grep '#define[[:blank:]]CONFIG_' $CFG | \
sed -n 's/#define.\(CONFIG_[A-Za-z0-9_]*\).*/\1/p' | \
sort -u > ${KUSEDLST} || true
- NUM=`comm -12 --total --output-delimiter=, ${KSYMLST} ${KUSEDLST} | \
+ NUM=`comm -123 --total --output-delimiter=, ${KSYMLST} ${KUSEDLST} | \
cut -d , -f 3`
if [[ $NUM -ne 0 ]]; then
echo "Unmigrated symbols found in $CFG"
grep '#define[[:blank:]]CONFIG_' $CFG |
sed -n 's/#define.\(CONFIG_[A-Za-z0-9_]*\).*/\1/p' |
sort -u > ${KUSEDLST} || true;
- NUM=`comm -12 --total --output-delimiter=, ${KSYMLST} ${KUSEDLST} |
+ NUM=`comm -123 --total --output-delimiter=, ${KSYMLST} ${KUSEDLST} |
cut -d , -f 3`;
if [[ $NUM -ne 0 ]]; then
echo "Unmigrated symbols found in $CFG";
See Freescale App Note 4493 for more information about
this erratum.
- CONFIG_A003399_NOR_WORKAROUND
- Enables a workaround for IFC erratum A003399. It is only
- required during NOR boot.
-
- CONFIG_A008044_WORKAROUND
- Enables a workaround for T1040/T1042 erratum A008044. It is only
- required during NAND boot and valid for Rev 1.0 SoC revision
-
CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
This is the value to write into CCSR offset 0x18600
boards with QUICC Engines require OF_QE to set UCC MAC
addresses
- CONFIG_OF_SYSTEM_SETUP
-
- Other code has addition modification that it wants to make
- to the flat device tree before handing it off to the kernel.
- This causes ft_system_setup() to be called before booting
- the kernel.
-
CONFIG_OF_IDE_FIXUP
U-Boot can detect if an IDE device is present or not.
FLAGADM
- Error Recovery:
- CONFIG_NET_RETRY_COUNT
-
- This variable defines the number of retries for
- network operations like ARP, RARP, TFTP, or BOOTP
- before giving up the operation. If not defined, a
- default value of 5 is used.
-
- CONFIG_ARP_TIMEOUT
-
- Timeout waiting for an ARP reply in milliseconds.
-
- CONFIG_NFS_TIMEOUT
-
- Timeout in milliseconds used in NFS protocol.
- If you encounter "ERROR: Cannot umount" in nfs command,
- try longer timeout such as
- #define CONFIG_NFS_TIMEOUT 10000UL
-
Note:
In the current implementation, the local variables
CONFIG_SPL_SKIP_RELOCATE
Avoid SPL relocation
- CONFIG_SPL_NAND_IDENT
- SPL uses the chip ID list to identify the NAND flash.
- Requires CONFIG_SPL_NAND_BASE.
-
CONFIG_SPL_UBI
Support for a lightweight UBI (fastmap) scanner and
loader
This can be overridden at run-time by setting the bootm_boot_mode env.
variable to "sec" or "nonsec".
+config HAS_ARMV7_SECURE_BASE
+ bool "Enable support for a ahardware secure memory area"
+ default y if ARCH_LS1021A || ARCH_MX7 || ARCH_MX7ULP || ARCH_STM32MP \
+ || MACH_SUN6I || MACH_SUN7I || MACH_SUN8I || TEGRA124
+
+config ARMV7_SECURE_BASE
+ hex "Base address for secure mode memory"
+ depends on HAS_ARMV7_SECURE_BASE
+ default 0xfff00000 if TEGRA124
+ default 0x2ffc0000 if ARCH_STM32MP
+ default 0x2f000000 if ARCH_MX7ULP
+ default 0x10010000 if ARCH_LS1021A
+ default 0x00900000 if ARCH_MX7
+ default 0x00044000 if MACH_SUN8I
+ default 0x00020000 if MACH_SUN6I || MACH_SUN7I
+
+config ARMV7_SECURE_RESERVE_SIZE
+ hex
+ depends on TEGRA124 && HAS_ARMV7_SECURE_BASE
+ default 0x100000
+ help
+ Reserve top 1M for secure RAM
+
+config ARMV7_SECURE_MAX_SIZE
+ hex
+ depends on ARMV7_SECURE_BASE && ARCH_STM32MP || MACH_SUN6I \
+ || MACH_SUN7I || MACH_SUN8I
+ default 0xbc00 if MACH_SUN8I && !MACH_SUN8I_H3
+ default 0x3c00 if MACH_SUN8I && MACH_SUN8I_H3
+ default 0x10000
+
config ARMV7_VIRT
bool "Enable support for hardware virtualization" if EXPERT
depends on CPU_V7_HAS_VIRT && ARMV7_NONSEC
it can be safely enabled when EL2/EL3 initialized SMPEN bit
or when CPU implementation doesn't include that register.
+config ARMV8_SWITCH_TO_EL1
+ bool "Enable switching to running in EL1"
+ help
+ In some circumstances we need to switch to running in EL1.
+ Enable this option to have U-Boot switch to EL1.
+
config ARMV8_SPIN_TABLE
bool "Support spin-table enable method"
depends on ARMV8_MULTIENTRY && OF_LIBFDT
config TARGET_SAMA5D27_SOM1_EK
bool "SAMA5D27 SOM1 EK board"
+ select SAMA5D2
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select CPU_V7A
Enable the driver for the embedded flash used in the Atmel
AT91SAM9XE devices.
+config AT91_GPIO_PULLUP
+ bool "Keep pullups on peripheral pins"
+ depends on CPU_ARM926EJS
+
+config ATMEL_LEGACY
+ bool "Legacy GPIO support"
+
source "board/atmel/at91sam9260ek/Kconfig"
source "board/atmel/at91sam9261ek/Kconfig"
source "board/atmel/at91sam9263ek/Kconfig"
#define CONFIG_DM_SEQ_ALIAS 1
/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_ARP_TIMEOUT 200
-#define CONFIG_NET_RETRY_COUNT 50
-#endif /* CONFIG_CMD_NET */
-
-/*
* I2C related stuff
*/
#ifdef CONFIG_CMD_I2C
image, this area is no longer used, and can be reclaimed
for run time use by the boot image.
endif
+
+config AM335X_USB0
+ bool "Static mode configuration for USB0 in SPL"
+ depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL
+
+choice
+ prompt "USB0 port configuration"
+ depends on AM335X_USB0
+
+config AM335X_USB0_HOST
+ bool "Port is used in host mode"
+
+config AM335X_USB0_PERIPHERAL
+ bool "Port is used in peripheral mode"
+
+endchoice
+
+config AM335X_USB1
+ bool "Static mode configuration for USB1 in SPL"
+ depends on AM33XX && SPL_MUSB_NEW && !SPL_OF_CONTROL
+
+choice
+ prompt "USB1 port configuration"
+ depends on AM335X_USB1
+
+config AM335X_USB1_HOST
+ bool "Port is used in host mode"
+
+config AM335X_USB1_PERIPHERAL
+ bool "Port is used in peripheral mode"
+
+endchoice
};
U_BOOT_DRVINFOS(am33xx_usbs) = {
-#if CONFIG_AM335X_USB0_MODE == MUSB_PERIPHERAL
+#ifdef CONFIG_AM335X_USB0_PERIPHERAL
{ "ti-musb-peripheral", &usb0 },
-#elif CONFIG_AM335X_USB0_MODE == MUSB_HOST
+#elif defined(CONFIG_AM335X_USB0_HOST)
{ "ti-musb-host", &usb0 },
#endif
-#if CONFIG_AM335X_USB1_MODE == MUSB_PERIPHERAL
+#ifdef CONFIG_AM335X_USB1_PERIPHERAL
{ "ti-musb-peripheral", &usb1 },
-#elif CONFIG_AM335X_USB1_MODE == MUSB_HOST
+#elif defined(CONFIG_AM335X_USB1_HOST)
{ "ti-musb-host", &usb1 },
#endif
};
REVID_MAJOR(spridr) >= 2)
fdt_fixup_crypto_node(blob, 0x0204);
-#if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) ||\
- defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) ||\
- defined(CONFIG_HAS_ETH4) || defined(CONFIG_HAS_ETH5)
#ifdef CONFIG_ARCH_MPC8313
/*
* mpc8313e erratum IPIC1 swapped TSEC interrupt ID numbers on rev. 1
nodeoffset = fdt_path_offset(blob, "/aliases");
if (nodeoffset >= 0) {
-#if defined(CONFIG_HAS_ETH0)
prop = fdt_getprop(blob, nodeoffset, "ethernet0", NULL);
if (prop) {
u32 tmp[] = { 32, 0x8, 33, 0x8, 34, 0x8 };
fdt_setprop(blob, path, "interrupts",
&tmp, sizeof(tmp));
}
-#endif
-#if defined(CONFIG_HAS_ETH1)
prop = fdt_getprop(blob, nodeoffset, "ethernet1", NULL);
if (prop) {
u32 tmp[] = { 35, 0x8, 36, 0x8, 37, 0x8 };
fdt_setprop(blob, path, "interrupts",
&tmp, sizeof(tmp));
}
-#endif
}
}
#endif
-#endif
do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
"timebase-frequency", (bd->bi_busfreq / 4), 1);
config ARCH_P1010
bool
+ select A003399_NOR_WORKAROUND if SYS_FSL_ERRATUM_IFC_A003399 && !SPL
select BTB
select FSL_LAW
select SYS_CACHE_SHIFT_5
if changed by pre-boot regime. The value here must match
the current value in SoC. If not sure, do not change.
+config A003399_NOR_WORKAROUND
+ bool
+ help
+ Enables a workaround for IFC erratum A003399. It is only required
+ during NOR boot.
+
+config A008044_WORKAROUND
+ bool
+ help
+ Enables a workaround for T1040/T1042 erratum A008044. It is only
+ required during NAND boot and valid for Rev 1.0 SoC revision
+
config SYS_FSL_ERRATUM_A004468
bool
config SYS_FSL_ERRATUM_A008044
bool
+ select A008044_WORKAROUND if MTD_RAW_NAND
config SYS_FSL_ERRATUM_CPC_A002
bool
flush_cache(bootpg, 4096);
/* look for the tlb covering the reset page, there better be one */
- i = find_tlb_idx((void *)CONFIG_BPTR_VIRT_ADDR, 1);
+ i = find_tlb_idx((void *)BPTR_VIRT_ADDR, 1);
/* we found a match */
if (i != -1) {
/* map reset page to bootpg so we can copy code there */
disable_tlb(i);
- set_tlb(1, CONFIG_BPTR_VIRT_ADDR, bootpg, /* tlb, epn, rpn */
+ set_tlb(1, BPTR_VIRT_ADDR, bootpg, /* tlb, epn, rpn */
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */
0, i, BOOKE_PAGESZ_4K, 1); /* ts, esel, tsize, iprot */
- memcpy((void *)CONFIG_BPTR_VIRT_ADDR, (void *)fixup, 4096);
+ memcpy((void *)BPTR_VIRT_ADDR, (void *)fixup, 4096);
plat_mp_up(bootpg_map, pagesize);
} else {
* Freescale's default e500 reset page.
*/
#if (defined(CONFIG_E500) && defined(CONFIG_MP))
-#ifndef CONFIG_BPTR_VIRT_ADDR
-#define CONFIG_BPTR_VIRT_ADDR 0xfffff000
-#endif
+#define BPTR_VIRT_ADDR 0xfffff000
#endif
/* Since so many PPC SOCs have a semi-common LBC, define this here */
config SYS_CONFIG_NAME
default "at91sam9260ek"
+choice
+ prompt "Evaluation board"
+
+config AT91SAM9G20EK
+ bool "Atmel AT91SAM9G20 EK"
+
+config AT91SAM9260EK
+ bool "Atmel AT91SAM9260 EK"
+
+endchoice
+
+config AT91SAM9G20EK_2MMC
+ bool "Atmel AT91SAM9G20 EK 2MMC variant"
+ depends on AT91SAM9260EK
+
endif
config SYS_CONFIG_NAME
default "at91sam9261ek"
+choice
+ prompt "Evaluation board"
+
+config AT91SAM9G10EK
+ bool "Atmel AT91SAM9G10 EK"
+
+config AT91SAM9261EK
+ bool "Atmel AT91SAM9261 EK"
+
+config AT91SAM9G10
+ bool "Atmel AT91SAM9G10 EK"
+
+endchoice
+
endif
at91_periph_clk_enable(ATMEL_ID_LCDC);
- gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE;
+ /* board specific(not enough SRAM) */
+ gd->fb_base = 0x73E00000;
}
#ifdef CONFIG_LCD_INFO
int board_init(void)
{
/* arch number of AT91SAM9M10G45EK-Board */
-#ifdef CONFIG_AT91SAM9M10G45EK
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK;
-#elif defined CONFIG_AT91SAM9G45EKES
- gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G45EKES;
-#endif
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
goto free_phydev;
#endif
-#ifdef CONFIG_CI_UDC
- /* For otg ethernet*/
- usb_eth_initialize(bis);
-#endif
return 0;
free_phydev:
environmnent variable (if enabled) and before handling the boot delay.
See README.bootmenu for more details.
+config BOOT_RETRY
+ bool "Boot retry feature"
+ help
+ Allow for having the U-Boot command prompt time out and attempt
+ to boot again. If the environment variable "bootretry" is found then
+ its value is used, otherwise the retry timeout is
+ CONFIG_BOOT_RETRY_TIME. CONFIG_BOOT_RETRY_MIN is optional and
+ defaults to CONFIG_BOOT_RETRY_TIME. All times are in seconds.
+
+config BOOT_RETRY_TIME
+ int "Timeout in seconds before attempting to boot again"
+ depends on BOOT_RETRY
+ help
+ Time in seconds before the U-Boot prompt will timeout and boot will
+ be attempted again.
