ * (C) Copyright 2005-2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* See file CREDITS for list of people who contributed to this
* 2nd ethernet port you have to "undef" the following define.
*/
#define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */
-#define CFG_NAND_LEGACY
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
#endif /* CFG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
- * NAND-FLASH related
+ * NAND FLASH
*----------------------------------------------------------------------*/
-#define NAND_CMD_REG (0x00) /* NandFlash Command Register */
-#define NAND_ADDR_REG (0x04) /* NandFlash Address Register */
-#define NAND_DATA_REG (0x08) /* NandFlash Data Register */
-#define NAND_ECC0_REG (0x10) /* NandFlash ECC Register0 */
-#define NAND_ECC1_REG (0x14) /* NandFlash ECC Register1 */
-#define NAND_ECC2_REG (0x18) /* NandFlash ECC Register2 */
-#define NAND_ECC3_REG (0x1C) /* NandFlash ECC Register3 */
-#define NAND_ECC4_REG (0x20) /* NandFlash ECC Register4 */
-#define NAND_ECC5_REG (0x24) /* NandFlash ECC Register5 */
-#define NAND_ECC6_REG (0x28) /* NandFlash ECC Register6 */
-#define NAND_ECC7_REG (0x2C) /* NandFlash ECC Register7 */
-#define NAND_CR0_REG (0x30) /* NandFlash Device Bank0 Config Register */
-#define NAND_CR1_REG (0x34) /* NandFlash Device Bank1 Config Register */
-#define NAND_CR2_REG (0x38) /* NandFlash Device Bank2 Config Register */
-#define NAND_CR3_REG (0x3C) /* NandFlash Device Bank3 Config Register */
-#define NAND_CCR_REG (0x40) /* NandFlash Core Configuration Register */
-#define NAND_STAT_REG (0x44) /* NandFlash Device Status Register */
-#define NAND_HWCTL_REG (0x48) /* NandFlash Direct Hwd Control Register */
-#define NAND_REVID_REG (0x50) /* NandFlash Core Revision Id Register */
-
-/* Nand Flash K9F1208U0A Command Set => Nand Flash 0 */
-#define NAND0_CMD_READ1_HALF1 0x00 /* Starting addr for 1rst half of registers */
-#define NAND0_CMD_READ1_HALF2 0x01 /* Starting addr for 2nd half of registers */
-#define NAND0_CMD_READ2 0x50
-#define NAND0_CMD_READ_ID 0x90
-#define NAND0_CMD_READ_STATUS 0x70
-#define NAND0_CMD_RESET 0xFF
-#define NAND0_CMD_PAGE_PROG 0x80
-#define NAND0_CMD_PAGE_PROG_TRUE 0x10
-#define NAND0_CMD_PAGE_PROG_DUMMY 0x11
-#define NAND0_CMD_BLOCK_ERASE 0x60
-#define NAND0_CMD_BLOCK_ERASE_END 0xD0
-
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_CMD_REG) = d;} while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_ADDR_REG) = d;} while(0)
-#define WRITE_NAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_DATA_REG) = d;} while(0)
-#define READ_NAND(adr) (*(volatile u8 *)((ulong)adr+NAND_DATA_REG))
-#define NAND_WAIT_READY(nand) while (!(*(volatile u8 *)((ulong)nand->IO_ADDR+NAND_STAT_REG) & 0x01))
-
-/* not needed with 440EP NAND controller */
-#define NAND_CTL_CLRALE(nandptr)
-#define NAND_CTL_SETALE(nandptr)
-#define NAND_CTL_CLRCLE(nandptr)
-#define NAND_CTL_SETCLE(nandptr)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CFG_NAND_CS 1
+#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
+#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
/*-----------------------------------------------------------------------
* DDR SDRAM
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* Flash configuration, expect one 16 Megabyte Bank at most
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
/*
* NAND Flash
*/
-/* Use the new NAND code. (BOARDLIBS = drivers/nand/libnand.a required) */
#undef CFG_NAND_LEGACY
#define CFG_NAND0_BASE 0x0 /* 0x43100040 */ /* 0x10000000 */
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* Flash configuration
EBC_BXCR_BW_16BIT)
/* Memory Bank 1 (Xilinx System ACE controller) initialization */
-#define CFG_EBC_PB1AP 0x7F8FFE80
+#define CFG_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \
+ EBC_BXAP_TWT_ENCODE(4) | \
+ EBC_BXAP_BCE_DISABLE | \
+ EBC_BXAP_BCT_2TRANS | \
+ EBC_BXAP_CSN_ENCODE(0) | \
+ EBC_BXAP_OEN_ENCODE(0) | \
+ EBC_BXAP_WBN_ENCODE(0) | \
+ EBC_BXAP_WBF_ENCODE(0) | \
+ EBC_BXAP_TH_ENCODE(0) | \
+ EBC_BXAP_RE_DISABLED | \
+ EBC_BXAP_SOR_NONDELAYED | \
+ EBC_BXAP_BEM_WRITEONLY | \
+ EBC_BXAP_PEN_DISABLED)
