Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
MS7720SE SH7720
+ R0P77520000RZ SH7752
R0P77570030RL SH7757
R0P77850011RL SH7785
VERSION = 2013
PATCHLEVEL = 01
SUBLEVEL =
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
ifneq "$(SUBLEVEL)" ""
U_BOOT_VERSION = $(VERSION).$(PATCHLEVEL).$(SUBLEVEL)$(EXTRAVERSION)
else
@rm -f $(obj)nand_spl/{u-boot-nand_spl.lds,u-boot-spl,u-boot-spl.map}
@rm -f $(obj)spl/{u-boot-spl,u-boot-spl.bin,u-boot-spl.map}
@rm -f $(obj)spl/{u-boot-spl.lds,u-boot.lst}
- @rm -f $(obj)MLO
+ @rm -f $(obj)MLO MLO.byteswap
@rm -f $(obj)SPL
@rm -f $(obj)tools/xway-swap-bytes
@rm -f $(obj)arch/powerpc/cpu/mpc824x/bedbug_603e.c
boot loader that has already initialized the UART. Define this
variable to flush the UART at init time.
+ CONFIG_SYS_NS16550_BROKEN_TEMT
+
+ 16550 UART set the Transmitter Empty (TEMT) Bit when all output
+ has finished and the transmitter is totally empty. U-Boot waits
+ for this bit to be set to initialize the serial console. On some
+ broken platforms this bit is not set in SPL making U-Boot to
+ hang while waiting for TEMT. Define this option to avoid it.
+
- Console Interface:
Depending on board, define exactly one serial port
CONFIG_CMD_LOADS loads
CONFIG_CMD_MD5SUM print md5 message digest
(requires CONFIG_CMD_MEMORY and CONFIG_MD5)
+ CONFIG_CMD_MEMINFO * Display detailed memory information
CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, loopw, mtest
CONFIG_CMD_MISC Misc functions like sleep etc
run-time determined information about the hardware to the
environment. These will be named board_name, board_rev.
+ CONFIG_DELAY_ENVIRONMENT
+
+ Normally the environment is loaded when the board is
+ intialised so that it is available to U-Boot. This inhibits
+ that so that the environment is not available until
+ explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
+ this is instead controlled by the value of
+ /config/load-environment.
+
- DataFlash Support:
CONFIG_HAS_DATAFLASH
CONFIG_SF_DEFAULT_MODE (see include/spi.h)
CONFIG_SF_DEFAULT_SPEED in Hz
+ CONFIG_CMD_SF_TEST
+
+ Define this option to include a destructive SPI flash
+ test ('sf test').
+
- SystemACE Support:
CONFIG_SYSTEMACE
space for already greatly restricted images, including but not
limited to NAND_SPL configurations.
+- CONFIG_DISPLAY_BOARDINFO
+ Display information about the board that U-Boot is running on
+ when U-Boot starts up. The board function checkboard() is called
+ to do this.
+
+- CONFIG_DISPLAY_BOARDINFO_LATE
+ Similar to the previous option, but display this information
+ later, once stdio is running and output goes to the LCD, if
+ present.
+
Low Level (hardware related) configuration options:
---------------------------------------------------
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
-
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _image_copy_end_ofs
add r2, r0, r3 /* r2 <- source end address */
add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
- b clear_bss
+ bx lr
+
+#endif
+
+relocate_done:
+
+ bx lr
+
+#ifndef CONFIG_SPL_BUILD
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
.word __rel_dyn_end - _start
_dynsym_start_ofs:
.word __dynsym_start - _start
-#endif
-clear_bss:
-#ifdef CONFIG_SPL_BUILD
- /* No relocation for SPL */
- ldr r0, =__bss_start
- ldr r1, =__bss_end__
-#else
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
#endif
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
-_nand_boot_ofs:
- .word nand_boot
-#else
-jump_2_ram:
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
+ bx lr
/*
*************************************************************************
*/
bl lowlevel_init /* go setup pll,mux,memory */
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
skip_hw_init:
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-#ifndef CONFIG_NAND_SPL
- bl coloured_LED_init
- bl red_led_on
-#endif
-#endif
+relocate_done:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr pc, _nand_boot
-
-_nand_boot: .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
+ bx lr
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
.word mmu_table
#endif
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ mov pc, lr
+
#ifndef CONFIG_NAND_SPL
/*
* we assume that cache operation is done before. (eg. cleanup_before_linux())
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
- bl coloured_LED_init
- bl red_led_on
-#endif
+relocate_done:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
mov pc, lr
-_board_init_r_ofs:
- .word board_init_r - _start
-
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ mov pc, lr
+
/*
*************************************************************************
*
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
+relocate_done:
-_nand_boot_ofs:
- .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
mov pc, lr
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ mov pc, lr
+
/*
*************************************************************************
*
#include <config.h>
#include <version.h>
-#if defined(CONFIG_OMAP1510)
-#include <./configs/omap1510.h>
-#endif
-
/*
*************************************************************************
*
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
+relocate_done:
-_nand_boot_ofs:
- .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
mov pc, lr
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ mov pc, lr
+
/*
*************************************************************************
*
}
#endif
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+void at91_uhp_hw_init(void)
+{
+ /* Enable VBus on UHP ports */
+ at91_set_pio_output(AT91_PIO_PORTD, 18, 0); /* port A */
+ at91_set_pio_output(AT91_PIO_PORTD, 19, 0); /* port B */
+#if defined(CONFIG_USB_OHCI_NEW)
+ /* port C is OHCI only */
+ at91_set_pio_output(AT91_PIO_PORTD, 20, 0); /* port C */
+#endif
+}
+#endif
+
#ifdef CONFIG_MACB
void at91_macb_hw_init(void)
{
#define MPP_CTRL(i) (KW_MPP_BASE + (i* 4))
#define MPP_NR_REGS (1 + MPP_MAX/8)
-void kirkwood_mpp_conf(u32 *mpp_list, u32 *mpp_save)
+void kirkwood_mpp_conf(const u32 *mpp_list, u32 *mpp_save)
{
u32 mpp_ctrl[MPP_NR_REGS];
unsigned int variant_mask;
#include <common.h>
#include <version.h>
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#elif defined(CONFIG_OMAP730)
-#include <./configs/omap730.h>
-#endif
-
/*
*************************************************************************
*
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
-#ifdef CONFIG_NAND_SPL /* deprecated, use instead CONFIG_SPL_BUILD */
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
-#else
-#ifdef CONFIG_SPL_BUILD
- ldr sp, =(CONFIG_SPL_STACK)
-#else
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
-#endif
-#endif
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
sub r9, r6, r0 /* r9 <- relocation offset */
cmp r0, r6
- moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ moveq r9, #0 /* no relocation. offset(r9) = 0 */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifdef CONFIG_SPL_BUILD
- /* No relocation for SPL */
- ldr r0, =__bss_start
- ldr r1, =__bss_end__
-#else
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
-#endif
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
-#ifndef CONFIG_SPL_BUILD
- bl coloured_LED_init
- bl red_led_on
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
+relocate_done:
-_nand_boot_ofs:
- .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- ldr r1, _TEXT_BASE
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
+ bx lr
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
.word __rel_dyn_end - _start
_dynsym_start_ofs:
.word __dynsym_start - _start
+
#endif
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ bx lr
+
/*
*************************************************************************
*
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-#endif
-
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr pc, _nand_boot
+relocate_done:
-_nand_boot: .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
mov pc, lr
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
-
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ mov pc, lr
+
/*
*************************************************************************
*
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
- bl coloured_LED_init
- bl red_led_on
-#endif
+relocate_done:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_NAND_SPL
- ldr r0, _nand_boot_ofs
- mov pc, r0
-
-_nand_boot_ofs:
- .word nand_boot
-#else
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
+ bx lr
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ mov pc, lr
+
/*
*************************************************************************
*
return exynos_get_pll_clk(pllreg, r, k);
}
+/* exynos4x12: return pll clock frequency */
+static unsigned long exynos4x12_get_pll_clk(int pllreg)
+{
+ struct exynos4x12_clock *clk =
+ (struct exynos4x12_clock *)samsung_get_base_clock();
+ unsigned long r, k = 0;
+
+ switch (pllreg) {
+ case APLL:
+ r = readl(&clk->apll_con0);
+ break;
+ case MPLL:
+ r = readl(&clk->mpll_con0);
+ break;
+ case EPLL:
+ r = readl(&clk->epll_con0);
+ k = readl(&clk->epll_con1);
+ break;
+ case VPLL:
+ r = readl(&clk->vpll_con0);
+ k = readl(&clk->vpll_con1);
+ break;
+ default:
+ printf("Unsupported PLL (%d)\n", pllreg);
+ return 0;
+ }
+
+ return exynos_get_pll_clk(pllreg, r, k);
+}
+
/* exynos5: return pll clock frequency */
static unsigned long exynos5_get_pll_clk(int pllreg)
{
return armclk;
}
+/* exynos4x12: return ARM clock frequency */
+static unsigned long exynos4x12_get_arm_clk(void)
+{
+ struct exynos4x12_clock *clk =
+ (struct exynos4x12_clock *)samsung_get_base_clock();
+ unsigned long div;
+ unsigned long armclk;
+ unsigned int core_ratio;
+ unsigned int core2_ratio;
+
+ div = readl(&clk->div_cpu0);
+
+ /* CORE_RATIO: [2:0], CORE2_RATIO: [30:28] */
+ core_ratio = (div >> 0) & 0x7;
+ core2_ratio = (div >> 28) & 0x7;
+
+ armclk = get_pll_clk(APLL) / (core_ratio + 1);
+ armclk /= (core2_ratio + 1);
+
+ return armclk;
+}
+
/* exynos5: return ARM clock frequency */
static unsigned long exynos5_get_arm_clk(void)
{
return pclk;
}
+/* exynos4x12: return pwm clock frequency */
+static unsigned long exynos4x12_get_pwm_clk(void)
+{
+ unsigned long pclk, sclk;
+ unsigned int ratio;
+
+ sclk = get_pll_clk(MPLL);
+ ratio = 8;
+
+ pclk = sclk / (ratio + 1);
+
+ return pclk;
+}
+
/* exynos5: return pwm clock frequency */
static unsigned long exynos5_get_pwm_clk(void)
{
return uclk;
}
+/* exynos4x12: return uart clock frequency */
+static unsigned long exynos4x12_get_uart_clk(int dev_index)
+{
+ struct exynos4x12_clock *clk =
+ (struct exynos4x12_clock *)samsung_get_base_clock();
+ unsigned long uclk, sclk;
+ unsigned int sel;
+ unsigned int ratio;
+
+ /*
+ * CLK_SRC_PERIL0
+ * UART0_SEL [3:0]
+ * UART1_SEL [7:4]
+ * UART2_SEL [8:11]
+ * UART3_SEL [12:15]
+ * UART4_SEL [16:19]
+ */
+ sel = readl(&clk->src_peril0);
+ sel = (sel >> (dev_index << 2)) & 0xf;
+
+ if (sel == 0x6)
+ sclk = get_pll_clk(MPLL);
+ else if (sel == 0x7)
+ sclk = get_pll_clk(EPLL);
+ else if (sel == 0x8)
+ sclk = get_pll_clk(VPLL);
+ else
+ return 0;
+
+ /*
+ * CLK_DIV_PERIL0
+ * UART0_RATIO [3:0]
+ * UART1_RATIO [7:4]
+ * UART2_RATIO [8:11]
+ * UART3_RATIO [12:15]
+ * UART4_RATIO [16:19]
+ */
+ ratio = readl(&clk->div_peril0);
+ ratio = (ratio >> (dev_index << 2)) & 0xf;
+
+ uclk = sclk / (ratio + 1);
+
+ return uclk;
+}
+
/* exynos5: return uart clock frequency */
static unsigned long exynos5_get_uart_clk(int dev_index)
{
return uclk;
}
+static unsigned long exynos4_get_mmc_clk(int dev_index)
+{
+ struct exynos4_clock *clk =
+ (struct exynos4_clock *)samsung_get_base_clock();
+ unsigned long uclk, sclk;
+ unsigned int sel, ratio, pre_ratio;
+ int shift;
+
+ sel = readl(&clk->src_fsys);
+ sel = (sel >> (dev_index << 2)) & 0xf;
+
+ if (sel == 0x6)
+ sclk = get_pll_clk(MPLL);
+ else if (sel == 0x7)
+ sclk = get_pll_clk(EPLL);
+ else if (sel == 0x8)
+ sclk = get_pll_clk(VPLL);
+ else
+ return 0;
+
+ switch (dev_index) {
+ case 0:
+ case 1:
+ ratio = readl(&clk->div_fsys1);
+ pre_ratio = readl(&clk->div_fsys1);
+ break;
+ case 2:
+ case 3:
+ ratio = readl(&clk->div_fsys2);
+ pre_ratio = readl(&clk->div_fsys2);
+ break;
+ case 4:
+ ratio = readl(&clk->div_fsys3);
+ pre_ratio = readl(&clk->div_fsys3);
+ break;
+ default:
+ return 0;
+ }
+
+ if (dev_index == 1 || dev_index == 3)
+ shift = 16;
+
+ ratio = (ratio >> shift) & 0xf;
+ pre_ratio = (pre_ratio >> (shift + 8)) & 0xff;
+ uclk = (sclk / (ratio + 1)) / (pre_ratio + 1);
+
+ return uclk;
+}
+
+static unsigned long exynos5_get_mmc_clk(int dev_index)
+{
+ struct exynos5_clock *clk =
+ (struct exynos5_clock *)samsung_get_base_clock();
+ unsigned long uclk, sclk;
+ unsigned int sel, ratio, pre_ratio;
+ int shift;
+
+ sel = readl(&clk->src_fsys);
+ sel = (sel >> (dev_index << 2)) & 0xf;
+
+ if (sel == 0x6)
+ sclk = get_pll_clk(MPLL);
+ else if (sel == 0x7)
+ sclk = get_pll_clk(EPLL);
+ else if (sel == 0x8)
+ sclk = get_pll_clk(VPLL);
+ else
+ return 0;
+
+ switch (dev_index) {
+ case 0:
+ case 1:
+ ratio = readl(&clk->div_fsys1);
+ pre_ratio = readl(&clk->div_fsys1);
+ break;
+ case 2:
+ case 3:
+ ratio = readl(&clk->div_fsys2);
+ pre_ratio = readl(&clk->div_fsys2);
+ break;
+ default:
+ return 0;
+ }
+
+ if (dev_index == 1 || dev_index == 3)
+ shift = 16;
+
+ ratio = (ratio >> shift) & 0xf;
+ pre_ratio = (pre_ratio >> (shift + 8)) & 0xff;
+ uclk = (sclk / (ratio + 1)) / (pre_ratio + 1);
+
+ return uclk;
+}
+
/* exynos4: set the mmc clock */
static void exynos4_set_mmc_clk(int dev_index, unsigned int div)
{
* MMC0_PRE_RATIO [15:8], MMC1_PRE_RATIO [31:24]
* CLK_DIV_FSYS2
* MMC2_PRE_RATIO [15:8], MMC3_PRE_RATIO [31:24]
+ * CLK_DIV_FSYS3
+ * MMC4_PRE_RATIO [15:8]
+ */
+ if (dev_index < 2) {
+ addr = (unsigned int)&clk->div_fsys1;
+ } else if (dev_index == 4) {
+ addr = (unsigned int)&clk->div_fsys3;
+ dev_index -= 4;
+ } else {
+ addr = (unsigned int)&clk->div_fsys2;
+ dev_index -= 2;
+ }
+
+ val = readl(addr);
+ val &= ~(0xff << ((dev_index << 4) + 8));
+ val |= (div & 0xff) << ((dev_index << 4) + 8);
+ writel(val, addr);
+}
+
+/* exynos4x12: set the mmc clock */
+static void exynos4x12_set_mmc_clk(int dev_index, unsigned int div)
+{
+ struct exynos4x12_clock *clk =
+ (struct exynos4x12_clock *)samsung_get_base_clock();
+ unsigned int addr;
+ unsigned int val;
+
+ /*
+ * CLK_DIV_FSYS1
+ * MMC0_PRE_RATIO [15:8], MMC1_PRE_RATIO [31:24]
+ * CLK_DIV_FSYS2
+ * MMC2_PRE_RATIO [15:8], MMC3_PRE_RATIO [31:24]
*/
if (dev_index < 2) {
addr = (unsigned int)&clk->div_fsys1;
*/
cfg = readl(&clk->src_disp1_0);
cfg &= ~(0xf);
- cfg |= 0x8;
+ cfg |= 0x6;
writel(cfg, &clk->src_disp1_0);
/*
{
if (cpu_is_exynos5())
return exynos5_get_pll_clk(pllreg);
- else
+ else {
+ if (proid_is_exynos4412())
+ return exynos4x12_get_pll_clk(pllreg);
return exynos4_get_pll_clk(pllreg);
+ }
}
unsigned long get_arm_clk(void)
{
if (cpu_is_exynos5())
return exynos5_get_arm_clk();
- else
+ else {
+ if (proid_is_exynos4412())
+ return exynos4x12_get_arm_clk();
return exynos4_get_arm_clk();
+ }
}
unsigned long get_i2c_clk(void)
{
if (cpu_is_exynos5())
return exynos5_get_pwm_clk();
- else
+ else {
+ if (proid_is_exynos4412())
+ return exynos4x12_get_pwm_clk();
return exynos4_get_pwm_clk();
+ }
}
unsigned long get_uart_clk(int dev_index)
{
if (cpu_is_exynos5())
return exynos5_get_uart_clk(dev_index);
- else
+ else {
+ if (proid_is_exynos4412())
+ return exynos4x12_get_uart_clk(dev_index);
return exynos4_get_uart_clk(dev_index);
+ }
+}
+
+unsigned long get_mmc_clk(int dev_index)
+{
+ if (cpu_is_exynos5())
+ return exynos5_get_mmc_clk(dev_index);
+ else
+ return exynos4_get_mmc_clk(dev_index);
}
void set_mmc_clk(int dev_index, unsigned int div)
{
if (cpu_is_exynos5())
exynos5_set_mmc_clk(dev_index, div);
- else
+ else {
+ if (proid_is_exynos4412())
+ exynos4x12_set_mmc_clk(dev_index, div);
exynos4_set_mmc_clk(dev_index, div);
+ }
}
unsigned long get_lcd_clk(void)
*/
#include <common.h>
+#include <fdtdec.h>
#include <asm/arch/gpio.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/sromc.h>
}
}
+static int exynos4_mmc_config(int peripheral, int flags)
+{
+ struct exynos4_gpio_part2 *gpio2 =
+ (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
+ struct s5p_gpio_bank *bank, *bank_ext;
+ int i;
+
+ switch (peripheral) {
+ case PERIPH_ID_SDMMC0:
+ bank = &gpio2->k0;
+ bank_ext = &gpio2->k1;
+ break;
+ case PERIPH_ID_SDMMC2:
+ bank = &gpio2->k2;
+ bank_ext = &gpio2->k3;
+ break;
+ default:
+ return -1;
+ }
+ for (i = 0; i < 7; i++) {
+ if (i == 2)
+ continue;
+ s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
+ s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE);
+ s5p_gpio_set_drv(bank, i, GPIO_DRV_4X);
+ }
+ if (flags & PINMUX_FLAG_8BIT_MODE) {
+ for (i = 3; i < 7; i++) {
+ s5p_gpio_cfg_pin(bank_ext, i, GPIO_FUNC(0x3));
+ s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_NONE);
+ s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X);
+ }
+ }
+
+ return 0;
+}
+
static int exynos4_pinmux_config(int peripheral, int flags)
{
switch (peripheral) {
case PERIPH_ID_I2C7:
exynos4_i2c_config(peripheral, flags);
break;
+ case PERIPH_ID_SDMMC0:
+ case PERIPH_ID_SDMMC2:
+ return exynos4_mmc_config(peripheral, flags);
+ case PERIPH_ID_SDMMC1:
+ case PERIPH_ID_SDMMC3:
+ case PERIPH_ID_SDMMC4:
+ printf("SDMMC device %d not implemented\n", peripheral);
+ return -1;
default:
debug("%s: invalid peripheral %d", __func__, peripheral);
return -1;
return -1;
}
}
+
+#ifdef CONFIG_OF_CONTROL
+static int exynos5_pinmux_decode_periph_id(const void *blob, int node)
+{
+ int err;
+ u32 cell[3];
+
+ err = fdtdec_get_int_array(blob, node, "interrupts", cell,
+ ARRAY_SIZE(cell));
+ if (err)
+ return PERIPH_ID_NONE;
+
+ /* check for invalid peripheral id */
+ if ((PERIPH_ID_SDMMC4 > cell[1]) || (cell[1] < PERIPH_ID_UART0))
+ return cell[1];
+
+ debug(" invalid peripheral id\n");
+ return PERIPH_ID_NONE;
+}
+
+int pinmux_decode_periph_id(const void *blob, int node)
+{
+ if (cpu_is_exynos5())
+ return exynos5_pinmux_decode_periph_id(blob, node);
+ else
+ return PERIPH_ID_NONE;
+}
+#endif
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _image_copy_end_ofs
add r2, r0, r3 /* r2 <- source end address */
add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
- b clear_bss
+
+relocate_done:
+
+ bx lr
+
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_rel_dyn_end_ofs:
.word __rel_dyn_end - _start
_dynsym_start_ofs:
.word __dynsym_start - _start
+ENDPROC(relocate_code)
-clear_bss:
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
+#endif
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-jump_2_ram:
+ENTRY(c_runtime_cpu_setup)
/*
* If I-cache is enabled invalidate it
*/
mcr p15, 0, r0, c12, c0, 0 @Set VBAR
#endif /* !Tegra20 */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-ENDPROC(relocate_code)
-#endif
+ bx lr
+
+ENDPROC(c_runtime_cpu_setup)
/*************************************************************************
*
orr r0,r0,#0x13
msr cpsr,r0
-/* Set initial stackpointer in SDRAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
- bl coloured_LED_init
- bl red_led_on
-#endif
+relocate_done:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
+ bx lr
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ bx lr
+
/****************************************************************************/
/* */
/* Interrupt handling */
bl lock_cache_for_stack
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0, =0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
#ifndef CONFIG_SPL_BUILD
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
/* Disable the Dcache RAM lock for stack now */
#ifdef CONFIG_CPU_PXA25X
bl cpu_init_crit
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-#endif /* #ifndef CONFIG_SPL_BUILD */
+relocate_done:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
-#ifdef CONFIG_ONENAND_SPL
- ldr r0, _onenand_boot_ofs
- mov pc, r0
-
-_onenand_boot_ofs:
- .word onenand_boot
-#else
-jump_2_ram:
- ldr r0, _board_init_r_ofs
- ldr r1, _TEXT_BASE
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
-#endif
+ bx lr
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
.word __rel_dyn_end - _start
_dynsym_start_ofs:
.word __dynsym_start - _start
+
#endif
+
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ bx lr
+
/*
*************************************************************************
*
bl lowlevel_init
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-
- bl coloured_LED_init
- bl red_led_on
-#endif
+relocate_done:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
- mov pc, lr
-
-_board_init_r_ofs:
- .word board_init_r - _start
+ bx lr
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ bx lr
+
/*
*************************************************************************
*
bl cpu_init_crit
#endif
-/* Set stackpointer in internal RAM to call board_init_f */
-call_board_init_f:
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
- ldr r0,=0x00000000
- bl board_init_f
+ bl _main
/*------------------------------------------------------------------------------*/
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
- /* Set up the stack */
-stack_setup:
- mov sp, r4
-
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
- beq clear_bss /* skip relocation */
+ beq relocate_done /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
blo fixloop
#endif
-clear_bss:
-#ifndef CONFIG_SPL_BUILD
- ldr r0, _bss_start_ofs
- ldr r1, _bss_end_ofs
- mov r4, r6 /* reloc addr */
- add r0, r0, r4
- add r1, r1, r4
- mov r2, #0x00000000 /* clear */
-
-clbss_l:cmp r0, r1 /* clear loop... */
- bhs clbss_e /* if reached end of bss, exit */
- str r2, [r0]
- add r0, r0, #4
- b clbss_l
-clbss_e:
-#endif
+relocate_done:
-/*
- * We are done. Do not return, instead branch to second part of board
- * initialization, now running from RAM.
- */
- ldr r0, _board_init_r_ofs
- adr r1, _start
- add lr, r0, r1
- add lr, lr, r9
- /* setup parameters for board_init_r */
- mov r0, r5 /* gd_t */
- mov r1, r6 /* dest_addr */
- /* jump to it ... */
mov pc, lr
-_board_init_r_ofs:
- .word board_init_r - _start
-
_rel_dyn_start_ofs:
.word __rel_dyn_start - _start
_rel_dyn_end_ofs:
_dynsym_start_ofs:
.word __dynsym_start - _start
+ .globl c_runtime_cpu_setup
+c_runtime_cpu_setup:
+
+ mov pc, lr
+
/*
*************************************************************************
*
--- /dev/null
+/*
+ * SAMSUNG EXYNOS5250 SoC device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * SAMSUNG EXYNOS5250 SoC device nodes are listed in this file.