+
+config BOOT_RETRY_MIN
+ int "Minimum timeout in seconds for 'bootretry'"
+ depends on BOOT_RETRY
+ default BOOT_RETRY_TIME
+ help
+ The minimum time in seconds that "bootretry" can be set to.
+
+config RESET_TO_RETRY
+ bool "Reset the board to retry autoboot"
+ depends on BOOT_RETRY
+ help
+ After the countdown timed out, the board will be reset to restart
+ again.
+
endmenu
config USE_BOOTARGS
ifndef CONFIG_SPL_BUILD
-# This option is not just y/n - it can have a numeric value
-ifdef CONFIG_BOOT_RETRY_TIME
-obj-y += bootretry.o
-endif
-
+obj-$(CONFIG_BOOT_RETRY) += bootretry.o
obj-$(CONFIG_CMD_BOOTM) += bootm.o bootm_os.o
obj-$(CONFIG_CMD_BOOTZ) += bootm.o bootm_os.o
obj-$(CONFIG_CMD_BOOTI) += bootm.o bootm_os.o
#include <time.h>
#include <watchdog.h>
-#ifndef CONFIG_BOOT_RETRY_MIN
-#define CONFIG_BOOT_RETRY_MIN CONFIG_BOOT_RETRY_TIME
-#endif
-
static uint64_t endtime; /* must be set, default is instant timeout */
static int retry_time = -1; /* -1 so can call readline before main_loop */
help
Boot image via network using NFS protocol.
+config NFS_TIMEOUT
+ int "Timeout in milliseconds for NFS mounts"
+ depends on CMD_NFS
+ default 2000
+ help
+ Timeout in milliseconds used in NFS protocol. If you encounter
+ "ERROR: Cannot umount" in nfs command, try longer timeout such as
+ 10000.
+
config CMD_MII
bool "mii"
imply CMD_MDIO
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_USB1_VBUS_PIN="PH23"
CONFIG_USB2_VBUS_PIN="PH23"
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_AHCI=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_I2C=y
CONFIG_SPL=y
CONFIG_MACH_SUN8I_V3S=y
CONFIG_DRAM_CLK=360
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
# CONFIG_NETDEVICES is not set
CONFIG_ENV_ADDR=0xFE080000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="TSEC0"
CONFIG_DM=y
CONFIG_FSL_SATA=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_ENV_ADDR=0xFFF60000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="8548cds/uImage.uboot"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC0"
CONFIG_DM=y
CONFIG_CHIP_SELECTS_PER_CTRL=2
CONFIG_DDR_ECC=y
CONFIG_ENV_ADDR=0xFFF60000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="8548cds/uImage.uboot"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC0"
CONFIG_DM=y
CONFIG_CHIP_SELECTS_PER_CTRL=2
CONFIG_DDR_ECC=y
CONFIG_ENV_ADDR=0xFFF60000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="8548cds/uImage.uboot"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC0"
CONFIG_DM=y
CONFIG_CHIP_SELECTS_PER_CTRL=2
CONFIG_DDR_ECC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=2
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=2
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=2
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=2
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_CHIP_SELECTS_PER_CTRL=1
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_SYS_FSL_DDR3=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_SYS_FSL_DDR3=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_SYS_FSL_DDR3=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_SYS_FSL_DDR3=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_ENV_IS_IN_MMC=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC4"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_ENV_IS_IN_NAND=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xFFE20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC1"
CONFIG_DM=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
# CONFIG_SPL_BLK is not set
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_TI_COMMON_CMD_OPTIONS=y
CONFIG_DEFAULT_DEVICE_TREE="am335x-evm"
CONFIG_AM33XX=y
+CONFIG_AM335X_USB0=y
+CONFIG_AM335X_USB0_PERIPHERAL=y
+CONFIG_AM335X_USB1=y
CONFIG_SPL=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_TIMESTAMP=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_SPL_ENV_IS_NOWHERE=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_CLK=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_SPL_ENV_IS_NOWHERE=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_CLK=y
CONFIG_DEFAULT_DEVICE_TREE="am335x-guardian"
CONFIG_AM33XX=y
CONFIG_TARGET_AM335X_GUARDIAN=y
+CONFIG_AM335X_USB0=y
+CONFIG_AM335X_USB0_PERIPHERAL=y
+CONFIG_AM335X_USB1=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
CONFIG_BOOTCOUNT_BOOTLIMIT=3
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_SPL_ENV_IS_NOWHERE=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
CONFIG_REGMAP=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_CLK=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_CLK=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_AUTOBOOT_DELAY_STR="shc"
CONFIG_AUTOBOOT_STOP_STR="noautoboot"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=30
+CONFIG_RESET_TO_RETRY=y
CONFIG_BOOTCOMMAND="if mmc dev 1; mmc rescan; then run emmc_setup; else echo ERROR: eMMC device not detected!; panic; fi; if run loaduimage; then run mmcboot; else echo ERROR Unable to load uImage from eMMC!; echo Performing Rollback!; setenv _active_ ${active_root}; setenv _inactive_ ${inactive_root}; setenv active_root ${_inactive_}; setenv inactive_root ${_active_}; saveenv; reset; fi; "
CONFIG_DEFAULT_FDT_FILE="am335x-shc"
CONFIG_SYS_CONSOLE_INFO_QUIET=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_AUTOBOOT_DELAY_STR="shc"
CONFIG_AUTOBOOT_STOP_STR="noautoboot"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=30
+CONFIG_RESET_TO_RETRY=y
CONFIG_BOOTCOMMAND="run fusecmd; if run netboot; then echo Booting from network; else echo ERROR: Cannot boot from network!; panic; fi; "
CONFIG_DEFAULT_FDT_FILE="am335x-shc"
CONFIG_SYS_CONSOLE_INFO_QUIET=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
CONFIG_AUTOBOOT_DELAY_STR="shc"
CONFIG_AUTOBOOT_STOP_STR="noautoboot"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=30
+CONFIG_RESET_TO_RETRY=y
CONFIG_BOOTCOMMAND="if mmc dev 0; mmc rescan; then run sd_setup; else echo ERROR: SD/MMC-Card not detected!; panic; fi; if run loaduimage; then echo Bootable SD/MMC-Card inserted, booting from it!; run mmcboot; else echo ERROR: Unable to load uImage from SD/MMC-Card!; panic; fi; "
CONFIG_DEFAULT_FDT_FILE="am335x-shc"
CONFIG_SYS_CONSOLE_INFO_QUIET=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SYS_MMC_ENV_PART=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
CONFIG_DM_PCA953X=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_REGMAP=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_DFU_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_DFU_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_REGMAP=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_REGMAP=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_PART=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth0"
CONFIG_VERSION_VARIABLE=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_IP_DEFRAG=y
CONFIG_ENV_APPEND=y
CONFIG_ENV_WRITEABLE_LIST=y
CONFIG_ENV_ACCESS_IGNORE_FORCE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_VERSION_VARIABLE=y
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_APBH_DMA=y
CONFIG_APBH_DMA_BURST=y
CONFIG_ENV_APPEND=y
CONFIG_ENV_WRITEABLE_LIST=y
CONFIG_ENV_ACCESS_IGNORE_FORCE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_VERSION_VARIABLE=y
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_APBH_DMA=y
CONFIG_APBH_DMA_BURST=y
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9260,SYS_USE_DATAFLASH_CS0"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS0"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9260,SYS_USE_DATAFLASH_CS1"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS1"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9260ek"
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9260,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9261EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9261EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9261,SYS_USE_DATAFLASH_CS0"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS0"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9261EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9261EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9261,SYS_USE_DATAFLASH_CS3"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS3"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9261EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9261EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9261ek"
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9261,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_DATAFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_DATAFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x50000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_SECT_SIZE=0x10000
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_BOOT_NORFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_BOOT_NORFLASH"
CONFIG_BOOTDELAY=3
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_MALLOC_LEN=0x50000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9263EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_SECT_SIZE=0x10000
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_NORFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NORFLASH"
CONFIG_BOOTDELAY=3
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9261EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9G10=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G10,SYS_USE_DATAFLASH_CS0"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS0"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9261EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9G10=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G10,SYS_USE_DATAFLASH_CS3"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS3"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9261EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9G10=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9261ek"
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G10,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_SYS_MALLOC_LEN=0x23000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
+CONFIG_AT91SAM9G20EK_2MMC=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x1000
CONFIG_ENV_OFFSET=0x2000
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_MMC"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_MMC"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait"
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
+CONFIG_AT91SAM9G20EK_2MMC=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek_2mmc"
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,SYS_USE_DATAFLASH_CS0"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS0"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,SYS_USE_DATAFLASH_CS1"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS1"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek"
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x2c000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9M10G45EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4000
CONFIG_DM_GPIO=y
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9M10G45EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9m10g45ek"
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9RLEK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9RL,SYS_USE_DATAFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x2c000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9RLEK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4000
CONFIG_DM_GPIO=y
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9RL,SYS_USE_MMC"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_MMC"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 mtdparts=atmel_nand:8M(bootstrap/uboot/kernel)ro,-(rootfs) root=/dev/mmcblk0p2 rw rootwait"
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9RLEK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9rlek"
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9RL,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256K(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9X5EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9X5EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4000
CONFIG_DM_GPIO=y
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9X5EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g35ek"
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9X5EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x3000
CONFIG_ENV_OFFSET=0x5000
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9XE,SYS_USE_DATAFLASH_CS0"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS0"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x2d000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9XE,SYS_USE_DATAFLASH_CS1"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH_CS1"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_AT91SAM9260EK=y
+CONFIG_ATMEL_LEGACY=y
+CONFIG_AT91SAM9260EK=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9260ek"
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9XE,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_SYS_MALLOC_LEN=0x460000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_TAURUS=y
+CONFIG_AT91_GPIO_PULLUP=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SPL_SPI=y
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run flash_self"
CONFIG_DRAM_CLK=576
CONFIG_MMC0_CD_PIN="PH13"
CONFIG_USB1_VBUS_PIN="PH23"
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_AHCI=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_I2C=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=500
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_SYS_MMC_ENV_PART=2
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_NETCONSOLE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_NETCONSOLE=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_NETCONSOLE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_ARP_TIMEOUT=1500
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_NETCONSOLE=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_NETCONSOLE=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_SYS_MMC_ENV_PART=2
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_NETCONSOLE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_SYS_I2C_LEGACY=y
# CONFIG_ENV_IS_IN_MMC is not set
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_SPL_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_CMD_PCA953X=y
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_PHYLIB=y
CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_POWER_LEGACY=y
CONFIG_CMD_MVEBU_BUBT=y
# CONFIG_SPL_PARTITION_UUIDS is not set
CONFIG_ENV_OVERWRITE=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_AHCI_MVEBU=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_AHCI_MVEBU=y
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC0"
+CONFIG_ARP_TIMEOUT=200
CONFIG_SPL_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_DWC_AHSATA=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_CMD_PCA953X=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x80000
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_DM=y
CONFIG_PXA_MMC_GENERIC=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="ccdc.img"
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_SCSI_AHCI=y
CONFIG_DM_PCA953X=y
CONFIG_SYS_MALLOC_LEN=0x460000
CONFIG_SYS_MALLOC_F_LEN=0x800
CONFIG_TARGET_CORVUS=y
+CONFIG_AT91_GPIO_PULLUP=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SPL=y
CONFIG_ENV_OFFSET_REDUND=0x180000
CONFIG_SYS_LOAD_ADDR=0x70000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_DFU_NAND=y
CONFIG_CMD_UBI=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_BLK=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_ENV=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_BLK=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_ENV=y
CONFIG_CMD_UBI=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_BLK=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_ENV=y
CONFIG_CMD_UBI=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_BLK=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_ENV=y
CONFIG_CMD_UBI=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_BLK=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_ENV=y
CONFIG_CMD_UBI=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_BLK=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_ENV=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_DA8XX_GPIO=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SPL_OF_TRANSLATE=y
# CONFIG_SPL_BLK is not set
# CONFIG_BLOCK_CACHE is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_AHCI_MVEBU=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_SATA_MV=y
CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MVTWSI=y
# CONFIG_MMC is not set
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_MMC_ENV_PART=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_DWC_AHSATA=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=60
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_PREBOOT=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_SYS_LOAD_ADDR=0x20000
CONFIG_SYS_EXTRA_OPTIONS="SYS_MONITOR_BASE=0xFF000400"
CONFIG_BOOTDELAY=5
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=-1
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="printenv"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SYS_LOAD_ADDR=0x20000
CONFIG_SYS_EXTRA_OPTIONS="SYS_MONITOR_BASE=0xF0000418"
CONFIG_BOOTDELAY=5
