#include <asm/arch/reset_manager.h>
#include <asm/io.h>
+#include <usb.h>
+#include <usb/s3c_udc.h>
+#include <usb_mass_storage.h>
+
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
return 0;
}
+
+#ifdef CONFIG_USB_GADGET
+struct s3c_plat_otg_data socfpga_otg_data = {
+ .regs_otg = CONFIG_USB_DWC2_REG_ADDR,
+ .usb_gusbcfg = 0x1417,
+};
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+ return s3c_udc_probe(&socfpga_otg_data);
+}
+
+int g_dnl_board_usb_cable_connected(void)
+{
+ return 1;
+}
+#endif
perq = usb_stor_buf[0];
modi = usb_stor_buf[1];
- if ((perq & 0x1f) == 0x1f) {
- /* skip unknown devices */
+ /*
+ * Skip unknown devices (0x1f) and enclosure service devices (0x0d),
+ * they would not respond to test_unit_ready .
+ */
+ if (((perq & 0x1f) == 0x1f) || ((perq & 0x1f) == 0x0d)) {
return 0;
}
if ((modi&0x80) == 0x80) {
# new USB host ethernet layer dependencies
obj-$(CONFIG_USB_HOST_ETHER) += usb_ether.o
-ifdef CONFIG_USB_ETHER_ASIX
-obj-y += asix.o
-endif
+obj-$(CONFIG_USB_ETHER_ASIX) += asix.o
obj-$(CONFIG_USB_ETHER_MCS7830) += mcs7830.o
obj-$(CONFIG_USB_ETHER_SMSC95XX) += smsc95xx.o
ifdef CONFIG_USB_GADGET
obj-$(CONFIG_USB_GADGET_ATMEL_USBA) += atmel_usba_udc.o
obj-$(CONFIG_USB_GADGET_S3C_UDC_OTG) += s3c_udc_otg.o
+obj-$(CONFIG_USB_GADGET_S3C_UDC_OTG_PHY) += s3c_udc_otg_phy.o
obj-$(CONFIG_USB_GADGET_FOTG210) += fotg210.o
obj-$(CONFIG_CI_UDC) += ci_udc.o
obj-$(CONFIG_THOR_FUNCTION) += f_thor.o
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/gpio.h>
#include "regs-otg.h"
#include <usb/lin_gadget_compat.h>
struct usb_gadget_driver *driver);
static int udc_enable(struct s3c_udc *dev);
static void udc_set_address(struct s3c_udc *dev, unsigned char address);
-static void reconfig_usbd(void);
+static void reconfig_usbd(struct s3c_udc *dev);
static void set_max_pktsize(struct s3c_udc *dev, enum usb_device_speed speed);
static void nuke(struct s3c_ep *ep, int status);
static int s3c_udc_set_halt(struct usb_ep *_ep, int value);
void __iomem *regs_otg;
struct s3c_usbotg_reg *reg;
-struct s3c_usbotg_phy *phy;
-static unsigned int usb_phy_ctrl;
bool dfu_usb_get_reset(void)
{
return !!(readl(®->gintsts) & INT_RESET);
}
-void otg_phy_init(struct s3c_udc *dev)
-{
- dev->pdata->phy_control(1);
-
- /*USB PHY0 Enable */
- printf("USB PHY0 Enable\n");
-
- /* Enable PHY */
- writel(readl(usb_phy_ctrl) | USB_PHY_CTRL_EN0, usb_phy_ctrl);
-
- if (dev->pdata->usb_flags == PHY0_SLEEP) /* C210 Universal */
- writel((readl(&phy->phypwr)
- &~(PHY_0_SLEEP | OTG_DISABLE_0 | ANALOG_PWRDOWN)
- &~FORCE_SUSPEND_0), &phy->phypwr);
- else /* C110 GONI */
- writel((readl(&phy->phypwr) &~(OTG_DISABLE_0 | ANALOG_PWRDOWN)
- &~FORCE_SUSPEND_0), &phy->phypwr);
-
- if (s5p_cpu_id == 0x4412)
- writel((readl(&phy->phyclk) & ~(EXYNOS4X12_ID_PULLUP0 |
- EXYNOS4X12_COMMON_ON_N0)) | EXYNOS4X12_CLK_SEL_24MHZ,
- &phy->phyclk); /* PLL 24Mhz */
- else
- writel((readl(&phy->phyclk) & ~(ID_PULLUP0 | COMMON_ON_N0)) |
