/* flush I/D-cache */
static void cache_flush (void)
{
+#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
unsigned long i = 0;
asm ("mcr p15, 0, %0, c7, c7, 0": :"r" (i));
+#endif
}
#if defined(CONFIG_DISPLAY_CPUINFO)
int print_cpuinfo(void)
{
- char *rev;
+ char *rev = "??";
u16 devid = (readl(KW_REG_PCIE_DEVID) >> 16) & 0xffff;
u8 revid = readl(KW_REG_PCIE_REVID) & 0xff;
switch (revid) {
case 0:
- rev = "Z0";
+ if (devid == 0x6281)
+ rev = "Z0";
+ else if (devid == 0x6282)
+ rev = "A0";
+ break;
+ case 1:
+ rev = "A1";
break;
case 2:
rev = "A0";
rev = "A1";
break;
default:
- rev = "??";
break;
}
*/
#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/clk.h>
#include <asm/arch/sama5d4.h>
char *get_cpu_name()
else
return "Unknown CPU type";
}
+
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+void at91_udp_hw_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+ /* Enable UPLL clock */
+ writel(AT91_PMC_UPLLEN | AT91_PMC_BIASEN, &pmc->uckr);
+ /* Enable UDPHS clock */
+ at91_periph_clk_enable(ATMEL_ID_UDPHS);
+}
+#endif
#include <fsl_esdhc.h>
#endif
#include <tsec.h>
+#include <asm/arch/immap_ls102xa.h>
+#include <fsl_sec.h>
DECLARE_GLOBAL_DATA_PTR;
int off;
int val;
const char *sysclk_path;
+ struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+ unsigned int svr;
+ svr = in_be32(&gur->svr);
unsigned long busclk = get_bus_freq(0);
+ /* delete crypto node if not on an E-processor */
+ if (!IS_E_PROCESSOR(svr))
+ fdt_fixup_crypto_node(blob, 0);
+#if CONFIG_SYS_FSL_SEC_COMPAT >= 4
+ else {
+ ccsr_sec_t __iomem *sec;
+
+ sec = (void __iomem *)CONFIG_SYS_FSL_SEC_ADDR;
+ fdt_fixup_crypto_node(blob, sec_in32(&sec->secvid_ms));
+ }
+#endif
+
fdt_fixup_ethernet(blob);
off = fdt_node_offset_by_prop_value(blob, -1, "device_type", "cpu", 4);
do_fixup_by_compat_u32(blob, "fsl,qoriq-sysclk-2.0",
"clock-frequency", CONFIG_SYS_CLK_FREQ, 1);
+#if defined(CONFIG_DEEP_SLEEP) && defined(CONFIG_SD_BOOT)
+#define UBOOT_HEAD_LEN 0x1000
+ /*
+ * Reserved memory in SD boot deep sleep case.
+ * Second stage uboot binary and malloc space should be reserved.
+ * If the memory they occupied has not been reserved, then this
+ * space would be used by kernel and overwritten in uboot when
+ * deep sleep resume, which cause deep sleep failed.
+ * Since second uboot binary has a head, that space need to be
+ * reserved either(assuming its size is less than 0x1000).
+ */
+ off = fdt_add_mem_rsv(blob, CONFIG_SYS_TEXT_BASE - UBOOT_HEAD_LEN,
+ CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_SPL_MALLOC_SIZE +
+ UBOOT_HEAD_LEN);
+ if (off < 0)
+ printf("Failed to reserve memory for SD boot deep sleep: %s\n",
+ fdt_strerror(off));
+#endif
+
#if defined(CONFIG_FSL_ESDHC)
fdt_fixup_esdhc(blob, bd);
#endif
do_fixup_by_compat_u32(blob, "fsl, ls1021a-flexcan",
"clock-frequency", busclk / 2, 1);
+
+#ifdef CONFIG_QSPI_BOOT
+ off = fdt_node_offset_by_compat_reg(blob, FSL_IFC_COMPAT,
+ CONFIG_SYS_IFC_ADDR);
+ fdt_set_node_status(blob, off, FDT_STATUS_DISABLED, 0);
+#else
+ off = fdt_node_offset_by_compat_reg(blob, FSL_QSPI_COMPAT,
+ QSPI0_BASE_ADDR);
+ fdt_set_node_status(blob, off, FDT_STATUS_DISABLED, 0);
+ off = fdt_node_offset_by_compat_reg(blob, FSL_DSPI_COMPAT,
+ DSPI1_BASE_ADDR);
+ fdt_set_node_status(blob, off, FDT_STATUS_DISABLED, 0);
+#endif
}
#include <asm/io.h>
#include <asm/secure.h>
-unsigned long gic_dist_addr;
-
static unsigned int read_id_pfr1(void)
{
unsigned int reg;
void __weak smp_kick_all_cpus(void)
{
+ unsigned long gic_dist_addr;
+
+ gic_dist_addr = get_gicd_base_address();
+ if (gic_dist_addr == -1)
+ return;
+
kick_secondary_cpus_gic(gic_dist_addr);
}
{
unsigned int reg;
unsigned itlinesnr, i;
+ unsigned long gic_dist_addr;
/* check whether the CPU supports the security extensions */
reg = read_id_pfr1();
obj-y += ddrc.o
obj-y += slcr.o
obj-y += clk.o
+obj-y += lowlevel_init.o
obj-$(CONFIG_SPL_BUILD) += spl.o
--- /dev/null
+#
+# Copyright (C) 2013 - 2015 Xilinx, Inc. All rights reserved.
+#
+# SPDX-License-Identifier: GPL-2.0
+#
+# Allow NEON instructions (needed for lowlevel_init.S with GNU toolchain)
+PLATFORM_RELFLAGS += -mfpu=neon
#include <asm/arch/sys_proto.h>
#include <asm/arch/hardware.h>
-void lowlevel_init(void)
-{
-}
-
#define ZYNQ_SILICON_VER_MASK 0xF0000000
#define ZYNQ_SILICON_VER_SHIFT 28
*/
/* cppcheck-suppress nullPointer */
memset((void *)0, 0, 1 * 1024 * 1024);
+
+ gd->ram_size /= 2;
} else {
puts("ECC disabled ");
}
--- /dev/null
+/*
+ * Copyright (C) 2013 Xilinx, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <linux/linkage.h>
+
+ENTRY(lowlevel_init)
+
+ /* Enable the the VFP */
+ mrc p15, 0, r1, c1, c0, 2
+ orr r1, r1, #(0x3 << 20)
+ orr r1, r1, #(0x3 << 20)
+ mcr p15, 0, r1, c1, c0, 2
+ isb
+ fmrx r1, FPEXC
+ orr r1,r1, #(1<<30)
+ fmxr FPEXC, r1
+
+ /* Move back to caller */
+ mov pc, lr
+
+ENDPROC(lowlevel_init)
zynq_slcr_unlock();
/* Disable AXI interface by asserting FPGA resets */
- writel(0xFFFFFFFF, &slcr_base->fpga_rst_ctrl);
+ writel(0xF, &slcr_base->fpga_rst_ctrl);
/* Set Level Shifters DT618760 */
writel(0xA, &slcr_base->lvl_shftr_en);
mode = BOOT_DEVICE_SPI;
break;
#endif
+ case ZYNQ_BM_NAND:
+ mode = BOOT_DEVICE_NAND;
+ break;
+ case ZYNQ_BM_NOR:
+ mode = BOOT_DEVICE_NOR;
+ break;
#ifdef CONFIG_SPL_MMC_SUPPORT
case ZYNQ_BM_SD:
puts("mmc boot\n");
mode = BOOT_DEVICE_MMC1;
break;
#endif
+ case ZYNQ_BM_JTAG:
+ mode = BOOT_DEVICE_RAM;
+ break;
default:
puts("Unsupported boot mode selected\n");
hang();
EP("ep5", 5, 1024, 3, 1, 1),
EP("ep6", 6, 1024, 3, 1, 1),
};
-#elif defined(CONFIG_SAMA5D3)
+#elif defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
static struct usba_ep_data usba_udc_ep[] = {
EP("ep0", 0, 64, 1, 0, 0),
EP("ep1", 1, 1024, 3, 1, 0),
#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
#define CONFIG_SYS_FSL_SEC_COMPAT 5
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#define CONFIG_SYS_FSL_ERRATUM_A008378
#else
#error SoC not defined
#endif
+#define FSL_IFC_COMPAT "fsl,ifc"
+#define FSL_QSPI_COMPAT "fsl,ls1-qspi"
+#define FSL_DSPI_COMPAT "fsl,vf610-dspi"
+
#endif /* _ASM_ARMV7_LS102XA_CONFIG_ */
--- /dev/null
+/*
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * Dummy header file to enable CONFIG_OF_CONTROL.
