+commit d62f64cc23a940eafe712c776b3249e4160753d1
+Author: Wolfgang Denk <wd@denx.de>
+Date: Wed May 16 00:13:33 2007 +0200
+
+ Coding Style Cleanup, new CHANGELOG
+
+commit 7d98ba770a7eaefa29ce927f31a0956df85bf650
+Author: Piotr Kruszynski <ppk@semihalf.com>
+Date: Thu May 10 16:55:52 2007 +0200
+
+ [Motion-PRO] Add MTD and JFFS2 support, also add default partition
+ definition.
+
+commit e69f66c6ebe82bbbd1da766bc4eda40ec7ee5af1
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue May 8 15:57:43 2007 +0200
+
+ add: reading special purpose registers
+
+commit 1a50f164beb065f360fbddb76029607d6b099698
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue May 8 14:52:52 2007 +0200
+
+ add: Microblaze V5 exception handling
+
+commit ab874d5047e5d30dbc1e517ff26083efffa98ecb
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue May 8 14:39:11 2007 +0200
+
+ add: FSL control read and write
+
+commit de1de02a7cbf05e6b63e0d8ffc624f12493f6ba3
+Author: Piotr Kruszynski <ppk@semihalf.com>
+Date: Tue May 8 13:05:44 2007 +0200
+
+ [Motion-PRO] Add support for I2C, EEPROM and RTC.
+
+commit fa5c2ba123b1bf88455bfc21db5e786ca045029d
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Tue May 8 10:23:56 2007 +0200
+
+ [Motion-PRO] Add ATA support. Add CF-booting commands to the default
+ environment.
+
+commit 06241d50a3ab1b20a0b08baeeaffcaa23ae4b839
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Tue May 8 09:39:12 2007 +0200
+
+ [Motion-PRO] Change IPB clock frequency from 50MHz to 100MHz. This
+ eliminates networking problems in Linux (timeouts).
+
+commit 1f1369c34b629be94702684d41d3fddf0f6193e7
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Tue May 8 09:21:57 2007 +0200
+
+ [Motion-PRO] Enable Flat Device Tree support and modify default environment
+ to allow booting of FDT-expecting kernels.
+
+commit fb05f6da35ea1c15c553abe6f23f656bf18dc5db
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 23:58:31 2007 +0200
+
+ new: USE_MSR_INTR support
+
+commit 008861a2f3ef2c062744d733787c7e530a1b8761
+Author: Bartlomiej Sieka <tur@semihalf.com>
+Date: Mon May 7 22:36:15 2007 +0200
+
+ [MPC5xxx] There are networking problems on the Motion-PRO board with
+ current PHY initalization code (tftp timeouts all the time). This commit
+ temporarily disables PHY initalization sequence to make the networking
+ operational, until a fix is found.
+
+commit abca901869c3760b6c5fecb825db6c1d91a78a93
+Author: Wolfgang Denk <wd@denx.de>
+Date: Mon May 7 22:10:36 2007 +0200
+
+ Get rid of duplicated file (see include/configs/sbc8560.h instead)
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit 207b7b2c9d9752e0f6478c30c29b7087f6e6cbb6
+Author: Wolfgang Denk <wd@denx.de>
+Date: Mon May 7 22:07:08 2007 +0200
+
+ Get rid of duplicated file (see doc/README.SBC8560 instead)
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
+commit a7bac7e9b57ba948051beb19ec5be3a75ce75383
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:43:10 2007 +0200
+
+ fix: read and write MSR - repair number of parameters
+
+commit 19bf1fbad7f19d5a120be9b1daf136e052fcab39
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:33:51 2007 +0200
+
+ new: fsl interrupt support
+ FSL_Has_data is connected to INTC.
+
+commit 792032baa7d625e34c981ab6df521911bd8dc861
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:30:12 2007 +0200
+
+ fix: interrupt handler
+ remove asm code
+
+commit f3f001a341ef185d0f13841be5b5dc3395aacc31
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:25:08 2007 +0200
+
+ fix: remove asm code
+
+commit fb7c2dbef02c9f6f8d7b04ec4c2bfb91418b9c01
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 19:12:43 2007 +0200
+
+ fix: clean interrupt
+
+commit 42efed6130c8fcf7da881385b5427065d2801757
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 17:22:25 2007 +0200
+
+ fix: interrupt handler for multiple sources
+
+commit 48fbd3a4cdabbebc1debd7eed73c00c2caf914f6
+Author: Michal Simek <monstr@monstr.eu>
+Date: Mon May 7 17:11:09 2007 +0200
+
+ new: add writing to msr register
+
+commit ac4cd59d59c9bf3f89cb7a344abf8184d678f562
+Author: Timur Tabi <timur@freescale.com>
+Date: Sat May 5 08:12:30 2007 +0200
+
+ 5xxx: write MAC address to mac-address and local-mac-address
+
+ Some device trees have a mac-address property, some have local-mac-address,
+ and some have both. To support all of these device trees, ftp_cpu_setup()
+ should write the MAC address to mac-address and local-mac-address, if they
+ exist.
+
+ Signed-off-by: Timur Tabi <timur@freescale.com>
+ Acked-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit a9d87e2707dcb249f6bb7f7ff7e00acd8cda9fd2
+Author: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
+Date: Sun Apr 29 14:01:54 2007 +0200
+
+ [PATCH] Use PVR to distinguish MPC5200B from MPC5200 in boot message
+
+ MPC5200B systems are incorrectly reported as MPC5200 in U-Boot start-up
+ message. Use PVR to distinguish between the two variants, and print proper CPU
+ information.
+
+ Signed-off-by: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
+ Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
+ Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
+
+commit 4ec5bd55ed1ffa91a774af298769621f4fbb18c1
+Author: Ladislav Michl <ladis@linux-mips.org>
+Date: Wed Apr 25 16:01:26 2007 +0200
+
+ [PATCH] simplify silent console
+
+ Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit b7598a43f2b421a713d8135e98a42c37d9eb9df0
+Author: Sergei Shtylyov <sshtylyov@ru.mvista.com>
+Date: Mon Apr 23 15:30:39 2007 +0200
+
+ [PATCH] Avoid assigning PCI resources from zero address
+
+ If a PCI IDE card happens to get a zero address assigned to it, the Linux IDE
+ core complains and IDE drivers fails to work. Also, assigning zero to a BAR
+ was illegal according to PCI 2.1 (the later revisions seem to have excluded the
+ sentence about "0" being considered an invalid address) -- so, use a reasonable
+ starting value of 0x1000 (that's what the most Linux archs are using).
+
+ Alternatively, one might have fixed the calls to pci_set_region() individually
+ (some code even seems to have taken care of this issue) but that would have
+ been a lot more work. :-)
+
+ Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit 9ffd451afeb08e5be7ddae680487ec962b2bca25
+Author: Jeffrey Mann <mannj@embeddedplanet.com>
+Date: Mon Apr 23 14:00:11 2007 +0200
+
+ [patch] setenv(...) can delete environmentalvariables
+
+ update setenv() function so that entering a NULL value for the
+ variable's value will delete the environmental variable
+
+ Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
+ Acked-by: Stefan Roese <sr@denx.de>
+
+commit ebd0a0ae05a44769c4e27458ad4e9f3438250443
+Author: Mike Frysinger <vapier@gentoo.org>
+Date: Mon Apr 23 13:54:24 2007 +0200
+
+ [patch] use unsigned char in smc91111 driver for mac
+
+ the v_mac variable in the smc91111 driver is declared as a signed char ...
+ this causes problems when one of the bytes in the MAC is "signed" like 0xE0
+ because when it gets printed out, you get a display like:
+ 0xFFFFFFE0 and that's no good
+
+ Signed-off-by: Mike Frysinger <vapier@gentoo.org>
+
+commit ffc50f9bb194343c6303517a517708457a5eb6b8
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat May 5 18:54:42 2007 +0200
+
+ new: FSL and MSR support #2
+
+commit f7e2e0eb0668136305f78bb9c21be79b48a34247
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat May 5 18:27:16 2007 +0200
+
+ new: FSL and MSR support
+
+commit 2f15278c2eb911c668b4fe562130b78cf554d139
+Author: Wolfgang Denk <wd@denx.de>
+Date: Sat May 5 18:23:11 2007 +0200
+
+ Coding stylke cleanup; update CHANGELOG.
+
+ Signed-off-by: Wolfgang Denk <wd@denx.de>
+
commit 885ec89b648a899a2f32393fd3ffd9f7234c4402
Author: Wolfgang Denk <wd@denx.de>
Date: Sat May 5 18:05:02 2007 +0200
Signed-off-by: Wolfgang Denk <wd@denx.de>
+commit 068aab660bc3912b930be5540e6b3f3fd6ad3c96
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Thu May 3 19:43:52 2007 -0500
+
+ mpc83xx: fix trivial error in MAKEALL
+
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+
commit c64a89d6ce8584b9fc64f4e85da9ecac3cfc2c2a
Author: Wolfgang Denk <wd@denx.de>
Date: Thu May 3 16:34:41 2007 +0200
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
+commit f64702b7fc8f8df39d31add770df6e372f9e9ce3
+Author: Timur Tabi <timur@freescale.com>
+Date: Mon Apr 30 13:59:50 2007 -0500
+
+ Fix memory initialization on MPC8349E-mITX
+
+ Define CFG_DDR_SDRAM_CLK_CNTL for the MPC8349E-mITX and MPC8349E-mITX-GP.
+ This allows ddr->sdram_clk_cntl to be properly initialized. This is necessary
+ on some ITX boards, notably those with a revision 3.1 CPU.
+
+ Also change spd_sdram() in cpu/mpc83xx/spd_sdram.c to not write anything into
+ ddr->sdram_clk_cntl if CFG_DDR_SDRAM_CLK_CNTL is not defined.
+
+ Signed-off-by: Timur Tabi <timur@freescale.com>
+ Acked-by: Michael Benedict <MBenedict@twacs.com>
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+
+commit 54b2d434ae9d01787936f34fe1759cf3d7624ae3
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Mon Apr 30 15:26:21 2007 -0500
+
+ mpc83xx: replace elaborate boottime verbosity with 'clocks' command
+
+ and fix CPU: to align with Board: display text.
+
+ Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
+
commit c1ab82669d9525998c34e802a12cad662723f22a
Author: James Yang <James.Yang@freescale.com>
Date: Fri Mar 16 13:02:53 2007 -0500
Signed-off-by: Stefan Roese <sr@denx.de>
+commit 5c5d3242935cf3543af01142627494434834cf98
+Author: Kim Phillips <kim.phillips@freescale.com>
+Date: Wed Apr 25 12:34:38 2007 -0500
+
+ mpc83xx: minor fixups for 8313rdb introduction
+
+commit 144876a380f5756f57412caf74c1d6dc201dd796
+Author: Michal Simek <monstr@monstr.eu>
+Date: Tue Apr 24 23:01:02 2007 +0200
+
+ [PATCH] MTD partition support, JFFS2 support
+
commit 37ed6cdd4159195bfad68d8a237f6adda8f482cb
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Tue Apr 24 14:03:45 2007 +0200
board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
+commit 96b8a05432f346f36493535c85320b70ec9c7c1b
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:54:15 2007 -0500
+
+ mpc83xx: Add MPC8313ERDB support.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 49ea3b6eafe606285ae4d5c378026153dde53200
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:21 2007 -0500
+
+ mpc83xx: Add generic PCI setup code.
+
+ Board code can now request the generic setup code rather than having to
+ copy-and-paste it for themselves. Boards should be converted to use this
+ once they're tested with it.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 7c98e5193e93df6b9b651851d54b638a61ebb0ea
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:19 2007 -0500
+
+ mpc83xx: Add 831x support to speed.c.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 0f253283a32d91e06844d7f87f9b33f4f4fbce8f
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:18 2007 -0500
+
+ mpc83xx: Add 831x support to global_data.h
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit 95e7ef897e54591e615fc1b458b74c286fe1fb06
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:16 2007 -0500
+
+ mpc83xx: Change PVR_83xx to PVR_E300C1-3, and update checkcpu().
+
+ Rather than misleadingly define PVR_83xx as the specific type of 83xx
+ being built for, the PVR of each core revision is defined. checkcpu() now
+ prints the core that it detects, rather than aborting if it doesn't find
+ what it thinks it wants.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit a35b0c4950d84cf9e3a9e32b916135956d1ac636
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:34:15 2007 -0500
+
+ mpc83xx: Recognize SPR values for MPC8311 and MPC8313.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
+commit d87c57b201b4572d16f1b642998faa00c9912b16
+Author: Scott Wood <scottwood@freescale.com>
+Date: Mon Apr 16 14:31:55 2007 -0500
+
+ mpc83xx: Add register definitions for MPC831x.
+
+ Signed-off-by: Scott Wood <scottwood@freescale.com>
+
commit 323bfa8f436dc3bc57187c9b1488bc3146ff1522
Author: Stefan Roese <sr@denx.de>
Date: Mon Apr 23 12:00:22 2007 +0200
Signed-off-by: Stefan Roese <sr@denx.de>
+commit 32556443840f127170e4baa8bdd5b567039f6c36
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat Apr 21 21:07:22 2007 +0200
+
+ [PATCH] SystemACE support for Microblaze
+
+commit 0643631aa1036cd746bf5d15f5a34bc7bc01ea4f
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat Apr 21 21:02:40 2007 +0200
+
+ 16bit read/write little endian
+
+commit 9d1d6a34d26c5933bc097ce73c9348f95573cdd4
+Author: Michal Simek <monstr@monstr.eu>
+Date: Sat Apr 21 20:53:31 2007 +0200
+
+ Change ML401 parameters - Xilinx BSP
+
commit 2e343b9a57f32e1bd08c35c9976910333fb4e13d
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed Feb 28 05:37:29 2007 -0600
Signed-of-by: Greg Lopp <lopp@pobox.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
+commit 6fbf261f8df294e589cfadebebe5468e3c0f29e9
+Author: Xie Xiaobo <r63061@freescale.com>
+Date: Fri Mar 9 19:08:25 2007 +0800
+
+ Fix two bugs for MPC83xx DDR2 controller SPD Init
+
+ There are a few bugs in the cpu/mpc83xx/spd_sdram.c
+ the first bug is that the picos_to_clk routine introduces a huge
+ rounding error in 83xx.
+ the second bug is that the mode register write recovery field is
+ tWR-1, not tWR >> 1.
+
commit 2ad3aba01d37b72e7c957b07e102fccd64fe6d13
Author: Jeffrey Mann <mannj@embeddedplanet.com>
Date: Thu Apr 12 14:15:59 2007 +0200
#########################################################################
LIST_83xx=" \
- MPC832XEMDS MPC8349EMDS MPC8349ITX MPC8349ITXGP \
- MPC8360EMDS sbc8349 TQM834x \
+ MPC8313ERDB MPC832XEMDS MPC8349EMDS MPC8349ITX \
+ MPC8349ITXGP MPC8360EMDS sbc8349 TQM834x \
"
## MPC83xx Systems
#########################################################################
+MPC8313ERDB_33_config \
+MPC8313ERDB_66_config: unconfig
+ @echo "" >include/config.h ; \
+ if [ "$(findstring _33_,$@)" ] ; then \
+ echo -n "...33M ..." ; \
+ echo "#define CFG_33MHZ" >>include/config.h ; \
+ fi ; \
+ if [ "$(findstring _66_,$@)" ] ; then \
+ echo -n "...66M..." ; \
+ echo "#define CFG_66MHZ" >>include/config.h ; \
+ fi ;
+ @$(MKCONFIG) -a MPC8313ERDB ppc mpc83xx mpc8313erdb
+
MPC832XEMDS_config \
MPC832XEMDS_HOST_33_config \
MPC832XEMDS_HOST_66_config \
CFG_CMD_VFD * VFD support (TRAB)
CFG_CMD_BSP * Board SPecific functions
CFG_CMD_CDP * Cisco Discover Protocol support
+ CFG_CMD_FSL * Microblaze FSL support
-----------------------------------------------
CFG_CMD_ALL all
acadia_gpio_init();
+ /* Configure 405EZ for NAND usage */
+ mtsdr(sdrnand0, 0x80c00000);
+ mtsdr(sdrultra0, 0x8d110000);
+
/* USB Host core needs this bit set */
mfsdr(sdrultra1, reg);
mtsdr(sdrultra1, reg | SDR_ULTRA1_LEDNENABLE);
int checkboard(void)
{
char *s = getenv("serial#");
+ u8 rev;
+
+ rev = in8(CFG_CPLD_BASE + 0);
+ printf("Board: Acadia - AMCC PPC405EZ Evaluation Board, Rev. %X", rev);
- printf("Board: Acadia - AMCC PPC405EZ Evaluation Board");
if (s != NULL) {
puts(", serial# ");
puts(s);
(0x80000000 >> (28 + CFG_NAND_CS));
mtsdr(SDR0_CUST0, sdr0_cust0);
+ /* Update EBC speed after booting from i2c bootstrap settings
+ * on newer boards with 33.333 MHZ Clocks
+ */
+ if (in8(CFG_BCSR_BASE + 3) & 0x80)
+ mtcpr(0xe0, 0x02000000);
+
return 0;
}
printf("Board: Rainier - AMCC PPC440GRx Evaluation Board");
#endif
- rev = *(u8 *)(CFG_BCSR_BASE + 0);
- val = *(u8 *)(CFG_BCSR_BASE + 5) & 0x01;
+ rev = in8(CFG_BCSR_BASE + 0);
+ val = in8(CFG_BCSR_BASE + 5) & 0x01;
printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33);
if (s != NULL) {
#include <common.h>
#include <mpc5xxx.h>
+#include <miiphy.h>
+#if defined(CONFIG_OF_FLAT_TREE)
+#include <ft_build.h>
+#endif
+#if defined(CONFIG_STATUS_LED)
+#include <status_led.h>
+#endif /* CONFIG_STATUS_LED */
/* Kollmorgen DPR initialization data */
struct init_elem {
}
+/*
+ * Additional PHY intialization. After being reset in mpc5xxx_fec_init_phy(),
+ * PHY goes into FX mode. To take it out of the FX mode and switch into
+ * desired TX operation, one needs to clear the FX_SEL bit of Mode Control
+ * Register.