- CLK_SEL_24MHZ, &phy->phyclk); /* PLL 24Mhz */
-
- writel((readl(&phy->rstcon) &~(LINK_SW_RST | PHYLNK_SW_RST))
- | PHY_SW_RST0, &phy->rstcon);
- udelay(10);
- writel(readl(&phy->rstcon)
- &~(PHY_SW_RST0 | LINK_SW_RST | PHYLNK_SW_RST), &phy->rstcon);
- udelay(10);
-}
-
-void otg_phy_off(struct s3c_udc *dev)
-{
- /* reset controller just in case */
- writel(PHY_SW_RST0, &phy->rstcon);
- udelay(20);
- writel(readl(&phy->phypwr) &~PHY_SW_RST0, &phy->rstcon);
- udelay(20);
-
- writel(readl(&phy->phypwr) | OTG_DISABLE_0 | ANALOG_PWRDOWN
- | FORCE_SUSPEND_0, &phy->phypwr);
-
- writel(readl(usb_phy_ctrl) &~USB_PHY_CTRL_EN0, usb_phy_ctrl);
-
- writel((readl(&phy->phyclk) & ~(ID_PULLUP0 | COMMON_ON_N0)),
- &phy->phyclk);
-
- udelay(10000);
-
- dev->pdata->phy_control(0);
-}
+__weak void otg_phy_init(struct s3c_udc *dev) {}
+__weak void otg_phy_off(struct s3c_udc *dev) {}
/***********************************************************/
debug_cond(DEBUG_SETUP != 0, "%s: %p\n", __func__, dev);
otg_phy_init(dev);
- reconfig_usbd();
+ reconfig_usbd(dev);
debug_cond(DEBUG_SETUP != 0,
"S3C USB 2.0 OTG Controller Core Initialized : 0x%x\n",
udc_reinit(dev);
}
-static void reconfig_usbd(void)
+static void reconfig_usbd(struct s3c_udc *dev)
{
/* 2. Soft-reset OTG Core and then unreset again. */
int i;
unsigned int uTemp = writel(CORE_SOFT_RESET, ®->grstctl);
+ uint32_t dflt_gusbcfg;
debug("Reseting OTG controller\n");
- writel(0<<15 /* PHY Low Power Clock sel*/
+ dflt_gusbcfg =
+ 0<<15 /* PHY Low Power Clock sel*/
|1<<14 /* Non-Periodic TxFIFO Rewind Enable*/
|0x5<<10 /* Turnaround time*/
|0<<9 | 0<<8 /* [0:HNP disable,1:HNP enable][ 0:SRP disable*/
|0<<6 /* 0: high speed utmi+, 1: full speed serial*/
|0<<4 /* 0: utmi+, 1:ulpi*/
|1<<3 /* phy i/f 0:8bit, 1:16bit*/
- |0x7<<0, /* HS/FS Timeout**/
- ®->gusbcfg);
+ |0x7<<0; /* HS/FS Timeout**/
+
+ if (dev->pdata->usb_gusbcfg)
+ dflt_gusbcfg = dev->pdata->usb_gusbcfg;
+
+ writel(dflt_gusbcfg, ®->gusbcfg);
/* 3. Put the OTG device core in the disconnected state.*/
uTemp = readl(®->dctl);
dev->pdata = pdata;
- phy = (struct s3c_usbotg_phy *)pdata->regs_phy;
reg = (struct s3c_usbotg_reg *)pdata->regs_otg;
- usb_phy_ctrl = pdata->usb_phy_ctrl;
/* regs_otg = (void *)pdata->regs_otg; */
--- /dev/null
+/*
+ * drivers/usb/gadget/s3c_udc_otg.c
+ * Samsung S3C on-chip full/high speed USB OTG 2.0 device controllers
+ *
+ * Copyright (C) 2008 for Samsung Electronics
+ *
+ * BSP Support for Samsung's UDC driver
+ * available at:
+ * git://git.kernel.org/pub/scm/linux/kernel/git/kki_ap/linux-2.6-samsung.git
+ *
+ * State machine bugfixes:
+ * Marek Szyprowski <m.szyprowski@samsung.com>
+ *
+ * Ported to u-boot:
+ * Marek Szyprowski <m.szyprowski@samsung.com>
+ * Lukasz Majewski <l.majewski@samsumg.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/errno.h>
+#include <linux/list.h>
+#include <malloc.h>
+
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+