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=-1
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="printenv"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=60
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_PREBOOT=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="ethernut5"
CONFIG_SYS_LOAD_ADDR=0x020000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9XE"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_SYS_MALLOC_LEN=0x1000000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_GARDENA_SMART_GATEWAY_AT91SAM=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_MMC_ENV_PART=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_SYS_TEXT_BASE=0x73f00000
CONFIG_SYS_MALLOC_LEN=0x100000
CONFIG_TARGET_GURNARD=y
+CONFIG_AT91_GPIO_PULLUP=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x40000
CONFIG_ENV_OFFSET=0x80000
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g45-gurnard"
CONFIG_SYS_LOAD_ADDR=0x23000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G45"
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_TFTP_TSIZE=y
CONFIG_AT91_GPIO=y
CONFIG_GENERIC_ATMEL_MCI=y
CONFIG_CMD_MVEBU_BUBT=y
# CONFIG_SPL_PARTITION_UUIDS is not set
CONFIG_ENV_OVERWRITE=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_AHCI_MVEBU=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds...\nPress <s> to stop or <d> to delay\n"
CONFIG_AUTOBOOT_KEYED_CTRLC=y
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=-1
+CONFIG_RESET_TO_RETRY=y
# CONFIG_USE_BOOTCOMMAND is not set
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Enter password - autoboot in %d seconds...\n"
CONFIG_AUTOBOOT_DELAY_STR="ids"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=900
+CONFIG_BOOT_RETRY_MIN=30
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run boot_cramfs"
CONFIG_USE_PREBOOT=y
CONFIG_ENV_ADDR_REDUND=0xFFFE0000
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="ids8313/uImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="TSEC1"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_I2C=y
CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
+CONFIG_ARP_TIMEOUT=200
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_DFU_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_SPL_CLK_COMPOSITE_CCF=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_SPL_CLK_COMPOSITE_CCF=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_SPL_CLK_COMPOSITE_CCF=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_SPL_DM=y
CONFIG_SPL_CLK_COMPOSITE_CCF=y
CONFIG_CLK_COMPOSITE_CCF=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth0"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_IP_DEFRAG=y
CONFIG_TFTP_BLOCKSIZE=4096
CONFIG_SYS_MMC_ENV_DEV=2
CONFIG_SYS_MMC_ENV_PART=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_REGMAP=y
CONFIG_SYS_MMC_ENV_DEV=2
CONFIG_SYS_MMC_ENV_PART=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_REGMAP=y
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_BOOTROM_SUPPORT=y
CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
CONFIG_SPL_I2C=y
CONFIG_SPL_POWER=y
CONFIG_SPL_WATCHDOG=y
CONFIG_SYS_MMC_ENV_DEV=2
CONFIG_SYS_MMC_ENV_PART=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_REGMAP=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth0"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_IP_DEFRAG=y
CONFIG_TFTP_BLOCKSIZE=4096
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_SPL_DM=y
CONFIG_CLK_COMPOSITE_CCF=y
CONFIG_CLK_IMX8MP=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
CONFIG_SPL=y
+CONFIG_IMX_BOOTAUX=y
CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
CONFIG_DEFAULT_DEVICE_TREE="imx8mp-rsb3720-a1"
CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
+CONFIG_SYS_LOAD_ADDR=0x40480000
CONFIG_FIT=y
CONFIG_FIT_EXTERNAL_OFFSET=0x3000
CONFIG_FIT_SIGNATURE=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_REGMAP=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
CONFIG_SPL=y
+CONFIG_IMX_BOOTAUX=y
CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
CONFIG_DEFAULT_DEVICE_TREE="imx8mp-rsb3720-a1"
CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
+CONFIG_SYS_LOAD_ADDR=0x40480000
CONFIG_FIT=y
CONFIG_FIT_EXTERNAL_OFFSET=0x3000
CONFIG_FIT_SIGNATURE=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_REGMAP=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
CONFIG_MXC_GPIO=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
CONFIG_MXC_GPIO=y
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
CONFIG_MXC_GPIO=y
CONFIG_DM_I2C=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_IMX_RGPIO2P=y
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
CONFIG_FLASH_CFI_MTD=y
CONFIG_SYS_FLASH_CFI=y
+CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_SFDP_SUPPORT=y
CONFIG_SPI_FLASH_SOFT_RESET=y
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
CONFIG_FLASH_CFI_MTD=y
CONFIG_SYS_FLASH_CFI=y
+CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_SFDP_SUPPORT=y
CONFIG_SPI_FLASH_SOFT_RESET=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=32
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=32
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=32
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=32
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_DFU_MMC=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=32
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=32
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=32
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=32
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xebf20000
CONFIG_ENV_ADDR_REDUND=0xebf00000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="fm1-mac5"
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_FSL_CAAM=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xF00C0000
CONFIG_ENV_ADDR_REDUND=0xF00E0000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="UEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xF00C0000
CONFIG_ENV_ADDR_REDUND=0xF00E0000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="UEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xF00C0000
CONFIG_ENV_ADDR_REDUND=0xF00E0000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="UEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xF00C0000
CONFIG_ENV_ADDR_REDUND=0xF00E0000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="UEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xF0100000
CONFIG_ENV_ADDR_REDUND=0xF0120000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="UEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xF00C0000
CONFIG_ENV_ADDR_REDUND=0xF00E0000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="UEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_BUS=2
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth0"
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_ENV=y
CONFIG_DM_I2C=y
CONFIG_SPL=y
CONFIG_IMX_BOOTAUX=y
CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
CONFIG_SYS_LOAD_ADDR=0x40480000
CONFIG_FIT=y
CONFIG_SPL_FIT_PRINT=y
CONFIG_SPL_LOAD_FIT=y
# CONFIG_USE_SPL_FIT_GENERATOR is not set
+CONFIG_OF_SYSTEM_SETUP=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_BOARD_LATE_INIT=y
CONFIG_MISC_INIT_R=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
CONFIG_SPL_I2C=y
CONFIG_SPL_POWER=y
CONFIG_SPL_WATCHDOG=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
CONFIG_DFU_MMC=y
CONFIG_MXC_GPIO=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_I2C_DEFAULT_BUS_NUMBER=0x1
CONFIG_SYS_I2C_MXC=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
# CONFIG_BLOCK_CACHE is not set
CONFIG_SPL_CLK_IMX6Q=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
+CONFIG_NFS_TIMEOUT=10000
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM_I2C=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC2"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC2"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x60300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x60300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x60300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x60300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eTSEC1"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d10000"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x60300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d10000"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x60300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d10000"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d10000"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d10000"
CONFIG_DM=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d10000"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d10000"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
# CONFIG_DDR_SPD is not set
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x60300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
# CONFIG_DDR_SPD is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_MPC8XXX_GPIO=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_MPC8XXX_GPIO=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
CONFIG_MPC8XXX_GPIO=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)"
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
# CONFIG_DDR_SPD is not set
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_ENV_ADDR=0x60500000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_FSL_CAAM=y
# CONFIG_DDR_SPD is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x40500000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x40300000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SPL_ENV_IS_NOWHERE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.spi-0:1m(rcw),15m(u-boot),48m(kernel.itb);7e800000.flash:16m(nand_uboot),48m(nand_kernel),448m(nand_free)"
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x40500000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FM1@DTSEC3"
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_CEVA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x80300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_CMD_CACHE=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20500000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_CMD_CACHE=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_CMD_CACHE=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20500000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
# CONFIG_ISO_PARTITION is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x80300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_CMD_DATE=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0x80300000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x580500000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20300000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_CMD_CACHE=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x580500000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_OF_LIST="fsl-lx2160a-qds-3-x-x fsl-lx2160a-qds-7-x-x fsl-lx2160a-qds-19-x-x fsl-lx2160a-qds-20-x-x fsl-lx2160a-qds-3-11-x fsl-lx2160a-qds-7-11-x fsl-lx2160a-qds-7-11-x fsl-lx2160a-qds-19-11-x fsl-lx2160a-qds-20-11-x"
CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC17@rgmii-id"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20500000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC17@rgmii-id"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_CMD_CACHE=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20500000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20500000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC1@xgmii"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_OF_LIST="fsl-lx2162a-qds-17-x fsl-lx2162a-qds-18-x fsl-lx2162a-qds-20-x"
CONFIG_MULTI_DTB_FIT=y
CONFIG_ENV_OVERWRITE=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC17@rgmii-id"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20500000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC17@rgmii-id"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_ADDR=0x20500000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="DPMAC17@rgmii-id"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="boot/fitImage"
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_LOAD_ADDR=0x20100000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_DATAFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_PREBOOT=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_LOAD_ADDR=0x20100000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_NANDFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_NANDFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_PREBOOT=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_AHCI_MVEBU=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_AHCI_MVEBU=y
CONFIG_CLK=y
CONFIG_CLK_MVEBU=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_AHCI_MVEBU=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_AHCI_MVEBU=y
CONFIG_DM_GPIO_LOOKUP_LABEL=y
CONFIG_DM_I2C=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_AHCI_PCI=y
CONFIG_AHCI_MVEBU=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_AHCI_MVEBU=y
CONFIG_DM_I2C=y
CONFIG_MAC_PARTITION=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_AHCI_MVEBU=y
CONFIG_DM_PCA953X=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC0"
+CONFIG_ARP_TIMEOUT=200
CONFIG_DM=y
CONFIG_FSL_ESDHC_IMX=y
CONFIG_MTD=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
CONFIG_FPGA_ALTERA=y
CONFIG_FPGA_CYCLON2=y
CONFIG_FSL_ESDHC_IMX=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC0"
+CONFIG_ARP_TIMEOUT=200
CONFIG_DM=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MXC=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_DFU_MMC=y
CONFIG_DFU_SF=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_USB_FUNCTION_FASTBOOT=y
CONFIG_FASTBOOT_BUF_ADDR=0x12000000
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM_PCA953X=y
CONFIG_DM_I2C=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=2
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MXC=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PCI=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_BOUNCE_BUFFER=y
CONFIG_USB_FUNCTION_FASTBOOT=y
CONFIG_DM_74X164=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM_74X164=y
CONFIG_DM_I2C=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth1"
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM_74X164=y
CONFIG_DM_I2C=y
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="imx7ulp-evk"
CONFIG_TARGET_MX7ULP_EVK=y
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_SYS_LOAD_ADDR=0x60800000
CONFIG_OF_BOARD_SETUP=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="imx7ulp-evk"
CONFIG_TARGET_MX7ULP_EVK=y
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_SYS_LOAD_ADDR=0x60800000
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; fi; fi; fi"
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_NETCONSOLE=y
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_SUPPORT_RAW_INITRD=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=-1
+CONFIG_BOOT_RETRY_MIN=30
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyAMA0,115200n8 earlycon=pl011,0x87e028000000 maxcpus=6 rootwait rw root=/dev/mmcblk0p2 coherent_pool=16M"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_SUPPORT_RAW_INITRD=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=-1
+CONFIG_BOOT_RETRY_MIN=30
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyAMA0,115200n8 earlycon=pl011,0x87e028000000 maxcpus=24 rootwait rw root=/dev/mmcblk0p2 coherent_pool=16M"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_SUPPORT_RAW_INITRD=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=-1
+CONFIG_BOOT_RETRY_MIN=30
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyAMA0,115200n8 earlycon=pl011,0x87e028000000 maxcpus=4 rootwait rw root=/dev/sda2 coherent_pool=16M"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_SUPPORT_RAW_INITRD=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=-1
+CONFIG_BOOT_RETRY_MIN=30
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyAMA0,115200n8 earlycon=pl011,0x87e028000000 maxcpus=24 rootwait rw root=/dev/sda2 coherent_pool=16M"
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="zImage"
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_DM=y
CONFIG_BOOTCOUNT_BOOTLIMIT=3
CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020
CONFIG_SYS_CLK_FREQ=66666666
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_LOAD_ADDR=0x82000000
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0x60060000
CONFIG_ENV_ADDR_REDUND=0x60040000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d90000"
CONFIG_VERSION_VARIABLE=y
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DEFAULT_DEVICE_TREE="ls1021a-pg-wcom-expu1"
CONFIG_BOOTCOUNT_BOOTLIMIT=3
CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_LOAD_ADDR=0x82000000
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0x60220000
CONFIG_ENV_ADDR_REDUND=0x60200000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d90000"
CONFIG_VERSION_VARIABLE=y
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_BOOTLIMIT=3
CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020
CONFIG_SYS_CLK_FREQ=66666666
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_LOAD_ADDR=0x82000000
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0x60060000
CONFIG_ENV_ADDR_REDUND=0x60040000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d90000"
