development platform that supports the QorIQ LS1046A
Layerscape Architecture processor.
+config TARGET_LS1046AFRWY
+ bool "Support ls1046afrwy"
+ select ARCH_LS1046A
+ select ARM64
+ select ARMV8_MULTIENTRY
+ select BOARD_EARLY_INIT_F
+ select BOARD_LATE_INIT
+ select DM_SPI_FLASH if DM_SPI
+ imply SCSI
+ help
+ Support for Freescale LS1046AFRWY platform.
+ The LS1046A Freeway Board (FRWY) is a high-performance
+ development platform that supports the QorIQ LS1046A
+ Layerscape Architecture processor.
config TARGET_H2200
bool "Support h2200"
select CPU_PXA
source "board/freescale/ls1046aqds/Kconfig"
source "board/freescale/ls1043ardb/Kconfig"
source "board/freescale/ls1046ardb/Kconfig"
+source "board/freescale/ls1046afrwy/Kconfig"
source "board/freescale/ls1012aqds/Kconfig"
source "board/freescale/ls1012ardb/Kconfig"
source "board/freescale/ls1012afrdm/Kconfig"
!TARGET_LS1028ARDB && !TARGET_LS1028AQDS && \
!TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \
!TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \
+ !TARGET_LS1046AFRWY && \
!TARGET_LS2081ARDB && !TARGET_LX2160ARDB && \
!TARGET_LX2160AQDS && \
!ARCH_UNIPHIER && !TARGET_S32V234EVB
select SYS_I2C_MXC_I2C6
select SYS_I2C_MXC_I2C7
select SYS_I2C_MXC_I2C8
+ select SYS_FSL_ERRATUM_A008997
select SYS_FSL_ERRATUM_A009007
select SYS_FSL_ERRATUM_A008514 if !TFABOOT
select SYS_FSL_ERRATUM_A009663 if !TFABOOT
do_fixup_by_path_u32(blob, "/sysclk", "clock-frequency",
CONFIG_SYS_CLK_FREQ, 1);
-#ifdef CONFIG_PCI
+#ifdef CONFIG_PCI_LAYERSCAPE
ft_pci_setup(blob, bd);
#endif
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP.
*/
#include <common.h>
return get_i2c_freq(0);
#if defined(CONFIG_FSL_ESDHC)
case MXC_ESDHC_CLK:
+ case MXC_ESDHC2_CLK:
return get_sdhc_freq(0);
#endif
case MXC_DSPI_CLK:
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2014-2015, Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP Semiconductors
*
* Derived from arch/power/cpu/mpc85xx/speed.c
*/
return get_i2c_freq(0);
#if defined(CONFIG_FSL_ESDHC)
case MXC_ESDHC_CLK:
+ case MXC_ESDHC2_CLK:
return get_sdhc_freq(0);
#endif
case MXC_DSPI_CLK:
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2014-2015 Freescale Semiconductor
+ * Copyright 2019 NXP
*
* Extracted from armv8/start.S
*/
#if defined(CONFIG_SYS_FSL_HAS_CCN504) || defined(CONFIG_SYS_FSL_HAS_CCN508)
hnf_pstate_poll:
- /* x0 has the desired status, return 0 for success, 1 for timeout
- * clobber x1, x2, x3, x4, x6, x7
+ /* x0 has the desired status, return only if operation succeed
+ * clobber x1, x2, x6
*/
mov x1, x0
- mov x7, #0 /* flag for timeout */
- mrs x3, cntpct_el0 /* read timer */
- add x3, x3, #1200 /* timeout after 100 microseconds */
+ mov w6, #8 /* HN-F node count */
mov x0, #0x18
movk x0, #0x420, lsl #16 /* HNF0_PSTATE_STATUS */
- mov w6, #8 /* HN-F node count */
1:
ldr x2, [x0]
cmp x2, x1 /* check status */
b.eq 2f
- mrs x4, cntpct_el0
- cmp x4, x3
- b.ls 1b
- mov x7, #1 /* timeout */
- b 3f
+ b 1b
2:
add x0, x0, #0x10000 /* move to next node */
subs w6, w6, #1
cbnz w6, 1b
-3:
- mov x0, x7
ret
hnf_set_pstate:
/*
* Return status in x0
* success 0
- * timeout 1 for setting SFONLY, 2 for FAM, 3 for both
*/
mov x29, lr
- mov x8, #0
dsb sy
mov x0, #0x1 /* HNFPSTAT_SFONLY */
mov x0, #0x4 /* SFONLY status */
bl hnf_pstate_poll
- cbz x0, 1f
- mov x8, #1 /* timeout */
-1:
+
dsb sy
mov x0, #0x3 /* HNFPSTAT_FAM */
bl hnf_set_pstate
mov x0, #0xc /* FAM status */
bl hnf_pstate_poll
- cbz x0, 1f
- add x8, x8, #0x2
-1:
- mov x0, x8
+
+ mov x0, #0
mov lr, x29
ret
ENDPROC(__asm_flush_l3_dcache)
{0xEBCC, {PCIE1, PCIE1, PCIE2, SATA1} },
{0xCCCC, {PCIE1, PCIE1, PCIE2, PCIE2} },
{0xDDDD, {PCIE1, PCIE1, PCIE1, PCIE1} },
+ {0xE031, {SXGMII1, QXGMII2, NONE, SATA1} },
+ {0xB991, {SXGMII1, SGMII1, SGMII2, PCIE1} },
+ {0xBB31, {SXGMII1, QXGMII2, PCIE1, PCIE1} },
+ {0xCC31, {SXGMII1, QXGMII2, PCIE2, PCIE2} },
+ {0xBB51, {SXGMII1, QSGMII_B, PCIE2, PCIE1} },
+ {0xBB38, {SGMII_T1, QXGMII2, PCIE2, PCIE1} },
+ {0xCC38, {SGMII_T1, QXGMII2, PCIE2, PCIE2} },
+ {0xBB58, {SGMII_T1, QSGMII_B, PCIE2, PCIE1} },
+ {0xCC58, {SGMII_T1, QSGMII_B, PCIE2, PCIE2} },
+ {0xCC8B, {PCIE1, SGMII_T1, PCIE2, PCIE2} },
+ {0xEB58, {SGMII_T1, QSGMII_B, PCIE2, SATA1} },