+ */
+void reset_phy(void)
+{
+ unsigned short mode_control;
+
+ miiphy_read("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15, &mode_control);
+ miiphy_write("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15,
+ mode_control & 0xfffe);
+ return;
+}
+
#ifndef CFG_RAMBOOT
/*
* Helper function to initialize SDRAM controller.
*/
-static void sdram_start (int hi_addr)
+static void sdram_start(int hi_addr)
{
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
/*
* Initalize SDRAM - configure SDRAM controller, detect memory size.
*/
-long int initdram (int board_type)
+long int initdram(int board_type)
{
ulong dramsize = 0;
#ifndef CFG_RAMBOOT
}
-int checkboard (void)
+int checkboard(void)
{
- puts("Board: Promess Motion-PRO board\n");
+ uchar rev = *(vu_char *)CPLD_REV_REGISTER;
+ printf("Board: Promess Motion-PRO board (CPLD rev. 0x%02x)\n", rev);
return 0;
}
+
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+}
+#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */
+
+
+#if defined(CONFIG_STATUS_LED)
+void __led_init(led_id_t regaddr, int state)
+{
+ *((vu_long *) regaddr) |= ENABLE_GPIO_OUT;
+
+ if (state == STATUS_LED_ON)
+ *((vu_long *) regaddr) |= LED_ON;
+ else
+ *((vu_long *) regaddr) &= ~LED_ON;
+}
+
+void __led_set(led_id_t regaddr, int state)
+{
+ if (state == STATUS_LED_ON)
+ *((vu_long *) regaddr) |= LED_ON;
+ else
+ *((vu_long *) regaddr) &= ~LED_ON;
+}
+
+void __led_toggle(led_id_t regaddr)
+{
+ *((vu_long *) regaddr) ^= LED_ON;
+}
+#endif /* CONFIG_STATUS_LED */
--- /dev/null
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) crv $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+TEXT_BASE = 0xFE000000
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ft_build.h>
+#include <pci.h>
+#include <mpc83xx.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+#ifndef CFG_8313ERDB_BROKEN_PMC
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ gd->flags |= GD_FLG_SILENT;
+#endif
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: Freescale MPC8313ERDB\n");
+ return 0;
+}
+
+static struct pci_region pci_regions[] = {
+ {
+ bus_start: CFG_PCI1_MEM_BASE,
+ phys_start: CFG_PCI1_MEM_PHYS,
+ size: CFG_PCI1_MEM_SIZE,
+ flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+ },
+ {
+ bus_start: CFG_PCI1_MMIO_BASE,
+ phys_start: CFG_PCI1_MMIO_PHYS,
+ size: CFG_PCI1_MMIO_SIZE,
+ flags: PCI_REGION_MEM
+ },
+ {
+ bus_start: CFG_PCI1_IO_BASE,
+ phys_start: CFG_PCI1_IO_PHYS,
+ size: CFG_PCI1_IO_SIZE,
+ flags: PCI_REGION_IO
+ }
+};
+
+void pci_init_board(void)
+{
+ volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+ volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+ volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+ struct pci_region *reg[] = { pci_regions };
+ int warmboot;
+
+ /* Enable all 3 PCI_CLK_OUTPUTs. */
+ clk->occr |= 0xe0000000;
+
+ /*
+ * Configure PCI Local Access Windows
+ */
+ pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR;
+ pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+ pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR;
+ pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+ warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+#ifndef CFG_8313ERDB_BROKEN_PMC
+ warmboot |= immr->pmc.pmccr1 & PMCCR1_POWER_OFF;
+#endif
+
+ mpc83xx_pci_init(1, reg, warmboot);
+}
+
+#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+
+#ifdef CONFIG_PCI
+ ft_pci_setup(blob, bd);
+#endif
+ ft_cpu_setup(blob, bd);
+
+ p = ft_get_prop(blob, "/memory/reg", &len);
+ if (p) {
+ *p++ = cpu_to_be32(bd->bi_memstart);
+ *p = cpu_to_be32(bd->bi_memsize);
+ }
+}
+#endif
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Authors: Nick.Spence@freescale.com
+ * Wilson.Lo@freescale.com
+ * scottwood@freescale.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+#ifndef CFG_8313ERDB_BROKEN_PMC
+static void resume_from_sleep(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ u32 magic = *(u32 *)0;
+
+ typedef void (*func_t)(void);
+ func_t resume = *(func_t *)4;
+
+ if (magic == 0xf5153ae5)
+ resume();
+
+ gd->flags &= ~GD_FLG_SILENT;
+ puts("\nResume from sleep failed: bad magic word\n");
+}
+#endif
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ volatile immap_t *im = (volatile immap_t *)CFG_IMMR;
+ u32 msize = CFG_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12;
+ im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
+ im->sysconf.ddrcdr = CFG_DDRCDR_VALUE;
+
+ /*
+ * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+ * or the DDR2 controller may fail to initialize correctly.
+ */
+ udelay(50000);
+
+ im->ddr.csbnds[0].csbnds = (msize - 1) >> 24;
+ im->ddr.cs_config[0] = CFG_DDR_CONFIG;
+
+ /* Currently we use only one CS, so disable the other bank. */
+ im->ddr.cs_config[1] = 0;
+
+ im->ddr.sdram_clk_cntl = CFG_DDR_CLK_CNTL;
+ im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3;
+ im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
+ im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
+ im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0;
+
+#ifndef CFG_8313ERDB_BROKEN_PMC
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ im->ddr.sdram_cfg = CFG_SDRAM_CFG | SDRAM_CFG_BI;
+ else
+#endif
+ im->ddr.sdram_cfg = CFG_SDRAM_CFG;
+
+ im->ddr.sdram_cfg2 = CFG_SDRAM_CFG2;
+ im->ddr.sdram_mode = CFG_DDR_MODE;
+ im->ddr.sdram_mode2 = CFG_DDR_MODE_2;
+
+ im->ddr.sdram_interval = CFG_DDR_INTERVAL;
+ sync();
+
+ /* enable DDR controller */
+ im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+
+ return msize;
+}
+
+long int initdram(int board_type)
+{
+ volatile immap_t *im = (volatile immap_t *)CFG_IMMR;
+ volatile lbus83xx_t *lbc = &im->lbus;
+ u32 msize;
+
+ if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ puts("Initializing\n");
+
+ /* DDR SDRAM - Main SODIMM */
+ msize = fixed_sdram();
+
+ /* Local Bus setup lbcr and mrtpr */
+ lbc->lbcr = CFG_LBC_LBCR;
+ lbc->mrtpr = CFG_LBC_MRTPR;
+ sync();
+
+#ifndef CFG_8313ERDB_BROKEN_PMC
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ resume_from_sleep();
+#endif
+
+ puts(" DDR RAM: ");
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
--- /dev/null
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/mpc83xx/start.o (.text)
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ . = ALIGN(16);
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x0FFF) & 0xFFFFF000;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(4096);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(4096);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+ _end = . ;
+ PROVIDE (end = .);
+}
+ENTRY(_start)
im->ddr.sdram_interval =
(0x0410 << SDRAM_INTERVAL_REFINT_SHIFT) | (0x0100 <<
SDRAM_INTERVAL_BSTOPRE_SHIFT);
- im->ddr.sdram_clk_cntl =
- DDR_SDRAM_CLK_CNTL_SS_EN | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05;
+ im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL;
udelay(200);
# Version: Xilinx EDK 6.3 EDK_Gmm.12.3
#
-TEXT_BASE = 0x12000000
+TEXT_BASE = 0x29000000
PLATFORM_CPPFLAGS += -mno-xl-soft-mul
PLATFORM_CPPFLAGS += -mno-xl-soft-div
#include <common.h>
#include <config.h>
+#include <asm/microblaze_intc.h>
+#include <asm/asm.h>
void do_reset (void)
{
int gpio_init (void)
{
#ifdef CFG_GPIO_0
- *((unsigned long *)(CFG_GPIO_0_ADDR)) = 0x0;
+ *((unsigned long *)(CFG_GPIO_0_ADDR)) = 0xFFFFFFFF;
#endif
return 0;
}
+
+#ifdef CFG_FSL_2
+void fsl_isr2 (void *arg) {
+ volatile int num;
+ *((unsigned int *)(CFG_GPIO_0_ADDR + 0x4)) =
+ ++(*((unsigned int *)(CFG_GPIO_0_ADDR + 0x4)));
+ GET (num, 2);
+ NGET (num, 2);
+ puts("*");
+}
+
+void fsl_init2 (void) {
+ puts("fsl_init2\n");
+ install_interrupt_handler (FSL_INTR_2,\
+ fsl_isr2,\
+ NULL);
+}
+#endif
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
- *
* CAUTION: This file is automatically generated by libgen.
- * Version: Xilinx EDK 6.3 EDK_Gmm.12.3
+ * Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4
*/
/* System Clock Frequency */
-#define XILINX_CLOCK_FREQ 66666667
+#define XILINX_CLOCK_FREQ 100000000
+
+/* Microblaze is microblaze_0 */
+#define XILINX_USE_MSR_INSTR 1
+#define XILINX_FSL_NUMBER 3
-/* Interrupt controller is intc_0 */
-#define XILINX_INTC_BASEADDR 0xd1000fc0
-#define XILINX_INTC_NUM_INTR_INPUTS 12
+/* Interrupt controller is opb_intc_0 */
+#define XILINX_INTC_BASEADDR 0x41200000
+#define XILINX_INTC_NUM_INTR_INPUTS 6
-/* Timer pheriphery is opb_timer_0 */
-#define XILINX_TIMER_BASEADDR 0xa2000000
+/* Timer pheriphery is opb_timer_1 */
+#define XILINX_TIMER_BASEADDR 0x41c00000
#define XILINX_TIMER_IRQ 0
-/* Uart pheriphery is console_uart */
-#define XILINX_UART_BASEADDR 0xa0000000
+/* Uart pheriphery is RS232_Uart */
+#define XILINX_UART_BASEADDR 0x40600000
#define XILINX_UART_BAUDRATE 115200
-/* GPIO is opb_gpio_0*/
-#define XILINX_GPIO_BASEADDR 0x90000000
+/* IIC pheriphery is IIC_EEPROM */
+#define XILINX_IIC_0_BASEADDR 0x40800000
+#define XILINX_IIC_0_FREQ 100000
+#define XILINX_IIC_0_BIT 0
+
+/* GPIO is LEDs_4Bit*/
+#define XILINX_GPIO_BASEADDR 0x40000000
-/* Flash Memory is opb_emc_0 */
-#define XILINX_FLASH_START 0x28000000
+/* Flash Memory is FLASH_2Mx32 */
+#define XILINX_FLASH_START 0x2c000000
#define XILINX_FLASH_SIZE 0x00800000
-/* Main Memory is plb_ddr_0 */
-#define XILINX_RAM_START 0x10000000
-#define XILINX_RAM_SIZE 0x10000000
+/* Main Memory is DDR_SDRAM_64Mx32 */
+#define XILINX_RAM_START 0x28000000
+#define XILINX_RAM_SIZE 0x04000000
-/* Sysace Controller is opb_sysace_0 */
-#define XILINX_SYSACE_BASEADDR 0xCF000000
-#define XILINX_SYSACE_HIGHADDR 0xCF0001FF
+/* Sysace Controller is SysACE_CompactFlash */
+#define XILINX_SYSACE_BASEADDR 0x41800000
+#define XILINX_SYSACE_HIGHADDR 0x4180ffff
#define XILINX_SYSACE_MEM_WIDTH 16
-/* Ethernet controller is opb_ethernet_0 */
+/* Ethernet controller is Ethernet_MAC */
#define XPAR_XEMAC_NUM_INSTANCES 1
#define XPAR_OPB_ETHERNET_0_DEVICE_ID 0
-#define XPAR_OPB_ETHERNET_0_BASEADDR 0x60000000
-#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x60003FFF
+#define XPAR_OPB_ETHERNET_0_BASEADDR 0x40c00000
+#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x40c0ffff
#define XPAR_OPB_ETHERNET_0_DMA_PRESENT 1
#define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST 1
#define XPAR_OPB_ETHERNET_0_MII_EXIST 1
memsize.o miiphybb.o miiphyutil.o \
s_record.o serial.o soft_i2c.o soft_spi.o spartan2.o spartan3.o \
usb.o usb_kbd.o usb_storage.o \
- virtex2.o xilinx.o crc16.o xyzModem.o cmd_mac.o
+ virtex2.o xilinx.o crc16.o xyzModem.o cmd_mac.o cmd_mfsl.o
SRCS := $(AOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(AOBJS) $(COBJS))
--- /dev/null
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Microblaze FSL support
+ */
+
+#include <common.h>
+#include <config.h>
+#include <command.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_MFSL)
+#include <asm/asm.h>
+
+int do_frd (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ unsigned int fslnum;
+ unsigned int num;
+ unsigned int blocking;
+
+ if (argc < 2) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ fslnum = (unsigned int)simple_strtoul (argv[1], NULL, 16);
+ blocking = (unsigned int)simple_strtoul (argv[2], NULL, 16);
+ if (fslnum < 0 || fslnum >= XILINX_FSL_NUMBER) {
+ puts ("Bad number of FSL\n");
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ switch (fslnum) {
+#if (XILINX_FSL_NUMBER > 0)
+ case 0:
+ switch (blocking) {
+ case 0: NGET (num, 0);
+ break;
+ case 1: NCGET (num, 0);
+ break;
+ case 2: GET (num, 0);
+ break;
+ case 3: CGET (num, 0);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 1)
+ case 1:
+ switch (blocking) {
+ case 0: NGET (num, 1);
+ break;
+ case 1: NCGET (num, 1);
+ break;
+ case 2: GET (num, 1);
+ break;
+ case 3: CGET (num, 1);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 2)
+ case 2:
+ switch (blocking) {
+ case 0: NGET (num, 2);
+ break;
+ case 1: NCGET (num, 2);
+ break;
+ case 2: GET (num, 2);
+ break;
+ case 3: CGET (num, 2);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 3)
+ case 3:
+ switch (blocking) {
+ case 0: NGET (num, 3);
+ break;
+ case 1: NCGET (num, 3);
+ break;
+ case 2: GET (num, 3);
+ break;
+ case 3: CGET (num, 3);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 4)
+ case 4:
+ switch (blocking) {
+ case 0: NGET (num, 4);
+ break;
+ case 1: NCGET (num, 4);
+ break;
+ case 2: GET (num, 4);
+ break;
+ case 3: CGET (num, 4);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 5)
+ case 5:
+ switch (blocking) {
+ case 0: NGET (num, 5);
+ break;
+ case 1: NCGET (num, 5);
+ break;
+ case 2: GET (num, 5);
+ break;
+ case 3: CGET (num, 5);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 6)
+ case 6:
+ switch (blocking) {
+ case 0: NGET (num, 6);
+ break;
+ case 1: NCGET (num, 6);
+ break;
+ case 2: GET (num, 6);
+ break;
+ case 3: CGET (num, 6);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 7)
+ case 7:
+ switch (blocking) {
+ case 0: NGET (num, 7);
+ break;
+ case 1: NCGET (num, 7);
+ break;
+ case 2: GET (num, 7);
+ break;
+ case 3: CGET (num, 7);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+ default:
+ return 1;
+ }
+