CONFIG_VERSION_VARIABLE=y
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DEFAULT_DEVICE_TREE="ls1021a-pg-wcom-seli8"
CONFIG_BOOTCOUNT_BOOTLIMIT=3
CONFIG_SYS_BOOTCOUNT_ADDR=0x70000020
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_AHCI=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_LOAD_ADDR=0x82000000
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0x60220000
CONFIG_ENV_ADDR_REDUND=0x60200000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="ethernet@2d90000"
CONFIG_VERSION_VARIABLE=y
CONFIG_DM=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
# CONFIG_ISO_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=500
+CONFIG_NET_RETRY_COUNT=20
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_CLK=y
CONFIG_MMC=y
CONFIG_FSL_USDHC=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_BOUNCE_BUFFER=y
CONFIG_DFU_MMC=y
CONFIG_SYS_DFU_DATA_BUF_SIZE=0x1000000
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
CONFIG_MXC_GPIO=y
CONFIG_DM_I2C=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_DRAM_CLK=504
CONFIG_DRAM_ODT_EN=y
CONFIG_I2C0_ENABLE=y
+# CONFIG_HAS_ARMV7_SECURE_BASE is not set
CONFIG_SPL_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9261ek"
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9261"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="root=/dev/mtdblock4 rootfstype=jffs2 fbcon=rotate:3 "
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="root=/dev/mtdblock4 rootfstype=jffs2 fbcon=rotate:3 "
CONFIG_SYS_MALLOC_LEN=0x80000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_PM9G45=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9m10g45ek"
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=60
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_PREBOOT=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=60
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_PREBOOT=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=2
+CONFIG_ARP_TIMEOUT=200
CONFIG_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=60
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_PREBOOT=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
# CONFIG_DISPLAY_CPUINFO is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_TARGET_SAM9X60EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=8
CONFIG_ENV_SIZE=0x4000
CONFIG_DM_GPIO=y
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_TARGET_SAM9X60EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=8
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="sam9x60ek"
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_TARGET_SAM9X60EK=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=8
CONFIG_ENV_SECT_SIZE=0x1000
CONFIG_DM_GPIO=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_AUTOBOOT_KEYED=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_QSPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_QSPI_BOOT=y
CONFIG_SPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_SYS_BOOT_GET_KBD=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_QSPI_BOOT=y
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2"
CONFIG_NAND_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_MMC"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_MMC"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_MMC"
CONFIG_QSPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_ENV_IS_IN_FAT=y
CONFIG_ENV_FAT_DEVICE_AND_PART="1:1"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_CCF=y
CONFIG_ENV_IS_IN_FAT=y
CONFIG_ENV_FAT_DEVICE_AND_PART="0:1"
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_CCF=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth0"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_FSL_USDHC=y
CONFIG_MTD=y
CONFIG_SYS_MALLOC_LEN=0x460000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_SMARTWEB=y
+CONFIG_AT91_GPIO_PULLUP=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_ENV_OFFSET_REDUND=0x180000
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9260"
CONFIG_BOOTDELAY=3
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_DFU_NAND=y
CONFIG_SYS_TEXT_BASE=0x21f00000
CONFIG_SYS_MALLOC_LEN=0x100000
CONFIG_TARGET_SNAPPER9260=y
+CONFIG_AT91_GPIO_PULLUP=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x40000
CONFIG_ENV_OFFSET=0x80000
CONFIG_SYS_LOAD_ADDR=0x23000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9260"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 ip=any"
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_TFTP_TSIZE=y
CONFIG_AT91_GPIO=y
CONFIG_CMD_PCA953X=y
CONFIG_SYS_TEXT_BASE=0x21f00000
CONFIG_SYS_MALLOC_LEN=0x100000
CONFIG_TARGET_SNAPPER9260=y
+CONFIG_AT91_GPIO_PULLUP=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x40000
CONFIG_ENV_OFFSET=0x80000
CONFIG_SYS_LOAD_ADDR=0x23000000
CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 ip=any"
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_TFTP_TSIZE=y
CONFIG_AT91_GPIO=y
CONFIG_CMD_PCA953X=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="zImage"
CONFIG_VERSION_VARIABLE=y
+CONFIG_ARP_TIMEOUT=500
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DWAPB_GPIO=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_LOAD_ADDR=0x02000000
CONFIG_FIT=y
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=45
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 ubi.fm_autoconvert=1 uio_pdrv_genirq.of_id=\"idq,regbank\""
CONFIG_BOOTCOMMAND="setenv bootcmd 'bridge enable; if test ${bootnum} = 'b'; then run _fpga_loadsafe; else if test ${bootcount} -eq 4; then echo 'Switching copy...'; setexpr x $bootnum % 2 && setexpr bootnum $x + 1; saveenv; fi; run _fpga_loaduser; fi;echo 'Booting bank $bootnum' && run userload && run userboot;' && setenv altbootcmd 'setenv bootnum b && saveenv && boot;' && saveenv && saveenv && boot;"
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xFFF40000
CONFIG_ENV_ADDR_REDUND=0xFFF20000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="TSEC0"
CONFIG_DM=y
CONFIG_CHIP_SELECTS_PER_CTRL=2
CONFIG_SYS_BR0_PRELIM_BOOL=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth0"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_FSL_USDHC=y
CONFIG_SYS_MALLOC_LEN=0x460000
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_TAURUS=y
+CONFIG_AT91_GPIO_PULLUP=y
+CONFIG_ATMEL_LEGACY=y
CONFIG_BOARD_TAURUS=y
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_SPI=y
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_SPI_MAX_HZ=50000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_SATA_MV=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
+CONFIG_BOOT_RETRY=y
+CONFIG_BOOT_RETRY_TIME=60
+CONFIG_RESET_TO_RETRY=y
CONFIG_USE_PREBOOT=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_SPL_DM=y
# CONFIG_SPL_BLK is not set
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
+CONFIG_NET_RETRY_COUNT=10
CONFIG_BOOTP_SEND_HOSTNAME=y
CONFIG_DM=y
CONFIG_DM_I2C=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_SYS_I2C_MXC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_SYS_I2C_MXC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_SYS_I2C_MXC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_SYS_I2C_MXC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_SYS_I2C_MXC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
+CONFIG_ARP_TIMEOUT=200
CONFIG_BOUNCE_BUFFER=y
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
CONFIG_SYS_I2C_MXC=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xF00C0000
CONFIG_ENV_ADDR_REDUND=0xF00E0000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="UEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SCSI_AHCI=y
CONFIG_AHCI_PCI=y
CONFIG_BUTTON=y
# CONFIG_SPL_PARTITION_UUIDS is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_AHCI_PCI=y
CONFIG_AHCI_MVEBU=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR=0xF00C0000
CONFIG_ENV_ADDR_REDUND=0xF00E0000
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="UEC0"
CONFIG_VERSION_VARIABLE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_DM_BOOTCOUNT=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_AHCI_MVEBU=y
CONFIG_CLK=y
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="usb_a9263"
CONFIG_SYS_LOAD_ADDR=0x22000000
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9263,SYS_USE_DATAFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_USE_DATAFLASH"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock1 mtdparts=mtdparts=atmel_nand:16m(kernel)ro,120m(root1),-(root2) rw rootfstype=jffs2"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_ENV_SPI_MAX_HZ=15000000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth0"
CONFIG_DM_I2C_GPIO=y
CONFIG_SYS_I2C_MXC=y
CONFIG_MISC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_PART=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_VERSION_VARIABLE=y
CONFIG_IP_DEFRAG=y
CONFIG_TFTP_BLOCKSIZE=4096
CONFIG_IMX_BOOTAUX=y
CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
CONFIG_DISTRO_DEFAULTS=y
+CONFIG_REMAKE_ELF=y
CONFIG_SYS_LOAD_ADDR=0x43500000
CONFIG_FIT=y
CONFIG_FIT_EXTERNAL_OFFSET=0x3000
CONFIG_SYS_MMC_ENV_DEV=2
CONFIG_SYS_MMC_ENV_PART=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="eth0"
CONFIG_VERSION_VARIABLE=y
CONFIG_IP_DEFRAG=y
CONFIG_TFTP_BLOCKSIZE=4096
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_DM_SERIAL=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_DM_SERIAL=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RETRY_COUNT=20
CONFIG_AT91_GPIO=y
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_GENERIC_ATMEL_MCI=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_PART=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_USE_ETHPRIME=y
+CONFIG_ETHPRIME="FEC"
CONFIG_BOUNCE_BUFFER=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_CMD_UBI=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_ADDR=0x100000
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_MII
Must be defined if CONFIG_FEC_MXC is defined.
-CONFIG_FEC_XCV_TYPE
- Defaults to MII100 for 100 Base-tx.
- RGMII selects 1000 Base-tx reduced pin count interface.
- RMII selects 100 Base-tx reduced pin count interface.
-
CONFIG_FEC_MXC_SWAP_PACKET
Forced on iff MX28.
Swaps the bytes order of all words(4 byte units) in the packet.
#error "CONFIG_MII has to be defined!"
#endif
-#ifndef CONFIG_FEC_XCV_TYPE
-#define CONFIG_FEC_XCV_TYPE MII100
-#endif
-
/*
* The i.MX28 operates with packets in big endian. We need to swap them before
* sending and after receiving.
return !is_valid_ethaddr(mac);
}
-#ifdef CONFIG_DM_ETH
static int fecmxc_set_hwaddr(struct udevice *dev)
-#else
-static int fec_set_hwaddr(struct eth_device *dev)
-#endif
{
-#ifdef CONFIG_DM_ETH
struct fec_priv *fec = dev_get_priv(dev);
struct eth_pdata *pdata = dev_get_plat(dev);
uchar *mac = pdata->enetaddr;
-#else
- uchar *mac = dev->enetaddr;
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
-#endif
writel(0, &fec->eth->iaddr1);
writel(0, &fec->eth->iaddr2);
* Start the FEC engine
* @param[in] dev Our device to handle
*/
-#ifdef CONFIG_DM_ETH
static int fec_open(struct udevice *dev)
-#else
-static int fec_open(struct eth_device *edev)
-#endif
{
-#ifdef CONFIG_DM_ETH
struct fec_priv *fec = dev_get_priv(dev);
-#else
- struct fec_priv *fec = (struct fec_priv *)edev->priv;
-#endif
int speed;
ulong addr, size;
int i;
return 0;
}
-#ifdef CONFIG_DM_ETH
static int fecmxc_init(struct udevice *dev)
-#else
-static int fec_init(struct eth_device *dev, struct bd_info *bd)
-#endif
{
-#ifdef CONFIG_DM_ETH
struct fec_priv *fec = dev_get_priv(dev);
-#else
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
-#endif
u8 *mib_ptr = (uint8_t *)&fec->eth->rmon_t_drop;
u8 *i;
ulong addr;
/* Initialize MAC address */
-#ifdef CONFIG_DM_ETH
fecmxc_set_hwaddr(dev);
-#else
- fec_set_hwaddr(dev);
-#endif
/* Setup transmit descriptors, there are two in total. */
fec_tbd_init(fec);
* Halt the FEC engine
* @param[in] dev Our device to handle
*/
-#ifdef CONFIG_DM_ETH
static void fecmxc_halt(struct udevice *dev)
-#else
-static void fec_halt(struct eth_device *dev)
-#endif
{
-#ifdef CONFIG_DM_ETH
struct fec_priv *fec = dev_get_priv(dev);
-#else
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
-#endif
int counter = 0xffff;
/* issue graceful stop command to the FEC transmitter if necessary */
* @param[in] length Data count in bytes
* Return: 0 on success
*/
-#ifdef CONFIG_DM_ETH
static int fecmxc_send(struct udevice *dev, void *packet, int length)
-#else
-static int fec_send(struct eth_device *dev, void *packet, int length)
-#endif
{
unsigned int status;
u32 size;
* This routine transmits one frame. This routine only accepts
* 6-byte Ethernet addresses.
*/
-#ifdef CONFIG_DM_ETH
struct fec_priv *fec = dev_get_priv(dev);
-#else
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
-#endif
/*
* Check for valid length of data.
* @param[in] dev Our ethernet device to handle
* Return: Length of packet read
*/
-#ifdef CONFIG_DM_ETH
static int fecmxc_recv(struct udevice *dev, int flags, uchar **packetp)
-#else
-static int fec_recv(struct eth_device *dev)
-#endif
{
-#ifdef CONFIG_DM_ETH
struct fec_priv *fec = dev_get_priv(dev);
-#else
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
-#endif
struct fec_bd *rbd = &fec->rbd_base[fec->rbd_index];
unsigned long ievent;
int frame_length, len = 0;
ulong addr, size, end;
int i;
-#ifdef CONFIG_DM_ETH
*packetp = memalign(ARCH_DMA_MINALIGN, FEC_MAX_PKT_SIZE);
if (*packetp == 0) {
printf("%s: error allocating packetp\n", __func__);
return -ENOMEM;
}
-#else
- ALLOC_CACHE_ALIGN_BUFFER(uchar, buff, FEC_MAX_PKT_SIZE);
-#endif
/* Check if any critical events have happened */
ievent = readl(&fec->eth->ievent);
writel(ievent, &fec->eth->ievent);
debug("fec_recv: ievent 0x%lx\n", ievent);
if (ievent & FEC_IEVENT_BABR) {
-#ifdef CONFIG_DM_ETH
fecmxc_halt(dev);
fecmxc_init(dev);
-#else
- fec_halt(dev);
- fec_init(dev, fec->bd);
-#endif
printf("some error: 0x%08lx\n", ievent);
return 0;
}
if (ievent & FEC_IEVENT_GRA) {
/* Graceful stop complete */
if (readl(&fec->eth->x_cntrl) & 0x00000001) {
-#ifdef CONFIG_DM_ETH
fecmxc_halt(dev);
-#else
- fec_halt(dev);
-#endif
writel(~0x00000001 & readl(&fec->eth->x_cntrl),
&fec->eth->x_cntrl);
-#ifdef CONFIG_DM_ETH
fecmxc_init(dev);
-#else
- fec_init(dev, fec->bd);
-#endif
}
}
swap_packet((uint32_t *)addr, frame_length);
#endif
-#ifdef CONFIG_DM_ETH
memcpy(*packetp, (char *)addr, frame_length);
-#else
- memcpy(buff, (char *)addr, frame_length);
- net_process_received_packet(buff, frame_length);
-#endif
len = frame_length;
} else {
if (bd_status & FEC_RBD_ERR)
return bus;
}
-#ifndef CONFIG_DM_ETH
-#ifdef CONFIG_PHYLIB
-int fec_probe(struct bd_info *bd, int dev_id, uint32_t base_addr,
- struct mii_dev *bus, struct phy_device *phydev)
-#else
-static int fec_probe(struct bd_info *bd, int dev_id, uint32_t base_addr,
- struct mii_dev *bus, int phy_id)
-#endif
-{
- struct eth_device *edev;
- struct fec_priv *fec;
- unsigned char ethaddr[6];
- char mac[16];
- uint32_t start;
- int ret = 0;
-
- /* create and fill edev struct */
- edev = (struct eth_device *)malloc(sizeof(struct eth_device));
- if (!edev) {
- puts("fec_mxc: not enough malloc memory for eth_device\n");
- ret = -ENOMEM;
- goto err1;
- }
-
- fec = (struct fec_priv *)malloc(sizeof(struct fec_priv));
- if (!fec) {
- puts("fec_mxc: not enough malloc memory for fec_priv\n");
- ret = -ENOMEM;
- goto err2;
- }
-
- memset(edev, 0, sizeof(*edev));
- memset(fec, 0, sizeof(*fec));
-
- ret = fec_alloc_descs(fec);
- if (ret)
- goto err3;
-
- edev->priv = fec;
- edev->init = fec_init;
- edev->send = fec_send;
- edev->recv = fec_recv;
- edev->halt = fec_halt;
- edev->write_hwaddr = fec_set_hwaddr;
-
- fec->eth = (struct ethernet_regs *)(ulong)base_addr;
- fec->bd = bd;
-
- fec->xcv_type = CONFIG_FEC_XCV_TYPE;
-
- /* Reset chip. */
- writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_RESET, &fec->eth->ecntrl);
- start = get_timer(0);
- while (readl(&fec->eth->ecntrl) & FEC_ECNTRL_RESET) {
- if (get_timer(start) > (CONFIG_SYS_HZ * 5)) {
- printf("FEC MXC: Timeout resetting chip\n");
- goto err4;
- }
- udelay(10);
- }
-
- fec_reg_setup(fec);
- fec_set_dev_name(edev->name, dev_id);
- fec->dev_id = (dev_id == -1) ? 0 : dev_id;
- fec->bus = bus;
- fec_mii_setspeed(bus->priv);
-#ifdef CONFIG_PHYLIB
- fec->phydev = phydev;
- phy_connect_dev(phydev, edev);
- /* Configure phy */
- phy_config(phydev);
-#else
- fec->phy_id = phy_id;
-#endif
- eth_register(edev);
- /* only support one eth device, the index number pointed by dev_id */
- edev->index = fec->dev_id;
-
- if (fec_get_hwaddr(fec->dev_id, ethaddr) == 0) {
- debug("got MAC%d address from fuse: %pM\n", fec->dev_id, ethaddr);
- memcpy(edev->enetaddr, ethaddr, 6);
- if (fec->dev_id)
- sprintf(mac, "eth%daddr", fec->dev_id);
- else
- strcpy(mac, "ethaddr");
- if (!env_get(mac))
- eth_env_set_enetaddr(mac, ethaddr);
- }
- return ret;
-err4:
- fec_free_descs(fec);
-err3:
- free(fec);
-err2:
- free(edev);
-err1:
- return ret;
-}
-
-int fecmxc_initialize_multi(struct bd_info *bd, int dev_id, int phy_id,
- uint32_t addr)
-{
- uint32_t base_mii;
- struct mii_dev *bus = NULL;
-#ifdef CONFIG_PHYLIB
- struct phy_device *phydev = NULL;
-#endif
- int ret;
-
- if (CONFIG_IS_ENABLED(IMX_MODULE_FUSE)) {
- if (enet_fused((ulong)addr)) {
- printf("SoC fuse indicates Ethernet@0x%x is unavailable.\n", addr);
- return -ENODEV;
- }
- }
-
-#ifdef CONFIG_FEC_MXC_MDIO_BASE
- /*
- * The i.MX28 has two ethernet interfaces, but they are not equal.