+ * If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
+ * It includes <asm/arch/gpio.h> via <asm/gpio.h>, so those SoCs that enable
+ * OF_CONTROL must have arch/gpio.h.
+ */
+
+#ifndef __ASM_ARCH_LS102XA_GPIO_H_
+#define __ASM_ARCH_LS102XA_GPIO_H_
+
+#endif
#define SCFG_ETSECDMAMCR_LE_BD_FR 0xf8001a0f
#define SCFG_ETSECCMCR_GE2_CLK125 0x04000000
+#define SCFG_ETSECCMCR_GE0_CLK125 0x00000000
+#define SCFG_ETSECCMCR_GE1_CLK125 0x08000000
#define SCFG_PIXCLKCR_PXCKEN 0x80000000
#define SCFG_QSPI_CLKSEL 0xc0100000
#define CCI400_CTRLORD_TERM_BARRIER 0x00000008
#define CCI400_CTRLORD_EN_BARRIER 0
#define CCI400_SHAORD_NON_SHAREABLE 0x00000002
+#define CCI400_DVM_MESSAGE_REQ_EN 0x00000002
+#define CCI400_SNOOP_REQ_EN 0x00000001
/* CCI-400 registers */
struct ccsr_cci400 {
#define ZYNQ_I2C_BASEADDR1 0xE0005000
#define ZYNQ_SPI_BASEADDR0 0xE0006000
#define ZYNQ_SPI_BASEADDR1 0xE0007000
+#define ZYNQ_QSPI_BASEADDR 0xE000D000
+#define ZYNQ_SMC_BASEADDR 0xE000E000
+#define ZYNQ_NAND_BASEADDR 0xE1000000
#define ZYNQ_DDRC_BASEADDR 0xF8006000
#define ZYNQ_EFUSE_BASEADDR 0xF800D000
#define ZYNQ_USB_BASEADDR0 0xE0002000
/* Bootmode setting values */
#define ZYNQ_BM_MASK 0x7
+#define ZYNQ_BM_QSPI 0x1
#define ZYNQ_BM_NOR 0x2
+#define ZYNQ_BM_NAND 0x4
#define ZYNQ_BM_SD 0x5
#define ZYNQ_BM_JTAG 0x0
#endif /* CONFIG_CPU_ARM1136 */
#ifdef CONFIG_CPU_ARM926EJS
+#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
/* test and clean, page 2-23 of arm926ejs manual */
asm("0: mrc p15, 0, r15, c7, c10, 3\n\t" "bne 0b\n" : : : "memory");
/* disable write buffer as well (page 2-22) */
asm("mcr p15, 0, %0, c7, c10, 4" : : "r" (0));
+#endif
#endif /* CONFIG_CPU_ARM926EJS */
return;
}
}
#endif /* defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) */
-/*
- * update crypto node properties to a specified revision of the SEC
- * called with sec_rev == 0 if not on an E processor
- */
-#if CONFIG_SYS_FSL_SEC_COMPAT == 2 /* SEC 2.x/3.x */
-void fdt_fixup_crypto_node(void *blob, int sec_rev)
-{
- static const struct sec_rev_prop {
- u32 sec_rev;
- u32 num_channels;
- u32 channel_fifo_len;
- u32 exec_units_mask;
- u32 descriptor_types_mask;
- } sec_rev_prop_list [] = {
- { 0x0200, 4, 24, 0x07e, 0x01010ebf }, /* SEC 2.0 */
- { 0x0201, 4, 24, 0x0fe, 0x012b0ebf }, /* SEC 2.1 */
- { 0x0202, 1, 24, 0x04c, 0x0122003f }, /* SEC 2.2 */
- { 0x0204, 4, 24, 0x07e, 0x012b0ebf }, /* SEC 2.4 */
- { 0x0300, 4, 24, 0x9fe, 0x03ab0ebf }, /* SEC 3.0 */
- { 0x0301, 4, 24, 0xbfe, 0x03ab0ebf }, /* SEC 3.1 */
- { 0x0303, 4, 24, 0x97c, 0x03a30abf }, /* SEC 3.3 */
- };
- static char compat_strlist[ARRAY_SIZE(sec_rev_prop_list) *
- sizeof("fsl,secX.Y")];
- int crypto_node, sec_idx, err;
- char *p;
- u32 val;
-
- /* locate crypto node based on lowest common compatible */
- crypto_node = fdt_node_offset_by_compatible(blob, -1, "fsl,sec2.0");
- if (crypto_node == -FDT_ERR_NOTFOUND)
- return;
-
- /* delete it if not on an E-processor */
- if (crypto_node > 0 && !sec_rev) {
- fdt_del_node(blob, crypto_node);
- return;
- }
-
- /* else we got called for possible uprev */
- for (sec_idx = 0; sec_idx < ARRAY_SIZE(sec_rev_prop_list); sec_idx++)
- if (sec_rev_prop_list[sec_idx].sec_rev == sec_rev)
- break;
-
- if (sec_idx == ARRAY_SIZE(sec_rev_prop_list)) {
- puts("warning: unknown SEC revision number\n");
- return;
- }
-
- val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].num_channels);
- err = fdt_setprop(blob, crypto_node, "fsl,num-channels", &val, 4);
- if (err < 0)
- printf("WARNING: could not set crypto property: %s\n",
- fdt_strerror(err));
-
- val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].descriptor_types_mask);
- err = fdt_setprop(blob, crypto_node, "fsl,descriptor-types-mask", &val, 4);
- if (err < 0)
- printf("WARNING: could not set crypto property: %s\n",
- fdt_strerror(err));
-
- val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].exec_units_mask);
- err = fdt_setprop(blob, crypto_node, "fsl,exec-units-mask", &val, 4);
- if (err < 0)
- printf("WARNING: could not set crypto property: %s\n",
- fdt_strerror(err));
-
- val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].channel_fifo_len);
- err = fdt_setprop(blob, crypto_node, "fsl,channel-fifo-len", &val, 4);
- if (err < 0)
- printf("WARNING: could not set crypto property: %s\n",
- fdt_strerror(err));
-
- val = 0;
- while (sec_idx >= 0) {
- p = compat_strlist + val;
- val += sprintf(p, "fsl,sec%d.%d",
- (sec_rev_prop_list[sec_idx].sec_rev & 0xff00) >> 8,
- sec_rev_prop_list[sec_idx].sec_rev & 0x00ff) + 1;
- sec_idx--;
- }
- err = fdt_setprop(blob, crypto_node, "compatible", &compat_strlist, val);
- if (err < 0)
- printf("WARNING: could not set crypto property: %s\n",
- fdt_strerror(err));
-}
-#elif CONFIG_SYS_FSL_SEC_COMPAT >= 4 /* SEC4 */
-static u8 caam_get_era(void)
-{
- static const struct {
- u16 ip_id;
- u8 maj_rev;
- u8 era;
- } caam_eras[] = {
- {0x0A10, 1, 1},
- {0x0A10, 2, 2},
- {0x0A12, 1, 3},
- {0x0A14, 1, 3},
- {0x0A14, 2, 4},
- {0x0A16, 1, 4},
- {0x0A10, 3, 4},
- {0x0A11, 1, 4},
- {0x0A18, 1, 4},
- {0x0A11, 2, 5},
- {0x0A12, 2, 5},
- {0x0A13, 1, 5},
- {0x0A1C, 1, 5}
- };
-
- ccsr_sec_t __iomem *sec = (void __iomem *)CONFIG_SYS_FSL_SEC_ADDR;
- u32 secvid_ms = sec_in32(&sec->secvid_ms);
- u32 ccbvid = sec_in32(&sec->ccbvid);
- u16 ip_id = (secvid_ms & SEC_SECVID_MS_IPID_MASK) >>
- SEC_SECVID_MS_IPID_SHIFT;
- u8 maj_rev = (secvid_ms & SEC_SECVID_MS_MAJ_REV_MASK) >>