+ printf ("%01x: 0x%08lx - %s %s read\n", fslnum, num,
+ blocking < 2 ? "non blocking" : "blocking",
+ ((blocking == 1) || (blocking == 3)) ? "control" : "data" );
+ return 0;
+}
+
+int do_fwr (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ unsigned int fslnum;
+ unsigned int num;
+ unsigned int blocking;
+
+ if (argc < 3) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ fslnum = (unsigned int)simple_strtoul (argv[1], NULL, 16);
+ num = (unsigned int)simple_strtoul (argv[2], NULL, 16);
+ blocking = (unsigned int)simple_strtoul (argv[3], NULL, 16);
+ if (fslnum < 0 || fslnum >= XILINX_FSL_NUMBER) {
+ printf ("Bad number of FSL\nUsage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ switch (fslnum) {
+#if (XILINX_FSL_NUMBER > 0)
+ case 0:
+ switch (blocking) {
+ case 0: NPUT (num, 0);
+ break;
+ case 1: NCPUT (num, 0);
+ break;
+ case 2: PUT (num, 0);
+ break;
+ case 3: CPUT (num, 0);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 1)
+ case 1:
+ switch (blocking) {
+ case 0: NPUT (num, 1);
+ break;
+ case 1: NCPUT (num, 1);
+ break;
+ case 2: PUT (num, 1);
+ break;
+ case 3: CPUT (num, 1);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 2)
+ case 2:
+ switch (blocking) {
+ case 0: NPUT (num, 2);
+ break;
+ case 1: NCPUT (num, 2);
+ break;
+ case 2: PUT (num, 2);
+ break;
+ case 3: CPUT (num, 2);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 3)
+ case 3:
+ switch (blocking) {
+ case 0: NPUT (num, 3);
+ break;
+ case 1: NCPUT (num, 3);
+ break;
+ case 2: PUT (num, 3);
+ break;
+ case 3: CPUT (num, 3);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 4)
+ case 4:
+ switch (blocking) {
+ case 0: NPUT (num, 4);
+ break;
+ case 1: NCPUT (num, 4);
+ break;
+ case 2: PUT (num, 4);
+ break;
+ case 3: CPUT (num, 4);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 5)
+ case 5:
+ switch (blocking) {
+ case 0: NPUT (num, 5);
+ break;
+ case 1: NCPUT (num, 5);
+ break;
+ case 2: PUT (num, 5);
+ break;
+ case 3: CPUT (num, 5);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 6)
+ case 6:
+ switch (blocking) {
+ case 0: NPUT (num, 6);
+ break;
+ case 1: NCPUT (num, 6);
+ break;
+ case 2: PUT (num, 6);
+ break;
+ case 3: CPUT (num, 6);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+#if (XILINX_FSL_NUMBER > 7)
+ case 7:
+ switch (blocking) {
+ case 0: NPUT (num, 7);
+ break;
+ case 1: NCPUT (num, 7);
+ break;
+ case 2: PUT (num, 7);
+ break;
+ case 3: CPUT (num, 7);
+ break;
+ default:
+ return 2;
+ }
+ break;
+#endif
+ default:
+ return 1;
+ }
+
+ printf ("%01x: 0x%08lx - %s %s write\n", fslnum, num,
+ blocking < 2 ? "non blocking" : "blocking",
+ ((blocking == 1) || (blocking == 3)) ? "control" : "data" );
+ return 0;
+
+}
+
+int do_rspr (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ unsigned int reg = 0;
+ unsigned int val = 0;
+
+ reg = (unsigned int)simple_strtoul (argv[1], NULL, 16);
+ val = (unsigned int)simple_strtoul (argv[2], NULL, 16);
+ if (argc < 1) {
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+ switch (reg) {
+ case 0x1:
+ if (argc > 2) {
+ MTS (val, rmsr);
+ NOP;
+ MFS (val, rmsr);
+
+ } else {
+ MFS (val, rmsr);
+ }
+ puts ("MSR");
+ break;
+ case 0x3:
+ MFS (val, rear);
+ puts ("EAR");
+ break;
+ case 0x5:
+ MFS (val, resr);
+ puts ("ESR");
+ break;
+ default:
+ return 1;
+ }
+ printf (": 0x%08lx\n", val);
+ return 0;
+}
+
+/***************************************************/
+
+U_BOOT_CMD (frd, 3, 1, do_frd,
+ "frd - read data from FSL\n",
+ "- [fslnum [0|1|2|3]]\n"
+ " 0 - non blocking data read\n"
+ " 1 - non blocking control read\n"
+ " 2 - blocking data read\n"
+ " 3 - blocking control read\n");
+
+
+U_BOOT_CMD (fwr, 4, 1, do_fwr,
+ "fwr - write data to FSL\n",
+ "- [fslnum [0|1|2|3]]\n"
+ " 0 - non blocking data write\n"
+ " 1 - non blocking control write\n"
+ " 2 - blocking data write\n"
+ " 3 - blocking control write\n");
+
+U_BOOT_CMD (rspr, 3, 1, do_rspr,
+ "rmsr - read/write special purpose register\n",
+ "- reg_num [write value] read/write special purpose register\n"
+ " 0 - MSR - Machine status register\n"
+ " 1 - EAR - Exception address register\n"
+ " 2 - ESR - Exception status register\n");
+
+#endif /* CONFIG_MICROBLAZE & CFG_CMD_MFSL */
if (outputcnt)
*output = 0;
+ else
+ *(output - 1) = 0;
#ifdef DEBUG_PARSER
printf ("[PROCESS_MACROS] OUTPUT len %d: \"%s\"\n",
LIB = $(obj)lib$(CPU).a
START = start.o
-SOBJS = dcache.o icache.o irq.o disable_int.o enable_int.o
+SOBJS = irq.o
COBJS = cpu.o interrupts.o cache.o exception.o timer.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
*/
#include <common.h>
+#include <asm/asm.h>
#if (CONFIG_COMMANDS & CFG_CMD_CACHE)
__asm__ __volatile__ ("and %0,%0,%1"::"r" (i), "r" (mask):"memory");
return i;
}
+
+void icache_enable (void) {
+ MSRSET(0x20);
+}
+
+void icache_disable(void) {
+ MSRCLR(0x20);
+}
+
+void dcache_enable (void) {
+ MSRSET(0x80);
+}
+
+void dcache_disable(void) {
+ MSRCLR(0x80);
+}
#endif
+++ /dev/null
-/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal SIMEK <monstr@monstr.eu>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
- .text
- .globl dcache_enable
- .ent dcache_enable
- .align 2
-dcache_enable:
- /* Make space on stack for a temporary */
- addi r1, r1, -4
- /* Save register r12 */
- swi r12, r1, 0
- /* Read the MSR register */
- mfs r12, rmsr
- /* Set the instruction enable bit */
- ori r12, r12, 0x80
- /* Save the MSR register */
- mts rmsr, r12
- /* Load register r12 */
- lwi r12, r1, 0
- /* Return */
- rtsd r15, 8
- /* Update stack in the delay slot */
- addi r1, r1, 4
- .end dcache_enable
-
- .text
- .globl dcache_disable
- .ent dcache_disable
- .align 2
-dcache_disable:
- /* Make space on stack for a temporary */
- addi r1, r1, -4
- /* Save register r12 */
- swi r12, r1, 0
- /* Read the MSR register */
- mfs r12, rmsr
- /* Clear the data cache enable bit */
- andi r12, r12, ~0x80
- /* Save the MSR register */
- mts rmsr, r12
- /* Load register r12 */
- lwi r12, r1, 0
- /* Return */
- rtsd r15, 8
- /* Update stack in the delay slot */
- addi r1, r1, 4
- .end dcache_disable
+++ /dev/null
-/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal SIMEK <monstr@monstr.eu>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
- .text
- .globl microblaze_disable_interrupts
- .ent microblaze_disable_interrupts
- .align 2
-microblaze_disable_interrupts:
- #Make space on stack for a temporary
- addi r1, r1, -4
- #Save register r12
- swi r12, r1, 0
- #Read the MSR register
- mfs r12, rmsr
- #Clear the interrupt enable bit
- andi r12, r12, ~2
- #Save the MSR register
- mts rmsr, r12
- #Load register r12
- lwi r12, r1, 0
- #Return
- rtsd r15, 8
- #Update stack in the delay slot
- addi r1, r1, 4
- .end microblaze_disable_interrupts
+++ /dev/null
-/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal SIMEK <monstrmonstr.eu>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
- .text
- .globl microblaze_enable_interrupts
- .ent microblaze_enable_interrupts
- .align 2
-microblaze_enable_interrupts:
- addi r1, r1, -4
- swi r12, r1, 0
- mfs r12, rmsr
- ori r12, r12, 2
- mts rmsr, r12
- lwi r12, r1, 0
- rtsd r15, 8
- addi r1, r1, 4
- .end microblaze_enable_interrupts
*/
#include <common.h>
+#include <asm/asm.h>
void _hw_exception_handler (void)
{
int address = 0;
int state = 0;
/* loading address of exception EAR */
- __asm__ __volatile ("mfs %0,rear"::"r" (address):"memory");
+ MFS (address, rear);
/* loading excetpion state register ESR */
- __asm__ __volatile ("mfs %0,resr"::"r" (state):"memory");
+ MFS (state, resr);
printf ("Hardware exception at 0x%x address\n", address);
switch (state & 0x1f) { /* mask on exception cause */
case 0x1:
case 0x5:
puts ("Divide by zero exception\n");
break;
+#ifdef MICROBLAZE_V5
+ case 0x1000:
+ puts ("Exception in delay slot\n");
+ break;
+#endif
default:
puts ("Undefined cause\n");
break;
+++ /dev/null
-/*
- * (C) Copyright 2007 Michal Simek
- *
- * Michal SIMEK <monstr@monstr.eu>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
- .text
- .globl icache_enable
- .ent icache_enable
- .align 2
-icache_enable:
- /* Make space on stack for a temporary */
- addi r1, r1, -4
- /* Save register r12 */
- swi r12, r1, 0
- /* Read the MSR register */
- mfs r12, rmsr
- /* Set the instruction enable bit */
- ori r12, r12, 0x20
- /* Save the MSR register */
- mts rmsr, r12
- /* Load register r12 */
- lwi r12, r1, 0
- /* Return */
- rtsd r15, 8
- /* Update stack in the delay slot */
- addi r1, r1, 4
- .end icache_enable
-
- .text
- .globl icache_disable
- .ent icache_disable
- .align 2
-icache_disable:
- /* Make space on stack for a temporary */
- addi r1, r1, -4
- /* Save register r12 */
- swi r12, r1, 0
- /* Read the MSR register */
- mfs r12, rmsr
- /* Clear the instruction enable bit */
- andi r12, r12, ~0x20
- /* Save the MSR register */
- mts rmsr, r12
- /* Load register r12 */
- lwi r12, r1, 0
- /* Return */
- rtsd r15, 8
- /* Update stack in the delay slot */
- addi r1, r1, 4
- .end icache_disable
#include <common.h>
#include <command.h>
#include <asm/microblaze_intc.h>
+#include <asm/asm.h>
#undef DEBUG_INT
void enable_interrupts (void)
{
- microblaze_enable_interrupts ();
+ MSRSET(0x2);
}
int disable_interrupts (void)
{
- microblaze_disable_interrupts ();
+ MSRCLR(0x2);
return 0;
}
#ifdef CFG_TIMER_0
extern void timer_init (void);
#endif
+#ifdef CFG_FSL_2
+extern void fsl_init2 (void);
+#endif
+
static struct irq_action vecs[CFG_INTC_0_NUM];
act->count = 0;
enable_one_interrupt (irq);
} else { /* disable */
-
act->handler = (interrupt_handler_t *) def_hdlr;
act->arg = (void *)irq;
disable_one_interrupt (irq);
#ifdef CFG_TIMER_0
timer_init ();
#endif
+#ifdef CFG_FSL_2
+ fsl_init2 ();
+#endif
enable_interrupts ();
return 0;
}
void interrupt_handler (void)
{
- int irqs;
- irqs = (intc->isr & intc->ier); /* find active interrupt */
-
+ int irqs = (intc->isr & intc->ier); /* find active interrupt */
+ int i = 1;
#ifdef DEBUG_INT
+ int value;
printf ("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
intc->iar, intc->mer);
+ R14(value);
printf ("Interrupt handler on %x line, r14 %x\n", irqs, value);
#endif
struct irq_action *act = vecs;
#endif
act->handler (act->arg);
act->count++;
+ intc->iar = i;
+ return;
}
irqs >>= 1;
act++;
+ i <<= 1;
}
- intc->iar = 0xFFFFFFFF; /* erase all events */
-#ifdef DEBUG
+
+#ifdef DEBUG_INT
printf ("Dump INTC reg, isr %x, ier %x, iar %x, mer %x\n", intc->isr,
intc->ier, intc->iar, intc->mer);
- printf ("Interrupt handler on %x line, r14\n", irqs);
+ R14(value);
+ printf ("Interrupt handler on %x line, r14 %x\n", irqs, value);
#endif
}
#endif
*/
#include <config.h>
+#include <asm/asm.h>
.text
.global _interrupt_handler
_interrupt_handler:
addi r1, r1, 4
/* enable_interrupt */
+#ifdef XILINX_USE_MSR_INSTR
+ msrset r0, 2
+#else
+ /* FIXME unstable in stressed mode - two irqs */
+ nop
addi r1, r1, -4
swi r12, r1, 0
mfs r12, rmsr
lwi r12, r1, 0
addi r1, r1, 4
nop
+#endif
bra r14
nop
nop
3: /* jumping to board_init */
brai board_init
1: bri 1b
+
+/*
+ * Read 16bit little endian
+ */
+ .text
+ .global in16
+ .ent in16
+ .align 2
+in16: lhu r3, r0, r5
+ bslli r4, r3, 8
+ bsrli r3, r3, 8
+ andi r4, r4, 0xffff
+ or r3, r3, r4
+ rtsd r15, 8
+ sext16 r3, r3
+ .end in16
+
+/*
+ * Write 16bit little endian
+ * first parameter(r5) - address, second(r6) - short value
+ */
+ .text
+ .global out16
+ .ent out16
+ .align 2
+out16: bslli r3, r6, 8
+ bsrli r6, r6, 8
+ andi r3, r3, 0xffff
+ or r3, r3, r6
+ sh r3, r0, r5
+ rtsd r15, 8
+ or r0, r0, r0
+ .end out16
#include <common.h>
#include <asm/microblaze_timer.h>
+#include <asm/microblaze_intc.h>
volatile int timestamp = 0;
#ifdef CFG_INTC_0
#ifdef CFG_TIMER_0
-extern void install_interrupt_handler (int irq, interrupt_handler_t * hdlr,
- void *arg);
-
microblaze_timer_t *tmr = (microblaze_timer_t *) (CFG_TIMER_0_ADDR);
void timer_isr (void *arg)
*(vu_long *)(MPC5XXX_XLBARB + 0x40) |= (1 << 15);
*(vu_long *)(MPC5XXX_XLBARB + 0x70) = CFG_SDRAM_BASE | 0x1d;
-# if defined(CFG_IPBSPEED_133)
+# if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/* Motorola reports IPB should better run at 133 MHz. */
*(vu_long *)MPC5XXX_ADDECR |= 1;
/* pci_clk_sel = 0x02, ipb_clk_sel = 0x00; */
addecr = *(vu_long *)MPC5XXX_CDM_CFG;
addecr &= ~0x103;
-# if defined(CFG_PCISPEED_66)
+# if defined(CFG_PCICLK_EQUALS_IPBCLK_DIV2)
/* pci_clk_sel = 0x01 -> IPB_CLK/2 */
addecr |= 0x01;
# else
/* pci_clk_sel = 0x02 -> XLB_CLK/4 = IPB_CLK/4 */
addecr |= 0x02;
-# endif /* CFG_PCISPEED_66 */
+# endif /* CFG_PCICLK_EQUALS_IPBCLK_DIV2 */
*(vu_long *)MPC5XXX_CDM_CFG = addecr;
-# endif /* CFG_IPBSPEED_133 */
+# endif /* CFG_IPBCLK_EQUALS_XLBCLK */
/* Configure the XLB Arbiter */
*(vu_long *)MPC5XXX_XLBARB_MPRIEN = 0xff;
*(vu_long *)MPC5XXX_XLBARB_MPRIVAL = 0x11111111;
*/
fec->eth->imask = 0x00000000;
+/*
+ * In original Promess-provided code PHY initialization is disabled with the
+ * following comment: "Phy initialization is DISABLED for now. There was a
+ * problem with running 100 Mbps on PRO board". Thus we temporarily disable
+ * PHY initialization for the Motion-PRO board, until a proper fix is found.