+ {0xEB8B, {PCIE1, SGMII_T1, PCIE2, SATA1} },
+ {0xE8CC, {PCIE1, PCIE1, SGMII_T1, SATA1} },
{}
};
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2016 Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP
*/
#include <common.h>
{0x1163, {XFI_FM1_MAC9, XFI_FM1_MAC10, PCIE1, SGMII_FM1_DTSEC6} },
{0x2263, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10, PCIE1,
SGMII_FM1_DTSEC6} },
- {0x3363, {SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6, PCIE1,
+ {0x3363, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, PCIE1,
SGMII_FM1_DTSEC6} },
{0x2223, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10,
SGMII_2500_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x3040, {SGMII_FM1_DTSEC9, NONE, QSGMII_FM1_A, NONE} },
{}
};
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2014-2015 Freescale Semiconductor
+ * Copyright 2019 NXP
*/
#include <common.h>
set_usb_pcstxswingfull(scfg, SCFG_USB3PRM2CR_USB2);
set_usb_pcstxswingfull(scfg, SCFG_USB3PRM2CR_USB3);
#endif
+#elif defined(CONFIG_ARCH_LS1028A)
+ clrsetbits_le32(DCSR_BASE + DCSR_USB_IOCR1,
+ 0x7F << 11,
+ DCSR_USB_PCSTXSWINGFULL << 11);
#endif
#endif /* CONFIG_SYS_FSL_ERRATUM_A008997 */
}
out_be16((phy) + SCFG_USB_PHY_RX_OVRD_IN_HI, USB_PHY_RX_EQ_VAL_3); \
out_be16((phy) + SCFG_USB_PHY_RX_OVRD_IN_HI, USB_PHY_RX_EQ_VAL_4)
-#elif defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1088A)
+#elif defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1088A) || \
+ defined(CONFIG_ARCH_LS1028A)
#define PROGRAM_USB_PHY_RX_OVRD_IN_HI(phy) \
out_le16((phy) + DCSR_USB_PHY_RX_OVRD_IN_HI, USB_PHY_RX_EQ_VAL_1); \
usb_phy = (void __iomem *)SCFG_USB_PHY3;
PROGRAM_USB_PHY_RX_OVRD_IN_HI(usb_phy);
#endif
-#elif defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1088A)
+#elif defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1088A) || \
+ defined(CONFIG_ARCH_LS1028A)
void __iomem *dcsr = (void __iomem *)DCSR_BASE;
PROGRAM_USB_PHY_RX_OVRD_IN_HI(dcsr + DCSR_USB_PHY1);
struct ccsr_cci400 *cci = (struct ccsr_cci400 *)(CONFIG_SYS_IMMR +
CONFIG_SYS_CCI400_OFFSET);
struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+#if defined(CONFIG_FSL_QSPI) && defined(CONFIG_TFABOOT)
+ enum boot_src src;
+#endif
#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
enable_layerscape_ns_access();
init_early_memctl_regs(); /* tighten IFC timing */
#endif
+#if defined(CONFIG_FSL_QSPI) && defined(CONFIG_TFABOOT)
+ src = get_boot_src();
+ if (src != BOOT_SOURCE_QSPI_NOR)
+ out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
+#else
#if defined(CONFIG_FSL_QSPI) && !defined(CONFIG_QSPI_BOOT)
out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
#endif
+#endif
/* Make SEC reads and writes snoopable */
setbits_be32(&scfg->snpcnfgcr, SCFG_SNPCNFGCR_SECRDSNP |
SCFG_SNPCNFGCR_SECWRSNP |
* check if gd->env_addr is default_environment; then setenv bootcmd
* and mcinitcmd.
*/
+#if !defined(CONFIG_ENV_ADDR) || defined(ENV_IS_EMBEDDED)
+ if (gd->env_addr == (ulong)&default_environment[0]) {
+#else
if (gd->env_addr + gd->reloc_off == (ulong)&default_environment[0]) {
+#endif
fsl_setenv_bootcmd();
fsl_setenv_mcinitcmd();
}
fsl-ls1046a-qds-duart.dtb \
fsl-ls1046a-qds-lpuart.dtb \
fsl-ls1046a-rdb.dtb \
+ fsl-ls1046a-frwy.dtb \
fsl-ls1012a-qds.dtb \
fsl-ls1012a-rdb.dtb \
fsl-ls1012a-2g5rdb.dtb \
0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
};
+ pcie@1f0000000 {
+ compatible = "pci-host-ecam-generic";
+ /* ECAM bus 0, HW has more space reserved but not populated */
+ bus-range = <0x0 0x0>;
+ reg = <0x01 0xf0000000 0x0 0x100000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges= <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>;
+ };
+
i2c0: i2c@2000000 {
compatible = "fsl,vf610-i2c";
#address-cells = <1>;
sata: sata@3200000 {
compatible = "fsl,ls1028a-ahci";
- reg = <0x0 0x3200000 0x0 0x10000>;
+ reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */
+ 0x7 0x100520 0x0 0x4>; /* ecc sata addr*/
+ reg-names = "sata-base", "ecc-addr";
interrupts = <0 133 4>;
- clocks = <&clockgen 4 1>;
status = "disabled";
};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Device Tree Include file for NXP Layerscape-1046A family SoC.