- SEC_SECVID_MS_MAJ_REV_SHIFT;
- u8 era = (ccbvid & SEC_CCBVID_ERA_MASK) >> SEC_CCBVID_ERA_SHIFT;
-
- int i;
-
- if (era) /* This is '0' prior to CAAM ERA-6 */
- return era;
-
- for (i = 0; i < ARRAY_SIZE(caam_eras); i++)
- if (caam_eras[i].ip_id == ip_id &&
- caam_eras[i].maj_rev == maj_rev)
- return caam_eras[i].era;
-
- return 0;
-}
-
-static void fdt_fixup_crypto_era(void *blob, u32 era)
-{
- int err;
- int crypto_node;
-
- crypto_node = fdt_path_offset(blob, "crypto");
- if (crypto_node < 0) {
- printf("WARNING: Missing crypto node\n");
- return;
- }
-
- err = fdt_setprop(blob, crypto_node, "fsl,sec-era", &era,
- sizeof(era));
- if (err < 0) {
- printf("ERROR: could not set fsl,sec-era property: %s\n",
- fdt_strerror(err));
- }
-}
-
-void fdt_fixup_crypto_node(void *blob, int sec_rev)
-{
- u8 era;
-
- if (!sec_rev) {
- fdt_del_node_and_alias(blob, "crypto");
- return;
- }
-
- /* Add SEC ERA information in compatible */
- era = caam_get_era();
- if (era) {
- fdt_fixup_crypto_era(blob, era);
- } else {
- printf("WARNING: Unable to get ERA for CAAM rev: %d\n",
- sec_rev);
- }
-}
-#endif
-
int fdt_fixup_phy_connection(void *blob, int offset, phy_interface_t phyc)
{
return fdt_setprop_string(blob, offset, "phy-connection-type",
* SEC (crypto unit) major compatible version determination
*/
#if defined(CONFIG_MPC83xx)
+#define CONFIG_SYS_FSL_SEC_BE
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#endif
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
+#include <asm/arch/atmel_usba_udc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <asm/arch/sama5d3_smc.h>
#ifdef CONFIG_CMD_USB
sama5d4_xplained_usb_hw_init();
#endif
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ at91_udp_hw_init();
+#endif
return 0;
}
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
#endif
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ usba_udc_probe(&pdata);
+#ifdef CONFIG_USB_ETH_RNDIS
+ usb_eth_initialize(bis);
+#endif
+#endif
+
return rc;
}
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
+#include <asm/arch/atmel_usba_udc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <asm/arch/sama5d3_smc.h>
#ifdef CONFIG_CMD_USB
sama5d4ek_usb_hw_init();
#endif
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ at91_udp_hw_init();
+#endif
return 0;
}
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
#endif
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ usba_udc_probe(&pdata);
+#ifdef CONFIG_USB_ETH_RNDIS
+ usb_eth_initialize(bis);
+#endif
+#endif
+
return rc;
}
F: configs/ls1021aqds_nor_defconfig
F: configs/ls1021aqds_ddr4_nor_defconfig
F: configs/ls1021aqds_nor_SECURE_BOOT_defconfig
+F: configs/ls1021aqds_nor_lpuart_defconfig
F: configs/ls1021aqds_sdcard_defconfig
F: configs/ls1021aqds_qspi_defconfig
F: configs/ls1021aqds_nand_defconfig
obj-y += ls1021aqds.o
obj-y += ddr.o
obj-y += eth.o
+obj-$(CONFIG_FSL_DCU_FB) += dcu.o
--- /dev/null
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * FSL DCU Framebuffer driver
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_dcu_fb.h>
+#include <i2c.h>
+#include "div64.h"
+#include "../common/diu_ch7301.h"
+#include "ls1021aqds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+unsigned int dcu_set_pixel_clock(unsigned int pixclock)
+{
+ unsigned long long div;
+
+ div = (unsigned long long)(gd->bus_clk / 1000);
+ div *= (unsigned long long)pixclock;
+ do_div(div, 1000000000);
+
+ return div;
+}
+
+int platform_dcu_init(unsigned int xres, unsigned int yres,
+ const char *port,
+ struct fb_videomode *dcu_fb_videomode)
+{
+ const char *name;
+ unsigned int pixel_format;
+ int ret;
+ u8 ch;
+
+ /* Mux I2C3+I2C4 as HSYNC+VSYNC */
+ ret = i2c_read(CONFIG_SYS_I2C_QIXIS_ADDR, QIXIS_DCU_BRDCFG5,
+ 1, &ch, 1);
+ if (ret) {
+ printf("Error: failed to read I2C @%02x\n",
+ CONFIG_SYS_I2C_QIXIS_ADDR);
+ return ret;
+ }
+ ch &= 0x1F;
+ ch |= 0xA0;
+ ret = i2c_write(CONFIG_SYS_I2C_QIXIS_ADDR, QIXIS_DCU_BRDCFG5,
+ 1, &ch, 1);
+ if (ret) {
+ printf("Error: failed to write I2C @%02x\n",
+ CONFIG_SYS_I2C_QIXIS_ADDR);
+ return ret;
+ }
+
+ if (strncmp(port, "hdmi", 4) == 0) {
+ unsigned long pixval;
+
+ name = "HDMI";
+
+ pixval = 1000000000 / dcu_fb_videomode->pixclock;
+ pixval *= 1000;
+
+ i2c_set_bus_num(CONFIG_SYS_I2C_DVI_BUS_NUM);
+ select_i2c_ch_pca9547(I2C_MUX_CH_CH7301);
+ diu_set_dvi_encoder(pixval);
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+ } else {
+ return 0;
+ }
+
+ printf("DCU: Switching to %s monitor @ %ux%u\n", name, xres, yres);
+
+ pixel_format = 32;
+ fsl_dcu_init(xres, yres, pixel_format);
+
+ return 0;
+}
#include <common.h>
#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>
+#include <asm/io.h>
#include "ddr.h"
DECLARE_GLOBAL_DATA_PTR;
}
#endif
+#if defined(CONFIG_DEEP_SLEEP)
+void board_mem_sleep_setup(void)
+{
+ void __iomem *qixis_base = (void *)QIXIS_BASE;
+
+ /* does not provide HW signals for power management */
+ clrbits_8(qixis_base + 0x21, 0x2);
+ udelay(1);
+}
+#endif
+
phys_size_t initdram(int board_type)
{
phys_size_t dram_size;
#else
dram_size = fsl_ddr_sdram_size();
#endif
+
+#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
+ fsl_dp_resume();
+#endif
+
return dram_size;
}
#include <fsl_sec.h>
#include <spl.h>
+#include "../common/sleep.h"
#include "../common/qixis.h"
#include "ls1021aqds_qixis.h"
#ifdef CONFIG_U_QE
MUX_TYPE_SD_PC_SG_SG,
};
+enum {
+ GE0_CLK125,
+ GE2_CLK125,