+ */
+
if (fec->xcv_type != SEVENWIRE) {
/*
* Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
START = start.o
COBJS = traps.o cpu.o cpu_init.o speed.o interrupts.o \
- spd_sdram.o qe_io.o
+ spd_sdram.o qe_io.o pci.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
immr = (immap_t *)CFG_IMMR;
- if ((pvr & 0xFFFF0000) != PVR_83xx) {
- puts("Not MPC83xx Family!!!\n");
- return -1;
+ puts("CPU: ");
+
+ switch (pvr & 0xffff0000) {
+ case PVR_E300C1:
+ printf("e300c1, ");
+ break;
+
+ case PVR_E300C2:
+ printf("e300c2, ");
+ break;
+
+ case PVR_E300C3:
+ printf("e300c3, ");
+ break;
+
+ default:
+ printf("Unknown core, ");
}
spridr = immr->sysconf.spridr;
- puts("CPU: ");
switch(spridr) {
case SPR_8349E_REV10:
case SPR_8349E_REV11:
case SPR_8321_REV11:
puts("MPC8321, ");
break;
+ case SPR_8311_REV10:
+ puts("MPC8311, ");
+ break;
+ case SPR_8311E_REV10:
+ puts("MPC8311E, ");
+ break;
+ case SPR_8313_REV10:
+ puts("MPC8313, ");
+ break;
+ case SPR_8313E_REV10:
+ puts("MPC8313E, ");
+ break;
default:
puts("Rev: Unknown revision number.\nWarning: Unsupported cpu revision!\n");
return 0;
/* Multiple revisons of 834x processors may have the same SPRIDR value.
* So use PVR to identify the revision number.
*/
- printf("Rev: %02x at %s MHz\n", PVR_MAJ(pvr)<<4 | PVR_MIN(pvr), strmhz(buf, clock));
+ printf("Rev: %02x at %s MHz", PVR_MAJ(pvr)<<4 | PVR_MIN(pvr), strmhz(buf, clock));
#else
- printf("Rev: %02x at %s MHz\n", spridr & 0x0000FFFF, strmhz(buf, clock));
+ printf("Rev: %02x at %s MHz", spridr & 0x0000FFFF, strmhz(buf, clock));
#endif
+ printf(", CSB: %4d MHz\n", gd->csb_clk / 1000000);
+
return 0;
}
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2007
+ *
+ * Author: Scott Wood <scottwood@freescale.com>,
+ * with some bits from older board-specific PCI initialization.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <ft_build.h>
+#include <asm/mpc8349_pci.h>
+
+#ifdef CONFIG_83XX_GENERIC_PCI
+#define MAX_BUSES 2
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct pci_controller pci_hose[MAX_BUSES];
+static int pci_num_buses;
+
+static void pci_init_bus(int bus, struct pci_region *reg)
+{
+ volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+ volatile pot83xx_t *pot = immr->ios.pot;
+ volatile pcictrl83xx_t *pci_ctrl = &immr->pci_ctrl[bus];
+ struct pci_controller *hose = &pci_hose[bus];
+ u32 dev;
+ u16 reg16;
+ int i;
+
+ if (bus == 1)
+ pot += 3;
+
+ /* Setup outbound translation windows */
+ for (i = 0; i < 3; i++, reg++, pot++) {
+ if (reg->size == 0)
+ break;
+
+ hose->regions[i] = *reg;
+ hose->region_count++;
+
+ pot->potar = reg->bus_start >> 12;
+ pot->pobar = reg->phys_start >> 12;
+ pot->pocmr = ~(reg->size - 1) >> 12;
+
+ if (reg->flags & PCI_REGION_IO)
+ pot->pocmr |= POCMR_IO;
+#ifdef CONFIG_83XX_PCI_STREAMING
+ else if (reg->flags & PCI_REGION_PREFETCH)
+ pot->pocmr |= POCMR_SE;
+#endif
+
+ if (bus == 1)
+ pot->pocmr |= POCMR_DST;
+
+ pot->pocmr |= POCMR_EN;
+ }
+
+ /* Point inbound translation at RAM */
+ pci_ctrl->pitar1 = 0;
+ pci_ctrl->pibar1 = 0;
+ pci_ctrl->piebar1 = 0;
+ pci_ctrl->piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP |
+ PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
+
+ i = hose->region_count++;
+ hose->regions[i].bus_start = 0;
+ hose->regions[i].phys_start = 0;
+ hose->regions[i].size = gd->ram_size;
+ hose->regions[i].flags = PCI_REGION_MEM | PCI_REGION_MEMORY;
+
+ hose->first_busno = 0;
+ hose->last_busno = 0xff;
+
+ pci_setup_indirect(hose, CFG_IMMR + 0x8300 + bus * 0x80,
+ CFG_IMMR + 0x8304 + bus * 0x80);
+
+ pci_register_hose(hose);
+
+ /*
+ * Write to Command register
+ */
+ reg16 = 0xff;
+ dev = PCI_BDF(hose->first_busno, 0, 0);
+ pci_hose_read_config_word(hose, dev, PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
+ pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
+ pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
+
+#ifdef CONFIG_PCI_SCAN_SHOW
+ printf("PCI: Bus Dev VenId DevId Class Int\n");
+#endif
+ /*
+ * Hose scan.
+ */
+ hose->last_busno = pci_hose_scan(hose);
+}
+
+/*
+ * The caller must have already set OCCR, and the PCI_LAW BARs
+ * must have been set to cover all of the requested regions.
+ *
+ * If fewer than three regions are requested, then the region
+ * list is terminated with a region of size 0.
+ */
+void mpc83xx_pci_init(int num_buses, struct pci_region **reg, int warmboot)
+{
+ volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+ int i;
+
+ if (num_buses > MAX_BUSES) {
+ printf("%d PCI buses requsted, %d supported\n",
+ num_buses, MAX_BUSES);
+
+ num_buses = MAX_BUSES;
+ }
+
+ pci_num_buses = num_buses;
+
+ /*
+ * Release PCI RST Output signal.
+ * Power on to RST high must be at least 100 ms as per PCI spec.
+ * On warm boots only 1 ms is required.
+ */
+ udelay(warmboot ? 1000 : 100000);
+
+ for (i = 0; i < num_buses; i++)
+ immr->pci_ctrl[i].gcr = 1;
+
+ /*
+ * RST high to first config access must be at least 2^25 cycles
+ * as per PCI spec. This could be cut in half if we know we're
+ * running at 66MHz. This could be insufficiently long if we're
+ * running the PCI bus at significantly less than 33MHz.
+ */
+ udelay(1020000);
+
+ for (i = 0; i < num_buses; i++)
+ pci_init_bus(i, reg[i]);
+}
+
+#ifdef CONFIG_OF_FLAT_TREE
+void ft_pci_setup(void *blob, bd_t *bd)
+{
+ u32 *p;
+ int len;
+
+ if (pci_num_buses < 1)
+ return;
+
+ p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8500/bus-range", &len);
+ if (p) {
+ p[0] = pci_hose[0].first_busno;
+ p[1] = pci_hose[0].last_busno;
+ }
+
+ if (pci_num_buses < 2)
+ return;
+
+ p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8600/bus-range", &len);
+ if (p) {
+ p[0] = pci_hose[1].first_busno;
+ p[1] = pci_hose[1].last_busno;
+ }
+}
+#endif /* CONFIG_OF_FLAT_TREE */
+
+#endif /* CONFIG_83XX_GENERIC_PCI */
int clks;
ddr_bus_clk = gd->ddr_clk >> 1;
- clks = picos / ((1000000000 / ddr_bus_clk) * 1000);
- if (picos % ((1000000000 / ddr_bus_clk) * 1000) != 0)
+ clks = picos / (1000000000 / (ddr_bus_clk / 1000));
+ if (picos % (1000000000 / (ddr_bus_clk / 1000)) != 0)
clks++;
return clks;
| (1 << (16 + 10)) /* DQS Differential disable */
| (add_lat << (16 + 3)) /* Additive Latency in EMRS1 */
| (mode_odt_enable << 16) /* ODT Enable in EMRS1 */
- | ((twr_clk >> 1) << 9) /* Write Recovery Autopre */
+ | ((twr_clk - 1) << 9) /* Write Recovery Autopre */
| (caslat << 4) /* caslat */
| (burstlen << 0) /* Burst length */
);
#ifdef CFG_DDR_SDRAM_CLK_CNTL /* Optional platform specific value */
ddr->sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL;
-#else
- /* SS_EN = 0, source synchronous disable
- * CLK_ADJST = 0, MCK/MCK# is launched aligned with addr/cmd
- */
- ddr->sdram_clk_cntl = 0x00000000;
#endif
debug("DDR:sdram_clk_cntl=0x%08x\n", ddr->sdram_clk_cntl);
#include <common.h>
#include <mpc83xx.h>
+#include <command.h>
#include <asm/processor.h>
DECLARE_GLOBAL_DATA_PTR;
u32 lcrr;
u32 csb_clk;
-#if defined(CONFIG_MPC834X)
+#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X)
u32 tsec1_clk;
u32 tsec2_clk;
- u32 usbmph_clk;
u32 usbdr_clk;
#endif
+#ifdef CONFIG_MPC834X
+ u32 usbmph_clk;
+#endif
u32 core_clk;
u32 i2c1_clk;
#if !defined(CONFIG_MPC832X)
sccr = im->clk.sccr;
-#if defined(CONFIG_MPC834X)
+#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X)
switch ((sccr & SCCR_TSEC1CM) >> SCCR_TSEC1CM_SHIFT) {
case 0:
tsec1_clk = 0;
return -4;
}
+ switch ((sccr & SCCR_USBDRCM) >> SCCR_USBDRCM_SHIFT) {
+ case 0:
+ usbdr_clk = 0;
+ break;
+ case 1:
+ usbdr_clk = csb_clk;
+ break;
+ case 2:
+ usbdr_clk = csb_clk / 2;
+ break;
+ case 3:
+ usbdr_clk = csb_clk / 3;
+ break;
+ default:
+ /* unkown SCCR_USBDRCM value */
+ return -8;
+ }
+#endif
+
+#if defined(CONFIG_MPC834X)
switch ((sccr & SCCR_TSEC2CM) >> SCCR_TSEC2CM_SHIFT) {
case 0:
tsec2_clk = 0;
return -7;
}
- switch ((sccr & SCCR_USBDRCM) >> SCCR_USBDRCM_SHIFT) {
- case 0:
- usbdr_clk = 0;
- break;
- case 1:
- usbdr_clk = csb_clk;
- break;
- case 2:
- usbdr_clk = csb_clk / 2;
- break;
- case 3:
- usbdr_clk = csb_clk / 3;
- break;
- default:
- /* unkown SCCR_USBDRCM value */
- return -8;
- }
-
if (usbmph_clk != 0 && usbdr_clk != 0 && usbmph_clk != usbdr_clk) {
/* if USB MPH clock is not disabled and
* USB DR clock is not disabled then
*/
return -9;
}
+#elif defined(CONFIG_MPC831X)
+ tsec2_clk = tsec1_clk;
+
+ if (!(sccr & SCCR_TSEC1ON))
+ tsec1_clk = 0;
+ if (!(sccr & SCCR_TSEC2ON))
+ tsec2_clk = 0;
#endif
-#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X)
+
+#if !defined(CONFIG_MPC834X)
i2c1_clk = csb_clk;
#endif
#if !defined(CONFIG_MPC832X)
#endif
gd->csb_clk = csb_clk;
-#if defined(CONFIG_MPC834X)
+#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X)
gd->tsec1_clk = tsec1_clk;
gd->tsec2_clk = tsec2_clk;
- gd->usbmph_clk = usbmph_clk;
gd->usbdr_clk = usbdr_clk;
#endif
+#if defined(CONFIG_MPC834X)
+ gd->usbmph_clk = usbmph_clk;
+#endif
gd->core_clk = core_clk;
gd->i2c1_clk = i2c1_clk;
#if !defined(CONFIG_MPC832X)
return gd->csb_clk;
}
-int print_clock_conf(void)
+int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
printf("Clock configuration:\n");
- printf(" Coherent System Bus: %4d MHz\n", gd->csb_clk / 1000000);
printf(" Core: %4d MHz\n", gd->core_clk / 1000000);
+ printf(" Coherent System Bus: %4d MHz\n", gd->csb_clk / 1000000);
#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X)
printf(" QE: %4d MHz\n", gd->qe_clk / 1000000);
printf(" BRG: %4d MHz\n", gd->brg_clk / 1000000);
#if !defined(CONFIG_MPC832X)
printf(" I2C2: %4d MHz\n", gd->i2c2_clk / 1000000);
#endif
-#if defined(CONFIG_MPC834X)
+#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X)
printf(" TSEC1: %4d MHz\n", gd->tsec1_clk / 1000000);
printf(" TSEC2: %4d MHz\n", gd->tsec2_clk / 1000000);
- printf(" USB MPH: %4d MHz\n", gd->usbmph_clk / 1000000);
printf(" USB DR: %4d MHz\n", gd->usbdr_clk / 1000000);
#endif
+#if defined(CONFIG_MPC834X)
+ printf(" USB MPH: %4d MHz\n", gd->usbmph_clk / 1000000);
+#endif
return 0;
}
+
+U_BOOT_CMD(clocks, 1, 0, do_clocks,
+ "clocks - print clock configuration\n",
+ " clocks\n"
+);
#if (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined(CFG_NAND_LEGACY) && \
(defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX))
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
+ defined(CONFIG_405EZ))
#include <nand.h>
#include <linux/mtd/ndfc.h>
#include <asm/processor.h>
-#include <ppc440.h>
+#include <ppc4xx.h>
static u8 hwctl = 0;
/*
* Setup EBC (CS0 only right now)
*/
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xb8400000);
+ mtebc(EBC0_CFG, 0xb8400000);
mtebc(pb0cr, CFG_EBC_PB0CR);
mtebc(pb0ap, CFG_EBC_PB0AP);
mtdcr ocmdscr2, r3 /* Set Data Side */
mtdcr ocmiscr2, r3 /* Set Instruction Side */
addis r3,0,0x0800 /* OCM Data Parity Disable - 1 Wait State */
- mtdcr ocmdsisdpc,r4
+ mtdcr ocmdsisdpc,r3
isync
#else /* CONFIG_405EZ */
--- /dev/null
+Freescale MPC8313ERDB Board
+-----------------------------------------
+
+1. Board Switches and Jumpers
+
+ SW3 is used to set CFG_RESET_SOURCE.
+
+ To boot the image at 0xFE000000 in NOR flash, use these DIP
+ switche settings for SW3 SW4:
+
+ +------+ +------+
+ | | | **** |
+ | **** | | |
+ +------+ ON +------+ ON
+ 4321 4321
+ (where the '*' indicates the position of the tab of the switch.)