+ *
+ * Copyright 2019 NXP
+ *
+ */
+
+/dts-v1/;
+/include/ "fsl-ls1046a.dtsi"
+
+/ {
+ model = "LS1046A FRWY Board";
+
+ aliases {
+ spi0 = &qspi;
+ };
+
+};
+
+&qspi {
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: mt25qu512abb8esf@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+
+};
+
compatible = "fsl,lx2160aqds", "fsl,lx2160a";
};
+&esdhc0 {
+ status = "okay";
+};
+
+&esdhc1 {
+ status = "okay";
+};
+
+&sata0 {
+ status = "okay";
+};
+
+&sata1 {
+ status = "okay";
+};
+
+&sata2 {
+ status = "okay";
+};
+
+&sata3 {
+ status = "okay";
+};
sata: sata@3200000 {
compatible = "fsl,ls1021a-ahci";
- reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */
- 0x0 0x20220520 0x0 0x4>; /* ecc sata addr*/
+ reg = <0x3200000 0x10000 0x20220520 0x4>;
reg-names = "sata-base", "ecc-addr";
interrupts = <0 101 4>;
status = "disabled";
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP Semiconductors
*
*/
MXC_BUS_CLK,
MXC_UART_CLK,
MXC_ESDHC_CLK,
+ MXC_ESDHC2_CLK,
MXC_I2C_CLK,
MXC_DSPI_CLK,
};
#else
#define CONFIG_SYS_PCIE1_PHYS_SIZE 0x800000000
#define CONFIG_SYS_PCIE2_PHYS_SIZE 0x800000000
+#ifndef CONFIG_SYS_PCIE3_PHYS_SIZE
#define CONFIG_SYS_PCIE3_PHYS_SIZE 0x800000000
+#endif
#define CONFIG_SYS_PCIE4_PHYS_SIZE 0x800000000
#define SYS_PCIE5_PHYS_SIZE 0x800000000
#define SYS_PCIE6_PHYS_SIZE 0x800000000
QSGMII_B,
QSGMII_C,
QSGMII_D,
+ SGMII_T1,
+ SGMII_T2,
+ SGMII_T3,
+ SGMII_T4,
+ SXGMII1,
+ SXGMII2,
+ SXGMII3,
+ SXGMII4,
+ QXGMII1,
+ QXGMII2,
+ QXGMII3,
+ QXGMII4,
_25GE1,
_25GE2,
_25GE3,
#elif CONFIG_ARCH_LS1028A
#define CONFIG_SYS_PCIE1_PHYS_ADDR 0x8000000000ULL
#define CONFIG_SYS_PCIE2_PHYS_ADDR 0x8800000000ULL
+#define CONFIG_SYS_PCIE3_PHYS_ADDR 0x01f0000000ULL
+/* this is used by integrated PCI on LS1028, includes ECAM and register space */
+#define CONFIG_SYS_PCIE3_PHYS_SIZE 0x0010000000ULL
#else
#define CONFIG_SYS_PCIE1_PHYS_ADDR 0x1000000000ULL
#define CONFIG_SYS_PCIE2_PHYS_ADDR 0x1200000000ULL
#define USB_PHY_RX_EQ_VAL_2 0x0080
#define USB_PHY_RX_EQ_VAL_3 0x0380
#define USB_PHY_RX_EQ_VAL_4 0x0b80
+#define DCSR_USB_IOCR1 0x108004
+#define DCSR_USB_PCSTXSWINGFULL 0x71
#define TP_ITYP_AV 0x00000001 /* Initiator available */
#define TP_ITYP_TYPE(x) (((x) & 0x6) >> 1) /* Initiator Type */
* bootdelay = 0 (To disable Boot Prompt)
* bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)
*/
- env_set("bootdelay", "0");
+ env_set("bootdelay", "-2");
#ifdef CONFIG_ARM
env_set("secureboot", "y");
F: include/configs/ls1028a_common.h
F: include/configs/ls1028ardb.h
F: configs/ls1028ardb_tfa_defconfig
+
+LS1028AQDS_SECURE_BOOT BOARD
+M: Tang Yuantian <andy.tang@nxp.com>
+S: Maintained
+F: configs/ls1028aqds_tfa_SECURE_BOOT_defconfig
+
+LS1028ARDB_SECURE_BOOT BOARD
+M: Tang Yuantian <andy.tang@nxp.com>
+S: Maintained
+F: configs/ls1028ardb_tfa_SECURE_BOOT_defconfig
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP
*/
#include <common.h>
if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
if (port == FM1_DTSEC9) {
fdt_set_phy_handle(fdt, compat, addr,
- "sgmii_riser_s1_p1");
+ "sgmii-riser-s1-p1");
} else if (port == FM1_DTSEC2) {
fdt_set_phy_handle(fdt, compat, addr,
- "sgmii_riser_s2_p1");
+ "sgmii-riser-s2-p1");
} else if (port == FM1_DTSEC5) {
fdt_set_phy_handle(fdt, compat, addr,
- "sgmii_riser_s3_p1");
+ "sgmii-riser-s3-p1");
} else if (port == FM1_DTSEC6) {
fdt_set_phy_handle(fdt, compat, addr,
- "sgmii_riser_s4_p1");
+ "sgmii-riser-s4-p1");
}
} else if (fm_info_get_enet_if(port) ==
PHY_INTERFACE_MODE_SGMII_2500) {
switch (port) {
case FM1_DTSEC1:
fdt_set_phy_handle(fdt, compat, addr,
- "qsgmii_s1_p1");
+ "qsgmii-s1-p1");
break;
case FM1_DTSEC2:
fdt_set_phy_handle(fdt, compat, addr,
- "qsgmii_s1_p2");
+ "qsgmii-s1-p2");
break;
case FM1_DTSEC5:
fdt_set_phy_handle(fdt, compat, addr,
- "qsgmii_s1_p3");
+ "qsgmii-s1-p3");
break;
case FM1_DTSEC6:
fdt_set_phy_handle(fdt, compat, addr,
- "qsgmii_s1_p4");
+ "qsgmii-s1-p4");
break;
default:
break;
switch (port) {
case FM1_DTSEC1:
fdt_set_phy_handle(fdt, compat, addr,
- "qsgmii_s2_p1");
+ "qsgmii-s2-p1");
break;
case FM1_DTSEC2:
fdt_set_phy_handle(fdt, compat, addr,
- "qsgmii_s2_p2");
+ "qsgmii-s2-p2");
break;
case FM1_DTSEC5:
fdt_set_phy_handle(fdt, compat, addr,
- "qsgmii_s2_p3");
+ "qsgmii-s2-p3");
break;
case FM1_DTSEC6:
fdt_set_phy_handle(fdt, compat, addr,
- "qsgmii_s2_p4");
+ "qsgmii-s2-p4");
break;
default:
break;
case PHY_INTERFACE_MODE_QSGMII:
switch (mdio_mux[i]) {
case EMI1_SLOT1:
- fdt_status_okay_by_alias(fdt, "emi1_slot1");
+ fdt_status_okay_by_alias(fdt, "emi1-slot1");
break;
case EMI1_SLOT2:
- fdt_status_okay_by_alias(fdt, "emi1_slot2");
+ fdt_status_okay_by_alias(fdt, "emi1-slot2");
break;
case EMI1_SLOT3:
- fdt_status_okay_by_alias(fdt, "emi1_slot3");
+ fdt_status_okay_by_alias(fdt, "emi1-slot3");
break;
case EMI1_SLOT4:
- fdt_status_okay_by_alias(fdt, "emi1_slot4");
+ fdt_status_okay_by_alias(fdt, "emi1-slot4");
break;
default:
break;
--- /dev/null
+
+if TARGET_LS1046AFRWY
+
+config SYS_BOARD
+ default "ls1046afrwy"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls1046afrwy"
+
+source "board/freescale/common/Kconfig"
+endif
--- /dev/null
+LS1046AFRWY BOARD
+M: Pramod Kumar <pramod.kumar_1@nxp.com>
+S: Maintained
+F: board/freescale/ls1046afrwy/
+F: board/freescale/ls1046afrwy/ls1046afrwy.c
+F: include/configs/ls1046afrwy.h
+F: configs/ls1046afrwy_tfa_defconfig
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright 2019 NXP
+
+obj-y += ddr.o
+obj-y += ls1046afrwy.o
+obj-$(CONFIG_NET) += eth.o
--- /dev/null
+Overview
+--------
+The LS1046A Freeway Board (iFRWY) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LS1046A
+LayerScape Architecture processor. The FRWY-LS1046A provides SW development
+platform for the Freescale LS1046A processor series, with a complete
+debugging environment. The FRWY-LS1046A is lead-free and RoHS-compliant.