+ GE1_CLK125,
+};
+
int checkboard(void)
{
#ifndef CONFIG_QSPI_BOOT
#ifdef CONFIG_TSEC_ENET
out_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR);
- out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
#endif
#ifdef CONFIG_FSL_IFC
out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
#endif
+#ifdef CONFIG_FSL_DCU_FB
+ out_be32(&scfg->pixclkcr, SCFG_PIXCLKCR_PXCKEN);
+#endif
+
+ /*
+ * Enable snoop requests and DVM message requests for
+ * Slave insterface S4 (A7 core cluster)
+ */
+ out_le32(&cci->slave[4].snoop_ctrl,
+ CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
+
+ /*
+ * Set CCI-400 Slave interface S1, S2 Shareable Override Register
+ * All transactions are treated as non-shareable
+ */
+ out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
+ out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
+
/* Workaround for the issue that DDR could not respond to
* barrier transaction which is generated by executing DSB/ISB
* instruction. Set CCI-400 control override register to
* allow barrier transaction to DDR again */
out_le32(&cci->ctrl_ord, CCI400_CTRLORD_TERM_BARRIER);
+#if defined(CONFIG_DEEP_SLEEP)
+ if (is_warm_boot())
+ fsl_dp_disable_console();
+#endif
+
return 0;
}
get_clocks();
+#if defined(CONFIG_DEEP_SLEEP)
+ if (is_warm_boot())
+ fsl_dp_disable_console();
+#endif
+
preloader_console_init();
#ifdef CONFIG_SPL_I2C_SUPPORT
}
#endif
+void config_etseccm_source(int etsec_gtx_125_mux)
+{
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+
+ switch (etsec_gtx_125_mux) {
+ case GE0_CLK125:
+ out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE0_CLK125);
+ debug("etseccm set to GE0_CLK125\n");
+ break;
+
+ case GE2_CLK125:
+ out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
+ debug("etseccm set to GE2_CLK125\n");
+ break;
+
+ case GE1_CLK125:
+ out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE1_CLK125);
+ debug("etseccm set to GE1_CLK125\n");
+ break;
+
+ default:
+ printf("Error! trying to set etseccm to invalid value\n");
+ break;
+ }
+}
+
int config_board_mux(int ctrl_type)
{
u8 reg12, reg14;
switch (ctrl_type) {
case MUX_TYPE_CAN:
+ config_etseccm_source(GE2_CLK125);
reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_CAN);
break;
case MUX_TYPE_IIC2:
reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_RGMII);
break;
case MUX_TYPE_SAI:
+ config_etseccm_source(GE2_CLK125);
reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_SAI);
break;
case MUX_TYPE_SDHC:
/* Set CCI-400 control override register to
* enable barrier transaction */
out_le32(&cci->ctrl_ord, CCI400_CTRLORD_EN_BARRIER);
- /*
- * Set CCI-400 Slave interface S0, S1, S2 Shareable Override Register
- * All transactions are treated as non-shareable
- */
- out_le32(&cci->slave[0].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
- out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
- out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
return 0;
}
+#if defined(CONFIG_DEEP_SLEEP)
+void board_sleep_prepare(void)
+{
+ struct ccsr_cci400 __iomem *cci = (void *)CONFIG_SYS_CCI400_ADDR;
+
+ /* Set CCI-400 control override register to
+ * enable barrier transaction */
+ out_le32(&cci->ctrl_ord, CCI400_CTRLORD_EN_BARRIER);
+
+#ifdef CONFIG_LS102XA_NS_ACCESS
+ enable_devices_ns_access(ns_dev, ARRAY_SIZE(ns_dev));
+#endif
+}
+#endif
+
int ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
#define QIXIS_SRDS1CLK_100 0x0
+#define QIXIS_DCU_BRDCFG5 0x55
+
#endif
F: include/configs/ls1021atwr.h
F: configs/ls1021atwr_nor_defconfig
F: configs/ls1021atwr_nor_SECURE_BOOT_defconfig
+F: configs/ls1021atwr_nor_lpuart_defconfig
F: configs/ls1021atwr_sdcard_defconfig
F: configs/ls1021atwr_qspi_defconfig
int board_early_init_f(void)
{
struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+ struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
#ifdef CONFIG_TSEC_ENET
out_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR);
out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
#endif
+ /*
+ * Enable snoop requests and DVM message requests for
+ * Slave insterface S4 (A7 core cluster)
+ */
+ out_le32(&cci->slave[4].snoop_ctrl,
+ CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
+
+ /*
+ * Set CCI-400 Slave interface S1, S2 Shareable Override Register
+ * All transactions are treated as non-shareable
+ */
+ out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
+ out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
+
return 0;
}
int board_init(void)
{
- struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
-
- /*
- * Set CCI-400 Slave interface S0, S1, S2 Shareable Override Register
- * All transactions are treated as non-shareable
- */
- out_le32(&cci->slave[0].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
- out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
- out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
-
#ifndef CONFIG_SYS_FSL_NO_SERDES
fsl_serdes_init();
#ifndef CONFIG_QSPI_BOOT
# Configure RGMII-0 interface pad voltage to 1.8V
DATA 0xffd100e0 0x1b1b1b9b
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+# Dram initalization for SINGLE x16 CL=5 @ 400MHz
DATA 0xffd01400 0x43000c30 # DDR Configuration register
# bit13-0: 0xc30, (3120 DDR2 clks refresh rate)
# bit23-14: 0x0,
# bit6-4: 0x4, CL=5
# bit7: 0x0, TestMode=0 normal
# bit8: 0x0, DLL reset=0 normal
-# bit11-9: 0x6, auto-precharge write recovery ????????????