+
+2. Memory Map
+ The memory map looks like this:
+
+ 0x0000_0000 0x07ff_ffff DDR 128M
+ 0x8000_0000 0x8fff_ffff PCI MEM 256M
+ 0x9000_0000 0x9fff_ffff PCI_MMIO 256M
+ 0xe000_0000 0xe00f_ffff IMMR 1M
+ 0xe200_0000 0xe20f_ffff PCI IO 16M
+ 0xe280_0000 0xe280_7fff NAND FLASH (CS1) 32K
+ 0xf000_0000 0xf001_ffff VSC7385 (CS2) 128K
+ 0xfa00_0000 0xfa00_7fff Board Status/ 32K
+ LED Control (CS3)
+ 0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M
+
+3. Definitions
+
+3.1 Explanation of NEW definitions in:
+
+ include/configs/MPC8313ERDB.h
+
+ CONFIG_MPC83xx MPC83xx family
+ CONFIG_MPC831x MPC831x specific
+ CONFIG_MPC8313ERDB MPC8313ERDB board specific
+
+4. Compilation
+
+ Assuming you're using BASH (or similar) as your shell:
+
+ export CROSS_COMPILE=your-cross-compiler-prefix-
+ make distclean
+ make MPC8313ERDB_33_config
+ (or make MPC8313ERDB_66_config, depending on the speed of
+ the oscillator on your board)
+ make
+
+5. Downloading and Flashing Images
+
+5.1 Reflash U-boot Image using U-boot
+
+ =>run tftpflash
+
+ You may want to try
+ =>tftpboot $loadaddr $uboot
+ first, to make sure that the TFTP load will succeed before it
+ goes ahead and wipes out your current firmware. And of course,
+ have an alternate means of programming the flash available
+ if the new u-boot doesn't boot.
+
+5.2 Downloading and Booting Linux Kernel
+
+ Ensure that all networking-related environment variables are set
+ properly (including ipaddr, serverip, gatewayip (if needed),
+ netmask, ethaddr, eth1addr, rootpath (if using NFS root),
+ fdtfile, and bootfile).
+
+ Then, do one of the following, depending on whether you
+ want an NFS root or a ramdisk root:
+
+ =>run nfsboot
+ or
+ =>run ramboot
+
+6 Notes
+
+ Booting from NAND flash is not yet supported.
+ The console baudrate for MPC8313ERDB is 115200bps.
+++ /dev/null
-The port was tested on Wind River System Sbc8560 board <www.windriver.com>.
-U-Boot was installed on the flash memory of the CPU card (no the SODIMM).
-
-NOTE: Please configure uboot compile to the proper PCI frequency and
-setup the appropriate DIP switch settings.
-
-SBC8560 board:
-
-Make sure boards switches are set to their appropriate conditions.
-Refer to the Engineering Reference Guide ERG-00300-002. Of particular
-importance are: 1)Tthe settings for JP4 (JP4 1-3 and 2-4), which
-select the on-board FLASH device (Intel 28F128Jx); 2) The settings
-for the Clock SW9 (33 MHz or 66 MHz).
-
- Note: SW9 Settings: 66 MHz
- 4:1 ratio CCB clocks:SYSCLK
- 3:1 ration e500 Core:CCB
- pos1 - on, pos2 - on, pos3 - off, pos4 - on, pos5 - off, pos6 - on
- Note: SW9 Settings: 33 MHz
- 8:1 ratio CCB clocks:SYSCLK
- 3:1 ration e500 Core:CCB
- pos1 - on, pos2 - on, pos3 - on, pos4 - off, pos5 - off, pos6 - on
-
-
-Flashing the FLASH device with the "Wind River ICE":
-
-1) Properly connect and configure the Wind River ICE to the
- target JTAG port. This includes running the SBC8560 register script.
- Make sure target memory can be read and written.
-
-2) Build the u-boot image:
- make distclean
- make SBC8560_66_config or SBC8560_33_config
- make CROSS_COMPILE=.../ELDK3.0/ppc_8xx-/ all
-
- Note: reference is made to the ELDK3.0 compiler but any 85xx cross-compiler
- should suffice.
-
-3) Convert the uboot (.elf) file to a uboot.bin file (using visionClick converter).
- The bin file should be converted from fffc0000 to ffffffff
-
-4) Setup the Flash Utility (tools menu) for:
-
- Determine the clock speed of the PCI bus and set SW9 accordingly
- Note: the speed of the PCI bus defaults to the slowest PCI card
- PlayBack the "default" register file for the SBC8560
- Select the uboot.bin file with zero bias
- Select the initialize Target prior to programming
- Select the V28F640Jx (8192 x 8) 1 device FLASH Algorithm
- Select the erase base address from FFFC0000 to FFFFFFFF
- Select the start address from 0 with size of 4000
-
-5) Erase and Program
/* Write sector count | ReadMemCardData. */
ace_writew((trans & 0xff) | 0x0300, 0x14);
+/*
+ * For FPGA configuration via SystemACE is reset unacceptable
+ * CFGDONE bit in STATUSREG is not set to 1.
+ */
+#ifndef SYSTEMACE_CONFIG_FPGA
/* Reset the configruation controller */
val = ace_readw(0x18);
val |= 0x0080;
ace_writew(val, 0x18);
+#endif
retry = trans * 16;
while (retry > 0) {
long zlib_decompress(unsigned char *data_in, unsigned char *cpage_out,
__u32 srclen, __u32 destlen)
{
- return (decompress_block(cpage_out, data_in + 2, ldr_memcpy));
+ return (decompress_block(cpage_out, data_in + 2, (void *) ldr_memcpy));
}
--- /dev/null
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* FSL macros */
+#define NGET(val, fslnum) \
+ __asm__ __volatile__ ("nget %0, rfsl" #fslnum :"=r" (val));
+
+#define GET(val, fslnum) \
+ __asm__ __volatile__ ("get %0, rfsl" #fslnum :"=r" (val));
+
+#define NCGET(val, fslnum) \
+ __asm__ __volatile__ ("ncget %0, rfsl" #fslnum :"=r" (val));
+
+#define CGET(val, fslnum) \
+ __asm__ __volatile__ ("cget %0, rfsl" #fslnum :"=r" (val));
+
+#define NPUT(val, fslnum) \
+ __asm__ __volatile__ ("nput %0, rfsl" #fslnum ::"r" (val));
+
+#define PUT(val, fslnum) \
+ __asm__ __volatile__ ("put %0, rfsl" #fslnum ::"r" (val));
+
+#define NCPUT(val, fslnum) \
+ __asm__ __volatile__ ("ncput %0, rfsl" #fslnum ::"r" (val));
+
+#define CPUT(val, fslnum) \
+ __asm__ __volatile__ ("cput %0, rfsl" #fslnum ::"r" (val));
+
+/* CPU dependent */
+/* machine status register */
+#define MFS(val, reg) \
+ __asm__ __volatile__ ("mfs %0," #reg :"=r" (val));
+
+#define MTS(val, reg) \
+ __asm__ __volatile__ ("mts " #reg ", %0"::"r" (val));
+
+/* get return address from interrupt */
+#define R14(val) \
+ __asm__ __volatile__ ("addi %0, r14, 0":"=r" (val));
+
+#define NOP __asm__ __volatile__ ("nop");
+
+/* use machine status registe USE_MSR_REG */
+#ifdef XILINX_USE_MSR_INSTR
+#define MSRSET(val) \
+ __asm__ __volatile__ ("msrset r0," #val );
+
+#define MSRCLR(val) \
+ __asm__ __volatile__ ("msrclr r0," #val );
+
+#else
+#define MSRSET(val) \
+{ \
+ register unsigned tmp; \
+ __asm__ __volatile__ (" \
+ mfs %0, rmsr; \
+ ori %0, %0, "#val"; \
+ mts rmsr, %0; \
+ nop;" \
+ : "=r" (tmp) \
+ : "d" (val) \
+ : "memory"); \
+}
+
+#define MSRCLR(val) \
+{ \
+ register unsigned tmp; \
+ __asm__ __volatile__ (" \
+ mfs %0, rmsr; \
+ andi %0, %0, ~"#val"; \
+ mts rmsr, %0; \
+ nop;" \
+ : "=r" (tmp) \
+ : "d" (val) \
+ : "memory"); \
+}
+#endif
void *arg;
int count; /* number of interrupt */
};
+
+void install_interrupt_handler (int irq, interrupt_handler_t * hdlr,
+ void *arg);
#ifndef __E300_H__
#define __E300_H__
-/*
- * e300 Processor Version & Revision Numbers
- */
-#define PVR_83xx 0x80830000
-#define PVR_8349_REV10 (PVR_83xx | 0x0010)
-#define PVR_8349_REV11 (PVR_83xx | 0x0011)
-#define PVR_8360_REV10 (PVR_83xx | 0x0020)
-#define PVR_8360_REV11 (PVR_83xx | 0x0020)
-
-#if defined(CONFIG_MPC832X)
-#undef PVR_83xx
-#define PVR_83xx 0x80840000
-#endif
+#define PVR_E300C1 0x80830000
+#define PVR_E300C2 0x80840000
+#define PVR_E300C3 0x80850000
/*
* Hardware Implementation-Dependent Register 0 (HID0)
#if defined(CONFIG_MPC83XX)
/* There are other clocks in the MPC83XX */
u32 csb_clk;
-#if defined (CONFIG_MPC834X)
+#if defined (CONFIG_MPC834X) || defined(CONFIG_MPC831X)
u32 tsec1_clk;
u32 tsec2_clk;
- u32 usbmph_clk;
u32 usbdr_clk;
+#endif
+#if defined (CONFIG_MPC834X)
+ u32 usbmph_clk;
#endif /* CONFIG_MPC834X */
u32 core_clk;
u32 i2c1_clk;
u32 pmccr; /* PMC Configuration Register */
u32 pmcer; /* PMC Event Register */
u32 pmcmr; /* PMC Mask Register */
- u8 res0[0xF4];
+ u32 pmccr1; /* PMC Configuration Register 1 */
+ u32 pmccr2; /* PMC Configuration Register 2 */
+ u8 res0[0xEC];
} pmc83xx_t;
/*
u8 res2[0x8];
u32 mrtpr; /* Memory Refresh Timer Prescaler Register */
u32 mdr; /* UPM Data Register */
- u8 res3[0x8];
+ u8 res3[0x4];
+ u32 lsor; /* Special Operation Initiation Register */
u32 lsdmr; /* SDRAM Mode Register */
u8 res4[0x8];
u32 lurt; /* UPM Refresh Timer */
u8 res6[0xC];
u32 lbcr; /* Configuration Register */
u32 lcrr; /* Clock Ratio Register */
- u8 res7[0x28];
- u8 res8[0xF00];
+ u8 res7[0x8];
+ u32 fmr; /* Flash Mode Register */
+ u32 fir; /* Flash Instruction Register */
+ u32 fcr; /* Flash Command Register */
+ u32 fbar; /* Flash Block Addr Register */
+ u32 fpar; /* Flash Page Addr Register */
+ u32 fbcr; /* Flash Byte Count Register */
+ u8 res8[0xF08];
} lbus83xx_t;
/*
* USB
*/
typedef struct usb83xx {
- u8 fixme[0x2000];
+ u8 fixme[0x1000];
} usb83xx_t;
/*
ios83xx_t ios; /* Sequencer */
pcictrl83xx_t pci_ctrl[2]; /* PCI Controller Control and Status Registers */
u8 res5[0x19900];
- usb83xx_t usb;
+ usb83xx_t usb[2];
+ tsec83xx_t tsec[2];
+ u8 res6[0xA000];
+ security83xx_t security;
+ u8 res7[0xC0000];
+} immap_t;
+
+#elif defined(CONFIG_MPC831X)
+typedef struct immap {
+ sysconf83xx_t sysconf; /* System configuration */
+ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */
+ rtclk83xx_t rtc; /* Real Time Clock Module Registers */
+ rtclk83xx_t pit; /* Periodic Interval Timer */
+ gtm83xx_t gtm[2]; /* Global Timers Module */
+ ipic83xx_t ipic; /* Integrated Programmable Interrupt Controller */
+ arbiter83xx_t arbiter; /* System Arbiter Registers */
+ reset83xx_t reset; /* Reset Module */
+ clk83xx_t clk; /* System Clock Module */
+ pmc83xx_t pmc; /* Power Management Control Module */
+ gpio83xx_t gpio[1]; /* General purpose I/O module */
+ u8 res0[0x1300];
+ ddr83xx_t ddr; /* DDR Memory Controller Memory */
+ fsl_i2c_t i2c[2]; /* I2C Controllers */
+ u8 res1[0x1300];
+ duart83xx_t duart[2]; /* DUART */
+ u8 res2[0x900];
+ lbus83xx_t lbus; /* Local Bus Controller Registers */
+ u8 res3[0x1000];
+ spi83xx_t spi; /* Serial Peripheral Interface */
+ dma83xx_t dma; /* DMA */
+ pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */
+ u8 res4[0x80];
+ ios83xx_t ios; /* Sequencer */
+ pcictrl83xx_t pci_ctrl[1]; /* PCI Controller Control and Status Registers */
+ u8 res5[0x1aa00];
+ usb83xx_t usb[1];
tsec83xx_t tsec[2];
u8 res6[0xA000];
security83xx_t security;
#define CFG_CMD_EXT2 0x1000000000000000ULL /* EXT2 Support */
#define CFG_CMD_SNTP 0x2000000000000000ULL /* SNTP support */
#define CFG_CMD_DISPLAY 0x4000000000000000ULL /* Display support */
+#define CFG_CMD_MFSL 0x8000000000000000ULL /* FSL support for Microblaze */
#define CFG_CMD_ALL 0xFFFFFFFFFFFFFFFFULL /* ALL commands */
CFG_CMD_IRQ | \
CFG_CMD_JFFS2 | \
CFG_CMD_KGDB | \
+ CFG_CMD_MFSL | \
CFG_CMD_MII | \
CFG_CMD_MMC | \
CFG_CMD_NAND | \
void ppcSync(void);
void ppcDcbz(unsigned long value);
#endif
+#if defined (CONFIG_MICROBLAZE)
+unsigned short in16(unsigned int);
+void out16(unsigned int, unsigned short value);
+#endif
#if defined (CONFIG_MPC83XX)
void ppcDWload(unsigned int *addr, unsigned int *ret);
int adjust_sdram_tbs_8xx (void);
#if defined(CONFIG_8260)
int prt_8260_clks (void);
-#elif defined(CONFIG_MPC83XX)
-int print_clock_conf(void);
#elif defined(CONFIG_MPC5xxx)
int prt_mpc5xxx_clks (void);
#endif
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet
- * hasn't been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#if defined(CFG_IPBSPEED_133)
-# define CFG_PCISPEED_66 /* define for 66MHz speed */
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
+# define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
# define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
# define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
* IPB Bus clocking configuration.
*/
#if defined(CONFIG_LITE5200B)
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#else
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
#endif /* CONFIG_MPC5200 */
--- /dev/null
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * mpc8313epb board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1
+#define CONFIG_MPC83XX 1
+#define CONFIG_MPC831X 1
+#define CONFIG_MPC8313 1
+#define CONFIG_MPC8313ERDB 1
+
+#define CONFIG_PCI
+#define CONFIG_83XX_GENERIC_PCI
+
+#ifdef CFG_66MHZ
+#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
+#elif defined(CFG_33MHZ)
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#else
+#error Unknown oscillator frequency.
+#endif
+
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+
+#define CFG_IMMR 0xE0000000
+
+#define CFG_MEMTEST_START 0x00001000
+#define CFG_MEMTEST_END 0x07f00000
+
+/* Early revs of this board will lock up hard when attempting
+ * to access the PMC registers, unless a JTAG debugger is
+ * connected, or some resistor modifications are made.
+ */
+#define CFG_8313ERDB_BROKEN_PMC 1
+
+#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+
+/*
+ * Manually set up DDR parameters, as this board does not
+ * seem to have the SPD connected to I2C.