- * Only the first one can access the MDIO bus.
- */
- base_mii = CONFIG_FEC_MXC_MDIO_BASE;
-#else
- base_mii = addr;
-#endif
- debug("eth_init: fec_probe(bd, %i, %i) @ %08x\n", dev_id, phy_id, addr);
- bus = fec_get_miibus(base_mii, dev_id);
- if (!bus)
- return -ENOMEM;
-#ifdef CONFIG_PHYLIB
- phydev = phy_find_by_mask(bus, 1 << phy_id, PHY_INTERFACE_MODE_RGMII);
- if (!phydev) {
- mdio_unregister(bus);
- free(bus);
- return -ENOMEM;
- }
- ret = fec_probe(bd, dev_id, addr, bus, phydev);
-#else
- ret = fec_probe(bd, dev_id, addr, bus, phy_id);
-#endif
- if (ret) {
-#ifdef CONFIG_PHYLIB
- free(phydev);
-#endif
- mdio_unregister(bus);
- free(bus);
- }
- return ret;
-}
-
-#ifdef CONFIG_FEC_MXC_PHYADDR
-int fecmxc_initialize(struct bd_info *bd)
-{
- return fecmxc_initialize_multi(bd, -1, CONFIG_FEC_MXC_PHYADDR,
- IMX_FEC_BASE);
-}
-#endif
-
-#ifndef CONFIG_PHYLIB
-int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int))
-{
- struct fec_priv *fec = (struct fec_priv *)dev->priv;
- fec->mii_postcall = cb;
- return 0;
-}
-#endif
-
-#else
-
static int fecmxc_read_rom_hwaddr(struct udevice *dev)
{
struct fec_priv *priv = dev_get_priv(dev);
priv->xcv_type = RGMII;
break;
default:
- priv->xcv_type = CONFIG_FEC_XCV_TYPE;
- printf("Unsupported interface type %d defaulting to %d\n",
- priv->interface, priv->xcv_type);
+ priv->xcv_type = MII100;
+ printf("Unsupported interface type %d defaulting to MII100\n",
+ priv->interface);
break;
}
.priv_auto = sizeof(struct fec_priv),
.plat_auto = sizeof(struct eth_pdata),
};
-#endif
help
The value to set the "bootfile" variable to.
+config USE_ETHPRIME
+ bool "Add an 'ethprime' environment variable"
+ help
+ The "ethprime" variable is used in some cases to control which
+ network interface is used first.
+
+config ETHPRIME
+ string "'ethprime' environment variable value"
+ depends on USE_ETHPRIME
+ help
+ The value to set the "ethprime" variable to.
+
config VERSION_VARIABLE
bool "Add a 'ver' environment variable with the U-Boot version"
help
# define CONFIG_SYS_DISCOVER_PHY
# define CONFIG_SYS_RX_ETH_BUFFER 8
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# define CONFIG_HAS_ETH1
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
# ifndef CONFIG_SYS_DISCOVER_PHY
# define FECDUPLEX FULL
#define CONFIG_SYS_DISCOVER_PHY
#define CONFIG_SYS_RX_ETH_BUFFER 8
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#define CONFIG_HAS_ETH1
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
#ifndef CONFIG_SYS_DISCOVER_PHY
#define FECDUPLEX FULL
#define CONFIG_SYS_I2C_PINMUX_SET (0x000F)
#ifdef CONFIG_MCFFEC
-# define CONFIG_NET_RETRY_COUNT 5
# define CONFIG_OVERWRITE_ETHADDR_ONCE
#endif /* FEC_ENET */
# define CONFIG_SYS_TX_ETH_BUFFER 8
# define CONFIG_SYS_FEC_BUF_USE_SRAM
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# define CONFIG_HAS_ETH1
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
# ifndef CONFIG_SYS_DISCOVER_PHY
#define CONFIG_TSEC1
#ifdef CONFIG_TSEC1
-#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 2
#endif
#ifdef CONFIG_TSEC2
-#define CONFIG_HAS_ETH1
#define CONFIG_TSEC2_NAME "TSEC1"
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define TSEC2_PHY_ADDR 0x1c
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_PHYIDX 0
#endif
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
#endif
/*
#define TSEC2_FLAGS TSEC_GIGABIT
#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-/* Options are: eTSEC[0-3] */
-#define CONFIG_ETHPRIME "eTSEC0"
#endif /* CONFIG_TSEC_ENET */
/*
/*
* Environment Configuration
*/
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#endif
#define CONFIG_IPADDR 192.168.1.253
#undef CONFIG_SYS_RAMBOOT
#endif
-#ifdef CONFIG_SYS_FSL_ERRATUM_IFC_A003399
-#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_A003399_NOR_WORKAROUND
-#endif
-#endif
-
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* End of used area in RAM */
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
-#define CONFIG_ETHPRIME "eTSEC1"
-
/* TBI PHY configuration for SGMII mode */
#define CONFIG_TSEC_TBICR_SETTINGS ( \
TBICR_PHY_RESET \
* Environment Configuration
*/
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0
#define CONFIG_SYS_TBIPA_VALUE 8
-#define CONFIG_ETHPRIME "FM1@DTSEC1"
#endif
/*
#endif
#endif
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME "FM1@DTSEC4"
-#endif
-
/*
* Dynamic MTD Partition support with mtdparts
*/
#define CONFIG_SYS_RAMBOOT
#endif
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008044
-#if defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_A008044_WORKAROUND
-#endif
-#endif
-
#define CONFIG_HWCONFIG
/* define to use L1 as initial stack */
#define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR 0x0c
#endif
#endif
-
-#define CONFIG_ETHPRIME "FM1@DTSEC4"
#endif
/*
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
#endif
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME "FM1@DTSEC3"
-#endif
-
/*
* SATA
*/
#define AQR113C_PHY_ADDR2 0x08
#endif
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME "FM1@DTSEC3"
-#endif
-
/*
* SATA
*/
#define CONFIG_LBA48
#endif
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME "FM1@DTSEC1"
-#endif
-
/*
* Environment
*/
#define CONFIG_LBA48
#endif
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_ETHPRIME "FM1@DTSEC1"
-#endif
-
/*
* USB
*/
*/
/*
- * USB configuration. We enable MUSB support, both for host and for
- * gadget. We set USB0 as peripheral and USB1 as host, based on the
- * board schematic and physical port wired to each. Then for host we
- * add mass storage support and for gadget we add both RNDIS ethernet
- * and DFU.
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
-/*
* Disable MMC DM for SPL build and can be re-enabled after adding
* DM support in SPL
*/
#endif /* CONFIG_MTD_RAW_NAND */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
#endif /* ! __CONFIG_AM335X_GUARDIAN_H */
#define CONFIG_HSMMC2_8BIT
-#ifndef CONFIG_SHC_ICT
-/*
- * In builds other than ICT, reset to retry after timeout
- * Define a timeout after which a stopped bootloader continues autoboot
- * (only works with CONFIG_RESET_TO_RETRY)
- */
-# define CONFIG_BOOT_RETRY_TIME 30
-# define CONFIG_RESET_TO_RETRY
-#endif
-
#ifndef CONFIG_SPL_BUILD
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x80200000\0" \
#undef CONFIG_DM_MMC
#undef CONFIG_TIMER
#endif
-
-#define CONFIG_NET_RETRY_COUNT 10
#endif /* ! __CONFIG_AM335X_SHC_H */
#include <configs/ti_omap3_common.h>
-/* Ethernet */
-#define CONFIG_NET_RETRY_COUNT 10
-
/* Board NAND Info. */
#ifdef CONFIG_MTD_RAW_NAND
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, \
#endif
-#ifndef CONFIG_SPL_BUILD
-/* CPSW Ethernet */
-#define CONFIG_NET_RETRY_COUNT 10
-#endif
-
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs longer aneg time at 1G */
#define CONFIG_SYS_RX_ETH_BUFFER 64
#define CONFIG_HSMMC2_8BIT
/* CPSW Ethernet */
-#define CONFIG_NET_RETRY_COUNT 10
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs longer aneg time at 1G */
/*
#define CONFIG_FEC_ENET_DEV 0
#define IMX_FEC_BASE 0x5b040000
#define CONFIG_FEC_MXC_PHYADDR 0x4
-#define CONFIG_ETHPRIME "eth0"
-#define CONFIG_FEC_XCV_TYPE RGMII
#define PHY_ANEG_TIMEOUT 20000
#endif /* __APALIS_IMX8X_H */
#include "tegra-common-usb-gadget.h"
#include "tegra-common-post.h"
-/* Reserve top 1M for secure RAM */
-#define CONFIG_ARMV7_SECURE_BASE 0xfff00000
-#define CONFIG_ARMV7_SECURE_RESERVE_SIZE 0x00100000
-
#endif /* __CONFIG_H */
#define CONSOLE_DEV "ttymxc0"
#endif
-#define CONFIG_FEC_XCV_TYPE RGMII
-
/* Framebuffer */
#define CONFIG_SYS_LDB_CLOCK 28341000
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 0
#define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
HAB_EXTRA_SETTINGS \
EXTRA_ENV_BOARD_SETTINGS
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */
-/* Define actual evaluation board type from used processor type */
-#ifdef CONFIG_AT91SAM9G20
-# define CONFIG_AT91SAM9G20EK /* It's an Atmel AT91SAM9G20 EK */
-#else
-# define CONFIG_AT91SAM9260EK /* It's an Atmel AT91SAM9260 EK */
-#endif
-
-/* Misc CPU related */
-
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-
/*
* SDRAM: 1 bank, min 32, max 128 MB
* Initialized before u-boot gets started.
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */
-#ifdef CONFIG_AT91SAM9G10
-#define CONFIG_AT91SAM9G10EK /* It's an Atmel AT91SAM9G10 EK*/
-#else
-#define CONFIG_AT91SAM9261EK /* It's an Atmel AT91SAM9261 EK*/
-#endif
-
#include <asm/hardware.h>
-#define CONFIG_ATMEL_LEGACY
-
/*
* Hardware drivers
*/
#define DM9000_DATA (CONFIG_DM9000_BASE + 4)
#define CONFIG_DM9000_USE_16BIT
#define CONFIG_DM9000_NO_SROM
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R
/* USB */
/*
* Hardware drivers
*/
-#define CONFIG_ATMEL_LEGACY
/* LCD */
#define LCD_BPP LCD_COLOR8
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-#define CONFIG_AT91SAM9M10G45EK
-
/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
/* LCD */
#define LCD_BPP LCD_COLOR8
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_ATMEL_LCD
#define CONFIG_ATMEL_LCD_RGB565
-/* board specific(not enough SRAM) */
-#define CONFIG_AT91SAM9G45_LCD_BASE 0x73E00000
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE 0x70000000
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* main clock xtal */
-#define CONFIG_ATMEL_LEGACY
-
/*
* Hardware drivers
*/
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */
/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
/*
* define CONFIG_USB_EHCI_HCD to enable USB Hi-Speed (aka 2.0)
#endif
#endif
-/*
- * USB configuration. We enable MUSB support, both for host and for
- * gadget. We set USB0 as peripheral and USB1 as host, based on the
- * board schematic and physical port wired to each. Then for host we
- * add mass storage support and for gadget we add both RNDIS ethernet
- * and DFU.