+# bit11-9: 0x6, auto-precharge write recovery
# bit12: 0x0, PD must be zero
# bit31-13: 0x0, required
#
# Boot Media configurations
-BOOT_FROM nand # change from nand to uart if building UART image
+BOOT_FROM nand
NAND_ECC_MODE default
NAND_PAGE_SIZE 0x0800
# Configure RGMII-0 interface pad voltage to 1.8V
DATA 0xffd100e0 0x1b1b1b9b
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+# Dram initalization for SINGLE x16 CL=5 @ 400MHz
DATA 0xffd01400 0x43000c30 # DDR Configuration register
# bit13-0: 0xc30, (3120 DDR2 clks refresh rate)
# bit23-14: 0x0,
-# bit24: 0x1, enable exit self refresh mode on DDR access
-# bit25: 0x1, required
+# bit24: 0x1, enable exit self refresh mode on DDR access
+# bit25: 0x1, required
# bit29-26: 0x0,
# bit31-30: 0x1,
# bit3-2: 11, Cs0size (1Gb)
# bit5-4: 00, Cs1width (x8)
# bit7-6: 11, Cs1size (1Gb)
-# bit9-8: 00, Cs2width (nonexistent
-# bit11-10: 00, Cs2size (nonexistent
-# bit13-12: 00, Cs3width (nonexistent
-# bit15-14: 00, Cs3size (nonexistent
+# bit9-8: 00, Cs2width (nonexistent)
+# bit11-10: 00, Cs2size (nonexistent)
+# bit13-12: 00, Cs3width (nonexistent)
+# bit15-14: 00, Cs3size (nonexistent)
# bit16: 0, Cs0AddrSel
# bit17: 0, Cs1AddrSel
# bit18: 0, Cs2AddrSel
# bit6-4: 0x4, CL=5
# bit7: 0x0, TestMode=0 normal
# bit8: 0x0, DLL reset=0 normal
-# bit11-9: 0x6, auto-precharge write recovery ????????????
+# bit11-9: 0x6, auto-precharge write recovery
# bit12: 0x0, PD must be zero
# bit31-13: 0x0, required
DATA 0xffd01480 0x00000001 # DDR Initialization Control
# bit0: 0x1, enable DDR init upon this register write
-DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
-DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
+DATA 0xffd20134 0x66666666 # L2 RAM Timing 0 Register
+DATA 0xffd20138 0x66666666 # L2 RAM Timing 1 Register
# End of Header extension
DATA 0x0 0x0
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
- writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
- AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
+ writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
- writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) |
- AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2),
+ writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
+ AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
&smc->cs[3].pulse);
- writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4),
+ writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
&smc->cs[3].mode);
at91_periph_clk_enable(ATMEL_ID_PIOC);
+ at91_periph_clk_enable(ATMEL_ID_PIOA);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
}
#if defined(CONFIG_SPL_BUILD)
#if defined(CONFIG_SPL_BUILD)
#include <spl.h>
#include <nand.h>
+#include <spi_flash.h>
void matrix_init(void)
{
void at91_spl_board_init(void)
{
taurus_nand_hw_init();
+ at91_spi0_hw_init(TAURUS_SPI_MASK);
/* Configure recovery button PINs */
at91_set_gpio_input(AT91_PIN_PA31, 1);
/* check if button is pressed */
if (at91_get_gpio_value(AT91_PIN_PA31) == 0) {
- u32 boot_device;
+ struct spi_flash *flash;
debug("Recovery button pressed\n");
- boot_device = spl_boot_device();
- switch (boot_device) {
-#ifdef CONFIG_SPL_NAND_SUPPORT
- case BOOT_DEVICE_NAND:
- nand_init();
- spl_nand_erase_one(0, 0);
- break;
-#endif
+ nand_init();
+ spl_nand_erase_one(0, 0);
+ flash = spi_flash_probe(CONFIG_SF_DEFAULT_BUS,
+ 0,
+ CONFIG_SF_DEFAULT_SPEED,
+ SPI_MODE_3);
+ if (!flash) {
+ puts("no flash\n");
+ } else {
+ puts("erase spi flash sector 0\n");
+ spi_flash_erase(flash, 0,
+ CONFIG_SYS_NAND_U_BOOT_SIZE);
}
}
}
return 0;
}
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+ puts("Board:\tXilinx Zynq\n");
+ return 0;
+}
+#endif
+
int board_eth_init(bd_t *bis)
{
u32 ret = 0;
#if defined(CONFIG_ZYNQ_GEM)
# if defined(CONFIG_ZYNQ_GEM0)
ret |= zynq_gem_initialize(bis, ZYNQ_GEM_BASEADDR0,
- CONFIG_ZYNQ_GEM_PHY_ADDR0, 0);
+ CONFIG_ZYNQ_GEM_PHY_ADDR0,
+ CONFIG_ZYNQ_GEM_EMIO0);
# endif
# if defined(CONFIG_ZYNQ_GEM1)
ret |= zynq_gem_initialize(bis, ZYNQ_GEM_BASEADDR1,
- CONFIG_ZYNQ_GEM_PHY_ADDR1, 0);
+ CONFIG_ZYNQ_GEM_PHY_ADDR1,
+ CONFIG_ZYNQ_GEM_EMIO1);
# endif
#endif
return ret;
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,MACH_TYPE=2068,BOARD_AXM"
-CONFIG_ARM=y
-CONFIG_TARGET_TAURUS=y
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_TAURUS=y
--- /dev/null
+CONFIG_SYS_EXTRA_OPTIONS="LPUART"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_LS1021AQDS=y
--- /dev/null
+CONFIG_SYS_EXTRA_OPTIONS="LPUART"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_LS1021ATWR=y
# Version 2 as published by the Free Software Foundation.
#
+obj-y += sec.o
obj-$(CONFIG_FSL_CAAM) += jr.o fsl_hash.o jobdesc.o error.o
obj-$(CONFIG_CMD_BLOB) += fsl_blob.o
--- /dev/null
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#if CONFIG_SYS_FSL_SEC_COMPAT == 2 || CONFIG_SYS_FSL_SEC_COMPAT >= 4
+#include <fsl_sec.h>
+#endif
+
+/*
+ * update crypto node properties to a specified revision of the SEC
+ * called with sec_rev == 0 if not on an E processor
+ */
+#if CONFIG_SYS_FSL_SEC_COMPAT == 2 /* SEC 2.x/3.x */
+void fdt_fixup_crypto_node(void *blob, int sec_rev)
+{
+ static const struct sec_rev_prop {
+ u32 sec_rev;
+ u32 num_channels;
+ u32 channel_fifo_len;
+ u32 exec_units_mask;
+ u32 descriptor_types_mask;
+ } sec_rev_prop_list[] = {
+ { 0x0200, 4, 24, 0x07e, 0x01010ebf }, /* SEC 2.0 */
+ { 0x0201, 4, 24, 0x0fe, 0x012b0ebf }, /* SEC 2.1 */
+ { 0x0202, 1, 24, 0x04c, 0x0122003f }, /* SEC 2.2 */
+ { 0x0204, 4, 24, 0x07e, 0x012b0ebf }, /* SEC 2.4 */
+ { 0x0300, 4, 24, 0x9fe, 0x03ab0ebf }, /* SEC 3.0 */
+ { 0x0301, 4, 24, 0xbfe, 0x03ab0ebf }, /* SEC 3.1 */
+ { 0x0303, 4, 24, 0x97c, 0x03a30abf }, /* SEC 3.3 */
+ };
+ static char compat_strlist[ARRAY_SIZE(sec_rev_prop_list) *
+ sizeof("fsl,secX.Y")];
+ int crypto_node, sec_idx, err;
+ char *p;
+ u32 val;
+
+ /* locate crypto node based on lowest common compatible */
+ crypto_node = fdt_node_offset_by_compatible(blob, -1, "fsl,sec2.0");
+ if (crypto_node == -FDT_ERR_NOTFOUND)
+ return;
+
+ /* delete it if not on an E-processor */
+ if (crypto_node > 0 && !sec_rev) {
+ fdt_del_node(blob, crypto_node);
+ return;
+ }
+
+ /* else we got called for possible uprev */
+ for (sec_idx = 0; sec_idx < ARRAY_SIZE(sec_rev_prop_list); sec_idx++)
+ if (sec_rev_prop_list[sec_idx].sec_rev == sec_rev)
+ break;