+ */
+#define CFG_DDR_SIZE 128 /* MB */
+#define CFG_DDR_CONFIG ( CSCONFIG_EN | CSCONFIG_AP \
+ | 0x00040000 /* TODO */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
+ /* 0x80840102 */
+
+#define CFG_DDR_TIMING_3 0x00000000
+#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WRT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_RRT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WWT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
+ | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
+ /* 0x00220802 */
+#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
+ | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+ | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
+ | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
+ | (13 << TIMING_CFG1_REFREC_SHIFT ) \
+ | ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
+ | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
+ | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
+ /* 0x3935d322 */
+#define CFG_DDR_TIMING_2 ( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+ | (31 << TIMING_CFG2_CPO_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
+ | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
+ | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
+ | (10 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+ /* 0x0f9048ca */ /* P9-45,may need tuning */
+#define CFG_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+ | ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+ /* 0x03200064 */
+#if defined(CONFIG_DDR_2T_TIMING)
+#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
+ | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+ | SDRAM_CFG_2T_EN \
+ | SDRAM_CFG_DBW_32 )
+#else
+#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
+ | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+ | SDRAM_CFG_32_BE )
+ /* 0x43080000 */
+#endif
+#define CFG_SDRAM_CFG2 0x00401000;
+/* set burst length to 8 for 32-bit data path */
+#define CFG_DDR_MODE ( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
+ | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
+ /* 0x44400232 */
+#define CFG_DDR_MODE_2 0x8000C000;
+
+#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+ /*0x02000000*/
+#define CFG_DDRCDR_VALUE ( DDRCDR_EN \
+ | DDRCDR_PZ_NOMZ \
+ | DDRCDR_NZ_NOMZ \
+ | DDRCDR_M_ODR )
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
+#define CFG_FLASH_SIZE 8 /* flash size in MB */
+#define CFG_FLASH_EMPTY_INFO /* display empty sectors */
+#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
+
+#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \
+ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
+ BR_V) /* valid */
+#define CFG_OR0_PRELIM ( 0xFF000000 /* 16 MByte */ \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_9 \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD )
+ /* 0xFF006FF7 TODO SLOW 16 MB flash size */
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */
+#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */
+
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 135 /* sectors per device */
+
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#endif
+
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+
+#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_2 /* 0x00010002 */
+#define CFG_LBC_LBCR ( 0x00040000 /* TODO */ \
+ | (0xFF << LBCR_BMT_SHIFT) \
+ | 0xF ) /* 0x0004ff0f */
+
+#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */
+
+/* drivers/nand/nand.c */
+#define CFG_NAND_BASE 0xE2800000 /* 0xF0000000 */
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+
+#define CFG_BR1_PRELIM ( CFG_NAND_BASE \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V ) /* valid */
+#define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR )
+ /* 0xFFFF8396 */
+#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
+#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+
+#define CFG_VSC7385_BASE 0xF0000000
+
+#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */
+#define CFG_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */
+#define CFG_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/
+#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE/* Access window base at VSC7385 base */
+#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */
+
+/* local bus read write buffer mapping */
+#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
+#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
+#define CFG_LBLAWBAR3_PRELIM 0xFA000000
+#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8313@0"
+#define OF_SOC "soc8313@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8313@e0000000/serial@4500"
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
+#define CFG_I2C2_OFFSET 0x3100
+
+/* TSEC */
+#define CFG_TSEC1_OFFSET 0x24000
+#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
+#define CFG_TSEC2_OFFSET 0x25000
+#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
+#define CONFIG_NET_MULTI
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_MMIO_BASE 0x90000000
+#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xE2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+/*
+ * TSEC configuration
+ */
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+#define CONFIG_GMII 1 /* MII PHY management */
+#define CONFIG_MPC83XX_TSEC1 1
+
+#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0"
+#define CONFIG_MPC83XX_TSEC2 1
+#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1"
+#define TSEC1_PHY_ADDR 0x1c
+#define TSEC2_PHY_ADDR 4
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC1"
+
+/*
+ * Configure on-board RTC
+ */
+#define CONFIG_RTC_DS1337
+#define CFG_I2C_RTC_ADDR 0x68
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+ #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+
+/* Address and size of Redundant Environment Sector */
+#else
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CFG_BASE_COMMANDS ( CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_DHCP \
+ | CFG_CMD_I2C \
+ | CFG_CMD_MII \
+ | CFG_CMD_DATE \
+ | CFG_CMD_PCI)
+
+#define CONFIG_CMDLINE_EDITING 1
+
+#define CFG_RAMBOOT_COMMANDS (CFG_BASE_COMMANDS & \
+ ~(CFG_CMD_ENV | CFG_CMD_LOADS))
+
+#if defined(CFG_RAMBOOT)
+#define CONFIG_COMMANDS CFG_RAMBOOT_COMMANDS
+#else
+#define CONFIG_COMMANDS CFG_BASE_COMMANDS
+#endif
+
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 16384
+#define CFG_CACHELINE_SIZE 32
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+
+#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */
+
+#ifdef CFG_66MHZ
+
+/* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */
+/* 0x62040000 */
+#define CFG_HRCW_LOW (\
+ 0x20000000 /* reserved, must be set */ |\
+ HRCWL_DDRCM |\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_CSB_TO_CLKIN_2X1 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#elif defined(CFG_33MHZ)
+
+/* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
+/* 0x65040000 */
+#define CFG_HRCW_LOW (\
+ 0x20000000 /* reserved, must be set */ |\
+ HRCWL_DDRCM |\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_CSB_TO_CLKIN_5X1 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#endif
+
+/* 0xa0606c00 */
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_RGMII |\
+ HRCWH_TSEC2M_IN_RGMII |\
+ HRCWH_BIG_ENDIAN |\
+ HRCWH_LALE_NORMAL)
+
+/* System IO Config */
+#define CFG_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */
+#define CFG_SICRL SICRL_USBDR /* Enable Internal USB Phy */
+
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+
+#define CFG_HID2 HID2_HBE
+
+/* DDR @ 0x00000000 */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI @ 0x80000000 */
+#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10)
+#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* PCI2 not supported on 8313 */
+#define CFG_IBAT3L (0)
+#define CFG_IBAT3U (0)
+#define CFG_IBAT4L (0)
+#define CFG_IBAT4U (0)
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CFG_IBAT6L (0xF0000000 | BATL_PP_10)
+#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_IBAT7L (0)
+#define CFG_IBAT7U (0)
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ETHADDR 00:E0:0C:00:95:01
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:E0:0C:00:95:02
+
+#define CONFIG_IPADDR 10.0.0.2
+#define CONFIG_SERVERIP 10.0.0.1
+#define CONFIG_GATEWAYIP 10.0.0.1
+#define CONFIG_NETMASK 255.0.0.0
+#define CONFIG_NETDEV eth1
+
+#define CONFIG_HOSTNAME mpc8313erdb
+#define CONFIG_ROOTPATH /nfs/root/path
+#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
+#define CONFIG_FDTFILE mpc8313erdb.dtb
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
+#define CONFIG_BAUDRATE 115200
+
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "ethprime=TSEC1\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
+ "console=ttyS0\0" \
+ "setbootargs=setenv bootargs " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+ "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv rootdev /dev/nfs;" \
+ "run setbootargs;" \
+ "run setipargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv rootdev /dev/ram;" \
+ "run setbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif /* __CONFIG_H */
#define CFG_MEMTEST_START 0x1000 /* memtest region */
#define CFG_MEMTEST_END 0x2000
+#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
+ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
#ifdef CONFIG_HARD_I2C
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
#endif
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
+++ /dev/null
-/*
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * (C) Copyright 2004 Wind River Systems Inc <www.windriver.com>.
- * Added support for Wind River SBC8560 board
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
-/* make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#if XXX
-#define DEBUG /* General debug */
-#define ET_DEBUG
-#endif
-#define TSEC_DEBUG
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
-
-
-#define CONFIG_CPM2 1 /* has CPM2 */
-#define CONFIG_SBC8560 1 /* configuration for SBC8560 board */
-
-#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific (supplement) */
-
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_PCI /* pci ethernet support */
-#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
-
-
-#define CONFIG_ENV_OVERWRITE
-
-/* Using Localbus SDRAM to emulate flash before we can program the flash,
- * normally you need a flash-boot image(u-boot.bin), if so undef this.
- */
-#undef CONFIG_RAM_AS_FLASH
-
-#if defined(CONFIG_PCI_66) /* some PCI card is 33Mhz only */
- #define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */
-#else
- #define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */
-#endif
-
-/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
-
-#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
- defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
- defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC))
-#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
-#endif
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-
-#if XXX
- #define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
-#else
- #define CFG_CCSRBAR 0xff700000 /* default CCSRBAR */
-#endif
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 512 /* DDR is 512MB */
-#define SPD_EEPROM_ADDRESS 0x55 /* DDR DIMM */
-
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-
-#if defined(CONFIG_MPC85xx_REV1)
- #define CONFIG_DDR_DLL /* possible DLL fix needed */
-#endif
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-#if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
- #define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 8M */
- #define CFG_BR0_PRELIM 0xf8000801 /* port size 8bit */
- #define CFG_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */
-#else /* Boot from real Flash */
- #define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
- #define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */
- #define CFG_BR0_PRELIM 0xff800801 /* port size 8bit */
- #define CFG_OR0_PRELIM 0xff800ff7 /* 8MB Flash */
-#endif
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/* local bus definitions */
-#define CFG_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */
-#define CFG_OR1_PRELIM 0xfc000ff7
-
-#define CFG_BR2_PRELIM 0x00000000 /* CS2 not used */
-#define CFG_OR2_PRELIM 0x00000000
-
-#define CFG_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */
-#define CFG_OR3_PRELIM 0xfc000cc1
-
-#if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */
-#else
- #define CFG_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */
-#endif
-#define CFG_OR4_PRELIM 0xfc000cc1
-
-#define CFG_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */
-#if 1
- #define CFG_OR5_PRELIM 0xff000ff7
-#else
- #define CFG_OR5_PRELIM 0xff0000f0
-#endif
-
-#define CFG_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */
-#define CFG_OR6_PRELIM 0xfc000ff7
-#define CFG_LBC_LCRR 0x00030002 /* local bus freq */
-#define CFG_LBC_LBCR 0x00000000
-#define CFG_LBC_LSRT 0x20000000
-#define CFG_LBC_MRTPR 0x20000000
-#define CFG_LBC_LSDMR_1 0x2861b723
-#define CFG_LBC_LSDMR_2 0x0861b723
-#define CFG_LBC_LSDMR_3 0x0861b723
-#define CFG_LBC_LSDMR_4 0x1861b723
-#define CFG_LBC_LSDMR_5 0x4061b723
-
-/* just hijack the MOT BCSR def for SBC8560 misc devices */
-#define CFG_BCSR ((CFG_BR5_PRELIM & 0xff000000)|0x00400000)
-/* the size of CS5 needs to be >= 16M for TLB and LAW setups */
-
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-
-#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK 1843200 /* get_bus_freq(0) */
-#define CONFIG_BAUDRATE 9600
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CFG_NS16550_COM1 ((CFG_BR5_PRELIM & 0xff000000)+0x00700000)
-#define CFG_NS16550_COM2 ((CFG_BR5_PRELIM & 0xff000000)+0x00800000)
-
-/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-
-#define CFG_PCI_MEM_BASE 0xC0000000
-#define CFG_PCI_MEM_PHYS 0xC0000000
-#define CFG_PCI_MEM_SIZE 0x10000000
-
-#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
-
-# define CONFIG_NET_MULTI 1
-# define CONFIG_MII 1 /* MII PHY management */
-# define CONFIG_MPC85xx_TSEC1
-# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0"
-# define TSEC1_PHY_ADDR 25
-# define TSEC1_PHYIDX 0
-/* Options are: TSEC0 */
-# define CONFIG_ETHPRIME "TSEC0"
-
-
-#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
-
- #undef CONFIG_ETHER_NONE /* define if ether on something else */
- #define CONFIG_ETHER_ON_FCC2 /* cpm FCC ethernet support */
- #define CONFIG_ETHER_INDEX 2 /* which channel for ether */
-
- #if (CONFIG_ETHER_INDEX == 2)
- /*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers
- * - Full duplex
- */
