config ARCH_SUNXI
bool "Support sunxi (Allwinner) SoCs"
+ select DM
+ select DM_GPIO
+ select OF_CONTROL
+ select OF_SEPARATE
+ select SPL_DISABLE_OF_CONTROL
config TARGET_SNOWBALL
bool "Support snowball"
obj-y += cpu_info.o
obj-y += dram_helpers.o
obj-y += pinmux.o
-obj-y += usbc.o
+obj-y += usb_phy.o
obj-$(CONFIG_MACH_SUN6I) += prcm.o
obj-$(CONFIG_MACH_SUN8I) += prcm.o
obj-$(CONFIG_MACH_SUN9I) += prcm.o
obj-$(CONFIG_MACH_SUN8I) += clock_sun6i.o
obj-$(CONFIG_MACH_SUN9I) += clock_sun9i.o
+obj-$(CONFIG_AXP152_POWER) += pmic_bus.o
+obj-$(CONFIG_AXP209_POWER) += pmic_bus.o
+obj-$(CONFIG_AXP221_POWER) += pmic_bus.o
+
ifndef CONFIG_SPL_BUILD
ifdef CONFIG_ARMV7_PSCI
obj-y += psci.o
obj-$(CONFIG_MACH_SUN5I) += dram_sun4i.o
obj-$(CONFIG_MACH_SUN6I) += dram_sun6i.o
obj-$(CONFIG_MACH_SUN7I) += dram_sun4i.o
-obj-$(CONFIG_MACH_SUN8I) += dram_sun8i.o
+obj-$(CONFIG_MACH_SUN8I_A23) += dram_sun8i_a23.o
+obj-$(CONFIG_MACH_SUN8I_A33) += dram_sun8i_a33.o
obj-y += fel_utils.o
endif
#include <common.h>
#include <i2c.h>
-#include <netdev.h>
-#include <miiphy.h>
#include <serial.h>
#ifdef CONFIG_SPL_BUILD
#include <spl.h>
void s_init(void)
{
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
+#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_A23
/* Magic (undocmented) value taken from boot0, without this DRAM
* access gets messed up (seems cache related) */
setbits_le32(SUNXI_SRAMC_BASE + 0x44, 0x1800);
#endif
-#if !defined CONFIG_SPL_BUILD && (defined CONFIG_MACH_SUN7I || \
- defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I)
+#if defined CONFIG_MACH_SUN6I || \
+ defined CONFIG_MACH_SUN7I || \
+ defined CONFIG_MACH_SUN8I
/* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */
asm volatile(
"mrc p15, 0, r0, c1, c0, 1\n"
void reset_cpu(ulong addr)
{
-#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I)
+#ifdef CONFIG_SUNXI_GEN_SUN4I
static const struct sunxi_wdog *wdog =
&((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
/* sun5i sometimes gets stuck without this */
writel(WDT_MODE_RESET_EN | WDT_MODE_EN, &wdog->mode);
}
-#else /* CONFIG_MACH_SUN6I || CONFIG_MACH_SUN8I || .. */
+#endif
+#ifdef CONFIG_SUNXI_GEN_SUN6I
static const struct sunxi_wdog *wdog =
((struct sunxi_timer_reg *)SUNXI_TIMER_BASE)->wdog;
mdelay(200);
#endif
-#ifdef CONFIG_SUNXI_EMAC
- rc = sunxi_emac_initialize(bis);
- if (rc < 0) {
- printf("sunxi: failed to initialize emac\n");
- return rc;
- }
-#endif
-
#ifdef CONFIG_SUNXI_GMAC
rc = sunxi_gmac_initialize(bis);
if (rc < 0) {
udelay(5500);
}
+#ifdef CONFIG_MACH_SUN8I_A33
+void clock_set_pll11(unsigned int clk, bool sigma_delta_enable)
+{
+ struct sunxi_ccm_reg * const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+ if (sigma_delta_enable)
+ writel(CCM_PLL11_PATTERN, &ccm->pll5_pattern_cfg);
+
+ writel(CCM_PLL11_CTRL_EN | CCM_PLL11_CTRL_UPD |
+ (sigma_delta_enable ? CCM_PLL11_CTRL_SIGMA_DELTA_EN : 0) |
+ CCM_PLL11_CTRL_N(clk / 24000000), &ccm->pll11_cfg);
+
+ while (readl(&ccm->pll11_cfg) & CCM_PLL11_CTRL_UPD)
+ ;
+}
+#endif
+
unsigned int clock_get_pll6(void)
{
struct sunxi_ccm_reg *const ccm =
}
#elif defined CONFIG_MACH_SUN7I
puts("CPU: Allwinner A20 (SUN7I)\n");
-#elif defined CONFIG_MACH_SUN8I
+#elif defined CONFIG_MACH_SUN8I_A23
puts("CPU: Allwinner A23 (SUN8I)\n");
+#elif defined CONFIG_MACH_SUN8I_A33
+ puts("CPU: Allwinner A33 (SUN8I)\n");
#else
#warning Please update cpu_info.c with correct CPU information
puts("CPU: SUNXI Family\n");
int sunxi_get_sid(unsigned int *sid)
{
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
+#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I_A23
#ifdef CONFIG_AXP221_POWER
return axp221_get_sid(sid);
#else
--- /dev/null
+/*
+ * Sun8i a33 platform dram controller init.
+ *
+ * (C) Copyright 2007-2015 Allwinner Technology Co.
+ * Jerry Wang <wangflord@allwinnertech.com>
+ * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * (C) Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/dram.h>
+#include <asm/arch/prcm.h>
+
+/* PLL runs at 2x dram-clk, controller runs at PLL / 4 (dram-clk / 2) */
+#define DRAM_CLK_MUL 2
+#define DRAM_CLK_DIV 4
+#define DRAM_SIGMA_DELTA_ENABLE 1
+#define DRAM_ODT_EN 0
+
+struct dram_para {
+ u8 cs1;
+ u8 seq;
+ u8 bank;
+ u8 rank;
+ u8 rows;
+ u8 bus_width;
+ u16 page_size;
+};
+
+static void mctl_set_cr(struct dram_para *para)
+{
+ struct sunxi_mctl_com_reg * const mctl_com =
+ (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
+
+ writel(MCTL_CR_CS1_CONTROL(para->cs1) | MCTL_CR_UNKNOWN |
+ MCTL_CR_CHANNEL(1) | MCTL_CR_DDR3 |
+ (para->seq ? MCTL_CR_SEQUENCE : 0) |
+ ((para->bus_width == 16) ? MCTL_CR_BUSW16 : MCTL_CR_BUSW8) |
+ MCTL_CR_PAGE_SIZE(para->page_size) | MCTL_CR_ROW(para->rows) |
+ MCTL_CR_BANK(para->bank) | MCTL_CR_RANK(para->rank),
+ &mctl_com->cr);
+}
+
+static void auto_detect_dram_size(struct dram_para *para)
+{
+ u8 orig_rank = para->rank;
+ int rows, columns;
+
+ /* Row detect */
+ para->page_size = 512;
+ para->seq = 1;
+ para->rows = 16;
+ para->rank = 1;
+ mctl_set_cr(para);
+ for (rows = 11 ; rows < 16 ; rows++) {
+ if (mctl_mem_matches(1 << (rows + 9))) /* row-column */
+ break;
+ }
+
+ /* Column (page size) detect */
+ para->rows = 11;
+ para->page_size = 8192;
+ mctl_set_cr(para);
+ for (columns = 9 ; columns < 13 ; columns++) {
+ if (mctl_mem_matches(1 << columns))
+ break;
+ }
+
+ para->seq = 0;
+ para->rank = orig_rank;
+ para->rows = rows;
+ para->page_size = 1 << columns;
+ mctl_set_cr(para);
+}
+
+static inline int ns_to_t(int nanoseconds)
+{
+ const unsigned int ctrl_freq =
+ CONFIG_DRAM_CLK * DRAM_CLK_MUL / DRAM_CLK_DIV;
+
+ return (ctrl_freq * nanoseconds + 999) / 1000;
+}
+
+static void auto_set_timing_para(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+ u32 reg_val;
+
+ u8 tccd = 2;
+ u8 tfaw = ns_to_t(50);
+ u8 trrd = max(ns_to_t(10), 4);
+ u8 trcd = ns_to_t(15);
+ u8 trc = ns_to_t(53);
+ u8 txp = max(ns_to_t(8), 3);
+ u8 twtr = max(ns_to_t(8), 4);
+ u8 trtp = max(ns_to_t(8), 4);
+ u8 twr = max(ns_to_t(15), 3);
+ u8 trp = ns_to_t(15);
+ u8 tras = ns_to_t(38);
+
+ u16 trefi = ns_to_t(7800) / 32;
+ u16 trfc = ns_to_t(350);
+
+ /* Fixed timing parameters */
+ u8 tmrw = 0;
+ u8 tmrd = 4;
+ u8 tmod = 12;
+ u8 tcke = 3;
+ u8 tcksrx = 5;
+ u8 tcksre = 5;
+ u8 tckesr = 4;
+ u8 trasmax = 24;
+ u8 tcl = 6; /* CL 12 */
+ u8 tcwl = 4; /* CWL 8 */
+ u8 t_rdata_en = 4;
+ u8 wr_latency = 2;
+
+ u32 tdinit0 = (500 * CONFIG_DRAM_CLK) + 1; /* 500us */
+ u32 tdinit1 = (360 * CONFIG_DRAM_CLK) / 1000 + 1; /* 360ns */
+ u32 tdinit2 = (200 * CONFIG_DRAM_CLK) + 1; /* 200us */
+ u32 tdinit3 = (1 * CONFIG_DRAM_CLK) + 1; /* 1us */
+
+ u8 twtp = tcwl + 2 + twr; /* WL + BL / 2 + tWR */
+ u8 twr2rd = tcwl + 2 + twtr; /* WL + BL / 2 + tWTR */
+ u8 trd2wr = tcl + 2 + 1 - tcwl; /* RL + BL / 2 + 2 - WL */
+
+ /* Set work mode register */
+ mctl_set_cr(para);
+ /* Set mode register */
+ writel(MCTL_MR0, &mctl_ctl->mr0);
+ writel(MCTL_MR1, &mctl_ctl->mr1);
+ writel(MCTL_MR2, &mctl_ctl->mr2);
+ writel(MCTL_MR3, &mctl_ctl->mr3);
+ /* Set dram timing */
+ reg_val = (twtp << 24) | (tfaw << 16) | (trasmax << 8) | (tras << 0);
+ writel(reg_val, &mctl_ctl->dramtmg0);
+ reg_val = (txp << 16) | (trtp << 8) | (trc << 0);
+ writel(reg_val, &mctl_ctl->dramtmg1);
+ reg_val = (tcwl << 24) | (tcl << 16) | (trd2wr << 8) | (twr2rd << 0);
+ writel(reg_val, &mctl_ctl->dramtmg2);
+ reg_val = (tmrw << 16) | (tmrd << 12) | (tmod << 0);
+ writel(reg_val, &mctl_ctl->dramtmg3);
+ reg_val = (trcd << 24) | (tccd << 16) | (trrd << 8) | (trp << 0);
+ writel(reg_val, &mctl_ctl->dramtmg4);
+ reg_val = (tcksrx << 24) | (tcksre << 16) | (tckesr << 8) | (tcke << 0);
+ writel(reg_val, &mctl_ctl->dramtmg5);
+ /* Set two rank timing and exit self-refresh timing */
+ reg_val = readl(&mctl_ctl->dramtmg8);
+ reg_val &= ~(0xff << 8);
+ reg_val &= ~(0xff << 0);
+ reg_val |= (0x33 << 8);
+ reg_val |= (0x8 << 0);
+ writel(reg_val, &mctl_ctl->dramtmg8);
+ /* Set phy interface time */
+ reg_val = (0x2 << 24) | (t_rdata_en << 16) | (0x1 << 8)
+ | (wr_latency << 0);
+ /* PHY interface write latency and read latency configure */
+ writel(reg_val, &mctl_ctl->pitmg0);
+ /* Set phy time PTR0-2 use default */
+ writel(((tdinit0 << 0) | (tdinit1 << 20)), &mctl_ctl->ptr3);
+ writel(((tdinit2 << 0) | (tdinit3 << 20)), &mctl_ctl->ptr4);
+ /* Set refresh timing */
+ reg_val = (trefi << 16) | (trfc << 0);
+ writel(reg_val, &mctl_ctl->rfshtmg);
+}
+
+static void mctl_set_pir(u32 val)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ writel(val, &mctl_ctl->pir);
+ mctl_await_completion(&mctl_ctl->pgsr0, 0x1, 0x1);
+}
+
+static void mctl_data_train_cfg(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ if (para->rank == 2)
+ clrsetbits_le32(&mctl_ctl->dtcr, 0x3 << 24, 0x3 << 24);
+ else
+ clrsetbits_le32(&mctl_ctl->dtcr, 0x3 << 24, 0x1 << 24);
+}
+
+static int mctl_train_dram(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ mctl_data_train_cfg(para);
+ mctl_set_pir(0x1f3);
+
+ return ((readl(&mctl_ctl->pgsr0) >> 20) & 0xff) ? -EIO : 0;
+}
+
+static int mctl_channel_init(struct dram_para *para)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+ struct sunxi_mctl_com_reg * const mctl_com =
+ (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
+ u32 low_data_lines_status; /* Training status of datalines 0 - 7 */
+ u32 high_data_lines_status; /* Training status of datalines 8 - 15 */
+
+ auto_set_timing_para(para);
+
+ /* Disable dram VTC */
+ clrbits_le32(&mctl_ctl->pgcr0, 0x3f << 0);
+
+ /* Set ODT */
+ if ((CONFIG_DRAM_CLK > 400) && DRAM_ODT_EN) {
+ setbits_le32(DXnGCR0(0), 0x3 << 9);
+ setbits_le32(DXnGCR0(1), 0x3 << 9);
+ } else {
+ clrbits_le32(DXnGCR0(0), 0x3 << 9);
+ clrbits_le32(DXnGCR0(1), 0x3 << 9);
+ }
+
+ /* set PLL configuration */
+ if (CONFIG_DRAM_CLK >= 480)
+ setbits_le32(&mctl_ctl->pllgcr, 0x1 << 18);
+ else
+ setbits_le32(&mctl_ctl->pllgcr, 0x3 << 18);
+
+ /* Auto detect dram config, set 2 rank and 16bit bus-width */
+ para->cs1 = 0;
+ para->rank = 2;
+ para->bus_width = 16;
+ mctl_set_cr(para);
+
+ /* Open DQS gating */
+ clrbits_le32(&mctl_ctl->pgcr2, (0x3 << 6));
+ clrbits_le32(&mctl_ctl->dqsgmr, (0x1 << 8) | (0x7));
+
+ mctl_data_train_cfg(para);
+
+ /* ZQ calibration */
+ writel(CONFIG_DRAM_ZQ & 0xff, &mctl_ctl->zqcr1);
+ /* CA calibration */
+ mctl_set_pir(0x00000003);
+ /* More ZQ calibration */
+ writel(readl(&mctl_ctl->zqsr0) | 0x10000000, &mctl_ctl->zqcr2);
+ writel((CONFIG_DRAM_ZQ >> 8) & 0xff, &mctl_ctl->zqcr1);
+
+ /* DQS gate training */
+ if (mctl_train_dram(para) != 0) {
+ low_data_lines_status = (readl(DXnGSR0(0)) >> 24) & 0x03;
+ high_data_lines_status = (readl(DXnGSR0(1)) >> 24) & 0x03;
+
+ if (low_data_lines_status == 0x3)
+ return -EIO;
+
+ /* DRAM has only one rank */
+ para->rank = 1;
+ mctl_set_cr(para);
+
+ if (low_data_lines_status == high_data_lines_status)
+ goto done; /* 16 bit bus, 1 rank */
+
+ if (!(low_data_lines_status & high_data_lines_status)) {
+ /* Retry 16 bit bus-width with CS1 set */
+ para->cs1 = 1;
+ mctl_set_cr(para);
+ if (mctl_train_dram(para) == 0)
+ goto done;
+ }
+
+ /* Try 8 bit bus-width */
+ writel(0x0, DXnGCR0(1)); /* Disable high DQ */
+ para->cs1 = 0;
+ para->bus_width = 8;
+ mctl_set_cr(para);
+ if (mctl_train_dram(para) != 0)
+ return -EIO;
+ }
+done:
+ /* Check the dramc status */
+ mctl_await_completion(&mctl_ctl->statr, 0x1, 0x1);
+
+ /* Close DQS gating */
+ setbits_le32(&mctl_ctl->pgcr2, 0x3 << 6);
+
+ /* Enable master access */
+ writel(0xffffffff, &mctl_com->maer);
+
+ return 0;
+}
+
+static void mctl_sys_init(struct dram_para *para)
+{
+ struct sunxi_ccm_reg * const ccm =
+ (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+ struct sunxi_mctl_com_reg * const mctl_com =
+ (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
+
+ clrsetbits_le32(&ccm->dram_pll_cfg, CCM_DRAMPLL_CFG_SRC_MASK,
+ CCM_DRAMPLL_CFG_SRC_PLL11);
+
+ clock_set_pll11(CONFIG_DRAM_CLK * 1000000 * DRAM_CLK_MUL,
+ DRAM_SIGMA_DELTA_ENABLE);
+
+ clrsetbits_le32(&ccm->dram_clk_cfg, CCM_DRAMCLK_CFG_DIV_MASK,
+ CCM_DRAMCLK_CFG_DIV(DRAM_CLK_DIV) |
+ CCM_DRAMCLK_CFG_RST | CCM_DRAMCLK_CFG_UPD);
+ mctl_await_completion(&ccm->dram_clk_cfg, CCM_DRAMCLK_CFG_UPD, 0);
+
+ setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MCTL);
+ setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
+ setbits_le32(&ccm->mbus_reset, CCM_MBUS_RESET_RESET);
+ setbits_le32(&ccm->mbus0_clk_cfg, MBUS_CLK_GATE);
+
+ /* Set dram master access priority */
+ writel(0x0, &mctl_com->mapr);
+ writel(0x0f802f01, &mctl_ctl->sched);
+ writel(0x0000400f, &mctl_ctl->clken); /* normal */
+
+ udelay(250);
+}
+
+unsigned long sunxi_dram_init(void)
+{
+ struct sunxi_mctl_com_reg * const mctl_com =
+ (struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+
+ struct dram_para para = {
+ .cs1 = 0,
+ .bank = 1,
+ .rank = 1,
+ .rows = 15,
+ .bus_width = 16,
+ .page_size = 2048,
+ };
+
+ mctl_sys_init(¶);
+
+ if (mctl_channel_init(¶) != 0)
+ return 0;
+
+ auto_detect_dram_size(¶);
+
+ /* Enable master software clk */
+ writel(readl(&mctl_com->swonr) | 0x3ffff, &mctl_com->swonr);
+
+ /* Set DRAM ODT MAP */
+ if (para.rank == 2)
+ writel(0x00000303, &mctl_ctl->odtmap);
+ else
+ writel(0x00000201, &mctl_ctl->odtmap);
+
+ return para.page_size * (para.bus_width / 8) *
+ (1 << (para.bank + para.rank + para.rows));
+}
--- /dev/null
+/*
+ * (C) Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Sunxi PMIC bus access helpers
+ *
+ * The axp152 & axp209 use an i2c bus, the axp221 uses the p2wi bus and the
+ * axp223 uses the rsb bus, these functions abstract this.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/p2wi.h>
+#include <asm/arch/rsb.h>
+#include <i2c.h>
+#include <asm/arch/pmic_bus.h>
+
+#define AXP152_I2C_ADDR 0x30
+
+#define AXP209_I2C_ADDR 0x34
+
+#define AXP221_CHIP_ADDR 0x68
+#define AXP221_CTRL_ADDR 0x3e
+#define AXP221_INIT_DATA 0x3e
+
+#define AXP223_DEVICE_ADDR 0x3a3
+#define AXP223_RUNTIME_ADDR 0x2d
+
+int pmic_bus_init(void)
+{
+ /* This cannot be 0 because it is used in SPL before BSS is ready */
+ static int needs_init = 1;
+ __maybe_unused int ret;
+
+ if (!needs_init)
+ return 0;
+
+#ifdef CONFIG_AXP221_POWER
+# ifdef CONFIG_MACH_SUN6I
+ p2wi_init();
+ ret = p2wi_change_to_p2wi_mode(AXP221_CHIP_ADDR, AXP221_CTRL_ADDR,
+ AXP221_INIT_DATA);
+# else
+ ret = rsb_init();
+ if (ret)
+ return ret;
+
+ ret = rsb_set_device_address(AXP223_DEVICE_ADDR, AXP223_RUNTIME_ADDR);
+# endif
+ if (ret)
+ return ret;
+#endif
+
+ needs_init = 0;
+ return 0;
+}
+
+int pmic_bus_read(u8 reg, u8 *data)
+{
+#ifdef CONFIG_AXP152_POWER
+ return i2c_read(AXP152_I2C_ADDR, reg, 1, data, 1);
+#elif defined CONFIG_AXP209_POWER
+ return i2c_read(AXP209_I2C_ADDR, reg, 1, data, 1);
+#elif defined CONFIG_AXP221_POWER
+# ifdef CONFIG_MACH_SUN6I
+ return p2wi_read(reg, data);
+# else
+ return rsb_read(AXP223_RUNTIME_ADDR, reg, data);
+# endif
+#endif
+}
+
+int pmic_bus_write(u8 reg, u8 data)
+{
+#ifdef CONFIG_AXP152_POWER
+ return i2c_write(AXP152_I2C_ADDR, reg, 1, &data, 1);
+#elif defined CONFIG_AXP209_POWER
+ return i2c_write(AXP209_I2C_ADDR, reg, 1, &data, 1);
+#elif defined CONFIG_AXP221_POWER
+# ifdef CONFIG_MACH_SUN6I
+ return p2wi_write(reg, data);
+# else
+ return rsb_write(AXP223_RUNTIME_ADDR, reg, data);
+# endif
+#endif
+}
+
+int pmic_bus_setbits(u8 reg, u8 bits)
+{
+ int ret;
+ u8 val;
+
+ ret = pmic_bus_read(reg, &val);
+ if (ret)
+ return ret;
+
+ val |= bits;
+ return pmic_bus_write(reg, val);
+}
+
+int pmic_bus_clrbits(u8 reg, u8 bits)
+{
+ int ret;
+ u8 val;
+
+ ret = pmic_bus_read(reg, &val);
+ if (ret)
+ return ret;
+
+ val &= ~bits;
+ return pmic_bus_write(reg, val);
+}
isb
bl _nonsec_init
- bl psci_arch_init
adr r0, _target_pc
ldr r0, [r0]
--- /dev/null
+/*
+ * Sunxi usb-phy code
+ *
+ * Copyright (C) 2015 Hans de Goede <hdegoede@redhat.com>
+ * Copyright (C) 2014 Roman Byshko <rbyshko@gmail.com>
+ *
+ * Based on code from
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/usb_phy.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <errno.h>
+#ifdef CONFIG_AXP152_POWER
+#include <axp152.h>
+#endif
+#ifdef CONFIG_AXP209_POWER
+#include <axp209.h>
+#endif
+#ifdef CONFIG_AXP221_POWER
+#include <axp221.h>
+#endif
+
+#define SUNXI_USB_PMU_IRQ_ENABLE 0x800
+#ifdef CONFIG_MACH_SUN8I_A33
+#define SUNXI_USB_CSR 0x410
+#else
+#define SUNXI_USB_CSR 0x404
+#endif
+#define SUNXI_USB_PASSBY_EN 1
+
+#define SUNXI_EHCI_AHB_ICHR8_EN (1 << 10)
+#define SUNXI_EHCI_AHB_INCR4_BURST_EN (1 << 9)
+#define SUNXI_EHCI_AHB_INCRX_ALIGN_EN (1 << 8)
+#define SUNXI_EHCI_ULPI_BYPASS_EN (1 << 0)
+
+static struct sunxi_usb_phy {
+ int usb_rst_mask;
+ int gpio_vbus;
+ int gpio_vbus_det;
+ int id;
+ int init_count;
+ int power_on_count;
+} sunxi_usb_phy[] = {
+ {
+ .usb_rst_mask = CCM_USB_CTRL_PHY0_RST | CCM_USB_CTRL_PHY0_CLK,
+ .id = 0,
+ },
+ {
+ .usb_rst_mask = CCM_USB_CTRL_PHY1_RST | CCM_USB_CTRL_PHY1_CLK,
+ .id = 1,
+ },
+#if CONFIG_SUNXI_USB_PHYS >= 3
+ {
+ .usb_rst_mask = CCM_USB_CTRL_PHY2_RST | CCM_USB_CTRL_PHY2_CLK,
+ .id = 2,
+ }
+#endif
+};
+
+static int get_vbus_gpio(int index)
+{
+ switch (index) {
+ case 0: return sunxi_name_to_gpio(CONFIG_USB0_VBUS_PIN);
+ case 1: return sunxi_name_to_gpio(CONFIG_USB1_VBUS_PIN);
+ case 2: return sunxi_name_to_gpio(CONFIG_USB2_VBUS_PIN);
+ }
+ return -EINVAL;
+}
+
+static int get_vbus_detect_gpio(int index)
+{
+ switch (index) {
+ case 0: return sunxi_name_to_gpio(CONFIG_USB0_VBUS_DET);
+ }
+ return -EINVAL;
+}
+
+static void usb_phy_write(struct sunxi_usb_phy *phy, int addr,
+ int data, int len)
+{
+ int j = 0, usbc_bit = 0;
+ void *dest = (void *)SUNXI_USB0_BASE + SUNXI_USB_CSR;
+
+#ifdef CONFIG_MACH_SUN8I_A33
+ /* CSR needs to be explicitly initialized to 0 on A33 */
+ writel(0, dest);
+#endif
+
+ usbc_bit = 1 << (phy->id * 2);
+ for (j = 0; j < len; j++) {
+ /* set the bit address to be written */
+ clrbits_le32(dest, 0xff << 8);
+ setbits_le32(dest, (addr + j) << 8);
+
+ clrbits_le32(dest, usbc_bit);
+ /* set data bit */
+ if (data & 0x1)
+ setbits_le32(dest, 1 << 7);
+ else
+ clrbits_le32(dest, 1 << 7);
+
+ setbits_le32(dest, usbc_bit);
+
+ clrbits_le32(dest, usbc_bit);
+
+ data >>= 1;
+ }
+}
+
+static void sunxi_usb_phy_config(struct sunxi_usb_phy *phy)
+{
+ /* The following comments are machine
+ * translated from Chinese, you have been warned!
+ */
+
+ /* Regulation 45 ohms */
+ if (phy->id == 0)
+ usb_phy_write(phy, 0x0c, 0x01, 1);
+
+ /* adjust PHY's magnitude and rate */
+ usb_phy_write(phy, 0x20, 0x14, 5);
+
+ /* threshold adjustment disconnect */
+#if defined CONFIG_MACH_SUN4I || defined CONFIG_MACH_SUN6I
+ usb_phy_write(phy, 0x2a, 3, 2);
+#else
+ usb_phy_write(phy, 0x2a, 2, 2);
+#endif
+
+ return;
+}
+
+static void sunxi_usb_phy_passby(int index, int enable)
+{
+ unsigned long bits = 0;
+ void *addr;
+
+ if (index == 1)
+ addr = (void *)SUNXI_USB1_BASE + SUNXI_USB_PMU_IRQ_ENABLE;
+ else
+ addr = (void *)SUNXI_USB2_BASE + SUNXI_USB_PMU_IRQ_ENABLE;
+
+ bits = SUNXI_EHCI_AHB_ICHR8_EN |
+ SUNXI_EHCI_AHB_INCR4_BURST_EN |
+ SUNXI_EHCI_AHB_INCRX_ALIGN_EN |
+ SUNXI_EHCI_ULPI_BYPASS_EN;
+
+ if (enable)
+ setbits_le32(addr, bits);
+ else
+ clrbits_le32(addr, bits);
+
+ return;
+}
+
+void sunxi_usb_phy_enable_squelch_detect(int index, int enable)
+{
+ struct sunxi_usb_phy *phy = &sunxi_usb_phy[index];
+
+ usb_phy_write(phy, 0x3c, enable ? 0 : 2, 2);
+}
+
+void sunxi_usb_phy_init(int index)
+{
+ struct sunxi_usb_phy *phy = &sunxi_usb_phy[index];
+ struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+ phy->init_count++;
+ if (phy->init_count != 1)
+ return;
+
+ setbits_le32(&ccm->usb_clk_cfg, phy->usb_rst_mask);
+
+ sunxi_usb_phy_config(phy);
+
+ if (phy->id != 0)
+ sunxi_usb_phy_passby(index, SUNXI_USB_PASSBY_EN);
+}
+
+void sunxi_usb_phy_exit(int index)
+{
+ struct sunxi_usb_phy *phy = &sunxi_usb_phy[index];
+ struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
+ phy->init_count--;
+ if (phy->init_count != 0)
+ return;
+
+ if (phy->id != 0)
+ sunxi_usb_phy_passby(index, !SUNXI_USB_PASSBY_EN);
+
+ clrbits_le32(&ccm->usb_clk_cfg, phy->usb_rst_mask);
+}
+
+void sunxi_usb_phy_power_on(int index)
+{
+ struct sunxi_usb_phy *phy = &sunxi_usb_phy[index];
+
+ phy->power_on_count++;
+ if (phy->power_on_count != 1)
+ return;
+
+ if (phy->gpio_vbus >= 0)
+ gpio_set_value(phy->gpio_vbus, 1);
+}
+
+void sunxi_usb_phy_power_off(int index)
+{
+ struct sunxi_usb_phy *phy = &sunxi_usb_phy[index];
+
+ phy->power_on_count--;
+ if (phy->power_on_count != 0)
+ return;
+
+ if (phy->gpio_vbus >= 0)
+ gpio_set_value(phy->gpio_vbus, 0);
+}
+
+int sunxi_usb_phy_vbus_detect(int index)
+{
+ struct sunxi_usb_phy *phy = &sunxi_usb_phy[index];
+ int err, retries = 3;
+
+ if (phy->gpio_vbus_det < 0) {
+ eprintf("Error: invalid vbus detection pin\n");
+ return phy->gpio_vbus_det;
+ }
+
+ err = gpio_get_value(phy->gpio_vbus_det);
+ /*
+ * Vbus may have been provided by the board and just been turned of
+ * some milliseconds ago on reset, what we're measuring then is a
+ * residual charge on Vbus, sleep a bit and try again.