#define CFG_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE) | \
EBC_BXCR_BS_1MB | \
EBC_BXCR_BU_RW | \
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
#include "../board/xilinx/ml401/xparameters.h"
#define CONFIG_MICROBLAZE 1 /* MicroBlaze CPU */
+#define MICROBLAZE_V5 1
#define CONFIG_ML401 1 /* ML401 Board */
/* uart */
#define CFG_BAUDRATE_TABLE { CONFIG_BAUDRATE }
/* setting reset address */
-#define CFG_RESET_ADDRESS TEXT_BASE
+/*#define CFG_RESET_ADDRESS TEXT_BASE*/
/* ethernet */
#define CONFIG_EMACLITE 1
-#define XPAR_EMAC_0_DEVICE_ID XPAR_XEMAC_NUM_INSTANCES
+#define XPAR_EMAC_0_DEVICE_ID XPAR_OPB_ETHERNET_0_DEVICE_ID
/* gpio */
#define CFG_GPIO_0 1
#define FREQUENCE XILINX_CLOCK_FREQ
#define CFG_TIMER_0_PRELOAD ( FREQUENCE/1000 )
+/* FSL */
+#define CFG_FSL_2
+#define FSL_INTR_2 1
+
/*
* memory layout - Example
* TEXT_BASE = 0x1200_0000;
/* global pointer */
#define CFG_GBL_DATA_SIZE 0x1000 /* size of global data */
-#define CFG_GBL_DATA_OFFSET (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE) /* start of global data */
+/* start of global data */
+#define CFG_GBL_DATA_OFFSET (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE)
/* monitor code */
#define SIZE 0x40000
#define CFG_FLASH_EMPTY_INFO 1 /* ?empty sector */
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+ #define CFG_FLASH_PROTECTION /* hardware flash protection */
#ifdef RAMENV
#define CFG_ENV_IS_NOWHERE 1
#define CFG_ENV_IS_NOWHERE 1
#define CFG_ENV_SIZE 0x1000
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SIZE)
+ #define CFG_FLASH_PROTECTION /* hardware flash protection */
#endif /* !FLASH */
#ifdef FLASH
CFG_CMD_IMI |\
CFG_CMD_NET |\
CFG_CMD_CACHE |\
+ CFG_CMD_FAT |\
+ CFG_CMD_EXT2 |\
+ CFG_CMD_JFFS2 |\
+ CFG_CMD_ECHO |\
CFG_CMD_IMLS |\
CFG_CMD_FLASH |\
+ CFG_CMD_MFSL |\
CFG_CMD_PING \
)
#else /* !RAMENV */
CFG_CMD_FLASH |\
CFG_CMD_PING |\
CFG_CMD_ENV |\
+ CFG_CMD_FAT |\
+ CFG_CMD_EXT2 |\
+ CFG_CMD_JFFS2 |\
+ CFG_CMD_ECHO |\
+ CFG_CMD_MFSL |\
CFG_CMD_SAVES \
)
CFG_CMD_BDI |\
CFG_CMD_RUN |\
CFG_CMD_LOADS |\
+ CFG_CMD_FAT |\
+ CFG_CMD_EXT2 |\
CFG_CMD_LOADB |\
CFG_CMD_IMI |\
CFG_CMD_NET |\
CFG_CMD_CACHE |\
+ CFG_CMD_MFSL |\
CFG_CMD_PING \
)
#endif /* !FLASH */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
+#if (CONFIG_COMMANDS & CFG_CMD_JFFS2)
+/* JFFS2 partitions */
+#define CONFIG_JFFS2_CMDLINE /* mtdparts command line support */
+#define MTDIDS_DEFAULT "nor0=ml401-0"
+
+/* default mtd partition table */
+#define MTDPARTS_DEFAULT "mtdparts=ml401-0:256k(u-boot),"\
+ "256k(env),3m(kernel),1m(romfs),"\
+ "1m(cramfs),-(jffs2)"
+#endif
+
/* Miscellaneous configurable options */
#define CFG_PROMPT "U-Boot-mONStR> "
#define CFG_CBSIZE 512 /* size of console buffer */
#define CFG_LONGHELP
#define CFG_LOAD_ADDR 0x12000000 /* default load address */
-#define CONFIG_BOOTDELAY 30
+#define CONFIG_BOOTDELAY 30
#define CONFIG_BOOTARGS "root=romfs"
#define CONFIG_HOSTNAME "ml401"
#define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm"
#define CFG_HZ 1000
/* system ace */
-/*#define CONFIG_SYSTEMACE
-#define DEBUG_SYSTEMACE
-#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR
-#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH
-#define CONFIG_DOS_PARTITION
-*/
+#define CONFIG_SYSTEMACE
+/* #define DEBUG_SYSTEMACE */
+#define SYSTEMACE_CONFIG_FPGA
+#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR
+#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_PREBOOT "echo U-BOOT for ML401;setenv preboot;echo"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" /* hardware flash protection */\
+ "nor0=ml401-0\0"\
+ "mtdparts=mtdparts=ml401-0:"\
+ "256k(u-boot),256k(env),3m(kernel),"\
+ "1m(romfs),1m(cramfs),-(jffs2)\0"
+
#endif /* __CONFIG_H */
#ifndef __CONFIG_H
#define __CONFIG_H
-
/*
* High Level Configuration Options
*/
-
/* CPU and board */
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* More exactly a MPC5200 */
CFG_CMD_MII | \
CFG_CMD_BEDBUG | \
CFG_CMD_NET | \
- CFG_CMD_PING)
+ CFG_CMD_PING | \
+ CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_I2C | \
+ CFG_CMD_DATE | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DTT)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_PHY_ADDR 0x2