- #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CFG_CPMFCR_RAMTYPE 0
- #define CFG_FCC_PSMR (FCC_PSMR_FDE)
-
- #elif (CONFIG_ETHER_INDEX == 3)
- /* need more definitions here for FE3 */
- #endif /* CONFIG_ETHER_INDEX */
-
- #define CONFIG_MII /* MII PHY management */
- #define CONFIG_BITBANGMII /* bit-bang MII PHY management */
- /*
- * GPIO pins used for bit-banged MII communications
- */
- #define MDIO_PORT 2 /* Port C */
- #define MDIO_ACTIVE (iop->pdir |= 0x00400000)
- #define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
- #define MDIO_READ ((iop->pdat & 0x00400000) != 0)
-
- #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
- else iop->pdat &= ~0x00400000
-
- #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
- else iop->pdat &= ~0x00200000
-
- #define MIIDELAY udelay(1)
-
-#endif
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#if 0
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION /* use hardware protection */
-#endif
-#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
-
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-
-#if 0
-/* XXX This doesn't work and I don't want to fix it */
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
- #define CFG_RAMBOOT
-#else
- #undef CFG_RAMBOOT
-#endif
-#endif
-
-/* Environment */
-#if !defined(CFG_RAMBOOT)
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_ENV_IS_NOWHERE
- #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
- #define CFG_ENV_SIZE 0x2000
- #else
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
- #define CFG_ENV_SIZE 0x2000 /* CFG_ENV_SECT_SIZE */
- #endif
-#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=192.168.0.251:/tftpboot ip=192.168.0.105:192.168.0.251::255.255.255.0:sbc8560:eth0:off console=ttyS0,9600"
-/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
-#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000"
-#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV | \
- CFG_CMD_LOADS ))
- #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV))
- #endif
-#else
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C)
- #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C)
- #endif
-#endif
-
-#include <cmd_confdefs.h>
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "SBC8560=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x1000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
- #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/*Note: change below for your network setting!!! */
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-# define CONFIG_ETHADDR 00:vv:ww:xx:yy:8a
-# define CONFIG_HAS_ETH1
-# define CONFIG_ETH1ADDR 00:vv:ww:xx:yy:8b
-# define CONFIG_HAS_ETH2
-# define CONFIG_ETH2ADDR 00:vv:ww:xx:yy:8c
-#endif
-
-#define CONFIG_SERVERIP YourServerIP
-#define CONFIG_IPADDR YourTargetIP
-#define CONFIG_GATEWAYIP YourGatewayIP
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_HOSTNAME SBC8560
-#define CONFIG_ROOTPATH YourRootPath
-#define CONFIG_BOOTFILE YourImageName
-
-#endif /* __CONFIG_H */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133) && !defined(CONFIG_CAM5200)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK) && !defined(CONFIG_CAM5200)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock of
+ * 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
#define CONFIG_ACADIA 1 /* Board is Acadia */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_405EZ 1 /* Specifc 405EZ support*/
-#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */
+/* Detect Acadia PLL input clock automatically via CPLD bit */
+#define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \
+ 66666666 : 33333000)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_F 1 /* Call misc_init_f */
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
-#if 0 /* test-only */
-#define TEST_ONLY_NAND
-#endif
-
-#ifdef TEST_ONLY_NAND
-#define CMD_NAND CFG_CMD_NAND
-#else
-#define CMD_NAND 0
-#endif
-
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
- CMD_NAND | \
+ CFG_CMD_NAND | \
CFG_CMD_NET | \
CFG_CMD_NFS | \
CFG_CMD_PCI | \
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#ifdef TEST_ONLY_NAND
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
#define NAND_MAX_CHIPS 1
#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-#endif
/*-----------------------------------------------------------------------
* Cache Configuration
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
-#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (Flash) initialization */
#define CFG_EBC_PB0AP 0x03337200
/*-----------------------------------------------------------------------
* Definitions for GPIO_0 setup (PPC405EZ specific)
*
- * GPIO0[0-3] - External Bus Controller CS_4 - CS_7 Outputs
+ * GPIO0[0-2] - External Bus Controller CS_4 - CS_6 Outputs
+ * GPIO0[3] - NAND FLASH Controller CE3 (NFCE3) Output
* GPIO0[4] - External Bus Controller Hold Input
* GPIO0[5] - External Bus Controller Priority Input
* GPIO0[6] - External Bus Controller HLDA Output
*/
#define CFG_GPIO0_TCR 0xC0000000
#define CFG_GPIO0_OSRL 0x50000000
-#define CFG_GPIO0_OSRH 0x00000055
+#define CFG_GPIO0_OSRH 0x02000055
#define CFG_GPIO0_ISR1L 0x00000000
#define CFG_GPIO0_ISR1H 0x00000055
-#define CFG_GPIO0_TSRL 0x00000000
+#define CFG_GPIO0_TSRL 0x02000000
#define CFG_GPIO0_TSRH 0x00000055
/*-----------------------------------------------------------------------
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* Flash configuration, expect one 16 Megabyte Bank at most
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* Flash configuration
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
#include "../board/xilinx/ml401/xparameters.h"
#define CONFIG_MICROBLAZE 1 /* MicroBlaze CPU */
+#define MICROBLAZE_V5 1
#define CONFIG_ML401 1 /* ML401 Board */
/* uart */
#define CFG_BAUDRATE_TABLE { CONFIG_BAUDRATE }
/* setting reset address */
-#define CFG_RESET_ADDRESS TEXT_BASE
+/*#define CFG_RESET_ADDRESS TEXT_BASE*/
/* ethernet */
#define CONFIG_EMACLITE 1
-#define XPAR_EMAC_0_DEVICE_ID XPAR_XEMAC_NUM_INSTANCES
+#define XPAR_EMAC_0_DEVICE_ID XPAR_OPB_ETHERNET_0_DEVICE_ID
/* gpio */
#define CFG_GPIO_0 1
#define FREQUENCE XILINX_CLOCK_FREQ
#define CFG_TIMER_0_PRELOAD ( FREQUENCE/1000 )
+/* FSL */
+#define CFG_FSL_2
+#define FSL_INTR_2 1
+
/*
* memory layout - Example
* TEXT_BASE = 0x1200_0000;
/* global pointer */
#define CFG_GBL_DATA_SIZE 0x1000 /* size of global data */
-#define CFG_GBL_DATA_OFFSET (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE) /* start of global data */
+/* start of global data */
+#define CFG_GBL_DATA_OFFSET (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE)
/* monitor code */
#define SIZE 0x40000
#define CFG_FLASH_EMPTY_INFO 1 /* ?empty sector */
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+ #define CFG_FLASH_PROTECTION /* hardware flash protection */
#ifdef RAMENV
#define CFG_ENV_IS_NOWHERE 1
#define CFG_ENV_IS_NOWHERE 1
#define CFG_ENV_SIZE 0x1000
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SIZE)
+ #define CFG_FLASH_PROTECTION /* hardware flash protection */
#endif /* !FLASH */
#ifdef FLASH
CFG_CMD_IMI |\
CFG_CMD_NET |\
CFG_CMD_CACHE |\
+ CFG_CMD_FAT |\
+ CFG_CMD_EXT2 |\
+ CFG_CMD_JFFS2 |\
+ CFG_CMD_ECHO |\
CFG_CMD_IMLS |\
CFG_CMD_FLASH |\
+ CFG_CMD_MFSL |\
CFG_CMD_PING \
)
#else /* !RAMENV */
CFG_CMD_FLASH |\
CFG_CMD_PING |\
CFG_CMD_ENV |\
+ CFG_CMD_FAT |\
+ CFG_CMD_EXT2 |\
+ CFG_CMD_JFFS2 |\
+ CFG_CMD_ECHO |\
+ CFG_CMD_MFSL |\
CFG_CMD_SAVES \
)
CFG_CMD_BDI |\
CFG_CMD_RUN |\
CFG_CMD_LOADS |\
+ CFG_CMD_FAT |\
+ CFG_CMD_EXT2 |\
CFG_CMD_LOADB |\
CFG_CMD_IMI |\
CFG_CMD_NET |\
CFG_CMD_CACHE |\
+ CFG_CMD_MFSL |\
CFG_CMD_PING \
)
#endif /* !FLASH */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
+#if (CONFIG_COMMANDS & CFG_CMD_JFFS2)
+/* JFFS2 partitions */
+#define CONFIG_JFFS2_CMDLINE /* mtdparts command line support */
+#define MTDIDS_DEFAULT "nor0=ml401-0"
+
+/* default mtd partition table */
+#define MTDPARTS_DEFAULT "mtdparts=ml401-0:256k(u-boot),"\
+ "256k(env),3m(kernel),1m(romfs),"\
+ "1m(cramfs),-(jffs2)"
+#endif
+
/* Miscellaneous configurable options */
#define CFG_PROMPT "U-Boot-mONStR> "
#define CFG_CBSIZE 512 /* size of console buffer */
#define CFG_LONGHELP
#define CFG_LOAD_ADDR 0x12000000 /* default load address */
-#define CONFIG_BOOTDELAY 30
+#define CONFIG_BOOTDELAY 30
#define CONFIG_BOOTARGS "root=romfs"
#define CONFIG_HOSTNAME "ml401"
#define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm"
#define CFG_HZ 1000
/* system ace */
-/*#define CONFIG_SYSTEMACE
-#define DEBUG_SYSTEMACE
-#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR
-#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH
-#define CONFIG_DOS_PARTITION
-*/
+#define CONFIG_SYSTEMACE
+/* #define DEBUG_SYSTEMACE */
+#define SYSTEMACE_CONFIG_FPGA
+#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR
+#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_PREBOOT "echo U-BOOT for ML401;setenv preboot;echo"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" /* hardware flash protection */\
+ "nor0=ml401-0\0"\
+ "mtdparts=mtdparts=ml401-0:"\
+ "256k(u-boot),256k(env),3m(kernel),"\
+ "1m(romfs),1m(cramfs),-(jffs2)\0"
+
#endif /* __CONFIG_H */
#ifndef __CONFIG_H
#define __CONFIG_H
-
/*
* High Level Configuration Options
*/
-
/* CPU and board */
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* More exactly a MPC5200 */
CFG_CMD_MII | \
CFG_CMD_BEDBUG | \
CFG_CMD_NET | \
- CFG_CMD_PING)
+ CFG_CMD_PING | \
+ CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_I2C | \
+ CFG_CMD_DATE | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DTT)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_PHY_ADDR 0x2
#define CONFIG_PHY_TYPE 0x79c874
-
+#define CONFIG_RESET_PHY_R 1
/*
* Autobooting
* Default environment settings
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
- "sdram_test=0\0" \
"netdev=eth0\0" \
"hostname=motionpro\0" \
"netmask=255.255.0.0\0" \
"ipaddr=192.168.160.22\0" \
"serverip=192.168.1.1\0" \
"gatewayip=192.168.1.1\0" \
- "kernel_addr=200000\0" \
+ "console=ttyPSC0,115200\0" \
"u-boot_addr=100000\0" \
- "kernel_sector=20\0" \
- "kernel_size=1000\0" \
- "console=ttyS0,115200\0" \
+ "kernel_addr=200000\0" \
+ "fdt_addr=400000\0" \
+ "ramdisk_addr=500000\0" \
+ "multi_image_addr=800000\0" \
"rootpath=/opt/eldk-4.1/ppc_6xx\0" \
- "bootfile=/tftpboot/motionpro/uImage\0" \
"u-boot=/tftpboot/motionpro/u-boot.bin\0" \
- "load=tftp $(u-boot_addr) $(u-boot)\0" \
+ "bootfile=/tftpboot/motionpro/uImage\0" \
+ "fdt_file=/tftpboot/motionpro/motionpro.dtb\0" \
+ "ramdisk_file=/tftpboot/motionpro/uRamdisk\0" \
+ "multi_image_file=kernel+initrd+dtb.img\0" \
+ "load=tftp ${u-boot_addr} ${u-boot}\0" \
"update=prot off fff00000 fff3ffff; era fff00000 fff3ffff; " \
- "cp.b $(u-boot_addr) fff00000 $(filesize);" \
+ "cp.b ${u-boot_addr} fff00000 ${filesize};" \
"prot on fff00000 fff3ffff\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) console=$(console) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):" \
- "$(netmask):$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip;bootm $(kernel_addr) " \
- "$(ramdisk_addr)\0" \
- "net_nfs=tftp $(kernel_addr) $(bootfile); run nfsargs addip; " \
- "bootm $(kernel_addr)\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "fstype=ext3\0" \
- "fatargs=setenv bootargs init=/linuxrc rw\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "fat_args=setenv bootargs rw\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:" \
+ "${netmask}:${hostname}:${netdev}:off panic=1 " \
+ "console=${console}\0" \
+ "net_nfs=tftp ${kernel_addr} ${bootfile}; " \
+ "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip; " \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_self=tftp ${kernel_addr} ${bootfile}; " \
+ "tftp ${fdt_addr} ${fdt_file}; " \
+ "tftp ${ramdisk_addr} ${ramdisk_file}; " \
+ "run ramargs addip; " \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "fat_multi=run fat_args addip; fatload ide 0:1 " \
+ "${multi_image_addr} ${multi_image_file}; " \
+ "bootm ${multi_image_addr}\0" \
""
#define CONFIG_BOOTCOMMAND "run net_nfs"
-
/*
* do board-specific init
*/
/*
+ * Set IPB speed to 100MHz
+ */
+#define CFG_IPBCLK_EQUALS_XLBCLK
+
+
+/*
* Memory map
*/
/*
#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
#define CONFIG_FLASH_16BIT /* Flash is 16-bit */
+/*
+ * MTD configuration
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=motionpro-0"
+#define MTDPARTS_DEFAULT "mtdparts=motionpro-0:" \
+ "13m(fs),2m(kernel),256k(uboot)," \
+ "64k(env),64k(redund_env),64k(dtb)," \
+ "-(user_data)"
+
+/*
+ * IDE/ATA configuration
+ */
+#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+#define CFG_IDE_MAXBUS 1
+#define CFG_IDE_MAXDEVICE 1
+#define CONFIG_IDE_PREINIT
+
+#define CFG_ATA_DATA_OFFSET 0x0060
+#define CFG_ATA_REG_OFFSET CFG_ATA_DATA_OFFSET
+#define CFG_ATA_STRIDE 4
+#define CONFIG_DOS_PARTITION
+
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CFG_I2C_MODULE 2 /* select I2C module #2 */
+#define CFG_I2C_SPEED 100000 /* 100 kHz */
+#define CFG_I2C_SLAVE 0x7F
+
+
+/*
+ * EEPROM configuration
+ */
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE 1 /* DTT driver needs this */
+#define CFG_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
+#define CFG_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */
+
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_DS1337 1
+#define CFG_I2C_RTC_ADDR 0x68
+
+
+/*
+ * Status LED configuration
+ */
+#define CONFIG_STATUS_LED /* Status LED enabled */
+#define CONFIG_BOARD_SPECIFIC_LED
+
+#define ENABLE_GPIO_OUT 0x00000024
+#define LED_ON 0x00000010
+
+#ifndef __ASSEMBLY__
+/*
+ * In case of Motion-PRO, a LED is identified by its corresponding
+ * GPT Enable and Mode Select Register.
+ */
+typedef volatile unsigned long * led_id_t;
+
+extern void __led_init(led_id_t id, int state);
+extern void __led_toggle(led_id_t id);
+extern void __led_set(led_id_t id, int state);
+#endif /* __ASSEMBLY__ */
+
+
+/*
+ * Temperature sensor
+ */
+#define CONFIG_DTT_LM75 1
+#define CONFIG_DTT_SENSORS { 0x49 }
+
/*
* Environment settings
#define CFG_ENV_SIZE 0x1000
#define CFG_ENV_SECT_SIZE 0x10000
+/* Configuration of redundant environment */
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*
* Pin multiplexing configuration
/*
+ * Motion-PRO's CPLD revision control register
+ */
+#define CPLD_REV_REGISTER (CFG_CS2_START + 0x06)
+
+
+/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
/* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
#define CFG_RESET_ADDRESS 0xfff00100
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+
#endif /* __CONFIG_H */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
#endif