+ */
+ while (err > 0 && retries--) {
+ mdelay(100);
+ err = gpio_get_value(phy->gpio_vbus_det);
+ }
+
+ return err;
+}
+
+int sunxi_usb_phy_probe(void)
+{
+ struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ struct sunxi_usb_phy *phy;
+ int i, ret = 0;
+
+ for (i = 0; i < CONFIG_SUNXI_USB_PHYS; i++) {
+ phy = &sunxi_usb_phy[i];
+
+ phy->gpio_vbus = get_vbus_gpio(i);
+ if (phy->gpio_vbus >= 0) {
+ ret = gpio_request(phy->gpio_vbus, "usb_vbus");
+ if (ret)
+ return ret;
+ ret = gpio_direction_output(phy->gpio_vbus, 0);
+ if (ret)
+ return ret;
+ }
+
+ phy->gpio_vbus_det = get_vbus_detect_gpio(i);
+ if (phy->gpio_vbus_det >= 0) {
+ ret = gpio_request(phy->gpio_vbus_det, "usb_vbus_det");
+ if (ret)
+ return ret;
+ ret = gpio_direction_input(phy->gpio_vbus_det);
+ if (ret)
+ return ret;
+ }
+ }
+
+ setbits_le32(&ccm->usb_clk_cfg, CCM_USB_CTRL_PHYGATE);
+
+ return 0;
+}
+
+int sunxi_usb_phy_remove(void)
+{
+ struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ struct sunxi_usb_phy *phy;
+ int i;
+
+ clrbits_le32(&ccm->usb_clk_cfg, CCM_USB_CTRL_PHYGATE);
+
+ for (i = 0; i < CONFIG_SUNXI_USB_PHYS; i++) {
+ phy = &sunxi_usb_phy[i];
+
+ if (phy->gpio_vbus >= 0)
+ gpio_free(phy->gpio_vbus);
+
+ if (phy->gpio_vbus_det >= 0)
+ gpio_free(phy->gpio_vbus_det);
+ }
+
+ return 0;
+}
+++ /dev/null
-/*
- * Sunxi usb-controller code shared between the ehci and musb controllers
- *
- * Copyright (C) 2014 Roman Byshko
- *
- * Roman Byshko <rbyshko@gmail.com>
- *
- * Based on code from
- * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <asm/arch/clock.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/usbc.h>
-#include <asm/gpio.h>
-#include <asm/io.h>
-#include <common.h>
-#ifdef CONFIG_AXP152_POWER
-#include <axp152.h>
-#endif
-#ifdef CONFIG_AXP209_POWER
-#include <axp209.h>
-#endif
-#ifdef CONFIG_AXP221_POWER
-#include <axp221.h>
-#endif
-
-#define SUNXI_USB_PMU_IRQ_ENABLE 0x800
-#define SUNXI_USB_CSR 0x404
-#define SUNXI_USB_PASSBY_EN 1
-
-#define SUNXI_EHCI_AHB_ICHR8_EN (1 << 10)
-#define SUNXI_EHCI_AHB_INCR4_BURST_EN (1 << 9)
-#define SUNXI_EHCI_AHB_INCRX_ALIGN_EN (1 << 8)
-#define SUNXI_EHCI_ULPI_BYPASS_EN (1 << 0)
-
-static struct sunxi_usbc_hcd {
- struct usb_hcd *hcd;
- int usb_rst_mask;
- int ahb_clk_mask;
- int gpio_vbus;
- int gpio_vbus_det;
- int irq;
- int id;
-} sunxi_usbc_hcd[] = {
- {
- .usb_rst_mask = CCM_USB_CTRL_PHY0_RST | CCM_USB_CTRL_PHY0_CLK,
- .ahb_clk_mask = 1 << AHB_GATE_OFFSET_USB0,
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
- .irq = 71,
-#else
- .irq = 38,
-#endif
- .id = 0,
- },
- {
- .usb_rst_mask = CCM_USB_CTRL_PHY1_RST | CCM_USB_CTRL_PHY1_CLK,
- .ahb_clk_mask = 1 << AHB_GATE_OFFSET_USB_EHCI0,
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
- .irq = 72,
-#else
- .irq = 39,
-#endif
- .id = 1,
- },
-#if (CONFIG_USB_MAX_CONTROLLER_COUNT > 1)
- {
- .usb_rst_mask = CCM_USB_CTRL_PHY2_RST | CCM_USB_CTRL_PHY2_CLK,
- .ahb_clk_mask = 1 << AHB_GATE_OFFSET_USB_EHCI1,
-#ifdef CONFIG_MACH_SUN6I
- .irq = 74,
-#else
- .irq = 40,
-#endif
- .id = 2,
- }
-#endif
-};
-
-static int enabled_hcd_count;
-
-void *sunxi_usbc_get_io_base(int index)
-{
- switch (index) {
- case 0:
- return (void *)SUNXI_USB0_BASE;
- case 1:
- return (void *)SUNXI_USB1_BASE;
- case 2:
- return (void *)SUNXI_USB2_BASE;
- default:
- return NULL;
- }
-}
-
-static int get_vbus_gpio(int index)
-{
- switch (index) {
- case 0: return sunxi_name_to_gpio(CONFIG_USB0_VBUS_PIN);
- case 1: return sunxi_name_to_gpio(CONFIG_USB1_VBUS_PIN);
- case 2: return sunxi_name_to_gpio(CONFIG_USB2_VBUS_PIN);
- }
- return -1;
-}
-
-static int get_vbus_detect_gpio(int index)
-{
- switch (index) {
- case 0: return sunxi_name_to_gpio(CONFIG_USB0_VBUS_DET);
- }
- return -1;
-}
-
-static void usb_phy_write(struct sunxi_usbc_hcd *sunxi_usbc, int addr,
- int data, int len)
-{
- int j = 0, usbc_bit = 0;
- void *dest = sunxi_usbc_get_io_base(0) + SUNXI_USB_CSR;
-
- usbc_bit = 1 << (sunxi_usbc->id * 2);
- for (j = 0; j < len; j++) {
- /* set the bit address to be written */
- clrbits_le32(dest, 0xff << 8);
- setbits_le32(dest, (addr + j) << 8);
-
- clrbits_le32(dest, usbc_bit);
- /* set data bit */
- if (data & 0x1)
- setbits_le32(dest, 1 << 7);
- else
- clrbits_le32(dest, 1 << 7);
-
- setbits_le32(dest, usbc_bit);
-
- clrbits_le32(dest, usbc_bit);
-
- data >>= 1;
- }
-}
-
-static void sunxi_usb_phy_init(struct sunxi_usbc_hcd *sunxi_usbc)
-{
- /* The following comments are machine
- * translated from Chinese, you have been warned!
- */
-
- /* Regulation 45 ohms */
- if (sunxi_usbc->id == 0)
- usb_phy_write(sunxi_usbc, 0x0c, 0x01, 1);
-
- /* adjust PHY's magnitude and rate */
- usb_phy_write(sunxi_usbc, 0x20, 0x14, 5);
-
- /* threshold adjustment disconnect */
-#if defined CONFIG_MACH_SUN4I || defined CONFIG_MACH_SUN6I
- usb_phy_write(sunxi_usbc, 0x2a, 3, 2);
-#else
- usb_phy_write(sunxi_usbc, 0x2a, 2, 2);
-#endif
-
- return;
-}
-
-static void sunxi_usb_passby(struct sunxi_usbc_hcd *sunxi_usbc, int enable)
-{
- unsigned long bits = 0;
- void *addr = sunxi_usbc_get_io_base(sunxi_usbc->id) +
- SUNXI_USB_PMU_IRQ_ENABLE;
-
- bits = SUNXI_EHCI_AHB_ICHR8_EN |
- SUNXI_EHCI_AHB_INCR4_BURST_EN |
- SUNXI_EHCI_AHB_INCRX_ALIGN_EN |
- SUNXI_EHCI_ULPI_BYPASS_EN;
-
- if (enable)
- setbits_le32(addr, bits);
- else
- clrbits_le32(addr, bits);
-
- return;
-}
-
-void sunxi_usbc_enable_squelch_detect(int index, int enable)
-{
- struct sunxi_usbc_hcd *sunxi_usbc = &sunxi_usbc_hcd[index];
-
- usb_phy_write(sunxi_usbc, 0x3c, enable ? 0 : 2, 2);
-}
-
-int sunxi_usbc_request_resources(int index)
-{
- struct sunxi_usbc_hcd *sunxi_usbc = &sunxi_usbc_hcd[index];
- int ret = 0;
-
- sunxi_usbc->gpio_vbus = get_vbus_gpio(index);
- if (sunxi_usbc->gpio_vbus != -1) {
- ret |= gpio_request(sunxi_usbc->gpio_vbus, "usbc_vbus");
- ret |= gpio_direction_output(sunxi_usbc->gpio_vbus, 0);
- }
-
- sunxi_usbc->gpio_vbus_det = get_vbus_detect_gpio(index);
- if (sunxi_usbc->gpio_vbus_det != -1) {
- ret |= gpio_request(sunxi_usbc->gpio_vbus_det, "usbc_vbus_det");
- ret |= gpio_direction_input(sunxi_usbc->gpio_vbus_det);
- }
-
- return ret;
-}
-
-int sunxi_usbc_free_resources(int index)
-{
- struct sunxi_usbc_hcd *sunxi_usbc = &sunxi_usbc_hcd[index];
- int ret = 0;
-
- if (sunxi_usbc->gpio_vbus != -1)
- ret |= gpio_free(sunxi_usbc->gpio_vbus);
-
- if (sunxi_usbc->gpio_vbus_det != -1)
- ret |= gpio_free(sunxi_usbc->gpio_vbus_det);
-
- return ret;
-}
-
-void sunxi_usbc_enable(int index)
-{
- struct sunxi_usbc_hcd *sunxi_usbc = &sunxi_usbc_hcd[index];
- struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
-
- /* enable common PHY only once */
- if (enabled_hcd_count == 0)
- setbits_le32(&ccm->usb_clk_cfg, CCM_USB_CTRL_PHYGATE);
-
- setbits_le32(&ccm->usb_clk_cfg, sunxi_usbc->usb_rst_mask);
- setbits_le32(&ccm->ahb_gate0, sunxi_usbc->ahb_clk_mask);
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
- setbits_le32(&ccm->ahb_reset0_cfg, sunxi_usbc->ahb_clk_mask);
-#endif
-
- sunxi_usb_phy_init(sunxi_usbc);
-
- if (sunxi_usbc->id != 0)
- sunxi_usb_passby(sunxi_usbc, SUNXI_USB_PASSBY_EN);
-
- enabled_hcd_count++;
-}
-
-void sunxi_usbc_disable(int index)
-{
- struct sunxi_usbc_hcd *sunxi_usbc = &sunxi_usbc_hcd[index];
- struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
-
- if (sunxi_usbc->id != 0)
- sunxi_usb_passby(sunxi_usbc, !SUNXI_USB_PASSBY_EN);
-
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
- clrbits_le32(&ccm->ahb_reset0_cfg, sunxi_usbc->ahb_clk_mask);
-#endif
- clrbits_le32(&ccm->ahb_gate0, sunxi_usbc->ahb_clk_mask);
- clrbits_le32(&ccm->usb_clk_cfg, sunxi_usbc->usb_rst_mask);
-
- /* disable common PHY only once, for the last enabled hcd */
- if (enabled_hcd_count == 1)
- clrbits_le32(&ccm->usb_clk_cfg, CCM_USB_CTRL_PHYGATE);
-
- enabled_hcd_count--;
-}
-
-void sunxi_usbc_vbus_enable(int index)
-{
- struct sunxi_usbc_hcd *sunxi_usbc = &sunxi_usbc_hcd[index];
-
- if (sunxi_usbc->gpio_vbus != -1)
- gpio_set_value(sunxi_usbc->gpio_vbus, 1);
-}
-
-void sunxi_usbc_vbus_disable(int index)
-{
- struct sunxi_usbc_hcd *sunxi_usbc = &sunxi_usbc_hcd[index];
-
- if (sunxi_usbc->gpio_vbus != -1)
- gpio_set_value(sunxi_usbc->gpio_vbus, 0);
-}
-
-int sunxi_usbc_vbus_detect(int index)
-{
- struct sunxi_usbc_hcd *sunxi_usbc = &sunxi_usbc_hcd[index];
- int err, retries = 3;
-
- if (sunxi_usbc->gpio_vbus_det == -1) {
- eprintf("Error: invalid vbus detection pin\n");
- return -1;
- }
-
- err = gpio_get_value(sunxi_usbc->gpio_vbus_det);
- /*
- * Vbus may have been provided by the board and just been turned of
- * some milliseconds ago on reset, what we're measuring then is a
- * residual charge on Vbus, sleep a bit and try again.
- */
- while (err > 0 && retries--) {
- mdelay(100);
- err = gpio_get_value(sunxi_usbc->gpio_vbus_det);
- }
-
- return err;
-}
-dtb-$(CONFIG_MACH_SUN7I) += sun7i-a20-pcduino3.dtb
dtb-$(CONFIG_S5PC100) += s5pc1xx-smdkc100.dtb
dtb-$(CONFIG_S5PC110) += s5pc1xx-goni.dtb
dtb-$(CONFIG_EXYNOS4) += exynos4210-origen.dtb \
dtb-$(CONFIG_LS102XA) += ls1021a-qds.dtb \
ls1021a-twr.dtb
+dtb-$(CONFIG_MACH_SUN4I) += \
+ sun4i-a10-a1000.dtb \
+ sun4i-a10-ba10-tvbox.dtb \
+ sun4i-a10-chuwi-v7-cw0825.dtb \
+ sun4i-a10-cubieboard.dtb \
+ sun4i-a10-gemei-g9.dtb \
+ sun4i-a10-hackberry.dtb \
+ sun4i-a10-hyundai-a7hd.dtb \
+ sun4i-a10-inet-3f.dtb \
+ sun4i-a10-inet-3w.dtb \
+ sun4i-a10-inet97fv2.dtb \
+ sun4i-a10-jesurun-q5.dtb \
+ sun4i-a10-marsboard.dtb \
+ sun4i-a10-mini-xplus.dtb \
+ sun4i-a10-mk802.dtb \
+ sun4i-a10-mk802ii.dtb \
+ sun4i-a10-olinuxino-lime.dtb \
+ sun4i-a10-pcduino.dtb
+dtb-$(CONFIG_MACH_SUN5I) += \
+ sun5i-a10s-auxtek-t004.dtb \
+ sun5i-a10s-mk802.dtb \
+ sun5i-a10s-olinuxino-micro.dtb \
+ sun5i-a10s-r7-tv-dongle.dtb \
+ sun5i-a13-ampe-a76.dtb \
+ sun5i-a13-forfun-q88db.dtb \
+ sun5i-a13-hsg-h702.dtb \
+ sun5i-a13-inet-86vs.dtb \
+ sun5i-a13-olinuxino.dtb \
+ sun5i-a13-olinuxino-micro.dtb \
+ sun5i-a13-tzx-q8-713b7.dtb \
+ sun5i-a13-utoo-p66.dtb
+dtb-$(CONFIG_MACH_SUN6I) += \
+ sun6i-a31-app4-evb1.dtb \
+ sun6i-a31-colombus.dtb \
+ sun6i-a31-hummingbird.dtb \
+ sun6i-a31-i7.dtb \
+ sun6i-a31-m9.dtb \
+ sun6i-a31-mixtile-loftq.dtb \
+ sun6i-a31s-cs908.dtb \
+ sun6i-a31s-primo81.dtb
+dtb-$(CONFIG_MACH_SUN7I) += \
+ sun7i-a20-ainol-aw1.dtb \
+ sun7i-a20-bananapi.dtb \
+ sun7i-a20-bananapro.dtb \
+ sun7i-a20-cubieboard2.dtb \
+ sun7i-a20-cubietruck.dtb \
+ sun7i-a20-hummingbird.dtb \
+ sun7i-a20-i12-tvbox.dtb \
+ sun7i-a20-m3.dtb \
+ sun7i-a20-m5.dtb \
+ sun7i-a20-mk808c.dtb \
+ sun7i-a20-olinuxino-lime.dtb \
+ sun7i-a20-olinuxino-lime2.dtb \
+ sun7i-a20-olinuxino-micro.dtb \
+ sun7i-a20-orangepi.dtb \
+ sun7i-a20-orangepi-mini.dtb \
+ sun7i-a20-pcduino3.dtb \
+ sun7i-a20-pcduino3-nano.dtb \
+ sun7i-a20-primo73.dtb \
+ sun7i-a20-wexler-tab7200.dtb \
+ sun7i-a20-wits-pro-a20-dkt.dtb \
+ sun7i-a20-yones-toptech-bd1078.dtb
+dtb-$(CONFIG_MACH_SUN8I_A23) += \
+ sun8i-a23-ippo-q8h-v5.dtb \
+ sun8i-a23-ippo-q8h-v1.2.dtb
+dtb-$(CONFIG_MACH_SUN8I_A33) += \
+ sun8i-a33-astar-mid756.dtb \
+ sun8i-a33-ippo-q8h-v1.2-lcd1024x600.dtb
+dtb-$(CONFIG_MACH_SUN9I) += \
+ sun9i-a80-optimus.dtb \
+ sun9i-a80-cubieboard4.dtb
+
targets += $(dtb-y)
DTC_FLAGS += -R 4 -p 0x1000
--- /dev/null
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * AXP202/209 Integrated Power Management Chip
+ * http://www.x-powers.com/product/AXP20X.php
+ * http://dl.linux-sunxi.org/AXP/AXP209%20Datasheet%20v1.0_cn.pdf
+ */
+
+&axp209 {
+ compatible = "x-powers,axp209";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ regulators {
+ /* Default work frequency for buck regulators */
+ x-powers,dcdc-freq = <1500>;
+
+ reg_dcdc2: dcdc2 {
+ regulator-name = "dcdc2";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-name = "dcdc3";
+ };
+
+ reg_ldo1: ldo1 {
+ /* LDO1 is a fixed output regulator */
+ regulator-always-on;
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "ldo1";
+ };
+
+ reg_ldo2: ldo2 {
+ regulator-name = "ldo2";
+ };
+
+ reg_ldo3: ldo3 {
+ regulator-name = "ldo3";
+ };
+
+ reg_ldo4: ldo4 {
+ regulator-name = "ldo4";
+ };
+
+ reg_ldo5: ldo5 {
+ regulator-name = "ldo5";
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2013 Emilio López
+ *
+ * Emilio López <emilio@elopez.com.ar>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Mele A1000";
+ compatible = "mele,a1000", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_a1000>;
+
+ red {
+ label = "a1000:red:usr";
+ gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "a1000:blue:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_emac_3v3: emac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_power_pin_a1000>;
+ regulator-name = "emac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ phy-supply = <®_emac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ emac_power_pin_a1000: emac_power_pin@0 {
+ allwinner,pins = "PH15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_a1000: led_pins@0 {
+ allwinner,pins = "PH10", "PH20";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "BA10 tvbox";
+ compatible = "allwinner,ba10-tvbox", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ usb2_vbus_pin_a: usb2_vbus_pin@0 {
+ allwinner,pins = "PH12";
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Chuwi V7 CW0825";
+ compatible = "chuwi,v7-cw0825", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@800 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <800000>;
+ };
+
+ button@1000 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <1000000>;
+ };
+
+ button@1200 {
+ label = "Back";
+ linux,code = <KEY_BACK>;
+ channel = <0>;
+ voltage = <1200000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2012 Stefan Roese
+ * Stefan Roese <sr@denx.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Cubietech Cubieboard";
+ compatible = "cubietech,a10-cubieboard", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_cubieboard>;
+
+ blue {
+ label = "cubieboard:blue:usr";
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* LED1 */
+ };
+
+ green {
+ label = "cubieboard:green:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* LED2 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ led_pins_cubieboard: led_pins@0 {
+ allwinner,pins = "PH20", "PH21";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Priit Laes
+ *
+ * Priit Laes <plaes@plaes.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Gemei G9 Tablet";
+ compatible = "gemei,g9", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+/*
+ * TODO:
+ * 2x cameras via CSI
+ * bma250 IRQs
+ * AXP battery management
+ * NAND
+ * OTG
+ * Touchscreen - gt801_2plus1 @ i2c adapter 2 @ 0x48
+ */
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ /* Accelerometer */
+ bma250@18 {
+ compatible = "bosch,bma250";
+ reg = <0x18>;
+
+ /*
+ * TODO: interrupt pins:
+ * int1 - PH00
+ * int2 - PI10
+ */
+ };
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+
+ status = "okay";
+
+ button@158 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <158730>;
+ };
+
+ button@349 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <349206>;
+ };
+
+ button@1142 {
+ label = "Esc";
+ linux,code = <KEY_ESC>;
+ channel = <0>;
+ voltage = <1142856>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH01 */
+ cd-inverted;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2012 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Miniand Hackberry";
+ compatible = "miniand,hackberry", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_emac_3v3: emac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "emac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy0>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ phy-supply = <®_emac_3v3>;
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hackberry_hogs>;
+
+ hackberry_hogs: hogs@0 {
+ allwinner,pins = "PH19";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb2_vbus_pin_hackberry: usb2_vbus_pin@0 {
+ allwinner,pins = "PH12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin_hackberry>;
+ gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Hyundai A7HD";
+ compatible = "hyundai,a7hd", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+®_usb2_vbus {
+ gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb2_vbus_pin_a {
+ allwinner,pins = "PH6";
+};
+
+&usbphy {
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the iNet 3F for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+
+/ {
+ model = "iNet 3F";
+ compatible = "inet,3f", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the iNet 3W for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+
+/ {
+ model = "iNet 3W";
+ compatible = "inet,3w", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Open Source Support GmbH
+ *
+ * David Lanzendörfer <david.lanzendoerfer@o2s.ch>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "INet-97F Rev 02";
+ compatible = "primux,inet97fv2", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Gábor Nyers
+ *
+ * Gábor Nyers <gabor.nyers@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Jesurun Q5";
+ compatible = "jesurun,q5", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_q5>;
+
+ green {
+ label = "q5:green:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+ };
+
+ };
+
+ reg_emac_3v3: emac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_power_pin_q5>;
+ regulator-name = "emac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ phy-supply = <®_emac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ emac_power_pin_q5: emac_power_pin@0 {
+ allwinner,pins = "PH19";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_q5: led_pins@0 {
+ allwinner,pins = "PH20";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Aleksei Mamlin
+ * Aleksei Mamlin <mamlinav@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "HAOYU Electronics Marsboard A10";
+ compatible = "haoyu,a10-marsboard", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_marsboard>;
+
+ red1 {
+ label = "marsboard:red1:usr";
+ gpios = <&pio 1 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ red2 {
+ label = "marsboard:red2:usr";
+ gpios = <&pio 1 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ red3 {
+ label = "marsboard:red3:usr";
+ gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ red4 {
+ label = "marsboard:red4:usr";
+ gpios = <&pio 1 8 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ led_pins_marsboard: led_pins@0 {
+ allwinner,pins = "PB5", "PB6", "PB7", "PB8";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2012 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "PineRiver Mini X-Plus";
+ compatible = "pineriver,mini-xplus", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&ir0_pins_a {
+ /* The ir receiver is not always populated */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "MK802";
+ compatible = "allwinner,mk802", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ usb2_vbus_pin_mk802: usb2_vbus_pin@0 {
+ allwinner,pins = "PH12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin_mk802>;
+ gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "MK802ii";
+ compatible = "allwinner,mk802ii", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 - Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Olimex A10-OLinuXino-LIME";
+ compatible = "olimex,a10-olinuxino-lime", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxinolime>;
+
+ green {
+ label = "a10-olinuxino-lime:green:usr";
+ gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ /*
+ * The A10-Lime is known to be unstable when running at 1008 MHz
+ */
+ operating-points = <
+ /* kHz uV */
+ 912000 1350000
+ 864000 1300000
+ 624000 1250000
+ >;
+ cooling-max-level = <2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 {
+ allwinner,pins = "PC3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_olinuxinolime: led_pins@0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
+ gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Zoltan HERPAI
+ * Zoltan HERPAI <wigyori@uid0.hu>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun4i-a10.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "LinkSprite pcDuino";
+ compatible = "linksprite,a10-pcduino", "allwinner,sun4i-a10";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_pcduino>;
+
+ tx {
+ label = "pcduino:green:tx";
+ gpios = <&pio 7 15 GPIO_ACTIVE_LOW>;
+ };
+
+ rx {
+ label = "pcduino:green:rx";
+ gpios = <&pio 7 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&key_pins_pcduino>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ button@0 {
+ label = "Key Back";
+ linux,code = <KEY_BACK>;
+ gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
+ };
+
+ button@1 {
+ label = "Key Home";
+ linux,code = <KEY_HOME>;
+ gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
+ };
+
+ button@2 {
+ label = "Key Menu";
+ linux,code = <KEY_MENU>;
+ gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ led_pins_pcduino: led_pins@0 {
+ allwinner,pins = "PH15", "PH16";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ key_pins_pcduino: key_pins@0 {
+ allwinner,pins = "PH17", "PH18", "PH19";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2012 Stefan Roese
+ * Stefan Roese <sr@denx.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/thermal/thermal.h>
+
+#include <dt-bindings/dma/sun4i-a10.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ aliases {
+ ethernet0 = &emac;
+ };
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@0 {
+ compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0-hdmi";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>;
+ status = "disabled";
+ };
+
+ framebuffer@1 {
+ compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
+ allwinner,pipeline = "de_fe0-de_be0-lcd0-hdmi";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>, <&ahb_gates 46>;
+ status = "disabled";
+ };
+
+ framebuffer@2 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_fe0-de_be0-lcd0";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>,
+ <&ahb_gates 46>;
+ status = "disabled";
+ };
+
+ framebuffer@3 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_fe0-de_be0-lcd0-tve0";
+ clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
+ <&ahb_gates 44>, <&ahb_gates 46>;
+ status = "disabled";
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a8";
+ reg = <0x0>;
+ clocks = <&cpu>;
+ clock-latency = <244144>; /* 8 32k periods */
+ operating-points = <
+ /* kHz uV */
+ 1008000 1400000
+ 912000 1350000
+ 864000 1300000
+ 624000 1250000
+ >;
+ #cooling-cells = <2>;
+ cooling-min-level = <0>;
+ cooling-max-level = <3>;
+ };
+ };
+
+ thermal-zones {
+ cpu_thermal {
+ /* milliseconds */
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&rtp>;
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+
+ trips {
+ cpu_alert0: cpu_alert0 {
+ /* milliCelsius */
+ temperature = <850000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit: cpu_crit {
+ /* milliCelsius */
+ temperature = <100000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /*
+ * This is a dummy clock, to be used as placeholder on
+ * other mux clocks when a specific parent clock is not
+ * yet implemented. It should be dropped when the driver
+ * is complete.
+ */
+ dummy: dummy {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ };
+
+ osc24M: clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-osc-clk";
+ reg = <0x01c20050 0x4>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: clk@0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: clk@01c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ pll4: clk@01c20018 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll1-clk";
+ reg = <0x01c20018 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll4";
+ };
+
+ pll5: clk@01c20020 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-pll5-clk";
+ reg = <0x01c20020 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll5_ddr", "pll5_other";
+ };
+
+ pll6: clk@01c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6_sata", "pll6_other", "pll6";
+ };
+
+ /* dummy is 200M */
+ cpu: cpu@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
+ clock-output-names = "cpu";
+ };
+
+ axi: axi@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-axi-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ axi_gates: clk@01c2005c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-axi-gates-clk";
+ reg = <0x01c2005c 0x4>;
+ clocks = <&axi>;
+ clock-output-names = "axi_dram";
+ };
+
+ ahb: ahb@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-ahb-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&axi>;
+ clock-output-names = "ahb";
+ };
+
+ ahb_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-ahb-gates-clk";
+ reg = <0x01c20060 0x8>;
+ clocks = <&ahb>;
+ clock-output-names = "ahb_usb0", "ahb_ehci0",
+ "ahb_ohci0", "ahb_ehci1", "ahb_ohci1", "ahb_ss",
+ "ahb_dma", "ahb_bist", "ahb_mmc0", "ahb_mmc1",
+ "ahb_mmc2", "ahb_mmc3", "ahb_ms", "ahb_nand",
+ "ahb_sdram", "ahb_ace", "ahb_emac", "ahb_ts",
+ "ahb_spi0", "ahb_spi1", "ahb_spi2", "ahb_spi3",
+ "ahb_pata", "ahb_sata", "ahb_gps", "ahb_ve",
+ "ahb_tvd", "ahb_tve0", "ahb_tve1", "ahb_lcd0",
+ "ahb_lcd1", "ahb_csi0", "ahb_csi1", "ahb_hdmi",
+ "ahb_de_be0", "ahb_de_be1", "ahb_de_fe0",
+ "ahb_de_fe1", "ahb_mp", "ahb_mali400";
+ };
+
+ apb0: apb0@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb>;
+ clock-output-names = "apb0";
+ };
+
+ apb0_gates: clk@01c20068 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-apb0-gates-clk";
+ reg = <0x01c20068 0x4>;
+ clocks = <&apb0>;
+ clock-output-names = "apb0_codec", "apb0_spdif",
+ "apb0_ac97", "apb0_iis", "apb0_pio", "apb0_ir0",
+ "apb0_ir1", "apb0_keypad";
+ };
+
+ apb1: clk@01c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
+ clock-output-names = "apb1";
+ };
+
+ apb1_gates: clk@01c2006c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-apb1-gates-clk";
+ reg = <0x01c2006c 0x4>;
+ clocks = <&apb1>;
+ clock-output-names = "apb1_i2c0", "apb1_i2c1",
+ "apb1_i2c2", "apb1_can", "apb1_scr",
+ "apb1_ps20", "apb1_ps21", "apb1_uart0",
+ "apb1_uart1", "apb1_uart2", "apb1_uart3",
+ "apb1_uart4", "apb1_uart5", "apb1_uart6",
+ "apb1_uart7";
+ };
+
+ nand_clk: clk@01c20080 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20080 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "nand";
+ };
+
+ ms_clk: clk@01c20084 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20084 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ms";
+ };
+
+ mmc0_clk: clk@01c20088 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk@01c2008c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk@01c20090 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
+ };
+
+ mmc3_clk: clk@01c20094 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20094 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc3",
+ "mmc3_output",
+ "mmc3_sample";
+ };
+
+ ts_clk: clk@01c20098 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20098 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ts";
+ };
+
+ ss_clk: clk@01c2009c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c2009c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ss";
+ };
+
+ spi0_clk: clk@01c200a0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a0 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi0";
+ };
+
+ spi1_clk: clk@01c200a4 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a4 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi1";
+ };
+
+ spi2_clk: clk@01c200a8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a8 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi2";
+ };
+
+ pata_clk: clk@01c200ac {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200ac 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "pata";
+ };
+
+ ir0_clk: clk@01c200b0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200b0 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ir0";
+ };
+
+ ir1_clk: clk@01c200b4 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200b4 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ir1";
+ };
+
+ usb_clk: clk@01c200cc {
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-usb-clk";
+ reg = <0x01c200cc 0x4>;
+ clocks = <&pll6 1>;
+ clock-output-names = "usb_ohci0", "usb_ohci1", "usb_phy";
+ };
+
+ spi3_clk: clk@01c200d4 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200d4 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi3";
+ };
+ };
+
+ /*
+ * Note we use the address where the mmio registers start, not where
+ * the SRAM blocks start, this cannot be changed because that would be
+ * a devicetree ABI change.
