prompt "Target select"
optional
-config TARGET_MPC8323ERDB
- bool "Support MPC8323ERDB"
- select ARCH_MPC832X
-
config TARGET_MPC832XEMDS
bool "Support MPC832XEMDS"
select ARCH_MPC832X
config FSL_ELBC
bool
-source "board/freescale/mpc8323erdb/Kconfig"
source "board/freescale/mpc832xemds/Kconfig"
source "board/freescale/mpc8349emds/Kconfig"
source "board/freescale/mpc837xerdb/Kconfig"
+++ /dev/null
-if TARGET_MPC8323ERDB
-
-config SYS_BOARD
- default "mpc8323erdb"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "MPC8323ERDB"
-
-endif
+++ /dev/null
-MPC8323ERDB BOARD
-#M: Michael Barkowski <michael.barkowski@freescale.com>
-S: Orphan (since 2018-05)
-F: board/freescale/mpc8323erdb/
-F: include/configs/MPC8323ERDB.h
-F: configs/MPC8323ERDB_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y := mpc8323erdb.o
+++ /dev/null
-Freescale MPC8323ERDB Board
------------------------------------------
-
-1. Memory Map
- The memory map looks like this:
-
- 0x0000_0000 0x03ff_ffff DDR 64M
- 0x8000_0000 0x8fff_ffff PCI MEM 256M
- 0x9000_0000 0x9fff_ffff PCI_MMIO 256M
- 0xe000_0000 0xe00f_ffff IMMR 1M
- 0xd000_0000 0xd3ff_ffff PCI IO 64M
- 0xfe00_0000 0xfeff_ffff NOR FLASH (CS0) 16M
-
-2. Compilation
-
- Assuming you're using BASH (or similar) as your shell:
-
- export CROSS_COMPILE=your-cross-compiler-prefix-
- make distclean
- make MPC8323ERDB_config
- make
-
-3. Downloading and Flashing Images
-
-3.1 Reflash U-Boot Image using U-Boot
-
- N.b, have an alternate means of programming
- the flash available if the new U-Boot doesn't boot.
-
- First try a:
-
- tftpboot $loadaddr $uboot
-
- to make sure that the TFTP load will succeed before
- an erase goes ahead and wipes out your current firmware.
- Then do a:
-
- run tftpflash
-
- which is a shorter version of the manual sequence:
-
- tftp $loadaddr u-boot.bin
- protect off fe000000 +$filesize
- erase fe000000 +$filesize
- cp.b $loadaddr fe000000 $filesize
-
- To keep your old U-Boot's environment variables, do a:
-
- saveenv
-
- prior to resetting the board.
-
-3.2 Downloading and Booting Linux Kernel
-
- Ensure that all networking-related environment variables are set
- properly (including ipaddr, serverip, gatewayip (if needed),
- netmask, ethaddr, eth1addr, rootpath (if using NFS root),
- fdtfile, and bootfile).
-
- Then, do one of the following, depending on whether you
- want an NFS root or a ramdisk root:
-
- run nfsboot
-
- or
-
- run ramboot
-
-4 Notes
-
- The console baudrate for MPC8323ERDB is 115200bps.