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_HOST
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_OTG
-
/* NAND support */
#ifdef CONFIG_MTD_RAW_NAND
#define GPMC_NAND_ECC_LP_x8_LAYOUT 1
/* Enable PREBOOT variable */
-/* Set ARP_TIMEOUT to 500ms */
-#define CONFIG_ARP_TIMEOUT 500UL
-
-/* Set ARP_TIMEOUT_COUNT to 3 repetitions */
-#define CONFIG_NET_RETRY_COUNT 5
-
/* BK4r1 net init sets GPIO122/PTE17 to enable Ethernet */
#define BK4_NET_INIT "run set_gpio122;"
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* Ethernet */
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_FIXED_SPEED _1000BASET
-#define CONFIG_ARP_TIMEOUT 1500UL
/* USB Configs */
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
"setcurs 1 10;lcdputs serverip; setcurs 10 10; lcdputs ${serverip};" \
"setenv stdout nc;setenv stdin nc;setenv stderr nc\0"
-/* Network defines */
-#define CONFIG_NET_RETRY_COUNT 10
-
/* Network console */
/* As stated above, the following choices are optional. */
#define CONFIG_FACTORYSET
-/* ENET Config */
-#define CONFIG_FEC_XCV_TYPE RMII
-
/* ENET1 connects to base board and MUX with ESAI */
#define CONFIG_FEC_ENET_DEV 1
#define CONFIG_FEC_MXC_PHYADDR 0x0
-#define CONFIG_ETHPRIME "eth1"
/* I2C Configuration */
#ifndef CONFIG_SPL_BUILD
#include "tegra-common-usb-gadget.h"
#include "tegra-common-post.h"
-/* Reserve top 1M for secure RAM */
-#define CONFIG_ARMV7_SECURE_BASE 0xfff00000
-#define CONFIG_ARMV7_SECURE_RESERVE_SIZE 0x00100000
-
#endif /* __CONFIG_H */
/* Networking */
#define CONFIG_FEC_MXC_PHYADDR -1
-#define CONFIG_FEC_XCV_TYPE RGMII
#define FEC_QUIRK_ENET_MAC
#endif /* __CGTQMX8_H */
#define CONFIG_SYS_NAND_ECCBYTES 14
/* NAND: SPL related configs */
-/* USB configuration */
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
/*
* Disable MMC DM for SPL build and can be re-enabled after adding
* DM support in SPL
#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
/* Network */
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 0
/* ENET1 */
/* Ethernet */
#define CONFIG_FEC_MXC_PHYADDR 0
-#define CONFIG_FEC_XCV_TYPE RGMII
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_ETHPRIME "FEC0"
-#define CONFIG_ARP_TIMEOUT 200UL
-#define CONFIG_NET_RETRY_COUNT 5
/* USB */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_DM9000_BASE 0x08000000
#define DM9000_IO (CONFIG_DM9000_BASE)
#define DM9000_DATA (CONFIG_DM9000_BASE + 4)
-#define CONFIG_NET_RETRY_COUNT 10
#endif
/*
#define CONFIG_SYS_FM2_10GEC1_PHY_ADDR 0
#define CONFIG_SYS_TBIPA_VALUE 8
-#define CONFIG_ETHPRIME "FM1@DTSEC1"
#endif
/*
* hex number here!
*/
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
-
/* serial console */
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
/* Ethernet */
#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_AT91_WANTS_COMMON_PHY
/* DFU class support */
#define CONFIG_SYS_NAND_ECCBYTES 10
#endif
-/*
- * Network & Ethernet Configuration
- */
-#ifdef CONFIG_DRIVER_TI_EMAC
-#define CONFIG_NET_RETRY_COUNT 10
-#endif
-
#ifdef CONFIG_MTD_NOR_FLASH
#define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */
#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
#ifdef CONFIG_CMD_NET
#define CONFIG_FEC_ENET_DEV 0
-#if (CONFIG_FEC_ENET_DEV == 0)
-#define CONFIG_ETHPRIME "eth0"
-#elif (CONFIG_FEC_ENET_DEV == 1)
-#define CONFIG_ETHPRIME "eth1"
-#endif
#endif
/* Environment settings */
/* Hardware drivers */
/* DM9000 */
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_DRIVER_DM9000 1
#define CONFIG_DM9000_BASE 0x2c000000
#define DM9000_IO CONFIG_DM9000_BASE
/* FEC ethernet */
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 7
-#define CONFIG_ARP_TIMEOUT 200UL
/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* Enhance our eMMC support / experience. */
#define CONFIG_HSMMC2_8BIT
-/* CPSW Ethernet */
-#define CONFIG_NET_RETRY_COUNT 10
-
/*
* Default to using SPI for environment, etc.
* 0x000000 - 0x040000 : QSPI.SPL (256KiB)
* Options *
*----------------------------------------------------------------------*/
-#define CONFIG_BOOT_RETRY_TIME -1
-#define CONFIG_RESET_TO_RETRY
-
#define STATUS_LED_ACTIVE 0
/*----------------------------------------------------------------------*
#undef CONFIG_TPM_TIS_BASE_ADDRESS
-/*
- * Select the output device: Put an 'x' prefix before one of these to disable it
- */
-
-/*
- * Video output - can normally continue after exit_boot_services has been
- * called, since output to the display does not require EFI services at that
- * point. U-Boot sets up the console memory and does its own drawing.
- */
#define CONFIG_STD_DEVICES_SETTINGS "stdin=serial\0" \
"stdout=vidconsole\0" \
"stderr=vidconsole\0"
-/*
- * Serial output with no console. Run qemu with:
- *
- * -display none -serial mon:stdio
- *
- * This will hang or fail to output on the console after exit_boot_services is
- * called.
- */
-#define xCONFIG_STD_DEVICES_SETTINGS "stdin=serial\0" \
- "stdout=serial\0" \
- "stderr=serial\0"
-
-#undef CONFIG_BOOTCOMMAND
-
-#define CONFIG_BOOTCOMMAND "part list efi 0; fatls efi 0:1"
-
#endif
#include <config_distro_bootcmd.h>
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
/* JFFS2 */
/* Ethernet */
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RMII
#define CONFIG_PHY_ID 0
#define CONFIG_MACB_SEARCH_PHY
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x08000000 /* 128 megs */
* Environment Configuration
*/
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-
/* TODO: Turn into string option and migrate to Kconfig */
#define CONFIG_HOSTNAME "gazerbeam"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_SYS_BOOTCOUNT_LE /* Use little-endian accessors */
-#define CONFIG_BOOT_RETRY_TIME -1
-#define CONFIG_RESET_TO_RETRY
-
/*
* Miscellaneous configurable options
*/
/*
* High Level Configuration Options
*/
-#define CONFIG_BOOT_RETRY_TIME 900
-#define CONFIG_BOOT_RETRY_MIN 30
-#define CONFIG_RESET_TO_RETRY
#define CONFIG_SYS_SICRH 0x00000000
#define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D)
* Ethernet setup
*/
#ifdef CONFIG_TSEC1
-#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 0x1
#endif
#ifdef CONFIG_TSEC2
-#define CONFIG_HAS_ETH1
#define CONFIG_TSEC2_NAME "TSEC1"
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define TSEC2_PHY_ADDR 0x3
#define TSEC2_FLAGS TSEC_GIGABIT
#define TSEC2_PHYIDX 0
#endif
-#define CONFIG_ETHPRIME "TSEC1"
/*
* Serial Port
/* Ethernet Configs */
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 0
#define CONFIG_EXTRA_ENV_SETTINGS \
"fi; " \
"else run netboot; fi"
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
-#define CONFIG_ETHPRIME "FEC"
-
#undef CONFIG_SYS_AUTOLOAD
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_ETHPRIME "FEC"
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* FEC*/
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
#define IMX_FEC_BASE 0x30BE0000
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_ETHPRIME "FEC"
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* FEC */
-#define CONFIG_ETHPRIME "eth0"
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
/* ENET Config */
#if defined(CONFIG_FEC_MXC)
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
#define IMX_FEC_BASE 0x30BE0000
#define CONFIG_SPL_MAX_SIZE (148 * SZ_1K)
#define CONFIG_SYS_MONITOR_LEN SZ_512K
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
#define CONFIG_SYS_UBOOT_BASE \
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
#include <config_distro_bootcmd.h>
-/* ENET */
-#if defined(CONFIG_FEC_MXC)
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_XCV_TYPE RGMII
-#endif /* CONFIG_FEC_MXC */
-
#define MEM_LAYOUT_ENV_SETTINGS \
"scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
/* USDHC */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-/* I2C */
-#define CONFIG_SYS_I2C_SPEED 400000
-
#endif /* __IMX8MN_VAR_SOM_H */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* FEC */
-#define CONFIG_ETHPRIME "eth0"
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
#endif
#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME "eth1" /* Set eqos to primary since we use its MDIO */
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 1
#define FEC_QUIRK_ENET_MAC
#include <asm/arch/imx-regs.h>
#include <config_distro_bootcmd.h>
-#define CONFIG_HAS_ETH1
-
#define CONFIG_SYS_BOOTM_LEN (32 * SZ_1M)
#define CONFIG_SPL_MAX_SIZE (152 * 1024)
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SYS_UBOOT_BASE (QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK 0x960000
#define CONFIG_SPL_BSS_START_ADDR 0x0098FC00
#define CONFIG_SPL_BSS_MAX_SIZE 0x400 /* 1 KB */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#if defined(CONFIG_NAND_BOOT)
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_DMA
#define CONFIG_SPL_NAND_MXS
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_IDENT
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x4000000 /* Put the FIT out of \
- * first 64MB boot area \
- */
-
-/* Set a redundant offset in nand FIT mtdpart. The new uuu will burn full
- * boot image (not only FIT part) to the mtdpart, so we check both two offsets
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND \
- (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8400)
-
#endif
#endif
-#define CONFIG_REMAKE_ELF
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME "eth1" /* Set eqos to primary since we use its MDIO */
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 4
#define FEC_QUIRK_ENET_MAC
#define CONFIG_MXC_UART_BASE UART3_BASE_ADDR
/* Monitor Command Prompt */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_CBSIZE 2048
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_IMX_BOOTAUX
-
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* NAND stuff */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x20000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
#endif /* CONFIG_NAND_MXS */
-#define CONFIG_SYS_I2C_SPEED 100000
-
#endif /* __IMX8MP_RSB3720_H */
/* ENET Config */
/* ENET1 */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME "FEC"
-#endif
#ifndef CONFIG_SPL_BUILD
#define BOOT_TARGET_DEVICES(func) \
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME "FEC"
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME "FEC"
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 8000000 /* 8MHz */
-/* Networking */
-#define CONFIG_FEC_XCV_TYPE RGMII
-
#endif /* __IMX8QM_MEK_H */
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 8000000 /* 8MHz */
-/* Networking */
-#define CONFIG_FEC_XCV_TYPE RGMII
-
#include <linux/stringify.h>
#endif /* __IMX8QM_ROM7720_H */
#define CONFIG_PCA953X
#endif
-/* Networking */
-#define CONFIG_FEC_XCV_TYPE RGMII
-
/* Misc configuration */
#define CONFIG_SYS_CBSIZE 2048
#define CONFIG_SYS_MAXARGS 64
/* ENET Config */
#if defined(CONFIG_FEC_MXC)
-#define CONFIG_ETHPRIME "FEC"
#define PHY_ANEG_TIMEOUT 20000
-#define CONFIG_FEC_XCV_TYPE RMII
#define CONFIG_FEC_MXC_PHYADDR 1
#define IMX_FEC_BASE 0x29950000
#define CONFIG_SYS_BOOTM_LEN SZ_64M
#define CONFIG_CQSPI_REF_CLK 133333333
-/* HyperFlash related configuration */
-#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
-
/* U-Boot general configuration */
#define EXTRA_ENV_J721S2_BOARD_SETTINGS \
"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
#include "tegra-common-usb-gadget.h"
#include "tegra-common-post.h"
-/* Reserve top 1M for secure RAM */
-#define CONFIG_ARMV7_SECURE_BASE 0xfff00000
-#define CONFIG_ARMV7_SECURE_RESERVE_SIZE 0x00100000
-
#endif /* __CONFIG_H */
/* EEprom support */
/* ethernet port connected to piggy (UEC2) */
-#define CONFIG_HAS_ETH1
#define CONFIG_UEC_ETH2
#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */
#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
"unlock=yes\0" \
""
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
/*
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
{1, {I2C_NULL_HOP} }, \
}
-/*
- * eTSEC
- */
-#ifdef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME "ethernet@2d90000"
-#endif
-
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_SMP_PEN_ADDR 0x01ee0200
#define COUNTER_FREQUENCY 8333333
/* Qman / Bman */
/* RGMII (FM1@DTESC5) is local managemant interface */
#define CONFIG_SYS_RGMII2_PHY_ADDR 0x11
-#define CONFIG_ETHPRIME "fm1-mac5"
/*
* Hardware Watchdog
/* Board and environment settings */
#define CONFIG_MXC_UART_BASE UART4_BASE
#define CONFIG_HOSTNAME "kontron-mx6ul"
-#define CONFIG_ETHPRIME "eth0"
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_SPL_MAX_SIZE (124 * SZ_1K)
#define CONFIG_SYS_MONITOR_LEN (512 * SZ_1K)
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK 0x187FF0
#define CONFIG_SPL_BSS_START_ADDR 0x00180000
#define CONFIG_SPL_BSS_MAX_SIZE SZ_8K
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
#endif
-#define CONFIG_REMAKE_ELF
-
/* ENET1 Config */
#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME "FEC"
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_OF_SYSTEM_SETUP
-
#endif
#include <config_distro_bootcmd.h>