+ */
+ soc@01c00000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram@00000000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00000000 0x4000>;
+ allwinner,sram-name = "A1";
+ };
+
+ sram@00004000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00004000 0x4000>;
+ allwinner,sram-name = "A2";
+ };
+
+ sram@00008000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00008000 0x4000>;
+ allwinner,sram-name = "A3-A4";
+ };
+
+ sram@00010000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00010000 0x1000>;
+ allwinner,sram-name = "D";
+ };
+
+ sram-controller@01c00000 {
+ compatible = "allwinner,sun4i-a10-sram-controller";
+ reg = <0x01c00000 0x30>;
+ };
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun4i-a10-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <27>;
+ clocks = <&ahb_gates 6>;
+ #dma-cells = <2>;
+ };
+
+ spi0: spi@01c05000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c05000 0x1000>;
+ interrupts = <10>;
+ clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 27>,
+ <&dma SUN4I_DMA_DEDICATED 26>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@01c06000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c06000 0x1000>;
+ interrupts = <11>;
+ clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 9>,
+ <&dma SUN4I_DMA_DEDICATED 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ emac: ethernet@01c0b000 {
+ compatible = "allwinner,sun4i-a10-emac";
+ reg = <0x01c0b000 0x1000>;
+ interrupts = <55>;
+ clocks = <&ahb_gates 17>;
+ status = "disabled";
+ };
+
+ mdio: mdio@01c0b080 {
+ compatible = "allwinner,sun4i-a10-mdio";
+ reg = <0x01c0b080 0x14>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ compatible = "allwinner,sun4i-a10-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ahb_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <32>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ compatible = "allwinner,sun4i-a10-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ahb_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <33>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ compatible = "allwinner,sun4i-a10-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ahb_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <34>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc3: mmc@01c12000 {
+ compatible = "allwinner,sun4i-a10-mmc";
+ reg = <0x01c12000 0x1000>;
+ clocks = <&ahb_gates 11>,
+ <&mmc3_clk 0>,
+ <&mmc3_clk 1>,
+ <&mmc3_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <35>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy@01c13400 {
+ #phy-cells = <1>;
+ compatible = "allwinner,sun4i-a10-usb-phy";
+ reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>;
+ reg-names = "phy_ctrl", "pmu1", "pmu2";
+ clocks = <&usb_clk 8>;
+ clock-names = "usb_phy";
+ resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>;
+ reset-names = "usb0_reset", "usb1_reset", "usb2_reset";
+ status = "disabled";
+ };
+
+ ehci0: usb@01c14000 {
+ compatible = "allwinner,sun4i-a10-ehci", "generic-ehci";
+ reg = <0x01c14000 0x100>;
+ interrupts = <39>;
+ clocks = <&ahb_gates 1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@01c14400 {
+ compatible = "allwinner,sun4i-a10-ohci", "generic-ohci";
+ reg = <0x01c14400 0x100>;
+ interrupts = <64>;
+ clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ spi2: spi@01c17000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c17000 0x1000>;
+ interrupts = <12>;
+ clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 29>,
+ <&dma SUN4I_DMA_DEDICATED 28>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ahci: sata@01c18000 {
+ compatible = "allwinner,sun4i-a10-ahci";
+ reg = <0x01c18000 0x1000>;
+ interrupts = <56>;
+ clocks = <&pll6 0>, <&ahb_gates 25>;
+ status = "disabled";
+ };
+
+ ehci1: usb@01c1c000 {
+ compatible = "allwinner,sun4i-a10-ehci", "generic-ehci";
+ reg = <0x01c1c000 0x100>;
+ interrupts = <40>;
+ clocks = <&ahb_gates 3>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@01c1c400 {
+ compatible = "allwinner,sun4i-a10-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <65>;
+ clocks = <&usb_clk 7>, <&ahb_gates 4>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ spi3: spi@01c1f000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c1f000 0x1000>;
+ interrupts = <50>;
+ clocks = <&ahb_gates 23>, <&spi3_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 31>,
+ <&dma SUN4I_DMA_DEDICATED 30>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ intc: interrupt-controller@01c20400 {
+ compatible = "allwinner,sun4i-a10-ic";
+ reg = <0x01c20400 0x400>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ pio: pinctrl@01c20800 {
+ compatible = "allwinner,sun4i-a10-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <28>;
+ clocks = <&apb0_gates 5>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #size-cells = <0>;
+ #gpio-cells = <3>;
+
+ pwm0_pins_a: pwm0@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "pwm";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ pwm1_pins_a: pwm1@0 {
+ allwinner,pins = "PI3";
+ allwinner,function = "pwm";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PB22", "PB23";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart0_pins_b: uart0@1 {
+ allwinner,pins = "PF2", "PF4";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart1_pins_a: uart1@0 {
+ allwinner,pins = "PA10", "PA11";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "i2c0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PB18", "PB19";
+ allwinner,function = "i2c1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PB20", "PB21";
+ allwinner,function = "i2c2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ emac_pins_a: emac0@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ allwinner,function = "emac";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ ir0_pins_a: ir0@0 {
+ allwinner,pins = "PB3","PB4";
+ allwinner,function = "ir0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ ir1_pins_a: ir1@0 {
+ allwinner,pins = "PB22","PB23";
+ allwinner,function = "ir1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ spi0_pins_a: spi0@0 {
+ allwinner,pins = "PI10", "PI11", "PI12", "PI13";
+ allwinner,function = "spi0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ spi1_pins_a: spi1@0 {
+ allwinner,pins = "PI16", "PI17", "PI18", "PI19";
+ allwinner,function = "spi1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ spi2_pins_a: spi2@0 {
+ allwinner,pins = "PB14", "PB15", "PB16", "PB17";
+ allwinner,function = "spi2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ spi2_pins_b: spi2@1 {
+ allwinner,pins = "PC19", "PC20", "PC21", "PC22";
+ allwinner,function = "spi2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ ps20_pins_a: ps20@0 {
+ allwinner,pins = "PI20", "PI21";
+ allwinner,function = "ps2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ ps21_pins_a: ps21@0 {
+ allwinner,pins = "PH12", "PH13";
+ allwinner,function = "ps2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0x90>;
+ interrupts = <22>;
+ clocks = <&osc24M>;
+ };
+
+ wdt: watchdog@01c20c90 {
+ compatible = "allwinner,sun4i-a10-wdt";
+ reg = <0x01c20c90 0x10>;
+ };
+
+ rtc: rtc@01c20d00 {
+ compatible = "allwinner,sun4i-a10-rtc";
+ reg = <0x01c20d00 0x20>;
+ interrupts = <24>;
+ };
+
+ pwm: pwm@01c20e00 {
+ compatible = "allwinner,sun4i-a10-pwm";
+ reg = <0x01c20e00 0xc>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ ir0: ir@01c21800 {
+ compatible = "allwinner,sun4i-a10-ir";
+ clocks = <&apb0_gates 6>, <&ir0_clk>;
+ clock-names = "apb", "ir";
+ interrupts = <5>;
+ reg = <0x01c21800 0x40>;
+ status = "disabled";
+ };
+
+ ir1: ir@01c21c00 {
+ compatible = "allwinner,sun4i-a10-ir";
+ clocks = <&apb0_gates 7>, <&ir1_clk>;
+ clock-names = "apb", "ir";
+ interrupts = <6>;
+ reg = <0x01c21c00 0x40>;
+ status = "disabled";
+ };
+
+ lradc: lradc@01c22800 {
+ compatible = "allwinner,sun4i-a10-lradc-keys";
+ reg = <0x01c22800 0x100>;
+ interrupts = <31>;
+ status = "disabled";
+ };
+
+ sid: eeprom@01c23800 {
+ compatible = "allwinner,sun4i-a10-sid";
+ reg = <0x01c23800 0x10>;
+ };
+
+ rtp: rtp@01c25000 {
+ compatible = "allwinner,sun4i-a10-ts";
+ reg = <0x01c25000 0x100>;
+ interrupts = <29>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ uart0: serial@01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <1>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 16>;
+ status = "disabled";
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <2>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 17>;
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <3>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 18>;
+ status = "disabled";
+ };
+
+ uart3: serial@01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 19>;
+ status = "disabled";
+ };
+
+ uart4: serial@01c29000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29000 0x400>;
+ interrupts = <17>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 20>;
+ status = "disabled";
+ };
+
+ uart5: serial@01c29400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29400 0x400>;
+ interrupts = <18>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 21>;
+ status = "disabled";
+ };
+
+ uart6: serial@01c29800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29800 0x400>;
+ interrupts = <19>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 22>;
+ status = "disabled";
+ };
+
+ uart7: serial@01c29c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29c00 0x400>;
+ interrupts = <20>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 23>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <7>;
+ clocks = <&apb1_gates 0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <8>;
+ clocks = <&apb1_gates 1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <9>;
+ clocks = <&apb1_gates 2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ps20: ps2@01c2a000 {
+ compatible = "allwinner,sun4i-a10-ps2";
+ reg = <0x01c2a000 0x400>;
+ interrupts = <62>;
+ clocks = <&apb1_gates 6>;
+ status = "disabled";
+ };
+
+ ps21: ps2@01c2a400 {
+ compatible = "allwinner,sun4i-a10-ps2";
+ reg = <0x01c2a400 0x400>;
+ interrupts = <63>;
+ clocks = <&apb1_gates 7>;
+ status = "disabled";
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a10s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Auxtek t004 A10s hdmi tv-stick";
+ compatible = "allwinner,auxtek-t004", "allwinner,sun5i-a10s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_t004>;
+
+ red {
+ label = "t004-tv-dongle:red:usr";
+ gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
+ default-state = "on";
+ };
+ };
+
+ reg_vmmc1: vmmc1 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_vcc_en_pin_t004>;
+ regulator-name = "vmmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 1 18 GPIO_ACTIVE_HIGH>; /* PB18 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vmmc1>;
+ bus-width = <4>;
+ non-removable;
+ cap-sdio-irq;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_t004: mmc0_cd_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc1_vcc_en_pin_t004: mmc1_vcc_en_pin@0 {
+ allwinner,pins = "PB18";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_t004: led_pins@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb1_vbus_pin_a {
+ allwinner,pins = "PG13";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a10s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "MK802-A10s";
+ compatible = "allwinner,a10s-mk802", "allwinner,sun5i-a10s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_mk802>;
+
+ red {
+ label = "mk802:red:usr";
+ gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mk802>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ led_pins_mk802: led_pins@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_mk802: mmc0_cd_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_mk802: usb1_vbus_pin@0 {
+ allwinner,pins = "PB10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_mk802>;
+ gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a10s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Olimex A10s-Olinuxino Micro";
+ compatible = "olimex,a10s-olinuxino-micro", "allwinner,sun5i-a10s";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxino>;
+
+ green {
+ label = "a10s-olinuxino-micro:green:usr";
+ gpios = <&pio 4 3 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_pins_a>;
+ phy = <&phy1>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ at24@50 {
+ compatible = "at,24c16";
+ pagesize = <16>;
+ reg = <0x50>;
+ read-only;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@191 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <191274>;
+ };
+
+ button@392 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <392644>;
+ };
+
+ button@601 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <601151>;
+ };
+
+ button@795 {
+ label = "Enter";
+ linux,code = <KEY_ENTER>;
+ channel = <0>;
+ voltage = <795090>;
+ };
+
+ button@987 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <987387>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino_micro>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>, <&mmc1_cd_pin_olinuxino_micro>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_olinuxino_micro: mmc0_cd_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc1_cd_pin_olinuxino_micro: mmc1_cd_pin@0 {
+ allwinner,pins = "PG13";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ led_pins_olinuxino: led_pins@0 {
+ allwinner,pins = "PE3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_olinuxino_m: usb1_vbus_pin@0 {
+ allwinner,pins = "PB10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_olinuxino_m>;
+ gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
--- /dev/null
+/*
+ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a10s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "R7 A10s hdmi tv-stick";
+ compatible = "allwinner,r7-tv-dongle", "allwinner,sun5i-a10s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_r7>;
+
+ green {
+ label = "r7-tv-dongle:green:usr";
+ gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_r7>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_r7: mmc0_cd_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ led_pins_r7: led_pins@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_r7: usb1_vbus_pin@0 {
+ allwinner,pins = "PG13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_r7>;
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include "sun5i.dtsi"
+
+#include <dt-bindings/dma/sun4i-a10.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ aliases {
+ ethernet0 = &emac;
+ };
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@0 {
+ compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0-hdmi";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>;
+ status = "disabled";
+ };
+
+ framebuffer@1 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
+ status = "disabled";
+ };
+ };
+
+ clocks {
+ ahb_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a10s-ahb-gates-clk";
+ reg = <0x01c20060 0x8>;
+ clocks = <&ahb>;
+ clock-output-names = "ahb_usbotg", "ahb_ehci", "ahb_ohci",
+ "ahb_ss", "ahb_dma", "ahb_bist", "ahb_mmc0",
+ "ahb_mmc1", "ahb_mmc2", "ahb_nand", "ahb_sdram",
+ "ahb_emac", "ahb_ts", "ahb_spi0", "ahb_spi1",
+ "ahb_spi2", "ahb_gps", "ahb_stimer", "ahb_ve",
+ "ahb_tve", "ahb_lcd", "ahb_csi", "ahb_hdmi",
+ "ahb_de_be", "ahb_de_fe", "ahb_iep", "ahb_mali400";
+ };
+
+ apb0_gates: clk@01c20068 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a10s-apb0-gates-clk";
+ reg = <0x01c20068 0x4>;
+ clocks = <&apb0>;
+ clock-output-names = "apb0_codec", "apb0_iis", "apb0_pio",
+ "apb0_ir", "apb0_keypad";
+ };
+
+ apb1_gates: clk@01c2006c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a10s-apb1-gates-clk";
+ reg = <0x01c2006c 0x4>;
+ clocks = <&apb1>;
+ clock-output-names = "apb1_i2c0", "apb1_i2c1",
+ "apb1_i2c2", "apb1_uart0", "apb1_uart1",
+ "apb1_uart2", "apb1_uart3";
+ };
+ };
+
+ soc@01c00000 {
+ emac: ethernet@01c0b000 {
+ compatible = "allwinner,sun4i-a10-emac";
+ reg = <0x01c0b000 0x1000>;
+ interrupts = <55>;
+ clocks = <&ahb_gates 17>;
+ status = "disabled";
+ };
+
+ mdio: mdio@01c0b080 {
+ compatible = "allwinner,sun4i-a10-mdio";
+ reg = <0x01c0b080 0x14>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ uart0: serial@01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <1>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 16>;
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <3>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 18>;
+ status = "disabled";
+ };
+ };
+};
+
+&pio {
+ compatible = "allwinner,sun5i-a10s-pinctrl";
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PB19", "PB20";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart2_pins_a: uart2@0 {
+ allwinner,pins = "PC18", "PC19";
+ allwinner,function = "uart2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart3_pins_a: uart3@0 {
+ allwinner,pins = "PG9", "PG10";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ emac_pins_a: emac0@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ allwinner,function = "emac";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc1_pins_a: mmc1@0 {
+ allwinner,pins = "PG3","PG4","PG5","PG6","PG7","PG8";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Ampe A76 for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+
+/ {
+ model = "Ampe A76";
+ compatible = "ampe,a76", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Forfun Q88db for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+
+/ {
+ model = "Forfun Q88db";
+ compatible = "forfun,q88db", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "HSG H702";
+ compatible = "hsg,h702", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_h702: mmc0_cd_pin@0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_ldo3>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the iNet 86VS for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+
+/ {
+ model = "iNet 86VS";
+ compatible = "inet,86vs", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2012 Maxime Ripard <maxime.ripard@free-electrons.com>
+ * Copyright 2013 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Olimex A13-Olinuxino Micro";
+ compatible = "olimex,a13-olinuxino-micro", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxinom>;
+
+ power {
+ label = "a13-olinuxino-micro:green:power";
+ gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxinom>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ led_pins_olinuxinom: led_pins@0 {
+ allwinner,pins = "PG9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 {
+ allwinner,pins = "PG11";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_olinuxinom>;
+ gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2012 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Olimex A13-Olinuxino";
+ compatible = "olimex,a13-olinuxino", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxino>;
+
+ power {
+ gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupts = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@191 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <191274>;
+ };
+
+ button@392 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <392644>;
+ };
+
+ button@601 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <601151>;
+ };
+
+ button@795 {
+ label = "Enter";
+ linux,code = <KEY_ENTER>;
+ channel = <0>;
+ voltage = <795090>;
+ };
+
+ button@987 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <987387>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ led_pins_olinuxino: led_pins@0 {
+ allwinner,pins = "PG9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_olinuxino: usb1_vbus_pin@0 {
+ allwinner,pins = "PG11";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_olinuxino>;
+ gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the TZX Q8 713b7 for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+
+/ {
+ model = "TZX Q8 713b7";
+ compatible = "tzx,q8-713b7", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Utoo P66";
+ compatible = "utoo,p66", "allwinner,sun5i-a13";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ i2c_lcd: i2c@0 {
+ /* The lcd panel i2c interface is hooked up via gpios */
+ compatible = "i2c-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_lcd_pins>;
+ gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>, /* PG12, sda */
+ <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10, scl */
+ i2c-gpio,delay-us = <5>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&lradc {
+ vref-supply = <®_ldo2>;
+ status = "okay";
+
+ button@200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_p66>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+
+ mmccard: mmccard@0 {
+ reg = <0>;
+ compatible = "mmc-card";
+ broken-hpi;
+ };
+};
+
+&pio {
+ mmc0_cd_pin_p66: mmc0_cd_pin@0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ i2c_lcd_pins: i2c_lcd_pin@0 {
+ allwinner,pins = "PG10", "PG12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_pin_a: usb0_vbus_pin@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_usb0_vbus {
+ gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
+
+&usbphy {
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_ldo3>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2012 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include "sun5i.dtsi"
+
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@0 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
+ status = "disabled";
+ };
+ };
+
+ thermal-zones {
+ cpu_thermal {
+ /* milliseconds */
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&rtp>;
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+
+ trips {
+ cpu_alert0: cpu_alert0 {
+ /* milliCelsius */
+ temperature = <850000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit: cpu_crit {
+ /* milliCelsius */
+ temperature = <100000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
+ clocks {
+ ahb_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a13-ahb-gates-clk";
+ reg = <0x01c20060 0x8>;
+ clocks = <&ahb>;
+ clock-output-names = "ahb_usbotg", "ahb_ehci", "ahb_ohci",
+ "ahb_ss", "ahb_dma", "ahb_bist", "ahb_mmc0",
+ "ahb_mmc1", "ahb_mmc2", "ahb_nand", "ahb_sdram",
+ "ahb_spi0", "ahb_spi1", "ahb_spi2", "ahb_stimer",
+ "ahb_ve", "ahb_lcd", "ahb_csi", "ahb_de_be",
+ "ahb_de_fe", "ahb_iep", "ahb_mali400";
+ };
+
+ apb0_gates: clk@01c20068 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a13-apb0-gates-clk";
+ reg = <0x01c20068 0x4>;
+ clocks = <&apb0>;
+ clock-output-names = "apb0_codec", "apb0_pio", "apb0_ir";
+ };
+
+ apb1_gates: clk@01c2006c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a13-apb1-gates-clk";
+ reg = <0x01c2006c 0x4>;
+ clocks = <&apb1>;
+ clock-output-names = "apb1_i2c0", "apb1_i2c1",
+ "apb1_i2c2", "apb1_uart1", "apb1_uart3";
+ };
+ };
+};
+
+&cpu0 {
+ clock-latency = <244144>; /* 8 32k periods */
+ operating-points = <
+ /* kHz uV */
+ 1008000 1400000
+ 912000 1350000
+ 864000 1300000
+ 624000 1200000
+ 576000 1200000
+ 432000 1200000
+ >;
+ #cooling-cells = <2>;
+ cooling-min-level = <0>;
+ cooling-max-level = <5>;
+};
+
+&pio {
+ compatible = "allwinner,sun5i-a13-pinctrl";
+
+ uart1_pins_a: uart1@0 {
+ allwinner,pins = "PE10", "PE11";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart1_pins_b: uart1@1 {
+ allwinner,pins = "PG3", "PG4";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
--- /dev/null
+/*
+ * Copyright 2012-2015 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/dma/sun4i-a10.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a8";
+ reg = <0x0>;
+ clocks = <&cpu>;
+ };
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /*
+ * This is a dummy clock, to be used as placeholder on
+ * other mux clocks when a specific parent clock is not
+ * yet implemented. It should be dropped when the driver
+ * is complete.
+ */
+ dummy: dummy {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ };
+
+ osc24M: clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-osc-clk";
+ reg = <0x01c20050 0x4>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: clk@0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: clk@01c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ pll4: clk@01c20018 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll1-clk";
+ reg = <0x01c20018 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll4";
+ };
+
+ pll5: clk@01c20020 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-pll5-clk";
+ reg = <0x01c20020 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll5_ddr", "pll5_other";
+ };
+
+ pll6: clk@01c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6_sata", "pll6_other", "pll6";
+ };
+
+ /* dummy is 200M */
+ cpu: cpu@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
+ clock-output-names = "cpu";
+ };
+
+ axi: axi@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-axi-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ ahb: ahb@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-ahb-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&axi>;
+ clock-output-names = "ahb";
+ };
+
+ apb0: apb0@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb>;
+ clock-output-names = "apb0";
+ };
+
+ apb1: clk@01c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
+ clock-output-names = "apb1";
+ };
+
+ axi_gates: clk@01c2005c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-axi-gates-clk";
+ reg = <0x01c2005c 0x4>;
+ clocks = <&axi>;
+ clock-output-names = "axi_dram";
+ };
+
+ nand_clk: clk@01c20080 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20080 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "nand";
+ };
+
+ ms_clk: clk@01c20084 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20084 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ms";
+ };
+
+ mmc0_clk: clk@01c20088 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk@01c2008c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk@01c20090 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
+ };
+
+ ts_clk: clk@01c20098 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c20098 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ts";
+ };
+
+ ss_clk: clk@01c2009c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c2009c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ss";
+ };
+
+ spi0_clk: clk@01c200a0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a0 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi0";
+ };
+
+ spi1_clk: clk@01c200a4 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a4 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi1";
+ };
+
+ spi2_clk: clk@01c200a8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a8 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "spi2";
+ };
+
+ ir0_clk: clk@01c200b0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200b0 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "ir0";
+ };
+
+ usb_clk: clk@01c200cc {
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun5i-a13-usb-clk";
+ reg = <0x01c200cc 0x4>;
+ clocks = <&pll6 1>;
+ clock-output-names = "usb_ohci0", "usb_phy";
+ };
+
+ mbus_clk: clk@01c2015c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun5i-a13-mbus-clk";
+ reg = <0x01c2015c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
+ clock-output-names = "mbus";
+ };
+ };
+
+ /*
+ * Note we use the address where the mmio registers start, not where
+ * the SRAM blocks start, this cannot be changed because that would be
+ * a devicetree ABI change.
+ */
+ soc@01c00000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram@00000000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00000000 0x4000>;
+ allwinner,sram-name = "A1";
+ };
+
+ sram@00004000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00004000 0x4000>;
+ allwinner,sram-name = "A2";
+ };
+
+ sram@00008000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00008000 0x4000>;
+ allwinner,sram-name = "A3-A4";
+ };
+
+ sram@00010000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00010000 0x1000>;
+ allwinner,sram-name = "D";
+ };
+
+ sram-controller@01c00000 {
+ compatible = "allwinner,sun4i-a10-sram-controller";
+ reg = <0x01c00000 0x30>;
+ };
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun4i-a10-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <27>;
+ clocks = <&ahb_gates 6>;
+ #dma-cells = <2>;
+ };
+
+ spi0: spi@01c05000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c05000 0x1000>;
+ interrupts = <10>;
+ clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 27>,
+ <&dma SUN4I_DMA_DEDICATED 26>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@01c06000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c06000 0x1000>;
+ interrupts = <11>;
+ clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 9>,
+ <&dma SUN4I_DMA_DEDICATED 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ahb_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <32>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ahb_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <33>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ahb_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <34>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy@01c13400 {
+ #phy-cells = <1>;
+ compatible = "allwinner,sun5i-a13-usb-phy";
+ reg = <0x01c13400 0x10 0x01c14800 0x4>;
+ reg-names = "phy_ctrl", "pmu1";
+ clocks = <&usb_clk 8>;
+ clock-names = "usb_phy";
+ resets = <&usb_clk 0>, <&usb_clk 1>;
+ reset-names = "usb0_reset", "usb1_reset";
+ status = "disabled";
+ };
+
+ ehci0: usb@01c14000 {
+ compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
+ reg = <0x01c14000 0x100>;
+ interrupts = <39>;
+ clocks = <&ahb_gates 1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@01c14400 {
+ compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
+ reg = <0x01c14400 0x100>;
+ interrupts = <40>;
+ clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ spi2: spi@01c17000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c17000 0x1000>;
+ interrupts = <12>;
+ clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 29>,
+ <&dma SUN4I_DMA_DEDICATED 28>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ intc: interrupt-controller@01c20400 {
+ compatible = "allwinner,sun4i-a10-ic";
+ reg = <0x01c20400 0x400>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ pio: pinctrl@01c20800 {
+ reg = <0x01c20800 0x400>;
+ interrupts = <28>;
+ clocks = <&apb0_gates 5>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #size-cells = <0>;
+ #gpio-cells = <3>;
+
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "i2c0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PB15", "PB16";
+ allwinner,function = "i2c1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PB17", "PB18";
+ allwinner,function = "i2c2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc2_pins_a: mmc2@0 {
+ allwinner,pins = "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11", "PC12", "PC13",
+ "PC14", "PC15";
+ allwinner,function = "mmc2";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0x90>;
+ interrupts = <22>;
+ clocks = <&osc24M>;
+ };
+
+ wdt: watchdog@01c20c90 {
+ compatible = "allwinner,sun4i-a10-wdt";
+ reg = <0x01c20c90 0x10>;
+ };
+
+ lradc: lradc@01c22800 {
+ compatible = "allwinner,sun4i-a10-lradc-keys";
+ reg = <0x01c22800 0x100>;
+ interrupts = <31>;
+ status = "disabled";
+ };
+
+ sid: eeprom@01c23800 {
+ compatible = "allwinner,sun4i-a10-sid";
+ reg = <0x01c23800 0x10>;
+ };
+
+ rtp: rtp@01c25000 {
+ compatible = "allwinner,sun5i-a13-ts";
+ reg = <0x01c25000 0x100>;
+ interrupts = <29>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <2>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 17>;
+ status = "disabled";
+ };
+
+ uart3: serial@01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <4>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 19>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <7>;
+ clocks = <&apb1_gates 0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <8>;
+ clocks = <&apb1_gates 1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun4i-a10-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <9>;
+ clocks = <&apb1_gates 2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ timer@01c60000 {
+ compatible = "allwinner,sun5i-a13-hstimer";
+ reg = <0x01c60000 0x1000>;
+ interrupts = <82>, <83>;
+ clocks = <&ahb_gates 28>;
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2014 Boris Brezillon
+ *
+ * Boris Brezillon <boris.brezillon@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Allwinner A31 APP4 EVB1 Evaluation Board";
+ compatible = "allwinner,app4-evb1", "allwinner,sun6i-a31";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&pio {
+ usb1_vbus_pin_a: usb1_vbus_pin@0 {
+ allwinner,pins = "PH27";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_a>;
+ gpio = <&pio 7 27 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "WITS A31 Colombus Evaluation Board";
+ compatible = "wits,colombus", "allwinner,sun6i-a31";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "fail";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_colombus>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc0_pins_a {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&pio {
+ mmc0_cd_pin_colombus: mmc0_cd_pin@0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb2_vbus_pin_colombus: usb2_vbus_pin@0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb2_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb2_vbus_pin_colombus>;
+ gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Merrii A31 Hummingbird";
+ compatible = "merrii,a31-hummingbird", "allwinner,sun6i-a31";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 30000>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ /* pull-ups and devices require AXP221 DLDO3 */
+ status = "failed";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_hummingbird>;
+ vmmc-supply = <&vcc_3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc0_pins_a {
+ /* external pull-ups missing for some pins */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_hummingbird>;
+ vmmc-supply = <&vcc_wifi>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_hummingbird: mmc0_cd_pin@0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ wifi_reset_pin_hummingbird: wifi_reset_pin@0 {
+ allwinner,pins = "PG10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&p2wi {
+ status = "okay";
+
+ axp221: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ dcdc1-supply = <&vcc_3v0>;
+ dcdc5-supply = <&vcc_dram>;
+
+ regulators {
+ x-powers,dcdc-freq = <3000>;
+
+ vcc_3v0: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+ };
+
+ vdd_cpu: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ vdd_gpu: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ vdd_sys_dll: dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys-dll";
+ };
+
+ vcc_dram: dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+ };
+
+ vcc_wifi: aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_wifi";
+ };
+
+ avcc: aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+ };
+ };
+};
+
+®_usb1_vbus {
+ gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb1_vbus_pin_a {
+ /* different pin from sunxi-common-regulators */
+ allwinner,pins = "PH24";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Marcus Cooper <codekipper@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Mele I7 Quad top set box";
+ compatible = "mele,i7", "allwinner,sun6i-a31";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_i7>;
+
+ blue {
+ label = "i7:blue:usr";
+ gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_i7>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ led_pins_i7: led_pins@0 {
+ allwinner,pins = "PH13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_i7: mmc0_cd_pin@0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_i7: usb1_vbus_pin@0 {
+ allwinner,pins = "PC27";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_i7>;
+ gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Mele M9 / A1000G Quad top set box";
+ compatible = "mele,m9", "allwinner,sun6i-a31";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_m9>;
+
+ blue {
+ label = "m9:blue:usr";
+ gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ led_pins_m9: led_pins@0 {
+ allwinner,pins = "PH13";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_m9: mmc0_cd_pin@0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_m9: usb1_vbus_pin@0 {
+ allwinner,pins = "PC27";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_m9>;
+ gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Mixtile LOFT-Q for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun6i-a31.dtsi"
+
+/ {
+ model = "Mixtile LOFT-Q";
+ compatible = "mixtile,loft-q", "allwinner,sun6i-a31";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ aliases {
+ ethernet0 = &gmac;
+ };
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@0 {
+ compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0-hdmi";
+ clocks = <&pll6 0>;
+ status = "disabled";
+ };
+
+ framebuffer@1 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0";
+ clocks = <&pll6 0>;
+ status = "disabled";
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <24000000>;
+ arm,cpu-registers-not-fw-configured;
+ };
+
+ cpus {
+ enable-method = "allwinner,sun6i-a31";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&cpu>;
+ clock-latency = <244144>; /* 8 32k periods */
+ operating-points = <
+ /* kHz uV */
+ 1008000 1200000
+ 864000 1200000
+ 720000 1100000
+ 480000 1000000
+ >;
+ #cooling-cells = <2>;
+ cooling-min-level = <0>;
+ cooling-max-level = <3>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ thermal-zones {
+ cpu_thermal {
+ /* milliseconds */
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&rtp>;
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+
+ trips {
+ cpu_alert0: cpu_alert0 {
+ /* milliCelsius */
+ temperature = <70000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit: cpu_crit {
+ /* milliCelsius */
+ temperature = <100000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu";
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
+ osc32k: clk@0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: clk@01c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun6i-a31-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ pll6: clk@01c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6", "pll6x2";
+ };
+
+ cpu: cpu@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20050 0x4>;
+
+ /*
+ * PLL1 is listed twice here.
+ * While it looks suspicious, it's actually documented
+ * that way both in the datasheet and in the code from
+ * Allwinner.
+ */
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+ clock-output-names = "cpu";
+ };
+
+ axi: axi@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-axi-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ ahb1: ahb1@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun6i-a31-ahb1-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+ clock-output-names = "ahb1";
+ };
+
+ ahb1_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-ahb1-gates-clk";
+ reg = <0x01c20060 0x8>;
+ clocks = <&ahb1>;
+ clock-output-names = "ahb1_mipidsi", "ahb1_ss",
+ "ahb1_dma", "ahb1_mmc0", "ahb1_mmc1",
+ "ahb1_mmc2", "ahb1_mmc3", "ahb1_nand1",
+ "ahb1_nand0", "ahb1_sdram",
+ "ahb1_gmac", "ahb1_ts", "ahb1_hstimer",
+ "ahb1_spi0", "ahb1_spi1", "ahb1_spi2",
+ "ahb1_spi3", "ahb1_otg", "ahb1_ehci0",
+ "ahb1_ehci1", "ahb1_ohci0",
+ "ahb1_ohci1", "ahb1_ohci2", "ahb1_ve",
+ "ahb1_lcd0", "ahb1_lcd1", "ahb1_csi",
+ "ahb1_hdmi", "ahb1_de0", "ahb1_de1",
+ "ahb1_fe0", "ahb1_fe1", "ahb1_mp",
+ "ahb1_gpu", "ahb1_deu0", "ahb1_deu1",
+ "ahb1_drc0", "ahb1_drc1";
+ };
+
+ apb1: apb1@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb1>;
+ clock-output-names = "apb1";
+ };
+
+ apb1_gates: clk@01c20068 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-apb1-gates-clk";
+ reg = <0x01c20068 0x4>;
+ clocks = <&apb1>;
+ clock-output-names = "apb1_codec", "apb1_digital_mic",
+ "apb1_pio", "apb1_daudio0",
+ "apb1_daudio1";
+ };
+
+ apb2: clk@01c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+ clock-output-names = "apb2";
+ };
+
+ apb2_gates: clk@01c2006c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-apb2-gates-clk";
+ reg = <0x01c2006c 0x4>;
+ clocks = <&apb2>;
+ clock-output-names = "apb2_i2c0", "apb2_i2c1",
+ "apb2_i2c2", "apb2_i2c3", "apb2_uart0",
+ "apb2_uart1", "apb2_uart2", "apb2_uart3",
+ "apb2_uart4", "apb2_uart5";
+ };
+
+ mmc0_clk: clk@01c20088 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk@01c2008c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk@01c20090 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
+ };
+
+ mmc3_clk: clk@01c20094 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20094 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "mmc3",
+ "mmc3_output",
+ "mmc3_sample";
+ };
+
+ spi0_clk: clk@01c200a0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a0 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "spi0";
+ };
+
+ spi1_clk: clk@01c200a4 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a4 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "spi1";
+ };
+
+ spi2_clk: clk@01c200a8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200a8 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "spi2";
+ };
+
+ spi3_clk: clk@01c200ac {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01c200ac 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "spi3";
+ };
+
+ usb_clk: clk@01c200cc {
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-usb-clk";
+ reg = <0x01c200cc 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "usb_phy0", "usb_phy1", "usb_phy2",
+ "usb_ohci0", "usb_ohci1",
+ "usb_ohci2";
+ };
+
+ /*
+ * The following two are dummy clocks, placeholders used in the gmac_tx
+ * clock. The gmac driver will choose one parent depending on the PHY
+ * interface mode, using clk_set_rate auto-reparenting.
+ * The actual TX clock rate is not controlled by the gmac_tx clock.