#define CONFIG_PHY_TYPE 0x79c874
-
+#define CONFIG_RESET_PHY_R 1
/*
* Autobooting
* Default environment settings
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
- "sdram_test=0\0" \
"netdev=eth0\0" \
"hostname=motionpro\0" \
"netmask=255.255.0.0\0" \
"ipaddr=192.168.160.22\0" \
"serverip=192.168.1.1\0" \
"gatewayip=192.168.1.1\0" \
- "kernel_addr=200000\0" \
+ "console=ttyPSC0,115200\0" \
"u-boot_addr=100000\0" \
- "kernel_sector=20\0" \
- "kernel_size=1000\0" \
- "console=ttyS0,115200\0" \
+ "kernel_addr=200000\0" \
+ "fdt_addr=400000\0" \
+ "ramdisk_addr=500000\0" \
+ "multi_image_addr=800000\0" \
"rootpath=/opt/eldk-4.1/ppc_6xx\0" \
- "bootfile=/tftpboot/motionpro/uImage\0" \
"u-boot=/tftpboot/motionpro/u-boot.bin\0" \
- "load=tftp $(u-boot_addr) $(u-boot)\0" \
+ "bootfile=/tftpboot/motionpro/uImage\0" \
+ "fdt_file=/tftpboot/motionpro/motionpro.dtb\0" \
+ "ramdisk_file=/tftpboot/motionpro/uRamdisk\0" \
+ "multi_image_file=kernel+initrd+dtb.img\0" \
+ "load=tftp ${u-boot_addr} ${u-boot}\0" \
"update=prot off fff00000 fff3ffff; era fff00000 fff3ffff; " \
- "cp.b $(u-boot_addr) fff00000 $(filesize);" \
+ "cp.b ${u-boot_addr} fff00000 ${filesize};" \
"prot on fff00000 fff3ffff\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) console=$(console) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):" \
- "$(netmask):$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip;bootm $(kernel_addr) " \
- "$(ramdisk_addr)\0" \
- "net_nfs=tftp $(kernel_addr) $(bootfile); run nfsargs addip; " \
- "bootm $(kernel_addr)\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "fstype=ext3\0" \
- "fatargs=setenv bootargs init=/linuxrc rw\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "fat_args=setenv bootargs rw\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:" \
+ "${netmask}:${hostname}:${netdev}:off panic=1 " \
+ "console=${console}\0" \
+ "net_nfs=tftp ${kernel_addr} ${bootfile}; " \
+ "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip; " \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_self=tftp ${kernel_addr} ${bootfile}; " \
+ "tftp ${fdt_addr} ${fdt_file}; " \
+ "tftp ${ramdisk_addr} ${ramdisk_file}; " \
+ "run ramargs addip; " \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "fat_multi=run fat_args addip; fatload ide 0:1 " \
+ "${multi_image_addr} ${multi_image_file}; " \
+ "bootm ${multi_image_addr}\0" \
""
#define CONFIG_BOOTCOMMAND "run net_nfs"
-
/*
* do board-specific init
*/
/*
+ * Set IPB speed to 100MHz
+ */
+#define CFG_IPBCLK_EQUALS_XLBCLK
+
+
+/*
* Memory map
*/
/*
#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
#define CONFIG_FLASH_16BIT /* Flash is 16-bit */
+/*
+ * MTD configuration
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=motionpro-0"
+#define MTDPARTS_DEFAULT "mtdparts=motionpro-0:" \
+ "13m(fs),2m(kernel),256k(uboot)," \
+ "64k(env),64k(redund_env),64k(dtb)," \
+ "-(user_data)"
+
+/*
+ * IDE/ATA configuration
+ */
+#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+#define CFG_IDE_MAXBUS 1
+#define CFG_IDE_MAXDEVICE 1
+#define CONFIG_IDE_PREINIT
+
+#define CFG_ATA_DATA_OFFSET 0x0060
+#define CFG_ATA_REG_OFFSET CFG_ATA_DATA_OFFSET
+#define CFG_ATA_STRIDE 4
+#define CONFIG_DOS_PARTITION
+
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CFG_I2C_MODULE 2 /* select I2C module #2 */
+#define CFG_I2C_SPEED 100000 /* 100 kHz */
+#define CFG_I2C_SLAVE 0x7F
+
+
+/*
+ * EEPROM configuration
+ */
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE 1 /* DTT driver needs this */
+#define CFG_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
+#define CFG_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */
+
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_DS1337 1
+#define CFG_I2C_RTC_ADDR 0x68
+
+
+/*
+ * Status LED configuration
+ */
+#define CONFIG_STATUS_LED /* Status LED enabled */
+#define CONFIG_BOARD_SPECIFIC_LED
+
+#define ENABLE_GPIO_OUT 0x00000024
+#define LED_ON 0x00000010
+
+#ifndef __ASSEMBLY__
+/*
+ * In case of Motion-PRO, a LED is identified by its corresponding
+ * GPT Enable and Mode Select Register.