+#include <asm/byteorder.h>
+#include <asm/unaligned.h>
+#include <asm/io.h>
+
+#include <asm/mach-types.h>
+
+#include "regs-otg.h"
+#include <usb/lin_gadget_compat.h>
+
+#include <usb/s3c_udc.h>
+
+void otg_phy_init(struct s3c_udc *dev)
+{
+ unsigned int usb_phy_ctrl = dev->pdata->usb_phy_ctrl;
+ struct s3c_usbotg_phy *phy =
+ (struct s3c_usbotg_phy *)dev->pdata->regs_phy;
+
+ dev->pdata->phy_control(1);
+
+ /* USB PHY0 Enable */
+ printf("USB PHY0 Enable\n");
+
+ /* Enable PHY */
+ writel(readl(usb_phy_ctrl) | USB_PHY_CTRL_EN0, usb_phy_ctrl);
+
+ if (dev->pdata->usb_flags == PHY0_SLEEP) /* C210 Universal */
+ writel((readl(&phy->phypwr)
+ &~(PHY_0_SLEEP | OTG_DISABLE_0 | ANALOG_PWRDOWN)
+ &~FORCE_SUSPEND_0), &phy->phypwr);
+ else /* C110 GONI */
+ writel((readl(&phy->phypwr) &~(OTG_DISABLE_0 | ANALOG_PWRDOWN)
+ &~FORCE_SUSPEND_0), &phy->phypwr);
+
+ if (s5p_cpu_id == 0x4412)
+ writel((readl(&phy->phyclk) & ~(EXYNOS4X12_ID_PULLUP0 |
+ EXYNOS4X12_COMMON_ON_N0)) | EXYNOS4X12_CLK_SEL_24MHZ,
+ &phy->phyclk); /* PLL 24Mhz */
+ else
+ writel((readl(&phy->phyclk) & ~(ID_PULLUP0 | COMMON_ON_N0)) |
+ CLK_SEL_24MHZ, &phy->phyclk); /* PLL 24Mhz */
+
+ writel((readl(&phy->rstcon) &~(LINK_SW_RST | PHYLNK_SW_RST))
+ | PHY_SW_RST0, &phy->rstcon);
+ udelay(10);
+ writel(readl(&phy->rstcon)
+ &~(PHY_SW_RST0 | LINK_SW_RST | PHYLNK_SW_RST), &phy->rstcon);
+ udelay(10);
+}
+
+void otg_phy_off(struct s3c_udc *dev)
+{
+ unsigned int usb_phy_ctrl = dev->pdata->usb_phy_ctrl;
+ struct s3c_usbotg_phy *phy =
+ (struct s3c_usbotg_phy *)dev->pdata->regs_phy;
+
+ /* reset controller just in case */
+ writel(PHY_SW_RST0, &phy->rstcon);
+ udelay(20);
+ writel(readl(&phy->phypwr) &~PHY_SW_RST0, &phy->rstcon);
+ udelay(20);
+
+ writel(readl(&phy->phypwr) | OTG_DISABLE_0 | ANALOG_PWRDOWN
+ | FORCE_SUSPEND_0, &phy->phypwr);
+
+ writel(readl(usb_phy_ctrl) &~USB_PHY_CTRL_EN0, usb_phy_ctrl);
+
+ writel((readl(&phy->phyclk) & ~(ID_PULLUP0 | COMMON_ON_N0)),
+ &phy->phyclk);
+
+ udelay(10000);
+
+ dev->pdata->phy_control(0);
+}
debug_cond(DEBUG_ISR,
"\t\tOTG core got reset (%d)!!\n",
reset_available);
- reconfig_usbd();
+ reconfig_usbd(dev);
dev->ep0state = WAIT_FOR_SETUP;
reset_available = 0;
s3c_udc_pre_setup();
#include "ehci.h"
#if defined(CONFIG_R8A7740)
-static u32 usb_base_address[CONFIG_USB_MAX_CONTROLLER_COUNT] = {
+static u32 usb_base_address[] = {
0xC6700000
};
#elif defined(CONFIG_R8A7790)
-static u32 usb_base_address[CONFIG_USB_MAX_CONTROLLER_COUNT] = {
+static u32 usb_base_address[] = {
0xEE080000, /* USB0 (EHCI) */
0xEE0A0000, /* USB1 */
0xEE0C0000, /* USB2 */
};
#elif defined(CONFIG_R8A7791) || defined(CONFIG_R8A7793) || \
defined(CONFIG_R8A7794)
-static u32 usb_base_address[CONFIG_USB_MAX_CONTROLLER_COUNT] = {
+static u32 usb_base_address[] = {
0xEE080000, /* USB0 (EHCI) */
0xEE0C0000, /* USB1 */
};
if (!i)
printf("error : ehci(%d) reset failed.\n", index);
- if (index == (CONFIG_USB_MAX_CONTROLLER_COUNT - 1))