+ * EXYNOS5250 based board files can include this file and provide
+ * values for board specfic bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * EXYNOS5250 SoC. As device tree coverage for EXYNOS5250 increases,
+ * additional nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "skeleton.dtsi"
+
+/ {
+ compatible = "samsung,exynos5250";
+
+ sromc@12250000 {
+ compatible = "samsung,exynos-sromc";
+ reg = <0x12250000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c@12c60000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C60000 0x100>;
+ interrupts = <0 56 0>;
+ };
+
+ i2c@12c70000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C70000 0x100>;
+ interrupts = <0 57 0>;
+ };
+
+ i2c@12c80000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C80000 0x100>;
+ interrupts = <0 58 0>;
+ };
+
+ i2c@12c90000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12C90000 0x100>;
+ interrupts = <0 59 0>;
+ };
+
+ i2c@12ca0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12CA0000 0x100>;
+ interrupts = <0 60 0>;
+ };
+
+ i2c@12cb0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12CB0000 0x100>;
+ interrupts = <0 61 0>;
+ };
+
+ i2c@12cc0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12CC0000 0x100>;
+ interrupts = <0 62 0>;
+ };
+
+ i2c@12cd0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x12CD0000 0x100>;
+ interrupts = <0 63 0>;
+ };
+
+ sound@12d60000 {
+ compatible = "samsung,exynos-sound";
+ reg = <0x12d60000 0x20>;
+ };
+
+ spi@12d20000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,exynos-spi";
+ reg = <0x12d20000 0x30>;
+ interrupts = <0 68 0>;
+ };
+
+ spi@12d30000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,exynos-spi";
+ reg = <0x12d30000 0x30>;
+ interrupts = <0 69 0>;
+ };
+
+ spi@12d40000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,exynos-spi";
+ reg = <0x12d40000 0x30>;
+ clock-frequency = <50000000>;
+ interrupts = <0 70 0>;
+ };
+
+ spi@131a0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,exynos-spi";
+ reg = <0x131a0000 0x30>;
+ interrupts = <0 129 0>;
+ };
+
+ spi@131b0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,exynos-spi";
+ reg = <0x131b0000 0x30>;
+ interrupts = <0 130 0>;
+ };
+
+ ehci@12110000 {
+ compatible = "samsung,exynos-ehci";
+ reg = <0x12110000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ phy {
+ compatible = "samsung,exynos-usb-phy";
+ reg = <0x12130000 0x100>;
+ };
+ };
+
+};
#define ATMEL_PIO_PORTS 4
#define CPU_HAS_PIO3
#define PIO_SCDR_DIV (0x3fff << 0) /* Slow Clock Divider Mask */
+#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
+#define ATMEL_ID_UHP ATMEL_ID_UHPHS
/*
* at91sam9x5 specific prototypes
unsigned long get_i2c_clk(void);
unsigned long get_pwm_clk(void);
unsigned long get_uart_clk(int dev_index);
+unsigned long get_mmc_clk(int dev_index);
void set_mmc_clk(int dev_index, unsigned int div);
unsigned long get_lcd_clk(void);
void set_lcd_clk(void);
unsigned int div_iem_l1;
};
+struct exynos4x12_clock {
+ unsigned char res1[0x4200];
+ unsigned int src_leftbus;
+ unsigned char res2[0x1fc];
+ unsigned int mux_stat_leftbus;
+ unsigned char res3[0xfc];
+ unsigned int div_leftbus;
+ unsigned char res4[0xfc];
+ unsigned int div_stat_leftbus;
+ unsigned char res5[0x1fc];
+ unsigned int gate_ip_leftbus;
+ unsigned char res6[0x12c];
+ unsigned int gate_ip_image;
+ unsigned char res7[0xcc];
+ unsigned int clkout_leftbus;
+ unsigned int clkout_leftbus_div_stat;
+ unsigned char res8[0x37f8];
+ unsigned int src_rightbus;
+ unsigned char res9[0x1fc];
+ unsigned int mux_stat_rightbus;
+ unsigned char res10[0xfc];
+ unsigned int div_rightbus;
+ unsigned char res11[0xfc];
+ unsigned int div_stat_rightbus;
+ unsigned char res12[0x1fc];
+ unsigned int gate_ip_rightbus;
+ unsigned char res13[0x15c];
+ unsigned int gate_ip_perir;
+ unsigned char res14[0x9c];
+ unsigned int clkout_rightbus;
+ unsigned int clkout_rightbus_div_stat;
+ unsigned char res15[0x3608];
+ unsigned int epll_lock;
+ unsigned char res16[0xc];
+ unsigned int vpll_lock;
+ unsigned char res17[0xec];
+ unsigned int epll_con0;
+ unsigned int epll_con1;
+ unsigned int epll_con2;
+ unsigned char res18[0x4];
+ unsigned int vpll_con0;
+ unsigned int vpll_con1;
+ unsigned int vpll_con2;
+ unsigned char res19[0xe4];
+ unsigned int src_top0;
+ unsigned int src_top1;
+ unsigned char res20[0x8];
+ unsigned int src_cam;
+ unsigned int src_tv;
+ unsigned int src_mfc;
+ unsigned int src_g3d;
+ unsigned char res21[0x4];
+ unsigned int src_lcd;
+ unsigned int src_isp;
+ unsigned int src_maudio;
+ unsigned int src_fsys;
+ unsigned char res22[0xc];
+ unsigned int src_peril0;
+ unsigned int src_peril1;
+ unsigned int src_cam1;
+ unsigned char res23[0xb4];
+ unsigned int src_mask_top;
+ unsigned char res24[0xc];
+ unsigned int src_mask_cam;
+ unsigned int src_mask_tv;
+ unsigned char res25[0xc];
+ unsigned int src_mask_lcd;
+ unsigned int src_mask_isp;
+ unsigned int src_mask_maudio;
+ unsigned int src_mask_fsys;
+ unsigned char res26[0xc];
+ unsigned int src_mask_peril0;
+ unsigned int src_mask_peril1;
+ unsigned char res27[0xb8];
+ unsigned int mux_stat_top0;
+ unsigned int mux_stat_top1;
+ unsigned char res28[0x10];
+ unsigned int mux_stat_mfc;
+ unsigned int mux_stat_g3d;
+ unsigned char res29[0x28];
+ unsigned int mux_stat_cam1;
+ unsigned char res30[0xb4];
+ unsigned int div_top;
+ unsigned char res31[0xc];
+ unsigned int div_cam;
+ unsigned int div_tv;
+ unsigned int div_mfc;
+ unsigned int div_g3d;
+ unsigned char res32[0x4];
+ unsigned int div_lcd;
+ unsigned int div_isp;
+ unsigned int div_maudio;
+ unsigned int div_fsys0;
+ unsigned int div_fsys1;
+ unsigned int div_fsys2;
+ unsigned int div_fsys3;
+ unsigned int div_peril0;
+ unsigned int div_peril1;
+ unsigned int div_peril2;
+ unsigned int div_peril3;
+ unsigned int div_peril4;
+ unsigned int div_peril5;
+ unsigned int div_cam1;
+ unsigned char res33[0x14];
+ unsigned int div2_ratio;
+ unsigned char res34[0x8c];
+ unsigned int div_stat_top;
+ unsigned char res35[0xc];
+ unsigned int div_stat_cam;
+ unsigned int div_stat_tv;
+ unsigned int div_stat_mfc;
+ unsigned int div_stat_g3d;
+ unsigned char res36[0x4];
+ unsigned int div_stat_lcd;
+ unsigned int div_stat_isp;
+ unsigned int div_stat_maudio;
+ unsigned int div_stat_fsys0;
+ unsigned int div_stat_fsys1;
+ unsigned int div_stat_fsys2;
+ unsigned int div_stat_fsys3;
+ unsigned int div_stat_peril0;
+ unsigned int div_stat_peril1;
+ unsigned int div_stat_peril2;
+ unsigned int div_stat_peril3;
+ unsigned int div_stat_peril4;
+ unsigned int div_stat_peril5;
+ unsigned int div_stat_cam1;
+ unsigned char res37[0x14];
+ unsigned int div2_stat;
+ unsigned char res38[0x29c];
+ unsigned int gate_ip_cam;
+ unsigned int gate_ip_tv;
+ unsigned int gate_ip_mfc;
+ unsigned int gate_ip_g3d;
+ unsigned char res39[0x4];
+ unsigned int gate_ip_lcd;
+ unsigned int gate_ip_isp;
+ unsigned char res40[0x4];
+ unsigned int gate_ip_fsys;
+ unsigned char res41[0x8];
+ unsigned int gate_ip_gps;
+ unsigned int gate_ip_peril;
+ unsigned char res42[0xc];
+ unsigned char res43[0x4];
+ unsigned char res44[0xc];
+ unsigned int gate_block;
+ unsigned char res45[0x8c];
+ unsigned int clkout_cmu_top;
+ unsigned int clkout_cmu_top_div_stat;
+ unsigned char res46[0x3600];
+ unsigned int mpll_lock;
+ unsigned char res47[0xfc];
+ unsigned int mpll_con0;
+ unsigned int mpll_con1;
+ unsigned char res48[0xf0];
+ unsigned int src_dmc;
+ unsigned char res49[0xfc];
+ unsigned int src_mask_dmc;
+ unsigned char res50[0xfc];
+ unsigned int mux_stat_dmc;
+ unsigned char res51[0xfc];
+ unsigned int div_dmc0;
+ unsigned int div_dmc1;
+ unsigned char res52[0xf8];
+ unsigned int div_stat_dmc0;
+ unsigned int div_stat_dmc1;
+ unsigned char res53[0xf8];
+ unsigned int gate_bus_dmc0;
+ unsigned int gate_bus_dmc1;
+ unsigned char res54[0x1f8];
+ unsigned int gate_ip_dmc0;
+ unsigned int gate_ip_dmc1;
+ unsigned char res55[0xf8];
+ unsigned int clkout_cmu_dmc;
+ unsigned int clkout_cmu_dmc_div_stat;
+ unsigned char res56[0x5f8];
+ unsigned int dcgidx_map0;
+ unsigned int dcgidx_map1;
+ unsigned int dcgidx_map2;
+ unsigned char res57[0x14];
+ unsigned int dcgperf_map0;
+ unsigned int dcgperf_map1;
+ unsigned char res58[0x18];
+ unsigned int dvcidx_map;
+ unsigned char res59[0x1c];
+ unsigned int freq_cpu;
+ unsigned int freq_dpm;
+ unsigned char res60[0x18];
+ unsigned int dvsemclk_en;
+ unsigned int maxperf;
+ unsigned char res61[0x8];
+ unsigned int dmc_freq_ctrl;
+ unsigned int dmc_pause_ctrl;
+ unsigned int dddrphy_lock_ctrl;
+ unsigned int c2c_state;
+ unsigned char res62[0x2f60];
+ unsigned int apll_lock;
+ unsigned char res63[0x8];
+ unsigned char res64[0xf4];
+ unsigned int apll_con0;
+ unsigned int apll_con1;
+ unsigned char res65[0xf8];
+ unsigned int src_cpu;
+ unsigned char res66[0x1fc];
+ unsigned int mux_stat_cpu;
+ unsigned char res67[0xfc];
+ unsigned int div_cpu0;
+ unsigned int div_cpu1;
+ unsigned char res68[0xf8];
+ unsigned int div_stat_cpu0;
+ unsigned int div_stat_cpu1;
+ unsigned char res69[0x2f8];
+ unsigned int clk_gate_ip_cpu;
+ unsigned char res70[0xfc];
+ unsigned int clkout_cmu_cpu;
+ unsigned int clkout_cmu_cpu_div_stat;
+ unsigned char res71[0x5f8];
+ unsigned int armclk_stopctrl;
+ unsigned int atclk_stopctrl;
+ unsigned char res72[0x10];
+ unsigned char res73[0x8];
+ unsigned int pwr_ctrl;
+ unsigned int pwr_ctrl2;
+ unsigned char res74[0xd8];
+ unsigned int apll_con0_l8;
+ unsigned int apll_con0_l7;
+ unsigned int apll_con0_l6;
+ unsigned int apll_con0_l5;
+ unsigned int apll_con0_l4;
+ unsigned int apll_con0_l3;
+ unsigned int apll_con0_l2;
+ unsigned int apll_con0_l1;
+ unsigned int iem_control;
+ unsigned char res75[0xdc];
+ unsigned int apll_con1_l8;
+ unsigned int apll_con1_l7;
+ unsigned int apll_con1_l6;
+ unsigned int apll_con1_l5;
+ unsigned int apll_con1_l4;
+ unsigned int apll_con1_l3;
+ unsigned int apll_con1_l2;
+ unsigned int apll_con1_l1;
+ unsigned char res76[0xe0];
+ unsigned int div_iem_l8;
+ unsigned int div_iem_l7;
+ unsigned int div_iem_l6;
+ unsigned int div_iem_l5;
+ unsigned int div_iem_l4;
+ unsigned int div_iem_l3;
+ unsigned int div_iem_l2;
+ unsigned int div_iem_l1;
+ unsigned char res77[0xe0];
+ unsigned int l2_status;
+ unsigned char res78[0xc];
+ unsigned int cpu_status;
+ unsigned char res79[0xc];
+ unsigned int ptm_status;
+ unsigned char res80[0x2edc];
+ unsigned int div_isp0;
+ unsigned int div_isp1;
+ unsigned char res81[0xf8];
+ unsigned int div_stat_isp0;
+ unsigned int div_stat_isp1;
+ unsigned char res82[0x3f8];
+ unsigned int gate_ip_isp0;
+ unsigned int gate_ip_isp1;
+ unsigned char res83[0x1f8];
+ unsigned int clkout_cmu_isp;
+ unsigned int clkout_cmu_ispd_div_stat;
+ unsigned char res84[0xf8];
+ unsigned int cmu_isp_spar0;
+ unsigned int cmu_isp_spar1;
+ unsigned int cmu_isp_spar2;
+ unsigned int cmu_isp_spar3;
+};
+
struct exynos5_clock {
unsigned int apll_lock;
unsigned char res1[0xfc];
#define EXYNOS_CPU_NAME "Exynos"
#define EXYNOS4_ADDR_BASE 0x10000000
-/* EXYNOS4 */
+/* EXYNOS4 Common*/
#define EXYNOS4_I2C_SPACING 0x10000
#define EXYNOS4_GPIO_PART3_BASE 0x03860000
#define EXYNOS4_DP_BASE DEVICE_NOT_AVAILABLE
#define EXYNOS4_SPI_ISP_BASE DEVICE_NOT_AVAILABLE
-/* EXYNOS5 */
+/* EXYNOS4X12 */
+#define EXYNOS4X12_GPIO_PART3_BASE 0x03860000
+#define EXYNOS4X12_PRO_ID 0x10000000
+#define EXYNOS4X12_SYSREG_BASE 0x10010000
+#define EXYNOS4X12_POWER_BASE 0x10020000
+#define EXYNOS4X12_SWRESET 0x10020400
+#define EXYNOS4X12_USBPHY_CONTROL 0x10020704
+#define EXYNOS4X12_CLOCK_BASE 0x10030000
+#define EXYNOS4X12_SYSTIMER_BASE 0x10050000
+#define EXYNOS4X12_WATCHDOG_BASE 0x10060000
+#define EXYNOS4X12_DMC0_BASE 0x10600000
+#define EXYNOS4X12_DMC1_BASE 0x10610000
+#define EXYNOS4X12_GPIO_PART4_BASE 0x106E0000
+#define EXYNOS4X12_GPIO_PART2_BASE 0x11000000
+#define EXYNOS4X12_GPIO_PART1_BASE 0x11400000
+#define EXYNOS4X12_FIMD_BASE 0x11C00000
+#define EXYNOS4X12_MIPI_DSIM_BASE 0x11C80000
+#define EXYNOS4X12_USBOTG_BASE 0x12480000
+#define EXYNOS4X12_MMC_BASE 0x12510000
+#define EXYNOS4X12_SROMC_BASE 0x12570000
+#define EXYNOS4X12_USB_HOST_EHCI_BASE 0x12580000
+#define EXYNOS4X12_USBPHY_BASE 0x125B0000
+#define EXYNOS4X12_UART_BASE 0x13800000
+#define EXYNOS4X12_I2C_BASE 0x13860000
+#define EXYNOS4X12_PWMTIMER_BASE 0x139D0000
+
+#define EXYNOS4X12_ADC_BASE DEVICE_NOT_AVAILABLE
+#define EXYNOS4X12_DP_BASE DEVICE_NOT_AVAILABLE
+#define EXYNOS4X12_MODEM_BASE DEVICE_NOT_AVAILABLE
+#define EXYNOS4X12_I2S_BASE DEVICE_NOT_AVAILABLE
+#define EXYNOS4X12_SPI_BASE DEVICE_NOT_AVAILABLE
+#define EXYNOS4X12_SPI_ISP_BASE DEVICE_NOT_AVAILABLE
+
+/* EXYNOS5 Common*/
#define EXYNOS5_I2C_SPACING 0x10000
#define EXYNOS5_GPIO_PART4_BASE 0x03860000
}
IS_EXYNOS_TYPE(exynos4210, 0x4210)
+IS_EXYNOS_TYPE(exynos4412, 0x4412)
IS_EXYNOS_TYPE(exynos5250, 0x5250)
#define SAMSUNG_BASE(device, base) \
static inline unsigned int samsung_get_base_##device(void) \
{ \
- if (cpu_is_exynos4()) \
+ if (cpu_is_exynos4()) { \
+ if (proid_is_exynos4412()) \
+ return EXYNOS4X12_##base; \
return EXYNOS4_##base; \
- else if (cpu_is_exynos5()) \
+ } else if (cpu_is_exynos5()) { \
return EXYNOS5_##base; \
- else \
- return 0; \
+ } \
+ return 0; \
}
SAMSUNG_BASE(adc, ADC_BASE)
}
#endif
+void exynos_set_dp_platform_data(struct exynos_dp_platform_data *pd);
+
#endif /* _DP_INFO_H */
struct s5p_gpio_bank z;
};
+struct exynos4x12_gpio_part1 {
+ struct s5p_gpio_bank a0;
+ struct s5p_gpio_bank a1;
+ struct s5p_gpio_bank b;
+ struct s5p_gpio_bank c0;
+ struct s5p_gpio_bank c1;
+ struct s5p_gpio_bank d0;
+ struct s5p_gpio_bank d1;
+ struct s5p_gpio_bank res1[0x5];
+ struct s5p_gpio_bank f0;
+ struct s5p_gpio_bank f1;
+ struct s5p_gpio_bank f2;
+ struct s5p_gpio_bank f3;
+ struct s5p_gpio_bank res2[0x2];
+ struct s5p_gpio_bank j0;
+ struct s5p_gpio_bank j1;
+};
+
+struct exynos4x12_gpio_part2 {
+ struct s5p_gpio_bank res1[0x2];
+ struct s5p_gpio_bank k0;
+ struct s5p_gpio_bank k1;
+ struct s5p_gpio_bank k2;
+ struct s5p_gpio_bank k3;
+ struct s5p_gpio_bank l0;
+ struct s5p_gpio_bank l1;
+ struct s5p_gpio_bank l2;
+ struct s5p_gpio_bank y0;
+ struct s5p_gpio_bank y1;
+ struct s5p_gpio_bank y2;
+ struct s5p_gpio_bank y3;
+ struct s5p_gpio_bank y4;
+ struct s5p_gpio_bank y5;
+ struct s5p_gpio_bank y6;
+ struct s5p_gpio_bank res2[0x3];
+ struct s5p_gpio_bank m0;
+ struct s5p_gpio_bank m1;
+ struct s5p_gpio_bank m2;
+ struct s5p_gpio_bank m3;
+ struct s5p_gpio_bank m4;
+ struct s5p_gpio_bank res3[0x48];
+ struct s5p_gpio_bank x0;
+ struct s5p_gpio_bank x1;
+ struct s5p_gpio_bank x2;
+ struct s5p_gpio_bank x3;
+};
+
+struct exynos4x12_gpio_part3 {
+ struct s5p_gpio_bank z;
+};
+
+struct exynos4x12_gpio_part4 {
+ struct s5p_gpio_bank v0;
+ struct s5p_gpio_bank v1;
+ struct s5p_gpio_bank res1[0x1];
+ struct s5p_gpio_bank v2;
+ struct s5p_gpio_bank v3;
+ struct s5p_gpio_bank res2[0x1];
+ struct s5p_gpio_bank v4;
+};
+
struct exynos5_gpio_part1 {
struct s5p_gpio_bank a0;
struct s5p_gpio_bank a1;
- EXYNOS4_GPIO_PART2_BASE) / sizeof(struct s5p_gpio_bank)) \
* GPIO_PER_BANK) + pin) + EXYNOS4_GPIO_PART1_MAX)
+#define exynos4x12_gpio_part1_get_nr(bank, pin) \
+ ((((((unsigned int) &(((struct exynos4x12_gpio_part1 *) \
+ EXYNOS4X12_GPIO_PART1_BASE)->bank)) \
+ - EXYNOS4X12_GPIO_PART1_BASE) / sizeof(struct s5p_gpio_bank)) \
+ * GPIO_PER_BANK) + pin)
+
+#define EXYNOS4X12_GPIO_PART1_MAX ((sizeof(struct exynos4x12_gpio_part1) \
+ / sizeof(struct s5p_gpio_bank)) * GPIO_PER_BANK)
+
+#define exynos4x12_gpio_part2_get_nr(bank, pin) \
+ (((((((unsigned int) &(((struct exynos4x12_gpio_part2 *) \
+ EXYNOS4X12_GPIO_PART2_BASE)->bank)) \
+ - EXYNOS4X12_GPIO_PART2_BASE) / sizeof(struct s5p_gpio_bank)) \
+ * GPIO_PER_BANK) + pin) + EXYNOS4X12_GPIO_PART1_MAX)
+
+#define EXYNOS4X12_GPIO_PART2_MAX ((sizeof(struct exynos4x12_gpio_part2) \
+ / sizeof(struct s5p_gpio_bank)) * GPIO_PER_BANK)
+
+#define exynos4x12_gpio_part3_get_nr(bank, pin) \
+ (((((((unsigned int) &(((struct exynos4x12_gpio_part3 *) \
+ EXYNOS4X12_GPIO_PART3_BASE)->bank)) \
+ - EXYNOS4X12_GPIO_PART3_BASE) / sizeof(struct s5p_gpio_bank)) \
+ * GPIO_PER_BANK) + pin) + EXYNOS4X12_GPIO_PART2_MAX)
+
#define exynos5_gpio_part1_get_nr(bank, pin) \
((((((unsigned int) &(((struct exynos5_gpio_part1 *) \
EXYNOS5_GPIO_PART1_BASE)->bank)) \
void (*mipi_display_on)(struct mipi_dsim_device *dsim_dev);
};
+#ifdef CONFIG_EXYNOS_MIPI_DSIM
int exynos_mipi_dsi_init(void);
+#else
+static inline int exynos_mipi_dsi_init(void)
+{
+ return 0;
+}
+#endif
/*
* register mipi_dsim_lcd_driver object defined by lcd panel driver
#define __ASM_ARM_ARCH_PERIPH_H
/*
- * Peripherals requiring clock/pinmux configuration. List will
+ * Peripherals required for pinmux configuration. List will
* grow with support for more devices getting added.
+ * Numbering based on interrupt table.
*
*/
enum periph_id {
- PERIPH_ID_I2C0,
+ PERIPH_ID_UART0 = 51,
+ PERIPH_ID_UART1,
+ PERIPH_ID_UART2,
+ PERIPH_ID_UART3,
+ PERIPH_ID_I2C0 = 56,
PERIPH_ID_I2C1,
PERIPH_ID_I2C2,
PERIPH_ID_I2C3,
PERIPH_ID_I2C5,
PERIPH_ID_I2C6,
PERIPH_ID_I2C7,
- PERIPH_ID_I2S1,
- PERIPH_ID_SDMMC0,
+ PERIPH_ID_SPI0 = 68,
+ PERIPH_ID_SPI1,
+ PERIPH_ID_SPI2,
+ PERIPH_ID_SDMMC0 = 75,
PERIPH_ID_SDMMC1,
PERIPH_ID_SDMMC2,
PERIPH_ID_SDMMC3,
- PERIPH_ID_SDMMC4,
- PERIPH_ID_SROMC,
- PERIPH_ID_SPI0,
- PERIPH_ID_SPI1,
- PERIPH_ID_SPI2,
+ PERIPH_ID_I2S1 = 99,
+
+ /* Since following peripherals do
+ * not have shared peripheral interrupts (SPIs)
+ * they are numbered arbitiraly after the maximum
+ * SPIs Exynos has (128)
+ */
+ PERIPH_ID_SROMC = 128,
PERIPH_ID_SPI3,
PERIPH_ID_SPI4,
- PERIPH_ID_UART0,
- PERIPH_ID_UART1,
- PERIPH_ID_UART2,
- PERIPH_ID_UART3,
+ PERIPH_ID_SDMMC4,
PERIPH_ID_COUNT,
PERIPH_ID_NONE = -1,
*/
int exynos_pinmux_config(int peripheral, int flags);
+/**
+ * Decode the peripheral id using the interrpt numbers.
+ *
+ * @param blob Device tree blob
+ * @param node FDT I2C node to find
+ * @return peripheral id if ok, PERIPH_ID_NONE on error
+ */
+int pinmux_decode_periph_id(const void *blob, int node);
#endif
/* Configure the Band Width and Bank Control Regs for required SROMC Bank */
void s5p_config_sromc(u32 srom_bank, u32 srom_bw_conf, u32 srom_bc_conf);
+enum {
+ FDT_SROM_PMC,
+ FDT_SROM_TACP,
+ FDT_SROM_TAH,
+ FDT_SROM_TCOH,
+ FDT_SROM_TACC,
+ FDT_SROM_TCOS,
+ FDT_SROM_TACS,
+
+ FDT_SROM_TIMING_COUNT,
+};
+
+struct fdt_sromc {
+ u8 bank; /* srom bank number */
+ u8 width; /* bus width in bytes */
+ unsigned int timing[FDT_SROM_TIMING_COUNT]; /* timing parameters */
+};
+
#endif /* __ASM_ARCH_SROMC_H_ */
| (attr << 8) | (kw_winctrl_calcsize(size) << 16))
#define KWGBE_PORT_SERIAL_CONTROL1_REG(_x) \
- ((_x ? KW_EGIGA0_BASE : KW_EGIGA1_BASE) + 0x44c)
+ ((_x ? KW_EGIGA1_BASE : KW_EGIGA0_BASE) + 0x44c)
#define KW_REG_PCIE_DEVID (KW_REG_PCIE_BASE + 0x00)
#define KW_REG_PCIE_REVID (KW_REG_PCIE_BASE + 0x08)
#define MPP_MAX 49
-void kirkwood_mpp_conf(u32 *mpp_list, u32 *mpp_save);
+void kirkwood_mpp_conf(const u32 *mpp_list, u32 *mpp_save);
#endif
unsigned long reloc_off;
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
unsigned long tlb_addr;
+ unsigned long tlb_size;
#endif
const void *fdt_blob; /* Our device tree, NULL if none */
void **jt; /* jump table */
GLCOBJS += div0.o
+SOBJS-y += crt0.o
+
ifndef CONFIG_SPL_BUILD
COBJS-y += board.o
COBJS-y += bootm.o
COBJS-$(CONFIG_SYS_L2_PL310) += cache-pl310.o
-COBJS-y += interrupts.o
-COBJS-y += reset.o
SOBJS-$(CONFIG_USE_ARCH_MEMSET) += memset.o
SOBJS-$(CONFIG_USE_ARCH_MEMCPY) += memcpy.o
else
COBJS-$(CONFIG_SPL_FRAMEWORK) += spl.o
endif
+COBJS-y += interrupts.o
+COBJS-y += reset.o
+
COBJS-y += cache.o
COBJS-y += cache-cp15.o
#include <common.h>
#include <command.h>
+#include <environment.h>
#include <malloc.h>
#include <stdio_dev.h>
#include <version.h>
int power_init_board(void)
__attribute__((weak, alias("__power_init_board")));
+ /* Record the board_init_f() bootstage (after arch_cpu_init()) */
+static int mark_bootstage(void)
+{
+ bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_F, "board_init_f");
+
+ return 0;
+}
+
init_fnc_t *init_sequence[] = {
arch_cpu_init, /* basic arch cpu dependent setup */
-
-#if defined(CONFIG_BOARD_EARLY_INIT_F)
- board_early_init_f,
-#endif
+ mark_bootstage,
#ifdef CONFIG_OF_CONTROL
fdtdec_check_fdt,
#endif
+#if defined(CONFIG_BOARD_EARLY_INIT_F)
+ board_early_init_f,
+#endif
timer_init, /* initialize timer */
#ifdef CONFIG_BOARD_POSTCLK_INIT
board_postclk_init,
void *new_fdt = NULL;
size_t fdt_size = 0;
- bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_F, "board_init_f");
-
- /* Pointer is writable since we allocated a register for it */
- gd = (gd_t *) ((CONFIG_SYS_INIT_SP_ADDR) & ~0x07);
- /* compiler optimization barrier needed for GCC >= 3.4 */
- __asm__ __volatile__("": : :"memory");
-
memset((void *)gd, 0, sizeof(gd_t));
gd->mon_len = _bss_end_ofs;
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
/* reserve TLB table */
- addr -= (4096 * 4);
+ gd->tlb_size = 4096 * 4;
+ addr -= gd->tlb_size;
/* round down to next 64 kB limit */
addr &= ~(0x10000 - 1);
gd->tlb_addr = addr;
- debug("TLB table at: %08lx\n", addr);
+ debug("TLB table from %08lx to %08lx\n", addr, addr + gd->tlb_size);
#endif
/* round down to next 4 kB limit */
gd->fdt_blob = new_fdt;
}
memcpy(id, (void *)gd, sizeof(gd_t));
-
- relocate_code(addr_sp, id, addr);
-
- /* NOTREACHED - relocate_code() does not return */
}
#if !defined(CONFIG_SYS_NO_FLASH)
#endif
/*
- ************************************************************************
+ * Tell if it's OK to load the environment early in boot.
+ *
+ * If CONFIG_OF_CONFIG is defined, we'll check with the FDT to see
+ * if this is OK (defaulting to saying it's not OK).
+ *
+ * NOTE: Loading the environment early can be a bad idea if security is
+ * important, since no verification is done on the environment.
+ *
+ * @return 0 if environment should not be loaded, !=0 if it is ok to load
+ */
+static int should_load_env(void)
+{
+#ifdef CONFIG_OF_CONTROL
+ return fdtdec_get_config_int(gd->fdt_blob, "load-environment", 0);
+#elif defined CONFIG_DELAY_ENVIRONMENT
+ return 0;
+#else
+ return 1;
+#endif
+}
+
+#if defined(CONFIG_DISPLAY_BOARDINFO_LATE) && defined(CONFIG_OF_CONTROL)
+static void display_fdt_model(const void *blob)
+{
+ const char *model;
+
+ model = (char *)fdt_getprop(blob, 0, "model", NULL);
+ printf("Model: %s\n", model ? model : "<unknown>");
+}
+#endif
+
+/************************************************************************
*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
ulong flash_size;
#endif
- gd = id;
-
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
#endif
#ifdef CONFIG_GENERIC_MMC
- puts("MMC: ");
- mmc_initialize(gd->bd);
+ puts("MMC: ");
+ mmc_initialize(gd->bd);
#endif
#ifdef CONFIG_HAS_DATAFLASH
#endif
/* initialize environment */
- env_relocate();
+ if (should_load_env())
+ env_relocate();
+ else
+ set_default_env(NULL);
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
console_init_r(); /* fully init console as a device */
+#ifdef CONFIG_DISPLAY_BOARDINFO_LATE
+# ifdef CONFIG_OF_CONTROL
+ /* Put this here so it appears on the LCD, now it is ready */
+ display_fdt_model(gd->fdt_blob);
+# else
+ checkboard();
+# endif
+#endif
+
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
return;
/* if disabling data cache, disable mmu too */
cache_bit |= CR_M;
- flush_dcache_all();
}
+ reg = get_cr();
+ cp_delay();
+ if (cache_bit == (CR_C | CR_M))
+ flush_dcache_all();
set_cr(reg & ~cache_bit);
}
#endif
--- /dev/null
+/*
+ * crt0 - C-runtime startup Code for ARM U-Boot
+ *
+ * Copyright (c) 2012 Albert ARIBAUD <albert.u.boot@aribaud.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm-offsets.h>
+
+/*
+ * This file handles the target-independent stages of the U-Boot
+ * start-up where a C runtime environment is needed. Its entry point
+ * is _main and is branched into from the target's start.S file.
+ *
+ * _main execution sequence is:
+ *
+ * 1. Set up initial environment for calling board_init_f().
+ * This environment only provides a stack and a place to store
+ * the GD ('global data') structure, both located in some readily
+ * available RAM (SRAM, locked cache...). In this context, VARIABLE
+ * global data, initialized or not (BSS), are UNAVAILABLE; only
+ * CONSTANT initialized data are available.
+ *
+ * 2. Call board_init_f(). This function prepares the hardware for
+ * execution from system RAM (DRAM, DDR...) As system RAM may not
+ * be available yet, , board_init_f() must use the current GD to
+ * store any data which must be passed on to later stages. These
+ * data include the relocation destination, the future stack, and
+ * the future GD location.
+ *
+ * (the following applies only to non-SPL builds)
+ *
+ * 3. Set up intermediate environment where the stack and GD are the
+ * ones allocated by board_init_f() in system RAM, but BSS and
+ * initialized non-const data are still not available.
+ *
+ * 4. Call relocate_code(). This function relocates U-Boot from its
+ * current location into the relocation destination computed by
+ * board_init_f().
+ *
+ * 5. Set up final environment for calling board_init_r(). This
+ * environment has BSS (initialized to 0), initialized non-const
+ * data (initialized to their intended value), and stack in system
+ * RAM. GD has retained values set by board_init_f(). Some CPUs
+ * have some work left to do at this point regarding memory, so
+ * call c_runtime_cpu_setup.
+ *
+ * 6. Branch to either nand_boot() or board_init_r().
+ */
+
+/*
+ * declare nand_boot() or board_init_r() to jump to at end of crt0
+ */
+
+#if defined(CONFIG_NAND_SPL)
+
+.globl nand_boot
+
+#elif ! defined(CONFIG_SPL_BUILD)
+
+.globl board_init_r
+
+#endif
+
+/*
+ * start and end of BSS
+ */
+
+.globl __bss_start
+.globl __bss_end__
+
+/*
+ * entry point of crt0 sequence
+ */
+
+.global _main
+
+_main:
+
+/*
+ * Set up initial C runtime environment and call board_init_f(0).
+ */
+
+#if defined(CONFIG_NAND_SPL)
+ /* deprecated, use instead CONFIG_SPL_BUILD */
+ ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
+#elif defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK)
+ ldr sp, =(CONFIG_SPL_STACK)
+#else
+ ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
+#endif
+ bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
+ sub sp, #GD_SIZE /* allocate one GD above SP */
+ bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
+ mov r8, sp /* GD is above SP */
+ mov r0, #0
+ bl board_init_f
+
+#if ! defined(CONFIG_SPL_BUILD)
+
+/*
+ * Set up intermediate environment (new sp and gd) and call
+ * relocate_code(addr_sp, gd, addr_moni). Trick here is that
+ * we'll return 'here' but relocated.