+ */
+typedef volatile unsigned long * led_id_t;
+
+extern void __led_init(led_id_t id, int state);
+extern void __led_toggle(led_id_t id);
+extern void __led_set(led_id_t id, int state);
+#endif /* __ASSEMBLY__ */
+
+
+/*
+ * Temperature sensor
+ */
+#define CONFIG_DTT_LM75 1
+#define CONFIG_DTT_SENSORS { 0x49 }
+
/*
* Environment settings
#define CFG_ENV_SIZE 0x1000
#define CFG_ENV_SECT_SIZE 0x10000
+/* Configuration of redundant environment */
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*
* Pin multiplexing configuration
/*
+ * Motion-PRO's CPLD revision control register
+ */
+#define CPLD_REV_REGISTER (CFG_CS2_START + 0x06)
+
+
+/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
/* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
#define CFG_RESET_ADDRESS 0xfff00100
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+
#endif /* __CONFIG_H */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
#endif
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
/*
* For 66 MHz PCI clock additional Wait State is needed for CS0 (flash).
*/
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
#define CONFIG_440GRX 1 /* Specific PPC440GRx */
#endif
#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external freq to pll */
+/* Detect Sequoia PLL input clock automatically via CPLD bit */
+#define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
+ 33333333 : 33000000)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
CFG_CMD_LOADS |\
CFG_CMD_LOADB |\
CFG_CMD_MISC |\
+ CFG_CMD_FAT |\
+ CFG_CMD_EXT2 |\
CFG_CMD_PING \
)
"base 0;" \
"echo"
-
/* system ace */
-/*#define CONFIG_SYSTEMACE
-#define DEBUG_SYSTEMACE
-#define CFG_SYSTEMACE_BASE 0xCF000000
-#define CFG_SYSTEMACE_WIDTH 16
-#define CONFIG_DOS_PARTITION*/
+#define CONFIG_SYSTEMACE
+/* #define DEBUG_SYSTEMACE */
+#define SYSTEMACE_CONFIG_FPGA
+#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR
+#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH
+#define CONFIG_DOS_PARTITION
#endif /* __CONFIG_H */
/*
* NAND Flash
*/
-/* Use the new NAND code. (BOARDLIBS = drivers/nand/libnand.a required) */
#define CONFIG_NEW_NAND_CODE
#define CFG_NAND0_BASE 0x0
#undef CFG_NAND1_BASE
#endif /* __PPC__ */
-#if defined (__ARM__) || defined (__I386__) || defined (__M68K__) || defined (__bfin__)
+#if defined (__ARM__) || defined (__I386__) || defined (__M68K__) || defined (__bfin__) ||\
+ defined (__microblaze__)
struct stat {
unsigned short st_dev;
#define SPR_8321E_REV11 0x80660011
#define SPR_8321_REV11 0x80670011
+#define SPR_8311_REV10 0x80B30010
+#define SPR_8311E_REV10 0x80B20010
+#define SPR_8313_REV10 0x80B10010
+#define SPR_8313E_REV10 0x80B00010
+
/* SPCR - System Priority Configuration Register
*/
#define SPCR_PCIHPE 0x10000000 /* PCI Highest Priority Enable */
#define SPCR_TSEC2BDP_SHIFT (31-29)
#define SPCR_TSEC2EP 0x00000003 /* TSEC2 emergency priority */
#define SPCR_TSEC2EP_SHIFT (31-31)
+
+#elif defined(CONFIG_MPC831X)
+/* SPCR bits - MPC831x specific */
+#define SPCR_TSECDP 0x00003000 /* TSEC data priority */
+#define SPCR_TSECDP_SHIFT (31-19)
+#define SPCR_TSECEP 0x00000C00 /* TSEC emergency priority */
+#define SPCR_TSECEP_SHIFT (31-21)
+#define SPCR_TSECBDP 0x00000300 /* TSEC buffer descriptor priority */
+#define SPCR_TSECBDP_SHIFT (31-23)
#endif