+
+LS1046A SoC Overview
+--------------------
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS1046A
+SoC overview.
+
+ FRWY-LS1046A board Overview
+ -----------------------
+ - SERDES1 Connections, 4 lanes supporting:
+ - Lane0: Unused
+ - Lane1: Unused
+ - Lane2: QSGMII
+ - Lane3: Unused
+ - SERDES2 Connections, 4 lanes supporting:
+ - Lane0: Unused
+ - Lane1: PCIe3 with PCIe x1 slot
+ - Lane2: Unused
+ - Lane3: PCIe3 with PCIe x1 slot
+ - DDR Controller
+ - 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s
+ -IFC/Local Bus
+ - One 512 MB NAND flash with ECC support
+ - USB 3.0
+ - Two Type A port
+ - SDHC: connects directly to a full microSD slot
+ - QSPI: 64 MB high-speed flash Memory for boot code and storage
+ - 4 I2C controllers
+ - UART
+ - Two 4-pin serial ports at up to 115.2 Kbit/s
+ - Two DB9 D-Type connectors supporting one Serial port each
+ - ARM JTAG support
+
+Memory map from core's view
+----------------------------
+Start Address End Address Description Size
+0x00_0000_0000 - 0x00_000F_FFFF Secure Boot ROM 1MB
+0x00_0100_0000 - 0x00_0FFF_FFFF CCSRBAR 240MB
+0x00_1000_0000 - 0x00_1000_FFFF OCRAM0 64KB
+0x00_1001_0000 - 0x00_1001_FFFF OCRAM1 64KB
+0x00_2000_0000 - 0x00_20FF_FFFF DCSR 16MB
+0x00_7E80_0000 - 0x00_7E80_FFFF IFC - NAND Flash 64KB
+0x00_7FB0_0000 - 0x00_7FB0_0FFF IFC - CPLD 4KB
+0x00_8000_0000 - 0x00_FFFF_FFFF DRAM1 2GB
+0x05_0000_0000 - 0x05_07FF_FFFF QMAN S/W Portal 128M
+0x05_0800_0000 - 0x05_0FFF_FFFF BMAN S/W Portal 128M
+0x08_8000_0000 - 0x09_FFFF_FFFF DRAM2 6GB
+0x40_0000_0000 - 0x47_FFFF_FFFF PCI Express1 32G
+0x48_0000_0000 - 0x4F_FFFF_FFFF PCI Express2 32G
+0x50_0000_0000 - 0x57_FFFF_FFFF PCI Express3 32G
+
+QSPI flash map:
+Start Address End Address Description Size
+0x00_4000_0000 - 0x00_400F_FFFF RCW + PBI + BL2 1MB
+0x00_4010_0000 - 0x00_404F_FFFF FIP Image
+ (Bl31 + BL32(optee.
+ bin) + Bl33(uboot)
+ + headers for secure
+ boot) 4MB
+0x00_4050_0000 - 0x00_405F_FFFF Boot Firmware Env 1MB
+0x00_4060_0000 - 0x00_408F_FFFF Secure boot headers 3MB
+0x00_4090_0000 - 0x00_4093_FFFF FMan ucode 256KB
+0x00_4094_0000 - 0x00_4097_FFFF QE/uQE firmware 256KB
+0x00_409C_0000 - 0x00_409F_FFFF Reserved 256KB
+0x00_4100_0000 - 0x00_43FF_FFFF FIT Image 48MB
+
+Booting Options
+---------------
+a) QSPI boot
+b) microSD boot
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int fsl_initdram(void)
+{
+ gd->ram_size = tfa_get_dram_size();
+
+ if (!gd->ram_size)
+ gd->ram_size = fsl_ddr_sdram_size();
+
+ return 0;
+}
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <netdev.h>
+#include <fm_eth.h>
+#include <fsl_dtsec.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+
+#include "../common/fman.h"
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_FMAN_ENET
+ struct memac_mdio_info dtsec_mdio_info;
+ struct mii_dev *dev;
+ u32 srds_s1;
+ struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
+ srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ dtsec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+ /* QSGMII on lane B, MAC 6/5/10/1 */
+ fm_info_set_phy_address(FM1_DTSEC6, QSGMII_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC5, QSGMII_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC10, QSGMII_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, QSGMII_PORT4_PHY_ADDR);
+
+ switch (srds_s1) {
+ case 0x3040:
+ break;
+ default:
+ printf("Invalid SerDes protocol 0x%x for LS1046AFRWY\n",
+ srds_s1);
+ break;
+ }
+
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+ fm_info_set_mdio(FM1_DTSEC6, dev);
+ fm_info_set_mdio(FM1_DTSEC5, dev);
+ fm_info_set_mdio(FM1_DTSEC10, dev);
+ fm_info_set_mdio(FM1_DTSEC1, dev);
+
+ cpu_eth_init(bis);
+#endif
+
+ return pci_eth_init(bis);
+}
+
+#ifdef CONFIG_FMAN_ENET
+int fdt_update_ethernet_dt(void *blob)
+{
+ u32 srds_s1;
+ int i, prop;
+ int offset, nodeoff;
+ const char *path;
+ struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
+ srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ /* Cycle through all aliases */
+ for (prop = 0; ; prop++) {
+ const char *name;
+
+ /* FDT might have been edited, recompute the offset */
+ offset = fdt_first_property_offset(blob,
+ fdt_path_offset(blob,
+ "/aliases")
+ );
+ /* Select property number 'prop' */
+ for (i = 0; i < prop; i++)
+ offset = fdt_next_property_offset(blob, offset);
+
+ if (offset < 0)
+ break;
+
+ path = fdt_getprop_by_offset(blob, offset, &name, NULL);
+ nodeoff = fdt_path_offset(blob, path);
+
+ switch (srds_s1) {
+ case 0x3040:
+ if (!strcmp(name, "ethernet1"))
+ fdt_status_disabled(blob, nodeoff);
+ if (!strcmp(name, "ethernet2"))
+ fdt_status_disabled(blob, nodeoff);
+ if (!strcmp(name, "ethernet3"))
+ fdt_status_disabled(blob, nodeoff);
+ if (!strcmp(name, "ethernet6"))
+ fdt_status_disabled(blob, nodeoff);
+ break;
+ default:
+ printf("%s:Invalid SerDes prtcl 0x%x for LS1046AFRWY\n",
+ __func__, srds_s1);
+ break;
+ }
+ }
+
+ return 0;
+}
+#endif