+ */
+
+ ldr sp, [r8, #GD_START_ADDR_SP] /* r8 = gd->start_addr_sp */
+ bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
+ ldr r8, [r8, #GD_BD] /* r8 = gd->bd */
+ sub r8, r8, #GD_SIZE /* new GD is below bd */
+
+ adr lr, here
+ ldr r0, [r8, #GD_RELOC_OFF] /* lr = gd->start_addr_sp */
+ add lr, lr, r0
+ ldr r0, [r8, #GD_START_ADDR_SP] /* r0 = gd->start_addr_sp */
+ mov r1, r8 /* r1 = gd */
+ ldr r2, [r8, #GD_RELOCADDR] /* r2 = gd->relocaddr */
+ b relocate_code
+here:
+
+/* Set up final (full) environment */
+
+ bl c_runtime_cpu_setup /* we still call old routine here */
+
+ ldr r0, =__bss_start /* this is auto-relocated! */
+ ldr r1, =__bss_end__ /* this is auto-relocated! */
+
+ mov r2, #0x00000000 /* prepare zero to clear BSS */
+
+clbss_l:cmp r0, r1 /* while not at end of BSS */
+ strlo r2, [r0] /* clear 32-bit BSS word */
+ addlo r0, r0, #4 /* move to next */
+ blo clbss_l
+
+ bl coloured_LED_init
+ bl red_led_on
+
+#if defined(CONFIG_NAND_SPL)
+
+ /* call _nand_boot() */
+ ldr pc, =nand_boot
+
+#else
+
+ /* call board_init_r(gd_t *id, ulong dest_addr) */
+ mov r0, r8 /* gd_t */
+ ldr r1, [r8, #GD_RELOCADDR] /* dest_addr */
+ /* call board_init_r */
+ ldr pc, =board_init_r /* this is auto-relocated! */
+
+#endif
+
+ /* we should not return here. */
+
+#endif
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
- serial_initialize();
-
debug ("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
WATCHDOG_RESET ();
gd->reloc_off = dest_addr - CONFIG_SYS_MONITOR_BASE;
+ serial_initialize();
+
monitor_flash_len = (ulong)&__init_end - dest_addr;
#if defined(CONFIG_NEEDS_MANUAL_RELOC)
# include <asm/cpu_sh7724.h>
#elif defined (CONFIG_CPU_SH7734)
# include <asm/cpu_sh7734.h>
+#elif defined (CONFIG_CPU_SH7752)
+# include <asm/cpu_sh7752.h>
#elif defined (CONFIG_CPU_SH7757)
# include <asm/cpu_sh7757.h>
#elif defined (CONFIG_CPU_SH7763)
--- /dev/null
+/*
+ * Copyright (C) 2012 Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef _ASM_CPU_SH7752_H_
+#define _ASM_CPU_SH7752_H_
+
+#define CCR 0xFF00001C
+#define WTCNT 0xFFCC0000
+#define CCR_CACHE_INIT 0x0000090b
+#define CACHE_OC_NUM_WAYS 1
+
+#ifndef __ASSEMBLY__ /* put C only stuff in this section */
+/* MMU */
+struct mmu_regs {
+ unsigned int reserved[4];
+ unsigned int mmucr;
+};
+#define MMU_BASE ((struct mmu_regs *)0xff000000)
+
+/* Watchdog */
+#define WTCSR0 0xffcc0002
+#define WRSTCSR_R 0xffcc0003
+#define WRSTCSR_W 0xffcc0002
+#define WTCSR_PREFIX 0xa500
+#define WRSTCSR_PREFIX 0x6900
+#define WRSTCSR_WOVF_PREFIX 0x9600
+
+/* SCIF */
+#define SCIF0_BASE 0xfe4b0000 /* The real name is SCIF2 */
+#define SCIF1_BASE 0xfe4c0000 /* The real name is SCIF3 */
+#define SCIF2_BASE 0xfe4d0000 /* The real name is SCIF4 */
+
+/* TMU0 */
+#define TMU_BASE 0xFE430000
+
+/* ETHER, GETHER MAC address */
+struct ether_mac_regs {
+ unsigned int reserved[114];
+ unsigned int mahr;
+ unsigned int reserved2;
+ unsigned int malr;
+};
+#define GETHER0_MAC_BASE ((struct ether_mac_regs *)0xfee0400)
+#define GETHER1_MAC_BASE ((struct ether_mac_regs *)0xfee0c00)
+#define ETHER0_MAC_BASE ((struct ether_mac_regs *)0xfef0000)
+#define ETHER1_MAC_BASE ((struct ether_mac_regs *)0xfef0800)
+
+/* GETHER */
+struct gether_control_regs {
+ unsigned int gbecont;
+};
+#define GETHER_CONTROL_BASE ((struct gether_control_regs *)0xffc10100)
+#define GBECONT_RMII1 0x00020000
+#define GBECONT_RMII0 0x00010000
+
+/* SerMux */
+struct sermux_regs {
+ unsigned char smr0;
+ unsigned char smr1;
+ unsigned char smr2;
+ unsigned char smr3;
+ unsigned char smr4;
+ unsigned char smr5;
+};
+#define SERMUX_BASE ((struct sermux_regs *)0xfe470000)
+
+
+/* USB0/1 */
+struct usb_common_regs {
+ unsigned short reserved[129];
+ unsigned short suspmode;
+};
+#define USB0_COMMON_BASE ((struct usb_common_regs *)0xfe450000)
+#define USB1_COMMON_BASE ((struct usb_common_regs *)0xfe4f0000)
+
+struct usb0_phy_regs {
+ unsigned short reset;
+ unsigned short reserved[4];
+ unsigned short portsel;
+};
+#define USB0_PHY_BASE ((struct usb0_phy_regs *)0xfe5f0000)
+
+struct usb1_port_regs {
+ unsigned int port1sel;
+ unsigned int reserved;
+ unsigned int usb1intsts;
+};
+#define USB1_PORT_BASE ((struct usb1_port_regs *)0xfe4f2000)
+
+struct usb1_alignment_regs {
+ unsigned int ehcidatac; /* 0xfe4fe018 */
+ unsigned int reserved[63];
+ unsigned int ohcidatac;
+};
+#define USB1_ALIGNMENT_BASE ((struct usb1_alignment_regs *)0xfe4fe018)
+
+/* GPIO */
+struct gpio_regs {
+ unsigned short pacr;
+ unsigned short pbcr;
+ unsigned short pccr;
+ unsigned short pdcr;
+ unsigned short pecr;
+ unsigned short pfcr;
+ unsigned short pgcr;
+ unsigned short phcr;
+ unsigned short picr;
+ unsigned short pjcr;
+ unsigned short pkcr;
+ unsigned short plcr;
+ unsigned short pmcr;
+ unsigned short pncr;
+ unsigned short pocr;
+ unsigned short reserved;
+ unsigned short pqcr;
+ unsigned short prcr;
+ unsigned short pscr;
+ unsigned short ptcr;
+ unsigned short pucr;
+ unsigned short pvcr;
+ unsigned short pwcr;
+ unsigned short pxcr;
+ unsigned short pycr;
+ unsigned short pzcr;
+ unsigned char padr;
+ unsigned char reserved_a;
+ unsigned char pbdr;
+ unsigned char reserved_b;
+ unsigned char pcdr;
+ unsigned char reserved_c;
+ unsigned char pddr;
+ unsigned char reserved_d;
+ unsigned char pedr;
+ unsigned char reserved_e;
+ unsigned char pfdr;
+ unsigned char reserved_f;
+ unsigned char pgdr;
+ unsigned char reserved_g;
+ unsigned char phdr;
+ unsigned char reserved_h;
+ unsigned char pidr;
+ unsigned char reserved_i;
+ unsigned char pjdr;
+ unsigned char reserved_j;
+ unsigned char pkdr;
+ unsigned char reserved_k;
+ unsigned char pldr;
+ unsigned char reserved_l;
+ unsigned char pmdr;
+ unsigned char reserved_m;
+ unsigned char pndr;
+ unsigned char reserved_n;
+ unsigned char podr;
+ unsigned char reserved_o;
+ unsigned char ppdr;
+ unsigned char reserved_p;
+ unsigned char pqdr;
+ unsigned char reserved_q;
+ unsigned char prdr;
+ unsigned char reserved_r;
+ unsigned char psdr;
+ unsigned char reserved_s;
+ unsigned char ptdr;
+ unsigned char reserved_t;
+ unsigned char pudr;
+ unsigned char reserved_u;
+ unsigned char pvdr;
+ unsigned char reserved_v;
+ unsigned char pwdr;
+ unsigned char reserved_w;
+ unsigned char pxdr;
+ unsigned char reserved_x;
+ unsigned char pydr;
+ unsigned char reserved_y;
+ unsigned char pzdr;
+ unsigned char reserved_z;
+ unsigned short ncer;
+ unsigned short ncmcr;
+ unsigned short nccsr;
+ unsigned char reserved2[2];
+ unsigned short psel0; /* +0x70 */
+ unsigned short psel1;
+ unsigned short psel2;
+ unsigned short psel3;
+ unsigned short psel4;
+ unsigned short psel5;
+ unsigned short psel6;
+ unsigned short reserved3[2];
+ unsigned short psel7;
+};
+#define GPIO_BASE ((struct gpio_regs *)0xffec0000)
+
+#endif /* ifndef __ASSEMBLY__ */
+#endif /* _ASM_CPU_SH7752_H_ */
NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
NETSPACE_V2_OE_LOW, NETSPACE_V2_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
--- /dev/null
+#
+# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+#
+# Based on Kirkwood support:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := $(BOARD).o ../common/common.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# Copyright (C) 2012 Albert ARIBAUD <albert.u.boot@aribaud.net>
+#
+# Based on netspace_v2 kwbimage.cfg:
+# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+#
+# Based on Kirkwood support:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand # Boot from NAND flash
+NAND_PAGE_SIZE 800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Values taken from image original LaCie U-Boot header dump!
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1B1B1B9B
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+
+DATA 0xFFD01404 0x37743000 # DDR Controller Control Low
+
+DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
+
+DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
+
+DATA 0xFFD01410 0x0000CCCC # DDR Address Control
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+
+DATA 0xFFD0141C 0x00000662 # DDR Mode
+
+DATA 0xFFD01420 0x00000004 # DDR Extended Mode
+
+DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
+
+DATA 0xFFD01428 0x00096630 # DDR2 ODT Read Timing (default values)
+
+DATA 0xFFD0147C 0x00009663 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 0x0
+DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+DATA 0xFFD20134 0x66666666
+DATA 0xFFD20138 0x66666666
+DATA 0xFFD10000 0x01112222
+DATA 0xFFD1000C 0x00000000
+DATA 0xFFD10104 0x00000000
+DATA 0xFFD10100 0x40000000
+# End of Header extension
+DATA 0x0 0x0
--- /dev/null
+/*
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * Based on Kirkwood support:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/gpio.h>
+
+#include "../common/common.h"
+#include "netdev.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* GPIO configuration: start FAN at low speed, USB and HDD */
+
+#define WIRELESS_SPACE_OE_LOW 0xFF006808
+#define WIRELESS_SPACE_OE_HIGH 0x0000F989
+#define WIRELESS_SPACE_OE_VAL_LOW 0x00010080
+#define WIRELESS_SPACE_OE_VAL_HIGH 0x00000240
+
+#define WIRELESS_SPACE_REAR_BUTTON 13
+#define WIRELESS_SPACE_FRONT_BUTTON 43
+
+const u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO, /* Fan speed (bit 1) */
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP13_GPIO, /* Red led */
+ MPP14_GPIO, /* USB fuse */
+ MPP15_SATA0_ACTn,
+ MPP16_GPIO, /* SATA 0 power */
+ MPP17_GPIO, /* SATA 1 power */
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0, /* Gigabit Ethernet 1 */
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GE1_8,
+ MPP29_GE1_9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GE1_14,
+ MPP35_GE1_15,
+ MPP36_GPIO, /* Fan speed (bit 2) */
+ MPP37_GPIO, /* Fan speed (bit 0) */
+ MPP38_GPIO, /* Fan power */
+ MPP39_GPIO, /* Fan rotation fail */
+ MPP40_GPIO, /* Ethernet switch link */
+ MPP41_GPIO, /* USB enable host vbus */
+ MPP42_GPIO, /* LED clock control */
+ MPP43_GPIO, /* WPS button (0=Pushed, 1=Released) */
+ MPP44_GPIO, /* Red LED on/off */
+ MPP45_GPIO, /* Red LED timer blink (on=off=100ms) */
+ MPP46_GPIO, /* Green LED on/off */
+ MPP47_GPIO, /* LED (blue, green) SATA activity blink */
+ MPP48_GPIO, /* Blue LED on/off */
+ 0
+};
+
+struct mv88e61xx_config swcfg = {
+ .name = "egiga0",
+ .vlancfg = MV88E61XX_VLANCFG_ROUTER,
+ .rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
+ .led_init = MV88E61XX_LED_INIT_EN,
+ .mdip = MV88E61XX_MDIP_NOCHANGE,
+ .portstate = MV88E61XX_PORTSTT_FORWARDING,
+ .cpuport = 0x20,
+ .ports_enabled = 0x3F,
+};
+
+int board_early_init_f(void)
+{
+ /* Gpio configuration */
+ kw_config_gpio(WIRELESS_SPACE_OE_VAL_LOW, WIRELESS_SPACE_OE_VAL_HIGH,
+ WIRELESS_SPACE_OE_LOW, WIRELESS_SPACE_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ kirkwood_mpp_conf(kwmpp_config, NULL);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Machine number */
+ gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
+
+ /* Boot parameters address */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+#if defined(CONFIG_MISC_INIT_R)
+int misc_init_r(void)
+{
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
+ if (!getenv("ethaddr")) {
+ uchar mac[6];
+ if (lacie_read_mac_address(mac) == 0)
+ eth_setenv_enetaddr("ethaddr", mac);
+ }
+#endif
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
+/* Configure and initialize PHY */
+void reset_phy(void)
+{
+ /* configure switch on egiga0 */
+ mv88e61xx_switch_initialize(&swcfg);
+}
+#endif
+
+#if defined(CONFIG_KIRKWOOD_GPIO) && defined(CONFIG_WIRELESS_SPACE_CMD)
+/* Return GPIO button status */
+static int
+do_ws(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ if (strcmp(argv[1], "button") == 0) {
+ if (strcmp(argv[2], "rear") == 0)
+ /* invert GPIO result for intuitive while/until use */
+ return !kw_gpio_get_value(WIRELESS_SPACE_REAR_BUTTON);
+ else if (strcmp(argv[2], "front") == 0)
+ return kw_gpio_get_value(WIRELESS_SPACE_FRONT_BUTTON);
+ else
+ return -1;
+ } else {
+ return -1;
+ }
+}
+
+U_BOOT_CMD(ws, 3, 0, do_ws,
+ "Return GPIO button status 0=off 1=on",
+ "- ws button rear|front: test buttons' states\n"
+);
+#endif
DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn, /* SPI Flash */
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
GURUPLUG_OE_LOW, GURUPLUG_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
MV88F6281GTW_GE_OE_LOW, MV88F6281GTW_GE_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
OPENRD_OE_LOW, OPENRD_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
RD6281A_OE_LOW, RD6281A_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
SHEEVAPLUG_OE_LOW, SHEEVAPLUG_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
at91_macb_hw_init();
#endif
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+ at91_uhp_hw_init();
+#endif
#ifdef CONFIG_LCD
at91sam9x5ek_lcd_hw_init();
#endif
* you can do this only with a working network connection. Therefore, a random
* ethernet address is generated if none is set and a DHCP request is sent.
* After a successful DHCP response is received, the network settings are
- * configured and the ncip parameter is set to the serverip. Eg. for a working
- * resuce mode, you should set 'next-server' to the host where the netconsole
- * client is started.
+ * configured and the ncip is unset. Therefore, all netconsole packets are
+ * broadcasted.
* Additionally, the bootsource is set to 'rescue'.
*/
* Multi-Purpose Pins Functionality configuration
* These strappings are taken from the original vendor uboot port.
*/
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
POGO_E02_OE_LOW, POGO_E02_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
#include <netdev.h>
#include <net.h>
#include <i2c.h>
+#include <usb.h>
#include <twl4030.h>
#include <linux/compiler.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-types.h>
+#include <asm/ehci-omap.h>
+#include <asm/gpio.h>
#include "eeprom.h"
MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)); /*HSUSB0_DATA6*/
MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)); /*HSUSB0_DATA7*/
+ /* USB EHCI */
+ MUX_VAL(CP(ETK_D0_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT0*/
+ MUX_VAL(CP(ETK_D1_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT1*/
+ MUX_VAL(CP(ETK_D2_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT2*/
+ MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT3*/
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT4*/
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT5*/
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT6*/
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT7*/
+ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DIR*/
+ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_NXT*/
+ MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M3)); /*HSUSB1_CLK*/
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | DIS | M3)); /*HSUSB1_STP*/
+
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DT0*/
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DT1*/
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M3)); /*HSUSB2_DT2*/
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M3)); /*HSUSB2_DT3*/
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | EN | M3)); /*HSUSB2_DT4*/
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | EN | M3)); /*HSUSB2_DT5*/
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M3)); /*HSUSB2_DT6*/
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | EN | M3)); /*HSUSB2_DT7*/
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DIR*/
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_NXT*/
+ MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)); /*HSUSB2_CLK*/
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/
+
+ /* SB_T35_USB_HUB_RESET_GPIO */
+ MUX_VAL(CP(CAM_WEN), (IDIS | PTD | DIS | M4)); /*GPIO_167*/
+
/* I2C1 */
MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)); /*I2C1_SCL*/
MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)); /*I2C1_SDA*/
serialnr->low = 0;
serialnr->high = 0;
};
+
+#ifdef CONFIG_USB_EHCI_OMAP
+struct omap_usbhs_board_data usbhs_bdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+#define SB_T35_USB_HUB_RESET_GPIO 167
+int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ u8 val;
+ int offset;
+
+ if (gpio_request(SB_T35_USB_HUB_RESET_GPIO, "SB-T35 usb hub reset")) {
+ printf("Error: can't obtain GPIO %d for SB-T35 usb hub reset",
+ SB_T35_USB_HUB_RESET_GPIO);
+ return -1;
+ }
+
+ gpio_direction_output(SB_T35_USB_HUB_RESET_GPIO, 0);
+ udelay(10);
+ gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
+ udelay(1000);
+
+ offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_GPIODATADIR1;
+ twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, offset);
+ /* Set GPIO6 and GPIO7 of TPS65930 as output */
+ val |= 0xC0;
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, val, offset);
+ offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_SETGPIODATAOUT1;
+ /* Take both PHYs out of reset */
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0xC0, offset);
+ udelay(1);
+
+ return omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(void)
+{
+ return omap_ehci_hcd_stop();
+}
+
+#endif /* CONFIG_USB_EHCI_OMAP */
DNS325_OE_LOW, DNS325_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
#include <asm/arch/pxa.h>
#include <asm/arch/pxa-regs.h>
#include <asm/io.h>
+#include <usb.h>
DECLARE_GLOBAL_DATA_PTR;
+int board_eth_init(bd_t *bis)
+{
+ usb_eth_initialize(bis);
+ return 0;
+}
+
int board_init(void)
{
/* We have RAM, disable cache */
/* adress of boot parameters */
gd->bd->bi_boot_params = 0xa0000100;
+ /* Let host see that device is disconnected */
+ udc_disconnect();
+ mdelay(500);
+
return 0;
}
ICONNECT_OE_LOW, ICONNECT_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
TK71_OE_LOW, TK71_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
{
#if defined(CONFIG_HARD_I2C) && !defined(MACH_TYPE_KM_KIRKWOOD)
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ;
+ immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
/*
#define MASK_RBI_DEFECT_16 0x01
/* Multi-Purpose Pins Functionality configuration */
-u32 kwmpp_config[] = {
+static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
int misc_init_r(void)
{
- char *str;
- int mach_type;
-
- str = getenv("mach_type");
- if (str != NULL) {
- mach_type = simple_strtoul(str, NULL, 10);
- printf("Overwriting MACH_TYPE with %d!!!\n", mach_type);
- gd->bd->bi_arch_number = mach_type;
- }
#if defined(CONFIG_KM_MGCOGE3UN)
char *wait_for_ne;
wait_for_ne = getenv("waitforne");
int board_init(void)
{
- /*
- * arch number of board
- */
- gd->bd->bi_arch_number = MACH_TYPE_KM_KIRKWOOD;
-
/* address of boot parameters */
gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register
DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
-DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
-DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
-DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
+
+# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
+# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
#Dram initalization
DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register
DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register
DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
-DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
-DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
-DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
+
+# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
+# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
#Dram initalization
DATA 0xFFD01400 0x43000400 # SDRAM Configuration Register
# bit 19-18: 1, ECC RAM WTC RAM0
# bit 31-20: ???,Reserve
-DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
-# bit 23-0: 0x000200, Addr Config tuning
-# bit 31-24: 0, Reserved
-
-# ??? Missing register # CPU RAM Management Control2 Register
-
-DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
-# bit 15-0: 0x1C00, Opmux Tuning
-# bit 31-16: 0, Pc Dp Tuning
-
-DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
-# bit 1-0: 1, addr clk tune
-# bit 3-2: 0, reserved
-# bit 5-4: 0, dtcmp clk tune
-# bit 7-6: 0, reserved
-# bit 9-8: 0, macdrv clk tune
-# bit 11-10: 0, opmuxgm2 clk tune
-# bit 15-14: 0, rf clk tune
-# bit 17-16: 0, rfbypass clk tune
-# bit 19-18: 0, pc dp clk tune
-# bit 23-20: 0, icache clk tune
-# bit 27:24: 0, dcache clk tune
-# bit 31:28: 0, regfile tunin
+# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
+# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
# SDRAM initalization
DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register
# bit 19-18: 1, ECC RAM WTC RAM0
# bit 31-20: ?,Reserved
-DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
-# bit 23-0: 0x000200, Addr Config tuning
-# bit 31-24: 0, Reserved
-
-# ??? Missing register # CPU RAM Management Control2 Register
-
-DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
-# bit 15-0: 0x1C00, Opmux Tuning
-# bit 31-16: 0, Pc Dp Tuning
-
-DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
-# bit 1-0: 1, addr clk tune
-# bit 3-2: 0, reserved
-# bit 5-4: 0, dtcmp clk tune
-# bit 7-6: 0, reserved
-# bit 9-8: 0, macdrv clk tune
-# bit 11-10: 0, opmuxgm2 clk tune
-# bit 15-14: 0, rf clk tune
-# bit 17-16: 0, rfbypass clk tune
-# bit 19-18: 0, pc dp clk tune
-# bit 23-20: 0, icache clk tune
-# bit 27:24: 0, dcache clk tune
-# bit 31:28: 0, regfile tunin
+# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
+# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
# SDRAM initalization
DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register
/* Set SATA activity LEDs to default off */
writel(MVSATAHC_LED_POLARITY_CTRL, MVSATAHC_LED_CONF_REG);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
--- /dev/null
+#
+# Copyright (C) 2012 Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := sh7752evb.o spi-boot.o
+SOBJS := lowlevel_init.o
+
+$(LIB): $(obj).depend $(COBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(COBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * Copyright (C) 2012 Renesas Solutions Corp.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/processor.h>
+#include <asm/macro.h>
+
+.macro or32, addr, data
+ mov.l \addr, r1
+ mov.l \data, r0
+ mov.l @r1, r2
+ or r2, r0
+ mov.l r0, @r1
+.endm
+
+.macro wait_DBCMD
+ mov.l DBWAIT_A, r0
+ mov.l @r0, r1
+.endm
+
+ .global lowlevel_init
+ .section .spiboot1.text
+ .align 2
+
+lowlevel_init:
+ /*------- GPIO -------*/
+ write16 PDCR_A, PDCR_D ! SPI0
+ write16 PGCR_A, PGCR_D ! SPI0, GETHER MDIO gate(PTG1)
+ write16 PJCR_A, PJCR_D ! SCIF4
+ write16 PTCR_A, PTCR_D ! STATUS
+ write16 PSEL1_A, PSEL1_D ! SPI0
+ write16 PSEL2_A, PSEL2_D ! SPI0
+ write16 PSEL5_A, PSEL5_D ! STATUS
+
+ bra exit_gpio
+ nop
+
+ .align 2
+
+/*------- GPIO -------*/
+PDCR_A: .long 0xffec0006
+PGCR_A: .long 0xffec000c
+PJCR_A: .long 0xffec0012
+PTCR_A: .long 0xffec0026
+PSEL1_A: .long 0xffec0072
+PSEL2_A: .long 0xffec0074
+PSEL5_A: .long 0xffec007a
+
+PDCR_D: .long 0x0000
+PGCR_D: .long 0x0004
+PJCR_D: .long 0x0000
+PTCR_D: .long 0x0000
+PSEL1_D: .long 0x0000
+PSEL2_D: .long 0x3000
+PSEL5_D: .long 0x0ffc
+
+ .align 2
+
+exit_gpio:
+ mov #0, r14
+ mova 2f, r0
+ mov.l PC_MASK, r1
+ tst r0, r1
+ bf 2f
+
+ bra exit_pmb
+ nop
+
+ .align 2
+
+/* If CPU runs on SDRAM (PC=0x5???????) or not. */
+PC_MASK: .long 0x20000000
+
+2:
+ mov #1, r14
+
+ mov.l EXPEVT_A, r0
+ mov.l @r0, r0
+ mov.l EXPEVT_POWER_ON_RESET, r1
+ cmp/eq r0, r1
+ bt 1f
+
+ /*
+ * If EXPEVT value is manual reset or tlb multipul-hit,
+ * initialization of DDR3IF is not necessary.
+ */
+ bra exit_ddr
+ nop
+
+1:
+ /*------- Reset -------*/
+ write32 MRSTCR0_A, MRSTCR0_D
+ write32 MRSTCR1_A, MRSTCR1_D
+
+ /* For Core Reset */
+ mov.l DBACEN_A, r0
+ mov.l @r0, r0
+ cmp/eq #0, r0
+ bt 3f
+
+ /*
+ * If DBACEN == 1(DBSC was already enabled), we have to avoid the
+ * initialization of DDR3-SDRAM.