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
/*
* For 66 MHz PCI clock additional Wait State is needed for CS0 (flash).
*/
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
#define CONFIG_4xx 1 /* ... PPC4xx family */
/* Detect Sequoia PLL input clock automatically via CPLD bit */
#define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
- 3333333 : 33000000)
+ 33333333 : 33000000)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
CFG_CMD_LOADS |\
CFG_CMD_LOADB |\
CFG_CMD_MISC |\
+ CFG_CMD_FAT |\
+ CFG_CMD_EXT2 |\
CFG_CMD_PING \
)
"base 0;" \
"echo"
-
/* system ace */
-/*#define CONFIG_SYSTEMACE
-#define DEBUG_SYSTEMACE
-#define CFG_SYSTEMACE_BASE 0xCF000000
-#define CFG_SYSTEMACE_WIDTH 16
-#define CONFIG_DOS_PARTITION*/
+#define CONFIG_SYSTEMACE
+/* #define DEBUG_SYSTEMACE */
+#define SYSTEMACE_CONFIG_FPGA
+#define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR
+#define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH
+#define CONFIG_DOS_PARTITION
#endif /* __CONFIG_H */
#endif /* __PPC__ */
-#if defined (__ARM__) || defined (__I386__) || defined (__M68K__) || defined (__bfin__)
+#if defined (__ARM__) || defined (__I386__) || defined (__M68K__) || defined (__bfin__) ||\
+ defined (__microblaze__)
struct stat {
unsigned short st_dev;
#define SPR_8321E_REV11 0x80660011
#define SPR_8321_REV11 0x80670011
+#define SPR_8311_REV10 0x80B30010
+#define SPR_8311E_REV10 0x80B20010
+#define SPR_8313_REV10 0x80B10010
+#define SPR_8313E_REV10 0x80B00010
+
/* SPCR - System Priority Configuration Register
*/
#define SPCR_PCIHPE 0x10000000 /* PCI Highest Priority Enable */
#define SPCR_TSEC2BDP_SHIFT (31-29)
#define SPCR_TSEC2EP 0x00000003 /* TSEC2 emergency priority */
#define SPCR_TSEC2EP_SHIFT (31-31)
+
+#elif defined(CONFIG_MPC831X)
+/* SPCR bits - MPC831x specific */
+#define SPCR_TSECDP 0x00003000 /* TSEC data priority */
+#define SPCR_TSECDP_SHIFT (31-19)
+#define SPCR_TSECEP 0x00000C00 /* TSEC emergency priority */
+#define SPCR_TSECEP_SHIFT (31-21)
+#define SPCR_TSECBDP 0x00000300 /* TSEC buffer descriptor priority */
+#define SPCR_TSECBDP_SHIFT (31-23)
#endif
/* SICRL/H - System I/O Configuration Register Low/High
#define SICRL_PCI_MSRC 0x10000000
#define SICRL_URT_CTPR 0x06000000
#define SICRL_IRQ_CTPR 0x00C00000
+
+#elif defined(CONFIG_MPC831X)
+/* SICRL bits - MPC831x specific */
+#define SICRL_LBC 0x30000000
+#define SICRL_UART 0x0C000000
+#define SICRL_SPI_A 0x03000000
+#define SICRL_SPI_B 0x00C00000
+#define SICRL_SPI_C 0x00300000
+#define SICRL_SPI_D 0x000C0000
+#define SICRL_USBDR 0x00000C00
+#define SICRL_ETSEC1_A 0x0000000C
+#define SICRL_ETSEC2_A 0x00000003
+
+/* SICRH bits - MPC831x specific */
+#define SICRH_INTR_A 0x02000000
+#define SICRH_INTR_B 0x00C00000
+#define SICRH_IIC 0x00300000
+#define SICRH_ETSEC2_B 0x000C0000
+#define SICRH_ETSEC2_C 0x00030000
+#define SICRH_ETSEC2_D 0x0000C000
+#define SICRH_ETSEC2_E 0x00003000
+#define SICRH_ETSEC2_F 0x00000C00
+#define SICRH_ETSEC2_G 0x00000300
+#define SICRH_ETSEC1_B 0x00000080
+#define SICRH_ETSEC1_C 0x00000060
+#define SICRH_GTX1_DLY 0x00000008
+#define SICRH_GTX2_DLY 0x00000004
+#define SICRH_TSOBI1 0x00000002
+#define SICRH_TSOBI2 0x00000001
+
#endif
/* SWCRR - System Watchdog Control Register
#define HRCWH_ROM_LOC_LOCAL_16BIT 0x00600000
#define HRCWH_ROM_LOC_LOCAL_32BIT 0x00700000
+#if defined(CONFIG_MPC831X)
+#define HRCWH_ROM_LOC_NAND_SP_8BIT 0x00100000
+#define HRCWH_ROM_LOC_NAND_SP_16BIT 0x00200000
+#define HRCWH_ROM_LOC_NAND_LP_8BIT 0x00500000
+#define HRCWH_ROM_LOC_NAND_LP_16BIT 0x00600000
+
+#define HRCWH_RL_EXT_LEGACY 0x00000000
+#define HRCWH_RL_EXT_NAND 0x00040000
+
+#define HRCWH_TSEC1M_IN_MII 0x00000000
+#define HRCWH_TSEC1M_IN_RMII 0x00002000
+#define HRCWH_TSEC1M_IN_RGMII 0x00006000
+#define HRCWH_TSEC1M_IN_RTBI 0x0000A000
+#define HRCWH_TSEC1M_IN_SGMII 0x0000C000
+
+#define HRCWH_TSEC2M_IN_MII 0x00000000
+#define HRCWH_TSEC2M_IN_RMII 0x00000400
+#define HRCWH_TSEC2M_IN_RGMII 0x00000C00
+#define HRCWH_TSEC2M_IN_RTBI 0x00001400
+#define HRCWH_TSEC2M_IN_SGMII 0x00001800
+#endif
+
#if defined(CONFIG_MPC834X)
#define HRCWH_TSEC1M_IN_RGMII 0x00000000
#define HRCWH_TSEC1M_IN_RTBI 0x00004000
#define SCCR_TSEC2CM_1 0x10000000
#define SCCR_TSEC2CM_2 0x20000000
#define SCCR_TSEC2CM_3 0x30000000
+
+#elif defined(CONFIG_MPC831X)
+/* TSEC1 bits are for TSEC2 as well */
+#define SCCR_TSEC1CM 0xc0000000
+#define SCCR_TSEC1CM_SHIFT 30
+#define SCCR_TSEC1CM_1 0x40000000
+#define SCCR_TSEC1CM_2 0x80000000
+#define SCCR_TSEC1CM_3 0xC0000000
+
+#define SCCR_TSEC1ON 0x20000000
+#define SCCR_TSEC2ON 0x10000000
+
#endif
#define SCCR_USBMPHCM 0x00c00000
#define CSCONFIG_COL_BIT_10 0x00000002
#define CSCONFIG_COL_BIT_11 0x00000003
+/* TIMING_CFG_0 - DDR SDRAM Timing Configuration 0
+ */
+#define TIMING_CFG0_RWT 0xC0000000
+#define TIMING_CFG0_RWT_SHIFT 30
+#define TIMING_CFG0_WRT 0x30000000
+#define TIMING_CFG0_WRT_SHIFT 28
+#define TIMING_CFG0_RRT 0x0C000000
+#define TIMING_CFG0_RRT_SHIFT 26
+#define TIMING_CFG0_WWT 0x03000000
+#define TIMING_CFG0_WWT_SHIFT 24
+#define TIMING_CFG0_ACT_PD_EXIT 0x00700000
+#define TIMING_CFG0_ACT_PD_EXIT_SHIFT 20
+#define TIMING_CFG0_PRE_PD_EXIT 0x00070000
+#define TIMING_CFG0_PRE_PD_EXIT_SHIFT 16
+#define TIMING_CFG0_ODT_PD_EXIT 0x00000F00
+#define TIMING_CFG0_ODT_PD_EXIT_SHIFT 8
+#define TIMING_CFG0_MRS_CYC 0x00000F00
+#define TIMING_CFG0_MRS_CYC_SHIFT 0
+
/* TIMING_CFG_1 - DDR SDRAM Timing Configuration 1
*/
#define TIMING_CFG1_PRETOACT 0x70000000
#define TIMING_CFG2_WR_DATA_DELAY_SHIFT 10
#define TIMING_CFG2_CPO_DEF 0x00000000 /* default (= CASLAT + 1) */
+#define TIMING_CFG2_ADD_LAT 0x70000000
+#define TIMING_CFG2_ADD_LAT_SHIFT 28
+#define TIMING_CFG2_WR_LAT_DELAY 0x00380000
+#define TIMING_CFG2_WR_LAT_DELAY_SHIFT 19
+#define TIMING_CFG2_RD_TO_PRE 0x0000E000
+#define TIMING_CFG2_RD_TO_PRE_SHIFT 13
+#define TIMING_CFG2_CKE_PLS 0x000001C0
+#define TIMING_CFG2_CKE_PLS_SHIFT 6
+#define TIMING_CFG2_FOUR_ACT 0x0000003F
+#define TIMING_CFG2_FOUR_ACT_SHIFT 0
+
/* DDR_SDRAM_CFG - DDR SDRAM Control Configuration
*/
#define SDRAM_CFG_MEM_EN 0x80000000
#define SDRAM_CFG_ECC_EN 0x20000000
#define SDRAM_CFG_RD_EN 0x10000000
#define SDRAM_CFG_SDRAM_TYPE 0x03000000
+#define SDRAM_CFG_SDRAM_TYPE_DDR 0x02000000
#define SDRAM_CFG_SDRAM_TYPE_SHIFT 24
#define SDRAM_CFG_DYN_PWR 0x00200000
#define SDRAM_CFG_32_BE 0x00080000
#define SDRAM_CFG_8_BE 0x00040000
#define SDRAM_CFG_NCAP 0x00020000
#define SDRAM_CFG_2T_EN 0x00008000
-#define SDRAM_CFG_SDRAM_TYPE_DDR 0x02000000
+#define SDRAM_CFG_BI 0x00000001
/* DDR_SDRAM_MODE - DDR SDRAM Mode Register
*/
#define BR_PS_32 0x00001800 /* Port Size 32 bit */
#define BR_DECC 0x00000600
#define BR_DECC_SHIFT 9
+#define BR_DECC_OFF 0x00000000
+#define BR_DECC_CHK 0x00000200
+#define BR_DECC_CHK_GEN 0x00000400
#define BR_WP 0x00000100
#define BR_WP_SHIFT 8
#define BR_MSEL 0x000000E0
#define BR_MSEL_SHIFT 5
#define BR_MS_GPCM 0x00000000 /* GPCM */
+#define BR_MS_FCM 0x00000020 /* FCM */
#define BR_MS_SDRAM 0x00000060 /* SDRAM */
#define BR_MS_UPMA 0x00000080 /* UPMA */
#define BR_MS_UPMB 0x000000A0 /* UPMB */
#define OR_GPCM_EAD 0x00000001
#define OR_GPCM_EAD_SHIFT 0
+#define OR_FCM_AM 0xFFFF8000
+#define OR_FCM_AM_SHIFT 15
+#define OR_FCM_BCTLD 0x00001000
+#define OR_FCM_BCTLD_SHIFT 12
+#define OR_FCM_PGS 0x00000400
+#define OR_FCM_PGS_SHIFT 10
+#define OR_FCM_CSCT 0x00000200
+#define OR_FCM_CSCT_SHIFT 9
+#define OR_FCM_CST 0x00000100
+#define OR_FCM_CST_SHIFT 8
+#define OR_FCM_CHT 0x00000080
+#define OR_FCM_CHT_SHIFT 7
+#define OR_FCM_SCY 0x00000070
+#define OR_FCM_SCY_SHIFT 4
+#define OR_FCM_SCY_1 0x00000010
+#define OR_FCM_SCY_2 0x00000020
+#define OR_FCM_SCY_3 0x00000030
+#define OR_FCM_SCY_4 0x00000040
+#define OR_FCM_SCY_5 0x00000050
+#define OR_FCM_SCY_6 0x00000060
+#define OR_FCM_SCY_7 0x00000070
+#define OR_FCM_RST 0x00000008
+#define OR_FCM_RST_SHIFT 3
+#define OR_FCM_TRLX 0x00000004
+#define OR_FCM_TRLX_SHIFT 2
+#define OR_FCM_EHTR 0x00000002
+#define OR_FCM_EHTR_SHIFT 1
+
#define OR_UPM_AM 0xFFFF8000
#define OR_UPM_AM_SHIFT 15
#define OR_UPM_XAM 0x00006000
#define PIWAR_IWS_1G 0x0000001D
#define PIWAR_IWS_2G 0x0000001E
+/* PMCCR1 - PCI Configuration Register 1
+ */
+#define PMCCR1_POWER_OFF 0x00000020
+
+/* FMR - Flash Mode Register
+ */
+#define FMR_CWTO 0x0000F000
+#define FMR_CWTO_SHIFT 12
+#define FMR_BOOT 0x00000800
+#define FMR_ECCM 0x00000100
+#define FMR_AL 0x00000030
+#define FMR_AL_SHIFT 4
+#define FMR_OP 0x00000003
+#define FMR_OP_SHIFT 0
+
+/* FIR - Flash Instruction Register
+ */
+#define FIR_OP0 0xF0000000
+#define FIR_OP0_SHIFT 28
+#define FIR_OP1 0x0F000000
+#define FIR_OP1_SHIFT 24
+#define FIR_OP2 0x00F00000
+#define FIR_OP2_SHIFT 20
+#define FIR_OP3 0x000F0000
+#define FIR_OP3_SHIFT 16
+#define FIR_OP4 0x0000F000
+#define FIR_OP4_SHIFT 12
+#define FIR_OP5 0x00000F00
+#define FIR_OP5_SHIFT 8
+#define FIR_OP6 0x000000F0
+#define FIR_OP6_SHIFT 4
+#define FIR_OP7 0x0000000F
+#define FIR_OP7_SHIFT 0
+#define FIR_OP_NOP 0x0 /* No operation and end of sequence */
+#define FIR_OP_CA 0x1 /* Issue current column address */
+#define FIR_OP_PA 0x2 /* Issue current block+page address */
+#define FIR_OP_UA 0x3 /* Issue user defined address */
+#define FIR_OP_CM0 0x4 /* Issue command from FCR[CMD0] */
+#define FIR_OP_CM1 0x5 /* Issue command from FCR[CMD1] */
+#define FIR_OP_CM2 0x6 /* Issue command from FCR[CMD2] */
+#define FIR_OP_CM3 0x7 /* Issue command from FCR[CMD3] */
+#define FIR_OP_WB 0x8 /* Write FBCR bytes from FCM buffer */
+#define FIR_OP_WS 0x9 /* Write 1 or 2 bytes from MDR[AS] */
+#define FIR_OP_RB 0xA /* Read FBCR bytes to FCM buffer */
+#define FIR_OP_RS 0xB /* Read 1 or 2 bytes to MDR[AS] */
+#define FIR_OP_CW0 0xC /* Wait then issue FCR[CMD0] */
+#define FIR_OP_CW1 0xD /* Wait then issue FCR[CMD1] */
+#define FIR_OP_RBW 0xE /* Wait then read FBCR bytes */
+#define FIR_OP_RSW 0xF /* Wait then read 1 or 2 bytes */
+
+/* FCR - Flash Command Register
+ */
+#define FCR_CMD0 0xFF000000
+#define FCR_CMD0_SHIFT 24
+#define FCR_CMD1 0x00FF0000
+#define FCR_CMD1_SHIFT 16
+#define FCR_CMD2 0x0000FF00
+#define FCR_CMD2_SHIFT 8
+#define FCR_CMD3 0x000000FF
+#define FCR_CMD3_SHIFT 0
+
+/* FBAR - Flash Block Address Register
+ */
+#define FBAR_BLK 0x00FFFFFF
+
+/* FPAR - Flash Page Address Register
+ */
+#define FPAR_SP_PI 0x00007C00
+#define FPAR_SP_PI_SHIFT 10
+#define FPAR_SP_MS 0x00000200
+#define FPAR_SP_CI 0x000001FF
+#define FPAR_SP_CI_SHIFT 0
+#define FPAR_LP_PI 0x0003F000
+#define FPAR_LP_PI_SHIFT 12
+#define FPAR_LP_MS 0x00000800
+#define FPAR_LP_CI 0x000007FF
+#define FPAR_LP_CI_SHIFT 0
+
+/* LTESR - Transfer Error Status Register
+ */
+#define LTESR_BM 0x80000000
+#define LTESR_FCT 0x40000000
+#define LTESR_PAR 0x20000000
+#define LTESR_WP 0x04000000
+#define LTESR_ATMW 0x00800000
+#define LTESR_ATMR 0x00400000
+#define LTESR_CS 0x00080000
+#define LTESR_CC 0x00000001
+
+/* DDR Control Driver Register
+ */
+#define DDRCDR_EN 0x40000000
+#define DDRCDR_PZ 0x3C000000
+#define DDRCDR_PZ_MAXZ 0x00000000
+#define DDRCDR_PZ_HIZ 0x20000000
+#define DDRCDR_PZ_NOMZ 0x30000000
+#define DDRCDR_PZ_LOZ 0x38000000
+#define DDRCDR_PZ_MINZ 0x3C000000
+#define DDRCDR_NZ 0x3C000000
+#define DDRCDR_NZ_MAXZ 0x00000000
+#define DDRCDR_NZ_HIZ 0x02000000
+#define DDRCDR_NZ_NOMZ 0x03000000
+#define DDRCDR_NZ_LOZ 0x03800000
+#define DDRCDR_NZ_MINZ 0x03C00000
+#define DDRCDR_ODT 0x00080000
+#define DDRCDR_DDR_CFG 0x00040000
+#define DDRCDR_M_ODR 0x00000002
+#define DDRCDR_Q_DRN 0x00000001
+
+#ifndef __ASSEMBLY__
+struct pci_region;
+void mpc83xx_pci_init(int num_buses, struct pci_region **reg, int warmboot);
+#endif
+
#endif /* __MPC83XX_H__ */
#define sdrcfga (SDR_DCR_BASE+0x0) /* ADDR */
#define sdrcfgd (SDR_DCR_BASE+0x1) /* Data */
-#define mtsdr(reg, data) mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data)
-#define mfsdr(reg, data) mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd)
+#define mtsdr(reg, data) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data); } while (0)
+#define mfsdr(reg, data) do { mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd); } while (0)
#define sdrnand0 0x4000
#define sdrultra0 0x4040
/*
* Macro for accessing the indirect CPR register
*/
-#define mtcpr(reg, data) mtdcr(cprcfga,reg);mtdcr(cprcfgd,data)
-#define mfcpr(reg, data) mtdcr(cprcfga,reg);data = mfdcr(cprcfgd)
+#define mtcpr(reg, data) do { mtdcr(cprcfga,reg);mtdcr(cprcfgd,data); } while (0)
+#define mfcpr(reg, data) do { mtdcr(cprcfga,reg);data = mfdcr(cprcfgd); } while (0)
#define CPR_CLKUPD_ENPLLCH_EN 0x40000000 /* Enable CPR PLL Changes */
#define CPR_CLKUPD_ENDVCH_EN 0x20000000 /* Enable CPR Sys. Div. Changes */
/*----------------------------------------------------------------------------+
| Clock / Power-on-reset DCR's.
+----------------------------------------------------------------------------*/
-#define CPR0_CFGADDR 0x00C
-#define CPR0_CFGDATA 0x00D
-
#define CPR0_CLKUPD 0x20
#define CPR0_CLKUPD_BSY_MASK 0x80000000
#define CPR0_CLKUPD_BSY_COMPLETED 0x00000000
#define mtsdr(reg, data) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data); } while (0)
#define mfsdr(reg, data) do { mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd); } while (0)
+/*
+ * All 44x except 440GP have CPR registers (indirect DCR)
+ */
+#if !defined(CONFIG_440GP)
+#define CPR0_CFGADDR 0x00C
+#define CPR0_CFGDATA 0x00D
+
+#define mtcpr(reg, data) do { \
+ mtdcr(CPR0_CFGADDR, reg); \
+ mtdcr(CPR0_CFGDATA, data); \
+ } while (0)
+
+#define mfcpr(reg, data) do { \
+ mtdcr(CPR0_CFGADDR, reg); \
+ data = mfdcr(CPR0_CFGDATA); \
+ } while (0)
+#endif
#ifndef __ASSEMBLY__
# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+#elif defined(CONFIG_MOTIONPRO)
+
+#define STATUS_LED_BIT ((vu_long *) MPC5XXX_GPT6_ENABLE)
+#define STATUS_LED_PERIOD (CFG_HZ / 10)
+#define STATUS_LED_STATE STATUS_LED_BLINKING
+
+#define STATUS_LED_BIT1 ((vu_long *) MPC5XXX_GPT7_ENABLE)
+#define STATUS_LED_PERIOD1 (CFG_HZ / 10)
+#define STATUS_LED_STATE1 STATUS_LED_OFF
+
+#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
#else
# error Status LED configuration missing
#endif
prt_8260_clks,
#endif /* CONFIG_8260 */
-#if defined(CONFIG_MPC83XX)
- print_clock_conf,
-#endif
-
checkcpu,
#if defined(CONFIG_MPC5xxx)
prt_mpc5xxx_clks,
bd->bi_procfreq = gd->cpu_clk; /* Processor Speed, In Hz */
bd->bi_plb_busfreq = gd->bus_clk;
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || \
+ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
+ defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
bd->bi_pci_busfreq = get_PCI_freq ();
bd->bi_opbfreq = get_OPB_freq ();
#elif defined(CONFIG_XILINX_ML300)
projects / platform / kernel / u-boot.git / commitdiff