+ */
+ mii_phy_tx_clk: clk@1 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ clock-output-names = "mii_phy_tx";
+ };
+
+ gmac_int_tx_clk: clk@2 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac_int_tx";
+ };
+
+ gmac_tx_clk: clk@01c200d0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun7i-a20-gmac-clk";
+ reg = <0x01c200d0 0x4>;
+ clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>;
+ clock-output-names = "gmac_tx";
+ };
+ };
+
+ soc@01c00000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun6i-a31-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 6>;
+ resets = <&ahb1_rst 6>;
+ #dma-cells = <1>;
+
+ /* DMA controller requires AHB1 clocked from PLL6 */
+ assigned-clocks = <&ahb1>;
+ assigned-clock-parents = <&pll6 0>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ahb1_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb1_rst 8>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ahb1_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb1_rst 9>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ahb1_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb1_rst 10>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc3: mmc@01c12000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c12000 0x1000>;
+ clocks = <&ahb1_gates 11>,
+ <&mmc3_clk 0>,
+ <&mmc3_clk 1>,
+ <&mmc3_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb1_rst 11>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy@01c19400 {
+ compatible = "allwinner,sun6i-a31-usb-phy";
+ reg = <0x01c19400 0x10>,
+ <0x01c1a800 0x4>,
+ <0x01c1b800 0x4>;
+ reg-names = "phy_ctrl",
+ "pmu1",
+ "pmu2";
+ clocks = <&usb_clk 8>,
+ <&usb_clk 9>,
+ <&usb_clk 10>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy";
+ resets = <&usb_clk 0>,
+ <&usb_clk 1>,
+ <&usb_clk 2>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb@01c1a000 {
+ compatible = "allwinner,sun6i-a31-ehci", "generic-ehci";
+ reg = <0x01c1a000 0x100>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 26>;
+ resets = <&ahb1_rst 26>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@01c1a400 {
+ compatible = "allwinner,sun6i-a31-ohci", "generic-ohci";
+ reg = <0x01c1a400 0x100>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 29>, <&usb_clk 16>;
+ resets = <&ahb1_rst 29>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci1: usb@01c1b000 {
+ compatible = "allwinner,sun6i-a31-ehci", "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 27>;
+ resets = <&ahb1_rst 27>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@01c1b400 {
+ compatible = "allwinner,sun6i-a31-ohci", "generic-ohci";
+ reg = <0x01c1b400 0x100>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 30>, <&usb_clk 17>;
+ resets = <&ahb1_rst 30>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb@01c1c400 {
+ compatible = "allwinner,sun6i-a31-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 31>, <&usb_clk 18>;
+ resets = <&ahb1_rst 31>;
+ status = "disabled";
+ };
+
+ pio: pinctrl@01c20800 {
+ compatible = "allwinner,sun6i-a31-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 5>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #size-cells = <0>;
+ #gpio-cells = <3>;
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PH20", "PH21";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PH14", "PH15";
+ allwinner,function = "i2c0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PH16", "PH17";
+ allwinner,function = "i2c1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PH18", "PH19";
+ allwinner,function = "i2c2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc1_pins_a: mmc1@0 {
+ allwinner,pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ gmac_pins_mii_a: gmac_mii@0 {
+ allwinner,pins = "PA0", "PA1", "PA2", "PA3",
+ "PA8", "PA9", "PA11",
+ "PA12", "PA13", "PA14", "PA19",
+ "PA20", "PA21", "PA22", "PA23",
+ "PA24", "PA26", "PA27";
+ allwinner,function = "gmac";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ gmac_pins_gmii_a: gmac_gmii@0 {
+ allwinner,pins = "PA0", "PA1", "PA2", "PA3",
+ "PA4", "PA5", "PA6", "PA7",
+ "PA8", "PA9", "PA10", "PA11",
+ "PA12", "PA13", "PA14", "PA15",
+ "PA16", "PA17", "PA18", "PA19",
+ "PA20", "PA21", "PA22", "PA23",
+ "PA24", "PA25", "PA26", "PA27";
+ allwinner,function = "gmac";
+ /*
+ * data lines in GMII mode run at 125MHz and
+ * might need a higher signal drive strength
+ */
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ gmac_pins_rgmii_a: gmac_rgmii@0 {
+ allwinner,pins = "PA0", "PA1", "PA2", "PA3",
+ "PA9", "PA10", "PA11",
+ "PA12", "PA13", "PA14", "PA19",
+ "PA20", "PA25", "PA26", "PA27";
+ allwinner,function = "gmac";
+ /*
+ * data lines in RGMII mode use DDR mode
+ * and need a higher signal drive strength
+ */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ ahb1_rst: reset@01c202c0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-ahb1-reset";
+ reg = <0x01c202c0 0xc>;
+ };
+
+ apb1_rst: reset@01c202d0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d0 0x4>;
+ };
+
+ apb2_rst: reset@01c202d8 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d8 0x4>;
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ wdt1: watchdog@01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ };
+
+ rtp: rtp@01c25000 {
+ compatible = "allwinner,sun6i-a31-ts";
+ reg = <0x01c25000 0x100>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ uart0: serial@01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 16>;
+ resets = <&apb2_rst 16>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 17>;
+ resets = <&apb2_rst 17>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 18>;
+ resets = <&apb2_rst 18>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 19>;
+ resets = <&apb2_rst 19>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart4: serial@01c29000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 20>;
+ resets = <&apb2_rst 20>;
+ dmas = <&dma 10>, <&dma 10>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart5: serial@01c29400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29400 0x400>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 21>;
+ resets = <&apb2_rst 21>;
+ dmas = <&dma 22>, <&dma 22>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb2_gates 0>;
+ resets = <&apb2_rst 0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb2_gates 1>;
+ resets = <&apb2_rst 1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb2_gates 2>;
+ resets = <&apb2_rst 2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@01c2b800 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b800 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb2_gates 3>;
+ resets = <&apb2_rst 3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ gmac: ethernet@01c30000 {
+ compatible = "allwinner,sun7i-a20-gmac";
+ reg = <0x01c30000 0x1054>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&ahb1_gates 17>, <&gmac_tx_clk>;
+ clock-names = "stmmaceth", "allwinner_gmac_tx";
+ resets = <&ahb1_rst 17>;
+ reset-names = "stmmaceth";
+ snps,pbl = <2>;
+ snps,fixed-burst;
+ snps,force_sf_dma_mode;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ timer@01c60000 {
+ compatible = "allwinner,sun6i-a31-hstimer", "allwinner,sun7i-a20-hstimer";
+ reg = <0x01c60000 0x1000>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 19>;
+ resets = <&ahb1_rst 19>;
+ };
+
+ spi0: spi@01c68000 {
+ compatible = "allwinner,sun6i-a31-spi";
+ reg = <0x01c68000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 20>, <&spi0_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ resets = <&ahb1_rst 20>;
+ status = "disabled";
+ };
+
+ spi1: spi@01c69000 {
+ compatible = "allwinner,sun6i-a31-spi";
+ reg = <0x01c69000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 21>, <&spi1_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 24>, <&dma 24>;
+ dma-names = "rx", "tx";
+ resets = <&ahb1_rst 21>;
+ status = "disabled";
+ };
+
+ spi2: spi@01c6a000 {
+ compatible = "allwinner,sun6i-a31-spi";
+ reg = <0x01c6a000 0x1000>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 25>, <&dma 25>;
+ dma-names = "rx", "tx";
+ resets = <&ahb1_rst 22>;
+ status = "disabled";
+ };
+
+ spi3: spi@01c6b000 {
+ compatible = "allwinner,sun6i-a31-spi";
+ reg = <0x01c6b000 0x1000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 23>, <&spi3_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 26>, <&dma 26>;
+ dma-names = "rx", "tx";
+ resets = <&ahb1_rst 23>;
+ status = "disabled";
+ };
+
+ gic: interrupt-controller@01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ rtc: rtc@01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ nmi_intc: interrupt-controller@01f00c0c {
+ compatible = "allwinner,sun6i-a31-sc-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01f00c0c 0x38>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ prcm@01f01400 {
+ compatible = "allwinner,sun6i-a31-prcm";
+ reg = <0x01f01400 0x200>;
+
+ ar100: ar100_clk {
+ compatible = "allwinner,sun6i-a31-ar100-clk";
+ #clock-cells = <0>;
+ clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+ clock-output-names = "ar100";
+ };
+
+ ahb0: ahb0_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&ar100>;
+ clock-output-names = "ahb0";
+ };
+
+ apb0: apb0_clk {
+ compatible = "allwinner,sun6i-a31-apb0-clk";
+ #clock-cells = <0>;
+ clocks = <&ahb0>;
+ clock-output-names = "apb0";
+ };
+
+ apb0_gates: apb0_gates_clk {
+ compatible = "allwinner,sun6i-a31-apb0-gates-clk";
+ #clock-cells = <1>;
+ clocks = <&apb0>;
+ clock-output-names = "apb0_pio", "apb0_ir",
+ "apb0_timer", "apb0_p2wi",
+ "apb0_uart", "apb0_1wire",
+ "apb0_i2c";
+ };
+
+ ir_clk: ir_clk {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ clocks = <&osc32k>, <&osc24M>;
+ clock-output-names = "ir";
+ };
+
+ apb0_rst: apb0_rst {
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ #reset-cells = <1>;
+ };
+ };
+
+ cpucfg@01f01c00 {
+ compatible = "allwinner,sun6i-a31-cpuconfig";
+ reg = <0x01f01c00 0x300>;
+ };
+
+ ir: ir@01f02000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ clocks = <&apb0_gates 1>, <&ir_clk>;
+ clock-names = "apb", "ir";
+ resets = <&apb0_rst 1>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01f02000 0x40>;
+ status = "disabled";
+ };
+
+ r_pio: pinctrl@01f02c00 {
+ compatible = "allwinner,sun6i-a31-r-pinctrl";
+ reg = <0x01f02c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 0>;
+ resets = <&apb0_rst 0>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #size-cells = <0>;
+ #gpio-cells = <3>;
+
+ ir_pins_a: ir@0 {
+ allwinner,pins = "PL4";
+ allwinner,function = "s_ir";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ p2wi_pins: p2wi {
+ allwinner,pins = "PL0", "PL1";
+ allwinner,function = "s_p2wi";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ p2wi: i2c@01f03400 {
+ compatible = "allwinner,sun6i-a31-p2wi";
+ reg = <0x01f03400 0x400>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 3>;
+ clock-frequency = <100000>;
+ resets = <&apb0_rst 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&p2wi_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31s.dtsi"
+
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "CSQ CS908 top set box";
+ compatible = "csq,cs908", "allwinner,sun6i-a31s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the MSI Primo81 for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun6i-a31s.dtsi"
+
+/ {
+ model = "MSI Primo81";
+ compatible = "msi,primo81", "allwinner,sun6i-a31s";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * The A31s is the same die as the A31 in a different package, this is
+ * reflected by it having different pinctrl compatible everything else is
+ * identical.
+ */
+
+#include "sun6i-a31.dtsi"
+
+&pio {
+ compatible = "allwinner,sun6i-a31s-pinctrl";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Ainol AW1 for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+
+/ {
+ model = "Ainol AW1";
+ compatible = "ainol,aw1", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "LeMaker Banana Pi";
+ compatible = "lemaker,bananapi", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart3;
+ serial2 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bananapi>;
+
+ green {
+ label = "bananapi:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bananapi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_bananapi: mmc0_cd_pin@0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ gmac_power_pin_bananapi: gmac_power_pin@0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_bananapi: led_pins@0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_b>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "LeMaker Banana Pro";
+ compatible = "lemaker,bananapro", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart2;
+ serial2 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bananapro>;
+
+ blue {
+ label = "bananapro:blue:usr";
+ gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "bananapro:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bananapro>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_vmmc3: vmmc3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vmmc3_pin_bananapro>;
+ regulator-name = "vmmc3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapro>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_vmmc3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ gmac_power_pin_bananapro: gmac_power_pin@0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_bananapro: led_pins@0 {
+ allwinner,pins = "PH24", "PG2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_bananapro: mmc0_cd_pin@0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
+ allwinner,pins = "PH0";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ vmmc3_pin_bananapro: vmmc3_pin@0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_bananapro>;
+ gpio = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin_bananapro>;
+ gpio = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Cubietech Cubieboard2";
+ compatible = "cubietech,cubieboard2", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_cubieboard2>;
+
+ blue {
+ label = "cubieboard2:blue:usr";
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "cubieboard2:green:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ led_pins_cubieboard2: led_pins@0 {
+ allwinner,pins = "PH20", "PH21";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2013 Oliver Schinagl
+ *
+ * Oliver Schinagl <oliver@schinagl.nl>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Cubietech Cubietruck";
+ compatible = "cubietech,cubietruck", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_cubietruck>;
+
+ blue {
+ label = "cubietruck:blue:usr";
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ orange {
+ label = "cubietruck:orange:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ white {
+ label = "cubietruck:white:usr";
+ gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "cubietruck:green:usr";
+ gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_vmmc3: vmmc3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vmmc3_pin_cubietruck>;
+ regulator-name = "vmmc3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_vmmc3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc3_pins_a {
+ /* AP6210 requires pull-up */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ vmmc3_pin_cubietruck: vmmc3_pin@0 {
+ allwinner,pins = "PH9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 {
+ allwinner,pins = "PH12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_cubietruck: led_pins@0 {
+ allwinner,pins = "PH7", "PH11", "PH20", "PH21";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_pin_a: usb0_vbus_pin@0 {
+ allwinner,pins = "PH17";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>, <&pwm1_pins_a>;
+ status = "okay";
+};
+
+®_ahci_5v {
+ pinctrl-0 = <&ahci_pwr_pin_cubietruck>;
+ gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ pinctrl-0 = <&usb0_vbus_pin_a>;
+ gpio = <&pio 7 17 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2013 Wills Wang
+ *
+ * Wills Wang <wills.wang.open@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Merrii A20 Hummingbird";
+ compatible = "merrii,a20-hummingbird", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_mmc3_vdd: mmc3_vdd {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_vdd_pin_a20_hummingbird>;
+ regulator-name = "mmc3_vdd";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ enable-active-high;
+ gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ };
+
+ reg_gmac_vdd: gmac_vdd {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_vdd_pin_a20_hummingbird>;
+ regulator-name = "gmac_vdd";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ enable-active-high;
+ gpio = <&pio 7 16 GPIO_ACTIVE_HIGH>; /* PH16 */
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_vdd>;
+ /* phy reset config */
+ snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
+ snps,reset-active-low;
+ /* wait 1s after reset, otherwise fail to read phy id */
+ snps,reset-delays-us = <0 10000 1000000>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_mmc3_vdd>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ ahci_pwr_pin_a20_hummingbird: ahci_pwr_pin@0 {
+ allwinner,pins = "PH15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_a20_hummingbird: usb1_vbus_pin@0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc3_vdd_pin_a20_hummingbird: mmc3_vdd_pin@0 {
+ allwinner,pins = "PH9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ gmac_vdd_pin_a20_hummingbird: gmac_vdd_pin@0 {
+ allwinner,pins = "PH16";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins_a>;
+ status = "okay";
+};
+
+®_ahci_5v {
+ pinctrl-0 = <&ahci_pwr_pin_a20_hummingbird>;
+ gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
+ status = "okay";
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_a20_hummingbird>;
+ gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_b>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_a>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart5_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "I12 / Q5 / QT840A A20 tvbox";
+ compatible = "allwinner,i12-tvbox", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_i12_tvbox>;
+
+ red {
+ label = "i12_tvbox:red:usr";
+ gpios = <&pio 7 9 GPIO_ACTIVE_LOW>;
+ };
+
+ blue {
+ label = "i12_tvbox:blue:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_vmmc3: vmmc3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vmmc3_pin_i12_tvbox>;
+ regulator-name = "vmmc3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_vmmc3_io: vmmc3-io {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vmmc3_io_pin_i12_tvbox>;
+ regulator-name = "vmmc3-io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ /* This controls VCC-PI, must be always on! */
+ regulator-always-on;
+ enable-active-high;
+ gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_i12_tvbox>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <50000>;
+ enable-active-high;
+ gpio = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_vmmc3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc3_pins_a {
+ /* AP6210 / AP6330 requires pull-up */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ vmmc3_pin_i12_tvbox: vmmc3_pin@0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ vmmc3_io_pin_i12_tvbox: vmmc3_io_pin@0 {
+ allwinner,pins = "PH12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ gmac_power_pin_i12_tvbox: gmac_power_pin@0 {
+ allwinner,pins = "PH21";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_i12_tvbox: led_pins@0 {
+ allwinner,pins = "PH9", "PH20";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Mele M3";
+ compatible = "mele,m3", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_m3>;
+
+ blue {
+ label = "m3:blue:usr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ led_pins_m3: led_pins@0 {
+ allwinner,pins = "PH20";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Mele M5 for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+
+/ {
+ model = "Mele M5";
+ compatible = "mele,m5", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the MK808C for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+
+/ {
+ model = "MK808C";
+ compatible = "allwinner,mk808c", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * This is based on sun4i-a10-olinuxino-lime.dts
+ *
+ * Copyright 2014 - Hans de Goede <hdegoede@redhat.com>
+ * Copyright (c) 2014 FUKAUMI Naoki <naobsd@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Olimex A20-OLinuXino-LIME";
+ compatible = "olimex,a20-olinuxino-lime", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxinolime>;
+
+ green {
+ label = "a20-olinuxino-lime:green:usr";
+ gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 {
+ allwinner,pins = "PC3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_olinuxinolime: led_pins@0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
+ gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 - Iain Paton <ipaton0@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Olimex A20-OLinuXino-LIME2";
+ compatible = "olimex,a20-olinuxino-lime2", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxinolime>;
+
+ green {
+ label = "a20-olinuxino-lime2:green:usr";
+ gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ reg_axp_ipsout: axp_ipsout {
+ compatible = "regulator-fixed";
+ regulator-name = "axp-ipsout";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ acin-supply = <®_axp_ipsout>;
+ vin2-supply = <®_axp_ipsout>;
+ vin3-supply = <®_axp_ipsout>;
+ ldo24in-supply = <®_axp_ipsout>;
+ ldo3in-supply = <®_axp_ipsout>;
+
+ regulators {
+ vdd_rtc: ldo1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ };
+
+ avcc: ldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vcc_csi0: ldo3 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3500000>;
+ regulator-always-on;
+ };
+
+ vcc_csi1: ldo4 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vdd_cpu: dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <2275000>;
+ regulator-always-on;
+ };
+
+ vdd_int: dcdc3 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3500000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 {
+ allwinner,pins = "PC3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_olinuxinolime: led_pins@0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
+ gpio = <&pio 2 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Olimex A20-Olinuxino Micro";
+ compatible = "olimex,a20-olinuxino-micro", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart6;
+ serial2 = &uart7;
+ spi0 = &spi1;
+ spi1 = &spi2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxino>;
+
+ green {
+ label = "a20-olinuxino-micro:green:usr";
+ gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@191 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <191274>;
+ };
+
+ button@392 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <392644>;
+ };
+
+ button@601 {
+ label = "Menu";
+ linux,code = <KEY_MENU>;
+ channel = <0>;
+ voltage = <601151>;
+ };
+
+ button@795 {
+ label = "Search";
+ linux,code = <KEY_SEARCH>;
+ channel = <0>;
+ voltage = <795090>;
+ };
+
+ button@987 {
+ label = "Home";
+ linux,code = <KEY_HOMEPAGE>;
+ channel = <0>;
+ voltage = <987387>;
+ };
+
+ button@1184 {
+ label = "Esc";
+ linux,code = <KEY_ESC>;
+ channel = <0>;
+ voltage = <1184678>;
+ };
+
+ button@1398 {
+ label = "Enter";
+ linux,code = <KEY_ENTER>;
+ channel = <0>;
+ voltage = <1398804>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olinuxinom>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ mmc3_cd_pin_olinuxinom: mmc3_cd_pin@0 {
+ allwinner,pins = "PH11";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ led_pins_olinuxino: led_pins@0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins_a>;
+ status = "okay";
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart6_pins_a>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Orange Pi Mini";
+ compatible = "xunlong,orangepi-mini", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_orangepi>;
+
+ green {
+ label = "orangepi:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
+ };
+
+ blue {
+ label = "orangepi:blue:usr";
+ gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>; /* PH25 */
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_orangepi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_orangepi>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_orangepi>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_orangepi: mmc0_cd_pin@0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc3_cd_pin_orangepi: mmc3_cd_pin@0 {
+ allwinner,pins = "PH11";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ gmac_power_pin_orangepi: gmac_power_pin@0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_orangepi: led_pins@0 {
+ allwinner,pins = "PH24", "PH25";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
+ allwinner,pins = "PH26";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_bananapro>;
+ gpio = <&pio 7 26 GPIO_ACTIVE_HIGH>; /* PH26 */
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin_bananapro>;
+ gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Orange Pi";
+ compatible = "xunlong,orangepi", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_orangepi>;
+
+ green {
+ label = "orangepi:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_orangepi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_orangepi>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_orangepi: mmc0_cd_pin@0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ gmac_power_pin_orangepi: gmac_power_pin@0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_orangepi: led_pins@0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
+ allwinner,pins = "PH26";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_bananapro>;
+ gpio = <&pio 7 26 GPIO_ACTIVE_HIGH>; /* PH26 */
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin_bananapro>;
+ gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Adam Sampson <ats@offog.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "LinkSprite pcDuino3 Nano";
+ compatible = "linksprite,pcduino3-nano", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_pcduino3_nano>;
+
+ /* Marked "LED3" on the PCB. */
+ usr1 {
+ label = "pcduino3-nano:green:usr1";
+ gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; /* PH16 */
+ };
+
+ /* Marked "LED4" on the PCB. */
+ usr2 {
+ label = "pcduino3-nano:green:usr2";
+ gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; /* PH15 */
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin@0 {
+ allwinner,pins = "PH2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_pcduino3_nano: led_pins@0 {
+ allwinner,pins = "PH16", "PH15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin@0 {
+ allwinner,pins = "PH11";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ pinctrl-0 = <&ahci_pwr_pin_pcduino3_nano>;
+ gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
+ status = "okay";
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;
+ gpio = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
* Copyright 2014 Zoltan HERPAI
* Zoltan HERPAI <wigyori@uid0.hu>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
-/include/ "sun7i-a20.dtsi"
-/include/ "sunxi-common-regulators.dtsi"
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "LinkSprite pcDuino3";
compatible = "linksprite,pcduino3", "allwinner,sun7i-a20";
- chosen {
- stdout-path = &uart0;
+ aliases {
+ serial0 = &uart0;
};
- soc@01c00000 {
- mmc0: mmc@01c0f000 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 7 1 0>; /* PH1 */
- cd-inverted;
- status = "okay";
- };
-
- usbphy: phy@01c13400 {
- usb1_vbus-supply = <®_usb1_vbus>;
- usb2_vbus-supply = <®_usb2_vbus>;
- status = "okay";
- };
-
- ehci0: usb@01c14000 {
- status = "okay";
- };
-
- ohci0: usb@01c14400 {
- status = "okay";
- };
-
- ahci: sata@01c18000 {
- target-supply = <®_ahci_5v>;
- status = "okay";
- };
-
- ehci1: usb@01c1c000 {
- status = "okay";
- };
-
- ohci1: usb@01c1c400 {
- status = "okay";
- };
-
- pinctrl@01c20800 {
- ahci_pwr_pin_a: ahci_pwr_pin@0 {
- allwinner,pins = "PH2";
- };
-
- led_pins_pcduino3: led_pins@0 {
- allwinner,pins = "PH15", "PH16";
- allwinner,function = "gpio_out";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
-
- key_pins_pcduino3: key_pins@0 {
- allwinner,pins = "PH17", "PH18", "PH19";
- allwinner,function = "gpio_in";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
- };
-
- ir0: ir@01c21800 {
- pinctrl-names = "default";
- pinctrl-0 = <&ir0_pins_a>;
- status = "okay";
- };
-
- uart0: serial@01c28000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
- };
-
- i2c0: i2c@01c2ac00 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- axp209: pmic@34 {
- compatible = "x-powers,axp209";
- reg = <0x34>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 8>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
- };
- };
-
- gmac: ethernet@01c50000 {
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_mii_a>;
- phy = <&phy1>;
- phy-mode = "mii";
- status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
- };
+ chosen {
+ stdout-path = "serial0:115200n8";
};
leds {
gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
};
};
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&ahci_pwr_pin_a {
+ allwinner,pins = "PH2";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
- reg_usb1_vbus: usb1-vbus {
- status = "okay";
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_mii_a>;
+ phy = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
};
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
- reg_usb2_vbus: usb2-vbus {
- status = "okay";
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ led_pins_pcduino3: led_pins@0 {
+ allwinner,pins = "PH15", "PH16";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- reg_ahci_5v: ahci-5v {
- gpio = <&pio 7 2 0>;
- status = "okay";
+ key_pins_pcduino3: key_pins@0 {
+ allwinner,pins = "PH17", "PH18", "PH19";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
+
+®_ahci_5v {
+ gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Siarhei Siamashka <siarhei.siamashka@xxxxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this library; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+ model = "MSI Primo73 tablet";
+ compatible = "msi,primo73", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ soc@01c00000 {
+ mmc0: mmc@01c0f000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 0>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+ };
+
+ usbphy: phy@01c13400 {
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+ };
+
+ ehci1: usb@01c1c000 {
+ /* rtl8188etv wifi is connected here */
+ status = "okay";
+ };
+
+ pinctrl@01c20800 {
+ usb2_vbus_pin_a: usb2_vbus_pin@0 {
+ allwinner,pins = "PH12";
+ };
+ };
+
+ uart0: serial@01c28000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+ };
+ };
+
+ reg_usb2_vbus: usb2-vbus {
+ gpio = <&pio 7 12 0>; /* PH12 */
+ status = "okay";
+ };
+};
--- /dev/null
+/*
+ * Copyright 2015 Aleksei Mamlin
+ * Aleksei Mamlin <mamlinav@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Wexler TAB7200";
+ compatible = "wexler,tab7200", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@571 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <571428>;
+ };
+
+ button@761 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <761904>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Wits Pro A20 DKT for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+
+/ {
+ model = "Wits Pro A20 DKT";
+ compatible = "wits,pro-a20-dkt", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Yones Toptech BD1078 for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+
+/ {
+ model = "Yones Toptech BD1078";
+ compatible = "yones,toptech-bd1078", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
*
* Maxime Ripard <maxime.ripard@free-electrons.com>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include <dt-bindings/dma/sun4i-a10.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
interrupt-parent = <&gic>;
aliases {
ethernet0 = &gmac;
- serial0 = &uart0;
- serial1 = &uart1;
- serial2 = &uart2;
- serial3 = &uart3;
- serial4 = &uart4;
- serial5 = &uart5;
- serial6 = &uart6;
- serial7 = &uart7;
+ };
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@0 {
+ compatible = "allwinner,simple-framebuffer", "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0-hdmi";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>;
+ status = "disabled";
+ };
+
+ framebuffer@1 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0";
+ clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
+ status = "disabled";
+ };
+
+ framebuffer@2 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0-tve0";
+ clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
+ <&ahb_gates 44>;
+ status = "disabled";
+ };
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
+ clocks = <&cpu>;
+ clock-latency = <244144>; /* 8 32k periods */
+ operating-points = <
+ /* kHz uV */
+ 960000 1400000
+ 912000 1400000
+ 864000 1300000
+ 720000 1200000
+ 528000 1100000
+ 312000 1000000
+ 144000 900000
+ >;
+ #cooling-cells = <2>;
+ cooling-min-level = <0>;
+ cooling-max-level = <6>;
};
cpu@1 {
};
};
+ thermal-zones {
+ cpu_thermal {
+ /* milliseconds */
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&rtp>;
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+
+ trips {
+ cpu_alert0: cpu_alert0 {
+ /* milliCelsius */
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit: cpu_crit {
+ /* milliCelsius */
+ temperature = <100000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
memory {
reg = <0x40000000 0x80000000>;
};
timer {
compatible = "arm,armv7-timer";
- interrupts = <1 13 0xf08>,
- <1 14 0xf08>,
- <1 11 0xf08>,
- <1 10 0xf08>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
pmu {
compatible = "arm,cortex-a7-pmu", "arm,cortex-a15-pmu";
- interrupts = <0 120 4>,
- <0 121 4>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
};
clocks {
"apb0_iis2", "apb0_keypad";
};
- apb1_mux: apb1_mux@01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-mux-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
- clock-output-names = "apb1_mux";
- };
-
- apb1: apb1@01c20058 {
+ apb1: clk@01c20058 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-apb1-clk";
reg = <0x01c20058 0x4>;
- clocks = <&apb1_mux>;
+ clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
clock-output-names = "apb1";
};
};
mmc0_clk: clk@01c20088 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c20088 0x4>;
clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc0";
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
};
mmc1_clk: clk@01c2008c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c2008c 0x4>;
clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc1";
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
};
mmc2_clk: clk@01c20090 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c20090 0x4>;
clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc2";
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
};
mmc3_clk: clk@01c20094 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
reg = <0x01c20094 0x4>;
clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc3";
+ clock-output-names = "mmc3",
+ "mmc3_output",
+ "mmc3_sample";
};
ts_clk: clk@01c20098 {
mbus_clk: clk@01c2015c {
#clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
+ compatible = "allwinner,sun5i-a13-mbus-clk";
reg = <0x01c2015c 0x4>;
clocks = <&osc24M>, <&pll6 2>, <&pll5 1>;
clock-output-names = "mbus";
};
};
+ /*
+ * Note we use the address where the mmio registers start, not where
+ * the SRAM blocks start, this cannot be changed because that would be
+ * a devicetree ABI change.