+ */
+ bra exit_ddr
+ nop
+
+3:
+ /*------- DDR3IF -------*/
+ /* oscillation stabilization time */
+ wait_timer WAIT_OSC_TIME
+
+ /* step 3 */
+ write32 DBCMD_A, DBCMD_RSTL_VAL
+ wait_timer WAIT_30US
+
+ /* step 4 */
+ write32 DBCMD_A, DBCMD_PDEN_VAL
+
+ /* step 5 */
+ write32 DBKIND_A, DBKIND_D
+
+ /* step 6 */
+ write32 DBCONF_A, DBCONF_D
+ write32 DBTR0_A, DBTR0_D
+ write32 DBTR1_A, DBTR1_D
+ write32 DBTR2_A, DBTR2_D
+ write32 DBTR3_A, DBTR3_D
+ write32 DBTR4_A, DBTR4_D
+ write32 DBTR5_A, DBTR5_D
+ write32 DBTR6_A, DBTR6_D
+ write32 DBTR7_A, DBTR7_D
+ write32 DBTR8_A, DBTR8_D
+ write32 DBTR9_A, DBTR9_D
+ write32 DBTR10_A, DBTR10_D
+ write32 DBTR11_A, DBTR11_D
+ write32 DBTR12_A, DBTR12_D
+ write32 DBTR13_A, DBTR13_D
+ write32 DBTR14_A, DBTR14_D
+ write32 DBTR15_A, DBTR15_D
+ write32 DBTR16_A, DBTR16_D
+ write32 DBTR17_A, DBTR17_D
+ write32 DBTR18_A, DBTR18_D
+ write32 DBTR19_A, DBTR19_D
+ write32 DBRNK0_A, DBRNK0_D
+
+ /* step 7 */
+ write32 DBPDCNT3_A, DBPDCNT3_D
+
+ /* step 8 */
+ write32 DBPDCNT1_A, DBPDCNT1_D
+ write32 DBPDCNT2_A, DBPDCNT2_D
+ write32 DBPDLCK_A, DBPDLCK_D
+ write32 DBPDRGA_A, DBPDRGA_D
+ write32 DBPDRGD_A, DBPDRGD_D
+
+ /* step 9 */
+ wait_timer WAIT_30US
+
+ /* step 10 */
+ write32 DBPDCNT0_A, DBPDCNT0_D
+
+ /* step 11 */
+ wait_timer WAIT_30US
+ wait_timer WAIT_30US
+
+ /* step 12 */
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+ wait_DBCMD
+
+ /* step 13 */
+ write32 DBCMD_A, DBCMD_RSTH_VAL
+ wait_DBCMD
+
+ /* step 14 */
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+ write32 DBCMD_A, DBCMD_WAIT_VAL
+
+ /* step 15 */
+ write32 DBCMD_A, DBCMD_PDXT_VAL
+
+ /* step 16 */
+ write32 DBCMD_A, DBCMD_MRS2_VAL
+
+ /* step 17 */
+ write32 DBCMD_A, DBCMD_MRS3_VAL
+
+ /* step 18 */
+ write32 DBCMD_A, DBCMD_MRS1_VAL
+
+ /* step 19 */
+ write32 DBCMD_A, DBCMD_MRS0_VAL
+
+ /* step 20 */
+ write32 DBCMD_A, DBCMD_ZQCL_VAL
+
+ write32 DBCMD_A, DBCMD_REF_VAL
+ write32 DBCMD_A, DBCMD_REF_VAL
+ wait_DBCMD
+
+ /* step 21 */
+ write32 DBADJ0_A, DBADJ0_D
+ write32 DBADJ1_A, DBADJ1_D
+ write32 DBADJ2_A, DBADJ2_D
+
+ /* step 22 */
+ write32 DBRFCNF0_A, DBRFCNF0_D
+ write32 DBRFCNF1_A, DBRFCNF1_D
+ write32 DBRFCNF2_A, DBRFCNF2_D
+
+ /* step 23 */
+ write32 DBCALCNF_A, DBCALCNF_D
+
+ /* step 24 */
+ write32 DBRFEN_A, DBRFEN_D
+ write32 DBCMD_A, DBCMD_SRXT_VAL
+
+ /* step 25 */
+ write32 DBACEN_A, DBACEN_D
+
+ /* step 26 */
+ wait_DBCMD
+
+ bra exit_ddr
+ nop
+
+ .align 2
+
+EXPEVT_A: .long 0xff000024
+EXPEVT_POWER_ON_RESET: .long 0x00000000
+
+/*------- Reset -------*/
+MRSTCR0_A: .long 0xffd50030
+MRSTCR0_D: .long 0xfe1ffe7f
+MRSTCR1_A: .long 0xffd50034
+MRSTCR1_D: .long 0xfff3ffff
+
+/*------- DDR3IF -------*/
+DBCMD_A: .long 0xfe800018
+DBKIND_A: .long 0xfe800020
+DBCONF_A: .long 0xfe800024
+DBTR0_A: .long 0xfe800040
+DBTR1_A: .long 0xfe800044
+DBTR2_A: .long 0xfe800048
+DBTR3_A: .long 0xfe800050
+DBTR4_A: .long 0xfe800054
+DBTR5_A: .long 0xfe800058
+DBTR6_A: .long 0xfe80005c
+DBTR7_A: .long 0xfe800060
+DBTR8_A: .long 0xfe800064
+DBTR9_A: .long 0xfe800068
+DBTR10_A: .long 0xfe80006c
+DBTR11_A: .long 0xfe800070
+DBTR12_A: .long 0xfe800074
+DBTR13_A: .long 0xfe800078
+DBTR14_A: .long 0xfe80007c
+DBTR15_A: .long 0xfe800080
+DBTR16_A: .long 0xfe800084
+DBTR17_A: .long 0xfe800088
+DBTR18_A: .long 0xfe80008c
+DBTR19_A: .long 0xfe800090
+DBRNK0_A: .long 0xfe800100
+DBPDCNT0_A: .long 0xfe800200
+DBPDCNT1_A: .long 0xfe800204
+DBPDCNT2_A: .long 0xfe800208
+DBPDCNT3_A: .long 0xfe80020c
+DBPDLCK_A: .long 0xfe800280
+DBPDRGA_A: .long 0xfe800290
+DBPDRGD_A: .long 0xfe8002a0
+DBADJ0_A: .long 0xfe8000c0
+DBADJ1_A: .long 0xfe8000c4
+DBADJ2_A: .long 0xfe8000c8
+DBRFCNF0_A: .long 0xfe8000e0
+DBRFCNF1_A: .long 0xfe8000e4
+DBRFCNF2_A: .long 0xfe8000e8
+DBCALCNF_A: .long 0xfe8000f4
+DBRFEN_A: .long 0xfe800014
+DBACEN_A: .long 0xfe800010
+DBWAIT_A: .long 0xfe80001c
+
+WAIT_OSC_TIME: .long 6000
+WAIT_30US: .long 13333
+
+DBCMD_RSTL_VAL: .long 0x20000000
+DBCMD_PDEN_VAL: .long 0x1000d73c
+DBCMD_WAIT_VAL: .long 0x0000d73c
+DBCMD_RSTH_VAL: .long 0x2100d73c
+DBCMD_PDXT_VAL: .long 0x110000c8
+DBCMD_MRS0_VAL: .long 0x28000930
+DBCMD_MRS1_VAL: .long 0x29000004
+DBCMD_MRS2_VAL: .long 0x2a000008
+DBCMD_MRS3_VAL: .long 0x2b000000
+DBCMD_ZQCL_VAL: .long 0x03000200
+DBCMD_REF_VAL: .long 0x0c000000
+DBCMD_SRXT_VAL: .long 0x19000000
+DBKIND_D: .long 0x00000007
+DBCONF_D: .long 0x0f030a01
+DBTR0_D: .long 0x00000007
+DBTR1_D: .long 0x00000006
+DBTR2_D: .long 0x00000000
+DBTR3_D: .long 0x00000007
+DBTR4_D: .long 0x00070007
+DBTR5_D: .long 0x0000001b
+DBTR6_D: .long 0x00000014
+DBTR7_D: .long 0x00000005
+DBTR8_D: .long 0x00000015
+DBTR9_D: .long 0x00000006
+DBTR10_D: .long 0x00000008
+DBTR11_D: .long 0x00000007
+DBTR12_D: .long 0x0000000e
+DBTR13_D: .long 0x00000056
+DBTR14_D: .long 0x00000006
+DBTR15_D: .long 0x00000004
+DBTR16_D: .long 0x00150002
+DBTR17_D: .long 0x000c0017
+DBTR18_D: .long 0x00000200
+DBTR19_D: .long 0x00000040
+DBRNK0_D: .long 0x00000001
+DBPDCNT0_D: .long 0x00000001
+DBPDCNT1_D: .long 0x00000001
+DBPDCNT2_D: .long 0x00000000
+DBPDCNT3_D: .long 0x00004010
+DBPDLCK_D: .long 0x0000a55a
+DBPDRGA_D: .long 0x00000028
+DBPDRGD_D: .long 0x00017100
+
+DBADJ0_D: .long 0x00000000
+DBADJ1_D: .long 0x00000000
+DBADJ2_D: .long 0x18061806
+DBRFCNF0_D: .long 0x000001ff
+DBRFCNF1_D: .long 0x08001000
+DBRFCNF2_D: .long 0x00000000
+DBCALCNF_D: .long 0x0000ffff
+DBRFEN_D: .long 0x00000001
+DBACEN_D: .long 0x00000001
+
+ .align 2
+exit_ddr:
+#if defined(CONFIG_SH_32BIT)
+ /*------- set PMB -------*/
+ write32 PASCR_A, PASCR_29BIT_D
+ write32 MMUCR_A, MMUCR_D
+
+ /*****************************************************************
+ * ent virt phys v sz c wt
+ * 0 0xa0000000 0x00000000 1 128M 0 1
+ * 1 0xa8000000 0x48000000 1 128M 0 1
+ * 5 0x88000000 0x48000000 1 128M 1 1
+ */
+ write32 PMB_ADDR_SPIBOOT_A, PMB_ADDR_SPIBOOT_D
+ write32 PMB_DATA_SPIBOOT_A, PMB_DATA_SPIBOOT_D
+ write32 PMB_ADDR_DDR_C1_A, PMB_ADDR_DDR_C1_D
+ write32 PMB_DATA_DDR_C1_A, PMB_DATA_DDR_C1_D
+ write32 PMB_ADDR_DDR_N1_A, PMB_ADDR_DDR_N1_D
+ write32 PMB_DATA_DDR_N1_A, PMB_DATA_DDR_N1_D
+
+ write32 PMB_ADDR_ENTRY2, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY3, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY4, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY6, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY7, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY8, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY9, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY10, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY11, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY12, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY13, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY14, PMB_ADDR_NOT_USE_D
+ write32 PMB_ADDR_ENTRY15, PMB_ADDR_NOT_USE_D
+
+ write32 PASCR_A, PASCR_INIT
+ mov.l DUMMY_ADDR, r0
+ icbi @r0
+#endif /* if defined(CONFIG_SH_32BIT) */
+
+exit_pmb:
+ /* CPU is running on ILRAM? */
+ mov r14, r0
+ tst #1, r0
+ bt 1f
+
+ mov.l _stack_ilram, r15
+ mov.l _spiboot_main, r0
+100: bsrf r0
+ nop
+
+ .align 2
+_spiboot_main: .long (spiboot_main - (100b + 4))
+_stack_ilram: .long 0xe5204000
+
+1:
+ write32 CCR_A, CCR_D
+
+ rts
+ nop
+
+ .align 2
+
+#if defined(CONFIG_SH_32BIT)
+/*------- set PMB -------*/
+PMB_ADDR_SPIBOOT_A: .long PMB_ADDR_BASE(0)
+PMB_ADDR_DDR_N1_A: .long PMB_ADDR_BASE(1)
+PMB_ADDR_DDR_C1_A: .long PMB_ADDR_BASE(5)
+PMB_ADDR_ENTRY2: .long PMB_ADDR_BASE(2)
+PMB_ADDR_ENTRY3: .long PMB_ADDR_BASE(3)
+PMB_ADDR_ENTRY4: .long PMB_ADDR_BASE(4)
+PMB_ADDR_ENTRY6: .long PMB_ADDR_BASE(6)
+PMB_ADDR_ENTRY7: .long PMB_ADDR_BASE(7)
+PMB_ADDR_ENTRY8: .long PMB_ADDR_BASE(8)
+PMB_ADDR_ENTRY9: .long PMB_ADDR_BASE(9)
+PMB_ADDR_ENTRY10: .long PMB_ADDR_BASE(10)
+PMB_ADDR_ENTRY11: .long PMB_ADDR_BASE(11)
+PMB_ADDR_ENTRY12: .long PMB_ADDR_BASE(12)
+PMB_ADDR_ENTRY13: .long PMB_ADDR_BASE(13)
+PMB_ADDR_ENTRY14: .long PMB_ADDR_BASE(14)
+PMB_ADDR_ENTRY15: .long PMB_ADDR_BASE(15)
+
+PMB_ADDR_SPIBOOT_D: .long mk_pmb_addr_val(0xa0)
+PMB_ADDR_DDR_C1_D: .long mk_pmb_addr_val(0x88)
+PMB_ADDR_DDR_N1_D: .long mk_pmb_addr_val(0xa8)
+PMB_ADDR_NOT_USE_D: .long 0x00000000
+
+PMB_DATA_SPIBOOT_A: .long PMB_DATA_BASE(0)
+PMB_DATA_DDR_N1_A: .long PMB_DATA_BASE(1)
+PMB_DATA_DDR_C1_A: .long PMB_DATA_BASE(5)
+
+/* ppn ub v s1 s0 c wt */
+PMB_DATA_SPIBOOT_D: .long mk_pmb_data_val(0x00, 0, 1, 1, 0, 0, 1)
+PMB_DATA_DDR_C1_D: .long mk_pmb_data_val(0x48, 0, 1, 1, 0, 1, 1)
+PMB_DATA_DDR_N1_D: .long mk_pmb_data_val(0x48, 1, 1, 1, 0, 0, 1)
+
+PASCR_A: .long 0xff000070
+DUMMY_ADDR: .long 0xa0000000
+PASCR_29BIT_D: .long 0x00000000
+PASCR_INIT: .long 0x80000080
+MMUCR_A: .long 0xff000010
+MMUCR_D: .long 0x00000004 /* clear ITLB */
+#endif /* CONFIG_SH_32BIT */
+
+CCR_A: .long CCR
+CCR_D: .long CCR_CACHE_INIT
--- /dev/null
+/*
+ * Copyright (C) 2012 Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/mmc.h>
+#include <spi_flash.h>
+
+int checkboard(void)
+{
+ puts("BOARD: SH7752 evaluation board (R0P7752C00000RZ)\n");
+
+ return 0;
+}
+
+static void init_gpio(void)
+{
+ struct gpio_regs *gpio = GPIO_BASE;
+ struct sermux_regs *sermux = SERMUX_BASE;
+
+ /* GPIO */
+ writew(0x0000, &gpio->pacr); /* GETHER */
+ writew(0x0001, &gpio->pbcr); /* INTC */
+ writew(0x0000, &gpio->pccr); /* PWMU, INTC */
+ writew(0xeaff, &gpio->pecr); /* GPIO */
+ writew(0x0000, &gpio->pfcr); /* WDT */
+ writew(0x0000, &gpio->phcr); /* SPI1 */
+ writew(0x0000, &gpio->picr); /* SDHI */
+ writew(0x0003, &gpio->pkcr); /* SerMux */
+ writew(0x0000, &gpio->plcr); /* SerMux */
+ writew(0x0000, &gpio->pmcr); /* RIIC */
+ writew(0x0000, &gpio->pncr); /* USB, SGPIO */
+ writew(0x0000, &gpio->pocr); /* SGPIO */
+ writew(0xd555, &gpio->pqcr); /* GPIO */
+ writew(0x0000, &gpio->prcr); /* RIIC */
+ writew(0x0000, &gpio->pscr); /* RIIC */
+ writeb(0x00, &gpio->pudr);
+ writew(0x5555, &gpio->pucr); /* Debug LED */
+ writew(0x0000, &gpio->pvcr); /* RSPI */
+ writew(0x0000, &gpio->pwcr); /* EVC */
+ writew(0x0000, &gpio->pxcr); /* LBSC */
+ writew(0x0000, &gpio->pycr); /* LBSC */
+ writew(0x0000, &gpio->pzcr); /* eMMC */
+ writew(0xfe00, &gpio->psel0);
+ writew(0xff00, &gpio->psel3);
+ writew(0x771f, &gpio->psel4);
+ writew(0x00ff, &gpio->psel6);
+ writew(0xfc00, &gpio->psel7);
+
+ writeb(0x10, &sermux->smr0); /* SMR0: SerMux mode 0 */
+}
+
+static void init_usb_phy(void)
+{
+ struct usb_common_regs *common0 = USB0_COMMON_BASE;
+ struct usb_common_regs *common1 = USB1_COMMON_BASE;
+ struct usb0_phy_regs *phy = USB0_PHY_BASE;
+ struct usb1_port_regs *port = USB1_PORT_BASE;
+ struct usb1_alignment_regs *align = USB1_ALIGNMENT_BASE;
+
+ writew(0x0100, &phy->reset); /* set reset */
+ /* port0 = USB0, port1 = USB1 */
+ writew(0x0002, &phy->portsel);
+ writel(0x0001, &port->port1sel); /* port1 = Host */
+ writew(0x0111, &phy->reset); /* clear reset */
+
+ writew(0x4000, &common0->suspmode);
+ writew(0x4000, &common1->suspmode);
+
+#if defined(__LITTLE_ENDIAN)
+ writel(0x00000000, &align->ehcidatac);
+ writel(0x00000000, &align->ohcidatac);
+#endif
+}
+
+static void init_gether_mdio(void)
+{
+ struct gpio_regs *gpio = GPIO_BASE;
+
+ writew(readw(&gpio->pgcr) | 0x0004, &gpio->pgcr);
+ writeb(readb(&gpio->pgdr) | 0x02, &gpio->pgdr); /* Use ET0-MDIO */
+}
+
+static void set_mac_to_sh_giga_eth_register(int channel, char *mac_string)
+{
+ struct ether_mac_regs *ether;
+ unsigned char mac[6];
+ unsigned long val;
+
+ eth_parse_enetaddr(mac_string, mac);
+
+ if (!channel)
+ ether = GETHER0_MAC_BASE;
+ else
+ ether = GETHER1_MAC_BASE;
+
+ val = (mac[0] << 24) | (mac[1] << 16) | (mac[2] << 8) | mac[3];
+ writel(val, ðer->mahr);
+ val = (mac[4] << 8) | mac[5];
+ writel(val, ðer->malr);
+}
+
+/*****************************************************************
+ * This PMB must be set on this timing. The lowlevel_init is run on
+ * Area 0(phys 0x00000000), so we have to map it.
+ *
+ * The new PMB table is following:
+ * ent virt phys v sz c wt
+ * 0 0xa0000000 0x40000000 1 128M 0 1
+ * 1 0xa8000000 0x48000000 1 128M 0 1
+ * 2 0xb0000000 0x50000000 1 128M 0 1
+ * 3 0xb8000000 0x58000000 1 128M 0 1
+ * 4 0x80000000 0x40000000 1 128M 1 1
+ * 5 0x88000000 0x48000000 1 128M 1 1
+ * 6 0x90000000 0x50000000 1 128M 1 1
+ * 7 0x98000000 0x58000000 1 128M 1 1
+ */
+static void set_pmb_on_board_init(void)
+{
+ struct mmu_regs *mmu = MMU_BASE;
+
+ /* clear ITLB */
+ writel(0x00000004, &mmu->mmucr);
+
+ /* delete PMB for SPIBOOT */
+ writel(0, PMB_ADDR_BASE(0));
+ writel(0, PMB_DATA_BASE(0));
+
+ /* add PMB for SDRAM(0x40000000 - 0x47ffffff) */
+ /* ppn ub v s1 s0 c wt */
+ writel(mk_pmb_addr_val(0xa0), PMB_ADDR_BASE(0));
+ writel(mk_pmb_data_val(0x40, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(0));
+ writel(mk_pmb_addr_val(0xb0), PMB_ADDR_BASE(2));
+ writel(mk_pmb_data_val(0x50, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(2));
+ writel(mk_pmb_addr_val(0xb8), PMB_ADDR_BASE(3));
+ writel(mk_pmb_data_val(0x58, 1, 1, 1, 0, 0, 1), PMB_DATA_BASE(3));
+ writel(mk_pmb_addr_val(0x80), PMB_ADDR_BASE(4));
+ writel(mk_pmb_data_val(0x40, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(4));
+ writel(mk_pmb_addr_val(0x90), PMB_ADDR_BASE(6));
+ writel(mk_pmb_data_val(0x50, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(6));
+ writel(mk_pmb_addr_val(0x98), PMB_ADDR_BASE(7));
+ writel(mk_pmb_data_val(0x58, 0, 1, 1, 0, 1, 1), PMB_DATA_BASE(7));
+}
+
+int board_init(void)
+{
+ init_gpio();
+ set_pmb_on_board_init();
+
+ init_usb_phy();
+ init_gether_mdio();
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
+ printf("DRAM: %dMB\n", CONFIG_SYS_SDRAM_SIZE / (1024 * 1024));
+
+ return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ struct gpio_regs *gpio = GPIO_BASE;
+
+ writew(readw(&gpio->pgcr) | 0x0040, &gpio->pgcr);
+ writeb(readb(&gpio->pgdr) & ~0x08, &gpio->pgdr); /* Reset */
+ udelay(1);
+ writeb(readb(&gpio->pgdr) | 0x08, &gpio->pgdr); /* Release reset */
+ udelay(200);
+
+ return mmcif_mmc_init();
+}
+
+static int get_sh_eth_mac_raw(unsigned char *buf, int size)
+{
+ struct spi_flash *spi;
+ int ret;
+
+ spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
+ if (spi == NULL) {
+ printf("%s: spi_flash probe failed.\n", __func__);
+ return 1;
+ }
+
+ ret = spi_flash_read(spi, SH7752EVB_ETHERNET_MAC_BASE, size, buf);
+ if (ret) {
+ printf("%s: spi_flash read failed.\n", __func__);
+ spi_flash_free(spi);
+ return 1;
+ }
+ spi_flash_free(spi);
+
+ return 0;
+}
+
+static int get_sh_eth_mac(int channel, char *mac_string, unsigned char *buf)
+{
+ memcpy(mac_string, &buf[channel * (SH7752EVB_ETHERNET_MAC_SIZE + 1)],
+ SH7752EVB_ETHERNET_MAC_SIZE);
+ mac_string[SH7752EVB_ETHERNET_MAC_SIZE] = 0x00; /* terminate */
+
+ return 0;
+}
+
+static void init_ethernet_mac(void)
+{
+ char mac_string[64];
+ char env_string[64];
+ int i;
+ unsigned char *buf;
+
+ buf = malloc(256);
+ if (!buf) {
+ printf("%s: malloc failed.\n", __func__);
+ return;
+ }
+ get_sh_eth_mac_raw(buf, 256);
+
+ /* Gigabit Ethernet */
+ for (i = 0; i < SH7752EVB_ETHERNET_NUM_CH; i++) {
+ get_sh_eth_mac(i, mac_string, buf);
+ if (i == 0)
+ setenv("ethaddr", mac_string);
+ else {
+ sprintf(env_string, "eth%daddr", i);
+ setenv(env_string, mac_string);
+ }
+ set_mac_to_sh_giga_eth_register(i, mac_string);
+ }
+
+ free(buf);
+}
+
+int board_late_init(void)
+{
+ init_ethernet_mac();
+
+ return 0;
+}
+
+int do_write_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int i, ret;
+ char mac_string[256];
+ struct spi_flash *spi;
+ unsigned char *buf;
+
+ if (argc != 3) {
+ buf = malloc(256);
+ if (!buf) {
+ printf("%s: malloc failed.\n", __func__);
+ return 1;
+ }
+
+ get_sh_eth_mac_raw(buf, 256);
+
+ /* print current MAC address */
+ for (i = 0; i < SH7752EVB_ETHERNET_NUM_CH; i++) {
+ get_sh_eth_mac(i, mac_string, buf);
+ printf("GETHERC ch%d = %s\n", i, mac_string);
+ }
+ free(buf);
+ return 0;
+ }
+
+ /* new setting */
+ memset(mac_string, 0xff, sizeof(mac_string));
+ sprintf(mac_string, "%s\t%s",
+ argv[1], argv[2]);
+
+ /* write MAC data to SPI rom */
+ spi = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
+ if (!spi) {
+ printf("%s: spi_flash probe failed.\n", __func__);
+ return 1;
+ }
+
+ ret = spi_flash_erase(spi, SH7752EVB_ETHERNET_MAC_BASE_SPI,
+ SH7752EVB_SPI_SECTOR_SIZE);
+ if (ret) {
+ printf("%s: spi_flash erase failed.\n", __func__);
+ return 1;
+ }
+
+ ret = spi_flash_write(spi, SH7752EVB_ETHERNET_MAC_BASE_SPI,
+ sizeof(mac_string), mac_string);
+ if (ret) {
+ printf("%s: spi_flash write failed.\n", __func__);
+ spi_flash_free(spi);
+ return 1;
+ }
+ spi_flash_free(spi);
+
+ puts("The writing of the MAC address to SPI ROM was completed.\n");
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ write_mac, 3, 1, do_write_mac,
+ "write MAC address for GETHERC",
+ "[GETHERC ch0] [GETHERC ch1]\n"
+);
--- /dev/null
+/*
+ * Copyright (C) 2012 Renesas Solutions Corp.
+ *
+ * This file is subject to the terms and conditions of the GNU Lesser
+ * General Public License. See the file "COPYING.LIB" in the main
+ * directory of this archive for more details.
+ */
+
+#include <common.h>
+
+#define CONFIG_RAM_BOOT_PHYS CONFIG_SYS_TEXT_BASE
+#define CONFIG_SPI_ADDR 0x00000000
+#define CONFIG_SPI_LENGTH CONFIG_SYS_MONITOR_LEN
+#define CONFIG_RAM_BOOT CONFIG_SYS_TEXT_BASE
+
+#define SPIWDMADR 0xFE001018
+#define SPIWDMCNTR 0xFE001020
+#define SPIDMCOR 0xFE001028
+#define SPIDMINTSR 0xFE001188
+#define SPIDMINTMR 0xFE001190
+
+#define SPIDMINTSR_DMEND 0x00000004
+
+#define TBR 0xFE002000
+#define RBR 0xFE002000
+
+#define CR1 0xFE002008
+#define CR2 0xFE002010
+#define CR3 0xFE002018
+#define CR4 0xFE002020
+
+/* CR1 */
+#define SPI_TBE 0x80
+#define SPI_TBF 0x40
+#define SPI_RBE 0x20
+#define SPI_RBF 0x10
+#define SPI_PFONRD 0x08
+#define SPI_SSDB 0x04
+#define SPI_SSD 0x02
+#define SPI_SSA 0x01
+
+/* CR2 */
+#define SPI_RSTF 0x80
+#define SPI_LOOPBK 0x40
+#define SPI_CPOL 0x20
+#define SPI_CPHA 0x10
+#define SPI_L1M0 0x08
+
+/* CR4 */
+#define SPI_TBEI 0x80
+#define SPI_TBFI 0x40
+#define SPI_RBEI 0x20
+#define SPI_RBFI 0x10
+#define SPI_SpiS0 0x02
+#define SPI_SSS 0x01
+
+#define spi_write(val, addr) (*(volatile unsigned long *)(addr)) = val
+#define spi_read(addr) (*(volatile unsigned long *)(addr))
+
+/* M25P80 */
+#define M25_READ 0x03
+
+#define __uses_spiboot2 __attribute__((section(".spiboot2.text")))
+static void __uses_spiboot2 spi_reset(void)
+{
+ int timeout = 0x00100000;
+
+ /* Make sure the last transaction is finalized */
+ spi_write(0x00, CR3);
+ spi_write(0x02, CR1);
+ while (!(spi_read(CR4) & SPI_SpiS0)) {
+ if (timeout-- < 0)
+ break;
+ }
+ spi_write(0x00, CR1);
+
+ spi_write(spi_read(CR2) | SPI_RSTF, CR2); /* fifo reset */
+ spi_write(spi_read(CR2) & ~SPI_RSTF, CR2);
+
+ spi_write(0, SPIDMCOR);
+}
+
+static void __uses_spiboot2 spi_read_flash(void *buf, unsigned long addr,
+ unsigned long len)
+{
+ spi_write(M25_READ, TBR);
+ spi_write((addr >> 16) & 0xFF, TBR);
+ spi_write((addr >> 8) & 0xFF, TBR);
+ spi_write(addr & 0xFF, TBR);
+
+ spi_write(SPIDMINTSR_DMEND, SPIDMINTSR);
+ spi_write((unsigned long)buf, SPIWDMADR);
+ spi_write(len & 0xFFFFFFE0, SPIWDMCNTR);
+ spi_write(1, SPIDMCOR);
+
+ spi_write(0xff, CR3);
+ spi_write(spi_read(CR1) | SPI_SSDB, CR1);
+ spi_write(spi_read(CR1) | SPI_SSA, CR1);
+
+ while (!(spi_read(SPIDMINTSR) & SPIDMINTSR_DMEND))
+ ;
+
+ /* Nagate SP0-SS0 */
+ spi_write(0, CR1);
+}
+
+void __uses_spiboot2 spiboot_main(void)
+{
+ void (*_start)(void) = (void *)CONFIG_SYS_TEXT_BASE;
+
+ spi_reset();
+ spi_read_flash((void *)CONFIG_RAM_BOOT_PHYS, CONFIG_SPI_ADDR,
+ CONFIG_SPI_LENGTH);
+
+ _start();
+}
--- /dev/null
+/*
+ * Copyright (C) 2007
+ * Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ *
+ * Copyright (C) 2012
+ * Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-sh-linux", "elf32-sh-linux", "elf32-sh-linux")
+OUTPUT_ARCH(sh)
+ENTRY(_start)
+
+SECTIONS
+{
+ /*
+ * entry and reloct_dst will be provided via ldflags
+ */
+ . = .;
+
+ PROVIDE (_ftext = .);
+ PROVIDE (_fcode = .);
+ PROVIDE (_start = .);
+
+ .text :
+ {
+ KEEP(arch/sh/cpu/sh4/start.o (.text))
+ *(.spiboot1.text)
+ *(.spiboot2.text)
+ . = ALIGN(8192);
+ common/env_embedded.o (.ppcenv)
+ . = ALIGN(8192);
+ common/env_embedded.o (.ppcenvr)
+ . = ALIGN(8192);
+ *(.text)
+ . = ALIGN(4);
+ } =0xFF
+ PROVIDE (_ecode = .);
+ .rodata :
+ {
+ *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
+ . = ALIGN(4);
+ }
+ PROVIDE (_etext = .);
+
+
+ PROVIDE (_fdata = .);
+ .data :
+ {
+ *(.data)
+ . = ALIGN(4);
+ }
+ PROVIDE (_edata = .);
+
+ PROVIDE (_fgot = .);
+ .got :
+ {
+ *(.got)
+ . = ALIGN(4);
+ }
+ PROVIDE (_egot = .);
+
+ .u_boot_list : {
+ #include <u-boot.lst>
+ }
+
+ PROVIDE (reloc_dst_end = .);
+ /* _reloc_dst_end = .; */
+
+ PROVIDE (bss_start = .);
+ PROVIDE (__bss_start = .);
+ .bss (NOLOAD) :
+ {
+ *(.bss)
+ . = ALIGN(4);
+ }
+ PROVIDE (bss_end = .);
+
+ PROVIDE (__bss_end__ = .);
+}
--- /dev/null
+/*
+ * SAMSUNG SMDK5250 board device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ ARCH_CPU_DTS
+
+/ {
+ model = "SAMSUNG SMDK5250 board based on EXYNOS5250";
+ compatible = "samsung,smdk5250", "samsung,exynos5250";
+
+ aliases {
+ i2c0 = "/i2c@12c60000";
+ i2c1 = "/i2c@12c70000";
+ i2c2 = "/i2c@12c80000";
+ i2c3 = "/i2c@12c90000";
+ i2c4 = "/i2c@12ca0000";
+ i2c5 = "/i2c@12cb0000";
+ i2c6 = "/i2c@12cc0000";
+ i2c7 = "/i2c@12cd0000";
+ spi0 = "/spi@12d20000";
+ spi1 = "/spi@12d30000";
+ spi2 = "/spi@12d40000";
+ spi3 = "/spi@131a0000";
+ spi4 = "/spi@131b0000";
+ };
+
+ sromc@12250000 {
+ bank = <1>;
+ srom-timing = <1 9 12 1 6 1 1>;
+ width = <2>;
+ lan@5000000 {
+ compatible = "smsc,lan9215", "smsc,lan";
+ reg = <0x5000000 0x100>;
+ phy-mode = "mii";
+ };
+ };
+
+ sound@12d60000 {
+ samsung,i2s-epll-clock-frequency = <192000000>;
+ samsung,i2s-sampling-rate = <48000>;
+ samsung,i2s-bits-per-sample = <16>;
+ samsung,i2s-channels = <2>;
+ samsung,i2s-lr-clk-framesize = <256>;
+ samsung,i2s-bit-clk-framesize = <32>;
+ samsung,codec-type = "wm8994";
+ };
+
+ i2c@12c70000 {
+ soundcodec@1a {
+ reg = <0x1a>;
+ compatible = "wolfson,wm8994-codec";
+ };
+ };
+
+ i2c@12c60000 {
+ pmic@9 {
+ reg = <0x9>;
+ compatible = "maxim,max77686_pmic";
+ };
+ };
+};
*/
#include <common.h>
+#include <fdtdec.h>
#include <asm/io.h>
#include <i2c.h>
+#include <lcd.h>
#include <netdev.h>
#include <spi.h>
#include <asm/arch/cpu.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
#include <asm/arch/sromc.h>
+#include <asm/arch/dp_info.h>
#include <power/pmic.h>
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_SMC911X
-static int smc9115_pre_init(void)
+#ifdef CONFIG_USB_EHCI_EXYNOS
+int board_usb_vbus_init(void)
{
- u32 smc_bw_conf, smc_bc_conf;
- int err;
-
- /* Ethernet needs data bus width of 16 bits */
- smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK)
- | SROMC_BYTE_ENABLE(CONFIG_ENV_SROM_BANK);
+ struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *)
+ samsung_get_base_gpio_part1();
- smc_bc_conf = SROMC_BC_TACS(0x01) | SROMC_BC_TCOS(0x01)
- | SROMC_BC_TACC(0x06) | SROMC_BC_TCOH(0x01)
- | SROMC_BC_TAH(0x0C) | SROMC_BC_TACP(0x09)
- | SROMC_BC_PMC(0x01);
+ /* Enable VBUS power switch */
+ s5p_gpio_direction_output(&gpio1->x2, 6, 1);
- /* Select and configure the SROMC bank */
- err = exynos_pinmux_config(PERIPH_ID_SROMC,
- CONFIG_ENV_SROM_BANK | PINMUX_FLAG_16BIT);
- if (err) {
- debug("SROMC not configured\n");
- return err;
- }
+ /* VBUS turn ON time */
+ mdelay(3);
- s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf);
return 0;
}
#endif
#ifdef CONFIG_EXYNOS_SPI
spi_init();
#endif
+#ifdef CONFIG_USB_EHCI_EXYNOS
+ board_usb_vbus_init();
+#endif
return 0;
}
PHYS_SDRAM_8_SIZE);
}
+#ifdef CONFIG_OF_CONTROL
+static int decode_sromc(const void *blob, struct fdt_sromc *config)
+{
+ int err;
+ int node;
+
+ node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
+ if (node < 0) {
+ debug("Could not find SROMC node\n");
+ return node;
+ }
+
+ config->bank = fdtdec_get_int(blob, node, "bank", 0);
+ config->width = fdtdec_get_int(blob, node, "width", 2);
+
+ err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
+ FDT_SROM_TIMING_COUNT);
+ if (err < 0) {
+ debug("Could not decode SROMC configuration\n");
+ return -FDT_ERR_NOTFOUND;
+ }
+
+ return 0;
+}
+#endif
+
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_SMC911X
- if (smc9115_pre_init())
+ u32 smc_bw_conf, smc_bc_conf;
+ struct fdt_sromc config;
+ fdt_addr_t base_addr;
+ int node;
+
+#ifdef CONFIG_OF_CONTROL
+ node = decode_sromc(gd->fdt_blob, &config);
+ if (node < 0) {
+ debug("%s: Could not find sromc configuration\n", __func__);
+ return 0;
+ }
+ node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
+ if (node < 0) {
+ debug("%s: Could not find lan9215 configuration\n", __func__);
+ return 0;
+ }
+
+ /* We now have a node, so any problems from now on are errors */
+ base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
+ if (base_addr == FDT_ADDR_T_NONE) {
+ debug("%s: Could not find lan9215 address\n", __func__);
+ return -1;
+ }
+#else
+ /* Non-FDT configuration - bank number and timing parameters*/
+ config.bank = CONFIG_ENV_SROM_BANK;
+ config.width = 2;
+
+ config.timing[FDT_SROM_TACS] = 0x01;
+ config.timing[FDT_SROM_TCOS] = 0x01;
+ config.timing[FDT_SROM_TACC] = 0x06;
+ config.timing[FDT_SROM_TCOH] = 0x01;
+ config.timing[FDT_SROM_TAH] = 0x0C;
+ config.timing[FDT_SROM_TACP] = 0x09;
+ config.timing[FDT_SROM_PMC] = 0x01;
+ base_addr = CONFIG_SMC911X_BASE;
+#endif
+
+ /* Ethernet needs data bus width of 16 bits */
+ if (config.width != 2) {
+ debug("%s: Unsupported bus width %d\n", __func__,
+ config.width);
return -1;
- return smc911x_initialize(0, CONFIG_SMC911X_BASE);
+ }
+ smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
+ | SROMC_BYTE_ENABLE(config.bank);
+
+ smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |\
+ SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |\
+ SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |\
+ SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |\
+ SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |\
+ SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |\
+ SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
+
+ /* Select and configure the SROMC bank */
+ exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
+ s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
+ return smc911x_initialize(0, base_addr);
#endif
return 0;
}
return 0;
}
-#ifdef CONFIG_SYS_I2C_INIT_BOARD
-static int board_i2c_init(void)
-{
- int i, err;
-
- for (i = 0; i < CONFIG_MAX_I2C_NUM; i++) {
- err = exynos_pinmux_config((PERIPH_ID_I2C0 + i),
- PINMUX_FLAG_NONE);
- if (err) {
- debug("I2C%d not configured\n", (PERIPH_ID_I2C0 + i));
- return err;
- }
- }
- i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- return 0;
-}
-#endif
-
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
return err;
}
#ifdef CONFIG_SYS_I2C_INIT_BOARD
- err = board_i2c_init();
+ board_i2c_init(gd->fdt_blob);
#endif
return err;
}
#endif
+
+#ifdef CONFIG_LCD
+void cfg_lcd_gpio(void)
+{
+ struct exynos5_gpio_part1 *gpio1 =
+ (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1();
+
+ /* For Backlight */
+ s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
+ s5p_gpio_set_value(&gpio1->b2, 0, 1);
+
+ /* LCD power on */
+ s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT);
+ s5p_gpio_set_value(&gpio1->x1, 5, 1);
+
+ /* Set Hotplug detect for DP */
+ s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3));
+}
+
+vidinfo_t panel_info = {
+ .vl_freq = 60,
+ .vl_col = 2560,
+ .vl_row = 1600,
+ .vl_width = 2560,
+ .vl_height = 1600,
+ .vl_clkp = CONFIG_SYS_LOW,
+ .vl_hsp = CONFIG_SYS_LOW,
+ .vl_vsp = CONFIG_SYS_LOW,
+ .vl_dp = CONFIG_SYS_LOW,
+ .vl_bpix = 4, /* LCD_BPP = 2^4, for output conosle on LCD */
+
+ /* wDP panel timing infomation */
+ .vl_hspw = 32,
+ .vl_hbpd = 80,
+ .vl_hfpd = 48,
+
+ .vl_vspw = 6,
+ .vl_vbpd = 37,
+ .vl_vfpd = 3,
+ .vl_cmd_allow_len = 0xf,
+
+ .win_id = 3,
+ .cfg_gpio = cfg_lcd_gpio,
+ .backlight_on = NULL,
+ .lcd_power_on = NULL,
+ .reset_lcd = NULL,
+ .dual_lcd_enabled = 0,
+
+ .init_delay = 0,
+ .power_on_delay = 0,
+ .reset_delay = 0,
+ .interface_mode = FIMD_RGB_INTERFACE,
+ .dp_enabled = 1,
+};
+
+static struct edp_device_info edp_info = {
+ .disp_info = {
+ .h_res = 2560,
+ .h_sync_width = 32,
+ .h_back_porch = 80,
+ .h_front_porch = 48,
+ .v_res = 1600,
+ .v_sync_width = 6,
+ .v_back_porch = 37,
+ .v_front_porch = 3,
+ .v_sync_rate = 60,
+ },
+ .lt_info = {
+ .lt_status = DP_LT_NONE,
+ },
+ .video_info = {
+ .master_mode = 0,
+ .bist_mode = DP_DISABLE,
+ .bist_pattern = NO_PATTERN,
+ .h_sync_polarity = 0,
+ .v_sync_polarity = 0,
+ .interlaced = 0,
+ .color_space = COLOR_RGB,
+ .dynamic_range = VESA,
+ .ycbcr_coeff = COLOR_YCBCR601,
+ .color_depth = COLOR_8,
+ },
+};
+
+static struct exynos_dp_platform_data dp_platform_data = {
+ .phy_enable = set_dp_phy_ctrl,
+ .edp_dev_info = &edp_info,
+};
+
+void init_panel_info(vidinfo_t *vid)
+{
+ vid->rgb_mode = MODE_RGB_P,
+
+ exynos_set_dp_platform_data(&dp_platform_data);
+}
+#endif
int board_init(void)
{
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+ gd->bd->bi_boot_params = CONFIG_SYS_SPL_ARGS_ADDR;
check_hw_revision();
printf("HW Revision:\t0x%x\n", board_rev);
at91sam9rlek_dataflash arm arm926ejs at91sam9rlek atmel at91 at91sam9rlek:AT91SAM9RL,SYS_USE_DATAFLASH
at91sam9rlek_nandflash arm arm926ejs at91sam9rlek atmel at91 at91sam9rlek:AT91SAM9RL,SYS_USE_NANDFLASH
at91sam9x5ek_nandflash arm arm926ejs at91sam9x5ek atmel at91 at91sam9x5ek:AT91SAM9X5,SYS_USE_NANDFLASH
+at91sam9x5ek_dataflash arm arm926ejs at91sam9x5ek atmel at91 at91sam9x5ek:AT91SAM9X5,SYS_USE_DATAFLASH
at91sam9x5ek_spiflash arm arm926ejs at91sam9x5ek atmel at91 at91sam9x5ek:AT91SAM9X5,SYS_USE_SPIFLASH
at91sam9x5ek_mmc arm arm926ejs at91sam9x5ek atmel at91 at91sam9x5ek:AT91SAM9X5,SYS_USE_MMC
at91sam9xeek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS0
netspace_max_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:NETSPACE_MAX_V2
netspace_mini_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:NETSPACE_MINI_V2
netspace_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:NETSPACE_V2
+wireless_space arm arm926ejs wireless_space LaCie kirkwood
dreamplug arm arm926ejs - Marvell kirkwood
guruplug arm arm926ejs - Marvell kirkwood
mv88f6281gtw_ge arm arm926ejs - Marvell kirkwood
M5235EVB_Flash32 m68k mcf523x m5235evb freescale - M5235EVB:NORFLASH_PS32BIT,SYS_TEXT_BASE=0xFFC00000
cobra5272 m68k mcf52x2 cobra5272 -
idmr m68k mcf52x2
-eb_cpu5282 m68k mcf52x2 eb_cpu5282 BuS - eb_cpu5282:SYS_TEXT_BASE=0xFF000000
-eb_cpu5282_internal m68k mcf52x2 eb_cpu5282 BuS - eb_cpu5282:SYS_TEXT_BASE=0xF0000000
+eb_cpu5282 m68k mcf52x2 eb_cpu5282 BuS - eb_cpu5282:SYS_TEXT_BASE=0xFF000000,SYS_MONITOR_BASE=0xFF000400
+eb_cpu5282_internal m68k mcf52x2 eb_cpu5282 BuS - eb_cpu5282:SYS_TEXT_BASE=0xF0000000,SYS_MONITOR_BASE=0xF0000418
TASREG m68k mcf52x2 tasreg esd
M5208EVBE m68k mcf52x2 m5208evbe freescale
M5249EVB m68k mcf52x2 m5249evb freescale
MigoR sh sh4 MigoR renesas -
r2dplus sh sh4 r2dplus renesas -
r7780mp sh sh4 r7780mp renesas -
+sh7752evb sh sh4 sh7752evb renesas -
sh7757lcr sh sh4 sh7757lcr renesas -
sh7763rdp sh sh4 sh7763rdp renesas -
sh7785lcr sh sh4 sh7785lcr renesas -
#ifdef CONFIG_NEEDS_MANUAL_RELOC
static int relocated = 0;
- /* relocate boot function table */
if (!relocated) {
int i;
+
+ /* relocate boot function table */
for (i = 0; i < ARRAY_SIZE(boot_os); i++)
if (boot_os[i] != NULL)
boot_os[i] += gd->reloc_off;
+
+ /* relocate names of sub-command table */
+ for (i = 0; i < ARRAY_SIZE(cmd_bootm_sub); i++)
+ cmd_bootm_sub[i].name += gd->reloc_off;
+
relocated = 1;
}
#endif
#include <dataflash.h>
#endif
#include <watchdog.h>
+#include <linux/compiler.h>
+
+DECLARE_GLOBAL_DATA_PTR;
static int mod_mem(cmd_tbl_t *, int, int, int, char * const []);
#endif
+#ifdef CONFIG_CMD_MEMINFO
+__weak void board_show_dram(ulong size)
+{
+ puts("DRAM: ");
+ print_size(size, "\n");
+}
+
+static int do_mem_info(cmd_tbl_t *cmdtp, int flag, int argc,
+ char * const argv[])
+{
+ board_show_dram(gd->ram_size);
+
+ return 0;
+}
+#endif
+
U_BOOT_CMD(
base, 2, 1, do_mem_base,
"print or set address offset",
"[.b, .w, .l] address value delay(ms)"
);
#endif /* CONFIG_MX_CYCLIC */
+
+#ifdef CONFIG_CMD_MEMINFO
+U_BOOT_CMD(
+ meminfo, 3, 1, do_mem_info,
+ "display memory information",
+ ""
+);
+#endif
int w;
/* Validate arguments */
- if ((argc != 5) || (strlen(argv[3]) != 1))
+ if (argc != 5 && argc != 3)
+ return CMD_RET_USAGE;
+ if (argc == 5 && strlen(argv[3]) != 1)
return CMD_RET_USAGE;
w = cmd_get_data_size(argv[0], 4);
a = get_arg(argv[2], w);
+
+ if (argc == 3) {
+ sprintf(buf, "%lx", a);
+ setenv(argv[1], buf);
+
+ return 0;
+ }
+
b = get_arg(argv[4], w);
switch (argv[3][0]) {
U_BOOT_CMD(
setexpr, 5, 0, do_setexpr,
"set environment variable as the result of eval expression",
- "[.b, .w, .l] name value1 <op> value2\n"
+ "[.b, .w, .l] name [*]value1 <op> [*]value2\n"
" - set environment variable 'name' to the result of the evaluated\n"
" express specified by <op>. <op> can be &, |, ^, +, -, *, /, %\n"
- " size argument is only meaningful if value1 and/or value2 are memory addresses"
+ " size argument is only meaningful if value1 and/or value2 are\n"
+ " memory addresses (*)\n"
+ "setexpr[.b, .w, .l] name *value\n"
+ " - load a memory address into a variable"
);
* Licensed under the GPL-2 or later.