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Miscellaneous configurable options */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Miscellaneous configurable options */
/* FEC ethernet */
-#define CONFIG_ARP_TIMEOUT 200UL
/* USB Configs */
#ifdef CONFIG_CMD_USB
#define CONFIG_SH_SCIF_CLK_FREQ get_board_sys_clk()
#define TMU_CLK_DIVIDER (4) /* 4 (default), 16, 64, 256 or 1024 */
-#define CONFIG_NFS_TIMEOUT 10000UL
-
#endif /* __KZM9G_H */
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC"
#endif
#endif
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
-
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
-
-#define CONFIG_ETHPRIME "eTSEC2"
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
#endif
/* PCIe */
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
-
#define CONFIG_DEEP_SLEEP
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-
#define CONFIG_FSL_SGMII_RISER 1
#define SGMII_RISER_PHY_OFFSET 0x1b
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
-
#define CONFIG_DEEP_SLEEP
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
-
#define CONFIG_DEEP_SLEEP
#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
#define CONFIG_SYS_I2C_DVI_ADDR 0x39
#endif
-/*
- * eTSEC
- */
-
-#ifdef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME "ethernet@2d10000"
-#endif
-
/* PCIe */
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCIE2 /* PCIE controller 2 */
#define QSGMII_PORT4_PHY_ADDR 0x7
#define FM1_10GEC1_PHY_ADDR 0x1
-
-#define CONFIG_ETHPRIME "FM1@DTSEC3"
#endif
#endif
#define FDT_SEQ_MACADDR_FROM_ENV
-#define CONFIG_ETHPRIME "FM1@DTSEC3"
-
#endif
#define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
#define FM1_10GEC1_PHY_ADDR 0x0
#define FDT_SEQ_MACADDR_FROM_ENV
-
-#define CONFIG_ETHPRIME "FM1@DTSEC3"
#endif
#endif
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
-
#endif
#define BOOT_TARGET_DEVICES(func) \
#define QSGMII2_PORT2_PHY_ADDR 0x1d
#define QSGMII2_PORT3_PHY_ADDR 0x1e
#define QSGMII2_PORT4_PHY_ADDR 0x1f
-
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
#endif
#endif
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
-
#endif
#include <asm/fsl_secure_boot.h>
#define AQ_PHY_ADDR3 0x02
#define AQ_PHY_ADDR4 0x03
#define AQR405_IRQ_MASK 0x36
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
#include <asm/fsl_secure_boot.h>
#endif
/* MAC/PHY configuration */
-#if defined(CONFIG_FSL_MC_ENET)
-#define CONFIG_ETHPRIME "DPMAC17@rgmii-id"
-#endif
/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_NXID
/* RTC */
#define CONFIG_SYS_RTC_BUS_NUM 4
-/* MAC/PHY configuration */
-#if defined(CONFIG_FSL_MC_ENET)
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
-#endif
-
/* EMC2305 */
#define I2C_MUX_CH_EMC2305 0x09
#define I2C_EMC2305_ADDR 0x4D
#define CONFIG_ESDHC_DETECT_QUIRK qixis_esdhc_detect_quirk()
#endif
-/* MAC/PHY configuration */
-#if defined(CONFIG_FSL_MC_ENET)
-#define CONFIG_ETHPRIME "DPMAC17@rgmii-id"
-#endif
-
/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define IMX_FEC_BASE FEC_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
#define CONFIG_DISCOVER_PHY
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC0"
#endif
#define CONFIG_SYS_RTC_BUS_NUM 1 /* I2C2 */
/* Ethernet */
#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
#undef CONFIG_RESET_PHY_R
/* hw-controller addresses */
*/
#define DEFAULT_ENV_IS_RW /* required for configuring default fdtfile= */
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_ARP_TIMEOUT 200
-#define CONFIG_NET_RETRY_COUNT 50
-
#define CONFIG_USB_MAX_CONTROLLER_COUNT (3 + 3)
/*
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_ARP_TIMEOUT 200
-#define CONFIG_NET_RETRY_COUNT 50
-
#define CONFIG_USB_MAX_CONTROLLER_COUNT (3 + 3)
/* USB ethernet */
/* Framebuffer and LCD */
-#define CONFIG_ETHPRIME "FEC0"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
"image=zImage\0" \
"bootz; " \
"fi;\0"
-#define CONFIG_ARP_TIMEOUT 200UL
-
/*
* Miscellaneous configurable options
*/
"fdtfile=imx53-cx9020.dtb\0" \
BOOTENV
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Miscellaneous configurable options */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Command definition */
-
-#define CONFIG_ETHPRIME "FEC0"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
"image=zImage\0" \
"bootz; " \
"fi;\0"
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Miscellaneous configurable options */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
"video-mode=" \
"lcd:800x480-24@60,monitor=lcd\0" \
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Miscellaneous configurable options */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
"echo WARNING: Could not determine dtb to use; fi; " \
"fi;\0" \
-#define CONFIG_ARP_TIMEOUT 200UL
-
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define IMX_FEC_BASE ENET2_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#if (CONFIG_FEC_ENET_DEV == 0)
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x2
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "eth0"
#elif (CONFIG_FEC_ENET_DEV == 1)
#define IMX_FEC_BASE ENET2_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "eth1"
#endif
#endif
#ifdef CONFIG_CMD_NET
#define CONFIG_FEC_ENET_DEV 1
-#if (CONFIG_FEC_ENET_DEV == 0)
-#define CONFIG_ETHPRIME "eth0"
-#elif (CONFIG_FEC_ENET_DEV == 1)
-#define CONFIG_ETHPRIME "eth1"
-#endif
#endif
#endif
/* MMC */
-#define CONFIG_ARMV7_SECURE_BASE 0x00900000
-
/*
* If we have defined the OPTEE ram size and not OPTEE it means that we were
* launched by OPTEE, because of that we shall skip all the low level
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-#define CONFIG_ARMV7_SECURE_BASE 0x2F000000
-
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#endif /* __CONFIG_H */
#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE }
/* Default baudrate can be overridden by board! */
-/* FEC Ethernet on SoC */
-#ifdef CONFIG_FEC_MXC
-#ifndef CONFIG_ETHPRIME
-#define CONFIG_ETHPRIME "FEC0"
-#endif
-#ifndef CONFIG_FEC_XCV_TYPE
-#define CONFIG_FEC_XCV_TYPE RMII
-#endif
-#endif
-
/* NAND */
#ifdef CONFIG_CMD_NAND
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#endif
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 6
/* USB Configs */
#ifdef CONFIG_CMD_NET
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "eth0"
#endif
#define CONFIG_FEC_ENET_DEV 1
# define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#endif /* CONFIG_CMD_USB */
-#if IS_ENABLED(CONFIG_FEC_MXC)
-# define CONFIG_FEC_XCV_TYPE RMII
-#endif /* CONFIG_FEC_MXC */
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"mmcdev=0\0" \
"mmcpart=2\0" \
/** Stack starting address */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0xffff0)
-/* Autoboot options */
-#define CONFIG_RESET_TO_RETRY
-#define CONFIG_BOOT_RETRY_TIME -1
-#define CONFIG_BOOT_RETRY_MIN 30
-
/** Extra environment settings */
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=20080000\0" \
/** Heap size for U-Boot */
-/* Autoboot options */
-#define CONFIG_RESET_TO_RETRY
-#define CONFIG_BOOT_RETRY_TIME -1
-#define CONFIG_BOOT_RETRY_MIN 30
-
/* AHCI support Definitions */
#ifdef CONFIG_DM_SCSI
/** Enable 48-bit SATA addressing */
#endif
/*
- * Network & Ethernet Configuration
- */
-#ifdef CONFIG_DRIVER_TI_EMAC
-#define CONFIG_NET_RETRY_COUNT 10
-#endif
-
-/*
* U-Boot general configuration
*/
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
-
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
#endif /* CONFIG_TSEC_ENET */
/*
* Networking Configuration
*/
#define CONFIG_SYS_RX_ETH_BUFFER 8
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_ARP_TIMEOUT 500 /* millisec */
/*--------------------------------------------------
* USB Configuration
/* Ethernet Configuration */
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 1
/* Framebuffer */
#define IMX_FEC_BASE ENET2_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
-#define CONFIG_FEC_XCV_TYPE RMII
#define CONFIG_MXC_UART_BASE UART6_BASE_ADDR
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME "FEC"
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 1
#define FEC_QUIRK_ENET_MAC
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE 0x70000000
#define CONFIG_SYS_SDRAM_SIZE 0x08000000
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID 0 /* ignored in arm */
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-
/*
* define CONFIG_USB_EHCI_HCD to enable USB Hi-Speed (aka 2.0)
* NB: in this case, USB 1.1 devices won't be recognized.
GENERATED_GBL_DATA_SIZE)
#endif
-#define CONFIG_ARP_TIMEOUT 200
-#define CONFIG_NET_RETRY_COUNT 50
-
#endif
*/
#ifndef CONFIG_SPL_BUILD
-/*
- * USB configuration
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
/* USB DRACO ID as default */
#define CONFIG_USBD_HS
* 0x442000 - 0x800000 : Userland
*/
-#define CONFIG_NET_RETRY_COUNT 10
-
/* NAND support */
#ifdef CONFIG_MTD_RAW_NAND
/* UBI Support */
#endif
#endif
-/* Reboot after 60 sec if bootcmd fails */
-#define CONFIG_RESET_TO_RETRY
-#define CONFIG_BOOT_RETRY_TIME 60
-
#endif /* ! __CONFIG_SIEMENS_AM33X_COMMON_H */
/* setting board specific options */
#define CONFIG_SYS_AUTOLOAD "yes"
-#define CONFIG_RESET_TO_RETRY
/* The LED PINs */
#define CONFIG_RED_LED AT91_PIN_PA9
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
-
/* serial console */
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
*
*/
#define CONFIG_RMII /* use reduced MII inteface */
-#define CONFIG_NET_RETRY_COUNT 20 /* # of DHCP/BOOTP retries */
#define CONFIG_AT91_WANTS_COMMON_PHY
/* BOOTP and DHCP options */
/* Ethernet */
#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R
#define CONFIG_AT91_WANTS_COMMON_PHY
#define CONFIG_TFTP_PORT
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
/* GPIOs and IO expander */
-#define CONFIG_ATMEL_LEGACY
-#define CONFIG_AT91_GPIO_PULLUP 1
#define CONFIG_PCA953X
#define CONFIG_SYS_I2C_PCA953X_ADDR 0x28
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x28, 16} }
/* Ethernet */
#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R
#define CONFIG_AT91_WANTS_COMMON_PHY
#define CONFIG_TFTP_PORT
#define CONFIG_ATMEL_LCD
#define CONFIG_GURNARD_SPLASH
-/* GPIOs and IO expander */
-#define CONFIG_ATMEL_LEGACY
-#define CONFIG_AT91_GPIO_PULLUP 1
-
/* UARTs/Serial console */
/* Boot options */
/* Environment settings */
/*
- * Autoboot
- *
- * After 45s of inactivity in the prompt, the board will reset.
- * Set 'bootretry' in the environment to -1 to disable this behavior
- */
-#define CONFIG_BOOT_RETRY_TIME 45
-#define CONFIG_RESET_TO_RETRY
-
-/*
* FPGA Remote Update related environment
*
* Note that since those commands access the FPGA, the HPS-to-FPGA
#define PHYS_SDRAM_1_SIZE 0x10000000
/* Ethernet on SoC (EMAC) */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_ARP_TIMEOUT 500UL
-#endif
/* The rest of the configuration is shared */
#include <configs/socfpga_common.h>
#define TSEC3_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0,1] */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
/*
* Environment
#ifdef CONFIG_CMD_NET
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "eth0"
#endif
#endif
#include <linux/sizes.h>
#include <asm/arch/stm32.h>
-#ifdef CONFIG_ARMV7_PSCI
-/* PSCI support */
-#define CONFIG_ARMV7_SECURE_BASE STM32_SYSRAM_BASE
-#define CONFIG_ARMV7_SECURE_MAX_SIZE STM32_SYSRAM_SIZE
-#endif
-
/*
* Configuration of the external SRAM memory used by U-Boot
*/
#define __CONFIG_H
/*
- * A31 specific configuration
- */
-
-#define CONFIG_ARMV7_SECURE_BASE SUNXI_SRAM_B_BASE
-#define CONFIG_ARMV7_SECURE_MAX_SIZE (64 * 1024) /* 64 KB */
-
-/*
* Include common sunxi configuration where most the settings are
*/
#include <configs/sunxi-common.h>
#define __CONFIG_H
/*
- * A20 specific configuration
- */
-
-#define CONFIG_ARMV7_SECURE_BASE SUNXI_SRAM_B_BASE
-#define CONFIG_ARMV7_SECURE_MAX_SIZE (64 * 1024) /* 64 KB */
-
-/*
* Include common sunxi configuration where most the settings are
*/
#include <configs/sunxi-common.h>
#include <asm/arch/cpu.h>
-#ifdef SUNXI_SRAM_A2_SIZE
-/*
- * If the SoC has enough SRAM A2, use that for the secure monitor.
- * Skip the first 16 KiB of SRAM A2, which is not usable, as only certain bytes
- * are writable. Reserve the last 17 KiB for the resume shim and SCP firmware.
- */
-#define CONFIG_ARMV7_SECURE_BASE (SUNXI_SRAM_A2_BASE + 16 * 1024)
-#define CONFIG_ARMV7_SECURE_MAX_SIZE (SUNXI_SRAM_A2_SIZE - 33 * 1024)
-#endif
-
/*
* Include common sunxi configuration where most the settings are
*/
#ifdef CONFIG_MACH_SUN9I
#define SDRAM_OFFSET(x) 0x2##x
#define CONFIG_SYS_SDRAM_BASE 0x20000000
-/* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here
- * since it needs to fit in with the other values. By also #defining it
- * we get warnings if the Kconfig value mismatches. */
#define CONFIG_SPL_BSS_START_ADDR 0x2ff80000
#elif defined(CONFIG_MACH_SUNIV)
#define SDRAM_OFFSET(x) 0x8##x
#define CONFIG_SYS_SDRAM_BASE 0x80000000
-/* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here
- * since it needs to fit in with the other values. By also #defining it
- * we get warnings if the Kconfig value mismatches.