+ */
soc@01c00000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ sram@00000000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00000000 0x4000>;
+ allwinner,sram-name = "A1";
+ };
+
+ sram@00004000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00004000 0x4000>;
+ allwinner,sram-name = "A2";
+ };
+
+ sram@00008000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00008000 0x4000>;
+ allwinner,sram-name = "A3-A4";
+ };
+
+ sram@00010000 {
+ compatible = "allwinner,sun4i-a10-sram";
+ reg = <0x00010000 0x1000>;
+ allwinner,sram-name = "D";
+ };
+
+ sram-controller@01c00000 {
+ compatible = "allwinner,sun4i-a10-sram-controller";
+ reg = <0x01c00000 0x30>;
+ };
+
nmi_intc: interrupt-controller@01c00030 {
compatible = "allwinner,sun7i-a20-sc-nmi";
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x01c00030 0x0c>;
- interrupts = <0 0 4>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun4i-a10-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb_gates 6>;
+ #dma-cells = <2>;
};
spi0: spi@01c05000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
- interrupts = <0 10 4>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ahb_gates 20>, <&spi0_clk>;
clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 27>,
+ <&dma SUN4I_DMA_DEDICATED 26>;
+ dma-names = "rx", "tx";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
spi1: spi@01c06000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c06000 0x1000>;
- interrupts = <0 11 4>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ahb_gates 21>, <&spi1_clk>;
clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 9>,
+ <&dma SUN4I_DMA_DEDICATED 8>;
+ dma-names = "rx", "tx";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
emac: ethernet@01c0b000 {
compatible = "allwinner,sun4i-a10-emac";
reg = <0x01c0b000 0x1000>;
- interrupts = <0 55 4>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ahb_gates 17>;
status = "disabled";
};
- mdio@01c0b080 {
+ mdio: mdio@01c0b080 {
compatible = "allwinner,sun4i-a10-mdio";
reg = <0x01c0b080 0x14>;
status = "disabled";
mmc0: mmc@01c0f000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&ahb_gates 8>, <&mmc0_clk>;
- clock-names = "ahb", "mmc";
- interrupts = <0 32 4>;
+ clocks = <&ahb_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
mmc1: mmc@01c10000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&ahb_gates 9>, <&mmc1_clk>;
- clock-names = "ahb", "mmc";
- interrupts = <0 33 4>;
+ clocks = <&ahb_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
mmc2: mmc@01c11000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&ahb_gates 10>, <&mmc2_clk>;
- clock-names = "ahb", "mmc";
- interrupts = <0 34 4>;
+ clocks = <&ahb_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
mmc3: mmc@01c12000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c12000 0x1000>;
- clocks = <&ahb_gates 11>, <&mmc3_clk>;
- clock-names = "ahb", "mmc";
- interrupts = <0 35 4>;
+ clocks = <&ahb_gates 11>,
+ <&mmc3_clk 0>,
+ <&mmc3_clk 1>,
+ <&mmc3_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
};
usbphy: phy@01c13400 {
reg-names = "phy_ctrl", "pmu1", "pmu2";
clocks = <&usb_clk 8>;
clock-names = "usb_phy";
- resets = <&usb_clk 1>, <&usb_clk 2>;
- reset-names = "usb1_reset", "usb2_reset";
+ resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>;
+ reset-names = "usb0_reset", "usb1_reset", "usb2_reset";
status = "disabled";
};
ehci0: usb@01c14000 {
compatible = "allwinner,sun7i-a20-ehci", "generic-ehci";
reg = <0x01c14000 0x100>;
- interrupts = <0 39 4>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ahb_gates 1>;
phys = <&usbphy 1>;
phy-names = "usb";
ohci0: usb@01c14400 {
compatible = "allwinner,sun7i-a20-ohci", "generic-ohci";
reg = <0x01c14400 0x100>;
- interrupts = <0 64 4>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&usb_clk 6>, <&ahb_gates 2>;
phys = <&usbphy 1>;
phy-names = "usb";
spi2: spi@01c17000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>;
- interrupts = <0 12 4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ahb_gates 22>, <&spi2_clk>;
clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 29>,
+ <&dma SUN4I_DMA_DEDICATED 28>;
+ dma-names = "rx", "tx";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
ahci: sata@01c18000 {
compatible = "allwinner,sun4i-a10-ahci";
reg = <0x01c18000 0x1000>;
- interrupts = <0 56 4>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pll6 0>, <&ahb_gates 25>;
status = "disabled";
};
ehci1: usb@01c1c000 {
compatible = "allwinner,sun7i-a20-ehci", "generic-ehci";
reg = <0x01c1c000 0x100>;
- interrupts = <0 40 4>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ahb_gates 3>;
phys = <&usbphy 2>;
phy-names = "usb";
ohci1: usb@01c1c400 {
compatible = "allwinner,sun7i-a20-ohci", "generic-ohci";
reg = <0x01c1c400 0x100>;
- interrupts = <0 65 4>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&usb_clk 7>, <&ahb_gates 4>;
phys = <&usbphy 2>;
phy-names = "usb";
spi3: spi@01c1f000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c1f000 0x1000>;
- interrupts = <0 50 4>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ahb_gates 23>, <&spi3_clk>;
clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 31>,
+ <&dma SUN4I_DMA_DEDICATED 30>;
+ dma-names = "rx", "tx";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
pio: pinctrl@01c20800 {
compatible = "allwinner,sun7i-a20-pinctrl";
reg = <0x01c20800 0x400>;
- interrupts = <0 28 4>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb0_gates 5>;
gpio-controller;
interrupt-controller;
pwm0_pins_a: pwm0@0 {
allwinner,pins = "PB2";
allwinner,function = "pwm";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
pwm1_pins_a: pwm1@0 {
allwinner,pins = "PI3";
allwinner,function = "pwm";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart0_pins_a: uart0@0 {
allwinner,pins = "PB22", "PB23";
allwinner,function = "uart0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart2_pins_a: uart2@0 {
allwinner,pins = "PI16", "PI17", "PI18", "PI19";
allwinner,function = "uart2";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart3_pins_a: uart3@0 {
+ allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart3_pins_b: uart3@1 {
+ allwinner,pins = "PH0", "PH1";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart4_pins_a: uart4@0 {
+ allwinner,pins = "PG10", "PG11";
+ allwinner,function = "uart4";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart5_pins_a: uart5@0 {
+ allwinner,pins = "PI10", "PI11";
+ allwinner,function = "uart5";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart6_pins_a: uart6@0 {
allwinner,pins = "PI12", "PI13";
allwinner,function = "uart6";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart7_pins_a: uart7@0 {
allwinner,pins = "PI20", "PI21";
allwinner,function = "uart7";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
i2c0_pins_a: i2c0@0 {
allwinner,pins = "PB0", "PB1";
allwinner,function = "i2c0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
i2c1_pins_a: i2c1@0 {
allwinner,pins = "PB18", "PB19";
allwinner,function = "i2c1";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
i2c2_pins_a: i2c2@0 {
allwinner,pins = "PB20", "PB21";
allwinner,function = "i2c2";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c3_pins_a: i2c3@0 {
+ allwinner,pins = "PI0", "PI1";
+ allwinner,function = "i2c3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
emac_pins_a: emac0@0 {
"PA11", "PA12", "PA13", "PA14",
"PA15", "PA16";
allwinner,function = "emac";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
clk_out_a_pins_a: clk_out_a@0 {
allwinner,pins = "PI12";
allwinner,function = "clk_out_a";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
clk_out_b_pins_a: clk_out_b@0 {
allwinner,pins = "PI13";
allwinner,function = "clk_out_b";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
gmac_pins_mii_a: gmac_mii@0 {
"PA11", "PA12", "PA13", "PA14",
"PA15", "PA16";
allwinner,function = "gmac";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
gmac_pins_rgmii_a: gmac_rgmii@0 {
* data lines in RGMII mode use DDR mode
* and need a higher signal drive strength
*/
- allwinner,drive = <3>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ spi0_pins_a: spi0@0 {
+ allwinner,pins = "PI10", "PI11", "PI12", "PI13", "PI14";
+ allwinner,function = "spi0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
spi1_pins_a: spi1@0 {
allwinner,pins = "PI16", "PI17", "PI18", "PI19";
allwinner,function = "spi1";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
spi2_pins_a: spi2@0 {
allwinner,pins = "PC19", "PC20", "PC21", "PC22";
allwinner,function = "spi2";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ spi2_pins_b: spi2@1 {
+ allwinner,pins = "PB14", "PB15", "PB16", "PB17";
+ allwinner,function = "spi2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
mmc0_pins_a: mmc0@0 {
allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
allwinner,function = "mmc0";
- allwinner,drive = <2>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
allwinner,pins = "PH1";
allwinner,function = "gpio_in";
- allwinner,drive = <0>;
- allwinner,pull = <1>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc2_pins_a: mmc2@0 {
+ allwinner,pins = "PC6","PC7","PC8","PC9","PC10","PC11";
+ allwinner,function = "mmc2";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
mmc3_pins_a: mmc3@0 {
allwinner,pins = "PI4","PI5","PI6","PI7","PI8","PI9";
allwinner,function = "mmc3";
- allwinner,drive = <2>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
ir0_pins_a: ir0@0 {
allwinner,pins = "PB3","PB4";
allwinner,function = "ir0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
ir1_pins_a: ir1@0 {
allwinner,pins = "PB22","PB23";
allwinner,function = "ir1";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ ps20_pins_a: ps20@0 {
+ allwinner,pins = "PI20", "PI21";
+ allwinner,function = "ps2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ ps21_pins_a: ps21@0 {
+ allwinner,pins = "PH12", "PH13";
+ allwinner,function = "ps2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
timer@01c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
- interrupts = <0 22 4>,
- <0 23 4>,
- <0 24 4>,
- <0 25 4>,
- <0 67 4>,
- <0 68 4>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc24M>;
};
rtc: rtc@01c20d00 {
compatible = "allwinner,sun7i-a20-rtc";
reg = <0x01c20d00 0x20>;
- interrupts = <0 24 4>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
};
pwm: pwm@01c20e00 {
compatible = "allwinner,sun4i-a10-ir";
clocks = <&apb0_gates 6>, <&ir0_clk>;
clock-names = "apb", "ir";
- interrupts = <0 5 4>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x01c21800 0x40>;
status = "disabled";
};
compatible = "allwinner,sun4i-a10-ir";
clocks = <&apb0_gates 7>, <&ir1_clk>;
clock-names = "apb", "ir";
- interrupts = <0 6 4>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x01c21c00 0x40>;
status = "disabled";
};
+ lradc: lradc@01c22800 {
+ compatible = "allwinner,sun4i-a10-lradc-keys";
+ reg = <0x01c22800 0x100>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
sid: eeprom@01c23800 {
compatible = "allwinner,sun7i-a20-sid";
reg = <0x01c23800 0x200>;
};
rtp: rtp@01c25000 {
- compatible = "allwinner,sun4i-a10-ts";
+ compatible = "allwinner,sun5i-a13-ts";
reg = <0x01c25000 0x100>;
- interrupts = <0 29 4>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ #thermal-sensor-cells = <0>;
};
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
- interrupts = <0 1 4>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&apb1_gates 16>;
uart1: serial@01c28400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28400 0x400>;
- interrupts = <0 2 4>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&apb1_gates 17>;
uart2: serial@01c28800 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28800 0x400>;
- interrupts = <0 3 4>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&apb1_gates 18>;
uart3: serial@01c28c00 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28c00 0x400>;
- interrupts = <0 4 4>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&apb1_gates 19>;
uart4: serial@01c29000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c29000 0x400>;
- interrupts = <0 17 4>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&apb1_gates 20>;
uart5: serial@01c29400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c29400 0x400>;
- interrupts = <0 18 4>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&apb1_gates 21>;
uart6: serial@01c29800 {
compatible = "snps,dw-apb-uart";
reg = <0x01c29800 0x400>;
- interrupts = <0 19 4>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&apb1_gates 22>;
uart7: serial@01c29c00 {
compatible = "snps,dw-apb-uart";
reg = <0x01c29c00 0x400>;
- interrupts = <0 20 4>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&apb1_gates 23>;
i2c0: i2c@01c2ac00 {
compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c";
reg = <0x01c2ac00 0x400>;
- interrupts = <0 7 4>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb1_gates 0>;
- clock-frequency = <100000>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
i2c1: i2c@01c2b000 {
compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c";
reg = <0x01c2b000 0x400>;
- interrupts = <0 8 4>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb1_gates 1>;
- clock-frequency = <100000>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
i2c2: i2c@01c2b400 {
compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c";
reg = <0x01c2b400 0x400>;
- interrupts = <0 9 4>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb1_gates 2>;
- clock-frequency = <100000>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
i2c3: i2c@01c2b800 {
compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c";
reg = <0x01c2b800 0x400>;
- interrupts = <0 88 4>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb1_gates 3>;
- clock-frequency = <100000>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
i2c4: i2c@01c2c000 {
compatible = "allwinner,sun7i-a20-i2c", "allwinner,sun4i-a10-i2c";
reg = <0x01c2c000 0x400>;
- interrupts = <0 89 4>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb1_gates 15>;
- clock-frequency = <100000>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
gmac: ethernet@01c50000 {
compatible = "allwinner,sun7i-a20-gmac";
reg = <0x01c50000 0x10000>;
- interrupts = <0 85 4>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
clocks = <&ahb_gates 49>, <&gmac_tx_clk>;
clock-names = "stmmaceth", "allwinner_gmac_tx";
hstimer@01c60000 {
compatible = "allwinner,sun7i-a20-hstimer";
reg = <0x01c60000 0x1000>;
- interrupts = <0 81 4>,
- <0 82 4>,
- <0 83 4>,
- <0 84 4>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ahb_gates 28>;
};
<0x01c86000 0x2000>;
interrupt-controller;
#interrupt-cells = <3>;
- interrupts = <1 9 0xf04>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ ps20: ps2@01c2a000 {
+ compatible = "allwinner,sun4i-a10-ps2";
+ reg = <0x01c2a000 0x400>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 6>;
+ status = "disabled";
+ };
+
+ ps21: ps2@01c2a400 {
+ compatible = "allwinner,sun4i-a10-ps2";
+ reg = <0x01c2a400 0x400>;
+ interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 7>;
+ status = "disabled";
};
};
};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * The Ippo Q8H v1.2 is almost identical to the v5, still it needs a separate
+ * dtb file since some gpio-s surrounding the wlan/bluetooth are different,
+ * and it uses different camera sensors.
+ */
+
+#include "sun8i-a23-ippo-q8h-v5.dts"
+
+/ {
+ model = "Ippo Q8H Dual Core Tablet (v1.2)";
+ compatible = "ippo,q8h-v1.2", "allwinner,sun8i-a23";
+};
--- /dev/null
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Ippo Q8H Dual Core Tablet (v5)";
+ compatible = "ippo,q8h-v5", "allwinner,sun8i-a23";
+
+ aliases {
+ serial0 = &r_uart;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ /* pull-ups and devices require PMIC regulator */
+ status = "failed";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8h>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_q8h: mmc0_cd_pin@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&r_uart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_uart_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer@0 {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "de_be0-lcd0";
+ clocks = <&pll6 0>;
+ status = "disabled";
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <24000000>;
+ arm,cpu-registers-not-fw-configured;
+ };
+
+ cpus {
+ enable-method = "allwinner,sun8i-a23";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+ };
+
+ memory {
+ reg = <0x40000000 0x40000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: clk@01c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ /* dummy clock until actually implemented */
+ pll5: pll5_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "pll5";
+ };
+
+ pll6: clk@01c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6", "pll6x2";
+ };
+
+ cpu: cpu_clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20050 0x4>;
+
+ /*
+ * PLL1 is listed twice here.
+ * While it looks suspicious, it's actually documented
+ * that way both in the datasheet and in the code from
+ * Allwinner.
+ */
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+ clock-output-names = "cpu";
+ };
+
+ axi: axi_clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-axi-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ ahb1: ahb1_clk@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun6i-a31-ahb1-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+ clock-output-names = "ahb1";
+ };
+
+ apb1: apb1_clk@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb1>;
+ clock-output-names = "apb1";
+ };
+
+ ahb1_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-a23-ahb1-gates-clk";
+ reg = <0x01c20060 0x8>;
+ clocks = <&ahb1>;
+ clock-output-names = "ahb1_mipidsi", "ahb1_dma",
+ "ahb1_mmc0", "ahb1_mmc1", "ahb1_mmc2",
+ "ahb1_nand", "ahb1_sdram",
+ "ahb1_hstimer", "ahb1_spi0",
+ "ahb1_spi1", "ahb1_otg", "ahb1_ehci",
+ "ahb1_ohci", "ahb1_ve", "ahb1_lcd",
+ "ahb1_csi", "ahb1_be", "ahb1_fe",
+ "ahb1_gpu", "ahb1_spinlock",
+ "ahb1_drc";
+ };
+
+ apb1_gates: clk@01c20068 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-a23-apb1-gates-clk";
+ reg = <0x01c20068 0x4>;
+ clocks = <&apb1>;
+ clock-output-names = "apb1_codec", "apb1_pio",
+ "apb1_daudio0", "apb1_daudio1";
+ };
+
+ apb2: clk@01c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+ clock-output-names = "apb2";
+ };
+
+ apb2_gates: clk@01c2006c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-a23-apb2-gates-clk";
+ reg = <0x01c2006c 0x4>;
+ clocks = <&apb2>;
+ clock-output-names = "apb2_i2c0", "apb2_i2c1",
+ "apb2_i2c2", "apb2_uart0",
+ "apb2_uart1", "apb2_uart2",
+ "apb2_uart3", "apb2_uart4";
+ };
+
+ mmc0_clk: clk@01c20088 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk@01c2008c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk@01c20090 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 0>;
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
+ };
+
+ mbus_clk: clk@01c2015c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-mbus-clk";
+ reg = <0x01c2015c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5>;
+ clock-output-names = "mbus";
+ };
+ };
+
+ soc@01c00000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun8i-a23-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb1_gates 6>;
+ resets = <&ahb1_rst 6>;
+ #dma-cells = <1>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ahb1_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb1_rst 8>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ahb1_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb1_rst 9>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ahb1_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb1_rst 10>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pio: pinctrl@01c20800 {
+ compatible = "allwinner,sun8i-a23-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 5>;
+ gpio-controller;
+ interrupt-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #gpio-cells = <3>;
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PF2", "PF4";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0","PF1","PF2","PF3","PF4","PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc1_pins_a: mmc1@0 {
+ allwinner,pins = "PG0","PG1","PG2","PG3","PG4","PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PH2", "PH3";
+ allwinner,function = "i2c0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PH4", "PH5";
+ allwinner,function = "i2c1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PE12", "PE13";
+ allwinner,function = "i2c2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ ahb1_rst: reset@01c202c0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202c0 0xc>;
+ };
+
+ apb1_rst: reset@01c202d0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d0 0x4>;
+ };
+
+ apb2_rst: reset@01c202d8 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d8 0x4>;
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ wdt0: watchdog@01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ lradc: lradc@01c22800 {
+ compatible = "allwinner,sun4i-a10-lradc-keys";
+ reg = <0x01c22800 0x100>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ uart0: serial@01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 16>;
+ resets = <&apb2_rst 16>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 17>;
+ resets = <&apb2_rst 17>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 18>;
+ resets = <&apb2_rst 18>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 19>;
+ resets = <&apb2_rst 19>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart4: serial@01c29000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb2_gates 20>;
+ resets = <&apb2_rst 20>;
+ dmas = <&dma 10>, <&dma 10>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2c0: i2c@01c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb2_gates 0>;
+ resets = <&apb2_rst 0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@01c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb2_gates 1>;
+ resets = <&apb2_rst 1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@01c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb2_gates 2>;
+ resets = <&apb2_rst 2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ gic: interrupt-controller@01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ rtc: rtc@01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ prcm@01f01400 {
+ compatible = "allwinner,sun8i-a23-prcm";
+ reg = <0x01f01400 0x200>;
+
+ ar100: ar100_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "ar100";
+ };
+
+ ahb0: ahb0_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&ar100>;
+ clock-output-names = "ahb0";
+ };
+
+ apb0: apb0_clk {
+ compatible = "allwinner,sun8i-a23-apb0-clk";
+ #clock-cells = <0>;
+ clocks = <&ahb0>;
+ clock-output-names = "apb0";
+ };
+
+ apb0_gates: apb0_gates_clk {
+ compatible = "allwinner,sun8i-a23-apb0-gates-clk";
+ #clock-cells = <1>;
+ clocks = <&apb0>;
+ clock-output-names = "apb0_pio", "apb0_timer",
+ "apb0_rsb", "apb0_uart",
+ "apb0_i2c";
+ };
+
+ apb0_rst: apb0_rst {
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ #reset-cells = <1>;
+ };
+ };
+
+ cpucfg@01f01c00 {
+ compatible = "allwinner,sun8i-a23-cpuconfig";
+ reg = <0x01f01c00 0x300>;
+ };
+
+ r_uart: serial@01f02800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01f02800 0x400>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb0_gates 4>;
+ resets = <&apb0_rst 4>;
+ status = "disabled";
+ };
+
+ r_pio: pinctrl@01f02c00 {
+ compatible = "allwinner,sun8i-a23-r-pinctrl";
+ reg = <0x01f02c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 0>;
+ resets = <&apb0_rst 0>;
+ gpio-controller;
+ interrupt-controller;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #gpio-cells = <3>;
+
+ r_uart_pins_a: r_uart@0 {
+ allwinner,pins = "PL2", "PL3";
+ allwinner,function = "s_uart";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Astar MID756 for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+
+/ {
+ model = "Astar MID756";
+ compatible = "astar,mid756", "allwinner,sun8i-a23";
+
+ aliases {
+ serial0 = &r_uart;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&r_uart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_uart_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Minimal dts file for the Ippo Q8H V1.2 (A33, 1024x600) for u-boot only
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+
+/ {
+ model = "Ippo Q8H V1.2 (A33, 1024x600)";
+ compatible = "ippo,q8h-v1.2-a33-lcd1024x600", "allwinner,sun8i-a23";
+
+ aliases {
+ serial0 = &r_uart;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&r_uart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_uart_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2015 Tyler Baker
+ *
+ * Tyler Baker <tyler.baker@linaro.org>
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun9i-a80.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Cubietech Cubieboard4";
+ compatible = "cubietech,a80-cubieboard4", "allwinner,sun9i-a80";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+};
+
+&pio {
+ mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
+ allwinner,pins = "PH18";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun9i-a80.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Merrii A80 Optimus Board";
+ compatible = "merrii,a80-optimus", "allwinner,sun9i-a80";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_optimus>;
+
+ /* The LED names match those found on the board */
+
+ led2 {
+ label = "optimus:led2:usr";
+ gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* led3 is on PM15, in R_PIO */
+
+ led4 {
+ label = "optimus:led4:usr";
+ gpios = <&pio 7 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_usb3_vbus: usb3-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb3_vbus_pin_optimus>;
+ regulator-name = "usb3-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins_a>;
+ status = "okay";
+};
+
+&i2c3_pins_a {
+ /* Enable internal pull-up */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&pio {
+ led_pins_optimus: led-pins@0 {
+ allwinner,pins = "PH0", "PH1";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_optimus: mmc0_cd_pin@0 {
+ allwinner,pins = "PH18";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_optimus: usb1_vbus_pin@1 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb3_vbus_pin_optimus: usb3_vbus_pin@1 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+®_usb1_vbus {
+ pinctrl-0 = <&usb1_vbus_pin_optimus>;
+ gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
+&uart4_pins_a {
+ /* Enable internal pull-up */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&usbphy1 {
+ phy-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
+&usbphy2 {
+ status = "okay";
+};
+
+&usbphy3 {
+ phy-supply = <®_usb3_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton64.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0x0>;
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0x1>;
+ };
+
+ cpu2: cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0x2>;
+ };
+
+ cpu3: cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0x3>;
+ };
+
+ cpu4: cpu@100 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <0x100>;
+ };
+
+ cpu5: cpu@101 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <0x101>;
+ };
+
+ cpu6: cpu@102 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <0x102>;
+ };
+
+ cpu7: cpu@103 {
+ compatible = "arm,cortex-a15";
+ device_type = "cpu";
+ reg = <0x103>;
+ };
+ };
+
+ memory {
+ /* 8GB max. with LPAE */
+ reg = <0 0x20000000 0x02 0>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <24000000>;
+ arm,cpu-registers-not-fw-configured;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /*
+ * map 64 bit address range down to 32 bits,
+ * as the peripherals are all under 512MB.
+ */
+ ranges = <0 0 0 0x20000000>;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ usb_mod_clk: clk@00a08000 {
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun9i-a80-usb-mod-clk";
+ reg = <0x00a08000 0x4>;
+ clocks = <&ahb1_gates 1>;
+ clock-output-names = "usb0_ahb", "usb_ohci0",
+ "usb1_ahb", "usb_ohci1",
+ "usb2_ahb", "usb_ohci2";
+ };
+
+ usb_phy_clk: clk@00a08004 {
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun9i-a80-usb-phy-clk";
+ reg = <0x00a08004 0x4>;
+ clocks = <&ahb1_gates 1>;
+ clock-output-names = "usb_phy0", "usb_hsic1_480M",
+ "usb_phy1", "usb_hsic2_480M",
+ "usb_phy2", "usb_hsic_12M";
+ };
+
+ pll4: clk@0600000c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-pll4-clk";
+ reg = <0x0600000c 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll4";
+ };
+
+ pll12: clk@0600002c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-pll4-clk";
+ reg = <0x0600002c 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll12";
+ };
+
+ gt_clk: clk@0600005c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-gt-clk";
+ reg = <0x0600005c 0x4>;
+ clocks = <&osc24M>, <&pll4>, <&pll12>, <&pll12>;
+ clock-output-names = "gt";
+ };
+
+ ahb0: clk@06000060 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-ahb-clk";
+ reg = <0x06000060 0x4>;
+ clocks = <>_clk>, <&pll4>, <&pll12>, <&pll12>;
+ clock-output-names = "ahb0";
+ };
+
+ ahb1: clk@06000064 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-ahb-clk";
+ reg = <0x06000064 0x4>;
+ clocks = <>_clk>, <&pll4>, <&pll12>, <&pll12>;
+ clock-output-names = "ahb1";
+ };
+
+ ahb2: clk@06000068 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-ahb-clk";
+ reg = <0x06000068 0x4>;
+ clocks = <>_clk>, <&pll4>, <&pll12>, <&pll12>;
+ clock-output-names = "ahb2";
+ };
+
+ apb0: clk@06000070 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-apb0-clk";
+ reg = <0x06000070 0x4>;
+ clocks = <&osc24M>, <&pll4>;
+ clock-output-names = "apb0";
+ };
+
+ apb1: clk@06000074 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-apb1-clk";
+ reg = <0x06000074 0x4>;
+ clocks = <&osc24M>, <&pll4>;
+ clock-output-names = "apb1";
+ };
+
+ cci400_clk: clk@06000078 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun9i-a80-gt-clk";
+ reg = <0x06000078 0x4>;
+ clocks = <&osc24M>, <&pll4>, <&pll12>, <&pll12>;
+ clock-output-names = "cci400";
+ };
+
+ mmc0_clk: clk@06000410 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-mmc-clk";
+ reg = <0x06000410 0x4>;
+ clocks = <&osc24M>, <&pll4>;
+ clock-output-names = "mmc0", "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk@06000414 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-mmc-clk";
+ reg = <0x06000414 0x4>;
+ clocks = <&osc24M>, <&pll4>;
+ clock-output-names = "mmc1", "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk@06000418 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-mmc-clk";
+ reg = <0x06000418 0x4>;
+ clocks = <&osc24M>, <&pll4>;
+ clock-output-names = "mmc2", "mmc2_output",
+ "mmc2_sample";
+ };
+
+ mmc3_clk: clk@0600041c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-mmc-clk";
+ reg = <0x0600041c 0x4>;
+ clocks = <&osc24M>, <&pll4>;
+ clock-output-names = "mmc3", "mmc3_output",
+ "mmc3_sample";
+ };
+
+ ahb0_gates: clk@06000580 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-ahb0-gates-clk";
+ reg = <0x06000580 0x4>;
+ clocks = <&ahb0>;
+ clock-indices = <0>, <1>, <3>, <5>, <8>, <12>, <13>,
+ <14>, <15>, <16>, <18>, <20>, <21>,
+ <22>, <23>;
+ clock-output-names = "ahb0_fd", "ahb0_ve", "ahb0_gpu",
+ "ahb0_ss", "ahb0_sd", "ahb0_nand1",
+ "ahb0_nand0", "ahb0_sdram",
+ "ahb0_mipi_hsi", "ahb0_sata", "ahb0_ts",
+ "ahb0_spi0","ahb0_spi1", "ahb0_spi2",
+ "ahb0_spi3";
+ };
+
+ ahb1_gates: clk@06000584 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-ahb1-gates-clk";
+ reg = <0x06000584 0x4>;
+ clocks = <&ahb1>;
+ clock-indices = <0>, <1>, <17>, <21>, <22>, <23>, <24>;
+ clock-output-names = "ahb1_usbotg", "ahb1_usbhci",
+ "ahb1_gmac", "ahb1_msgbox",
+ "ahb1_spinlock", "ahb1_hstimer",
+ "ahb1_dma";
+ };
+
+ ahb2_gates: clk@06000588 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-ahb2-gates-clk";
+ reg = <0x06000588 0x4>;
+ clocks = <&ahb2>;
+ clock-indices = <0>, <1>, <2>, <4>, <5>, <7>, <8>,
+ <11>;
+ clock-output-names = "ahb2_lcd0", "ahb2_lcd1",
+ "ahb2_edp", "ahb2_csi", "ahb2_hdmi",
+ "ahb2_de", "ahb2_mp", "ahb2_mipi_dsi";
+ };
+
+ apb0_gates: clk@06000590 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-apb0-gates-clk";
+ reg = <0x06000590 0x4>;
+ clocks = <&apb0>;
+ clock-indices = <1>, <5>, <11>, <12>, <13>, <15>,
+ <17>, <18>, <19>;
+ clock-output-names = "apb0_spdif", "apb0_pio",
+ "apb0_ac97", "apb0_i2s0", "apb0_i2s1",
+ "apb0_lradc", "apb0_gpadc", "apb0_twd",
+ "apb0_cirtx";
+ };
+
+ apb1_gates: clk@06000594 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun9i-a80-apb1-gates-clk";
+ reg = <0x06000594 0x4>;
+ clocks = <&apb1>;
+ clock-indices = <0>, <1>, <2>, <3>, <4>,
+ <16>, <17>, <18>, <19>, <20>, <21>;
+ clock-output-names = "apb1_i2c0", "apb1_i2c1",
+ "apb1_i2c2", "apb1_i2c3", "apb1_i2c4",
+ "apb1_uart0", "apb1_uart1",
+ "apb1_uart2", "apb1_uart3",
+ "apb1_uart4", "apb1_uart5";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /*
+ * map 64 bit address range down to 32 bits,
+ * as the peripherals are all under 512MB.