+
+ if (sec_idx == ARRAY_SIZE(sec_rev_prop_list)) {
+ puts("warning: unknown SEC revision number\n");
+ return;
+ }
+
+ val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].num_channels);
+ err = fdt_setprop(blob, crypto_node, "fsl,num-channels", &val, 4);
+ if (err < 0)
+ printf("WARNING: could not set crypto property: %s\n",
+ fdt_strerror(err));
+
+ val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].descriptor_types_mask);
+ err = fdt_setprop(blob, crypto_node, "fsl,descriptor-types-mask",
+ &val, 4);
+ if (err < 0)
+ printf("WARNING: could not set crypto property: %s\n",
+ fdt_strerror(err));
+
+ val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].exec_units_mask);
+ err = fdt_setprop(blob, crypto_node, "fsl,exec-units-mask", &val, 4);
+ if (err < 0)
+ printf("WARNING: could not set crypto property: %s\n",
+ fdt_strerror(err));
+
+ val = cpu_to_fdt32(sec_rev_prop_list[sec_idx].channel_fifo_len);
+ err = fdt_setprop(blob, crypto_node, "fsl,channel-fifo-len", &val, 4);
+ if (err < 0)
+ printf("WARNING: could not set crypto property: %s\n",
+ fdt_strerror(err));
+
+ val = 0;
+ while (sec_idx >= 0) {
+ p = compat_strlist + val;
+ val += sprintf(p, "fsl,sec%d.%d",
+ (sec_rev_prop_list[sec_idx].sec_rev & 0xff00) >> 8,
+ sec_rev_prop_list[sec_idx].sec_rev & 0x00ff) + 1;
+ sec_idx--;
+ }
+ err = fdt_setprop(blob, crypto_node, "compatible", &compat_strlist,
+ val);
+ if (err < 0)
+ printf("WARNING: could not set crypto property: %s\n",
+ fdt_strerror(err));
+}
+#elif CONFIG_SYS_FSL_SEC_COMPAT >= 4 /* SEC4 */
+static u8 caam_get_era(void)
+{
+ static const struct {
+ u16 ip_id;
+ u8 maj_rev;
+ u8 era;
+ } caam_eras[] = {
+ {0x0A10, 1, 1},
+ {0x0A10, 2, 2},
+ {0x0A12, 1, 3},
+ {0x0A14, 1, 3},
+ {0x0A14, 2, 4},
+ {0x0A16, 1, 4},
+ {0x0A10, 3, 4},
+ {0x0A11, 1, 4},
+ {0x0A18, 1, 4},
+ {0x0A11, 2, 5},
+ {0x0A12, 2, 5},
+ {0x0A13, 1, 5},
+ {0x0A1C, 1, 5}
+ };
+
+ ccsr_sec_t __iomem *sec = (void __iomem *)CONFIG_SYS_FSL_SEC_ADDR;
+ u32 secvid_ms = sec_in32(&sec->secvid_ms);
+ u32 ccbvid = sec_in32(&sec->ccbvid);
+ u16 ip_id = (secvid_ms & SEC_SECVID_MS_IPID_MASK) >>
+ SEC_SECVID_MS_IPID_SHIFT;
+ u8 maj_rev = (secvid_ms & SEC_SECVID_MS_MAJ_REV_MASK) >>
+ SEC_SECVID_MS_MAJ_REV_SHIFT;
+ u8 era = (ccbvid & SEC_CCBVID_ERA_MASK) >> SEC_CCBVID_ERA_SHIFT;
+
+ int i;
+
+ if (era) /* This is '0' prior to CAAM ERA-6 */
+ return era;
+
+ for (i = 0; i < ARRAY_SIZE(caam_eras); i++)
+ if (caam_eras[i].ip_id == ip_id &&
+ caam_eras[i].maj_rev == maj_rev)
+ return caam_eras[i].era;
+
+ return 0;
+}
+
+static void fdt_fixup_crypto_era(void *blob, u32 era)
+{
+ int err;
+ int crypto_node;
+
+ crypto_node = fdt_path_offset(blob, "crypto");
+ if (crypto_node < 0) {
+ printf("WARNING: Missing crypto node\n");
+ return;
+ }
+
+ err = fdt_setprop(blob, crypto_node, "fsl,sec-era", &era,
+ sizeof(era));
+ if (err < 0) {
+ printf("ERROR: could not set fsl,sec-era property: %s\n",
+ fdt_strerror(err));
+ }
+}
+
+void fdt_fixup_crypto_node(void *blob, int sec_rev)
+{
+ u8 era;
+
+ if (!sec_rev) {
+ fdt_del_node_and_alias(blob, "crypto");
+ return;
+ }
+
+ /* Add SEC ERA information in compatible */
+ era = caam_get_era();
+ if (era) {
+ fdt_fixup_crypto_era(blob, era);
+ } else {
+ printf("WARNING: Unable to get ERA for CAAM rev: %d\n",
+ sec_rev);
+ }
+}
+#endif
ddr_out32(&ddr->debug[i], regs->debug[i]);
}
}
+#ifdef CONFIG_SYS_FSL_ERRATUM_A008378
+ /* Erratum applies when accumulated ECC is used, or DBI is enabled */
+#define IS_ACC_ECC_EN(v) ((v) & 0x4)
+#define IS_DBI(v) ((((v) >> 12) & 0x3) == 0x2)
+ if (IS_ACC_ECC_EN(regs->ddr_sdram_cfg) ||
+ IS_DBI(regs->ddr_sdram_cfg_3))
+ ddr_setbits32(ddr->debug[28], 0x9 << 20);
+#endif
/*
* For RDIMMs, JEDEC spec requires clocks to be stable before reset is
DECLARE_GLOBAL_DATA_PTR;
+#ifndef CONFIG_MVGBE_PORTS
+# define CONFIG_MVGBE_PORTS {0, 0}
+#endif
+
#define MV_PHY_ADR_REQUEST 0xee
#define MVGBE_SMI_REG (((struct mvgbe_registers *)MVGBE0_BASE)->smi)
#define ZYNQ_UART_MR_PARITY_NONE 0x00000020 /* No parity mode */
struct uart_zynq {
- u32 control; /* Control Register [8:0] */
- u32 mode; /* Mode Register [10:0] */
+ u32 control; /* 0x0 - Control Register [8:0] */
+ u32 mode; /* 0x4 - Mode Register [10:0] */
u32 reserved1[4];
- u32 baud_rate_gen; /* Baud Rate Generator [15:0] */
+ u32 baud_rate_gen; /* 0x18 - Baud Rate Generator [15:0] */
u32 reserved2[4];
- u32 channel_sts; /* Channel Status [11:0] */
- u32 tx_rx_fifo; /* FIFO [15:0] or [7:0] */
- u32 baud_rate_divider; /* Baud Rate Divider [7:0] */
+ u32 channel_sts; /* 0x2c - Channel Status [11:0] */
+ u32 tx_rx_fifo; /* 0x30 - FIFO [15:0] or [7:0] */
+ u32 baud_rate_divider; /* 0x34 - Baud Rate Divider [7:0] */
};
static struct uart_zynq *uart_zynq_ports[2] = {
[1] = (struct uart_zynq *)ZYNQ_SERIAL_BASEADDR1,
};
-#if !defined(CONFIG_ZYNQ_SERIAL_BAUDRATE0)
-# define CONFIG_ZYNQ_SERIAL_BAUDRATE0 CONFIG_BAUDRATE
-#endif
-#if !defined(CONFIG_ZYNQ_SERIAL_BAUDRATE1)
-# define CONFIG_ZYNQ_SERIAL_BAUDRATE1 CONFIG_BAUDRATE
-#endif
-
-struct uart_zynq_params {
- u32 baudrate;
-};
-
-static struct uart_zynq_params uart_zynq_ports_param[2] = {
- [0].baudrate = CONFIG_ZYNQ_SERIAL_BAUDRATE0,
- [1].baudrate = CONFIG_ZYNQ_SERIAL_BAUDRATE1,
-};
-
/* Set up the baud rate in gd struct */
static void uart_zynq_serial_setbrg(const int port)
{
/* Calculation results. */
unsigned int calc_bauderror, bdiv, bgen;
unsigned long calc_baud = 0;
- unsigned long baud = uart_zynq_ports_param[port].baudrate;
+ unsigned long baud = gd->baudrate;
unsigned long clock = get_uart_clk(port);
struct uart_zynq *regs = uart_zynq_ports[port];
#define MACH_TYPE_CORVUS 2066
+#define CONFIG_MACH_TYPE MACH_TYPE_CORVUS
#define CONFIG_SYS_GENERIC_BOARD
/*
* Warning: changing CONFIG_SYS_TEXT_BASE requires
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
+#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC8
#endif
/* Ethernet */
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_GPIO_SUPPORT
-#define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14)
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_SIZE (256*1024*1024)
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
#ifndef _CONFIG_DOCKSTAR_H
#define _CONFIG_DOCKSTAR_H
+#define CONFIG_SYS_GENERIC_BOARD
+
/*
* Version number information
*/
#ifndef _CONFIG_GOFLEXHOME_H
#define _CONFIG_GOFLEXHOME_H