/* SICRL/H - System I/O Configuration Register Low/High
#define SICRL_PCI_MSRC 0x10000000
#define SICRL_URT_CTPR 0x06000000
#define SICRL_IRQ_CTPR 0x00C00000
+
+#elif defined(CONFIG_MPC831X)
+/* SICRL bits - MPC831x specific */
+#define SICRL_LBC 0x30000000
+#define SICRL_UART 0x0C000000
+#define SICRL_SPI_A 0x03000000
+#define SICRL_SPI_B 0x00C00000
+#define SICRL_SPI_C 0x00300000
+#define SICRL_SPI_D 0x000C0000
+#define SICRL_USBDR 0x00000C00
+#define SICRL_ETSEC1_A 0x0000000C
+#define SICRL_ETSEC2_A 0x00000003
+
+/* SICRH bits - MPC831x specific */
+#define SICRH_INTR_A 0x02000000
+#define SICRH_INTR_B 0x00C00000
+#define SICRH_IIC 0x00300000
+#define SICRH_ETSEC2_B 0x000C0000
+#define SICRH_ETSEC2_C 0x00030000
+#define SICRH_ETSEC2_D 0x0000C000
+#define SICRH_ETSEC2_E 0x00003000
+#define SICRH_ETSEC2_F 0x00000C00
+#define SICRH_ETSEC2_G 0x00000300
+#define SICRH_ETSEC1_B 0x00000080
+#define SICRH_ETSEC1_C 0x00000060
+#define SICRH_GTX1_DLY 0x00000008
+#define SICRH_GTX2_DLY 0x00000004
+#define SICRH_TSOBI1 0x00000002
+#define SICRH_TSOBI2 0x00000001
+
#endif
/* SWCRR - System Watchdog Control Register
#define HRCWH_ROM_LOC_LOCAL_16BIT 0x00600000
#define HRCWH_ROM_LOC_LOCAL_32BIT 0x00700000
+#if defined(CONFIG_MPC831X)
+#define HRCWH_ROM_LOC_NAND_SP_8BIT 0x00100000
+#define HRCWH_ROM_LOC_NAND_SP_16BIT 0x00200000
+#define HRCWH_ROM_LOC_NAND_LP_8BIT 0x00500000
+#define HRCWH_ROM_LOC_NAND_LP_16BIT 0x00600000
+
+#define HRCWH_RL_EXT_LEGACY 0x00000000
+#define HRCWH_RL_EXT_NAND 0x00040000
+
+#define HRCWH_TSEC1M_IN_MII 0x00000000
+#define HRCWH_TSEC1M_IN_RMII 0x00002000
+#define HRCWH_TSEC1M_IN_RGMII 0x00006000
+#define HRCWH_TSEC1M_IN_RTBI 0x0000A000
+#define HRCWH_TSEC1M_IN_SGMII 0x0000C000
+
+#define HRCWH_TSEC2M_IN_MII 0x00000000
+#define HRCWH_TSEC2M_IN_RMII 0x00000400
+#define HRCWH_TSEC2M_IN_RGMII 0x00000C00
+#define HRCWH_TSEC2M_IN_RTBI 0x00001400
+#define HRCWH_TSEC2M_IN_SGMII 0x00001800
+#endif
+
#if defined(CONFIG_MPC834X)
#define HRCWH_TSEC1M_IN_RGMII 0x00000000
#define HRCWH_TSEC1M_IN_RTBI 0x00004000
#define SCCR_TSEC2CM_1 0x10000000
#define SCCR_TSEC2CM_2 0x20000000
#define SCCR_TSEC2CM_3 0x30000000
+
+#elif defined(CONFIG_MPC831X)
+/* TSEC1 bits are for TSEC2 as well */
+#define SCCR_TSEC1CM 0xc0000000
+#define SCCR_TSEC1CM_SHIFT 30
+#define SCCR_TSEC1CM_1 0x40000000
+#define SCCR_TSEC1CM_2 0x80000000
+#define SCCR_TSEC1CM_3 0xC0000000
+
+#define SCCR_TSEC1ON 0x20000000
+#define SCCR_TSEC2ON 0x10000000
+
#endif
#define SCCR_USBMPHCM 0x00c00000
#define CSCONFIG_COL_BIT_10 0x00000002
#define CSCONFIG_COL_BIT_11 0x00000003
+/* TIMING_CFG_0 - DDR SDRAM Timing Configuration 0
+ */
+#define TIMING_CFG0_RWT 0xC0000000
+#define TIMING_CFG0_RWT_SHIFT 30
+#define TIMING_CFG0_WRT 0x30000000
+#define TIMING_CFG0_WRT_SHIFT 28
+#define TIMING_CFG0_RRT 0x0C000000
+#define TIMING_CFG0_RRT_SHIFT 26
+#define TIMING_CFG0_WWT 0x03000000
+#define TIMING_CFG0_WWT_SHIFT 24
+#define TIMING_CFG0_ACT_PD_EXIT 0x00700000
+#define TIMING_CFG0_ACT_PD_EXIT_SHIFT 20
+#define TIMING_CFG0_PRE_PD_EXIT 0x00070000
+#define TIMING_CFG0_PRE_PD_EXIT_SHIFT 16
+#define TIMING_CFG0_ODT_PD_EXIT 0x00000F00
+#define TIMING_CFG0_ODT_PD_EXIT_SHIFT 8
+#define TIMING_CFG0_MRS_CYC 0x00000F00
+#define TIMING_CFG0_MRS_CYC_SHIFT 0
+
/* TIMING_CFG_1 - DDR SDRAM Timing Configuration 1