+ */
+ ranges = <0 0 0 0x20000000>;
+
+ ehci0: usb@00a00000 {
+ compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
+ reg = <0x00a00000 0x100>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usb_mod_clk 1>;
+ resets = <&usb_mod_clk 17>;
+ phys = <&usbphy1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@00a00400 {
+ compatible = "allwinner,sun9i-a80-ohci", "generic-ohci";
+ reg = <0x00a00400 0x100>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usb_mod_clk 1>, <&usb_mod_clk 2>;
+ resets = <&usb_mod_clk 17>;
+ phys = <&usbphy1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usbphy1: phy@00a00800 {
+ compatible = "allwinner,sun9i-a80-usb-phy";
+ reg = <0x00a00800 0x4>;
+ clocks = <&usb_phy_clk 1>;
+ clock-names = "phy";
+ resets = <&usb_phy_clk 17>;
+ reset-names = "phy";
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ ehci1: usb@00a01000 {
+ compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
+ reg = <0x00a01000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usb_mod_clk 3>;
+ resets = <&usb_mod_clk 18>;
+ phys = <&usbphy2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usbphy2: phy@00a01800 {
+ compatible = "allwinner,sun9i-a80-usb-phy";
+ reg = <0x00a01800 0x4>;
+ clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>,
+ <&usb_phy_clk 3>;
+ clock-names = "hsic_480M", "hsic_12M", "phy";
+ resets = <&usb_phy_clk 18>, <&usb_phy_clk 19>;
+ reset-names = "hsic", "phy";
+ status = "disabled";
+ #phy-cells = <0>;
+ /* usb1 is always used with HSIC */
+ phy_type = "hsic";
+ };
+
+ ehci2: usb@00a02000 {
+ compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
+ reg = <0x00a02000 0x100>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usb_mod_clk 5>;
+ resets = <&usb_mod_clk 19>;
+ phys = <&usbphy3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb@00a02400 {
+ compatible = "allwinner,sun9i-a80-ohci", "generic-ohci";
+ reg = <0x00a02400 0x100>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usb_mod_clk 5>, <&usb_mod_clk 6>;
+ resets = <&usb_mod_clk 19>;
+ phys = <&usbphy3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usbphy3: phy@00a02800 {
+ compatible = "allwinner,sun9i-a80-usb-phy";
+ reg = <0x00a02800 0x4>;
+ clocks = <&usb_phy_clk 4>, <&usb_phy_clk 10>,
+ <&usb_phy_clk 5>;
+ clock-names = "hsic_480M", "hsic_12M", "phy";
+ resets = <&usb_phy_clk 20>, <&usb_phy_clk 21>;
+ reset-names = "hsic", "phy";
+ status = "disabled";
+ #phy-cells = <0>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&mmc_config_clk 0>, <&mmc0_clk 0>,
+ <&mmc0_clk 1>, <&mmc0_clk 2>;
+ clock-names = "ahb", "mmc", "output", "sample";
+ resets = <&mmc_config_clk 0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&mmc_config_clk 1>, <&mmc1_clk 0>,
+ <&mmc1_clk 1>, <&mmc1_clk 2>;
+ clock-names = "ahb", "mmc", "output", "sample";
+ resets = <&mmc_config_clk 1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&mmc_config_clk 2>, <&mmc2_clk 0>,
+ <&mmc2_clk 1>, <&mmc2_clk 2>;
+ clock-names = "ahb", "mmc", "output", "sample";
+ resets = <&mmc_config_clk 2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc3: mmc@01c12000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c12000 0x1000>;
+ clocks = <&mmc_config_clk 3>, <&mmc3_clk 0>,
+ <&mmc3_clk 1>, <&mmc3_clk 2>;
+ clock-names = "ahb", "mmc", "output", "sample";
+ resets = <&mmc_config_clk 3>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc_config_clk: clk@01c13000 {
+ compatible = "allwinner,sun9i-a80-mmc-config-clk";
+ reg = <0x01c13000 0x10>;
+ clocks = <&ahb0_gates 8>;
+ clock-names = "ahb";
+ resets = <&ahb0_resets 8>;
+ reset-names = "ahb";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ clock-output-names = "mmc0_config", "mmc1_config",
+ "mmc2_config", "mmc3_config";
+ };
+
+ gic: interrupt-controller@01c41000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c41000 0x1000>,
+ <0x01c42000 0x1000>,
+ <0x01c44000 0x2000>,
+ <0x01c46000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ ahb0_resets: reset@060005a0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x060005a0 0x4>;
+ };
+
+ ahb1_resets: reset@060005a4 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x060005a4 0x4>;
+ };
+
+ ahb2_resets: reset@060005a8 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x060005a8 0x4>;
+ };
+
+ apb0_resets: reset@060005b0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x060005b0 0x4>;
+ };
+
+ apb1_resets: reset@060005b4 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x060005b4 0x4>;
+ };
+
+ timer@06000c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x06000c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&osc24M>;
+ };
+
+ pio: pinctrl@06000800 {
+ compatible = "allwinner,sun9i-a80-pinctrl";
+ reg = <0x06000800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 5>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #size-cells = <0>;
+ #gpio-cells = <3>;
+
+ i2c3_pins_a: i2c3@0 {
+ allwinner,pins = "PG10", "PG11";
+ allwinner,function = "i2c3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins: mmc0 {
+ allwinner,pins = "PF0", "PF1" ,"PF2", "PF3",
+ "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc2_8bit_pins: mmc2_8bit {
+ allwinner,pins = "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11", "PC12",
+ "PC13", "PC14", "PC15";
+ allwinner,function = "mmc2";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PH12", "PH13";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart4_pins_a: uart4@0 {
+ allwinner,pins = "PG12", "PG13", "PG14", "PG15";
+ allwinner,function = "uart4";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ uart0: serial@07000000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07000000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 16>;
+ resets = <&apb1_resets 16>;
+ status = "disabled";
+ };
+
+ uart1: serial@07000400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07000400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 17>;
+ resets = <&apb1_resets 17>;
+ status = "disabled";
+ };
+
+ uart2: serial@07000800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07000800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 18>;
+ resets = <&apb1_resets 18>;
+ status = "disabled";
+ };
+
+ uart3: serial@07000c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07000c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 19>;
+ resets = <&apb1_resets 19>;
+ status = "disabled";
+ };
+
+ uart4: serial@07001000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07001000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 20>;
+ resets = <&apb1_resets 20>;
+ status = "disabled";
+ };
+
+ uart5: serial@07001400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07001400 0x400>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&apb1_gates 21>;
+ resets = <&apb1_resets 21>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@07002800 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x07002800 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 0>;
+ resets = <&apb1_resets 0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@07002c00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x07002c00 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 1>;
+ resets = <&apb1_resets 1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@07003000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x07003000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 2>;
+ resets = <&apb1_resets 2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@07003400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x07003400 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 3>;
+ resets = <&apb1_resets 3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c4: i2c@07003800 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x07003800 0x400>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb1_gates 4>;
+ resets = <&apb1_resets 4>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ r_wdt: watchdog@08001000 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x08001000 0x20>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ r_uart: serial@08002800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x08002800 0x400>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+ };
+};
*
* Copyright 2014 - Hans de Goede <hdegoede@redhat.com>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
-/ {
- soc@01c00000 {
- pio: pinctrl@01c20800 {
- ahci_pwr_pin_a: ahci_pwr_pin@0 {
- allwinner,pins = "PB8";
- allwinner,function = "gpio_out";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
- usb1_vbus_pin_a: usb1_vbus_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_out";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
+&pio {
+ ahci_pwr_pin_a: ahci_pwr_pin@0 {
+ allwinner,pins = "PB8";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_pin_a: usb0_vbus_pin@0 {
+ allwinner,pins = "PB9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
- usb2_vbus_pin_a: usb2_vbus_pin@0 {
- allwinner,pins = "PH3";
- allwinner,function = "gpio_out";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
- };
+ usb1_vbus_pin_a: usb1_vbus_pin@0 {
+ allwinner,pins = "PH6";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ usb2_vbus_pin_a: usb2_vbus_pin@0 {
+ allwinner,pins = "PH3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+/ {
reg_ahci_5v: ahci-5v {
compatible = "regulator-fixed";
pinctrl-names = "default";
regulator-name = "ahci-5v";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
enable-active-high;
- gpio = <&pio 1 8 0>;
+ gpio = <&pio 1 8 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+
+ reg_usb0_vbus: usb0-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_vbus_pin_a>;
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 1 9 GPIO_ACTIVE_HIGH>;
status = "disabled";
};
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
- gpio = <&pio 7 6 0>;
+ gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>;
status = "disabled";
};
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
- gpio = <&pio 7 3 0>;
+ gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>;
status = "disabled";
};
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
+
+ reg_vcc5v0: vcc5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
};
u32 mipi_pll_cfg; /* 0x40 MIPI pll control */
u32 pll9_cfg; /* 0x44 pll9 control */
u32 pll10_cfg; /* 0x48 pll10 control */
- u32 reserved8;
+ u32 pll11_cfg; /* 0x4c pll11 (ddr1) control (A33 only) */
u32 cpu_axi_cfg; /* 0x50 CPU/AXI divide ratio */
u32 ahb1_apb1_div; /* 0x54 AHB1/APB1 divide ratio */
u32 apb2_div; /* 0x58 APB2 divide ratio */
u32 reserved12[7];
u32 mdfs_clk_cfg; /* 0xf0 MDFS clock control */
u32 dram_clk_cfg; /* 0xf4 DRAM configuration clock control */
- u32 reserved13[2];
+ u32 dram_pll_cfg; /* 0xf8 PLL_DDR cfg register, A33 only */
+ u32 mbus_reset; /* 0xfc MBUS reset control, A33 only */
u32 dram_clk_gate; /* 0x100 DRAM module gating */
u32 be0_clk_cfg; /* 0x104 BE0 module clock */
u32 be1_clk_cfg; /* 0x108 BE1 module clock */
u32 mipi_pattern_cfg; /* 0x2a0 MIPI Pattern config */
u32 pll9_pattern_cfg; /* 0x2a4 PLL9 Pattern config */
u32 pll10_pattern_cfg; /* 0x2a8 PLL10 Pattern config */
- u32 reserved22[5];
+ u32 pll11_pattern_cfg0; /* 0x2ac PLL11 Pattern config0, A33 only */
+ u32 pll11_pattern_cfg1; /* 0x2b0 PLL11 Pattern config0, A33 only */
+ u32 reserved22[3];
u32 ahb_reset0_cfg; /* 0x2c0 AHB1 Reset 0 config */
u32 ahb_reset1_cfg; /* 0x2c4 AHB1 Reset 1 config */
u32 ahb_reset2_cfg; /* 0x2c8 AHB1 Reset 2 config */
#define CCM_PLL6_CTRL_K_SHIFT 4
#define CCM_PLL6_CTRL_K_MASK (0x3 << CCM_PLL6_CTRL_K_SHIFT)
+#define CCM_PLL11_CTRL_N(n) ((((n) - 1) & 0x3f) << 8)
+#define CCM_PLL11_CTRL_SIGMA_DELTA_EN (0x1 << 24)
+#define CCM_PLL11_CTRL_UPD (0x1 << 30)
+#define CCM_PLL11_CTRL_EN (0x1 << 31)
+
#define AHB1_ABP1_DIV_DEFAULT 0x00002020
#define AXI_GATE_OFFSET_DRAM 0
/* ahb_gate1 offsets */
#define AHB_GATE_OFFSET_DRC0 25
+#define AHB_GATE_OFFSET_DE_FE0 14
#define AHB_GATE_OFFSET_DE_BE0 12
#define AHB_GATE_OFFSET_HDMI 11
#define AHB_GATE_OFFSET_LCD1 5
#define MDFS_CLK_DEFAULT 0x81000002 /* PLL6 / 3 */
+#define CCM_DRAMCLK_CFG_DIV(x) ((x - 1) << 0)
+#define CCM_DRAMCLK_CFG_DIV_MASK (0xf << 0)
#define CCM_DRAMCLK_CFG_DIV0(x) ((x - 1) << 8)
#define CCM_DRAMCLK_CFG_DIV0_MASK (0xf << 8)
#define CCM_DRAMCLK_CFG_UPD (0x1 << 16)
#define CCM_DRAMCLK_CFG_RST (0x1 << 31)
+#define CCM_DRAMPLL_CFG_SRC_PLL5 (0x0 << 16) /* Select PLL5 (DDR0) */
+#define CCM_DRAMPLL_CFG_SRC_PLL11 (0x1 << 16) /* Select PLL11 (DDR1) */
+#define CCM_DRAMPLL_CFG_SRC_MASK (0x1 << 16)
+
+#define CCM_MBUS_RESET_RESET (0x1 << 31)
+
+#define CCM_DRAM_GATE_OFFSET_DE_FE0 24
+#define CCM_DRAM_GATE_OFFSET_DE_FE1 25
#define CCM_DRAM_GATE_OFFSET_DE_BE0 26
+#define CCM_DRAM_GATE_OFFSET_DE_BE1 27
#define CCM_LCD_CH0_CTRL_PLL3 (0 << 24)
#define CCM_LCD_CH0_CTRL_PLL7 (1 << 24)
#else
#define MBUS_CLK_DEFAULT 0x81000003 /* PLL6 / 4 */
#endif
+#define MBUS_CLK_GATE (0x1 << 31)
#define CCM_PLL5_PATTERN 0xd1303333
+#define CCM_PLL11_PATTERN 0xf5860000
/* ahb_reset0 offsets */
#define AHB_RESET_OFFSET_GMAC 17
#define AHB_RESET_OFFSET_SS 5
/* ahb_reset1 offsets */
+#define AHB_RESET_OFFSET_SAT 26
#define AHB_RESET_OFFSET_DRC0 25
+#define AHB_RESET_OFFSET_DE_FE0 14
#define AHB_RESET_OFFSET_DE_BE0 12
#define AHB_RESET_OFFSET_HDMI 11
#define AHB_RESET_OFFSET_LCD1 5
void clock_set_pll1(unsigned int hz);
void clock_set_pll3(unsigned int hz);
void clock_set_pll5(unsigned int clk, bool sigma_delta_enable);
+void clock_set_pll11(unsigned int clk, bool sigma_delta_enable);
unsigned int clock_get_pll6(void);
#endif
#define SUNXI_MMC1_BASE 0x01c10000
#define SUNXI_MMC2_BASE 0x01c11000
#define SUNXI_MMC3_BASE 0x01c12000
-#if !defined CONFIG_MACH_SUN6I && !defined CONFIG_MACH_SUN8I
+#ifdef CONFIG_SUNXI_GEN_SUN4I
#define SUNXI_USB0_BASE 0x01c13000
#define SUNXI_USB1_BASE 0x01c14000
#endif
#define SUNXI_HDMI_BASE 0x01c16000
#define SUNXI_SPI2_BASE 0x01c17000
#define SUNXI_SATA_BASE 0x01c18000
-#if !defined CONFIG_MACH_SUN6I && !defined CONFIG_MACH_SUN8I
+#ifdef CONFIG_SUNXI_GEN_SUN4I
#define SUNXI_PATA_BASE 0x01c19000
#define SUNXI_ACE_BASE 0x01c1a000
#define SUNXI_TVE1_BASE 0x01c1b000
#define SUNXI_USB2_BASE 0x01c1c000
-#else
+#endif
+#ifdef CONFIG_SUNXI_GEN_SUN6I
#define SUNXI_USB0_BASE 0x01c19000
#define SUNXI_USB1_BASE 0x01c1a000
#define SUNXI_USB2_BASE 0x01c1b000
/* dram regs definition */
#if defined(CONFIG_MACH_SUN6I)
#include <asm/arch/dram_sun6i.h>
-#elif defined(CONFIG_MACH_SUN8I)
-#include <asm/arch/dram_sun8i.h>
+#elif defined(CONFIG_MACH_SUN8I_A23)
+#include <asm/arch/dram_sun8i_a23.h>
+#elif defined(CONFIG_MACH_SUN8I_A33)
+#include <asm/arch/dram_sun8i_a33.h>
#else
#include <asm/arch/dram_sun4i.h>
#endif
--- /dev/null
+/*
+ * Sun8i platform dram controller register and constant defines
+ *
+ * (C) Copyright 2007-2015 Allwinner Technology Co.
+ * Jerry Wang <wangflord@allwinnertech.com>
+ * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * (C) Copyright 2014-2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _SUNXI_DRAM_SUN8I_A33_H
+#define _SUNXI_DRAM_SUN8I_A33_H
+
+struct sunxi_mctl_com_reg {
+ u32 cr; /* 0x00 */
+ u32 ccr; /* 0x04 controller configuration register */
+ u32 dbgcr; /* 0x08 */
+ u8 res0[0x4]; /* 0x0c */
+ u32 mcr0_0; /* 0x10 */
+ u32 mcr1_0; /* 0x14 */
+ u32 mcr0_1; /* 0x18 */
+ u32 mcr1_1; /* 0x1c */
+ u32 mcr0_2; /* 0x20 */
+ u32 mcr1_2; /* 0x24 */
+ u32 mcr0_3; /* 0x28 */
+ u32 mcr1_3; /* 0x2c */
+ u32 mcr0_4; /* 0x30 */
+ u32 mcr1_4; /* 0x34 */
+ u32 mcr0_5; /* 0x38 */
+ u32 mcr1_5; /* 0x3c */
+ u32 mcr0_6; /* 0x40 */
+ u32 mcr1_6; /* 0x44 */
+ u32 mcr0_7; /* 0x48 */
+ u32 mcr1_7; /* 0x4c */
+ u32 mcr0_8; /* 0x50 */
+ u32 mcr1_8; /* 0x54 */
+ u32 mcr0_9; /* 0x58 */
+ u32 mcr1_9; /* 0x5c */
+ u32 mcr0_10; /* 0x60 */
+ u32 mcr1_10; /* 0x64 */
+ u32 mcr0_11; /* 0x68 */
+ u32 mcr1_11; /* 0x6c */
+ u32 mcr0_12; /* 0x70 */
+ u32 mcr1_12; /* 0x74 */
+ u32 mcr0_13; /* 0x78 */
+ u32 mcr1_13; /* 0x7c */
+ u32 mcr0_14; /* 0x80 */
+ u32 mcr1_14; /* 0x84 */
+ u32 mcr0_15; /* 0x88 */
+ u32 mcr1_15; /* 0x8c */
+ u32 bwcr; /* 0x90 */
+ u32 maer; /* 0x94 */
+ u32 mapr; /* 0x98 */
+ u32 mcgcr; /* 0x9c */
+ u32 bwctr; /* 0xa0 */
+ u8 res2[0x8]; /* 0xa4 */
+ u32 swoffr; /* 0xac */
+ u8 res3[0x10]; /* 0xb0 */
+ u32 swonr; /* 0xc0 */
+ u8 res4[0x3c]; /* 0xc4 */
+ u32 mdfscr; /* 0x100 */
+ u32 mdfsmer; /* 0x104 */
+};
+
+struct sunxi_mctl_ctl_reg {
+ u32 pir; /* 0x00 */
+ u32 pwrctl; /* 0x04 */
+ u32 mrctrl0; /* 0x08 */
+ u32 clken; /* 0x0c */
+ u32 pgsr0; /* 0x10 */
+ u32 pgsr1; /* 0x14 */
+ u32 statr; /* 0x18 */
+ u8 res1[0x14]; /* 0x1c */
+ u32 mr0; /* 0x30 */
+ u32 mr1; /* 0x34 */
+ u32 mr2; /* 0x38 */
+ u32 mr3; /* 0x3c */
+ u32 pllgcr; /* 0x40 */
+ u32 ptr0; /* 0x44 */
+ u32 ptr1; /* 0x48 */
+ u32 ptr2; /* 0x4c */
+ u32 ptr3; /* 0x50 */
+ u32 ptr4; /* 0x54 */
+ u32 dramtmg0; /* 0x58 dram timing parameters register 0 */
+ u32 dramtmg1; /* 0x5c dram timing parameters register 1 */
+ u32 dramtmg2; /* 0x60 dram timing parameters register 2 */
+ u32 dramtmg3; /* 0x64 dram timing parameters register 3 */
+ u32 dramtmg4; /* 0x68 dram timing parameters register 4 */
+ u32 dramtmg5; /* 0x6c dram timing parameters register 5 */
+ u32 dramtmg6; /* 0x70 dram timing parameters register 6 */
+ u32 dramtmg7; /* 0x74 dram timing parameters register 7 */
+ u32 dramtmg8; /* 0x78 dram timing parameters register 8 */
+ u32 odtcfg; /* 0x7c */
+ u32 pitmg0; /* 0x80 */
+ u32 pitmg1; /* 0x84 */
+ u8 res2[0x4]; /* 0x88 */
+ u32 rfshctl0; /* 0x8c */
+ u32 rfshtmg; /* 0x90 */
+ u32 rfshctl1; /* 0x94 */
+ u32 pwrtmg; /* 0x98 */
+ u8 res3[0x20]; /* 0x9c */
+ u32 dqsgmr; /* 0xbc */
+ u32 dtcr; /* 0xc0 */
+ u32 dtar0; /* 0xc4 */
+ u32 dtar1; /* 0xc8 */
+ u32 dtar2; /* 0xcc */
+ u32 dtar3; /* 0xd0 */
+ u32 dtdr0; /* 0xd4 */
+ u32 dtdr1; /* 0xd8 */
+ u32 dtmr0; /* 0xdc */
+ u32 dtmr1; /* 0xe0 */
+ u32 dtbmr; /* 0xe4 */
+ u32 catr0; /* 0xe8 */
+ u32 catr1; /* 0xec */
+ u32 dtedr0; /* 0xf0 */
+ u32 dtedr1; /* 0xf4 */
+ u8 res4[0x8]; /* 0xf8 */
+ u32 pgcr0; /* 0x100 */
+ u32 pgcr1; /* 0x104 */
+ u32 pgcr2; /* 0x108 */
+ u8 res5[0x4]; /* 0x10c */
+ u32 iovcr0; /* 0x110 */
+ u32 iovcr1; /* 0x114 */
+ u32 dqsdr; /* 0x118 */
+ u32 dxccr; /* 0x11c */
+ u32 odtmap; /* 0x120 */
+ u32 zqctl0; /* 0x124 */
+ u32 zqctl1; /* 0x128 */
+ u8 res6[0x14]; /* 0x12c */
+ u32 zqcr0; /* 0x140 zq control register 0 */
+ u32 zqcr1; /* 0x144 zq control register 1 */
+ u32 zqcr2; /* 0x148 zq control register 2 */
+ u32 zqsr0; /* 0x14c zq status register 0 */
+ u32 zqsr1; /* 0x150 zq status register 1 */
+ u8 res7[0x6c]; /* 0x154 */
+ u32 sched; /* 0x1c0 */
+ u32 perfhpr0; /* 0x1c4 */
+ u32 perfhpr1; /* 0x1c8 */
+ u32 perflpr0; /* 0x1cc */
+ u32 perflpr1; /* 0x1d0 */
+ u32 perfwr0; /* 0x1d4 */
+ u32 perfwr1; /* 0x1d8 */
+};
+
+#define DXnGTR(x) (SUNXI_DRAM_CTL0_BASE + 0x00000340 + 0x80 * x)
+#define DXnGCR0(x) (SUNXI_DRAM_CTL0_BASE + 0x00000344 + 0x80 * x)
+#define DXnGSR0(x) (SUNXI_DRAM_CTL0_BASE + 0x00000348 + 0x80 * x)
+#define DXnGSR1(x) (SUNXI_DRAM_CTL0_BASE + 0x0000034c + 0x80 * x)
+#define DXnGSR2(x) (SUNXI_DRAM_CTL0_BASE + 0x00000350 + 0x80 * x)
+
+/*
+ * DRAM common (sunxi_mctl_com_reg) register constants.
+ */
+#define MCTL_CR_RANK_MASK (3 << 0)
+#define MCTL_CR_RANK(x) (((x) - 1) << 0)
+#define MCTL_CR_BANK_MASK (3 << 2)
+#define MCTL_CR_BANK(x) ((x) << 2)
+#define MCTL_CR_ROW_MASK (0xf << 4)
+#define MCTL_CR_ROW(x) (((x) - 1) << 4)
+#define MCTL_CR_PAGE_SIZE_MASK (0xf << 8)
+#define MCTL_CR_PAGE_SIZE(x) ((fls(x) - 4) << 8)
+#define MCTL_CR_BUSW_MASK (7 << 12)
+#define MCTL_CR_BUSW8 (0 << 12)
+#define MCTL_CR_BUSW16 (1 << 12)
+#define MCTL_CR_SEQUENCE (1 << 15)
+#define MCTL_CR_DDR3 (3 << 16)
+#define MCTL_CR_CHANNEL_MASK (1 << 19)
+#define MCTL_CR_CHANNEL(x) (((x) - 1) << 19)
+#define MCTL_CR_UNKNOWN (0x4 << 20)
+#define MCTL_CR_CS1_CONTROL(x) ((x) << 24)
+
+/* DRAM control (sunxi_mctl_ctl_reg) register constants */
+#define MCTL_MR0 0x1c70 /* CL=11, WR=12 */
+#define MCTL_MR1 0x40
+#define MCTL_MR2 0x18 /* CWL=8 */
+#define MCTL_MR3 0x0
+
+#endif /* _SUNXI_DRAM_SUN8I_A33_H */
#define SUNXI_GPIO_PULL_DOWN 2
/* Virtual AXP0 GPIOs */
-#define SUNXI_GPIO_AXP0_VBUS_DETECT 8
-#define SUNXI_GPIO_AXP0_VBUS_ENABLE 9
+#define SUNXI_GPIO_AXP0_PREFIX "AXP0-"
+#define SUNXI_GPIO_AXP0_VBUS_DETECT 4
+#define SUNXI_GPIO_AXP0_VBUS_ENABLE 5
+#define SUNXI_GPIO_AXP0_GPIO_COUNT 6
void sunxi_gpio_set_cfgbank(struct sunxi_gpio *pio, int bank_offset, u32 val);
void sunxi_gpio_set_cfgpin(u32 pin, u32 val);
int sunxi_name_to_gpio(const char *name);
#define name_to_gpio(name) sunxi_name_to_gpio(name)
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_AXP_GPIO
+int axp_gpio_init(void);
+#else
+static inline int axp_gpio_init(void) { return 0; }
+#endif
+
#endif /* _SUNXI_GPIO_H */
u32 chda; /* 0x90 */
u32 cbda; /* 0x94 */
u32 res1[26];
-#if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I) || \
- defined(CONFIG_MACH_SUN9I)
+#ifdef CONFIG_SUNXI_GEN_SUN6I
u32 res2[64];
#endif
u32 fifo; /* 0x100 / 0x200 FIFO access address */
--- /dev/null
+/*
+ * (C) Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Sunxi PMIC bus access helpers header
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _SUNXI_PMIC_BUS_H
+#define _SUNXI_PMIS_BUS_H
+
+int pmic_bus_init(void);
+int pmic_bus_read(u8 reg, u8 *data);
+int pmic_bus_write(u8 reg, u8 data);
+int pmic_bus_setbits(u8 reg, u8 bits);
+int pmic_bus_clrbits(u8 reg, u8 bits);
+
+#endif
*/
void return_to_fel(uint32_t lr, uint32_t sp);
+/* Board / SoC level designware gmac init */
+int sunxi_gmac_initialize(bd_t *bis);
+
#endif
struct sunxi_timer timer[6]; /* We have 6 timers */
u8 res2[16];
struct sunxi_avs avs;
-#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I)
+#ifdef CONFIG_SUNXI_GEN_SUN4I
struct sunxi_wdog wdog; /* 0x90 */
/* XXX the following is not accurate for sun5i/sun7i */
struct sunxi_64cnt cnt64; /* 0xa0 */
struct sunxi_tgp tgp[4];
u8 res5[8];
u32 cpu_cfg;
-#else /* CONFIG_MACH_SUN6I || CONFIG_MACH_SUN8I || ... */
+#endif
+#ifdef CONFIG_SUNXI_GEN_SUN6I
u8 res3[16];
struct sunxi_wdog wdog[5]; /* We have 5 watchdogs */
#endif
--- /dev/null
+/*
+ * Sunxi usb-phy code
+ *
+ * Copyright (C) 2015 Hans de Goede <hdegoede@redhat.com>
+ * Copyright (C) 2014 Roman Byshko <rbyshko@gmail.com>
+ *
+ * Based on code from
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+int sunxi_usb_phy_probe(void);
+int sunxi_usb_phy_remove(void);
+void sunxi_usb_phy_init(int index);
+void sunxi_usb_phy_exit(int index);
+void sunxi_usb_phy_power_on(int index);
+void sunxi_usb_phy_power_off(int index);
+int sunxi_usb_phy_vbus_detect(int index);
+void sunxi_usb_phy_enable_squelch_detect(int index, int enable);
+++ /dev/null
-/*
- * Sunxi usb-controller code shared between the ehci and musb controllers
- *
- * Copyright (C) 2014 Roman Byshko
- *
- * Roman Byshko <rbyshko@gmail.com>
- *
- * Based on code from
- * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-extern const struct musb_platform_ops sunxi_musb_ops;
-
-void *sunxi_usbc_get_io_base(int index);
-int sunxi_usbc_request_resources(int index);
-int sunxi_usbc_free_resources(int index);
-void sunxi_usbc_enable(int index);
-void sunxi_usbc_disable(int index);
-void sunxi_usbc_vbus_enable(int index);
-void sunxi_usbc_vbus_disable(int index);
-int sunxi_usbc_vbus_detect(int index);
-void sunxi_usbc_enable_squelch_detect(int index, int enable);
if ARCH_SUNXI
+# Note only one of these may be selected at a time! But hidden choices are
+# not supported by Kconfig
+config SUNXI_GEN_SUN4I
+ bool
+ ---help---
+ Select this for sunxi SoCs which have resets and clocks set up
+ as the original A10 (mach-sun4i).
+
+config SUNXI_GEN_SUN6I
+ bool
+ ---help---
+ Select this for sunxi SoCs which have sun6i like periphery, like
+ separate ahb reset control registers, custom pmic bus, new style
+ watchdog, etc.
+
+
choice
prompt "Sunxi SoC Variant"
config MACH_SUN4I
bool "sun4i (Allwinner A10)"
select CPU_V7
+ select SUNXI_GEN_SUN4I
select SUPPORT_SPL
config MACH_SUN5I
bool "sun5i (Allwinner A13)"
select CPU_V7
+ select SUNXI_GEN_SUN4I
select SUPPORT_SPL
config MACH_SUN6I
bool "sun6i (Allwinner A31)"
select CPU_V7
+ select SUNXI_GEN_SUN6I
select SUPPORT_SPL
config MACH_SUN7I
select CPU_V7
select CPU_V7_HAS_NONSEC
select CPU_V7_HAS_VIRT
+ select SUNXI_GEN_SUN4I
select SUPPORT_SPL
select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-config MACH_SUN8I
+config MACH_SUN8I_A23
bool "sun8i (Allwinner A23)"
select CPU_V7
+ select SUNXI_GEN_SUN6I
+ select SUPPORT_SPL
+
+config MACH_SUN8I_A33
+ bool "sun8i (Allwinner A33)"
+ select CPU_V7
+ select SUNXI_GEN_SUN6I
select SUPPORT_SPL
endchoice
+# The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33"
+config MACH_SUN8I
+ bool
+ default y if MACH_SUN8I_A23 || MACH_SUN8I_A33
+
+
config DRAM_CLK
int "sunxi dram clock speed"
default 312 if MACH_SUN6I || MACH_SUN8I
at the same time, the system can be only booted in the FEL mode.
Only enable this if you really know what you are doing.
-config FDTFILE
- string "Default fdtfile env setting for this board"
-
config OLD_SUNXI_KERNEL_COMPAT
boolean "Enable workarounds for booting old kernels"
default n
See I2C0_ENABLE help text.
endif
+config AXP_GPIO
+ boolean "Enable support for gpio-s on axp PMICs"
+ default n
+ ---help---
+ Say Y here to enable support for the gpio pins of the axp PMIC ICs.
+
config VIDEO
boolean "Enable graphical uboot console on HDMI, LCD or VGA"
default y
---help---
Set the GMAC Transmit Clock Delay Chain value.
+config NET
+ default y
+
+config NETDEVICES
+ default y
+
+config DM_ETH
+ default y
+
+config DM_SERIAL
+ default y
+
endif
F: configs/Wits_Pro_A20_DKT_defconfig
F: include/configs/sun8i.h
F: configs/Ippo_q8h_v1_2_defconfig
+F: configs/Ippo_q8h_v1_2_a33_1024x600_defconfig
A20-OLINUXINO-LIME BOARD
M: FUKAUMI Naoki <naobsd@gmail.com>
S: Maintained
F: configs/Ampe_A76_defconfig
+Astar MID756 BOARD
+M: VishnuPatekar <vishnupatekar0510@gmail.com>
+S: Maintained
+F: configs/Astar_MID756_defconfig
+
COLOMBUS BOARD
M: Maxime Ripard <maxime.ripard@free-electrons.com>
S: Maintained
#include <asm/arch/dram.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
-#include <asm/arch/usbc.h>
+#include <asm/arch/usb_phy.h>
+#include <asm/gpio.h>
#include <asm/io.h>
#include <linux/usb/musb.h>
#include <net.h>
/* So that we can use pin names in Kconfig and sunxi_name_to_gpio() */
int soft_i2c_gpio_sda;
int soft_i2c_gpio_scl;
+
+static int soft_i2c_board_init(void)
+{
+ int ret;
+
+ soft_i2c_gpio_sda = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_PANEL_I2C_SDA);
+ if (soft_i2c_gpio_sda < 0) {
+ printf("Error invalid soft i2c sda pin: '%s', err %d\n",
+ CONFIG_VIDEO_LCD_PANEL_I2C_SDA, soft_i2c_gpio_sda);
+ return soft_i2c_gpio_sda;
+ }
+ ret = gpio_request(soft_i2c_gpio_sda, "soft-i2c-sda");
+ if (ret) {
+ printf("Error requesting soft i2c sda pin: '%s', err %d\n",
+ CONFIG_VIDEO_LCD_PANEL_I2C_SDA, ret);
+ return ret;
+ }
+
+ soft_i2c_gpio_scl = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_PANEL_I2C_SCL);
+ if (soft_i2c_gpio_scl < 0) {
+ printf("Error invalid soft i2c scl pin: '%s', err %d\n",
+ CONFIG_VIDEO_LCD_PANEL_I2C_SCL, soft_i2c_gpio_scl);
+ return soft_i2c_gpio_scl;
+ }
+ ret = gpio_request(soft_i2c_gpio_scl, "soft-i2c-scl");
+ if (ret) {
+ printf("Error requesting soft i2c scl pin: '%s', err %d\n",
+ CONFIG_VIDEO_LCD_PANEL_I2C_SCL, ret);
+ return ret;
+ }
+
+ return 0;
+}
+#else
+static int soft_i2c_board_init(void) { return 0; }
#endif
DECLARE_GLOBAL_DATA_PTR;
/* add board specific code here */
int board_init(void)
{
- int id_pfr1;
+ int id_pfr1, ret;
gd->bd->bi_boot_params = (PHYS_SDRAM_0 + 0x100);
asm volatile("mcr p15, 0, %0, c14, c0, 0" : : "r"(24000000));
}
- return 0;
+ ret = axp_gpio_init();
+ if (ret)
+ return ret;
+
+ /* Uses dm gpio code so do this here and not in i2c_init_board() */
+ return soft_i2c_board_init();
}
int dram_init(void)
clock_twi_onoff(4, 1);
#endif
#endif
-
-#if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
- soft_i2c_gpio_sda = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_PANEL_I2C_SDA);
- soft_i2c_gpio_scl = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_PANEL_I2C_SCL);
-#endif
}
#ifdef CONFIG_SPL_BUILD
#endif
#if defined(CONFIG_MUSB_HOST) || defined(CONFIG_MUSB_GADGET)
+extern const struct musb_platform_ops sunxi_musb_ops;
+
static struct musb_hdrc_config musb_config = {
.multipoint = 1,
.dyn_fifo = 1,
}
}
+ ret = sunxi_usb_phy_probe();
+ if (ret)
+ return ret;
+
#if defined(CONFIG_MUSB_HOST) || defined(CONFIG_MUSB_GADGET)
musb_register(&musb_plat, NULL, (void *)SUNXI_USB0_BASE);
#endif
(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
/* Set up clock gating */
-#ifndef CONFIG_MACH_SUN6I
- setbits_le32(&ccm->ahb_gate1, 0x1 << AHB_GATE_OFFSET_GMAC);
-#else
+#ifdef CONFIG_SUNXI_GEN_SUN6I
setbits_le32(&ccm->ahb_reset0_cfg, 0x1 << AHB_RESET_OFFSET_GMAC);
setbits_le32(&ccm->ahb_gate0, 0x1 << AHB_GATE_OFFSET_GMAC);
+#else
+ setbits_le32(&ccm->ahb_gate1, 0x1 << AHB_GATE_OFFSET_GMAC);
#endif
/* Set MII clock */
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,AHCI,SATAPWR=SUNXI_GPC(3),USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-olinuxino-lime.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-olinuxino-lime"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN4I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP152_POWER,SUNXI_EMAC,USB_EHCI"
-CONFIG_FDTFILE="sun5i-a10s-olinuxino-micro.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-olinuxino-micro"
CONFIG_MMC_SUNXI_SLOT_EXTRA=1
CONFIG_USB1_VBUS_PIN="PB10"
CONFIG_MMC0_CD_PIN="PG1"
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2,USB_EHCI"
-CONFIG_FDTFILE="sun5i-a13-olinuxino-micro.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-olinuxino-micro"
CONFIG_USB1_VBUS_PIN="PG11"
CONFIG_VIDEO_HDMI=n
CONFIG_VIDEO_VGA_VIA_LCD=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2,AXP209_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun5i-a13-olinuxino.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-olinuxino"
CONFIG_USB1_VBUS_PIN="PG11"
CONFIG_VIDEO_HDMI=n
CONFIG_VIDEO_VGA_VIA_LCD=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPC(3),USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-olinuxino-lime2.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-lime2"
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_USB0_VBUS_PIN="PC17"
CONFIG_USB0_VBUS_DET="PH5"
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPC(3),USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-olinuxino-lime.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-lime"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN7I=y
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPB(8),USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-olinuxino-micro.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-micro"
CONFIG_MMC_SUNXI_SLOT_EXTRA=3
CONFIG_VIDEO_VGA=y
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
# Also see: http://linux-sunxi.org/Ainol_AW1
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun7i-a20-ainol-aw1.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-ainol-aw1"
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB9"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:40000,le:87,ri:112,up:38,lo:141,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_POWER="PH8"
CONFIG_VIDEO_LCD_BL_EN="PH7"
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2,AXP209_POWER"
-CONFIG_FDTFILE="sun5i-a13-ampe-a76.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-ampe-a76"
CONFIG_MMC0_CD_PIN="PG0"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PG12"
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
--- /dev/null
+# The Astar MID756 is a 7" tablet using the A33 SoC with a 800x480 LCD screen,
+# 512M RAM, 8G ROM and integrated sdio wifi.