+#define CONFIG_SYS_GENERIC_BOARD
+
/*
* Version number information
*/
/*
- * (C) Copyright 2009
+ * (C) Copyright 2009-2014
+ * Gerald Kerma <dreagle@doukki.net>
* Marvell Semiconductor <www.marvell.com>
* Written-by: Siddarth Gore <gores@marvell.com>
*
#ifndef _CONFIG_GURUPLUG_H
#define _CONFIG_GURUPLUG_H
+#define CONFIG_SYS_GENERIC_BOARD
+
/*
* Version number information
*/
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
+ * Compression configuration
+ */
+#define CONFIG_BZIP2
+#define CONFIG_LZMA
+#define CONFIG_LZO
+
+/*
+ * Enable device tree support
+ */
+#define CONFIG_OF_LIBFDT
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+
+/*
* Commands configuration
*/
#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
#include <config_cmd_default.h>
+#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
-#define CONFIG_CMD_FAT
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PING
#define CONFIG_CMD_USB
-#define CONFIG_CMD_IDE
+#define CONFIG_CMD_FAT
/*
* mv-common.h should be defined after CMD configs since it used them
* it has to be rounded to sector size
*/
#define CONFIG_ENV_SIZE 0x20000 /* 128k */
-#define CONFIG_ENV_ADDR 0x60000
-#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
+#define CONFIG_ENV_OFFSET 0xE0000 /* env starts here */
/*
* Default environment variables
*/
-#define CONFIG_BOOTCOMMAND "setenv ethact egiga0; " \
- "${x_bootcmd_ethernet}; setenv ethact egiga1; " \
- "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\
- "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
- "bootm 0x6400000;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "x_bootcmd_ethernet=ping 192.168.2.1\0" \
- "x_bootcmd_usb=usb start\0" \
- "x_bootcmd_kernel=nand read.e 0x6400000 0x100000 0x400000\0" \
- "x_bootargs=console=ttyS0,115200\0" \
- "x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0"
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
+ "ubi part root; " \
+ "ubifsmount ubi:rootfs; " \
+ "ubifsload 0x800000 ${kernel}; " \
+ "ubifsload 0x700000 ${fdt}; " \
+ "ubifsumount; " \
+ "fdt addr 0x700000; fdt resize; fdt chosen; " \
+ "bootz 0x800000 - 0x700000"
+
+#define CONFIG_MTDPARTS \
+ "mtdparts=orion_nand:" \
+ "896K(uboot),128K(uboot_env)," \
+ "-@1M(root)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=console=ttyS0,115200\0" \
+ "mtdids=nand0=orion_nand\0" \
+ "mtdparts="CONFIG_MTDPARTS \
+ "kernel=/boot/zImage\0" \
+ "fdt=/boot/guruplug-server-plus.dtb\0" \
+ "bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw\0"
+
+#define MTDIDS_DEFAULT "nand0=orion_nand"
+
+#define MTDPARTS_DEFAULT \
+ "mtdparts="CONFIG_MTDPARTS
/*
* Ethernet Driver configuration
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
#endif /*CONFIG_MVSATA_IDE*/
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+
#define CONFIG_SYS_ALT_MEMTEST
#endif /* _CONFIG_GURUPLUG_H */
#ifndef _CONFIG_IB62x0_H
#define _CONFIG_IB62x0_H
+#define CONFIG_SYS_GENERIC_BOARD
+
/*
* Version number information
*/
#ifndef _CONFIG_ICONNECT_H
#define _CONFIG_ICONNECT_H
+#define CONFIG_SYS_GENERIC_BOARD
+
/*
* Version number information
*/
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DEEP_SLEEP
+#if defined(CONFIG_DEEP_SLEEP)
+#define CONFIG_SILENT_CONSOLE
+#endif
+
/*
* Size of malloc() pool
*/
#define CONFIG_SPL_PAD_TO 0x1c000
#define CONFIG_SYS_TEXT_BASE 0x82000000
-#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
+ CONFIG_SYS_MONITOR_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
/*
* Serial Port
*/
+#ifdef CONFIG_LPUART
+#define CONFIG_FSL_LPUART
+#define CONFIG_LPUART_32B_REG
+#else
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+#endif
#define CONFIG_BAUDRATE 115200
*/
#define I2C_MUX_PCA_ADDR_PRI 0x77
#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH_CH7301 0xC
/*
* MMC
#endif
/*
+ * Video
+ */
+#define CONFIG_FSL_DCU_FB
+
+#ifdef CONFIG_FSL_DCU_FB
+#define CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+
+#define CONFIG_FSL_DIU_CH7301
+#define CONFIG_SYS_I2C_DVI_BUS_NUM 0
+#define CONFIG_SYS_I2C_QIXIS_ADDR 0x66
+#define CONFIG_SYS_I2C_DVI_ADDR 0x75
+#endif
+
+/*
* eTSEC
*/
#define CONFIG_TSEC_ENET
#define CONFIG_SYS_QE_FW_ADDR 0x67f40000
+#ifdef CONFIG_LPUART
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \
+ "fdt_high=0xcfffffff\0" \
+ "initrd_high=0xcfffffff\0" \
+ "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=null\0"
+#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
"fdt_high=0xcfffffff\0" \
"initrd_high=0xcfffffff\0" \
"hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=null\0"
+#endif
/*
* Miscellaneous configurable options
/*
* Serial Port
*/
+#ifdef CONFIG_LPUART
+#define CONFIG_FSL_LPUART
+#define CONFIG_LPUART_32B_REG
+#else
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
+#ifdef CONFIG_LPUART
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \
+ "initrd_high=0xcfffffff\0" \
+ "fdt_high=0xcfffffff\0"
+#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
"initrd_high=0xcfffffff\0" \
"fdt_high=0xcfffffff\0"
+#endif
/*
* Miscellaneous configurable options
#ifndef _CONFIG_POGO_E02_H
#define _CONFIG_POGO_E02_H
+#define CONFIG_SYS_GENERIC_BOARD
+
/*
* Machine type definition and ID
*/
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
+#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
#endif
#define CONFIG_USB_STORAGE
#endif
+/* USB device */
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_ATMEL_USBA
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_RNDIS
+#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK"
+
#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#define CONFIG_USB_STORAGE
#endif
+/* USB device */
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_ATMEL_USBA
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_RNDIS
+#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK"
+
#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#ifndef _CONFIG_SHEEVAPLUG_H
#define _CONFIG_SHEEVAPLUG_H
+#define CONFIG_SYS_GENERIC_BOARD
+
/*
* Version number information
*/
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_FIT
#define CONFIG_SYS_GENERIC_BOARD
+#if defined(CONFIG_SPL_BUILD)
+#define CONFIG_SYS_THUMB_BUILD
+#define CONFIG_SYS_ICACHE_OFF
+#define CONFIG_SYS_DCACHE_OFF
+#endif
/*
* Warning: changing CONFIG_SYS_TEXT_BASE requires
* adapting the initial boot program.