+++ /dev/null
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- *
- * Michael Barkowski <michael.barkowski@freescale.com>
- * Based on mpc832xmds file by Dave Liu <daveliu@freescale.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- */
-
-#include <common.h>
-#include <eeprom.h>
-#include <env.h>
-#include <fdt_support.h>
-#include <init.h>
-#include <ioports.h>
-#include <mpc83xx.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <command.h>
-#include <asm/global_data.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <u-boot/crc.h>
-#if defined(CONFIG_PCI)
-#include <pci.h>
-#endif
-#include <asm/mmu.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const qe_iop_conf_t qe_iop_conf_tab[] = {
- /* UCC3 */
- {1, 0, 1, 0, 1}, /* TxD0 */
- {1, 1, 1, 0, 1}, /* TxD1 */
- {1, 2, 1, 0, 1}, /* TxD2 */
- {1, 3, 1, 0, 1}, /* TxD3 */
- {1, 9, 1, 0, 1}, /* TxER */
- {1, 12, 1, 0, 1}, /* TxEN */
- {3, 24, 2, 0, 1}, /* TxCLK->CLK10 */
-
- {1, 4, 2, 0, 1}, /* RxD0 */
- {1, 5, 2, 0, 1}, /* RxD1 */
- {1, 6, 2, 0, 1}, /* RxD2 */
- {1, 7, 2, 0, 1}, /* RxD3 */
- {1, 8, 2, 0, 1}, /* RxER */
- {1, 10, 2, 0, 1}, /* RxDV */
- {0, 13, 2, 0, 1}, /* RxCLK->CLK9 */
- {1, 11, 2, 0, 1}, /* COL */
- {1, 13, 2, 0, 1}, /* CRS */
-
- /* UCC2 */
- {0, 18, 1, 0, 1}, /* TxD0 */
- {0, 19, 1, 0, 1}, /* TxD1 */
- {0, 20, 1, 0, 1}, /* TxD2 */
- {0, 21, 1, 0, 1}, /* TxD3 */
- {0, 27, 1, 0, 1}, /* TxER */
- {0, 30, 1, 0, 1}, /* TxEN */
- {3, 23, 2, 0, 1}, /* TxCLK->CLK3 */
-
- {0, 22, 2, 0, 1}, /* RxD0 */
- {0, 23, 2, 0, 1}, /* RxD1 */
- {0, 24, 2, 0, 1}, /* RxD2 */
- {0, 25, 2, 0, 1}, /* RxD3 */
- {0, 26, 1, 0, 1}, /* RxER */
- {0, 28, 2, 0, 1}, /* Rx_DV */
- {3, 21, 2, 0, 1}, /* RxCLK->CLK16 */
- {0, 29, 2, 0, 1}, /* COL */
- {0, 31, 2, 0, 1}, /* CRS */
-
- {3, 4, 3, 0, 2}, /* MDIO */
- {3, 5, 1, 0, 2}, /* MDC */
-
- {0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */
-};
-
-int fixed_sdram(void);
-
-int dram_init(void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msize = 0;
-
- if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
- return -ENXIO;
-
- /* DDR SDRAM - Main SODIMM */
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_SDRAM_BASE & LAWBAR_BAR;
-
- msize = fixed_sdram();
-
- /* set total bus SDRAM size(bytes) -- DDR */
- gd->ram_size = msize * 1024 * 1024;
-
- return 0;
-}
-
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-int fixed_sdram(void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msize = 0;
- u32 ddr_size;
- u32 ddr_size_log2;
-
- msize = CONFIG_SYS_DDR_SIZE;
- for (ddr_size = msize << 20, ddr_size_log2 = 0;
- (ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) {
- if (ddr_size & 1) {
- return -1;
- }
- }
- im->sysconf.ddrlaw[0].ar =
- LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
- im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CNTL;
- im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
- im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
- im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
- im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
- im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
- im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
- im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
- im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
- im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
- im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
- __asm__ __volatile__ ("sync");
- udelay(200);
-
- im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
- __asm__ __volatile__ ("sync");
- return msize;
-}
-
-int checkboard(void)
-{
- puts("Board: Freescale MPC8323ERDB\n");
- return 0;
-}
-
-static struct pci_region pci_regions[] = {
- {
- bus_start: CONFIG_SYS_PCI1_MEM_BASE,
- phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
- size: CONFIG_SYS_PCI1_MEM_SIZE,
- flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
- phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
- size: CONFIG_SYS_PCI1_MMIO_SIZE,
- flags: PCI_REGION_MEM
- },
- {
- bus_start: CONFIG_SYS_PCI1_IO_BASE,
- phys_start: CONFIG_SYS_PCI1_IO_PHYS,
- size: CONFIG_SYS_PCI1_IO_SIZE,
- flags: PCI_REGION_IO
- }
-};
-
-void pci_init_board(void)
-{
- volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
- struct pci_region *reg[] = { pci_regions };
-
- /* Enable all 3 PCI_CLK_OUTPUTs. */
- clk->occr |= 0xe0000000;
-
- /* Configure PCI Local Access Windows */
- pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
-
- pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
-
- mpc83xx_pci_init(1, reg);
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
- ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI
- ft_pci_setup(blob, bd);
-#endif
-
- return 0;
-}
-#endif
-
-#if defined(CONFIG_SYS_I2C_MAC_OFFSET)
-int mac_read_from_eeprom(void)
-{
- uchar buf[28];
- char str[18];
- int i = 0;
- unsigned int crc = 0;
- unsigned char enetvar[32];
-
- /* Read MAC addresses from EEPROM */
- if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_MAC_OFFSET, buf, 28)) {
- printf("\nEEPROM @ 0x%02x read FAILED!!!\n",
- CONFIG_SYS_I2C_EEPROM_ADDR);
- } else {
- uint32_t crc_buf;
-
- memcpy(&crc_buf, &buf[24], sizeof(uint32_t));
-
- if (crc32(crc, buf, 24) == crc_buf) {
- printf("Reading MAC from EEPROM\n");
- for (i = 0; i < 4; i++) {
- if (memcmp(&buf[i * 6], "\0\0\0\0\0\0", 6)) {
- sprintf(str,
- "%02X:%02X:%02X:%02X:%02X:%02X",
- buf[i * 6], buf[i * 6 + 1],
- buf[i * 6 + 2], buf[i * 6 + 3],
- buf[i * 6 + 4], buf[i * 6 + 5]);
- sprintf((char *)enetvar,
- i ? "eth%daddr" : "ethaddr", i);
- env_set((char *)enetvar, str);
- }
- }
- }
- }
- return 0;
-}
-#endif /* CONFIG_I2C_MAC_OFFSET */
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFE000000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=66666667
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_MPC8323ERDB=y
-CONFIG_CORE_PLL_RATIO_25_1=y
-CONFIG_QUICC_MULT_FACTOR_3=y
-CONFIG_PCI_HOST_MODE_ENABLE=y
-CONFIG_PCI_INT_ARBITER1_ENABLE=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="IMMR"
-CONFIG_BAT1_BASE=0xE0000000
-CONFIG_BAT1_LENGTH_4_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_INHIBITED=y
-CONFIG_BAT1_ICACHE_GUARDED=y
-CONFIG_BAT1_DCACHE_INHIBITED=y
-CONFIG_BAT1_DCACHE_GUARDED=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="FLASH"
-CONFIG_BAT2_BASE=0xFE000000
-CONFIG_BAT2_LENGTH_32_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT4=y
-CONFIG_BAT4_NAME="STACK_IN_DCACHE"
-CONFIG_BAT4_BASE=0xE6000000
-CONFIG_BAT4_ACCESS_RW=y
-CONFIG_BAT4_USER_MODE_VALID=y
-CONFIG_BAT4_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="PCI_MEM_PHYS"
-CONFIG_BAT5_BASE=0x80000000
-CONFIG_BAT5_LENGTH_256_MBYTES=y
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT5_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT6=y
-CONFIG_BAT6_NAME="PCI1_MMIO_PHYS"
-CONFIG_BAT6_BASE=0x90000000
-CONFIG_BAT6_LENGTH_256_MBYTES=y
-CONFIG_BAT6_ACCESS_RW=y
-CONFIG_BAT6_ICACHE_INHIBITED=y
-CONFIG_BAT6_ICACHE_GUARDED=y
-CONFIG_BAT6_DCACHE_INHIBITED=y
-CONFIG_BAT6_DCACHE_GUARDED=y
-CONFIG_BAT6_USER_MODE_VALID=y
-CONFIG_BAT6_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFE000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_32_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFE000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_16_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_OR0_EAD_EXTRA=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_OPT_SPEC_READ=y
-CONFIG_LCRR_CLKDIV_2=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=6
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_ADDR=0xFE080000
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_QE=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <linux/stringify.h>
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL 0x00000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-
-#undef CONFIG_SPD_EEPROM
-#if defined(CONFIG_SPD_EEPROM)
-/* Determine DDR configuration from I2C interface
- */
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */
-#else
-/* Manually set up DDR parameters
- */
-#define CONFIG_SYS_DDR_SIZE 64 /* MB */
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ROW_BIT_13 \
- | CSCONFIG_COL_BIT_9)
- /* 0x80010101 */
-#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
- | (0 << TIMING_CFG0_WRT_SHIFT) \
- | (0 << TIMING_CFG0_RRT_SHIFT) \
- | (0 << TIMING_CFG0_WWT_SHIFT) \
- | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
- | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
- /* 0x00220802 */
-#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
- | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
- | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
- | (5 << TIMING_CFG1_CASLAT_SHIFT) \
- | (3 << TIMING_CFG1_REFREC_SHIFT) \
- | (2 << TIMING_CFG1_WRREC_SHIFT) \
- | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
- | (2 << TIMING_CFG1_WRTORD_SHIFT))
- /* 0x26253222 */
-#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
- | (31 << TIMING_CFG2_CPO_SHIFT) \
- | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
- | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
- | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
- | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
- | (7 << TIMING_CFG2_FOUR_ACT_SHIFT))
- /* 0x1f9048c7 */
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
- /* 0x02000000 */
-#define CONFIG_SYS_DDR_MODE ((0x4448 << SDRAM_MODE_ESD_SHIFT) \
- | (0x0232 << SDRAM_MODE_SD_SHIFT))
- /* 0x44480232 */
-#define CONFIG_SYS_DDR_MODE2 0x8000c000
-#define CONFIG_SYS_DDR_INTERVAL ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \
- | (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
- /* 0x03200064 */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x00000003
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
- | SDRAM_CFG_SDRAM_TYPE_DDR2 \
- | SDRAM_CFG_32_BE)
- /* 0x43080000 */
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#endif
-
-/*
- * Memory test
- */
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */
-
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
-
-/*
- * Config on-board EEPROM
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0xd0000000
-#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
-#define CONFIG_SYS_PCI1_IO_SIZE 0x04000000 /* 64M */
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCI_SKIP_HOST_BRIDGE
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-
-#endif /* CONFIG_PCI */
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* ETH3 */
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 4
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-#define CONFIG_UEC_ETH2 /* ETH4 */
-
-#ifdef CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
-#define CONFIG_SYS_UEC2_RX_CLK QE_CLK16
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK3
-#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 0
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
- /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if (CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#define CONFIG_HAS_ETH0 /* add support for "ethaddr" */
-#define CONFIG_HAS_ETH1 /* add support for "eth1addr" */
-
-/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM
- * (see CONFIG_SYS_I2C_EEPROM) */
- /* MAC address offset in I2C EEPROM */
-#define CONFIG_SYS_I2C_MAC_OFFSET 0x7f00
-
-#define CONFIG_NETDEV "eth1"
-
-#define CONFIG_HOSTNAME "mpc8323erdb"
-#define CONFIG_ROOTPATH "/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
- /* U-Boot image on TFTP server */
-#define CONFIG_UBOOTPATH "u-boot.bin"
-#define CONFIG_FDTFILE "mpc832x_rdb.dtb"
-#define CONFIG_RAMDISKFILE "rootfs.ext2.gz.uboot"
-
- /* default location for tftp and bootm */
-#define CONFIG_LOADADDR 800000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=" CONFIG_NETDEV "\0" \
- "uboot=" CONFIG_UBOOTPATH "\0" \
- "tftpflash=tftp $loadaddr $uboot;" \
- "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize; " \
- "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize\0" \
- "fdtaddr=780000\0" \
- "fdtfile=" CONFIG_FDTFILE "\0" \
- "ramdiskaddr=1000000\0" \
- "ramdiskfile=" CONFIG_RAMDISKFILE "\0" \
- "console=ttyS0\0" \
- "setbootargs=setenv bootargs " \
- "root=$rootdev rw console=$console,$baudrate $othbootargs\0"\
- "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"\
- "$netdev:off "\
- "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv rootdev /dev/nfs;" \
- "run setbootargs;" \
- "run setipargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv rootdev /dev/ram;" \
- "run setbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / commitdiff