+#
+# Also see: http://linux-sunxi.org/Softwinner_astar-rda
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-astar-mid756"
+CONFIG_USB_MUSB_SUNXI=y
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:168,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_POWER="PH7"
+CONFIG_VIDEO_LCD_BL_EN="PH6"
+CONFIG_VIDEO_LCD_BL_PWM="PH0"
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A33=y
+CONFIG_DRAM_CLK=480
+# zq = 0x3bbb
+CONFIG_DRAM_ZQ=15291
+# Wifi power
+CONFIG_AXP221_DLDO1_VOLT=3300
+# aldo1 is connected to VCC-IO, VCC-PD, VCC-USB and VCC-HP
+CONFIG_AXP221_ALDO1_VOLT=3000
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP152_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun5i-a10s-auxtek-t004.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-auxtek-t004"
CONFIG_USB1_VBUS_PIN="PG13"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-bananapi.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi"
CONFIG_GMAC_TX_DELAY=3
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-bananapro.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapro"
CONFIG_USB1_VBUS_PIN="PH0"
CONFIG_USB2_VBUS_PIN="PH1"
CONFIG_GMAC_TX_DELAY=3
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC"
-CONFIG_FDTFILE="sun6i-a31s-cs908.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-cs908"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN6I=y
CONFIG_USB1_VBUS_PIN=""
CONFIG_USB2_VBUS_PIN=""
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun4i-a10-chuwi-v7-cw0825.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-chuwi-v7-cw0825"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB9"
CONFIG_USB0_VBUS_DET="PH5"
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC"
-CONFIG_FDTFILE="sun6i-a31-colombus.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-colombus"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN6I=y
# No Vbus gpio for usb1
CONFIG_USB1_VBUS_PIN=""
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPB(8),USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-cubieboard2.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-cubieboard2"
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,AHCI,SATAPWR=SUNXI_GPB(8),USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-cubieboard.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-cubieboard"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN4I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPH(12),USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-cubietruck.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-cubietruck"
CONFIG_GMAC_TX_DELAY=1
CONFIG_VIDEO_VGA=y
CONFIG_ARM=y
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPA(21)"
-CONFIG_FDTFILE="sun6i-a31-hummingbird.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-hummingbird"
CONFIG_VIDEO_VGA_VIA_LCD=y
CONFIG_VIDEO_VGA_EXTERNAL_DAC_EN="PH25"
CONFIG_ARM=y
# No Vbus gpio for usb2
CONFIG_USB2_VBUS_PIN=""
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
# headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun4i-a10-hyundai-a7hd.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-hyundai-a7hd"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB09"
CONFIG_USB0_VBUS_DET="PH5"
--- /dev/null
+# This is a defconfig for generic 7" tablets using the Ippo q8h v1.2 pcb,
+# with an A33 SoC (the pcb can take an A23 or an A33), and a 1024x600 LCD
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a33-ippo-q8h-v1.2-lcd1024x600"
+CONFIG_USB_MUSB_SUNXI=y
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_POWER="PH7"
+CONFIG_VIDEO_LCD_BL_EN="PH6"
+CONFIG_VIDEO_LCD_BL_PWM="PH0"
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A33=y
+CONFIG_DRAM_CLK=480
+# zq = 0x3bbb
+CONFIG_DRAM_ZQ=15291
+# Wifi power
+CONFIG_AXP221_DLDO1_VOLT=3300
+# aldo1 is connected to VCC-IO, VCC-PD, VCC-USB and VCC-HP
+CONFIG_AXP221_ALDO1_VOLT=3000
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
-CONFIG_FDTFILE="sun8i-a23-ippo-q8h-v1.2.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-ippo-q8h-v1.2"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:167,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
-CONFIG_MACH_SUN8I=y
+CONFIG_MACH_SUN8I_A23=y
CONFIG_DRAM_CLK=432
# zq = 0xf74a
CONFIG_DRAM_ZQ=63306
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
-CONFIG_FDTFILE="sun8i-a23-ippo-q8h-v5.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-ippo-q8h-v5"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:168,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
-CONFIG_MACH_SUN8I=y
+CONFIG_MACH_SUN8I_A23=y
CONFIG_DRAM_CLK=480
# zq = 0xf777
CONFIG_DRAM_ZQ=63351
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPH(2),USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-pcduino3-nano.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-pcduino3-nano"
CONFIG_GMAC_TX_DELAY=3
CONFIG_USB1_VBUS_PIN="PH11"
CONFIG_ARM=y
CONFIG_DRAM_ZQ=122
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,AHCI,SATAPWR=SUNXI_GPH(2),USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-pcduino3.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-pcduino3"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN7I=y
CONFIG_DRAM_CLK=480
CONFIG_DRAM_ZQ=122
CONFIG_DRAM_EMR1=4
-CONFIG_DM=y
-CONFIG_DM_GPIO=y
-CONFIG_DM_SERIAL=y
-CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-pcduino3"
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_DISABLE_OF_CONTROL=y
-CONFIG_OF_SEPARATE=y
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
-CONFIG_DM_ETH=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-pcduino.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-pcduino"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN4I=y
# 1 USB A, 1 USB mini OTG, Bluetooth and Wireless LAN.
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-mk808c.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-mk808c"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN7I=y
# http://linux-sunxi.org/MSI_Primo73
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun7i-a20-primo73.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-primo73"
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:60000,le:60,ri:160,up:13,lo:12,hs:100,vs:10,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH8"
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS=""
-CONFIG_FDTFILE="sun6i-a31s-primo81.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-primo81"
CONFIG_VIDEO_LCD_MODE="x:768,y:1024,depth:18,pclk_khz:66000,le:56,ri:60,up:30,lo:36,hs:64,vs:50,sync:3,vmode:0"
CONFIG_VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828=y
CONFIG_VIDEO_LCD_SSD2828_TX_CLK=27
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_EMAC,AHCI,USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-marsboard.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-marsboard"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN4I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,MACPWR=SUNXI_GPH(15),AHCI,USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-a1000.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-a1000"
CONFIG_VIDEO_VGA=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
# For more details see: http://linux-sunxi.org/Mele_I7
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC"
-CONFIG_FDTFILE="sun6i-a31-i7.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-i7"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN6I=y
# No Vbus gpio for usb2
CONFIG_USB2_VBUS_PIN=""
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-m3.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-m3"
CONFIG_VIDEO_VGA=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="SUNXI_GMAC,AHCI,USB_EHCI,STATUSLED=234"
-CONFIG_FDTFILE="sun7i-a20-m5.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-m5"
CONFIG_VIDEO_HDMI=y
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_USB1_VBUS_PIN="PH6"
CONFIG_DRAM_ZQ=122
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC"
-CONFIG_FDTFILE="sun6i-a31-m9.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-m9"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN6I=y
# No Vbus gpio for usb2
CONFIG_USB2_VBUS_PIN=""
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-mini-xplus.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-mini-xplus"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN4I=y
# http://www.orangepi.org/
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-orangepi.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-orangepi"
CONFIG_GMAC_TX_DELAY=3
CONFIG_USB1_VBUS_PIN="PH26"
CONFIG_USB2_VBUS_PIN="PH22"
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
# http://www.orangepi.org/
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-orangepi-mini.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-orangepi-mini"
CONFIG_MMC_SUNXI_SLOT_EXTRA=3
CONFIG_MMC0_CD_PIN="PH10"
CONFIG_MMC3_CD_PIN="PH11"
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2,AXP209_POWER"
-CONFIG_FDTFILE="sun5i-a13-tzx-q8-713b7.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-tzx-q8-713b7"
CONFIG_MMC0_CD_PIN="PG0"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PG12"
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun5i-a13-utoo-p66.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-utoo-p66"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB04"
CONFIG_USB0_VBUS_DET="PG01"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
CONFIG_VIDEO_LCD_TL059WV5C0=y
+CONFIG_AXP_GPIO=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_MMC0_CD_PIN="PG0"
CONFIG_ARM=y
CONFIG_DRAM_CLK=432
CONFIG_DRAM_ZQ=123
CONFIG_DRAM_EMR1=0
+CONFIG_DM_SERIAL=n
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-wexler-tab7200.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-wexler-tab7200"
CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:24,pclk_khz:33000,le:45,ri:210,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_POWER="PH8"
CONFIG_VIDEO_LCD_BL_EN="PH7"
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,AHCI,USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-wits-pro-a20-dkt.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-wits-pro-a20-dkt"
CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:24,pclk_khz:65000,le:159,ri:160,up:22,lo:15,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_POWER="PH8"
CONFIG_VIDEO_LCD_BL_EN="PH7"
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
# Also see: http://linux-sunxi.org/Yones_Toptech_BD1078
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun7i-a20-yones-toptech-bd1078.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-yones-toptech-bd1078"
CONFIG_MMC_SUNXI_SLOT_EXTRA=1
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_MMC1_CD_PIN="PH2"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB9"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:63000,le:32,ri:287,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_PANEL_LVDS=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-ba10-tvbox.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-ba10-tvbox"
CONFIG_USB2_VBUS_PIN="PH12"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun5i-a13-forfun-q88db.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-forfun-q88db"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PG12"
CONFIG_USB0_VBUS_DET="PG1"
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,MACPWR=SUNXI_GPH(21),USB_EHCI"
-CONFIG_FDTFILE="sun7i-a20-i12-tvbox.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-i12-tvbox"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN7I=y
CONFIG_DRAM_ZQ=127
CONFIG_DRAM_EMR1=4
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
# Also see: http://linux-sunxi.org/INet_3F
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun4i-a10-inet-3f.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-inet-3f"
CONFIG_MMC0_CD_PIN="PH1"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB9"
# Also see: http://linux-sunxi.org/INet_3W
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun4i-a10-inet-3w.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-inet-3w"
CONFIG_MMC0_CD_PIN="PH20"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PB9"
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER"
-CONFIG_FDTFILE="sun5i-a13-inet-86vs.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-inet-86vs"
CONFIG_USB_MUSB_SUNXI=y
CONFIG_USB0_VBUS_PIN="PG12"
CONFIG_USB0_VBUS_DET="PG1"
CONFIG_VIDEO_LCD_POWER="AXP0-0"
CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_AXP_GPIO=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN5I=y
# For more details see: http://linux-sunxi.org/Jesurun_Q5
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_EMAC,USB_EHCI,MACPWR=SUNXI_GPH(19)"
-CONFIG_FDTFILE="sun4i-a10-jesurun-q5.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-jesurun-q5"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN4I=y
# Also see http://focalcrest.com/en/pc.html#pro02
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPA(21)"
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-mixtile-loftq"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN6I=y
# No Vbus gpio for usb2
CONFIG_USB2_VBUS_PIN=""
CONFIG_ETH_DESIGNWARE=y
-CONFIG_NETDEVICES=y
-CONFIG_NET=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP152_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun5i-a10s-mk802.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-mk802"
CONFIG_USB1_VBUS_PIN="PB10"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-mk802.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-mk802"
CONFIG_USB2_VBUS_PIN="PH12"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun4i-a10-mk802ii.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-mk802ii"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN4I=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP152_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun5i-a10s-r7-tv-dongle.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a10s-r7-tv-dongle"
CONFIG_USB1_VBUS_PIN="PG13"
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
# More details are available at: http://linux-sunxi.org/Gemei_G9
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,USB_EHCI"
-CONFIG_FDTFILE="sun4i-gemei-g9.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-gemei-g9"
CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:100000,le:799,ri:260,up:15,lo:16,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_PANEL_LVDS=y
CONFIG_VIDEO_LCD_POWER="PH8"
ifndef CONFIG_SPL_BUILD
obj-$(CONFIG_DM_GPIO) += gpio-uclass.o
+obj-$(CONFIG_AXP_GPIO) += axp_gpio.o
endif
/* TODO(sjg@chromium.org): Only tegra supports driver model in SPL */
ifdef CONFIG_TEGRA_GPIO
--- /dev/null
+/*
+ * (C) Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * X-Powers AXP Power Management ICs gpio driver
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/pmic_bus.h>
+#include <asm/gpio.h>
+#include <dm.h>
+#include <dm/device-internal.h>
+#include <dm/lists.h>
+#include <dm/root.h>
+#include <errno.h>
+
+#ifdef CONFIG_AXP152_POWER
+#include <axp152.h>
+#elif defined CONFIG_AXP209_POWER
+#include <axp209.h>
+#elif defined CONFIG_AXP221_POWER
+#include <axp221.h>
+#else
+#error Unknown AXP model
+#endif
+
+static int axp_gpio_set_value(struct udevice *dev, unsigned pin, int val);
+
+static u8 axp_get_gpio_ctrl_reg(unsigned pin)
+{
+ switch (pin) {
+ case 0: return AXP_GPIO0_CTRL;
+ case 1: return AXP_GPIO1_CTRL;
+#ifdef AXP_GPIO2_CTRL
+ case 2: return AXP_GPIO2_CTRL;
+#endif
+#ifdef AXP_GPIO3_CTRL
+ case 3: return AXP_GPIO3_CTRL;
+#endif
+ }
+ return 0;
+}
+
+static int axp_gpio_direction_input(struct udevice *dev, unsigned pin)
+{
+ u8 reg;
+
+ switch (pin) {
+#ifndef CONFIG_AXP152_POWER /* NA on axp152 */
+ case SUNXI_GPIO_AXP0_VBUS_DETECT:
+ return 0;
+#endif
+ default:
+ reg = axp_get_gpio_ctrl_reg(pin);
+ if (reg == 0)
+ return -EINVAL;
+
+ return pmic_bus_write(reg, AXP_GPIO_CTRL_INPUT);
+ }
+}
+
+static int axp_gpio_direction_output(struct udevice *dev, unsigned pin,
+ int val)
+{
+ __maybe_unused int ret;
+ u8 reg;
+
+ switch (pin) {
+#ifdef CONFIG_AXP221_POWER /* Only available on axp221/axp223 */
+ case SUNXI_GPIO_AXP0_VBUS_ENABLE:
+ ret = pmic_bus_clrbits(AXP221_MISC_CTRL,
+ AXP221_MISC_CTRL_N_VBUSEN_FUNC);
+ if (ret)
+ return ret;
+
+ return axp_gpio_set_value(dev, pin, val);
+#endif
+ default:
+ reg = axp_get_gpio_ctrl_reg(pin);
+ if (reg == 0)
+ return -EINVAL;
+
+ return pmic_bus_write(reg, val ? AXP_GPIO_CTRL_OUTPUT_HIGH :
+ AXP_GPIO_CTRL_OUTPUT_LOW);
+ }
+}
+
+static int axp_gpio_get_value(struct udevice *dev, unsigned pin)
+{
+ u8 reg, val, mask;
+ int ret;
+
+ switch (pin) {
+#ifndef CONFIG_AXP152_POWER /* NA on axp152 */
+ case SUNXI_GPIO_AXP0_VBUS_DETECT:
+ ret = pmic_bus_read(AXP_POWER_STATUS, &val);
+ mask = AXP_POWER_STATUS_VBUS_PRESENT;
+ break;
+#endif
+#ifdef CONFIG_AXP221_POWER /* Only available on axp221/axp223 */
+ case SUNXI_GPIO_AXP0_VBUS_ENABLE:
+ ret = pmic_bus_read(AXP221_VBUS_IPSOUT, &val);
+ mask = AXP221_VBUS_IPSOUT_DRIVEBUS;
+ break;
+#endif
+ default:
+ reg = axp_get_gpio_ctrl_reg(pin);
+ if (reg == 0)
+ return -EINVAL;
+
+ ret = pmic_bus_read(AXP_GPIO_STATE, &val);
+ mask = 1 << (pin + AXP_GPIO_STATE_OFFSET);
+ }
+ if (ret)
+ return ret;
+
+ return (val & mask) ? 1 : 0;
+}
+
+static int axp_gpio_set_value(struct udevice *dev, unsigned pin, int val)
+{
+ u8 reg;
+
+ switch (pin) {
+#ifdef CONFIG_AXP221_POWER /* Only available on axp221/axp223 */
+ case SUNXI_GPIO_AXP0_VBUS_ENABLE:
+ if (val)
+ return pmic_bus_setbits(AXP221_VBUS_IPSOUT,
+ AXP221_VBUS_IPSOUT_DRIVEBUS);
+ else
+ return pmic_bus_clrbits(AXP221_VBUS_IPSOUT,
+ AXP221_VBUS_IPSOUT_DRIVEBUS);
+#endif
+ default:
+ reg = axp_get_gpio_ctrl_reg(pin);
+ if (reg == 0)
+ return -EINVAL;
+
+ return pmic_bus_write(reg, val ? AXP_GPIO_CTRL_OUTPUT_HIGH :
+ AXP_GPIO_CTRL_OUTPUT_LOW);
+ }
+}
+
+static const struct dm_gpio_ops gpio_axp_ops = {
+ .direction_input = axp_gpio_direction_input,
+ .direction_output = axp_gpio_direction_output,
+ .get_value = axp_gpio_get_value,
+ .set_value = axp_gpio_set_value,
+};
+
+static int gpio_axp_probe(struct udevice *dev)
+{
+ struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+
+ /* Tell the uclass how many GPIOs we have */
+ uc_priv->bank_name = strdup(SUNXI_GPIO_AXP0_PREFIX);
+ uc_priv->gpio_count = SUNXI_GPIO_AXP0_GPIO_COUNT;
+
+ return 0;
+}
+
+U_BOOT_DRIVER(gpio_axp) = {
+ .name = "gpio_axp",
+ .id = UCLASS_GPIO,
+ .ops = &gpio_axp_ops,
+ .probe = gpio_axp_probe,
+};
+
+int axp_gpio_init(void)
+{
+ struct udevice *dev;
+ int ret;
+
+ ret = pmic_bus_init();
+ if (ret)
+ return ret;
+
+ /* There is no devicetree support for the axp yet, so bind directly */
+ ret = device_bind_driver(dm_root(), "gpio_axp", "AXP-gpio", &dev);
+ if (ret)
+ return ret;
+
+ return 0;
+}
#include <errno.h>
#include <fdtdec.h>
#include <malloc.h>
+#include <asm/arch/gpio.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <dm/device-internal.h>
-#ifdef CONFIG_AXP209_POWER
-#include <axp209.h>
-#endif
-#ifdef CONFIG_AXP221_POWER
-#include <axp221.h>
-#endif
DECLARE_GLOBAL_DATA_PTR;
int gpio_direction_input(unsigned gpio)
{
-#ifdef AXP_GPIO
- if (gpio >= SUNXI_GPIO_AXP0_START)
- return axp_gpio_direction_input(gpio - SUNXI_GPIO_AXP0_START);
-#endif
sunxi_gpio_set_cfgpin(gpio, SUNXI_GPIO_INPUT);
return 0;
int gpio_direction_output(unsigned gpio, int value)
{
-#ifdef AXP_GPIO
- if (gpio >= SUNXI_GPIO_AXP0_START)
- return axp_gpio_direction_output(gpio - SUNXI_GPIO_AXP0_START,
- value);
-#endif
sunxi_gpio_set_cfgpin(gpio, SUNXI_GPIO_OUTPUT);
return sunxi_gpio_output(gpio, value);
int gpio_get_value(unsigned gpio)
{
-#ifdef AXP_GPIO
- if (gpio >= SUNXI_GPIO_AXP0_START)
- return axp_gpio_get_value(gpio - SUNXI_GPIO_AXP0_START);
-#endif
return sunxi_gpio_input(gpio);
}
int gpio_set_value(unsigned gpio, int value)
{
-#ifdef AXP_GPIO
- if (gpio >= SUNXI_GPIO_AXP0_START)
- return axp_gpio_set_value(gpio - SUNXI_GPIO_AXP0_START, value);
-#endif
return sunxi_gpio_output(gpio, value);
}
-int sunxi_name_to_gpio_bank(const char *name)
-{
- int group = 0;
-
- if (*name == 'P' || *name == 'p')
- name++;
- if (*name >= 'A') {
- group = *name - (*name > 'a' ? 'a' : 'A');
- return group;
- }
-
- return -1;
-}
-
int sunxi_name_to_gpio(const char *name)
{
int group = 0;
long pin;
char *eptr;
-#ifdef AXP_GPIO
- if (strncasecmp(name, "AXP0-", 5) == 0) {
- name += 5;
- if (strcmp(name, "VBUS-DETECT") == 0)
- return SUNXI_GPIO_AXP0_START +
- SUNXI_GPIO_AXP0_VBUS_DETECT;
- if (strcmp(name, "VBUS-ENABLE") == 0)
- return SUNXI_GPIO_AXP0_START +
- SUNXI_GPIO_AXP0_VBUS_ENABLE;
- pin = simple_strtol(name, &eptr, 10);
- if (!*name || *eptr)
- return -1;
- return SUNXI_GPIO_AXP0_START + pin;
- }
-#endif
if (*name == 'P' || *name == 'p')
name++;
if (*name >= 'A') {
}
#endif
+int sunxi_name_to_gpio_bank(const char *name)
+{
+ int group = 0;
+
+ if (*name == 'P' || *name == 'p')
+ name++;
+ if (*name >= 'A') {
+ group = *name - (*name > 'a' ? 'a' : 'A');
+ return group;
+ }
+
+ return -1;
+}
+
#ifdef CONFIG_DM_GPIO
+/* TODO(sjg@chromium.org): Remove this function and use device tree */
+int sunxi_name_to_gpio(const char *name)
+{
+ unsigned int gpio;
+ int ret;
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_AXP_GPIO
+ char lookup[8];
+
+ if (strcasecmp(name, "AXP0-VBUS-DETECT") == 0) {
+ sprintf(lookup, SUNXI_GPIO_AXP0_PREFIX "%d",
+ SUNXI_GPIO_AXP0_VBUS_DETECT);
+ name = lookup;
+ } else if (strcasecmp(name, "AXP0-VBUS-ENABLE") == 0) {
+ sprintf(lookup, SUNXI_GPIO_AXP0_PREFIX "%d",
+ SUNXI_GPIO_AXP0_VBUS_ENABLE);
+ name = lookup;
+ }
+#endif
+ ret = gpio_lookup_name(name, NULL, NULL, &gpio);
+
+ return ret ? ret : gpio;
+}
+
static int sunxi_gpio_direction_input(struct udevice *dev, unsigned offset)
{
struct sunxi_gpio_platdata *plat = dev_get_platdata(dev);
{
char *name;
- name = malloc(2);
+ name = malloc(3);
if (name) {
- name[0] = 'A' + bank;
- name[1] = '\0';
+ name[0] = 'P';
+ name[1] = 'A' + bank;
+ name[2] = '\0';
}
return name;
}
static const struct udevice_id sunxi_gpio_ids[] = {
+ { .compatible = "allwinner,sun4i-a10-pinctrl" },
+ { .compatible = "allwinner,sun5i-a10s-pinctrl" },
+ { .compatible = "allwinner,sun5i-a13-pinctrl" },
+ { .compatible = "allwinner,sun6i-a31-pinctrl" },
+ { .compatible = "allwinner,sun6i-a31s-pinctrl" },
{ .compatible = "allwinner,sun7i-a20-pinctrl" },
+ { .compatible = "allwinner,sun8i-a23-pinctrl" },
+ { .compatible = "allwinner,sun9i-a80-pinctrl" },
{ }
};
*/
#include <common.h>
+#include <errno.h>
#include <malloc.h>
#include <mmc.h>
#include <asm/io.h>
case 2: return sunxi_name_to_gpio(CONFIG_MMC2_CD_PIN);
case 3: return sunxi_name_to_gpio(CONFIG_MMC3_CD_PIN);
}
- return -1;
+ return -EINVAL;
}
static int mmc_resource_init(int sdc_no)
mmchost->mmc_no = sdc_no;
cd_pin = sunxi_mmc_getcd_gpio(sdc_no);
- if (cd_pin != -1) {
+ if (cd_pin >= 0) {
ret = gpio_request(cd_pin, "mmc_cd");
if (!ret)
ret = gpio_direction_input(cd_pin);
/* config ahb clock */
setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MMC(sdc_no));
-#if defined(CONFIG_MACH_SUN6I) || defined(CONFIG_MACH_SUN8I) || \
- defined(CONFIG_MACH_SUN9I)
+#ifdef CONFIG_SUNXI_GEN_SUN6I
/* unassert reset */
setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MMC(sdc_no));
#endif
int cd_pin;
cd_pin = sunxi_mmc_getcd_gpio(mmchost->mmc_no);
- if (cd_pin == -1)
+ if (cd_pin < 0)
return 1;
return !gpio_get_value(cd_pin);
*/
#include <common.h>
+#include <dm.h>
#include <linux/err.h>
#include <malloc.h>
#include <miiphy.h>
#define EMAC_CRCERR (0x1 << 4)
#define EMAC_LENERR (0x3 << 5)
-#define DMA_CPU_TRRESHOLD 2000
+#define EMAC_RX_BUFSIZE 2000
struct emac_eth_dev {
- u32 speed;
- u32 duplex;
- u32 phy_configured;
+ struct emac_regs *regs;
+ struct mii_dev *bus;
+ struct phy_device *phydev;
int link_printed;
+#ifdef CONFIG_DM_ETH
+ uchar rx_buf[EMAC_RX_BUFSIZE];
+#endif
};
struct emac_rxhdr {
}
/* Read a word from phyxcer */
-static int emac_phy_read(const char *devname, unsigned char addr,
- unsigned char reg, unsigned short *value)
+static int emac_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
{
- struct eth_device *dev = eth_get_dev_by_name(devname);
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ struct emac_eth_dev *priv = bus->priv;
+ struct emac_regs *regs = priv->regs;
/* issue the phy address and reg */
writel(addr << 8 | reg, ®s->mac_madr);
/* push down the phy io line */
writel(0x0, ®s->mac_mcmd);
- /* and write data */
- *value = readl(®s->mac_mrdd);
-
- return 0;
+ /* And read data */
+ return readl(®s->mac_mrdd);
}
/* Write a word to phyxcer */
-static int emac_phy_write(const char *devname, unsigned char addr,
- unsigned char reg, unsigned short value)
+static int emac_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
+ u16 value)
{
- struct eth_device *dev = eth_get_dev_by_name(devname);
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ struct emac_eth_dev *priv = bus->priv;
+ struct emac_regs *regs = priv->regs;
/* issue the phy address and reg */
writel(addr << 8 | reg, ®s->mac_madr);
return 0;
}
-static void emac_setup(struct eth_device *dev)
+static int sunxi_emac_init_phy(struct emac_eth_dev *priv, void *dev)
+{
+ int ret, mask = 0xffffffff;
+
+#ifdef CONFIG_PHY_ADDR
+ mask = 1 << CONFIG_PHY_ADDR;
+#endif
+
+ priv->bus = mdio_alloc();
+ if (!priv->bus) {
+ printf("Failed to allocate MDIO bus\n");
+ return -ENOMEM;
+ }
+
+ priv->bus->read = emac_mdio_read;
+ priv->bus->write = emac_mdio_write;
+ priv->bus->priv = priv;
+ strcpy(priv->bus->name, "emac");
+
+ ret = mdio_register(priv->bus);
+ if (ret)
+ return ret;
+
+ priv->phydev = phy_find_by_mask(priv->bus, mask,
+ PHY_INTERFACE_MODE_MII);
+ if (!priv->phydev)
+ return -ENODEV;
+
+ phy_connect_dev(priv->phydev, dev);
+ phy_config(priv->phydev);
+
+ return 0;
+}
+
+static void emac_setup(struct emac_eth_dev *priv)
{
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ struct emac_regs *regs = priv->regs;
u32 reg_val;
- u16 phy_val;
- u32 duplex_flag;
/* Set up TX */
writel(EMAC_TX_SETUP, ®s->tx_mode);
writel(EMAC_MAC_CTL0_SETUP, ®s->mac_ctl0);
/* Set MAC CTL1 */
- emac_phy_read(dev->name, 1, 0, &phy_val);
- debug("PHY SETUP, reg 0 value: %x\n", phy_val);
- duplex_flag = !!(phy_val & (1 << 8));
-
reg_val = 0;
- if (duplex_flag)
+ if (priv->phydev->duplex == DUPLEX_FULL)
reg_val = (0x1 << 0);
writel(EMAC_MAC_CTL1_SETUP | reg_val, ®s->mac_ctl1);
writel(EMAC_MAC_MFL, ®s->mac_maxf);
}
-static void emac_reset(struct eth_device *dev)
+static void emac_reset(struct emac_eth_dev *priv)
{
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ struct emac_regs *regs = priv->regs;
debug("resetting device\n");
udelay(200);
}
-static int sunxi_emac_eth_init(struct eth_device *dev, bd_t *bd)
+static int _sunxi_emac_eth_init(struct emac_eth_dev *priv, u8 *enetaddr)
{
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
- struct emac_eth_dev *priv = dev->priv;
- u16 phy_reg;
+ struct emac_regs *regs = priv->regs;
+ int ret;
/* Init EMAC */
udelay(1);
/* Set up EMAC */
- emac_setup(dev);
+ emac_setup(priv);
- writel(dev->enetaddr[0] << 16 | dev->enetaddr[1] << 8 |
- dev->enetaddr[2], ®s->mac_a1);
- writel(dev->enetaddr[3] << 16 | dev->enetaddr[4] << 8 |
- dev->enetaddr[5], ®s->mac_a0);
+ writel(enetaddr[0] << 16 | enetaddr[1] << 8 | enetaddr[2],
+ ®s->mac_a1);
+ writel(enetaddr[3] << 16 | enetaddr[4] << 8 | enetaddr[5],
+ ®s->mac_a0);
mdelay(1);
- emac_reset(dev);
+ emac_reset(priv);
/* PHY POWER UP */
- emac_phy_read(dev->name, 1, 0, &phy_reg);
- emac_phy_write(dev->name, 1, 0, phy_reg & (~(0x1 << 11)));
- mdelay(1);
-
- emac_phy_read(dev->name, 1, 0, &phy_reg);
-
- priv->speed = miiphy_speed(dev->name, 0);
- priv->duplex = miiphy_duplex(dev->name, 0);
+ ret = phy_startup(priv->phydev);
+ if (ret) {
+ printf("Could not initialize PHY %s\n",
+ priv->phydev->dev->name);
+ return ret;
+ }
/* Print link status only once */
if (!priv->link_printed) {
printf("ENET Speed is %d Mbps - %s duplex connection\n",
- priv->speed, (priv->duplex == HALF) ? "HALF" : "FULL");
+ priv->phydev->speed,
+ priv->phydev->duplex ? "FULL" : "HALF");
priv->link_printed = 1;
}
/* Set EMAC SPEED depend on PHY */
- clrsetbits_le32(®s->mac_supp, 1 << 8,
- ((phy_reg & (0x1 << 13)) >> 13) << 8);
+ if (priv->phydev->speed == SPEED_100)
+ setbits_le32(®s->mac_supp, 1 << 8);
+ else
+ clrbits_le32(®s->mac_supp, 1 << 8);
/* Set duplex depend on phy */
- clrsetbits_le32(®s->mac_ctl1, 1 << 0,
- ((phy_reg & (0x1 << 8)) >> 8) << 0);
+ if (priv->phydev->duplex == DUPLEX_FULL)
+ setbits_le32(®s->mac_ctl1, 1 << 0);
+ else
+ clrbits_le32(®s->mac_ctl1, 1 << 0);
/* Enable RX/TX */
setbits_le32(®s->ctl, 0x7);
return 0;
}
-static void sunxi_emac_eth_halt(struct eth_device *dev)
-{
- /* Nothing to do here */
-}
-
-static int sunxi_emac_eth_recv(struct eth_device *dev)
+static int _sunxi_emac_eth_recv(struct emac_eth_dev *priv, void *packet)
{
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ struct emac_regs *regs = priv->regs;
struct emac_rxhdr rxhdr;
u32 rxcount;
u32 reg_val;
/* Had one stuck? */
rxcount = readl(®s->rx_fbc);
if (!rxcount)
- return 0;
+ return -EAGAIN;
}
reg_val = readl(®s->rx_io_data);
/* Enable RX */
setbits_le32(®s->ctl, 0x1 << 2);
- return 0;
+ return -EAGAIN;
}
/* A packet ready now
/* Move data from EMAC */
if (good_packet) {
- if (rx_len > DMA_CPU_TRRESHOLD) {
+ if (rx_len > EMAC_RX_BUFSIZE) {
printf("Received packet is too big (len=%d)\n", rx_len);
- } else {
- emac_inblk_32bit((void *)®s->rx_io_data,
- net_rx_packets[0], rx_len);
-
- /* Pass to upper layer */
- net_process_received_packet(net_rx_packets[0], rx_len);
- return rx_len;
+ return -EMSGSIZE;
}
+ emac_inblk_32bit((void *)®s->rx_io_data, packet, rx_len);
+ return rx_len;
}
- return 0;
+ return -EIO; /* Bad packet */
}
-static int sunxi_emac_eth_send(struct eth_device *dev, void *packet, int len)
+static int _sunxi_emac_eth_send(struct emac_eth_dev *priv, void *packet,
+ int len)
{
- struct emac_regs *regs = (struct emac_regs *)dev->iobase;
+ struct emac_regs *regs = priv->regs;
/* Select channel 0 */
writel(0, ®s->tx_ins);
return 0;
}
-int sunxi_emac_initialize(void)
+static void sunxi_emac_board_setup(struct emac_eth_dev *priv)
{
struct sunxi_ccm_reg *const ccm =
(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
struct sunxi_sramc_regs *sram =
(struct sunxi_sramc_regs *)SUNXI_SRAMC_BASE;
- struct emac_regs *regs =
- (struct emac_regs *)SUNXI_EMAC_BASE;
- struct eth_device *dev;
- struct emac_eth_dev *priv;
+ struct emac_regs *regs = priv->regs;
int pin;
- dev = malloc(sizeof(*dev));
- if (dev == NULL)
- return -ENOMEM;
-
- priv = (struct emac_eth_dev *)malloc(sizeof(struct emac_eth_dev));
- if (!priv) {
- free(dev);
- return -ENOMEM;
- }
-
- memset(dev, 0, sizeof(*dev));
- memset(priv, 0, sizeof(struct emac_eth_dev));
-
/* Map SRAM to EMAC */
setbits_le32(&sram->ctrl1, 0x5 << 2);
/* Set MII clock */
clrsetbits_le32(®s->mac_mcfg, 0xf << 2, 0xd << 2);
+}
+
+static int sunxi_emac_eth_start(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_platdata(dev);
+
+ return _sunxi_emac_eth_init(dev->priv, pdata->enetaddr);
+}
+
+static int sunxi_emac_eth_send(struct udevice *dev, void *packet, int length)
+{
+ struct emac_eth_dev *priv = dev_get_priv(dev);
- dev->iobase = (int)regs;
- dev->priv = priv;
- dev->init = sunxi_emac_eth_init;
- dev->halt = sunxi_emac_eth_halt;
- dev->send = sunxi_emac_eth_send;
- dev->recv = sunxi_emac_eth_recv;
- strcpy(dev->name, "emac");
+ return _sunxi_emac_eth_send(priv, packet, length);
+}
+
+static int sunxi_emac_eth_recv(struct udevice *dev, uchar **packetp)
+{
+ struct emac_eth_dev *priv = dev_get_priv(dev);
+ int rx_len;
- eth_register(dev);
+ rx_len = _sunxi_emac_eth_recv(priv, priv->rx_buf);
+ *packetp = priv->rx_buf;
- miiphy_register(dev->name, emac_phy_read, emac_phy_write);
+ return rx_len;
+}
+
+static void sunxi_emac_eth_stop(struct udevice *dev)
+{
+ /* Nothing to do here */
+}
+
+static int sunxi_emac_eth_probe(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_platdata(dev);
+ struct emac_eth_dev *priv = dev_get_priv(dev);
+
+ priv->regs = (struct emac_regs *)pdata->iobase;
+ sunxi_emac_board_setup(priv);
+
+ return sunxi_emac_init_phy(priv, dev);
+}
+
+static const struct eth_ops sunxi_emac_eth_ops = {
+ .start = sunxi_emac_eth_start,
+ .send = sunxi_emac_eth_send,
+ .recv = sunxi_emac_eth_recv,
+ .stop = sunxi_emac_eth_stop,
+};
+
+static int sunxi_emac_eth_ofdata_to_platdata(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_platdata(dev);
+
+ pdata->iobase = dev_get_addr(dev);
return 0;
}
+
+static const struct udevice_id sunxi_emac_eth_ids[] = {
+ { .compatible = "allwinner,sun4i-a10-emac" },
+ { }
+};
+
+U_BOOT_DRIVER(eth_sunxi_emac) = {
+ .name = "eth_sunxi_emac",
+ .id = UCLASS_ETH,
+ .of_match = sunxi_emac_eth_ids,
+ .ofdata_to_platdata = sunxi_emac_eth_ofdata_to_platdata,
+ .probe = sunxi_emac_eth_probe,
+ .ops = &sunxi_emac_eth_ops,
+ .priv_auto_alloc_size = sizeof(struct emac_eth_dev),
+ .platdata_auto_alloc_size = sizeof(struct eth_pdata),
+};
return v & AXP209_IRQ5_PEK_DOWN;
}
-
-static u8 axp209_get_gpio_ctrl_reg(unsigned int pin)
-{
- switch (pin) {
- case 0: return AXP209_GPIO0_CTRL;
- case 1: return AXP209_GPIO1_CTRL;
- case 2: return AXP209_GPIO2_CTRL;
- case 3: return AXP209_GPIO3_CTRL;
- }
- return 0;
-}
-
-int axp_gpio_direction_input(unsigned int pin)
-{
- if (pin == SUNXI_GPIO_AXP0_VBUS_DETECT)
- return 0;
-
- u8 reg = axp209_get_gpio_ctrl_reg(pin);
- /* GPIO3 is "special" */
- u8 val = (pin == 3) ? AXP209_GPIO3_INPUT : AXP209_GPIO_INPUT;
-
- return axp209_write(reg, val);
-}
-
-int axp_gpio_direction_output(unsigned int pin, unsigned int val)
-{
- u8 reg = axp209_get_gpio_ctrl_reg(pin);
-
- if (val) {
- val = (pin == 3) ? AXP209_GPIO3_OUTPUT_HIGH :
- AXP209_GPIO_OUTPUT_HIGH;
- } else {
- val = (pin == 3) ? AXP209_GPIO3_OUTPUT_LOW :
- AXP209_GPIO_OUTPUT_LOW;
- }
-
- return axp209_write(reg, val);
-}
-
-int axp_gpio_get_value(unsigned int pin)
-{
- u8 val, mask;
- int rc;
-
- if (pin == SUNXI_GPIO_AXP0_VBUS_DETECT) {
- rc = axp209_read(AXP209_POWER_STATUS, &val);
- mask = AXP209_POWER_STATUS_VBUS_USABLE;
- } else if (pin == 3) {
- rc = axp209_read(AXP209_GPIO3_CTRL, &val);
- mask = 1;
- } else {
- rc = axp209_read(AXP209_GPIO_STATE, &val);
- mask = 1 << (pin + 4);
- }
- if (rc)
- return rc;
-
- return (val & mask) ? 1 : 0;
-}
-
-int axp_gpio_set_value(unsigned int pin, unsigned int val)
-{
- return axp_gpio_direction_output(pin, val);
-}
#include <common.h>
#include <errno.h>
-#include <asm/arch/p2wi.h>
-#include <asm/arch/rsb.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/pmic_bus.h>
#include <axp221.h>
-/*
- * The axp221 uses the p2wi bus, the axp223 is identical (for all registers
- * used sofar) but uses the rsb bus. These functions abstract this.