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <fdt_support.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
+#include <asm/arch-fsl-layerscape/fsl_icid.h>
+#include <hwconfig.h>
+#include <ahci.h>
+#include <mmc.h>
+#include <scsi.h>
+#include <fm_eth.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include <fsl_sec.h>
+#include <fsl_dspi.h>
+
+#define LS1046A_PORSR1_REG 0x1EE0000
+#define BOOT_SRC_SD 0x20000000
+#define BOOT_SRC_MASK 0xFF800000
+#define BOARD_REV_GPIO 13
+#define USB2_SEL_MASK 0x00000100
+
+#define BYTE_SWAP_32(word) ((((word) & 0xff000000) >> 24) | \
+(((word) & 0x00ff0000) >> 8) | \
+(((word) & 0x0000ff00) << 8) | \
+(((word) & 0x000000ff) << 24))
+#define SPI_MCR_REG 0x2100000
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static inline void demux_select_usb2(void)
+{
+ u32 val;
+ struct ccsr_gpio *pgpio = (void *)(GPIO3_BASE_ADDR);
+
+ val = in_be32(&pgpio->gpdir);
+ val |= USB2_SEL_MASK;
+ out_be32(&pgpio->gpdir, val);
+
+ val = in_be32(&pgpio->gpdat);
+ val |= USB2_SEL_MASK;
+ out_be32(&pgpio->gpdat, val);
+}
+
+static inline void set_spi_cs_signal_inactive(void)
+{
+ /* default: all CS signals inactive state is high */
+ uint mcr_val;
+ uint mcr_cfg_val = DSPI_MCR_MSTR | DSPI_MCR_PCSIS_MASK |
+ DSPI_MCR_CRXF | DSPI_MCR_CTXF;
+
+ mcr_val = in_be32(SPI_MCR_REG);
+ mcr_val |= DSPI_MCR_HALT;
+ out_be32(SPI_MCR_REG, mcr_val);
+ out_be32(SPI_MCR_REG, mcr_cfg_val);
+ mcr_val = in_be32(SPI_MCR_REG);
+ mcr_val &= ~DSPI_MCR_HALT;
+ out_be32(SPI_MCR_REG, mcr_val);
+}
+
+int board_early_init_f(void)
+{
+ fsl_lsch2_early_init_f();
+
+ return 0;
+}
+
+static inline uint8_t get_board_version(void)
+{
+ u8 val;
+ struct ccsr_gpio *pgpio = (void *)(GPIO2_BASE_ADDR);
+
+ val = (in_le32(&pgpio->gpdat) >> BOARD_REV_GPIO) & 0x03;
+
+ return val;
+}
+
+int checkboard(void)
+{
+ static const char *freq[2] = {"100.00MHZ", "100.00MHZ"};
+ u32 boot_src;
+ u8 rev;
+
+ rev = get_board_version();
+ switch (rev) {
+ case 0x00:
+ puts("Board: LS1046AFRWY, Rev: A, boot from ");
+ break;
+ case 0x01:
+ puts("Board: LS1046AFRWY, Rev: B, boot from ");
+ break;
+ default:
+ puts("Board: LS1046AFRWY, Rev: Unknown, boot from ");
+ break;
+ }
+ boot_src = BYTE_SWAP_32(readl(LS1046A_PORSR1_REG));
+
+ if ((boot_src & BOOT_SRC_MASK) == BOOT_SRC_SD)
+ puts("SD\n");
+ else
+ puts("QSPI\n");
+ printf("SD1_CLK1 = %s, SD1_CLK2 = %s\n", freq[0], freq[1]);
+
+ return 0;
+}
+
+int board_init(void)
+{
+#ifdef CONFIG_SECURE_BOOT
+ /*
+ * In case of Secure Boot, the IBR configures the SMMU
+ * to allow only Secure transactions.
+ * SMMU must be reset in bypass mode.
+ * Set the ClientPD bit and Clear the USFCFG Bit
+ */
+ u32 val;
+val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
+ out_le32(SMMU_SCR0, val);
+ val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
+ out_le32(SMMU_NSCR0, val);
+#endif
+
+#ifdef CONFIG_FSL_CAAM
+ sec_init();
+#endif
+
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+ return 0;
+}
+
+int board_setup_core_volt(u32 vdd)
+{
+ return 0;
+}
+
+void config_board_mux(void)
+{
+#ifdef CONFIG_HAS_FSL_XHCI_USB
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+ u32 usb_pwrfault;
+ /*
+ * USB2 is used, configure mux to USB2_DRVVBUS/USB2_PWRFAULT
+ * USB3 is not used, configure mux to IIC4_SCL/IIC4_SDA
+ */
+ out_be32(&scfg->rcwpmuxcr0, 0x3300);
+#ifdef CONFIG_HAS_FSL_IIC3
+ /* IIC3 is used, configure mux to use IIC3_SCL/IIC3/SDA */
+ out_be32(&scfg->rcwpmuxcr0, 0x0000);
+#endif
+ out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
+ usb_pwrfault = (SCFG_USBPWRFAULT_DEDICATED <<
+ SCFG_USBPWRFAULT_USB3_SHIFT) |
+ (SCFG_USBPWRFAULT_DEDICATED <<
+ SCFG_USBPWRFAULT_USB2_SHIFT) |
+ (SCFG_USBPWRFAULT_SHARED <<
+ SCFG_USBPWRFAULT_USB1_SHIFT);
+ out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
+#ifndef CONFIG_HAS_FSL_IIC3
+ /*
+ * LS1046A FRWY board has demultiplexer NX3DV42GU with GPIO3_23 as input
+ * to select I2C3_USB2_SEL_IO
+ * I2C3_USB2_SEL = 0: I2C3_SCL/SDA signals are routed to
+ * I2C3 header (default)
+ * I2C3_USB2_SEL = 1: USB2_DRVVBUS/PWRFAULT signals are routed to
+ * USB2 port
+ * programmed to select USB2 by setting GPIO3_23 output to one
+ */
+ demux_select_usb2();
+#endif
+#endif
+ set_spi_cs_signal_inactive();
+}
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+ config_board_mux();
+ return 0;
+}
+#endif
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ u64 base[CONFIG_NR_DRAM_BANKS];
+ u64 size[CONFIG_NR_DRAM_BANKS];
+
+ /* fixup DT for the two DDR banks */
+ base[0] = gd->bd->bi_dram[0].start;
+ size[0] = gd->bd->bi_dram[0].size;
+ base[1] = gd->bd->bi_dram[1].start;
+ size[1] = gd->bd->bi_dram[1].size;
+
+ fdt_fixup_memory_banks(blob, base, size, 2);
+ ft_cpu_setup(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+#endif
+
+ fdt_fixup_icid(blob);
+
+ return 0;
+}
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2016 Freescale Semiconductor, Inc.