+ if (index == (ARRAY_SIZE(usb_base_address) - 1))
setbits_le32(SMSTPCR7, SMSTPCR703);
return 0;
uint32_t or_usbcmd;
#define CMD_PARK (1 << 11) /* enable "park" */
#define CMD_PARK_CNT(c) (((c) >> 8) & 3) /* how many transfers to park */
-#define CMD_ASE (1 << 5) /* async schedule enable */
#define CMD_LRESET (1 << 7) /* partial reset */
-#define CMD_IAAD (1 << 5) /* "doorbell" interrupt */
+#define CMD_IAAD (1 << 6) /* "doorbell" interrupt */
+#define CMD_ASE (1 << 5) /* async schedule enable */
#define CMD_PSE (1 << 4) /* periodic schedule enable */
#define CMD_RESET (1 << 1) /* reset HC not bus */
#define CMD_RUN (1 << 0) /* start/stop HC */
#define CONFIG_USB_GADGET
#define CONFIG_USB_GADGET_S3C_UDC_OTG
+#define CONFIG_USB_GADGET_S3C_UDC_OTG_PHY
#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_USB_GADGET_VBUS_DRAW 2
#define CONFIG_SYS_MAX_I2C_BUS 7
#define CONFIG_USB_GADGET
#define CONFIG_USB_GADGET_S3C_UDC_OTG
+#define CONFIG_USB_GADGET_S3C_UDC_OTG_PHY
#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_USB_GADGET_VBUS_DRAW 2
#define CONFIG_CMD_USB_MASS_STORAGE
#define CONFIG_USB_GADGET
#define CONFIG_USB_GADGET_S3C_UDC_OTG
+#define CONFIG_USB_GADGET_S3C_UDC_OTG_PHY
#define CONFIG_USB_GADGET_DUALSPEED
/*
#undef CONFIG_BOARD_COMMON
#undef CONFIG_USB_GADGET
#undef CONFIG_USB_GADGET_S3C_UDC_OTG
+#undef CONFIG_USB_GADGET_S3C_UDC_OTG_PHY
#undef CONFIG_CMD_USB_MASS_STORAGE
#undef CONFIG_REVISION_TAG
#undef CONFIG_CMD_THOR_DOWNLOAD
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x0
-#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024)
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
#endif
/*
+ * USB Gadget (DFU, UMS)
+ */
+#if defined(CONFIG_CMD_DFU) || defined(CONFIG_CMD_USB_MASS_STORAGE)
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_S3C_UDC_OTG
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+
+/* USB Composite download gadget - g_dnl */
+#define CONFIG_USBDOWNLOAD_GADGET
+#define CONFIG_USB_GADGET_MASS_STORAGE
+
+#define CONFIG_DFU_FUNCTION
+#define CONFIG_DFU_MMC
+#define CONFIG_SYS_DFU_DATA_BUF_SIZE (32 * 1024 * 1024)
+#define DFU_DEFAULT_POLL_TIMEOUT 300
+
+/* USB IDs */
+#define CONFIG_G_DNL_VENDOR_NUM 0x0525 /* NetChip */
+#define CONFIG_G_DNL_PRODUCT_NUM 0xA4A5 /* Linux-USB File-backed Storage Gadget */
+#define CONFIG_G_DNL_UMS_VENDOR_NUM CONFIG_G_DNL_VENDOR_NUM
+#define CONFIG_G_DNL_UMS_PRODUCT_NUM CONFIG_G_DNL_PRODUCT_NUM
+#ifndef CONFIG_G_DNL_MANUFACTURER
+#define CONFIG_G_DNL_MANUFACTURER "Altera"
+#endif
+#endif
+
+/*
* U-Boot environment
*/
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#include <usb_defs.h>
#include <linux/usb/ch9.h>
+#include <asm/cache.h>
+#include <part.h>
/*
* The EHCI spec says that we must align to at least 32 bytes. However,
unsigned int regs_otg;
unsigned int usb_phy_ctrl;
unsigned int usb_flags;
+ unsigned int usb_gusbcfg;
};
#endif
projects / platform / kernel / u-boot.git / commitdiff