*/
#define TIMING_CFG1_PRETOACT 0x70000000
#define TIMING_CFG2_WR_DATA_DELAY_SHIFT 10
#define TIMING_CFG2_CPO_DEF 0x00000000 /* default (= CASLAT + 1) */
+#define TIMING_CFG2_ADD_LAT 0x70000000
+#define TIMING_CFG2_ADD_LAT_SHIFT 28
+#define TIMING_CFG2_WR_LAT_DELAY 0x00380000
+#define TIMING_CFG2_WR_LAT_DELAY_SHIFT 19
+#define TIMING_CFG2_RD_TO_PRE 0x0000E000
+#define TIMING_CFG2_RD_TO_PRE_SHIFT 13
+#define TIMING_CFG2_CKE_PLS 0x000001C0
+#define TIMING_CFG2_CKE_PLS_SHIFT 6
+#define TIMING_CFG2_FOUR_ACT 0x0000003F
+#define TIMING_CFG2_FOUR_ACT_SHIFT 0
+
/* DDR_SDRAM_CFG - DDR SDRAM Control Configuration
*/
#define SDRAM_CFG_MEM_EN 0x80000000
#define SDRAM_CFG_ECC_EN 0x20000000
#define SDRAM_CFG_RD_EN 0x10000000
#define SDRAM_CFG_SDRAM_TYPE 0x03000000
+#define SDRAM_CFG_SDRAM_TYPE_DDR 0x02000000
#define SDRAM_CFG_SDRAM_TYPE_SHIFT 24
#define SDRAM_CFG_DYN_PWR 0x00200000
#define SDRAM_CFG_32_BE 0x00080000
#define SDRAM_CFG_8_BE 0x00040000
#define SDRAM_CFG_NCAP 0x00020000
#define SDRAM_CFG_2T_EN 0x00008000
-#define SDRAM_CFG_SDRAM_TYPE_DDR 0x02000000
+#define SDRAM_CFG_BI 0x00000001
/* DDR_SDRAM_MODE - DDR SDRAM Mode Register
*/
#define BR_PS_32 0x00001800 /* Port Size 32 bit */
#define BR_DECC 0x00000600
#define BR_DECC_SHIFT 9
+#define BR_DECC_OFF 0x00000000
+#define BR_DECC_CHK 0x00000200
+#define BR_DECC_CHK_GEN 0x00000400
#define BR_WP 0x00000100
#define BR_WP_SHIFT 8
#define BR_MSEL 0x000000E0
#define BR_MSEL_SHIFT 5
#define BR_MS_GPCM 0x00000000 /* GPCM */
+#define BR_MS_FCM 0x00000020 /* FCM */
#define BR_MS_SDRAM 0x00000060 /* SDRAM */
#define BR_MS_UPMA 0x00000080 /* UPMA */
#define BR_MS_UPMB 0x000000A0 /* UPMB */
#define OR_GPCM_EAD 0x00000001
#define OR_GPCM_EAD_SHIFT 0
+#define OR_FCM_AM 0xFFFF8000
+#define OR_FCM_AM_SHIFT 15
+#define OR_FCM_BCTLD 0x00001000
+#define OR_FCM_BCTLD_SHIFT 12
+#define OR_FCM_PGS 0x00000400
+#define OR_FCM_PGS_SHIFT 10
+#define OR_FCM_CSCT 0x00000200
+#define OR_FCM_CSCT_SHIFT 9
+#define OR_FCM_CST 0x00000100
+#define OR_FCM_CST_SHIFT 8
+#define OR_FCM_CHT 0x00000080
+#define OR_FCM_CHT_SHIFT 7
+#define OR_FCM_SCY 0x00000070
+#define OR_FCM_SCY_SHIFT 4
+#define OR_FCM_SCY_1 0x00000010
+#define OR_FCM_SCY_2 0x00000020
+#define OR_FCM_SCY_3 0x00000030
+#define OR_FCM_SCY_4 0x00000040
+#define OR_FCM_SCY_5 0x00000050
+#define OR_FCM_SCY_6 0x00000060
+#define OR_FCM_SCY_7 0x00000070
+#define OR_FCM_RST 0x00000008
+#define OR_FCM_RST_SHIFT 3
+#define OR_FCM_TRLX 0x00000004
+#define OR_FCM_TRLX_SHIFT 2
+#define OR_FCM_EHTR 0x00000002
+#define OR_FCM_EHTR_SHIFT 1
+
#define OR_UPM_AM 0xFFFF8000
#define OR_UPM_AM_SHIFT 15
#define OR_UPM_XAM 0x00006000
#define PIWAR_IWS_1G 0x0000001D
#define PIWAR_IWS_2G 0x0000001E
+/* PMCCR1 - PCI Configuration Register 1
+ */
+#define PMCCR1_POWER_OFF 0x00000020
+
+/* FMR - Flash Mode Register
+ */
+#define FMR_CWTO 0x0000F000
+#define FMR_CWTO_SHIFT 12
+#define FMR_BOOT 0x00000800
+#define FMR_ECCM 0x00000100
+#define FMR_AL 0x00000030
+#define FMR_AL_SHIFT 4
+#define FMR_OP 0x00000003
+#define FMR_OP_SHIFT 0
+
+/* FIR - Flash Instruction Register
+ */
+#define FIR_OP0 0xF0000000
+#define FIR_OP0_SHIFT 28
+#define FIR_OP1 0x0F000000
+#define FIR_OP1_SHIFT 24
+#define FIR_OP2 0x00F00000
+#define FIR_OP2_SHIFT 20
+#define FIR_OP3 0x000F0000
+#define FIR_OP3_SHIFT 16