*/
+#include <div64.h>
#include <common.h>
#include <malloc.h>
#include <spi_flash.h>
return 1;
}
+/**
+ * This function takes a byte length and a delta unit of time to compute the
+ * approximate bytes per second
+ *
+ * @param len amount of bytes currently processed
+ * @param start_ms start time of processing in ms
+ * @return bytes per second if OK, 0 on error
+ */
+static ulong bytes_per_second(unsigned int len, ulong start_ms)
+{
+ /* less accurate but avoids overflow */
+ if (len >= ((unsigned int) -1) / 1024)
+ return len / (max(get_timer(start_ms) / 1024, 1));
+ else
+ return 1024 * len / max(get_timer(start_ms), 1);
+}
+
static int do_spi_flash_probe(int argc, char * const argv[])
{
unsigned int bus = CONFIG_SF_DEFAULT_BUS;
const char *end = buf + len;
size_t todo; /* number of bytes to do in this pass */
size_t skipped = 0; /* statistics */
+ const ulong start_time = get_timer(0);
+ size_t scale = 1;
+ const char *start_buf = buf;
+ ulong delta;
+ if (end - buf >= 200)
+ scale = (end - buf) / 100;
cmp_buf = malloc(flash->sector_size);
if (cmp_buf) {
+ ulong last_update = get_timer(0);
+
for (; buf < end && !err_oper; buf += todo, offset += todo) {
todo = min(end - buf, flash->sector_size);
+ if (get_timer(last_update) > 100) {
+ printf(" \rUpdating, %zu%% %lu B/s",
+ 100 - (end - buf) / scale,
+ bytes_per_second(buf - start_buf,
+ start_time));
+ last_update = get_timer(0);
+ }
err_oper = spi_flash_update_block(flash, offset, todo,
buf, cmp_buf, &skipped);
}
err_oper = "malloc";
}
free(cmp_buf);
+ putc('\r');
if (err_oper) {
printf("SPI flash failed in %s step\n", err_oper);
return 1;
}
- printf("%zu bytes written, %zu bytes skipped\n", len - skipped,
- skipped);
+
+ delta = get_timer(start_time);
+ printf("%zu bytes written, %zu bytes skipped", len - skipped,
+ skipped);
+ printf(" in %ld.%lds, speed %ld B/s\n",
+ delta / 1000, delta % 1000, bytes_per_second(len, start_time));
return 0;
}
return 0;
}
+#ifdef CONFIG_CMD_SF_TEST
+enum {
+ STAGE_ERASE,
+ STAGE_CHECK,
+ STAGE_WRITE,
+ STAGE_READ,
+
+ STAGE_COUNT,
+};
+
+static char *stage_name[STAGE_COUNT] = {
+ "erase",
+ "check",
+ "write",
+ "read",
+};
+
+struct test_info {
+ int stage;
+ int bytes;
+ unsigned base_ms;
+ unsigned time_ms[STAGE_COUNT];
+};
+
+static void show_time(struct test_info *test, int stage)
+{
+ uint64_t speed; /* KiB/s */
+ int bps; /* Bits per second */
+
+ speed = (long long)test->bytes * 1000;
+ do_div(speed, test->time_ms[stage] * 1024);
+ bps = speed * 8;
+
+ printf("%d %s: %d ticks, %d KiB/s %d.%03d Mbps\n", stage,
+ stage_name[stage], test->time_ms[stage],
+ (int)speed, bps / 1000, bps % 1000);
+}
+
+static void spi_test_next_stage(struct test_info *test)
+{
+ test->time_ms[test->stage] = get_timer(test->base_ms);
+ show_time(test, test->stage);
+ test->base_ms = get_timer(0);
+ test->stage++;
+}
+
+/**
+ * Run a test on the SPI flash
+ *
+ * @param flash SPI flash to use
+ * @param buf Source buffer for data to write
+ * @param len Size of data to read/write
+ * @param offset Offset within flash to check
+ * @param vbuf Verification buffer
+ * @return 0 if ok, -1 on error
+ */
+static int spi_flash_test(struct spi_flash *flash, char *buf, ulong len,
+ ulong offset, char *vbuf)
+{
+ struct test_info test;
+ int i;
+
+ printf("SPI flash test:\n");
+ memset(&test, '\0', sizeof(test));
+ test.base_ms = get_timer(0);
+ test.bytes = len;
+ if (spi_flash_erase(flash, offset, len)) {
+ printf("Erase failed\n");
+ return -1;
+ }
+ spi_test_next_stage(&test);
+
+ if (spi_flash_read(flash, offset, len, vbuf)) {
+ printf("Check read failed\n");
+ return -1;
+ }
+ for (i = 0; i < len; i++) {
+ if (vbuf[i] != 0xff) {
+ printf("Check failed at %d\n", i);
+ print_buffer(i, vbuf + i, 1, min(len - i, 0x40), 0);
+ return -1;
+ }
+ }
+ spi_test_next_stage(&test);
+
+ if (spi_flash_write(flash, offset, len, buf)) {
+ printf("Write failed\n");
+ return -1;
+ }
+ memset(vbuf, '\0', len);
+ spi_test_next_stage(&test);
+
+ if (spi_flash_read(flash, offset, len, vbuf)) {
+ printf("Read failed\n");
+ return -1;
+ }
+ spi_test_next_stage(&test);
+
+ for (i = 0; i < len; i++) {
+ if (buf[i] != vbuf[i]) {
+ printf("Verify failed at %d, good data:\n", i);
+ print_buffer(i, buf + i, 1, min(len - i, 0x40), 0);
+ printf("Bad data:\n");
+ print_buffer(i, vbuf + i, 1, min(len - i, 0x40), 0);
+ return -1;
+ }
+ }
+ printf("Test passed\n");
+ for (i = 0; i < STAGE_COUNT; i++)
+ show_time(&test, i);
+
+ return 0;
+}
+
+static int do_spi_flash_test(int argc, char * const argv[])
+{
+ unsigned long offset;
+ unsigned long len;
+ char *buf = (char *)CONFIG_SYS_TEXT_BASE;
+ char *endp;
+ char *vbuf;
+ int ret;
+
+ offset = simple_strtoul(argv[1], &endp, 16);
+ if (*argv[1] == 0 || *endp != 0)
+ return -1;
+ len = simple_strtoul(argv[2], &endp, 16);
+ if (*argv[2] == 0 || *endp != 0)
+ return -1;
+
+ vbuf = malloc(len);
+ if (!vbuf) {
+ printf("Cannot allocate memory\n");
+ return 1;
+ }
+ buf = malloc(len);
+ if (!buf) {
+ free(vbuf);
+ printf("Cannot allocate memory\n");
+ return 1;
+ }
+
+ memcpy(buf, (char *)CONFIG_SYS_TEXT_BASE, len);
+ ret = spi_flash_test(flash, buf, len, offset, vbuf);
+ free(vbuf);
+ free(buf);
+ if (ret) {
+ printf("Test failed\n");
+ return 1;
+ }
+
+ return 0;
+}
+#endif /* CONFIG_CMD_SF_TEST */
+
static int do_spi_flash(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
const char *cmd;
ret = do_spi_flash_read_write(argc, argv);
else if (strcmp(cmd, "erase") == 0)
ret = do_spi_flash_erase(argc, argv);
+#ifdef CONFIG_CMD_SF_TEST
+ else if (!strcmp(cmd, "test"))
+ ret = do_spi_flash_test(argc, argv);
+#endif
else
ret = -1;
return CMD_RET_USAGE;
}
+#ifdef CONFIG_CMD_SF_TEST
+#define SF_TEST_HELP "\nsf test offset len " \
+ "- run a very basic destructive test"
+#else
+#define SF_TEST_HELP
+#endif
+
U_BOOT_CMD(
sf, 5, 1, do_spi_flash,
"SPI flash sub-system",
" `+len' round up `len' to block size\n"
"sf update addr offset len - erase and write `len' bytes from memory\n"
" at `addr' to flash at `offset'"
+ SF_TEST_HELP
);
{
int ret;
- ret = sound_init();
+ ret = sound_init(gd->fdt_blob);
if (ret) {
printf("Initialise Audio driver failed\n");
return CMD_RET_FAILURE;
#include <command.h>
#include <version.h>
#include <linux/compiler.h>
+#ifdef CONFIG_SYS_COREBOOT
+#include <asm/arch/sysinfo.h>
+#endif
const char __weak version_string[] = U_BOOT_VERSION_STRING;
#ifdef LD_VERSION_STRING
puts(LD_VERSION_STRING "\n");
#endif
-
+#ifdef CONFIG_SYS_COREBOOT
+ printf("coreboot-%s (%s)\n", lib_sysinfo.version, lib_sysinfo.build);
+#endif
return 0;
}
return &usb_dev[dev_index - 1];
}
+/*
+ * Free the newly created device node.
+ * Called in error cases where configuring a newly attached
+ * device fails for some reason.
+ */
+void usb_free_device(void)
+{
+ dev_index--;
+ USB_PRINTF("Freeing device node: %d\n", dev_index);
+ memset(&usb_dev[dev_index], 0, sizeof(struct usb_device));
+ usb_dev[dev_index].devnum = -1;
+}
/*
* By the time we get here, the device has gotten a new device ID
/* Run it through the hoops (find a driver, etc) */
if (usb_new_device(usb)) {
/* Woops, disable the port */
+ usb_free_device();
+ dev->children[port] = NULL;
USB_HUB_PRINTF("hub: disabling port %d\n", port + 1);
usb_clear_port_feature(dev, port + 1, USB_PORT_FEAT_ENABLE);
}
for (i = 0; i < dev->maxchild; i++) {
ALLOC_CACHE_ALIGN_BUFFER(struct usb_port_status, portsts, 1);
unsigned short portstatus, portchange;
+ int ret;
+ ulong start = get_timer(0);
+
+ /*
+ * Wait for (whichever finishes first)
+ * - A maximum of 10 seconds
+ * This is a purely observational value driven by connecting
+ * a few broken pen drives and taking the max * 1.5 approach
+ * - connection_change and connection state to report same
+ * state
+ */
+ do {
+ ret = usb_get_port_status(dev, i + 1, portsts);
+ if (ret < 0) {
+ USB_HUB_PRINTF("get_port_status failed\n");
+ break;
+ }
+
+ portstatus = le16_to_cpu(portsts->wPortStatus);
+ portchange = le16_to_cpu(portsts->wPortChange);
+
+ if ((portchange & USB_PORT_STAT_C_CONNECTION) ==
+ (portstatus & USB_PORT_STAT_CONNECTION))
+ break;
+
+ mdelay(100);
+ } while (get_timer(start) < CONFIG_SYS_HZ * 10);
- if (usb_get_port_status(dev, i + 1, portsts) < 0) {
- USB_HUB_PRINTF("get_port_status failed\n");
+ if (ret < 0)
continue;
- }
- portstatus = le16_to_cpu(portsts->wPortStatus);
- portchange = le16_to_cpu(portsts->wPortChange);
USB_HUB_PRINTF("Port %d Status %X Change %X\n",
i + 1, portstatus, portchange);
return 0;
}
usb_request_sense(srb, ss);
+ /*
+ * Check the Key Code Qualifier, if it matches
+ * "Not Ready - medium not present"
+ * (the sense Key equals 0x2 and the ASC is 0x3a)
+ * return immediately as the medium being absent won't change
+ * unless there is a user action.
+ */
+ if ((srb->sense_buf[2] == 0x02) &&
+ (srb->sense_buf[12] == 0x3a))
+ return -1;
mdelay(100);
} while (retries--);
--- /dev/null
+========================================
+Renesas R0P7752C00000RZ board
+========================================
+
+This board specification:
+=========================
+
+The R0P7752C00000RZ(board config name:sh7752evb) has the following device:
+
+ - SH7752 (SH-4A)
+ - DDR3-SDRAM 512MB
+ - SPI ROM 8MB
+ - Gigabit Ethernet controllers
+ - eMMC 4GB
+
+
+Configuration for This board:
+=============================
+
+You can select the configuration as follows:
+
+ - make sh7752evb_config
+
+
+This board specific command:
+============================
+
+This board has the following its specific command:
+
+ - write_mac
+
+
+1. write_mac
+
+You can write MAC address to SPI ROM.
+
+ Usage 1) Write MAC address
+
+ write_mac [GETHERC ch0] [GETHERC ch1]
+
+ For example)
+ => write_mac 74:90:50:00:33:9e 74:90:50:00:33:9f
+ *) We have to input the command as a single line
+ (without carriage return)
+ *) We have to reset after input the command.
+
+ Usage 2) Show current data
+
+ write_mac
+
+ For example)
+ => write_mac
+ GETHERC ch0 = 74:90:50:00:33:9e
+ GETHERC ch1 = 74:90:50:00:33:9f
+
+
+Update SPI ROM:
+============================
+
+1. Copy u-boot image to RAM area.
+2. Probe SPI device.
+ => sf probe 0
+ SF: Detected MX25L6405D with page size 64KiB, total 8 MiB
+3. Erase SPI ROM.
+ => sf erase 0 80000
+4. Write u-boot image to SPI ROM.
+ => sf write 0x48000000 0 80000
Storage USB Commands:
- usb scan: scans the USB for storage devices.The USB must be
running for this command (usb start)
-- usb device [dev]: show or set current USB staorage device
+- usb device [dev]: show or set current USB storage device
- usb part [dev]: print partition table of one or all USB storage
devices
- usb read addr blk# cnt:
--- /dev/null
+Exynos ISP SPI Subsystem
+
+The device node for ISP SPI subsytem.
+Since Peripheral id in EXYNOS is decoded based on Interrupts, currently
+ISP SPI have no individual interrupts hence we add ad dummy interrupt node
+which will have a value beyond the maximum number of interrupts exynos5 can
+support.
+
+Required properties :
+ - compatible : Should be "samsung,exynos-spi" for spi.
+ - reg : Base adrress of the the subsystem.
+ - interrupts : A value which is beyond the maximum number of interrupts
+exynos5 can support.
+
+Example:
+spi@131a0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "samsung,exynos-spi";
+ reg = <0x131a0000 0x30>;
+ interrupts = <0 129 0>;
+};
--- /dev/null
+Exynos Sound Subsystem
+
+The device node for sound subsytem which contains codec and i2s block
+that is a part of Exynos5250
+
+Required properties :
+ - compatible : Should be "samsung,exynos-sound" for sound
+ - samsung,i2s-epll-clock-frequency : epll clock output frequency in Hz
+ - samsung,i2s-sampling-rate : sampling rate, default is 48000
+ - samsung,i2s-bits-per-sample : sample width, defalut is 16 bit
+ - samsung,i2s-channels : nummber of channels, default is 2
+ - samsung,i2s-lr-clk-framesize : lr clock frame size
+ - samsung,i2s-bit-clk-framesize : bit clock frame size
+ - samsung,codec-type : sound codec type
+
+Example:
+
+sound@12d60000 {
+ compatible = "samsung,exynos-sound"
+ samsung,i2s-epll-clock-frequency = <192000000>;
+ samsung,i2s-sampling-rate = <48000>;
+ samsung,i2s-bits-per-sample = <16>;
+ samsung,i2s-channels = <2>;
+ samsung,i2s-lr-clk-framesize = <256>;
+ samsung,i2s-bit-clk-framesize = <32>;
+ samsung,codec-type = "wm8994";
+};
*/
#include <common.h>
+#include <fdtdec.h>
#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
#include <asm/arch/clk.h>
#include <asm/arch/cpu.h>
+#include <asm/arch/pinmux.h>
#else
#include <asm/arch/s3c24x0_cpu.h>
#endif
#define I2C_TIMEOUT 1 /* 1 second */
-static unsigned int g_current_bus; /* Stores Current I2C Bus */
+/*
+ * For SPL boot some boards need i2c before SDRAM is initialised so force
+ * variables to live in SRAM
+ */
+static unsigned int g_current_bus __attribute__((section(".data")));
+#ifdef CONFIG_OF_CONTROL
+static int i2c_busses __attribute__((section(".data")));
+static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM]
+ __attribute__((section(".data")));
+#endif
#if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
static int GetI2CSDA(void)
(i2c, I2C_WRITE, chip << 1, &xaddr[4 - alen], alen, buffer,
len) != 0);
}
+
+#ifdef CONFIG_OF_CONTROL
+void board_i2c_init(const void *blob)
+{
+ int node_list[CONFIG_MAX_I2C_NUM];
+ int count, i;
+
+ count = fdtdec_find_aliases_for_id(blob, "i2c",
+ COMPAT_SAMSUNG_S3C2440_I2C, node_list,
+ CONFIG_MAX_I2C_NUM);
+
+ for (i = 0; i < count; i++) {
+ struct s3c24x0_i2c_bus *bus;
+ int node = node_list[i];
+
+ if (node <= 0)
+ continue;
+ bus = &i2c_bus[i];
+ bus->regs = (struct s3c24x0_i2c *)
+ fdtdec_get_addr(blob, node, "reg");
+ bus->id = pinmux_decode_periph_id(blob, node);
+ bus->node = node;
+ bus->bus_num = i2c_busses++;
+ exynos_pinmux_config(bus->id, 0);
+ }
+}
+
+static struct s3c24x0_i2c_bus *get_bus(unsigned int bus_idx)
+{
+ if (bus_idx < i2c_busses)
+ return &i2c_bus[bus_idx];
+
+ debug("Undefined bus: %d\n", bus_idx);
+ return NULL;
+}
+
+int i2c_get_bus_num_fdt(int node)
+{
+ int i;
+
+ for (i = 0; i < i2c_busses; i++) {
+ if (node == i2c_bus[i].node)
+ return i;
+ }
+
+ debug("%s: Can't find any matched I2C bus\n", __func__);
+ return -1;
+}
+
+int i2c_reset_port_fdt(const void *blob, int node)
+{
+ struct s3c24x0_i2c_bus *i2c;
+ int bus;
+
+ bus = i2c_get_bus_num_fdt(node);
+ if (bus < 0) {
+ debug("could not get bus for node %d\n", node);
+ return -1;
+ }
+
+ i2c = get_bus(bus);
+ if (!i2c) {
+ debug("get_bus() failed for node node %d\n", node);
+ return -1;
+ }
+
+ i2c_ch_init(i2c->regs, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ return 0;
+}
+#endif
+
#endif /* CONFIG_HARD_I2C */
u32 iicds;
u32 iiclc;
};
+
+struct s3c24x0_i2c_bus {
+ int node; /* device tree node */
+ int bus_num; /* i2c bus number */
+ struct s3c24x0_i2c *regs;
+ int id;
+};
#endif /* _S3C24X0_I2C_H */
AMD_CMD_ERASE_START);
flash_unlock_seq (info, sect);
flash_write_cmd (info, sect, 0,
- AMD_CMD_ERASE_SECTOR);
+ info->cmd_erase_sector);
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
printf(info->chipwidth == FLASH_CFI_16BIT ? "%04X" : "%02X",
info->device_id2);
}
+ if ((info->vendor == CFI_CMDSET_AMD_STANDARD) && (info->legacy_unlock))
+ printf("\n Advanced Sector Protection (PPB) enabled");
printf ("\n Erase timeout: %ld ms, write timeout: %ld ms\n",
info->erase_blk_tout,
info->write_tout);
return flash_write_cfiword (info, wp, cword);
}
+static inline int manufact_match(flash_info_t *info, u32 manu)
+{
+ return info->manufacturer_id == ((manu & FLASH_VENDMASK) >> 16);
+}
+
/*-----------------------------------------------------------------------
*/
#ifdef CONFIG_SYS_FLASH_PROTECTION
static int cfi_protect_bugfix(flash_info_t *info, long sector, int prot)
{
- if (info->manufacturer_id == ((INTEL_MANUFACT & FLASH_VENDMASK) >> 16)
+ if (manufact_match(info, INTEL_MANUFACT)
&& info->device_id == NUMONYX_256MBIT) {
/*
* see errata called
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
/* U-Boot only checks the first byte */
- if (info->manufacturer_id ==
- ((ATM_MANUFACT & FLASH_VENDMASK) >> 16)) {
+ if (manufact_match(info, ATM_MANUFACT)) {
if (prot) {
flash_unlock_seq (info, 0);
flash_write_cmd (info, 0,
0, ATM_CMD_UNLOCK_SECT);
}
}
- if (info->manufacturer_id ==
- ((AMD_MANUFACT & FLASH_VENDMASK) >> 16)) {
+ if (info->legacy_unlock) {
int flag = disable_interrupts();
int lock_flag;
static int cmdset_amd_init(flash_info_t *info, struct cfi_qry *qry)
{
info->cmd_reset = AMD_CMD_RESET;
+ info->cmd_erase_sector = AMD_CMD_ERASE_SECTOR;
cmdset_amd_read_jedec_ids(info);
flash_write_cmd(info, 0, info->cfi_offset, FLASH_CMD_CFI);
#ifdef CONFIG_SYS_FLASH_PROTECTION
- if (info->ext_addr && info->manufacturer_id ==
- ((AMD_MANUFACT & FLASH_VENDMASK) >> 16)) {
- ushort spus;
-
- /* read sector protect/unprotect scheme */
- spus = flash_read_uchar(info, info->ext_addr + 9);
- if (spus == 0x8)
+ if (info->ext_addr) {
+ /* read sector protect/unprotect scheme (at 0x49) */
+ if (flash_read_uchar(info, info->ext_addr + 9) == 0x8)
info->legacy_unlock = 1;
}
#endif
}
}
+static void flash_fixup_sst(flash_info_t *info, struct cfi_qry *qry)
+{
+ /*
+ * SST, for many recent nor parallel flashes, says they are
+ * CFI-conformant. This is not true, since qry struct.
+ * reports a std. AMD command set (0x0002), while SST allows to
+ * erase two different sector sizes for the same memory.
+ * 64KB sector (SST call it block) needs 0x30 to be erased.
+ * 4KB sector (SST call it sector) needs 0x50 to be erased.
+ * Since CFI query detect the 4KB number of sectors, users expects
+ * a sector granularity of 4KB, and it is here set.
+ */
+ if (info->device_id == 0x5D23 || /* SST39VF3201B */
+ info->device_id == 0x5C23) { /* SST39VF3202B */
+ /* set sector granularity to 4KB */
+ info->cmd_erase_sector=0x50;
+ }
+}
+
/*
* The following code cannot be run from FLASH!
*
case 0x0020:
flash_fixup_stm(info, &qry);
break;
+ case 0x00bf: /* SST */
+ flash_fixup_sst(info, &qry);
+ break;
}
debug ("manufacturer is %d\n", info->vendor);
FLASH_OFFSET_PROTECT,
FLASH_STATUS_PROTECT);
break;
+ case CFI_CMDSET_AMD_EXTENDED:
+ case CFI_CMDSET_AMD_STANDARD:
+ if (!info->legacy_unlock) {
+ /* default: not protected */
+ info->protect[sect_cnt] = 0;
+ break;
+ }
+
+ /* Read protection (PPB) from sector */
+ flash_write_cmd(info, 0, 0,
+ info->cmd_reset);
+ flash_unlock_seq(info, 0);
+ flash_write_cmd(info, 0,
+ info->addr_unlock1,
+ FLASH_CMD_READ_ID);
+ info->protect[sect_cnt] =
+ flash_isset(
+ info, sect_cnt,
+ FLASH_OFFSET_PROTECT,
+ FLASH_STATUS_PROTECT);
+ break;
default:
/* default: not protected */
info->protect[sect_cnt] = 0;
COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
COBJS-$(CONFIG_NAND_PLAT) += nand_plat.o
+else # minimal SPL drivers
+
+COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_spl.o
+
endif # drivers
endif # nand
timing = IFC_FIR_OP_RBCD;
out_be32(&ifc->ifc_nand.nand_fir0,
- (IFC_FIR_OP_CMD0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
(IFC_FIR_OP_UA << IFC_NAND_FIR0_OP1_SHIFT) |
(timing << IFC_NAND_FIR0_OP2_SHIFT));
out_be32(&ifc->ifc_nand.nand_fcr0,
/* READID */
out_be32(&ifc->ifc_nand.nand_fir0,
- (IFC_FIR_OP_CMD0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
(IFC_FIR_OP_UA << IFC_NAND_FIR0_OP1_SHIFT) |
(IFC_FIR_OP_RB << IFC_NAND_FIR0_OP2_SHIFT));
out_be32(&ifc->ifc_nand.nand_fcr0,
#include <netdev.h>
#include "mv88e61xx.h"
+/*
+ * Uncomment either of the following line for local debug control;
+ * otherwise global debug control will apply.