- * Copyright 2018 NXP
+ * Copyright 2018-2019 NXP
*/
#include <common.h>
if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
switch (port) {
case FM1_DTSEC9:
- fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p1");
+ fdt_set_phy_handle(fdt, compat, addr, "sgmii-s1-p1");
break;
case FM1_DTSEC10:
- fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p2");
+ fdt_set_phy_handle(fdt, compat, addr, "sgmii-s1-p2");
break;
case FM1_DTSEC5:
- fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p3");
+ fdt_set_phy_handle(fdt, compat, addr, "sgmii-s1-p3");
break;
case FM1_DTSEC6:
- fdt_set_phy_handle(fdt, compat, addr, "sgmii_s1_p4");
+ fdt_set_phy_handle(fdt, compat, addr, "sgmii-s1-p4");
break;
case FM1_DTSEC2:
- fdt_set_phy_handle(fdt, compat, addr, "sgmii_s4_p1");
+ fdt_set_phy_handle(fdt, compat, addr, "sgmii-s4-p1");
break;
default:
break;
} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) {
switch (port) {
case FM1_DTSEC1:
- fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p4");
+ fdt_set_phy_handle(fdt, compat, addr, "qsgmii-s2-p4");
break;
case FM1_DTSEC5:
- fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p2");
+ fdt_set_phy_handle(fdt, compat, addr, "qsgmii-s2-p2");
break;
case FM1_DTSEC6:
- fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p1");
+ fdt_set_phy_handle(fdt, compat, addr, "qsgmii-s2-p1");
break;
case FM1_DTSEC10:
- fdt_set_phy_handle(fdt, compat, addr, "qsgmii_s2_p3");
+ fdt_set_phy_handle(fdt, compat, addr, "qsgmii-s2-p3");
break;
default:
break;
case PHY_INTERFACE_MODE_QSGMII:
switch (mdio_mux[i]) {
case EMI1_SLOT1:
- fdt_status_okay_by_alias(fdt, "emi1_slot1");
+ fdt_status_okay_by_alias(fdt, "emi1-slot1");
break;
case EMI1_SLOT2:
- fdt_status_okay_by_alias(fdt, "emi1_slot2");
+ fdt_status_okay_by_alias(fdt, "emi1-slot2");
break;
case EMI1_SLOT4:
- fdt_status_okay_by_alias(fdt, "emi1_slot4");
+ fdt_status_okay_by_alias(fdt, "emi1-slot4");
break;
default:
break;
return;
}
- if ((get_mc_boot_status() == 0) && (get_dpl_apply_status() == 0)) {
+ if (get_mc_boot_status() == 0 &&
+ (is_lazy_dpl_addr_valid() || get_dpl_apply_status() == 0)) {
fdt_status_okay(fdt, offset);
fdt_fixup_board_phy(fdt);
} else {
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
# CONFIG_MMC is not set
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
# CONFIG_MMC is not set
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_DM_MMC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_DM_MMC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_DM_MMC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_SF_DEFAULT_BUS=1
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_SF_DEFAULT_BUS=1
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_SF_DEFAULT_BUS=1
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=10000000
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_E1000=y
CONFIG_PCI=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_E1000=y
CONFIG_PCI=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_FSL_ESDHC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_FSL_PFE=y
CONFIG_DM_ETH=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_DSPI=y
+CONFIG_FSL_QSPI=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_XHCI_HCD=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_TARGET_LS1028AQDS=y
+CONFIG_SECURE_BOOT=y
+CONFIG_SYS_FSL_SDHC_CLK_DIV=1
+CONFIG_TFABOOT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
+CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=10
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256 video=1920x1080-32@60 cma=256M"
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_WDT=y
+CONFIG_CMD_CACHE=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1028a-qds"
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_DM=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SATA_CEVA=y
+CONFIG_DM_MMC=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_E1000=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_LAYERSCAPE=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_SYS_NS16550=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_DSPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_WDT=y
+CONFIG_WDT_SP805=y
+CONFIG_RSA=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
CONFIG_PCI=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_ECAM_GENERIC=y
CONFIG_PCIE_LAYERSCAPE=y
CONFIG_SCSI=y
CONFIG_DM_SCSI=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_TARGET_LS1028ARDB=y
+CONFIG_SECURE_BOOT=y
+CONFIG_SYS_FSL_SDHC_CLK_DIV=1
+CONFIG_TFABOOT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
+CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_BOOTDELAY=10
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256 video=1920x1080-32@60 cma=256M"
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_WDT=y
+CONFIG_CMD_CACHE=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1028a-rdb"
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_DM=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SATA_CEVA=y
+CONFIG_DM_MMC=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_E1000=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_LAYERSCAPE=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_SYS_NS16550=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_DSPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_WDT=y
+CONFIG_WDT_SP805=y
+CONFIG_RSA=y
+CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
CONFIG_PCI=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_ECAM_GENERIC=y
CONFIG_PCIE_LAYERSCAPE=y
CONFIG_SCSI=y
CONFIG_DM_SCSI=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_TARGET_LS1046AFRWY=y
+CONFIG_SYS_TEXT_BASE=0x82000000
+CONFIG_QSPI_AHB_INIT=y
+CONFIG_TFABOOT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
+CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_BOOTDELAY=10
+CONFIG_USE_BOOTARGS=y
+CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=1550000.spi:1m(rcw),15m(u-boot),48m(kernel.itb);7e800000.flash:16m(nand_uboot),48m(nand_kernel),448m(nand_free)"
+CONFIG_MISC_INIT_R=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_CACHE=y
+CONFIG_MP=y
+CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.spi:1m(rcw),15m(u-boot),48m(kernel.itb);7e800000.flash:16m(nand_uboot),48m(nand_kernel),448m(nand_free)"
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-frwy"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_DM=y
+CONFIG_SATA_CEVA=y
+CONFIG_FSL_CAAM=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_SPI_FLASH=y
+# CONFIG_SPI_FLASH_BAR is not set
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_PHY_VITESSE=y
+CONFIG_PHY_GIGE=y
+CONFIG_E1000=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_DM_PCI_COMPAT=y
+CONFIG_PCIE_LAYERSCAPE=y
+CONFIG_DM_SCSI=y
+CONFIG_SYS_NS16550=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
CONFIG_FSL_ESDHC=y
CONFIG_SPI_FLASH=y
# CONFIG_SPI_FLASH_BAR is not set
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_PHYLIB=y
CONFIG_PHY_AQUANTIA=y
CONFIG_E1000=y
CONFIG_FSL_ESDHC=y
CONFIG_SPI_FLASH=y
# CONFIG_SPI_FLASH_BAR is not set
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_PHYLIB=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
CONFIG_FSL_ESDHC=y
CONFIG_SPI_FLASH=y
# CONFIG_SPI_FLASH_BAR is not set
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_PHYLIB=y
CONFIG_PHY_AQUANTIA=y
CONFIG_E1000=y
CONFIG_FSL_ESDHC=y
CONFIG_SPI_FLASH=y
# CONFIG_SPI_FLASH_BAR is not set
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_PHYLIB=y
CONFIG_PHY_AQUANTIA=y
CONFIG_E1000=y
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2007, 2010-2011 Freescale Semiconductor, Inc
+ * Copyright 2019 NXP Semiconductors
* Andy Fleming
*
* Based vaguely on the pxa mmc code:
#include <asm-generic/gpio.h>
#include <dm/pinctrl.h>
+#if !CONFIG_IS_ENABLED(BLK)
+#include "mmc_private.h"
+#endif
+
DECLARE_GLOBAL_DATA_PTR;
#define SDHCI_IRQ_EN_BITS (IRQSTATEN_CC | IRQSTATEN_TC | \
IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR | \
IRQSTATEN_DINT)
#define MAX_TUNING_LOOP 40
+#define ESDHC_DRIVER_STAGE_VALUE 0xffffffff
struct fsl_esdhc {
uint dsaddr; /* SDMA system address register */
fdt_addr_t addr;
unsigned int val;
struct mmc *mmc;
+#if !CONFIG_IS_ENABLED(BLK)
+ struct blk_desc *bdesc;
+#endif
int ret;
addr = dev_read_addr(dev);
mmc = &plat->mmc;
mmc->cfg = &plat->cfg;
mmc->dev = dev;
+#if !CONFIG_IS_ENABLED(BLK)
+ mmc->priv = priv;
+
+ /* Setup dsr related values */
+ mmc->dsr_imp = 0;
+ mmc->dsr = ESDHC_DRIVER_STAGE_VALUE;
+ /* Setup the universal parts of the block interface just once */
+ bdesc = mmc_get_blk_desc(mmc);
+ bdesc->if_type = IF_TYPE_MMC;
+ bdesc->removable = 1;
+ bdesc->devnum = mmc_get_next_devnum();
+ bdesc->block_read = mmc_bread;
+ bdesc->block_write = mmc_bwrite;
+ bdesc->block_erase = mmc_berase;
+
+ /* setup initial part type */
+ bdesc->part_type = mmc->cfg->part_type;
+ mmc_list_add(mmc);
+#endif
+
upriv->mmc = mmc;
return esdhc_init_common(priv, mmc);
#define CONFIG_FSL_SPI_INTERFACE
#define CONFIG_SF_DATAFLASH
-#define CONFIG_FSL_QSPI
#define QSPI0_AMBA_BASE 0x40000000
#define CONFIG_SPI_FLASH_SPANSION
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
#endif /* __L1028A_COMMON_H */
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2016 Freescale Semiconductor
+ * Copyright 2019 NXP
*/
#ifndef __LS1046A_COMMON_H
#include <config_distro_bootcmd.h>
#endif
+#if defined(CONFIG_TARGET_LS1046AFRWY)
+#define LS1046A_BOOT_SRC_AND_HDR\
+ "boot_scripts=ls1046afrwy_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1046afrwy_bs.out\0"
+#else
+#define LS1046A_BOOT_SRC_AND_HDR\
+ "boot_scripts=ls1046ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1046ardb_bs.out\0"
+#endif
#ifndef SPL_NO_MISC
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=ttyS0,115200\0" \
CONFIG_MTDPARTS_DEFAULT "\0" \
BOOTENV \
- "boot_scripts=ls1046ardb_boot.scr\0" \
- "boot_script_hdr=hdr_ls1046ardb_bs.out\0" \
+ LS1046A_BOOT_SRC_AND_HDR \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2019 NXP
+ */
+
+#ifndef __LS1046AFRWY_H__
+#define __LS1046AFRWY_H__
+
+#include "ls1046a_common.h"
+
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 100000000
+
+#define CONFIG_LAYERSCAPE_NS_ACCESS
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+
+#define CONFIG_SYS_UBOOT_BASE 0x40100000
+
+/* IFC */
+#define CONFIG_FSL_IFC
+/*
+ * NAND Flash Definitions
+ */
+#define CONFIG_NAND_FSL_IFC
+
+#define CONFIG_SYS_NAND_BASE 0x7e800000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_NAND \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_128 /* Spare size = 128 */ \
+ | CSOR_NAND_PB(64)) /* 64 Pages Per Block */
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x7) | \
+ FTIM0_NAND_TWH(0xa))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0xe) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \
+ FTIM2_NAND_TREH(0xa) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/* IFC Timing Params */
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+#define I2C_RETIMER_ADDR 0x18
+
+/* I2C bus multiplexer */
+#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
+#define I2C_MUX_CH_DEFAULT 0x1 /* Channel 0*/
+#define I2C_MUX_CH_RTC 0x1 /* Channel 0*/
+
+/* RTC */
+#define RTC
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 0 I2C bus 0*/
+#define CONFIG_SYS_RTC_BUS_NUM 0
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x500000 /* 5MB */
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */
+
+/* FMan */
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+
+#define QSGMII_PORT1_PHY_ADDR 0x1c