+#define FIR_OP4 0x0000F000
+#define FIR_OP4_SHIFT 12
+#define FIR_OP5 0x00000F00
+#define FIR_OP5_SHIFT 8
+#define FIR_OP6 0x000000F0
+#define FIR_OP6_SHIFT 4
+#define FIR_OP7 0x0000000F
+#define FIR_OP7_SHIFT 0
+#define FIR_OP_NOP 0x0 /* No operation and end of sequence */
+#define FIR_OP_CA 0x1 /* Issue current column address */
+#define FIR_OP_PA 0x2 /* Issue current block+page address */
+#define FIR_OP_UA 0x3 /* Issue user defined address */
+#define FIR_OP_CM0 0x4 /* Issue command from FCR[CMD0] */
+#define FIR_OP_CM1 0x5 /* Issue command from FCR[CMD1] */
+#define FIR_OP_CM2 0x6 /* Issue command from FCR[CMD2] */
+#define FIR_OP_CM3 0x7 /* Issue command from FCR[CMD3] */
+#define FIR_OP_WB 0x8 /* Write FBCR bytes from FCM buffer */
+#define FIR_OP_WS 0x9 /* Write 1 or 2 bytes from MDR[AS] */
+#define FIR_OP_RB 0xA /* Read FBCR bytes to FCM buffer */
+#define FIR_OP_RS 0xB /* Read 1 or 2 bytes to MDR[AS] */
+#define FIR_OP_CW0 0xC /* Wait then issue FCR[CMD0] */
+#define FIR_OP_CW1 0xD /* Wait then issue FCR[CMD1] */
+#define FIR_OP_RBW 0xE /* Wait then read FBCR bytes */
+#define FIR_OP_RSW 0xF /* Wait then read 1 or 2 bytes */
+
+/* FCR - Flash Command Register
+ */
+#define FCR_CMD0 0xFF000000
+#define FCR_CMD0_SHIFT 24
+#define FCR_CMD1 0x00FF0000
+#define FCR_CMD1_SHIFT 16
+#define FCR_CMD2 0x0000FF00
+#define FCR_CMD2_SHIFT 8
+#define FCR_CMD3 0x000000FF
+#define FCR_CMD3_SHIFT 0
+
+/* FBAR - Flash Block Address Register
+ */
+#define FBAR_BLK 0x00FFFFFF
+
+/* FPAR - Flash Page Address Register
+ */
+#define FPAR_SP_PI 0x00007C00
+#define FPAR_SP_PI_SHIFT 10
+#define FPAR_SP_MS 0x00000200
+#define FPAR_SP_CI 0x000001FF
+#define FPAR_SP_CI_SHIFT 0
+#define FPAR_LP_PI 0x0003F000
+#define FPAR_LP_PI_SHIFT 12
+#define FPAR_LP_MS 0x00000800
+#define FPAR_LP_CI 0x000007FF
+#define FPAR_LP_CI_SHIFT 0
+
+/* LTESR - Transfer Error Status Register
+ */
+#define LTESR_BM 0x80000000
+#define LTESR_FCT 0x40000000
+#define LTESR_PAR 0x20000000
+#define LTESR_WP 0x04000000
+#define LTESR_ATMW 0x00800000
+#define LTESR_ATMR 0x00400000
+#define LTESR_CS 0x00080000
+#define LTESR_CC 0x00000001
+
+/* DDR Control Driver Register
+ */
+#define DDRCDR_EN 0x40000000
+#define DDRCDR_PZ 0x3C000000
+#define DDRCDR_PZ_MAXZ 0x00000000
+#define DDRCDR_PZ_HIZ 0x20000000
+#define DDRCDR_PZ_NOMZ 0x30000000
+#define DDRCDR_PZ_LOZ 0x38000000
+#define DDRCDR_PZ_MINZ 0x3C000000
+#define DDRCDR_NZ 0x3C000000
+#define DDRCDR_NZ_MAXZ 0x00000000
+#define DDRCDR_NZ_HIZ 0x02000000
+#define DDRCDR_NZ_NOMZ 0x03000000
+#define DDRCDR_NZ_LOZ 0x03800000
+#define DDRCDR_NZ_MINZ 0x03C00000
+#define DDRCDR_ODT 0x00080000
+#define DDRCDR_DDR_CFG 0x00040000
+#define DDRCDR_M_ODR 0x00000002
+#define DDRCDR_Q_DRN 0x00000001
+
+#ifndef __ASSEMBLY__
+struct pci_region;
+void mpc83xx_pci_init(int num_buses, struct pci_region **reg, int warmboot);
+#endif
+
#endif /* __MPC83XX_H__ */
#define EXC_OFF_SYS_RESET 0x0100 /* System reset offset */
+
+/*
+ * platform register addresses
+ */
+
+#define GUTS_SVR (CFG_CCSRBAR + 0xE00A4)
+#define MCM_ABCR (CFG_CCSRBAR + 0x01000)
+#define MCM_DBCR (CFG_CCSRBAR + 0x01008)
+
/*
* l2cr values. Look in config_<BOARD>.h for the actual setup
*/
#define sdrcfga (SDR_DCR_BASE+0x0) /* ADDR */
#define sdrcfgd (SDR_DCR_BASE+0x1) /* Data */