+ */
+
+/* #undef DEBUG */
+/* #define DEBUG */
+
#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
/* Chip Address mode
* The Switch support two modes of operation
return 0;
}
-static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data)
+static void mv88e61xx_switch_write(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 data)
{
u16 mii_dev_addr;
15));
}
-static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data)
+static void mv88e61xx_switch_read(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 *data)
{
u16 mii_dev_addr;
}
#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
-static void mv88e61xx_port_vlan_config(struct mv88e61xx_config *swconfig,
- u32 max_prtnum, u32 ports_ofs)
-{
- u32 prt;
- u16 reg;
- char *name = swconfig->name;
- u32 cpu_port = swconfig->cpuport;
- u32 port_mask = swconfig->ports_enabled;
- enum mv88e61xx_cfg_vlan vlancfg = swconfig->vlancfg;
-
- /* be sure all ports are disabled */
- for (prt = 0; prt < max_prtnum; prt++) {
- RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, ®);
- reg &= ~0x3;
- WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, reg);
-
- if (!(cpu_port & (1 << prt)))
- continue;
- /* Set CPU port VID to 0x1 */
- RD_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, ®);
- reg &= ~0xfff;
- reg |= 0x1;
- WR_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, reg);
- }
-
- /* Setting Port default priority for all ports to zero */
- for (prt = 0; prt < max_prtnum; prt++) {
- RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, ®);
- reg &= ~0xc000;
- WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, reg);
- }
- /* Setting VID and VID map for all ports except CPU port */
- for (prt = 0; prt < max_prtnum; prt++) {
- /* only for enabled ports */
- if ((1 << prt) & port_mask) {
- /* skip CPU port */
- if ((1 << prt) & cpu_port) {
- /*
- * Set Vlan map table for cpu_port to see
- * all ports
- */
- RD_PHY(name, (ports_ofs + prt),
- MV88E61XX_PRT_VMAP_REG, ®);
- reg &= ~((1 << max_prtnum) - 1);
- reg |= port_mask & ~(1 << prt);
- WR_PHY(name, (ports_ofs + prt),
- MV88E61XX_PRT_VMAP_REG, reg);
- } else {
-
- /*
- * set Ports VLAN Mapping.
- * port prt <--> cpu_port VLAN #prt+1.
- */
- RD_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_VID_REG, ®);
- reg &= ~0x0fff;
- reg |= (prt + 1);
- WR_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_VID_REG, reg);
-
- RD_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_VMAP_REG, ®);
- if (vlancfg == MV88E61XX_VLANCFG_DEFAULT) {
- /*
- * all any port can send frames to all other ports
- * ref: sec 3.2.1.1 of datasheet
- */
- reg |= 0x03f;
- reg &= ~(1 << prt);
- } else if (vlancfg == MV88E61XX_VLANCFG_ROUTER) {
- /*
- * all other ports can send frames to CPU port only
- * ref: sec 3.2.1.2 of datasheet
- */
- reg &= ~((1 << max_prtnum) - 1);
- reg |= cpu_port;
- }
- WR_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_VMAP_REG, reg);
- }
- }
- }
+/*
+ * Convenience macros for switch device/port reads/writes
+ * These macros output valid 'mv88e61xx' U_BOOT_CMDs
+ */
- /*
- * enable only appropriate ports to forwarding mode
- * and disable the others
- */
- for (prt = 0; prt < max_prtnum; prt++) {
- if ((1 << prt) & port_mask) {
- RD_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_CTRL_REG, ®);
- reg |= 0x3;
- WR_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_CTRL_REG, reg);
- } else {
- /* Disable port */
- RD_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_CTRL_REG, ®);
- reg &= ~0x3;
- WR_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_CTRL_REG, reg);
- }
- }
+#ifndef DEBUG
+#define WR_SWITCH_REG wr_switch_reg
+#define RD_SWITCH_REG rd_switch_reg
+#define WR_SWITCH_PORT_REG(n, p, r, d) \
+ WR_SWITCH_REG(n, (MV88E61XX_PRT_OFST+p), r, d)
+#define RD_SWITCH_PORT_REG(n, p, r, d) \
+ RD_SWITCH_REG(n, (MV88E61XX_PRT_OFST+p), r, d)
+#else
+static void WR_SWITCH_REG(char *name, u32 dev_adr, u32 reg_ofs, u16 data)
+{
+ printf("mv88e61xx %s dev %02x reg %02x write %04x\n",
+ name, dev_adr, reg_ofs, data);
+ wr_switch_reg(name, dev_adr, reg_ofs, data);
}
+static void RD_SWITCH_REG(char *name, u32 dev_adr, u32 reg_ofs, u16 *data)
+{
+ rd_switch_reg(name, dev_adr, reg_ofs, data);
+ printf("mv88e61xx %s dev %02x reg %02x read %04x\n",
+ name, dev_adr, reg_ofs, *data);
+}
+static void WR_SWITCH_PORT_REG(char *name, u32 prt_adr, u32 reg_ofs,
+ u16 data)
+{
+ printf("mv88e61xx %s port %02x reg %02x write %04x\n",
+ name, prt_adr, reg_ofs, data);
+ wr_switch_reg(name, (MV88E61XX_PRT_OFST+prt_adr), reg_ofs, data);
+}
+static void RD_SWITCH_PORT_REG(char *name, u32 prt_adr, u32 reg_ofs,
+ u16 *data)
+{
+ rd_switch_reg(name, (MV88E61XX_PRT_OFST+prt_adr), reg_ofs, data);
+ printf("mv88e61xx %s port %02x reg %02x read %04x\n",
+ name, prt_adr, reg_ofs, *data);
+}
+#endif
+
+/*
+ * Local functions to read/write registers on the switch PHYs.
+ * NOTE! This goes through switch, not direct miiphy, writes and reads!
+ */
/*
* Make sure SMIBusy bit cleared before another
u16 reg = 0;
u32 timeout = MV88E61XX_PHY_TIMEOUT;
do {
- RD_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+ rd_switch_reg(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, ®);
if (timeout-- == 0) {
printf("SMI busy timeout\n");
return 0;
}
+static inline int mv88e61xx_switch_miiphy_write(char *name, u32 phy,
+ u32 reg, u16 data)
+{
+ /* write switch data reg then cmd reg then check completion */
+ wr_switch_reg(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA,
+ data);
+ wr_switch_reg(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_CMD,
+ (MV88E61XX_PHY_WRITE_CMD | (phy << 5) | reg));
+ return mv88e61xx_busychk(name);
+}
+
+static inline int mv88e61xx_switch_miiphy_read(char *name, u32 phy,
+ u32 reg, u16 *data)
+{
+ /* write switch cmd reg, check for completion */
+ wr_switch_reg(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_CMD,
+ (MV88E61XX_PHY_READ_CMD | (phy << 5) | reg));
+ if (mv88e61xx_busychk(name))
+ return -1;
+ /* read switch data reg and return success */
+ rd_switch_reg(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, data);
+ return 0;
+}
+
+/*
+ * Convenience macros for switch PHY reads/writes
+ */
+
+#ifndef DEBUG
+#define WR_SWITCH_PHY_REG mv88e61xx_switch_miiphy_write
+#define RD_SWITCH_PHY_REG mv88e61xx_switch_miiphy_read
+#else
+static inline int WR_SWITCH_PHY_REG(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 data)
+{
+ int r = mv88e61xx_switch_miiphy_write(name, phy_adr, reg_ofs, data);
+ if (r)
+ printf("** ERROR writing mv88e61xx %s phy %02x reg %02x\n",
+ name, phy_adr, reg_ofs);
+ else
+ printf("mv88e61xx %s phy %02x reg %02x write %04x\n",
+ name, phy_adr, reg_ofs, data);
+ return r;
+}
+static inline int RD_SWITCH_PHY_REG(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 *data)
+{
+ int r = mv88e61xx_switch_miiphy_read(name, phy_adr, reg_ofs, data);
+ if (r)
+ printf("** ERROR reading mv88e61xx %s phy %02x reg %02x\n",
+ name, phy_adr, reg_ofs);
+ else
+ printf("mv88e61xx %s phy %02x reg %02x read %04x\n",
+ name, phy_adr, reg_ofs, *data);
+ return r;
+}
+#endif
+
+static void mv88e61xx_port_vlan_config(struct mv88e61xx_config *swconfig)
+{
+ u32 prt;
+ u16 reg;
+ char *name = swconfig->name;
+ u32 port_mask = swconfig->ports_enabled;
+
+ /* apply internal vlan config */
+ for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
+ /* only for enabled ports */
+ if ((1 << prt) & port_mask) {
+ /* take vlan map from swconfig */
+ u8 vlanmap = swconfig->vlancfg[prt];
+ /* remove disabled ports from vlan map */
+ vlanmap &= swconfig->ports_enabled;
+ /* apply vlan map to port */
+ RD_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_VMAP_REG, ®);
+ reg &= ~((1 << MV88E61XX_MAX_PORTS_NUM) - 1);
+ reg |= vlanmap;
+ WR_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_VMAP_REG, reg);
+ }
+ }
+}
+
/*
* Power up the specified port and reset PHY
*/
-static int mv88361xx_powerup(struct mv88e61xx_config *swconfig, u32 prt)
+static int mv88361xx_powerup(struct mv88e61xx_config *swconfig, u32 phy)
{
char *name = swconfig->name;
- /* Write Copper Specific control reg1 (0x14) for-
+ /* Write Copper Specific control reg1 (0x10) for-
* Enable Phy power up
* Energy Detect on (sense&Xmit NLP Periodically
* reset other settings default
*/
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x3360);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (0x9410 | (prt << 5)));
-
- if (mv88e61xx_busychk(name))
+ if (WR_SWITCH_PHY_REG(name, phy, 0x10, 0x3360))
return -1;
/* Write PHY ctrl reg (0x0) to apply
* Phy reset (set bit 15 low)
* reset other default values
*/
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x1140);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (0x9400 | (prt << 5)));
-
- if (mv88e61xx_busychk(name))
+ if (WR_SWITCH_PHY_REG(name, phy, 0x00, 0x9140))
return -1;
return 0;
* to setup PHY LEDs default configuration to detect 10/100/1000Mb/s
* Link status
*/
-static int mv88361xx_led_init(struct mv88e61xx_config *swconfig, u32 prt)
+static int mv88361xx_led_init(struct mv88e61xx_config *swconfig, u32 phy)
{
char *name = swconfig->name;
- u16 reg;
if (swconfig->led_init != MV88E61XX_LED_INIT_EN)
return 0;
/* set page address to 3 */
- reg = 3;
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
- 1 << MV88E61XX_MODE_OFST |
- 1 << MV88E61XX_OP_OFST |
- prt << MV88E61XX_ADDR_OFST | 22));
-
- if (mv88e61xx_busychk(name))
+ if (WR_SWITCH_PHY_REG(name, phy, 0x16, 0x0003))
return -1;
- /* set LED Func Ctrl reg */
- reg = 1; /* LED[0] On-Link, Blink-Activity, Off-NoLink */
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
- 1 << MV88E61XX_MODE_OFST |
- 1 << MV88E61XX_OP_OFST |
- prt << MV88E61XX_ADDR_OFST | 16));
-
- if (mv88e61xx_busychk(name))
+ /*
+ * set LED Func Ctrl reg
+ * value 0x0001 = LED[0] On-Link, Blink-Activity, Off-NoLink
+ */
+ if (WR_SWITCH_PHY_REG(name, phy, 0x10, 0x0001))
return -1;
/* set page address to 0 */
- reg = 0;
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
- 1 << MV88E61XX_MODE_OFST |
- 1 << MV88E61XX_OP_OFST |
- prt << MV88E61XX_ADDR_OFST | 22));
-
- if (mv88e61xx_busychk(name))
+ if (WR_SWITCH_PHY_REG(name, phy, 0x16, 0x0000))
return -1;
return 0;
* This is optional settings may be needed on some boards
* for PHY<->magnetics h/w tuning
*/
-static int mv88361xx_reverse_mdipn(struct mv88e61xx_config *swconfig, u32 prt)
+static int mv88361xx_reverse_mdipn(struct mv88e61xx_config *swconfig, u32 phy)
{
char *name = swconfig->name;
- u16 reg;
if (swconfig->mdip != MV88E61XX_MDIP_REVERSE)
return 0;
- reg = 0x0f; /*Reverse MDIP/N[3:0] bits */
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
- 1 << MV88E61XX_MODE_OFST |
- 1 << MV88E61XX_OP_OFST |
- prt << MV88E61XX_ADDR_OFST | 20));
-
- if (mv88e61xx_busychk(name))
+ /*Reverse MDIP/N[3:0] bits */
+ if (WR_SWITCH_PHY_REG(name, phy, 0x14, 0x000f))
return -1;
return 0;
u16 reg;
char *idstr;
char *name = swconfig->name;
+ int time;
if (miiphy_set_current_dev(name)) {
printf("%s failed\n", __FUNCTION__);
printf("Invalid cpu port config, using default port5\n");
}
- RD_PHY(name, MV88E61XX_PRT_OFST, MII_PHYSID2, ®);
+ RD_SWITCH_PORT_REG(name, 0, MII_PHYSID2, ®);
switch (reg &= 0xfff0) {
case 0x1610:
idstr = "88E6161";
break;
}
- /* Port based VLANs configuration */
- if ((swconfig->vlancfg == MV88E61XX_VLANCFG_DEFAULT)
- || (swconfig->vlancfg == MV88E61XX_VLANCFG_ROUTER))
- mv88e61xx_port_vlan_config(swconfig, MV88E61XX_MAX_PORTS_NUM,
- MV88E61XX_PRT_OFST);
- else {
- printf("Unsupported mode %s failed\n", __FUNCTION__);
- return -1;
+ /* be sure all ports are disabled */
+ for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
+ RD_SWITCH_PORT_REG(name, prt, MV88E61XX_PRT_CTRL_REG, ®);
+ reg &= ~0x3;
+ WR_SWITCH_PORT_REG(name, prt, MV88E61XX_PRT_CTRL_REG, reg);
}
+ /* wait 2 ms for queues to drain */
+ udelay(2000);
+
+ /* reset switch */
+ RD_SWITCH_REG(name, MV88E61XX_GLBREG_DEVADR, MV88E61XX_SGCR, ®);
+ reg |= 0x8000;
+ WR_SWITCH_REG(name, MV88E61XX_GLBREG_DEVADR, MV88E61XX_SGCR, reg);
+
+ /* wait up to 1 second for switch reset complete */
+ for (time = 1000; time; time--) {
+ RD_SWITCH_REG(name, MV88E61XX_GLBREG_DEVADR, MV88E61XX_SGSR,
+ ®);
+ if ((reg & 0xc800) == 0xc800)
+ break;
+ udelay(1000);
+ }
+ if (!time)
+ return -1;
+
+ /* Port based VLANs configuration */
+ mv88e61xx_port_vlan_config(swconfig);
+
if (swconfig->rgmii_delay == MV88E61XX_RGMII_DELAY_EN) {
/*
* Enable RGMII delay on Tx and Rx for CPU port
* Ref: sec 9.5 of chip datasheet-02
*/
- WR_PHY(name, MV88E61XX_PRT_OFST + 5,
- MV88E61XX_RGMII_TIMECTRL_REG, 0x18);
- WR_PHY(name, MV88E61XX_PRT_OFST + 4,
- MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7);
+ /*Force port link down */
+ WR_SWITCH_PORT_REG(name, 5, MV88E61XX_PCS_CTRL_REG, 0x10);
+ /* configure port RGMII delay */
+ WR_SWITCH_PORT_REG(name, 4,
+ MV88E61XX_RGMII_TIMECTRL_REG, 0x81e7);
+ RD_SWITCH_PORT_REG(name, 5,
+ MV88E61XX_RGMII_TIMECTRL_REG, ®);
+ WR_SWITCH_PORT_REG(name, 5,
+ MV88E61XX_RGMII_TIMECTRL_REG, reg | 0x18);
+ WR_SWITCH_PORT_REG(name, 4,
+ MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7);
+ /* Force port to RGMII FDX 1000Base then up */
+ WR_SWITCH_PORT_REG(name, 5, MV88E61XX_PCS_CTRL_REG, 0x1e);
+ WR_SWITCH_PORT_REG(name, 5, MV88E61XX_PCS_CTRL_REG, 0x3e);
}
for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
- if (!((1 << prt) & swconfig->cpuport)) {
- if (mv88361xx_led_init(swconfig, prt))
+ /* configure port's PHY */
+ if (!((1 << prt) & swconfig->cpuport)) {
+ /* port 4 has phy 6, not 4 */
+ int phy = (prt == 4) ? 6 : prt;
+ if (mv88361xx_powerup(swconfig, phy))
return -1;
- if (mv88361xx_reverse_mdipn(swconfig, prt))
+ if (mv88361xx_reverse_mdipn(swconfig, phy))
return -1;
- if (mv88361xx_powerup(swconfig, prt))
+ if (mv88361xx_led_init(swconfig, phy))
return -1;
}
+ /* set port VID to port+1 except for cpu port */
+ if (!((1 << prt) & swconfig->cpuport)) {
+ RD_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_VID_REG, ®);
+ WR_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_VID_REG,
+ (reg & ~1023) | (prt+1));
+ }
+
/*Program port state */
- RD_PHY(name, MV88E61XX_PRT_OFST + prt,
- MV88E61XX_PRT_CTRL_REG, ®);
- WR_PHY(name, MV88E61XX_PRT_OFST + prt,
- MV88E61XX_PRT_CTRL_REG,
- reg | (swconfig->portstate & 0x03));
+ RD_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_CTRL_REG, ®);
+ WR_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_CTRL_REG,
+ reg | (swconfig->portstate & 0x03));
+
}
printf("%s Initialized on %s\n", idstr, name);
return 0;
}
+
+#ifdef CONFIG_MV88E61XX_CMD
+static int
+do_switch(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ char *name, *endp;
+ int write = 0;
+ enum { dev, prt, phy } target = dev;
+ u32 addrlo, addrhi, addr;
+ u32 reglo, reghi, reg;
+ u16 data, rdata;
+
+ if (argc < 7)
+ return -1;
+
+ name = argv[1];
+
+ if (strcmp(argv[2], "phy") == 0)
+ target = phy;
+ else if (strcmp(argv[2], "port") == 0)
+ target = prt;
+ else if (strcmp(argv[2], "dev") != 0)
+ return 1;
+
+ addrlo = simple_strtoul(argv[3], &endp, 16);
+
+ if (!*endp) {
+ addrhi = addrlo;
+ } else {
+ while (*endp < '0' || *endp > '9')
+ endp++;
+ addrhi = simple_strtoul(endp, NULL, 16);
+ }
+
+ reglo = simple_strtoul(argv[5], &endp, 16);
+ if (!*endp) {
+ reghi = reglo;
+ } else {
+ while (*endp < '0' || *endp > '9')
+ endp++;
+ reghi = simple_strtoul(endp, NULL, 16);
+ }
+
+ if (strcmp(argv[6], "write") == 0)
+ write = 1;
+ else if (strcmp(argv[6], "read") != 0)
+ return 1;
+
+ data = simple_strtoul(argv[7], NULL, 16);
+
+ for (addr = addrlo; addr <= addrhi; addr++) {
+ for (reg = reglo; reg <= reghi; reg++) {
+ if (write) {
+ if (target == phy)
+ mv88e61xx_switch_miiphy_write(
+ name, addr, reg, data);
+ else if (target == prt)
+ wr_switch_reg(name,
+ addr+MV88E61XX_PRT_OFST,
+ reg, data);
+ else
+ wr_switch_reg(name, addr, reg, data);
+ } else {
+ if (target == phy)
+ mv88e61xx_switch_miiphy_read(
+ name, addr, reg, &rdata);
+ else if (target == prt)
+ rd_switch_reg(name,
+ addr+MV88E61XX_PRT_OFST,
+ reg, &rdata);
+ else
+ rd_switch_reg(name, addr, reg, &rdata);
+ printf("%s %s %s %02x %s %02x %s %04x\n",
+ argv[0], argv[1], argv[2], addr,
+ argv[4], reg, argv[6], rdata);
+ if (write && argc == 7 && rdata != data)
+ return 1;
+ }
+ }
+ }
+ return 0;
+}
+
+U_BOOT_CMD(mv88e61xx, 8, 0, do_switch,
+ "Read or write mv88e61xx switch registers",
+ "<ethdevice> dev|port|phy <addr> reg <reg> write <data>\n"
+ "<ethdevice> dev|port|phy <addr> reg <reg> read [<data>]\n"
+ " - read/write switch device, port or phy at (addr,reg)\n"
+ " addr=0..0x1C for dev, 0..5 for port or phy.\n"
+ " reg=0..0x1F.\n"
+ " data=0..0xFFFF (tested if present against actual read).\n"
+ " All numeric parameters are assumed to be hex.\n"
+ " <addr> and <<reg> arguments can be ranges (x..y)"
+);
+#endif /* CONFIG_MV88E61XX_CMD */
#include <miiphy.h>
#define MV88E61XX_CPU_PORT 0x5
-#define MV88E61XX_MAX_PORTS_NUM 0x6
#define MV88E61XX_PHY_TIMEOUT 100000
-#define MV88E61XX_PRT_STS_REG 0x1
+/* port dev-addr (= port + 0x10) */
+#define MV88E61XX_PRT_OFST 0x10
+/* port registers */
+#define MV88E61XX_PCS_CTRL_REG 0x1
#define MV88E61XX_PRT_CTRL_REG 0x4
#define MV88E61XX_PRT_VMAP_REG 0x6
#define MV88E61XX_PRT_VID_REG 0x7
+#define MV88E61XX_RGMII_TIMECTRL_REG 0x1A
-#define MV88E61XX_PRT_OFST 0x10
+/* global registers dev-addr */
+#define MV88E61XX_GLBREG_DEVADR 0x1B
+/* global registers */
+#define MV88E61XX_SGSR 0x00
+#define MV88E61XX_SGCR 0x04
+
+/* global 2 registers dev-addr */
+#define MV88E61XX_GLB2REG_DEVADR 0x1C
+/* global 2 registers */
#define MV88E61XX_PHY_CMD 0x18
#define MV88E61XX_PHY_DATA 0x19
-#define MV88E61XX_RGMII_TIMECTRL_REG 0x1A
-#define MV88E61XX_GLB2REG_DEVADR 0x1C
+/* global 2 phy commands */
+#define MV88E61XX_PHY_WRITE_CMD 0x9400
+#define MV88E61XX_PHY_READ_CMD 0x9800
#define MV88E61XX_BUSY_OFST 15
#define MV88E61XX_MODE_OFST 12
-#define MV88E61XX_OP_OFST 10
+#define MV88E61XX_OP_OFST 10
#define MV88E61XX_ADDR_OFST 5
#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
static int mv88e61xx_busychk_multic(char *name, u32 devaddr);
-static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data);
-static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data);
-#define WR_PHY mv88e61xx_wr_phy
-#define RD_PHY mv88e61xx_rd_phy
+static void mv88e61xx_switch_write(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 data);
+static void mv88e61xx_switch_read(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 *data);
+#define wr_switch_reg mv88e61xx_switch_write
+#define rd_switch_reg mv88e61xx_switch_read
#else
-#define WR_PHY miiphy_write
-#define RD_PHY miiphy_read
+/* switch appears a s simple PHY and can thus use miiphy */
+#define wr_switch_reg miiphy_write
+#define rd_switch_reg miiphy_read
#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
#endif /* _MV88E61XX_H */
*/
#include <common.h>
+#include <fdtdec.h>
+#include <i2c.h>
#include <power/pmic.h>
#include <power/max77686_pmic.h>
#include <errno.h>
+DECLARE_GLOBAL_DATA_PTR;
+
int pmic_init(unsigned char bus)
{
static const char name[] = "MAX77686_PMIC";
return -ENOMEM;
}
- puts("Board PMIC init\n");
+#ifdef CONFIG_OF_CONTROL
+ const void *blob = gd->fdt_blob;
+ int node, parent;
+
+ node = fdtdec_next_compatible(blob, 0, COMPAT_MAXIM_MAX77686_PMIC);
+ if (node < 0) {
+ debug("PMIC: No node for PMIC Chip in device tree\n");
+ debug("node = %d\n", node);
+ return -1;
+ }
+
+ parent = fdt_parent_offset(blob, node);
+ if (parent < 0) {
+ debug("%s: Cannot find node parent\n", __func__);
+ return -1;
+ }
+
+ p->bus = i2c_get_bus_num_fdt(parent);
+ if (p->bus < 0) {
+ debug("%s: Cannot find I2C bus\n", __func__);
+ return -1;
+ }
+ p->hw.i2c.addr = fdtdec_get_int(blob, node, "reg", 9);
+#else
+ p->bus = bus;
+ p->hw.i2c.addr = MAX77686_I2C_ADDR;
+#endif
+
p->name = name;
p->interface = PMIC_I2C;
p->number_of_regs = PMIC_NUM_OF_REGS;
- p->hw.i2c.addr = MAX77686_I2C_ADDR;
p->hw.i2c.tx_num = 1;
- p->bus = bus;
+
+ puts("Board PMIC init\n");
return 0;
}
void NS16550_init(NS16550_t com_port, int baud_divisor)
{
+#if (!defined(CONFIG_SYS_NS16550_BROKEN_TEMT))
while (!(serial_in(&com_port->lsr) & UART_LSR_TEMT))
;
+#endif
serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);
#if (defined(CONFIG_OMAP) && !defined(CONFIG_OMAP3_ZOOM2)) || \
#elif defined(CONFIG_H8S2678)
# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */
# define H8300_SCI_DR(ch) (*(volatile char *)(P1DR + h8300_sci_pins[ch].port))
-#elif defined(CONFIG_CPU_SH7757)
+#elif defined(CONFIG_CPU_SH7757) || defined(CONFIG_CPU_SH7752)
# define SCSPTR0 0xfe4b0020
# define SCSPTR1 0xfe4b0020
# define SCSPTR2 0xfe4b0020
#include <malloc.h>
#include <common.h>
#include <asm/io.h>
+#include <libfdt.h>
+#include <fdtdec.h>
#include <i2c.h>
#include <i2s.h>
#include <sound.h>
-#include "wm8994.h"
#include <asm/arch/sound.h>
+#include "wm8994.h"
/* defines */
#define SOUND_400_HZ 400
#define SOUND_BITS_IN_BYTE 8
static struct i2stx_info g_i2stx_pri;
-static struct sound_codec_info g_codec_info;
/*
- * get_sound_fdt_values gets fdt values for i2s parameters
+ * get_sound_i2s_values gets values for i2s parameters
*
* @param i2stx_info i2s transmitter transfer param structure
- * @param blob FDT blob
- */
-static void get_sound_i2s_values(struct i2stx_info *i2s)
-{
- i2s->base_address = samsung_get_base_i2s();
- i2s->audio_pll_clk = I2S_PLL_CLK;
- i2s->samplingrate = I2S_SAMPLING_RATE;
- i2s->bitspersample = I2S_BITS_PER_SAMPLE;
- i2s->channels = I2S_CHANNELS;
- i2s->rfs = I2S_RFS;
- i2s->bfs = I2S_BFS;
-}
-
-/*
- * Gets fdt values for wm8994 config parameters
- *
- * @param pcodec_info codec information structure
- * @param blob FDT blob
- * @return int value, 0 for success
+ * @param blob FDT blob if enabled else NULL
*/
-static int get_sound_wm8994_values(struct sound_codec_info *pcodec_info)
+static int get_sound_i2s_values(struct i2stx_info *i2s, const void *blob)
{
+#ifdef CONFIG_OF_CONTROL
+ int node;
int error = 0;
+ int base;
- switch (AUDIO_COMPAT) {
- case AUDIO_COMPAT_SPI:
- debug("%s: Support not added for SPI interface\n", __func__);
+ node = fdtdec_next_compatible(blob, 0,
+ COMPAT_SAMSUNG_EXYNOS5_SOUND);
+ if (node <= 0) {
+ debug("EXYNOS_SOUND: No node for sound in device tree\n");
return -1;
- break;
- case AUDIO_COMPAT_I2C:
- pcodec_info->i2c_bus = AUDIO_I2C_BUS;
- pcodec_info->i2c_dev_addr = AUDIO_I2C_REG;
- debug("i2c dev addr = %d\n", pcodec_info->i2c_dev_addr);
- break;
- default:
- debug("%s: Unknown compat id %d\n", __func__, AUDIO_COMPAT);
+ }
+
+ /*
+ * Get the pre-defined sound specific values from FDT.
+ * All of these are expected to be correct otherwise
+ * wrong register values in i2s setup parameters
+ * may result in no sound play.
+ */
+ base = fdtdec_get_addr(blob, node, "reg");
+ if (base == FDT_ADDR_T_NONE) {
+ debug("%s: Missing i2s base\n", __func__);
return -1;
}
+ i2s->base_address = base;
+ i2s->audio_pll_clk = fdtdec_get_int(blob,
+ node, "samsung,i2s-epll-clock-frequency", -1);
+ error |= i2s->audio_pll_clk;
+ debug("audio_pll_clk = %d\n", i2s->audio_pll_clk);
+ i2s->samplingrate = fdtdec_get_int(blob,
+ node, "samsung,i2s-sampling-rate", -1);
+ error |= i2s->samplingrate;
+ debug("samplingrate = %d\n", i2s->samplingrate);
+ i2s->bitspersample = fdtdec_get_int(blob,
+ node, "samsung,i2s-bits-per-sample", -1);
+ error |= i2s->bitspersample;
+ debug("bitspersample = %d\n", i2s->bitspersample);
+ i2s->channels = fdtdec_get_int(blob,
+ node, "samsung,i2s-channels", -1);
+ error |= i2s->channels;
+ debug("channels = %d\n", i2s->channels);
+ i2s->rfs = fdtdec_get_int(blob,
+ node, "samsung,i2s-lr-clk-framesize", -1);
+ error |= i2s->rfs;
+ debug("rfs = %d\n", i2s->rfs);
+ i2s->bfs = fdtdec_get_int(blob,
+ node, "samsung,i2s-bit-clk-framesize", -1);
+ error |= i2s->bfs;
+ debug("bfs = %d\n", i2s->bfs);
if (error == -1) {
- debug("fail to get wm8994 codec node properties\n");
+ debug("fail to get sound i2s node properties\n");
return -1;
}
-
+#else
+ i2s->base_address = samsung_get_base_i2s();
+ i2s->audio_pll_clk = I2S_PLL_CLK;
+ i2s->samplingrate = I2S_SAMPLING_RATE;
+ i2s->bitspersample = I2S_BITS_PER_SAMPLE;
+ i2s->channels = I2S_CHANNELS;
+ i2s->rfs = I2S_RFS;
+ i2s->bfs = I2S_BFS;
+#endif
return 0;
}
/*
- * Gets fdt values for codec config parameters
+ * Init codec
*
- * @param pcodec_info codec information structure
- * @param blob FDT blob
- * @return int value, 0 for success
+ * @param blob FDT blob
+ * @param pi2s_tx i2s parameters required by codec
+ * @return int value, 0 for success
*/
-static int get_sound_codec_values(struct sound_codec_info *pcodec_info)
+static int codec_init(const void *blob, struct i2stx_info *pi2s_tx)
{
- int error = 0;
+ int ret;
const char *codectype;
+#ifdef CONFIG_OF_CONTROL
+ int node;
- codectype = AUDIO_CODEC;
+ /* Get the node from FDT for sound */
+ node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SOUND);
+ if (node <= 0) {
+ debug("EXYNOS_SOUND: No node for sound in device tree\n");
+ debug("node = %d\n", node);
+ return -1;
+ }
+ /*
+ * Get the pre-defined sound codec specific values from FDT.