#define TAURUS_SPI_MASK (1 << 4)
#define TAURUS_SPI_CS_PIN AT91_PIN_PA3
+#if defined(CONFIG_SPL_BUILD)
+/* SPL related */
+#undef CONFIG_SPL_OS_BOOT /* Not supported by existing map */
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+
+#define CONFIG_SF_DEFAULT_BUS 0
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#endif
+
/* load address */
#define CONFIG_SYS_LOAD_ADDR 0x22000000
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x0
-#define CONFIG_SPL_MAX_SIZE (11 * 1024)
+#define CONFIG_SPL_MAX_SIZE (14 * 1024)
#define CONFIG_SPL_STACK (16 * 1024)
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
+ CONFIG_SYS_MALLOC_LEN)
+#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
#define CONFIG_SPL_BSS_START_ADDR CONFIG_SPL_MAX_SIZE
#define CONFIG_SPL_BSS_MAX_SIZE (3 * 1024)
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_PHYLIB
# define CONFIG_PHY_MARVELL
+# define CONFIG_BOOTP_SERVERIP
+# define CONFIG_BOOTP_BOOTPATH
+# define CONFIG_BOOTP_GATEWAY
+# define CONFIG_BOOTP_HOSTNAME
+# define CONFIG_BOOTP_MAY_FAIL
+# if !defined(CONFIG_ZYNQ_GEM_EMIO0)
+# define CONFIG_ZYNQ_GEM_EMIO0 0
+# endif
+# if !defined(CONFIG_ZYNQ_GEM_EMIO1)
+# define CONFIG_ZYNQ_GEM_EMIO1 0
+# endif
#endif
/* SPI */
# define CONFIG_USB_ULPI
# define CONFIG_EHCI_IS_TDI
# define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
+# define CONFIG_CI_UDC /* ChipIdea CI13xxx UDC */
+# define CONFIG_USB_GADGET
+# define CONFIG_USB_GADGET_DUALSPEED
+# define CONFIG_USBDOWNLOAD_GADGET
+# define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000
+# define DFU_DEFAULT_POLL_TIMEOUT 300
+# define CONFIG_DFU_FUNCTION
+# define CONFIG_DFU_RAM
+# define CONFIG_USB_GADGET_VBUS_DRAW 2
+# define CONFIG_G_DNL_VENDOR_NUM 0x03FD
+# define CONFIG_G_DNL_PRODUCT_NUM 0x0300
+# define CONFIG_G_DNL_MANUFACTURER "Xilinx"
+# define CONFIG_USB_GADGET
+# define CONFIG_USB_CABLE_CHECK
+# define CONFIG_CMD_DFU
+# define CONFIG_CMD_THOR_DOWNLOAD
+# define CONFIG_THOR_FUNCTION
+# define DFU_ALT_INFO_RAM \
+ "dfu_ram_info=" \
+ "set dfu_alt_info " \
+ "${kernel_image} ram 0x3000000 0x500000\\\\;" \
+ "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
+ "${ramdisk_image} ram 0x2000000 0x600000\0" \
+ "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
+ "thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
+
+# if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
+# define CONFIG_DFU_MMC
+# define DFU_ALT_INFO_MMC \
+ "dfu_mmc_info=" \
+ "set dfu_alt_info " \
+ "${kernel_image} fat 0 1\\\\;" \
+ "${devicetree_image} fat 0 1\\\\;" \
+ "${ramdisk_image} fat 0 1\0" \
+ "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \
+ "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0"
+
+# define DFU_ALT_INFO \
+ DFU_ALT_INFO_RAM \
+ DFU_ALT_INFO_MMC
+# else
+# define DFU_ALT_INFO \
+ DFU_ALT_INFO_RAM
+# endif
+#endif
+
+#if !defined(DFU_ALT_INFO)
+# define DFU_ALT_INFO
#endif
#if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB)
# define CONFIG_DOS_PARTITION
# define CONFIG_CMD_EXT4
# define CONFIG_CMD_EXT4_WRITE
+# define CONFIG_CMD_FS_GENERIC
#endif
#define CONFIG_SYS_I2C_ZYNQ
# define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */
#endif
-#define CONFIG_BOOTP_SERVERIP
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_MAY_FAIL
-
/* Total Size of Environment Sector */
#define CONFIG_ENV_SIZE (128 << 10)
"cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
"bootm ${load_addr}\0" \
"sdboot=echo Copying FIT from SD to RAM... && " \
- "fatload mmc 0 ${load_addr} ${fit_image} && " \
+ "load mmc 0 ${load_addr} ${fit_image} && " \
"bootm ${load_addr}\0" \
"jtagboot=echo TFTPing FIT to RAM... && " \
"tftpboot ${load_addr} ${fit_image} && " \
"bootm ${load_addr}\0" \
"usbboot=if usb start; then " \
"echo Copying FIT from USB to RAM... && " \
- "fatload usb 0 ${load_addr} ${fit_image} && " \
+ "load usb 0 ${load_addr} ${fit_image} && " \
"bootm ${load_addr}\0" \
- "fi\0"
+ "fi\0" \
+ DFU_ALT_INFO
#define CONFIG_BOOTCOMMAND "run $modeboot"
#define CONFIG_BOOTDELAY 3 /* -1 to Disable autoboot */
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_SYS_LONGHELP
#define CONFIG_CLOCKS
#define CONFIG_CMD_CLK
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x1000)
-#define CONFIG_SYS_MALLOC_LEN 0x400000
+#define CONFIG_SYS_MALLOC_LEN 0xC00000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_MALLOC_LEN
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
#ifdef CONFIG_SYS_FSL_DDR_LE
#define ddr_in32(a) in_le32(a)
#define ddr_out32(a, v) out_le32(a, v)
+#define ddr_setbits32(a, v) setbits_le32(a, v)
+#define ddr_clrbits32(a, v) clrbits_le32(a, v)
+#define ddr_clrsetbits32(a, clear, set) clrsetbits_le32(a, clear, set)
#else
#define ddr_in32(a) in_be32(a)
#define ddr_out32(a, v) out_be32(a, v)
+#define ddr_setbits32(a, v) setbits_be32(a, v)
+#define ddr_clrbits32(a, v) clrbits_be32(a, v)
+#define ddr_clrsetbits32(a, clear, set) clrsetbits_be32(a, clear, set)
#endif
#define _DDR_ADDR CONFIG_SYS_FSL_DDR_ADDR
projects / platform / kernel / u-boot.git / commitdiff