-#define mtsdr(reg, data) mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data)
-#define mfsdr(reg, data) mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd)
+#define mtsdr(reg, data) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data); } while (0)
+#define mfsdr(reg, data) do { mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd); } while (0)
#define sdrnand0 0x4000
#define sdrultra0 0x4040
/*
* Macro for accessing the indirect CPR register
*/
-#define mtcpr(reg, data) mtdcr(cprcfga,reg);mtdcr(cprcfgd,data)
-#define mfcpr(reg, data) mtdcr(cprcfga,reg);data = mfdcr(cprcfgd)
+#define mtcpr(reg, data) do { mtdcr(cprcfga,reg);mtdcr(cprcfgd,data); } while (0)
+#define mfcpr(reg, data) do { mtdcr(cprcfga,reg);data = mfdcr(cprcfgd); } while (0)
#define CPR_CLKUPD_ENPLLCH_EN 0x40000000 /* Enable CPR PLL Changes */
#define CPR_CLKUPD_ENDVCH_EN 0x20000000 /* Enable CPR Sys. Div. Changes */
/*----------------------------------------------------------------------------+
| Clock / Power-on-reset DCR's.
+----------------------------------------------------------------------------*/
-#define CPR0_CFGADDR 0x00C
-#define CPR0_CFGDATA 0x00D
-
#define CPR0_CLKUPD 0x20
#define CPR0_CLKUPD_BSY_MASK 0x80000000
#define CPR0_CLKUPD_BSY_COMPLETED 0x00000000
#define mtsdr(reg, data) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data); } while (0)
#define mfsdr(reg, data) do { mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd); } while (0)
+/*
+ * All 44x except 440GP have CPR registers (indirect DCR)
+ */
+#if !defined(CONFIG_440GP)
+#define CPR0_CFGADDR 0x00C
+#define CPR0_CFGDATA 0x00D
+
+#define mtcpr(reg, data) do { \
+ mtdcr(CPR0_CFGADDR, reg); \
+ mtdcr(CPR0_CFGDATA, data); \
+ } while (0)
+
+#define mfcpr(reg, data) do { \
+ mtdcr(CPR0_CFGADDR, reg); \
+ data = mfdcr(CPR0_CFGDATA); \
+ } while (0)
+#endif
#ifndef __ASSEMBLY__
# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+#elif defined(CONFIG_MOTIONPRO)
+
+#define STATUS_LED_BIT ((vu_long *) MPC5XXX_GPT6_ENABLE)
+#define STATUS_LED_PERIOD (CFG_HZ / 10)
+#define STATUS_LED_STATE STATUS_LED_BLINKING
+
+#define STATUS_LED_BIT1 ((vu_long *) MPC5XXX_GPT7_ENABLE)
+#define STATUS_LED_PERIOD1 (CFG_HZ / 10)
+#define STATUS_LED_STATE1 STATUS_LED_OFF
+
+#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
#else
# error Status LED configuration missing
#endif
prt_8260_clks,
#endif /* CONFIG_8260 */
-#if defined(CONFIG_MPC83XX)
- print_clock_conf,
-#endif
-
checkcpu,
#if defined(CONFIG_MPC5xxx)
prt_mpc5xxx_clks,
bd->bi_procfreq = gd->cpu_clk; /* Processor Speed, In Hz */
bd->bi_plb_busfreq = gd->bus_clk;
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || \
+ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
bd->bi_pci_busfreq = get_PCI_freq ();
bd->bi_opbfreq = get_OPB_freq ();
#elif defined(CONFIG_XILINX_ML300)
CFLAGS += -DCONFIG_NAND_SPL
SOBJS = start.o init.o resetvec.o
-COBJS = nand_boot.o ndfc.o sdram.o speed.o
+COBJS = nand_boot.o ndfc.o sdram.o
SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
@rm -f $(obj)start.S
ln -s $(SRCTREE)/cpu/ppc4xx/start.S $(obj)start.S
-$(obj)speed.c:
- @rm -f $(obj)speed.c
- ln -s $(SRCTREE)/cpu/ppc4xx/speed.c $(obj)speed.c
-
# from board directory
$(obj)init.S:
@rm -f $(obj)init.S
projects / platform / kernel / u-boot.git / commitdiff