+ * All of these are expected to be correct otherwise sound
+ * can not be played
+ */
+ codectype = fdt_getprop(blob, node, "samsung,codec-type", NULL);
+ debug("device = %s\n", codectype);
+#else
+ codectype = AUDIO_CODEC;
+#endif
if (!strcmp(codectype, "wm8994")) {
- pcodec_info->codec_type = CODEC_WM_8994;
- error = get_sound_wm8994_values(pcodec_info);
+ /* Check the codec type and initialise the same */
+ ret = wm8994_init(blob, WM8994_AIF2,
+ pi2s_tx->samplingrate,
+ (pi2s_tx->samplingrate * (pi2s_tx->rfs)),
+ pi2s_tx->bitspersample, pi2s_tx->channels);
} else {
- error = -1;
+ debug("%s: Unknown code type %s\n", __func__,
+ codectype);
+ return -1;
}
-
- if (error == -1) {
- debug("fail to get sound codec node properties\n");
+ if (ret) {
+ debug("%s: Codec init failed\n", __func__);
return -1;
}
return 0;
}
-int sound_init(void)
+int sound_init(const void *blob)
{
int ret;
struct i2stx_info *pi2s_tx = &g_i2stx_pri;
- struct sound_codec_info *pcodec_info = &g_codec_info;
/* Get the I2S Values */
- get_sound_i2s_values(pi2s_tx);
+ if (get_sound_i2s_values(pi2s_tx, blob) < 0) {
+ debug(" FDT I2S values failed\n");
+ return -1;
+ }
- /* Get the codec Values */
- if (get_sound_codec_values(pcodec_info) < 0)
+ if (codec_init(blob, pi2s_tx) < 0) {
+ debug(" Codec init failed\n");
return -1;
+ }
ret = i2s_tx_init(pi2s_tx);
if (ret) {
return ret;
}
- /* Check the codec type and initialise the same */
- if (pcodec_info->codec_type == CODEC_WM_8994) {
- ret = wm8994_init(pcodec_info, WM8994_AIF2,
- pi2s_tx->samplingrate,
- (pi2s_tx->samplingrate * (pi2s_tx->rfs)),
- pi2s_tx->bitspersample, pi2s_tx->channels);
- } else {
- debug("%s: Unknown code type %d\n", __func__,
- pcodec_info->codec_type);
- return -1;
- }
- if (ret) {
- debug("%s: Codec init failed\n", __func__);
- return -1;
- }
return ret;
}
#include <asm/io.h>
#include <common.h>
#include <div64.h>
+#include <fdtdec.h>
#include <i2c.h>
#include <i2s.h>
#include <sound.h>
+#include <asm/arch/sound.h>
#include "wm8994.h"
#include "wm8994_registers.h"
static struct wm8994_priv g_wm8994_info;
static unsigned char g_wm8994_i2c_dev_addr;
+static struct sound_codec_info g_codec_info;
/*
* Initialise I2C for wm 8994
return -1;
}
+/*
+ * Gets fdt values for wm8994 config parameters
+ *
+ * @param pcodec_info codec information structure
+ * @param blob FDT blob
+ * @return int value, 0 for success
+ */
+static int get_codec_values(struct sound_codec_info *pcodec_info,
+ const void *blob)
+{
+ int error = 0;
+#ifdef CONFIG_OF_CONTROL
+ enum fdt_compat_id compat;
+ int node;
+ int parent;
+
+ /* Get the node from FDT for codec */
+ node = fdtdec_next_compatible(blob, 0, COMPAT_WOLFSON_WM8994_CODEC);
+ if (node <= 0) {
+ debug("EXYNOS_SOUND: No node for codec in device tree\n");
+ debug("node = %d\n", node);
+ return -1;
+ }
+
+ parent = fdt_parent_offset(blob, node);
+ if (parent < 0) {
+ debug("%s: Cannot find node parent\n", __func__);
+ return -1;
+ }
+
+ compat = fdtdec_lookup(blob, parent);
+ switch (compat) {
+ case COMPAT_SAMSUNG_S3C2440_I2C:
+ pcodec_info->i2c_bus = i2c_get_bus_num_fdt(parent);
+ error |= pcodec_info->i2c_bus;
+ debug("i2c bus = %d\n", pcodec_info->i2c_bus);
+ pcodec_info->i2c_dev_addr = fdtdec_get_int(blob, node,
+ "reg", 0);
+ error |= pcodec_info->i2c_dev_addr;
+ debug("i2c dev addr = %d\n", pcodec_info->i2c_dev_addr);
+ break;
+ default:
+ debug("%s: Unknown compat id %d\n", __func__, compat);
+ return -1;
+ }
+#else
+ pcodec_info->i2c_bus = AUDIO_I2C_BUS;
+ pcodec_info->i2c_dev_addr = AUDIO_I2C_REG;
+ debug("i2c dev addr = %d\n", pcodec_info->i2c_dev_addr);
+#endif
+
+ pcodec_info->codec_type = CODEC_WM_8994;
+
+ if (error == -1) {
+ debug("fail to get wm8994 codec node properties\n");
+ return -1;
+ }
+
+ return 0;
+}
+
/*wm8994 Device Initialisation */
-int wm8994_init(struct sound_codec_info *pcodec_info,
- enum en_audio_interface aif_id,
+int wm8994_init(const void *blob, enum en_audio_interface aif_id,
int sampling_rate, int mclk_freq,
int bits_per_sample, unsigned int channels)
{
int ret = 0;
+ struct sound_codec_info *pcodec_info = &g_codec_info;
+
+ /* Get the codec Values */
+ if (get_codec_values(pcodec_info, blob) < 0) {
+ debug("FDT Codec values failed\n");
+ return -1;
+ }
/* shift the device address by 1 for 7 bit addressing */
g_wm8994_i2c_dev_addr = pcodec_info->i2c_dev_addr;
/*
* intialise wm8994 sound codec device for the given configuration
*
- * @param pcodec_info pointer value of the sound codec info structure
- * parsed from device tree
+ * @param blob FDT node for codec values
* @param aif_id enum value of codec interface port in which
* soc i2s is connected
* @param sampling_rate Sampling rate ranges between from 8khz to 96khz
*
* @returns -1 for error and 0 Success.
*/
-int wm8994_init(struct sound_codec_info *pcodec_info,
- enum en_audio_interface aif_id,
+int wm8994_init(const void *blob, enum en_audio_interface aif_id,
int sampling_rate, int mclk_freq,
int bits_per_sample, unsigned int channels);
#endif /*__WM8994_H__ */
as->slave.cs = cs;
as->regs = regs;
as->mr = ATMEL_SPI_MR_MSTR | ATMEL_SPI_MR_MODFDIS
-#if defined(CONFIG_AT91SAM9X5)
+#if defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9M10G45)
| ATMEL_SPI_MR_WDRBT
#endif
| ATMEL_SPI_MR_PCS(~(1 << cs) & 0xf);
#include <common.h>
#include <malloc.h>
#include <spi.h>
+#include <fdtdec.h>
#include <asm/arch/clk.h>
#include <asm/arch/clock.h>
#include <asm/arch/cpu.h>
#include <asm/arch-exynos/spi.h>
#include <asm/io.h>
+DECLARE_GLOBAL_DATA_PTR;
+
/* Information about each SPI controller */
struct spi_bus {
enum periph_id periph_id;
s32 frequency; /* Default clock frequency, -1 for none */
struct exynos_spi *regs;
int inited; /* 1 if this bus is ready for use */
+ int node;
};
/* A list of spi buses that we know about */
static struct spi_bus spi_bus[EXYNOS5_SPI_NUM_CONTROLLERS];
+static unsigned int bus_count;
struct exynos_spi_slave {
struct spi_slave slave;
static struct spi_bus *spi_get_bus(unsigned dev_index)
{
- if (dev_index < EXYNOS5_SPI_NUM_CONTROLLERS)
+ if (dev_index < bus_count)
return &spi_bus[dev_index];
debug("%s: invalid bus %d", __func__, dev_index);
(dev_index - 3);
}
+/*
+ * Read the SPI config from the device tree node.
+ *
+ * @param blob FDT blob to read from
+ * @param node Node offset to read from
+ * @param bus SPI bus structure to fill with information
+ * @return 0 if ok, or -FDT_ERR_NOTFOUND if something was missing
+ */
+static int spi_get_config(const void *blob, int node, struct spi_bus *bus)
+{
+ bus->node = node;
+ bus->regs = (struct exynos_spi *)fdtdec_get_addr(blob, node, "reg");
+ bus->periph_id = pinmux_decode_periph_id(blob, node);
+
+ if (bus->periph_id == PERIPH_ID_NONE) {
+ debug("%s: Invalid peripheral ID %d\n", __func__,
+ bus->periph_id);
+ return -FDT_ERR_NOTFOUND;
+ }
+
+ /* Use 500KHz as a suitable default */
+ bus->frequency = fdtdec_get_int(blob, node, "spi-max-frequency",
+ 500000);
+
+ return 0;
+}
+
+/*
+ * Process a list of nodes, adding them to our list of SPI ports.
+ *
+ * @param blob fdt blob
+ * @param node_list list of nodes to process (any <=0 are ignored)
+ * @param count number of nodes to process
+ * @param is_dvc 1 if these are DVC ports, 0 if standard I2C
+ * @return 0 if ok, -1 on error
+ */
+static int process_nodes(const void *blob, int node_list[], int count)
+{
+ int i;
+
+ /* build the i2c_controllers[] for each controller */
+ for (i = 0; i < count; i++) {
+ int node = node_list[i];
+ struct spi_bus *bus;
+
+ if (node <= 0)
+ continue;
+
+ bus = &spi_bus[i];
+ if (spi_get_config(blob, node, bus)) {
+ printf("exynos spi_init: failed to decode bus %d\n",
+ i);
+ return -1;
+ }
+
+ debug("spi: controller bus %d at %p, periph_id %d\n",
+ i, bus->regs, bus->periph_id);
+ bus->inited = 1;
+ bus_count++;
+ }
+
+ return 0;
+}
+
/* Sadly there is no error return from this function */
void spi_init(void)
{
- int i;
+ int count;
+
+#ifdef CONFIG_OF_CONTROL
+ int node_list[EXYNOS5_SPI_NUM_CONTROLLERS];
+ const void *blob = gd->fdt_blob;
+
+ count = fdtdec_find_aliases_for_id(blob, "spi",
+ COMPAT_SAMSUNG_EXYNOS_SPI, node_list,
+ EXYNOS5_SPI_NUM_CONTROLLERS);
+ if (process_nodes(blob, node_list, count))
+ return;
+
+#else
struct spi_bus *bus;
- for (i = 0; i < EXYNOS5_SPI_NUM_CONTROLLERS; i++) {
- bus = &spi_bus[i];
- bus->regs = get_spi_base(i);
- bus->periph_id = PERIPH_ID_SPI0 + i;
+ for (count = 0; count < EXYNOS5_SPI_NUM_CONTROLLERS; count++) {
+ bus = &spi_bus[count];
+ bus->regs = get_spi_base(count);
+ bus->periph_id = PERIPH_ID_SPI0 + count;
/* Although Exynos5 supports upto 50Mhz speed,
* we are setting it to 10Mhz for safe side
*/
bus->frequency = 10000000;
bus->inited = 1;
+ bus->node = 0;
+ bus_count = EXYNOS5_SPI_NUM_CONTROLLERS;
}
+#endif
}
{
struct spi_slave *slave;
u32 data;
- u32 kwspi_mpp_config[] = { 0, 0 };
+ static const u32 kwspi_mpp_config[2][2] = {
+ { MPP0_SPI_SCn, 0 }, /* if cs == 0 */
+ { MPP7_SPI_SCn, 0 } /* if cs != 0 */
+ };
if (!spi_cs_is_valid(bus, cs))
return NULL;
writel(KWSPI_IRQMASK, &spireg->irq_mask);
/* program mpp registers to select SPI_CSn */
- if (cs) {
- kwspi_mpp_config[0] = MPP7_SPI_SCn;
- } else {
- kwspi_mpp_config[0] = MPP0_SPI_SCn;
- }
- kirkwood_mpp_conf(kwspi_mpp_config, cs_spi_mpp_back);
+ kirkwood_mpp_conf(kwspi_mpp_config[cs ? 1 : 0], cs_spi_mpp_back);
return slave;
}
static struct usb_string g_dnl_string_defs[] = {
{ 0, manufacturer, },
{ 1, product, },
+ { } /* end of list */
};
static struct usb_gadget_strings g_dnl_string_tab = {
static int g_dnl_unbind(struct usb_composite_dev *cdev)
{
- debug("%s\n", __func__);
+ struct usb_gadget *gadget = cdev->gadget;
+
+ debug("%s: calling usb_gadget_disconnect for "
+ "controller '%s'\n", shortname, gadget->name);
+ usb_gadget_disconnect(gadget);
+
return 0;
}
device_desc.bcdDevice = __constant_cpu_to_le16(0x9999);
}
+ debug("%s: calling usb_gadget_connect for "
+ "controller '%s'\n", shortname, gadget->name);
+ usb_gadget_connect(gadget);
+
return 0;
error:
#include <asm/io.h>
#include <asm/arch/pxa.h>
-#include <usbdescriptors.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <usb/lin_gadget_compat.h>
*/
#include <common.h>
+#include <fdtdec.h>
+#include <libfdt.h>
+#include <malloc.h>
#include <usb.h>
#include <asm/arch/cpu.h>
#include <asm/arch/ehci.h>
#include <asm/arch/system.h>
#include <asm/arch/power.h>
+#include <asm-generic/errno.h>
+#include <linux/compat.h>
#include "ehci.h"
+/* Declare global data pointer */
+DECLARE_GLOBAL_DATA_PTR;
+
+/**
+ * Contains pointers to register base addresses
+ * for the usb controller.
+ */
+struct exynos_ehci {
+ struct exynos_usb_phy *usb;
+ unsigned int *hcd;
+};
+
+static int exynos_usb_parse_dt(const void *blob, struct exynos_ehci *exynos)
+{
+ unsigned int node;
+ int depth;
+
+ node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS_EHCI);
+ if (node <= 0) {
+ debug("EHCI: Can't get device node for ehci\n");
+ return -ENODEV;
+ }
+
+ /*
+ * Get the base address for EHCI controller from the device node
+ */
+ exynos->hcd = (unsigned int *)fdtdec_get_addr(blob, node, "reg");
+ if (exynos->hcd == NULL) {
+ debug("Can't get the EHCI register address\n");
+ return -ENXIO;
+ }
+
+ depth = 0;
+ node = fdtdec_next_compatible_subnode(blob, node,
+ COMPAT_SAMSUNG_EXYNOS_USB_PHY, &depth);
+ if (node <= 0) {
+ debug("EHCI: Can't get device node for usb-phy controller\n");
+ return -ENODEV;
+ }
+
+ /*
+ * Get the base address for usbphy from the device node
+ */
+ exynos->usb = (struct exynos_usb_phy *)fdtdec_get_addr(blob, node,
+ "reg");
+ if (exynos->usb == NULL) {
+ debug("Can't get the usbphy register address\n");
+ return -ENXIO;
+ }
+
+ return 0;
+}
+
/* Setup the EHCI host controller. */
static void setup_usb_phy(struct exynos_usb_phy *usb)
{
*/
int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
- struct exynos_usb_phy *usb;
+ struct exynos_ehci *exynos = NULL;
+
+ exynos = (struct exynos_ehci *)
+ kzalloc(sizeof(struct exynos_ehci), GFP_KERNEL);
+ if (!exynos) {
+ debug("failed to allocate exynos ehci context\n");
+ return -ENOMEM;
+ }
- usb = (struct exynos_usb_phy *)samsung_get_base_usb_phy();
- setup_usb_phy(usb);
+ exynos_usb_parse_dt(gd->fdt_blob, exynos);
- *hccr = (struct ehci_hccr *)samsung_get_base_usb_ehci();
+ setup_usb_phy(exynos->usb);
+
+ *hccr = (struct ehci_hccr *)(exynos->hcd);
*hcor = (struct ehci_hcor *)((uint32_t) *hccr
+ HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
(uint32_t)*hccr, (uint32_t)*hcor,
(uint32_t)HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+ kfree(exynos);
+
return 0;
}
*/
int ehci_hcd_stop(int index)
{
- struct exynos_usb_phy *usb;
+ struct exynos_ehci *exynos = NULL;
+
+ exynos = (struct exynos_ehci *)
+ kzalloc(sizeof(struct exynos_ehci), GFP_KERNEL);
+ if (!exynos) {
+ debug("failed to allocate exynos ehci context\n");
+ return -ENOMEM;
+ }
+
+ exynos_usb_parse_dt(gd->fdt_blob, exynos);
+
+ reset_usb_phy(exynos->usb);
- usb = (struct exynos_usb_phy *)samsung_get_base_usb_phy();
- reset_usb_phy(usb);
+ kfree(exynos);
return 0;
}
writel(get_pllb_init(), &pmc->pllbr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKB) != AT91_PMC_LOCKB)
;
-#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
+#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
+ defined(CONFIG_AT91SAM9X5)
/* Enable UPLL */
writel(readl(&pmc->uckr) | AT91_PMC_UPLLEN | AT91_PMC_BIASEN,
&pmc->uckr);
writel(0, &pmc->pllbr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKB) != 0)
;
-#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
+#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
+ defined(CONFIG_AT91SAM9X5)
/* Disable UPLL */
writel(readl(&pmc->uckr) & (~AT91_PMC_UPLLEN), &pmc->uckr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKU) == AT91_PMC_LOCKU)
{
unsigned int ret;
struct edp_device_info *edp_info;
- struct edp_disp_info disp_info;
edp_info = kzalloc(sizeof(struct edp_device_info), GFP_KERNEL);
if (!edp_info) {
debug("failed to get edp_info data.\n");
return -EFAULT;
}
- disp_info = edp_info->disp_info;
exynos_dp_disp_info(&edp_info->disp_info);
static void exynos_lcd_init(vidinfo_t *vid)
{
exynos_fimd_lcd_init(vid);
+
+ /* Enable flushing after LCD writes if requested */
+ lcd_set_flush_dcache(1);
}
+#ifdef CONFIG_CMD_BMP
static void draw_logo(void)
{
int x, y;
addr = panel_info.logo_addr;
bmp_display(addr, x, y);
}
+#endif
static void lcd_panel_on(vidinfo_t *vid)
{
if (panel_info.logo_on) {
memset(lcd_base, 0, panel_width * panel_height *
(NBITS(panel_info.vl_bpix) >> 3));
+#ifdef CONFIG_CMD_BMP
draw_logo();
+#endif
}
lcd_panel_on(&panel_info);
/* DATAPATH is DMA */
cfg |= EXYNOS_WINCON_DATAPATH_DMA;
- /* bpp is 32 */
- cfg |= EXYNOS_WINCON_WSWP_ENABLE;
+ if (pvid->logo_on) /* To get proprietary LOGO */
+ cfg |= EXYNOS_WINCON_WSWP_ENABLE;
+ else /* To get output console on LCD */
+ cfg |= EXYNOS_WINCON_HAWSWP_ENABLE;
/* dma burst is 16 */
cfg |= EXYNOS_WINCON_BURSTLEN_16WORD;
- /* pixel format is unpacked RGB888 */
- cfg |= EXYNOS_WINCON_BPPMODE_24BPP_888;
+ if (pvid->logo_on) /* To get proprietary LOGO */
+ cfg |= EXYNOS_WINCON_BPPMODE_24BPP_888;
+ else /* To get output console on LCD */
+ cfg |= EXYNOS_WINCON_BPPMODE_16BPP_565;
writel(cfg, (unsigned int)&fimd_ctrl->wincon0 +
EXYNOS_WINCON(win_id));
extern char console_buffer[];
/* arch/$(ARCH)/lib/board.c */
-void board_init_f (ulong) __attribute__ ((noreturn));
+void board_init_f(ulong);
void board_init_r (gd_t *, ulong) __attribute__ ((noreturn));
int checkboard (void);
int checkflash (void);
extern u8 _binary_dt_dtb_start[]; /* embedded device tree blob */
int set_cpu_clk_info(void);
+/**
+ * Show the DRAM size in a board-specific way
+ *
+ * This is used by boards to display DRAM information in their own way.
+ *
+ * @param size Size of DRAM (which should be displayed along with other info)
+ */
+void board_show_dram(ulong size);
+
/* common/flash.c */
void flash_perror (int);
#define CONFIG_CMD_LICENSE /* console license display */
#define CONFIG_CMD_LOADB /* loadb */
#define CONFIG_CMD_LOADS /* loads */
+#define CONFIG_CMD_MEMINFO /* meminfo */
#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
#define CONFIG_CMD_MFSL /* FSL support for Microblaze */
#define CONFIG_CMD_MII /* MII support */
#define CONFIG_CMD_NAND
#define CONFIG_CMD_SF
#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_USB
+
+/*
+ * define CONFIG_USB_EHCI to enable USB Hi-Speed (aka 2.0)
+ * NB: in this case, USB 1.1 devices won't be recognized.
+ */
+
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
/* MMC */
#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
-#define CONFIG_CMD_FAT
#define CONFIG_GENERIC_MMC
#define CONFIG_GENERIC_ATMEL_MCI
+#endif
+
+/* FAT */
+#ifdef CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
+/* USB */
+#ifdef CONFIG_CMD_USB
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_ATMEL
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
+#else
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9x5"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3
+#endif
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_STORAGE
+#endif
+
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_BOOTCOMMAND "sf probe 0; " \
"sf read 0x22000000 0x100000 0x300000; " \
"bootm 0x22000000"
+#elif defined(CONFIG_SYS_USE_DATAFLASH)
+/* bootstrap + u-boot + env + linux in data flash */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x4200
+#define CONFIG_ENV_SIZE 0x4200
+#define CONFIG_ENV_SECT_SIZE 0x210
+#define CONFIG_ENV_SPI_MAX_HZ 30000000
+#define CONFIG_BOOTCOMMAND "sf probe 0; " \
+ "sf read 0x22000000 0x84000 0x294000; " \
+ "bootm 0x22000000"
#else /* CONFIG_SYS_USE_MMC */
/* bootstrap + u-boot + env + linux in mmc */
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_DOS_PARTITION
/* USB */
-#define CONFIG_MUSB_UDC
#define CONFIG_USB_OMAP3
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_USB_ULPI
+#define CONFIG_USB_ULPI_VIEWPORT_OMAP
+#define CONFIG_USB_STORAGE
+#define CONFIG_MUSB_UDC
#define CONFIG_TWL4030_USB
+#define CONFIG_CMD_USB
/* USB device configuration */
#define CONFIG_USB_DEVICE
#define CONFIG_CMD_GPIO
#define CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
+#define CONFIG_CMD_IO
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_ITEST
#define CONFIG_CMD_LOADB
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM_BASE0
#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM_SIZE0
-/* If M5282 port is fully implemented the monitor base will be behind
- * the vector table. */
-#if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE)
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400)
-#else
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */
-#endif
-
#define CONFIG_SYS_MONITOR_LEN 0x20000
#define CONFIG_SYS_MALLOC_LEN (256 << 10)
#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
--- /dev/null
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG EXYNOS5250 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_SAMSUNG /* in a SAMSUNG core */
+#define CONFIG_S5P /* S5P Family */
+#define CONFIG_EXYNOS5 /* which is in a Exynos5 Family */
+#define CONFIG_SMDK5250 /* which is in a SMDK5250 */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Enable fdt support for Exynos5250 */
+#define CONFIG_ARCH_DEVICE_TREE exynos5250
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* Keep L2 Cache Disabled */
+#define CONFIG_SYS_DCACHE_OFF
+
+#define CONFIG_SYS_SDRAM_BASE 0x40000000
+#define CONFIG_SYS_TEXT_BASE 0x43E00000
+
+/* input clock of PLL: SMDK5250 has 24MHz input clock */
+#define CONFIG_SYS_CLK_FREQ 24000000
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_EDITING
+
+/* MACH_TYPE_SMDK5250 macro will be removed once added to mach-types */
+#define MACH_TYPE_SMDK5250 3774
+#define CONFIG_MACH_TYPE MACH_TYPE_SMDK5250
+
+/* Power Down Modes */
+#define S5P_CHECK_SLEEP 0x00000BAD
+#define S5P_CHECK_DIDLE 0xBAD00000
+#define S5P_CHECK_LPA 0xABAD0000
+
+/* Offset for inform registers */
+#define INFORM0_OFFSET 0x800
+#define INFORM1_OFFSET 0x804
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20))
+
+/* select serial console configuration */
+#define CONFIG_SERIAL3 /* use SERIAL 3 */
+#define CONFIG_BAUDRATE 115200
+#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000
+
+/* Console configuration */
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define EXYNOS_DEVICE_SETTINGS \
+ "stdin=serial\0" \
+ "stdout=serial,lcd\0" \
+ "stderr=serial,lcd\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ EXYNOS_DEVICE_SETTINGS
+
+#define TZPC_BASE_OFFSET 0x10000
+
+/* SD/MMC configuration */
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC
+#define CONFIG_SDHCI
+#define CONFIG_S5P_SDHCI
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* PWM */
+#define CONFIG_PWM
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Command definition*/
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NET
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+/* USB */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_EXYNOS
+#define CONFIG_USB_STORAGE
+
+/* MMC SPL */
+#define CONFIG_SPL
+#define COPY_BL2_FNPTR_ADDR 0x02020030
+
+/* specific .lds file */
+#define CONFIG_SPL_LDSCRIPT "board/samsung/smdk5250/smdk5250-uboot-spl.lds"
+#define CONFIG_SPL_TEXT_BASE 0x02023400
+#define CONFIG_SPL_MAX_SIZE (14 * 1024)
+
+#define CONFIG_BOOTCOMMAND "mmc read 40007000 451 2000; bootm 40007000"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT "SMDK5250 # "
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0"
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000)
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000)
+
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_RD_LVL
+
+#define CONFIG_NR_DRAM_BANKS 8
+#define SDRAM_BANK_SIZE (256UL << 20UL) /* 256 MB */
+#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE
+#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE
+#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
+#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE
+#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE
+#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE
+#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE
+#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE
+#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE
+#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE
+
+#define CONFIG_SYS_MONITOR_BASE 0x00000000
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+#define CONFIG_IDENT_STRING " for SMDK5250"
+
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_SECURE_BL1_ONLY
+
+/* Secure FW size configuration */
+#ifdef CONFIG_SECURE_BL1_ONLY
+#define CONFIG_SEC_FW_SIZE (8 << 10) /* 8KB */
+#else
+#define CONFIG_SEC_FW_SIZE 0
+#endif
+
+/* Configuration of BL1, BL2, ENV Blocks on mmc */
+#define CONFIG_RES_BLOCK_SIZE (512)
+#define CONFIG_BL1_SIZE (16 << 10) /*16 K reserved for BL1*/
+#define CONFIG_BL2_SIZE (512UL << 10UL) /* 512 KB */
+#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */
+
+#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
+#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
+#define CONFIG_ENV_OFFSET (CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE)
+
+/* U-boot copy size from boot Media to DRAM.*/
+#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512)
+#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512)
+
+#define OM_STAT (0x1f << 1)
+#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058
+#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
+
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_IRAM_STACK 0x02050000
+
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000)
+
+/* I2C */
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_HARD_I2C
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
+#define CONFIG_DRIVER_S3C24X0_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_MAX_I2C_NUM 8
+#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_I2C_EDID
+
+/* PMIC */
+#define CONFIG_PMIC
+#define CONFIG_PMIC_I2C
+#define CONFIG_PMIC_MAX77686
+
+/* SPI */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SPI_FLASH
+
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_EXYNOS_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED 50000000
+#define EXYNOS5_SPI_NUM_CONTROLLERS 5
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_MODE SPI_MODE_0
+#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
+#define CONFIG_ENV_SPI_BUS 1
+#define CONFIG_ENV_SPI_MAX_HZ 50000000
+#endif
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_MAX77686
+
+/* SPI */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SPI_FLASH
+
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_EXYNOS_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED 50000000
+#define EXYNOS5_SPI_NUM_CONTROLLERS 5
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_MODE SPI_MODE_0
+#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
+#define CONFIG_ENV_SPI_BUS 1
+#define CONFIG_ENV_SPI_MAX_HZ 50000000
+#endif
+
+/* Ethernet Controllor Driver */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_BASE 0x5000000
+#define CONFIG_SMC911X_16_BIT
+#define CONFIG_ENV_SROM_BANK 1
+#endif /*CONFIG_CMD_NET*/
+
+/* Enable PXE Support */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_PXE
+#define CONFIG_MENU
+#endif
+
+/* Sound */
+#define CONFIG_CMD_SOUND
+#ifdef CONFIG_CMD_SOUND
+#define CONFIG_SOUND
+#define CONFIG_I2S
+#define CONFIG_SOUND_WM8994
+#endif
+
+/* Enable devicetree support */
+#define CONFIG_OF_LIBFDT
+
+/* SHA hashing */
+#define CONFIG_CMD_HASH
+#define CONFIG_HASH_VERIFY
+#define CONFIG_SHA1
+#define CONFIG_SHA256
+
+/* Display */
+#define CONFIG_LCD
+#ifdef CONFIG_LCD
+#define CONFIG_EXYNOS_FB
+#define CONFIG_EXYNOS_DP
+#define LCD_XRES 2560
+#define LCD_YRES 1600
+#define LCD_BPP LCD_COLOR16
+#endif
+
+#endif /* __CONFIG_H */
#define CONFIG_BOOTARGS "root=/dev/ram0 ro console=ttyS0,115200n8"
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_USB_DEV_PULLUP_GPIO 33
+/* USB VBUS GPIO 3 */
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+
+#define CONFIG_BOOTDELAY 2
+#define CONFIG_BOOTCOMMAND \
+ "setenv downloaded 0 ; while test $downloaded -eq 0 ; do " \
+ "if bootp ; then setenv downloaded 1 ; fi ; done ; " \
+ "source :script ; " \
+ "bootm ; "
+
+#define CONFIG_USB_GADGET_PXA2XX
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_SUBSET
+
+#define CONFIG_USBNET_DEV_ADDR "de:ad:be:ef:00:01"
+#define CONFIG_USBNET_HOST_ADDR "de:ad:be:ef:00:02"
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "stdin=serial\0" \
+ "stdout=serial\0" \
+ "stderr=serial\0"
+
#endif /* __CONFIG_H */
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+/* define to avoid U-Boot to hang while waiting for TEMT */
+#define CONFIG_SYS_NS16550_BROKEN_TEMT
+
/* select serial console configuration */
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
"load=tftpboot ${load_addr_r} ${u-boot}\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
- "stderr=serial\0" \
- "stdin=serial\0" \
- "stdout=serial\0" \
""
#endif /* CONFIG_KM_DEF_ENV */
"config_nc_dhcp=setenv autoload_old ${autoload}; " \
"setenv autoload no " \
"&& bootp " \
- "&& setenv ncip ${serverip} " \
+ "&& setenv ncip " \
"&& setenv autoload ${autoload_old}; " \
"setenv autoload_old\0" \
"standard_env=setenv ipaddr; setenv netmask; setenv serverip; " \
/*
* Size of malloc() pool
*/
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024 * 4) /* 4MiB for malloc() */
/*
* Other required minimal configurations
--- /dev/null
+/*
+ * Configuation settings for the sh7752evb board
+ *
+ * Copyright (C) 2012 Renesas Solutions Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __SH7752EVB_H
+#define __SH7752EVB_H
+
+#undef DEBUG
+#define CONFIG_SH 1
+#define CONFIG_SH4A 1
+#define CONFIG_SH_32BIT 1
+#define CONFIG_CPU_SH7752 1
+#define CONFIG_SH7752EVB 1
+
+#define CONFIG_SYS_TEXT_BASE 0x5ff80000
+#define CONFIG_SYS_LDSCRIPT "board/renesas/sh7752evb/u-boot.lds"
+
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_DFL
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_MD5SUM
+#define CONFIG_MD5
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTARGS "console=ttySC2,115200 root=/dev/nfs ip=dhcp"
+
+#define CONFIG_VERSION_VARIABLE
+#undef CONFIG_SHOW_BOOT_PROGRESS
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+
+/* MEMORY */
+#define SH7752EVB_SDRAM_BASE (0x40000000)
+#define SH7752EVB_SDRAM_SIZE (512 * 1024 * 1024)
+
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_PBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE 512
+#define CONFIG_SYS_BAUDRATE_TABLE { 115200 }
+
+/* SCIF */
+#define CONFIG_SCIF_CONSOLE 1
+#define CONFIG_CONS_SCIF2 1
+#undef CONFIG_SYS_CONSOLE_INFO_QUIET
+#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
+
+#define CONFIG_SYS_MEMTEST_START (SH7752EVB_SDRAM_BASE)
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
+ 480 * 1024 * 1024)
+#undef CONFIG_SYS_ALT_MEMTEST
+#undef CONFIG_SYS_MEMTEST_SCRATCH
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE
+
+#define CONFIG_SYS_SDRAM_BASE (SH7752EVB_SDRAM_BASE)
+#define CONFIG_SYS_SDRAM_SIZE (SH7752EVB_SDRAM_SIZE)
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + \
+ 128 * 1024 * 1024)
+
+#define CONFIG_SYS_MONITOR_BASE 0x00000000
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
+
+/* FLASH */
+#define CONFIG_SYS_NO_FLASH
+
+/* Ether */
+#define CONFIG_SH_ETHER 1
+#define CONFIG_SH_ETHER_USE_PORT 0
+#define CONFIG_SH_ETHER_PHY_ADDR 18
+#define CONFIG_SH_ETHER_CACHE_WRITEBACK 1
+#define CONFIG_SH_ETHER_USE_GETHER 1
+#define CONFIG_PHYLIB
+#define CONFIG_BITBANGMII
+#define CONFIG_BITBANGMII_MULTI
+#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_RGMII
+#define CONFIG_PHY_VITESSE
+
+#define SH7752EVB_ETHERNET_MAC_BASE_SPI 0x00090000
+#define SH7752EVB_SPI_SECTOR_SIZE (64 * 1024)
+#define SH7752EVB_ETHERNET_MAC_BASE SH7752EVB_ETHERNET_MAC_BASE_SPI
+#define SH7752EVB_ETHERNET_MAC_SIZE 17
+#define SH7752EVB_ETHERNET_NUM_CH 2
+#define CONFIG_BOARD_LATE_INIT
+
+/* SPI */
+#define CONFIG_SH_SPI 1
+#define CONFIG_SH_SPI_BASE 0xfe002000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO 1
+#define CONFIG_SPI_FLASH_MACRONIX 1
+
+/* MMCIF */
+#define CONFIG_MMC 1
+#define CONFIG_GENERIC_MMC 1
+#define CONFIG_SH_MMCIF 1
+#define CONFIG_SH_MMCIF_ADDR 0xffcb0000
+#define CONFIG_SH_MMCIF_CLK 48000000
+
+/* ENV setting */
+#define CONFIG_ENV_IS_EMBEDDED
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SECT_SIZE (64 * 1024)
+#define CONFIG_ENV_ADDR (0x00080000)
+#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR)
+#define CONFIG_ENV_OVERWRITE 1
+#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netboot=bootp; bootm\0"
+
+/* Board Clock */
+#define CONFIG_SYS_CLK_FREQ 48000000
+#define CONFIG_SYS_TMU_CLK_DIV 4
+#define CONFIG_SYS_HZ 1000
+#endif /* __SH7752EVB_H */
/*
- * Copyright (C) 2011 Samsung Electronics
+ * Copyright (C) 2012 Samsung Electronics
*
- * Configuration settings for the SAMSUNG SMDK5250 (EXYNOS5250) board.