+#define QSGMII_PORT2_PHY_ADDR 0x1d
+#define QSGMII_PORT3_PHY_ADDR 0x1e
+#define QSGMII_PORT4_PHY_ADDR 0x1f
+
+#define FDT_SEQ_MACADDR_FROM_ENV
+
+#define CONFIG_ETHPRIME "FM1@DTSEC3"
+
+#endif
+
+/* QSPI device */
+#ifdef CONFIG_FSL_QSPI
+#define FSL_QSPI_FLASH_SIZE SZ_64M
+#define FSL_QSPI_FLASH_NUM 1
+#endif
+
+#undef CONFIG_BOOTCOMMAND
+#define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
+ "env exists secureboot && esbc_halt;;"
+#define SD_BOOTCOMMAND "run distro_bootcmd;run sd_bootcmd; " \
+ "env exists secureboot && esbc_halt;"
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LS1046AFRWY_H__ */
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2016 Freescale Semiconductor
+ * Copyright 2019 NXP
*/
#ifndef __LS1046ARDB_H__
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#define CONFIG_ENV_OFFSET 0x500000 /* 5MB */
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */
+#define CONFIG_SYS_FSL_QSPI_BASE 0x40000000
+#define CONFIG_ENV_ADDR CONFIG_SYS_FSL_QSPI_BASE + CONFIG_ENV_OFFSET
#else
#if defined(CONFIG_SD_BOOT)
#define CONFIG_SYS_MMC_ENV_DEV 0
/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2017 NXP
+ * Copyright 2017, 2019 NXP
* Copyright 2015 Freescale Semiconductor
*/
#else
#ifdef CONFIG_TFABOOT
#define SD_MC_INIT_CMD \
- "mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
- "mmc read 0x80100000 0x7000 0x800;" \
- "fsl_mc start mc 0x80000000 0x80100000\0"
+ "mmcinfo;mmc read 0x80a00000 0x5000 0x1200;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
#define IFC_MC_INIT_CMD \
"fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x80100000\0" \
"loadaddr_sd=0x90100000\0" \
- "kernel_addr=0x100000\0" \
- "kernel_addr_sd=0x800\0" \
+ "kernel_addr=0x581000000\0" \
+ "kernel_addr_sd=0x8000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_size_sd=0x14000\0" \
- "mcinitcmd=fsl_mc start mc 0x580a00000" \
- " 0x580e00000 \0" \
- "mcmemsize=0x70000000 \0"
+ "load_addr=0xa0000000\0" \
+ "kernelheader_addr=0x580800000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernelheader_size=0x40000\0" \
+ "BOARD=ls2088aqds\0" \
+ "mcmemsize=0x70000000 \0" \
+ IFC_MC_INIT_CMD \
+ "nor_bootcmd=echo Trying load from nor..;" \
+ "cp.b $kernel_addr $load_addr " \
+ "$kernel_size ; env exists secureboot && " \
+ "cp.b $kernelheader_addr $kernelheader_addr_r " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
+ "bootm $load_addr#$BOARD\0" \
+ "sd_bootcmd=echo Trying load from SD ..;" \
+ "mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd && " \
+ "bootm $load_addr#$BOARD\0"
#elif defined(CONFIG_SD_BOOT)
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
#endif /* CONFIG_TFABOOT */
#endif /* CONFIG_SECURE_BOOT */
+#ifdef CONFIG_TFABOOT
+#define SD_BOOTCOMMAND \
+ "env exists mcinitcmd && env exists secureboot "\
+ "&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
+ "&& esbc_validate $load_addr; " \
+ "env exists mcinitcmd && run mcinitcmd " \
+ "&& mmc read 0x80d00000 0x6800 0x800 " \
+ "&& fsl_mc lazyapply dpl 0x80d00000; " \
+ "run sd_bootcmd; " \
+ "env exists secureboot && esbc_halt;"
+
+#define IFC_NOR_BOOTCOMMAND \
+ "env exists mcinitcmd && env exists secureboot "\
+ "&& esbc_validate 0x580780000; env exists mcinitcmd "\
+ "&& fsl_mc lazyapply dpl 0x580d00000;" \
+ "run nor_bootcmd; " \
+ "env exists secureboot && esbc_halt;"
+#endif
+
#if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD)
#define CONFIG_FSL_MEMAC
#define CONFIG_PHYLIB_10G
/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2017 NXP
+ * Copyright 2017, 2019 NXP
* Copyright 2015 Freescale Semiconductor
*/
"esbc_validate 0x20740000;" \
"fsl_mc start mc 0x20a00000 0x20e00000 \0"
#define SD_MC_INIT_CMD \
- "mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
- "mmc read 0x80100000 0x7000 0x800;" \
+ "mmcinfo;mmc read 0x80a00000 0x5000 0x1200;" \
+ "mmc read 0x80e00000 0x7000 0x800;" \
"env exists secureboot && " \
"mmc read 0x80700000 0x3800 0x10 && " \
"mmc read 0x80740000 0x3A00 0x10 && " \
"esbc_validate 0x80700000 && " \
"esbc_validate 0x80740000 ;" \
- "fsl_mc start mc 0x80000000 0x80100000\0"
+ "fsl_mc start mc 0x80a00000 0x80e00000\0"
#define IFC_MC_INIT_CMD \
"env exists secureboot && " \
"esbc_validate 0x580700000 && " \
"&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
"&& esbc_validate $load_addr; " \
"env exists mcinitcmd && run mcinitcmd " \
- "&& mmc read 0x88000000 0x6800 0x800 " \
- "&& fsl_mc lazyapply dpl 0x88000000; " \
+ "&& mmc read 0x80d00000 0x6800 0x800 " \
+ "&& fsl_mc lazyapply dpl 0x80d00000; " \
"run distro_bootcmd;run sd_bootcmd; " \
"env exists secureboot && esbc_halt;"
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
- "scan_dev_for_boot=" \
- "echo Scanning ${devtype} " \
- "${devnum}:${distro_bootpart}...; " \
- "for prefix in ${boot_prefixes}; do " \
- "run scan_dev_for_scripts; " \
- "done;\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2009-2012 Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP
*/
#ifndef __FM_ETH_H__
FM_ETH_10G_E,
};
+/* Historically, on FMan v3 platforms, the first MDIO bus has been used for
+ * Clause 22 PHYs and the second MDIO bus for 10G Clause 45 PHYs (thus the
+ * TGEC name).
+ *
+ * On LS1046A-FRWY, the QSGMII PHY is connected to the second MDIO bus,
+ * and no TGEC ports are present on-board.
+ */
#ifdef CONFIG_SYS_FMAN_V3
+#ifdef CONFIG_TARGET_LS1046AFRWY
+#define CONFIG_SYS_FM1_DTSEC_MDIO_ADDR (CONFIG_SYS_FSL_FM1_ADDR + 0xfd000)
+#else
#define CONFIG_SYS_FM1_DTSEC_MDIO_ADDR (CONFIG_SYS_FSL_FM1_ADDR + 0xfc000)
+#endif
#define CONFIG_SYS_FM1_TGEC_MDIO_ADDR (CONFIG_SYS_FSL_FM1_ADDR + 0xfd000)
#if (CONFIG_SYS_NUM_FMAN == 2)
#define CONFIG_SYS_FM2_DTSEC_MDIO_ADDR (CONFIG_SYS_FSL_FM2_ADDR + 0xfc000)
projects / platform / kernel / u-boot.git / commitdiff