- */
-static int pmic_bus_init(void)
-{
-#ifdef CONFIG_MACH_SUN6I
- p2wi_init();
- return p2wi_change_to_p2wi_mode(AXP221_CHIP_ADDR, AXP221_CTRL_ADDR,
- AXP221_INIT_DATA);
-#else
- int ret;
-
- ret = rsb_init();
- if (ret)
- return ret;
-
- return rsb_set_device_address(AXP223_DEVICE_ADDR, AXP223_RUNTIME_ADDR);
-#endif
-}
-
-static int pmic_bus_read(const u8 addr, u8 *data)
-{
-#ifdef CONFIG_MACH_SUN6I
- return p2wi_read(addr, data);
-#else
- return rsb_read(AXP223_RUNTIME_ADDR, addr, data);
-#endif
-}
-
-static int pmic_bus_write(const u8 addr, u8 data)
-{
-#ifdef CONFIG_MACH_SUN6I
- return p2wi_write(addr, data);
-#else
- return rsb_write(AXP223_RUNTIME_ADDR, addr, data);
-#endif
-}
-
static u8 axp221_mvolt_to_cfg(int mvolt, int min, int max, int div)
{
if (mvolt < min)
return (mvolt - min) / div;
}
-static int axp221_setbits(u8 reg, u8 bits)
-{
- int ret;
- u8 val;
-
- ret = pmic_bus_read(reg, &val);
- if (ret)
- return ret;
-
- val |= bits;
- return pmic_bus_write(reg, val);
-}
-
-static int axp221_clrbits(u8 reg, u8 bits)
-{
- int ret;
- u8 val;
-
- ret = pmic_bus_read(reg, &val);
- if (ret)
- return ret;
-
- val &= ~bits;
- return pmic_bus_write(reg, val);
-}
-
int axp221_set_dcdc1(unsigned int mvolt)
{
int ret;
u8 cfg = axp221_mvolt_to_cfg(mvolt, 1600, 3400, 100);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC1_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC1_EN);
ret = pmic_bus_write(AXP221_DCDC1_CTRL, cfg);
if (ret)
return ret;
- ret = axp221_setbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DCDC1SW_EN);
+ ret = pmic_bus_setbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DCDC1SW_EN);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC1_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC1_EN);
}
int axp221_set_dcdc2(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 600, 1540, 20);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC2_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC2_EN);
ret = pmic_bus_write(AXP221_DCDC2_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC2_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC2_EN);
}
int axp221_set_dcdc3(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 600, 1860, 20);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC3_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC3_EN);
ret = pmic_bus_write(AXP221_DCDC3_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC3_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC3_EN);
}
int axp221_set_dcdc4(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 600, 1540, 20);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC4_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC4_EN);
ret = pmic_bus_write(AXP221_DCDC4_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC4_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC4_EN);
}
int axp221_set_dcdc5(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 1000, 2550, 50);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC5_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC5_EN);
ret = pmic_bus_write(AXP221_DCDC5_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_DCDC5_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_DCDC5_EN);
}
int axp221_set_dldo1(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DLDO1_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DLDO1_EN);
ret = pmic_bus_write(AXP221_DLDO1_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DLDO1_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DLDO1_EN);
}
int axp221_set_dldo2(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DLDO2_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DLDO2_EN);
ret = pmic_bus_write(AXP221_DLDO2_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DLDO2_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DLDO2_EN);
}
int axp221_set_dldo3(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DLDO3_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DLDO3_EN);
ret = pmic_bus_write(AXP221_DLDO3_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DLDO3_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DLDO3_EN);
}
int axp221_set_dldo4(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DLDO4_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DLDO4_EN);
ret = pmic_bus_write(AXP221_DLDO4_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL2,
- AXP221_OUTPUT_CTRL2_DLDO4_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL2,
+ AXP221_OUTPUT_CTRL2_DLDO4_EN);
}
int axp221_set_aldo1(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_ALDO1_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_ALDO1_EN);
ret = pmic_bus_write(AXP221_ALDO1_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_ALDO1_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_ALDO1_EN);
}
int axp221_set_aldo2(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_ALDO2_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_ALDO2_EN);
ret = pmic_bus_write(AXP221_ALDO2_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL1,
- AXP221_OUTPUT_CTRL1_ALDO2_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL1,
+ AXP221_OUTPUT_CTRL1_ALDO2_EN);
}
int axp221_set_aldo3(unsigned int mvolt)
u8 cfg = axp221_mvolt_to_cfg(mvolt, 700, 3300, 100);
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL3,
- AXP221_OUTPUT_CTRL3_ALDO3_EN);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL3,
+ AXP221_OUTPUT_CTRL3_ALDO3_EN);
ret = pmic_bus_write(AXP221_ALDO3_CTRL, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL3,
- AXP221_OUTPUT_CTRL3_ALDO3_EN);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL3,
+ AXP221_OUTPUT_CTRL3_ALDO3_EN);
}
int axp221_set_eldo(int eldo_num, unsigned int mvolt)
}
if (mvolt == 0)
- return axp221_clrbits(AXP221_OUTPUT_CTRL2, bits);
+ return pmic_bus_clrbits(AXP221_OUTPUT_CTRL2, bits);
ret = pmic_bus_write(addr, cfg);
if (ret)
return ret;
- return axp221_setbits(AXP221_OUTPUT_CTRL2, bits);
+ return pmic_bus_setbits(AXP221_OUTPUT_CTRL2, bits);
}
int axp221_init(void)
return 0;
}
-
-int axp_gpio_direction_input(unsigned int pin)
-{
- switch (pin) {
- case SUNXI_GPIO_AXP0_VBUS_DETECT:
- return 0;
- default:
- return -EINVAL;
- }
-}
-
-int axp_gpio_direction_output(unsigned int pin, unsigned int val)
-{
- int ret;
-
- switch (pin) {
- case SUNXI_GPIO_AXP0_VBUS_ENABLE:
- ret = axp221_clrbits(AXP221_MISC_CTRL,
- AXP221_MISC_CTRL_N_VBUSEN_FUNC);
- if (ret)
- return ret;
-
- return axp_gpio_set_value(pin, val);
- default:
- return -EINVAL;
- }
-}
-
-int axp_gpio_get_value(unsigned int pin)
-{
- int ret;
- u8 val;
-
- switch (pin) {
- case SUNXI_GPIO_AXP0_VBUS_DETECT:
- ret = pmic_bus_read(AXP221_POWER_STATUS, &val);
- if (ret)
- return ret;
-
- return !!(val & AXP221_POWER_STATUS_VBUS_AVAIL);
- default:
- return -EINVAL;
- }
-}
-
-int axp_gpio_set_value(unsigned int pin, unsigned int val)
-{
- int ret;
-
- switch (pin) {
- case SUNXI_GPIO_AXP0_VBUS_ENABLE:
- if (val)
- ret = axp221_setbits(AXP221_VBUS_IPSOUT,
- AXP221_VBUS_IPSOUT_DRIVEBUS);
- else
- ret = axp221_clrbits(AXP221_VBUS_IPSOUT,
- AXP221_VBUS_IPSOUT_DRIVEBUS);
-
- if (ret)
- return ret;
- }
-
- return 0;
-}
/*
- * Copyright (C) 2014 Roman Byshko
+ * Sunxi ehci glue
*
- * Roman Byshko <rbyshko@gmail.com>
+ * Copyright (C) 2015 Hans de Goede <hdegoede@redhat.com>
+ * Copyright (C) 2014 Roman Byshko <rbyshko@gmail.com>
*
* Based on code from
* Allwinner Technology Co., Ltd. <www.allwinnertech.com>
* SPDX-License-Identifier: GPL-2.0+
*/
-#include <asm/arch/usbc.h>
#include <common.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/usb_phy.h>
+#include <asm/io.h>
#include "ehci.h"
int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr,
struct ehci_hcor **hcor)
{
- int err;
+ struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ int ahb_gate_offset;
- err = sunxi_usbc_request_resources(index + 1);
- if (err)
- return err;
+ ahb_gate_offset = index ? AHB_GATE_OFFSET_USB_EHCI1 :
+ AHB_GATE_OFFSET_USB_EHCI0;
+ setbits_le32(&ccm->ahb_gate0, 1 << ahb_gate_offset);
+#ifdef CONFIG_SUNXI_GEN_SUN6I
+ setbits_le32(&ccm->ahb_reset0_cfg, 1 << ahb_gate_offset);
+#endif
- sunxi_usbc_enable(index + 1);
- sunxi_usbc_vbus_enable(index + 1);
+ sunxi_usb_phy_init(index + 1);
+ sunxi_usb_phy_power_on(index + 1);
- *hccr = sunxi_usbc_get_io_base(index + 1);
+ if (index == 0)
+ *hccr = (void *)SUNXI_USB1_BASE;
+ else
+ *hccr = (void *)SUNXI_USB2_BASE;
*hcor = (struct ehci_hcor *)((uint32_t) *hccr
+ HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
int ehci_hcd_stop(int index)
{
- sunxi_usbc_vbus_disable(index + 1);
- sunxi_usbc_disable(index + 1);
+ struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+ int ahb_gate_offset;
- return sunxi_usbc_free_resources(index + 1);
+ sunxi_usb_phy_power_off(index + 1);
+ sunxi_usb_phy_exit(index + 1);
+
+ ahb_gate_offset = index ? AHB_GATE_OFFSET_USB_EHCI1 :
+ AHB_GATE_OFFSET_USB_EHCI0;
+#ifdef CONFIG_SUNXI_GEN_SUN6I
+ clrbits_le32(&ccm->ahb_reset0_cfg, 1 << ahb_gate_offset);
+#endif
+ clrbits_le32(&ccm->ahb_gate0, 1 << ahb_gate_offset);
+
+ return 0;
}
static inline u8 musb_read_configdata(void __iomem *mbase)
{
+#ifdef CONFIG_MACH_SUN8I_A33
+ /* <Sigh> allwinner saves a reg, and we need to hardcode this */
+ return 0xde;
+#else
musb_writeb(mbase, MUSB_INDEX, 0);
return musb_readb(mbase, 0x10 + MUSB_CONFIGDATA);
+#endif
}
static inline u16 musb_read_hwvers(void __iomem *mbase)
#include <common.h>
#include <watchdog.h>
#ifdef CONFIG_ARCH_SUNXI
-#include <asm/arch/usbc.h>
+#include <asm/arch/usb_phy.h>
#endif
#include <asm/errno.h>
#include <linux/usb/ch9.h>
* when clearing reset on low-speed devices, temporary disable
* squelch detection to work around this.
*/
- sunxi_usbc_enable_squelch_detect(0, 0);
+ sunxi_usb_phy_enable_squelch_detect(0, 0);
#endif
power = musb_readb(mbase, MUSB_POWER);
musb_writeb(mbase, MUSB_POWER, ~MUSB_POWER_RESET & power);
#ifdef CONFIG_ARCH_SUNXI
- sunxi_usbc_enable_squelch_detect(0, 1);
+ sunxi_usb_phy_enable_squelch_detect(0, 1);
#endif
host->isr(0, host);
host_speed = (musb_readb(mbase, MUSB_POWER) & MUSB_POWER_HSMODE) ?
*/
#include <common.h>
#include <asm/arch/cpu.h>
+#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
-#include <asm/arch/usbc.h>
+#include <asm/arch/usb_phy.h>
#include <asm-generic/gpio.h>
#include "linux-compat.h"
#include "musb_core.h"
if (is_host_enabled(musb)) {
/* port power on */
- sunxi_usbc_vbus_enable(0);
+ sunxi_usb_phy_power_on(0);
}
}
static void sunxi_musb_disable(struct musb *musb)
{
+ struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+
pr_debug("%s():\n", __func__);
/* Put the controller back in a pristane state for "usb reset" */
if (musb->is_active) {
- sunxi_usbc_disable(0);
- sunxi_usbc_enable(0);
+ sunxi_usb_phy_exit(0);
+#ifdef CONFIG_SUNXI_GEN_SUN6I
+ clrbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_GATE_OFFSET_USB0);
+#endif
+ clrbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_USB0);
+
+ mdelay(10);
+
+ setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_USB0);
+#ifdef CONFIG_SUNXI_GEN_SUN6I
+ setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_GATE_OFFSET_USB0);
+#endif
+ sunxi_usb_phy_init(0);
musb->is_active = 0;
}
}
static int sunxi_musb_init(struct musb *musb)
{
+ struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
int err;
pr_debug("%s():\n", __func__);
- err = sunxi_usbc_request_resources(0);
- if (err)
- return err;
-
if (is_host_enabled(musb)) {
- err = sunxi_usbc_vbus_detect(0);
+ err = sunxi_usb_phy_vbus_detect(0);
if (err) {
eprintf("Error: A charger is plugged into the OTG\n");
- sunxi_usbc_free_resources(0);
return -EIO;
}
}
musb->isr = sunxi_musb_interrupt;
- sunxi_usbc_enable(0);
+
+ setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_USB0);
+#ifdef CONFIG_SUNXI_GEN_SUN6I
+ setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_GATE_OFFSET_USB0);
+#endif
+ sunxi_usb_phy_init(0);
USBC_ConfigFIFO_Base();
USBC_EnableDpDmPullUp(musb->mregs);
USBC_DisableDpDmPullUp(musb->mregs);
USBC_DisableIdPullUp(musb->mregs);
- sunxi_usbc_vbus_disable(0);
- sunxi_usbc_disable(0);
+ sunxi_usb_phy_power_off(0);
+ sunxi_usb_phy_exit(0);
- return sunxi_usbc_free_resources(0);
+ return 0;
}
const struct musb_platform_ops sunxi_musb_ops = {
CCM_HDMI_CTRL_PLL3);
/* Set ahb gating to pass */
-#ifdef CONFIG_MACH_SUN6I
+#ifdef CONFIG_SUNXI_GEN_SUN6I
setbits_le32(&ccm->ahb_reset1_cfg, 1 << AHB_RESET_OFFSET_HDMI);
#endif
setbits_le32(&ccm->ahb_gate1, 1 << AHB_GATE_OFFSET_HDMI);
clrbits_le32(&hdmi->ctrl, SUNXI_HDMI_CTRL_ENABLE);
clrbits_le32(&ccm->hdmi_clk_cfg, CCM_HDMI_CTRL_GATE);
clrbits_le32(&ccm->ahb_gate1, 1 << AHB_GATE_OFFSET_HDMI);
-#ifdef CONFIG_MACH_SUN6I
+#ifdef CONFIG_SUNXI_GEN_SUN6I
clrbits_le32(&ccm->ahb_reset1_cfg, 1 << AHB_RESET_OFFSET_HDMI);
#endif
clock_set_pll3(0);
sunxi_frontend_init();
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
+#ifdef CONFIG_SUNXI_GEN_SUN6I
/* Reset off */
setbits_le32(&ccm->ahb_reset1_cfg, 1 << AHB_RESET_OFFSET_DE_BE0);
#endif
(struct sunxi_lcdc_reg *)SUNXI_LCD0_BASE;
/* Reset off */
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
+#ifdef CONFIG_SUNXI_GEN_SUN6I
setbits_le32(&ccm->ahb_reset1_cfg, 1 << AHB_RESET_OFFSET_LCD0);
#else
setbits_le32(&ccm->lcd0_ch0_clk_cfg, CCM_LCD_CH0_CTRL_RST);
* white while the lcd inits.
*/
pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_EN);
- if (pin != -1) {
+ if (pin >= 0) {
gpio_request(pin, "lcd_backlight_enable");
gpio_direction_output(pin, 0);
}
pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_PWM);
- if (pin != -1) {
+ if (pin >= 0) {
gpio_request(pin, "lcd_backlight_pwm");
gpio_direction_output(pin, PWM_OFF);
}
reset_pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_RESET);
- if (reset_pin != -1) {
+ if (reset_pin >= 0) {
gpio_request(reset_pin, "lcd_reset");
gpio_direction_output(reset_pin, 0); /* Assert reset */
}
/* Give the backlight some time to turn off and power up the panel. */
mdelay(40);
pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_POWER);
- if (pin != -1) {
+ if (pin >= 0) {
gpio_request(pin, "lcd_power");
gpio_direction_output(pin, 1);
}
- if (reset_pin != -1)
+ if (reset_pin >= 0)
gpio_direction_output(reset_pin, 1); /* De-assert reset */
}
mdelay(40);
pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_EN);
- if (pin != -1)
+ if (pin >= 0)
gpio_direction_output(pin, 1);
pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_PWM);
- if (pin != -1)
+ if (pin >= 0)
gpio_direction_output(pin, PWM_ON);
}
static void sunxi_drc_init(void)
{
-#if defined CONFIG_MACH_SUN6I || defined CONFIG_MACH_SUN8I
+#ifdef CONFIG_SUNXI_GEN_SUN6I
struct sunxi_ccm_reg * const ccm =
(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
/* On sun6i the drc must be clocked even when in pass-through mode */
+#ifdef CONFIG_MACH_SUN8I_A33
+ setbits_le32(&ccm->ahb_reset1_cfg, 1 << AHB_RESET_OFFSET_SAT);
+#endif
setbits_le32(&ccm->ahb_reset1_cfg, 1 << AHB_RESET_OFFSET_DRC0);
clock_set_de_mod_clock(&ccm->iep_drc0_clk_cfg, 300000000);
#endif
int pin;
pin = sunxi_name_to_gpio(CONFIG_VIDEO_VGA_EXTERNAL_DAC_EN);
- if (pin != -1) {
+ if (pin >= 0) {
gpio_request(pin, "vga_enable");
gpio_direction_output(pin, 1);
}
#define AXP152_POWEROFF (1 << 7)
+/* For axp_gpio.c */
+#define AXP_GPIO0_CTRL 0x90
+#define AXP_GPIO1_CTRL 0x91
+#define AXP_GPIO2_CTRL 0x92
+#define AXP_GPIO3_CTRL 0x93
+#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
+#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
+#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
+#define AXP_GPIO_STATE 0x97
+#define AXP_GPIO_STATE_OFFSET 0
+
int axp152_set_dcdc2(int mvolt);
int axp152_set_dcdc3(int mvolt);
int axp152_set_dcdc4(int mvolt);
AXP209_IRQ_ENABLE5 = 0x44,
AXP209_IRQ_STATUS5 = 0x4c,
AXP209_SHUTDOWN = 0x32,
- AXP209_GPIO0_CTRL = 0x90,
- AXP209_GPIO1_CTRL = 0x92,
- AXP209_GPIO2_CTRL = 0x93,
- AXP209_GPIO_STATE = 0x94,
- AXP209_GPIO3_CTRL = 0x95,
};
#define AXP209_POWER_STATUS_ON_BY_DC (1 << 0)
#define AXP209_POWEROFF (1 << 7)
-#define AXP209_GPIO_OUTPUT_LOW 0x00 /* Drive pin low */
-#define AXP209_GPIO_OUTPUT_HIGH 0x01 /* Drive pin high */
-#define AXP209_GPIO_INPUT 0x02 /* Float pin */
-
-/* GPIO3 is different from the others */
-#define AXP209_GPIO3_OUTPUT_LOW 0x00 /* Drive pin low, Output mode */
-#define AXP209_GPIO3_OUTPUT_HIGH 0x02 /* Float pin, Output mode */
-#define AXP209_GPIO3_INPUT 0x06 /* Float pin, Input mode */
-
-#define AXP_GPIO
+/* For axp_gpio.c */
+#define AXP_POWER_STATUS 0x00
+#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
+#define AXP_GPIO0_CTRL 0x90
+#define AXP_GPIO1_CTRL 0x92
+#define AXP_GPIO2_CTRL 0x93
+#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
+#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
+#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
+#define AXP_GPIO_STATE 0x94
+#define AXP_GPIO_STATE_OFFSET 4
extern int axp209_set_dcdc2(int mvolt);
extern int axp209_set_dcdc3(int mvolt);
extern int axp209_init(void);
extern int axp209_poweron_by_dc(void);
extern int axp209_power_button(void);
-
-extern int axp_gpio_direction_input(unsigned int pin);
-extern int axp_gpio_direction_output(unsigned int pin, unsigned int val);
-extern int axp_gpio_get_value(unsigned int pin);
-extern int axp_gpio_set_value(unsigned int pin, unsigned int val);
* SPDX-License-Identifier: GPL-2.0+
*/
-#define AXP221_CHIP_ADDR 0x68
-#define AXP221_CTRL_ADDR 0x3e
-#define AXP221_INIT_DATA 0x3e
-
-#define AXP223_DEVICE_ADDR 0x3a3
-#define AXP223_RUNTIME_ADDR 0x2d
-
/* Page 0 addresses */
-#define AXP221_POWER_STATUS 0x00
-#define AXP221_POWER_STATUS_VBUS_AVAIL (1 << 5)
-#define AXP221_POWER_STATUS_VBUS_USABLE (1 << 4)
#define AXP221_CHIP_ID 0x03
#define AXP221_OUTPUT_CTRL1 0x10
#define AXP221_OUTPUT_CTRL1_DCDC0_EN (1 << 0)
/* Page 1 addresses */
#define AXP221_SID 0x20
-#define AXP_GPIO
+/* For axp_gpio.c */
+#define AXP_POWER_STATUS 0x00
+#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
+#define AXP_GPIO0_CTRL 0x90
+#define AXP_GPIO1_CTRL 0x92
+#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
+#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
+#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
+#define AXP_GPIO_STATE 0x94
+#define AXP_GPIO_STATE_OFFSET 0
int axp221_set_dcdc1(unsigned int mvolt);
int axp221_set_dcdc2(unsigned int mvolt);
int axp221_set_eldo(int eldo_num, unsigned int mvolt);
int axp221_init(void);
int axp221_get_sid(unsigned int *sid);
-
-int axp_gpio_direction_input(unsigned int pin);
-int axp_gpio_direction_output(unsigned int pin, unsigned int val);
-int axp_gpio_get_value(unsigned int pin);
-int axp_gpio_set_value(unsigned int pin, unsigned int val);
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif
+#define CONFIG_SUNXI_USB_PHYS 3
+
/*
* Include common sunxi configuration where most the settings are
*/
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
+#define CONFIG_SUNXI_USB_PHYS 2
+
/*
* Include common sunxi configuration where most the settings are
*/
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif
+#define CONFIG_SUNXI_USB_PHYS 3
+
/*
* Include common sunxi configuration where most the settings are
*/
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif
+#define CONFIG_SUNXI_USB_PHYS 3
+
#define CONFIG_ARMV7_PSCI 1
#define CONFIG_ARMV7_SECURE_BASE SUNXI_SRAM_B_BASE
#define CONFIG_TIMER_CLK_FREQ 24000000
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
+#define CONFIG_SUNXI_USB_PHYS 2
+
/*
* Include common sunxi configuration where most the settings are
*/
#define CONFIG_SYS_TEXT_BASE 0x4a000000
-#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_DM)
+#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_DM_SERIAL)
# define CONFIG_DW_SERIAL
#endif
#define CONFIG_SPL_I2C_SUPPORT
#endif
-#define CONFIG_SYS_I2C
#if defined CONFIG_I2C0_ENABLE || defined CONFIG_I2C1_ENABLE || \
defined CONFIG_I2C2_ENABLE || defined CONFIG_I2C3_ENABLE || \
defined CONFIG_I2C4_ENABLE
+#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
-#endif
#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_SLAVE 0x7f
+#define CONFIG_CMD_I2C
+#endif
#if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
#define CONFIG_SYS_I2C_SOFT
#define CONFIG_VIDEO_LCD_I2C_BUS -1 /* NA, but necessary to compile */
#endif
-#define CONFIG_CMD_I2C
-
/* PMU */
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined CONFIG_AXP221_POWER
#define CONFIG_SPL_POWER_SUPPORT
/* Ethernet support */
#ifdef CONFIG_SUNXI_EMAC
+#define CONFIG_PHY_ADDR 1
#define CONFIG_MII /* MII PHY management */
+#define CONFIG_PHYLIB
#endif
#ifdef CONFIG_SUNXI_GMAC
#define CONFIG_EXTRA_ENV_SETTINGS \
CONSOLE_ENV_SETTINGS \
MEM_LAYOUT_ENV_SETTINGS \
- "fdtfile=" CONFIG_FDTFILE "\0" \
+ "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"console=ttyS0,115200\0" \
BOOTENV
--- /dev/null
+/*
+ * Copyright 2014 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DT_BINDINGS_DMA_SUN4I_A10_H_
+#define __DT_BINDINGS_DMA_SUN4I_A10_H_
+
+#define SUN4I_DMA_NORMAL 0
+#define SUN4I_DMA_DEDICATED 1
+
+#endif /* __DT_BINDINGS_DMA_SUN4I_A10_H_ */
--- /dev/null
+/*
+ * Copyright 2014 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef __DT_BINDINGS_PINCTRL_SUN4I_A10_H_
+#define __DT_BINDINGS_PINCTRL_SUN4I_A10_H_
+
+#define SUN4I_PINCTRL_10_MA 0
+#define SUN4I_PINCTRL_20_MA 1
+#define SUN4I_PINCTRL_30_MA 2
+#define SUN4I_PINCTRL_40_MA 3
+
+#define SUN4I_PINCTRL_NO_PULL 0
+#define SUN4I_PINCTRL_PULL_UP 1
+#define SUN4I_PINCTRL_PULL_DOWN 2
+
+#endif /* __DT_BINDINGS_PINCTRL_SUN4I_A10_H_ */
--- /dev/null
+/*
+ * This header provides constants for most thermal bindings.
+ *
+ * Copyright (C) 2013 Texas Instruments
+ * Eduardo Valentin <eduardo.valentin@ti.com>
+ *
+ * GPLv2 only
+ */
+
+#ifndef _DT_BINDINGS_THERMAL_THERMAL_H
+#define _DT_BINDINGS_THERMAL_THERMAL_H
+
+/* On cooling devices upper and lower limits */
+#define THERMAL_NO_LIMIT (~0)
+
+#endif
+
int skge_initialize(bd_t *bis);
int smc91111_initialize(u8 dev_num, int base_addr);
int smc911x_initialize(u8 dev_num, int base_addr);
-int sunxi_emac_initialize(bd_t *bis);
-int sunxi_gmac_initialize(bd_t *bis);
int tsi108_eth_initialize(bd_t *bis);
int uec_standard_init(bd_t *bis);
int uli526x_initialize(bd_t *bis);
projects / platform / kernel / u-boot.git / commitdiff