- */
-#define CONFIG_SPL_STACK_R_ADDR 0x81e00000
#define CONFIG_SPL_BSS_START_ADDR 0x81f80000
#else
#define SDRAM_OFFSET(x) 0x4##x
#define CONFIG_SYS_SDRAM_BASE 0x40000000
/* V3s do not have enough memory to place code at 0x4a000000 */
-/* Note SPL_STACK_R_ADDR is set through Kconfig, we include it here
- * since it needs to fit in with the other values. By also #defining it
- * we get warnings if the Kconfig value mismatches. */
#define CONFIG_SPL_BSS_START_ADDR 0x4ff80000
#endif
/* Misc CPU related */
-/* general purpose I/O */
-#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
-
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
#include "ls1088a_common.h"
-#define CONFIG_SYS_CLK_FREQ 100000000
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
*/
/* Ethernet */
-#define CONFIG_NET_RETRY_COUNT 10
#define CONFIG_PHY_ET1011C_TX_CLK_FIX
#endif /* ! __CONFIG_TI814X_EVM_H */
#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
CONFIG_SPL_TEXT_BASE)
-#define CONFIG_NET_RETRY_COUNT 10
-
/* Since SPL did pll and ddr initialization for us,
* we don't need to do it twice.
*/
#endif
#define CONFIG_SYS_NS16550_CLK 48000000
-#ifndef CONFIG_SPL_BUILD
-/* Network defines. */
-#define CONFIG_NET_RETRY_COUNT 10
-#endif
-
/*
* SPL related defines. The Public RAM memory map the ROM defines the
* area between 0x402F0400 and 0x4030B800 as a download area and
#define CONFIG_SYS_SPI_CLK ks_clk_get_rate(KS2_CLK1_6)
/* Network Configuration */
-#define CONFIG_NET_RETRY_COUNT 32
#define CONFIG_SYS_SGMII_REFCLK_MHZ 312
#define CONFIG_SYS_SGMII_LINERATE_MHZ 1250
#define CONFIG_SYS_SGMII_RATESCALE 2
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_ARP_TIMEOUT 200UL
-
#if defined(CONFIG_TQMA6X_MMC_BOOT)
#define TQMA6_UBOOT_OFFSET SZ_1K
#ifndef __CONFIG_TQMA6_MBA6_H
#define __CONFIG_TQMA6_MBA6_H
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-
#define CONFIG_FEC_MXC_PHYADDR 0x03
#define CONFIG_MXC_UART_BASE UART2_BASE
#define __CONFIG_TQMA6_WRU4_H
/* Ethernet */
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 0x01
/* UART */
4000000, 4500000, 5000000, 5500000, \
6000000 }
-#define CONFIG_ARP_TIMEOUT 200
-#define CONFIG_NET_RETRY_COUNT 50
-
#define CONFIG_USB_MAX_CONTROLLER_COUNT 6
#define BOOT_TARGET_DEVICES(func) \
/* Ethernet */
#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_AT91_WANTS_COMMON_PHY
/* USB */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* ENET */
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 7
#define FEC_QUIRK_ENET_MAC
#define IMX_FEC_BASE 0x30BE0000
#ifdef CONFIG_SPL_BUILD
/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK 0x960000
#define CONFIG_SPL_BSS_START_ADDR 0x0098fc00
#define CONFIG_SPL_BSS_MAX_SIZE SZ_1K
#define CONFIG_POWER_PCA9450
#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SPEED 100000
#endif /* CONFIG_SPL_BUILD */
-#define CONFIG_REMAKE_ELF
-
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME "eth0" /* eqos is aliased on-module Ethernet interface */
-
-#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 7
#define FEC_QUIRK_ENET_MAC
#define CONFIG_SYS_FSL_ESDHC_NUM 1
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RMII
#define CONFIG_FEC_MXC_PHYADDR 0
/* I2C Configs */
/* Ethernet Hardware */
#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
#ifdef CONFIG_SPI_BOOT
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC"
-
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#ifndef __XILINX_VERSAL_H
#define __XILINX_VERSAL_H
-/* #define CONFIG_ARMV8_SWITCH_TO_EL1 */
-
/* Generic Interrupt Controller Definitions */
#define GICD_BASE 0xF9000000
#define GICR_BASE 0xF9080000
#ifndef __XILINX_ZYNQMP_H
#define __XILINX_ZYNQMP_H
-/* #define CONFIG_ARMV8_SWITCH_TO_EL1 */
-
/* Generic Interrupt Controller Definitions */
#define GICD_BASE 0xF9010000
#define GICC_BASE 0xF9020000
#define CONFIG_FEC_ENET_DEV 0
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_ETHPRIME "FEC"
#define CONFIG_UBOOT_SECTOR_START 0x2
#define CONFIG_UBOOT_SECTOR_COUNT 0x3fe
if NET
+config ARP_TIMEOUT
+ int "Milliseconds before trying ARP again"
+ default 5000
+
+config NET_RETRY_COUNT
+ int "Number of timeouts before giving up"
+ default 5
+ help
+ This variable defines the number of retries for network operations
+ like ARP, RARP, TFTP, or BOOTP before giving up the operation.
+
config PROT_UDP
bool "Enable generic udp framework"
help
#include "arp.h"
-#ifndef CONFIG_ARP_TIMEOUT
-/* Milliseconds before trying ARP again */
-# define ARP_TIMEOUT 5000UL
-#else
-# define ARP_TIMEOUT CONFIG_ARP_TIMEOUT
-#endif
-
-
-#ifndef CONFIG_NET_RETRY_COUNT
-# define ARP_TIMEOUT_COUNT 5 /* # of timeouts before giving up */
-#else
-# define ARP_TIMEOUT_COUNT CONFIG_NET_RETRY_COUNT
-#endif
-
struct in_addr net_arp_wait_packet_ip;
static struct in_addr net_arp_wait_reply_ip;
/* MAC address of waiting packet's destination */
t = get_timer(0);
/* check for arp timeout */
- if ((t - arp_wait_timer_start) > ARP_TIMEOUT) {
+ if ((t - arp_wait_timer_start) > CONFIG_ARP_TIMEOUT) {
arp_wait_try++;
- if (arp_wait_try >= ARP_TIMEOUT_COUNT) {
+ if (arp_wait_try >= CONFIG_NET_RETRY_COUNT) {
puts("\nARP Retry count exceeded; starting again\n");
arp_wait_try = 0;
net_set_state(NETLOOP_FAIL);
/*
* The timeout for the initial BOOTP/DHCP request used to be described by a
- * counter of fixed-length timeout periods. TIMEOUT_COUNT represents
+ * counter of fixed-length timeout periods. CONFIG_NET_RETRY_COUNT represents
* that counter
*
* Now that the timeout periods are variable (exponential backoff and retry)
* execute that many retries, and keep sending retry packets until that time
* is reached.
*/
-#ifndef CONFIG_NET_RETRY_COUNT
-# define TIMEOUT_COUNT 5 /* # of timeouts before giving up */
-#else
-# define TIMEOUT_COUNT (CONFIG_NET_RETRY_COUNT)
-#endif
-#define TIMEOUT_MS ((3 + (TIMEOUT_COUNT * 5)) * 1000)
+#define TIMEOUT_MS ((3 + (CONFIG_NET_RETRY_COUNT * 5)) * 1000)
#define PORT_BOOTPS 67 /* BOOTP server UDP port */
#define PORT_BOOTPC 68 /* BOOTP client UDP port */
#define HASHES_PER_LINE 65 /* Number of "loading" hashes per line */
#define NFS_RETRY_COUNT 30
-#ifndef CONFIG_NFS_TIMEOUT
-# define NFS_TIMEOUT 2000UL
-#else
-# define NFS_TIMEOUT CONFIG_NFS_TIMEOUT
-#endif
#define NFS_RPC_ERR 1
#define NFS_RPC_DROP 124
static unsigned long rpc_id;
static int nfs_offset = -1;
static int nfs_len;
-static ulong nfs_timeout = NFS_TIMEOUT;
+static const ulong nfs_timeout = CONFIG_NFS_TIMEOUT;
static char dirfh[NFS_FHSIZE]; /* NFSv2 / NFSv3 file handle of directory */
static char filefh[NFS3_FHSIZE]; /* NFSv2 / NFSv3 file handle */
} else {
puts("T ");
net_set_timeout_handler(nfs_timeout +
- NFS_TIMEOUT * nfs_timeout_count,
+ nfs_timeout * nfs_timeout_count,
nfs_timeout_handler);
nfs_send();
}
#include "rarp.h"
#define TIMEOUT 5000UL /* Milliseconds before trying BOOTP again */
-#ifndef CONFIG_NET_RETRY_COUNT
-#define TIMEOUT_COUNT 5 /* # of timeouts before giving up */
-#else
-#define TIMEOUT_COUNT (CONFIG_NET_RETRY_COUNT)
-#endif
int rarp_try;
*/
static void rarp_timeout_handler(void)
{
- if (rarp_try >= TIMEOUT_COUNT) {
+ if (rarp_try >= CONFIG_NET_RETRY_COUNT) {
puts("\nRetry count exceeded; starting again\n");
net_start_again();
} else {
#define WELL_KNOWN_PORT 69
/* Millisecs to timeout for lost pkt */
#define TIMEOUT 5000UL
-#ifndef CONFIG_NET_RETRY_COUNT
-/* # of timeouts before giving up */
-# define TIMEOUT_COUNT 10
-#else
-# define TIMEOUT_COUNT (CONFIG_NET_RETRY_COUNT * 2)
-#endif
/* Number of "loading" hashes per line (for checking the image size) */
#define HASHES_PER_LINE 65
#define TFTP_OACK 6
static ulong timeout_ms = TIMEOUT;
-static int timeout_count_max = TIMEOUT_COUNT;
+static int timeout_count_max = (CONFIG_NET_RETRY_COUNT * 2);
static ulong time_start; /* Record time we started tftp */
/*
* non-standard timeout behavior when initiating a TFTP transfer.
*/
ulong tftp_timeout_ms = TIMEOUT;
-int tftp_timeout_count_max = TIMEOUT_COUNT;
+int tftp_timeout_count_max = (CONFIG_NET_RETRY_COUNT * 2);
enum {
TFTP_ERR_UNDEFINED = 0,
-CONFIG_A003399_NOR_WORKAROUND
-CONFIG_A008044_WORKAROUND
-CONFIG_AM335X_USB0
CONFIG_AM335X_USB0_MODE
-CONFIG_AM335X_USB1
CONFIG_AM335X_USB1_MODE
-CONFIG_ARMV7_SECURE_BASE
-CONFIG_ARMV7_SECURE_MAX_SIZE
-CONFIG_ARMV7_SECURE_RESERVE_SIZE
-CONFIG_ARMV8_SWITCH_TO_EL1
CONFIG_ARM_GIC_BASE_ADDRESS
-CONFIG_ARP_TIMEOUT
-CONFIG_AT91SAM9260EK
-CONFIG_AT91SAM9261EK
-CONFIG_AT91SAM9G10
-CONFIG_AT91SAM9G10EK
-CONFIG_AT91SAM9G20EK
-CONFIG_AT91SAM9G20EK_2MMC
-CONFIG_AT91SAM9G45_LCD_BASE
-CONFIG_AT91SAM9M10G45EK
-CONFIG_AT91_GPIO_PULLUP
CONFIG_AT91_LED
CONFIG_AT91_WANTS_COMMON_PHY
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
-CONFIG_ATMEL_LEGACY
CONFIG_ATMEL_SPI0
CONFIG_AUTO_ZRELADDR
CONFIG_BACKSIDE_L2_CACHE
CONFIG_BOOTSCRIPT_ADDR
CONFIG_BOOTSCRIPT_COPY_RAM
CONFIG_BOOTSCRIPT_HDR_ADDR
-CONFIG_BOOT_RETRY_MIN
-CONFIG_BOOT_RETRY_TIME
-CONFIG_BPTR_VIRT_ADDR
CONFIG_BS_ADDR_DEVICE
CONFIG_BS_ADDR_RAM
CONFIG_BS_COPY_CMD
CONFIG_ESPRESSO7420
CONFIG_ET1100_BASE
CONFIG_ETHBASE
-CONFIG_ETHPRIME
CONFIG_EXTRA_CLOCK
CONFIG_EXTRA_ENV
CONFIG_EXTRA_ENV_SETTINGS
CONFIG_FEC_ENET_DEV
CONFIG_FEC_FIXED_SPEED
CONFIG_FEC_MXC_PHYADDR
-CONFIG_FEC_XCV_TYPE
CONFIG_FIXED_SDHCI_ALIGNED_BUFFER
CONFIG_FLASH_BR_PRELIM
CONFIG_FLASH_CFI_LEGACY
CONFIG_G_DNL_THOR_VENDOR_NUM
CONFIG_G_DNL_UMS_PRODUCT_NUM
CONFIG_G_DNL_UMS_VENDOR_NUM
-CONFIG_HAS_ETH0
-CONFIG_HAS_ETH1
-CONFIG_HAS_ETH2
-CONFIG_HAS_ETH3
CONFIG_HAS_FSL_DR_USB
CONFIG_HAS_FSL_MPH_USB
CONFIG_HDMI_ENCODER_I2C_ADDR
CONFIG_NAND_SPL
CONFIG_NETDEV
CONFIG_NETMASK
-CONFIG_NET_RETRY_COUNT
CONFIG_NEVER_ASSERT_ODT_TO_CPU
-CONFIG_NFS_TIMEOUT
CONFIG_NOBQFMAN
CONFIG_NORBOOT
CONFIG_NORFLASH_PS32BIT
CONFIG_RESERVED_03_BASE
CONFIG_RESERVED_04_BASE
CONFIG_RESET_PHY_R
-CONFIG_RESET_TO_RETRY
CONFIG_RESET_VECTOR_ADDRESS
CONFIG_RESTORE_FLASH
CONFIG_RMII
projects / platform / kernel / u-boot.git / commitdiff