+ * Configuration settings for the SAMSUNG SMDK5250 board.
*
* See file CREDITS for list of people who contributed to this
* project.
* MA 02111-1307 USA
*/
-#ifndef __CONFIG_H
-#define __CONFIG_H
+#ifndef __CONFIG_SMDK_H
+#define __CONFIG_SMDK_H
-/* High Level Configuration Options */
-#define CONFIG_SAMSUNG /* in a SAMSUNG core */
-#define CONFIG_S5P /* S5P Family */
-#define CONFIG_EXYNOS5 /* which is in a Exynos5 Family */
-#define CONFIG_SMDK5250 /* which is in a SMDK5250 */
+#include <configs/exynos5250-dt.h>
-#include <asm/arch/cpu.h> /* get chip and board defs */
+#undef CONFIG_DEFAULT_DEVICE_TREE
+#define CONFIG_DEFAULT_DEVICE_TREE exynos5250-smdk5250
-#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
-/* Keep L2 Cache Disabled */
-#define CONFIG_SYS_DCACHE_OFF
-
-#define CONFIG_SYS_SDRAM_BASE 0x40000000
-#define CONFIG_SYS_TEXT_BASE 0x43E00000
-
-/* input clock of PLL: SMDK5250 has 24MHz input clock */
-#define CONFIG_SYS_CLK_FREQ 24000000
-
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_EDITING
-
-/* MACH_TYPE_SMDK5250 macro will be removed once added to mach-types */
-#define MACH_TYPE_SMDK5250 3774
-#define CONFIG_MACH_TYPE MACH_TYPE_SMDK5250
-
-/* Power Down Modes */
-#define S5P_CHECK_SLEEP 0x00000BAD
-#define S5P_CHECK_DIDLE 0xBAD00000
-#define S5P_CHECK_LPA 0xABAD0000
-
-/* Offset for inform registers */
-#define INFORM0_OFFSET 0x800
-#define INFORM1_OFFSET 0x804
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20))
-
-/* select serial console configuration */
-#define CONFIG_SERIAL3 /* use SERIAL 3 */
-#define CONFIG_BAUDRATE 115200
-#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000
-
-#define TZPC_BASE_OFFSET 0x10000
-
-/* SD/MMC configuration */
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MMC
-#define CONFIG_SDHCI
-#define CONFIG_S5P_SDHCI
-
-#define CONFIG_BOARD_EARLY_INIT_F
-
-/* PWM */
-#define CONFIG_PWM
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Command definition*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_NET
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-
-/* USB */
-#define CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_EXYNOS
-#define CONFIG_USB_STORAGE
-
-/* MMC SPL */
-#define CONFIG_SPL
-#define COPY_BL2_FNPTR_ADDR 0x02020030
-
-/* specific .lds file */
-#define CONFIG_SPL_LDSCRIPT "board/samsung/smdk5250/smdk5250-uboot-spl.lds"
-#define CONFIG_SPL_TEXT_BASE 0x02023400
-#define CONFIG_SPL_MAX_SIZE (14 * 1024)
-
-#define CONFIG_BOOTCOMMAND "mmc read 40007000 451 2000; bootm 40007000"
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT "SMDK5250 # "
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0"
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-/* memtest works on */
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000)
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000)
-
-#define CONFIG_SYS_HZ 1000
-
-#define CONFIG_RD_LVL
-
-#define CONFIG_NR_DRAM_BANKS 8
-#define SDRAM_BANK_SIZE (256UL << 20UL) /* 256 MB */
-#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE
-#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
-#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE
-#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE
-
-#define CONFIG_SYS_MONITOR_BASE 0x00000000
-
-/* FLASH and environment organization */
-#define CONFIG_SYS_NO_FLASH
-#undef CONFIG_CMD_IMLS
-#define CONFIG_IDENT_STRING " for SMDK5250"
-
-#define CONFIG_SYS_MMC_ENV_DEV 0
-
-#define CONFIG_SECURE_BL1_ONLY
-
-/* Secure FW size configuration */
-#ifdef CONFIG_SECURE_BL1_ONLY
-#define CONFIG_SEC_FW_SIZE (8 << 10) /* 8KB */
-#else
-#define CONFIG_SEC_FW_SIZE 0
-#endif
-
-/* Configuration of BL1, BL2, ENV Blocks on mmc */
-#define CONFIG_RES_BLOCK_SIZE (512)
-#define CONFIG_BL1_SIZE (16 << 10) /*16 K reserved for BL1*/
-#define CONFIG_BL2_SIZE (512UL << 10UL) /* 512 KB */
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */
-
-#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
-#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
-#define CONFIG_ENV_OFFSET (CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE)
-
-/* U-boot copy size from boot Media to DRAM.*/
-#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512)
-#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512)
-
-#define OM_STAT (0x1f << 1)
-#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058
-#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
-
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_IRAM_STACK 0x02050000
-
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000)
-
-/* I2C */
-#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_HARD_I2C
-#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 Kbps */
-#define CONFIG_DRIVER_S3C24X0_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_MAX_I2C_NUM 8
-#define CONFIG_SYS_I2C_SLAVE 0x0
-#define CONFIG_I2C_EDID
-
-/* PMIC */
-#define CONFIG_PMIC
-#define CONFIG_PMIC_I2C
-#define CONFIG_PMIC_MAX77686
-
-/* SPI */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SPI_FLASH
-
-#ifdef CONFIG_SPI_FLASH
-#define CONFIG_EXYNOS_SPI
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_SPI_FLASH_WINBOND
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-#define CONFIG_SF_DEFAULT_SPEED 50000000
-#define EXYNOS5_SPI_NUM_CONTROLLERS 5
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_MODE SPI_MODE_0
-#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-#define CONFIG_ENV_SPI_BUS 1
-#define CONFIG_ENV_SPI_MAX_HZ 50000000
-#endif
-
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_MAX77686
-
-/* SPI */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SPI_FLASH
-
-#ifdef CONFIG_SPI_FLASH
-#define CONFIG_EXYNOS_SPI
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_SPI_FLASH_WINBOND
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-#define CONFIG_SF_DEFAULT_SPEED 50000000
-#define EXYNOS5_SPI_NUM_CONTROLLERS 5
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_MODE SPI_MODE_0
-#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-#define CONFIG_ENV_SPI_BUS 1
-#define CONFIG_ENV_SPI_MAX_HZ 50000000
-#endif
-
-/* Ethernet Controllor Driver */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE 0x5000000
-#define CONFIG_SMC911X_16_BIT
-#define CONFIG_ENV_SROM_BANK 1
-#endif /*CONFIG_CMD_NET*/
-
-/* Enable PXE Support */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_CMD_PXE
-#define CONFIG_MENU
-#endif
-
-/* Sound */
-#define CONFIG_CMD_SOUND
-#ifdef CONFIG_CMD_SOUND
-#define CONFIG_SOUND
-#define CONFIG_I2S
-#define CONFIG_SOUND_WM8994
-#endif
-
-/* Enable devicetree support */
-#define CONFIG_OF_LIBFDT
-
-/* SHA hashing */
-#define CONFIG_CMD_HASH
-#define CONFIG_HASH_VERIFY
-#define CONFIG_SHA1
-#define CONFIG_SHA256
-
-#endif /* __CONFIG_H */
+#endif /* __CONFIG_SMDK_H */
#define CONFIG_SYS_BOOTMAPSZ ((256*1024*1024) - (4*1024))
#define CONFIG_SPL_RAM_DEVICE
-#define CONFIG_SPL_STACK (&__stack_start)
+#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start))
#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start)
#define CONFIG_CMD_MMC
#define CONFIG_CMD_DFU
#define CONFIG_CMD_GPT
+#define CONFIG_CMD_SETEXPR
/* FAT */
#define CONFIG_CMD_FAT
"name="PARTS_UMS",size=-,uuid=${uuid_gpt_"PARTS_UMS"}\0" \
#define CONFIG_DFU_ALT \
- "dfu_alt_info=" \
"u-boot mmc 80 400;" \
- "uImage fat 0 2\0" \
+ "uImage ext4 0 2\0" \
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SYS_CONSOLE_INFO_QUIET
"mmc read 0 0x42100000 0x80 0x200; run updatebackup\0" \
"lpj=lpj=3981312\0" \
"nfsboot=" \
- "set bootargs root=/dev/nfs rw " \
+ "setenv bootargs root=/dev/nfs rw " \
"nfsroot=${nfsroot},nolock,tcp " \
"ip=${ipaddr}:${serverip}:${gatewayip}:" \
"${netmask}:generic:usb0:off " CONFIG_ENV_COMMON_BOOT \
"; run bootk\0" \
"ramfsboot=" \
- "set bootargs root=/dev/ram0 rw rootfstype=ext2 " \
+ "setenv bootargs root=/dev/ram0 rw rootfstype=ext2 " \
"${console} ${meminfo} " \
"initrd=0x43000000,8M ramdisk=8192\0" \
"mmcboot=" \
- "set bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \
+ "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \
"${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo}; " \
"run loaduimage; bootm 0x40007FC0\0" \
- "bootchart=set opts init=/sbin/bootchartd; run bootcmd\0" \
+ "bootchart=setenv opts init=/sbin/bootchartd; run bootcmd\0" \
"boottrace=setenv opts initcall_debug; run bootcmd\0" \
"mmcoops=mmc read 0 0x40000000 0x40 8; md 0x40000000 0x400\0" \
"verify=n\0" \
"meminfo=crashkernel=32M@0x50000000\0" \
"nfsroot=/nfsroot/arm\0" \
"bootblock=" CONFIG_BOOTBLOCK "\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage\0" \
+ "loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage\0" \
"mmcdev=0\0" \
"mmcbootpart=2\0" \
- "mmcrootpart=3\0" \
+ "mmcrootpart=5\0" \
"opts=always_resume=1\0" \
"partitions=" PARTS_DEFAULT \
- CONFIG_DFU_ALT \
+ "dfu_alt_info=" CONFIG_DFU_ALT \
+ "spladdr=0x40000100\0" \
+ "splsize=0x200\0" \
+ "splfile=falcon.bin\0" \
+ "spl_export=" \
+ "setexpr spl_imgsize ${splsize} + 8 ;" \
+ "setexpr spl_imgaddr ${spladdr} - 8 ;" \
+ "setexpr spl_addr_tmp ${spladdr} - 4 ;" \
+ "mw.b ${spl_imgaddr} 0x00 ${spl_imgsize};run loaduimage;" \
+ "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \
+ "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo};" \
+ "spl export atags 0x40007FC0;" \
+ "crc32 ${spladdr} ${splsize} ${spl_imgaddr};" \
+ "mw.l ${spl_addr_tmp} ${splsize};" \
+ "ext4write mmc ${mmcdev}:${mmcbootpart}" \
+ " /${splfile} ${spl_imgaddr} ${spl_imgsize};" \
+ "setenv spl_imgsize;" \
+ "setenv spl_imgaddr;" \
+ "setenv spl_addr_tmp;\0"
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_ENV_OFFSET ((32 - 4) << 10) /* 32KiB - 4KiB */
#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+
+/* EXT4 */
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
+/* Falcon mode definitions */
+#define CONFIG_CMD_SPL
+#define CONFIG_SYS_SPL_ARGS_ADDR PHYS_SDRAM_1 + 0x100
/* GPT */
#define CONFIG_EFI_PARTITION
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_CACHELINE_SIZE 32
-
#define CONFIG_SOFT_I2C
#define CONFIG_SOFT_I2C_READ_REPEATED_START
#define CONFIG_SYS_I2C_INIT_BOARD
--- /dev/null
+/*
+ * Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net>
+ *
+ * Based on the netspace_v2 code which is
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CONFIG_WIRELESS_SPACE_H
+#define _CONFIG_WIRELESS_SPACE_H
+
+/*
+ * Machine number definition
+ */
+#define MACH_TYPE_WIRELESS_SPACE 2500 /* is missing in mach-types.h */
+#define CONFIG_MACH_TYPE MACH_TYPE_WIRELESS_SPACE
+#define CONFIG_IDENT_STRING " Wireless Space"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD /* SoC Family Name */
+/* SoC name */
+#define CONFIG_KW88F6281
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* no NOR or SPI flash */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_USB
+
+/*
+ * Core clock definition
+ */
+#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
+
+/*
+ * SDRAM configuration
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+
+/*
+ * Different SDRAM configuration and size for some of the boards derived
+ * from the Network Space v2
+ */
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/* Remove or override few declarations from mv-common.h */
+#undef CONFIG_RBTREE
+#undef CONFIG_SYS_IDE_MAXBUS
+#undef CONFIG_SYS_IDE_MAXDEVICE
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE 1
+#undef CONFIG_SYS_PROMPT
+#define CONFIG_SYS_PROMPT "ws> "
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable only egiga0... */
+#define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */
+#define CONFIG_PHY_BASE_ADR 0xa /* ... through a 'fake' PHY */
+#define CONFIG_MII
+#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#define CONFIG_NETCONSOLE
+#define CONFIG_MV88E61XX_SWITCH
+#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
+#define CONFIG_MV88E61XX_CMD
+#define CONFIG_CMD_TFTPPUT
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * SATA Driver configuration
+ */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#endif /* CONFIG_MVSATA_IDE */
+
+/*
+ * Enable GPI0 support
+ */
+#define CONFIG_KIRKWOOD_GPIO
+
+/*
+ * Enable I2C support
+ */
+#ifdef CONFIG_CMD_I2C
+/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
+#endif /* CONFIG_CMD_I2C */
+
+/*
+ * Partition support
+ */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+
+/*
+ * File systems support
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Console configuration
+ */
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+/*
+ * Enable device tree support
+ */
+#define CONFIG_OF_LIBFDT
+
+/*
+ * Environment variables configurations
+ */
+
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128KB */
+#define CONFIG_ENV_SIZE 0x20000 /* 128KB */
+#define CONFIG_ENV_OFFSET 0x80000 /* env starts here */
+
+/*
+ * Board-specific command to make using buttons etc easier
+ */
+
+#define CONFIG_WIRELESS_SPACE_CMD
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_PREBOOT
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200"
+
+#define CONFIG_BOOTCOMMAND \
+ "if run usbload || run diskload; then bootm; fi"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "stdin=serial\0" \
+ "stdout=serial\0" \
+ "stderr=serial\0" \
+ "bootfile=uImage\0" \
+ "loadaddr=0x800000\0" \
+ "autoload=no\0" \
+ "netconsole=" \
+ "set stdin $stdin,nc; " \
+ "set stdout $stdout,nc; " \
+ "set stderr $stderr,nc;\0" \
+ "diskload=ide reset && " \
+ "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
+ "usbload=usb start && " \
+ "fatload usb 0:1 $loadaddr /boot/$bootfile\0" \
+ "preboot=" \
+ "dhcp && run netconsole\0"
+
+#endif /* _CONFIG_WIRELESS_SPACE_H */
* when associated through the ".callbacks" environment variable, the callback
* will be executed any time the variable is inserted, overwritten, or deleted.
*/
+#ifdef CONFIG_SPL_BUILD
+#define U_BOOT_ENV_CALLBACK(name, callback) \
+ static inline void _u_boot_env_noop_##name(void) \
+ { \
+ (void)callback; \
+ }
+#else
#define U_BOOT_ENV_CALLBACK(name, callback) \
ll_entry_declare(struct env_clbk_tbl, name, env_clbk, env_clbk) = \
{#name, callback}
+#endif
#endif /* __ENV_CALLBACK_H__ */
COMPAT_NVIDIA_TEGRA20_NAND, /* Tegra2 NAND controller */
COMPAT_NVIDIA_TEGRA20_PWM, /* Tegra 2 PWM controller */
COMPAT_NVIDIA_TEGRA20_DC, /* Tegra 2 Display controller */
+ COMPAT_SMSC_LAN9215, /* SMSC 10/100 Ethernet LAN9215 */
+ COMPAT_SAMSUNG_EXYNOS5_SROMC, /* Exynos5 SROMC */
+ COMPAT_SAMSUNG_S3C2440_I2C, /* Exynos I2C Controller */
+ COMPAT_SAMSUNG_EXYNOS5_SOUND, /* Exynos Sound */
+ COMPAT_WOLFSON_WM8994_CODEC, /* Wolfson WM8994 Sound Codec */
+ COMPAT_SAMSUNG_EXYNOS_SPI, /* Exynos SPI */
+ COMPAT_SAMSUNG_EXYNOS_EHCI, /* Exynos EHCI controller */
+ COMPAT_SAMSUNG_EXYNOS_USB_PHY, /* Exynos phy controller for usb2.0 */
+ COMPAT_MAXIM_MAX77686_PMIC, /* MAX77686 PMIC */
COMPAT_COUNT,
};
ulong buffer_write_tout; /* maximum buffer write timeout */
ushort vendor; /* the primary vendor id */
ushort cmd_reset; /* vendor specific reset command */
+ uchar cmd_erase_sector; /* vendor specific erase sect. command */
ushort interface; /* used for x8/x16 adjustments */
ushort legacy_unlock; /* support Intel legacy (un)locking */
ushort manufacturer_id; /* manufacturer id */
extern int get_multi_sda_pin(void);
extern int multi_i2c_init(void);
#endif
+
+/**
+ * Get FDT values for i2c bus.
+ *
+ * @param blob Device tree blbo
+ * @return the number of I2C bus
+ */
+void board_i2c_init(const void *blob);
+
+/**
+ * Find the I2C bus number by given a FDT I2C node.
+ *
+ * @param blob Device tree blbo
+ * @param node FDT I2C node to find
+ * @return the number of I2C bus (zero based), or -1 on error
+ */
+int i2c_get_bus_num_fdt(int node);
+
+/**
+ * Reset the I2C bus represented by the given a FDT I2C node.
+ *
+ * @param blob Device tree blbo
+ * @param node FDT I2C node to find
+ * @return 0 if port was reset, -1 if not found
+ */
+int i2c_reset_port_fdt(const void *blob, int node);
#endif /* _I2C_H_ */
* the stuct and enums here are used to specify switch configuration params
*/
#if defined(CONFIG_MV88E61XX_SWITCH)
-enum mv88e61xx_cfg_vlan {
- MV88E61XX_VLANCFG_DEFAULT,
- MV88E61XX_VLANCFG_ROUTER
-};
+
+/* constants for any 88E61xx switch */
+#define MV88E61XX_MAX_PORTS_NUM 6
enum mv88e61xx_cfg_mdip {
MV88E61XX_MDIP_NOCHANGE,
struct mv88e61xx_config {
char *name;
- enum mv88e61xx_cfg_vlan vlancfg;
+ u8 vlancfg[MV88E61XX_MAX_PORTS_NUM];
enum mv88e61xx_cfg_rgmiid rgmii_delay;
enum mv88e61xx_cfg_prtstt portstate;
enum mv88e61xx_cfg_ledinit led_init;
u8 cpuport;
};
+/*
+ * Common mappings for Internal VLANs
+ * These mappings consider that all ports are useable; the driver
+ * will mask inexistent/unused ports.
+ */
+
+/* Switch mode : routes any port to any port */
+#define MV88E61XX_VLANCFG_SWITCH { 0x3F, 0x3F, 0x3F, 0x3F, 0x3F, 0x3F }
+
+/* Router mode: routes only CPU port 5 to/from non-CPU ports 0-4 */
+#define MV88E61XX_VLANCFG_ROUTER { 0x20, 0x20, 0x20, 0x20, 0x20, 0x1F }
+
int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig);
#endif /* CONFIG_MV88E61XX_SWITCH */
/*
* Initialises audio sub system
- *
+ * @param blob Pointer of device tree node or NULL if none.
* @return int value 0 for success, -1 for error
*/
-int sound_init(void);
+int sound_init(const void *blob);
/*
* plays the pcm data buffer in pcm_data.h through i2s1 to make the
#define TWL4030_USB_PHY_CLK_CTRL 0xFE
#define TWL4030_USB_PHY_CLK_CTRL_STS 0xFF
+/* GPIO */
+#define TWL4030_GPIO_GPIODATAIN1 0x00
+#define TWL4030_GPIO_GPIODATAIN2 0x01
+#define TWL4030_GPIO_GPIODATAIN3 0x02
+#define TWL4030_GPIO_GPIODATADIR1 0x03
+#define TWL4030_GPIO_GPIODATADIR2 0x04
+#define TWL4030_GPIO_GPIODATADIR3 0x05
+#define TWL4030_GPIO_GPIODATAOUT1 0x06
+#define TWL4030_GPIO_GPIODATAOUT2 0x07
+#define TWL4030_GPIO_GPIODATAOUT3 0x08
+#define TWL4030_GPIO_CLEARGPIODATAOUT1 0x09
+#define TWL4030_GPIO_CLEARGPIODATAOUT2 0x0A
+#define TWL4030_GPIO_CLEARGPIODATAOUT3 0x0B
+#define TWL4030_GPIO_SETGPIODATAOUT1 0x0C
+#define TWL4030_GPIO_SETGPIODATAOUT2 0x0D
+#define TWL4030_GPIO_SETGPIODATAOUT3 0x0E
+#define TWL4030_GPIO_GPIO_DEBEN1 0x0F
+#define TWL4030_GPIO_GPIO_DEBEN2 0x10
+#define TWL4030_GPIO_GPIO_DEBEN3 0x11
+#define TWL4030_GPIO_GPIO_CTRL 0x12
+#define TWL4030_GPIO_GPIOPUPDCTR1 0x13
+#define TWL4030_GPIO_GPIOPUPDCTR2 0x14
+#define TWL4030_GPIO_GPIOPUPDCTR3 0x15
+#define TWL4030_GPIO_GPIOPUPDCTR4 0x16
+#define TWL4030_GPIO_GPIOPUPDCTR5 0x17
+#define TWL4030_GPIO_GPIO_ISR1A 0x19
+#define TWL4030_GPIO_GPIO_ISR2A 0x1A
+#define TWL4030_GPIO_GPIO_ISR3A 0x1B
+#define TWL4030_GPIO_GPIO_IMR1A 0x1C
+#define TWL4030_GPIO_GPIO_IMR2A 0x1D
+#define TWL4030_GPIO_GPIO_IMR3A 0x1E
+#define TWL4030_GPIO_GPIO_ISR1B 0x1F
+#define TWL4030_GPIO_GPIO_ISR2B 0x20
+#define TWL4030_GPIO_GPIO_ISR3B 0x21
+#define TWL4030_GPIO_GPIO_IMR1B 0x22
+#define TWL4030_GPIO_GPIO_IMR2B 0x23
+#define TWL4030_GPIO_GPIO_IMR3B 0x24
+#define TWL4030_GPIO_GPIO_EDR1 0x28
+#define TWL4030_GPIO_GPIO_EDR2 0x29
+#define TWL4030_GPIO_GPIO_EDR3 0x2A
+#define TWL4030_GPIO_GPIO_EDR4 0x2B
+#define TWL4030_GPIO_GPIO_EDR5 0x2C
+#define TWL4030_GPIO_GPIO_SIH_CTRL 0x2D
+
/*
* Convience functions to read and write from TWL4030
*
struct usb_device *usb_alloc_new_device(void *controller);
int usb_new_device(struct usb_device *dev);
+void usb_free_device(void);
#endif /*_USB_H_ */
DEFINE(GENERATED_BD_INFO_SIZE,
(sizeof(struct bd_info) + 15) & ~15);
+ DEFINE(GD_SIZE, sizeof(struct global_data));
+
+ DEFINE(GD_BD, offsetof(struct global_data, bd));
+
+#if defined(CONFIG_ARM)
+
+ DEFINE(GD_RELOCADDR, offsetof(struct global_data, relocaddr));
+
+ DEFINE(GD_RELOC_OFF, offsetof(struct global_data, reloc_off));
+
+ DEFINE(GD_START_ADDR_SP, offsetof(struct global_data, start_addr_sp));
+
+#endif
+
return 0;
}
COMPAT(NVIDIA_TEGRA20_NAND, "nvidia,tegra20-nand"),
COMPAT(NVIDIA_TEGRA20_PWM, "nvidia,tegra20-pwm"),
COMPAT(NVIDIA_TEGRA20_DC, "nvidia,tegra20-dc"),
+ COMPAT(SMSC_LAN9215, "smsc,lan9215"),
+ COMPAT(SAMSUNG_EXYNOS5_SROMC, "samsung,exynos-sromc"),
+ COMPAT(SAMSUNG_S3C2440_I2C, "samsung,s3c2440-i2c"),
+ COMPAT(SAMSUNG_EXYNOS5_SOUND, "samsung,exynos-sound"),
+ COMPAT(WOLFSON_WM8994_CODEC, "wolfson,wm8994-codec"),
+ COMPAT(SAMSUNG_EXYNOS_SPI, "samsung,exynos-spi"),
+ COMPAT(SAMSUNG_EXYNOS_EHCI, "samsung,exynos-ehci"),
+ COMPAT(SAMSUNG_EXYNOS_USB_PHY, "samsung,exynos-usb-phy"),
+ COMPAT(MAXIM_MAX77686_PMIC, "maxim,max77686_pmic"),
};
const char *fdtdec_get_compatible(enum fdt_compat_id id)
AFLAGS += -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL
CFLAGS += -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL
-SOBJS = start.o lowlevel_init.o
+SOBJS = start.o crt0.o lowlevel_init.o
COBJS = nand_boot_fsl_nfc.o
SRCS := $(SRCTREE)/nand_spl/nand_boot_fsl_nfc.c
SRCS += $(SRCTREE)/arch/arm/cpu/arm1136/start.S
+SRCS += $(SRCTREE)/arch/arm/lib/crt0.S
SRCS += $(SRCTREE)/board/freescale/mx31pdk/lowlevel_init.S
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
__OBJS := $(SOBJS) $(COBJS)
$(obj)%.o: $(SRCTREE)/arch/arm/cpu/arm1136/%.S
$(CC) $(AFLAGS) -c -o $@ $<
+$(obj)%.o: $(SRCTREE)/arch/arm/lib/%.S
+ $(CC) $(AFLAGS) -c -o $@ $<
+
$(obj)%.o: $(SRCTREE)/board/freescale/mx31pdk/%.S
$(CC) $(AFLAGS) -c -o $@ $<
AFLAGS += -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL
CFLAGS += -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL
-SOBJS = start.o lowlevel_init.o
+SOBJS = start.o crt0.o lowlevel_init.o
COBJS = nand_boot_fsl_nfc.o
SRCS := $(SRCTREE)/nand_spl/nand_boot_fsl_nfc.c
SRCS += $(SRCTREE)/arch/arm/cpu/arm926ejs/start.S
+SRCS += $(SRCTREE)/arch/arm/lib/crt0.S
SRCS += $(SRCTREE)/board/karo/tx25/lowlevel_init.S
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
__OBJS := $(SOBJS) $(COBJS)
$(obj)%.o: $(SRCTREE)/arch/arm/cpu/arm926ejs/%.S
$(CC) $(AFLAGS) -c -o $@ $<
+$(obj)%.o: $(SRCTREE)/arch/arm/lib/%.S
+ $(CC) $(AFLAGS) -c -o $@ $<
+
$(obj)%.o: $(SRCTREE)/board/karo/tx25/%.S
$(CC) $(AFLAGS) -c -o $@ $<
*/
int fw_setenv(int argc, char *argv[])
{
- int i, len;
+ int i;
+ size_t len;
char *name;
char *value = NULL;
int lockfd = -1;
int retval = EXIT_SUCCESS;
- lockfd = open(lockname, O_WRONLY | O_CREAT | O_TRUNC);
+ lockfd = open(lockname, O_WRONLY | O_CREAT | O_TRUNC, 0666);
if (-1 == lockfd) {
fprintf(stderr, "Error opening lock file %s\n", lockname);
return EXIT_FAILURE;
projects / platform / kernel / u-boot.git / commitdiff