@$(MKCONFIG) $(@:_config=) arm arm720t modnet50
evb4510_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm720t evb4510
+ @$(MKCONFIG) $(@:_config=) arm arm720t evb4510 NULL s3c4510b
lpc2292sodimm_config: unconfig
@$(MKCONFIG) $(@:_config=) arm arm720t lpc2292sodimm NULL lpc2292
except those marked below with a "*".
CONFIG_CMD_ASKENV * ask for env variable
- CONFIG_CMD_AUTOSCRIPT Autoscript Support
CONFIG_CMD_BDI bdinfo
CONFIG_CMD_BEDBUG * Include BedBug Debugger
CONFIG_CMD_BMP * BMP support
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
+ CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_CMD_USB * USB support
CONFIG_CMD_VFD * VFD support (TRAB)
Note: overly (ab)use of the default environment is
discouraged. Make sure to check other ways to preset
- the environment like the autoscript function or the
+ the environment like the "source" command or the
boot command first.
- DataFlash Support:
81 common/cmd_net.c NetLoop() back without error
-82 common/cmd_net.c size == 0 (File with size 0 loaded)
82 common/cmd_net.c trying automatic boot
- 83 common/cmd_net.c running autoscript
- -83 common/cmd_net.c some error in automatic boot or autoscript
+ 83 common/cmd_net.c running "source" command
+ -83 common/cmd_net.c some error in automatic boot or "source" command
84 common/cmd_net.c end without errors
FIT uImage format:
autoscript - if set to "yes" commands like "loadb", "loady",
"bootp", "tftpb", "rarpboot" and "nfs" will attempt
to automatically run script images (by internally
- calling "autoscript").
+ calling "source").
autoscript_uname - if script image is in a format (FIT) this
variable is used to get script subimage unit name.
setenv ("ethaddr", e);
}
}
- sprintf (bootcmd,"autoscript %X",(unsigned)bootscript);
+ sprintf (bootcmd,"source %X",(unsigned)bootscript);
setenv ("bootcmd", bootcmd);
return (0);
}
tftp $tftp_addr $bootcript
if imi $tftp_addr
then
- autoscript $tftp_addr
+ source $tftp_addr
fi
fi
#if defined(CONFIG_CMD_BSP)
extern int do_bootm (cmd_tbl_t *, int, int, char *[]);
-extern int do_autoscript (cmd_tbl_t *, int, int, char *[]);
+extern int do_source (cmd_tbl_t *, int, int, char *[]);
#define ADDRMASK 0xfffff000
case 1:
/*
- * Boot image via autoscr
+ * Boot image via "source" command
*/
printf("executing script at addr 0x%s ...\n", addr);
local_args[0] = addr;
local_args[1] = NULL;
- do_autoscript(cmdtp, 0, 1, local_args);
+ do_source(cmdtp, 0, 1, local_args);
break;
case 2:
if ((num >= 0) && (num <= 7)) {
if (mode & 1) {
/* turn on 'loopback' mode */
- out_8(&uart->mcr, MCR_LOOP);
+ out_8(&uart->mcr, UART_MCR_LOOP);
} else {
/*
* establish the UART's operational parameters
* set DLAB=1, so rbr accesses DLL
*/
- out_8(&uart->lcr, LCR_DLAB);
+ out_8(&uart->lcr, UART_LCR_DLAB);
/* set baudrate */
out_8(&uart->rbr, combrd);
/* set data-format: 8-N-1 */
- out_8(&uart->lcr, LCR_WLS_8);
+ out_8(&uart->lcr, UART_LCR_WLS_8);
}
if (mode & 2) {
/* set request to send */
- out_8(&uart->mcr, MCR_RTS);
+ out_8(&uart->mcr, UART_MCR_RTS);
udelay(10);
/* check clear to send */
- if ((in_8(&uart->msr) & MSR_CTS) == 0x00)
+ if ((in_8(&uart->msr) & UART_MSR_CTS) == 0x00)
return -1;
}
if (mode & 4) {
/* set data terminal ready */
- out_8(&uart->mcr, MCR_DTR);
+ out_8(&uart->mcr, UART_MCR_DTR);
udelay(10);
/* check data set ready and carrier detect */
- if ((in_8(&uart->msr) & (MSR_DSR | MSR_DCD))
- != (MSR_DSR | MSR_DCD))
+ if ((in_8(&uart->msr) & (UART_MSR_DSR | UART_MSR_DCD))
+ != (UART_MSR_DSR | UART_MSR_DCD))
return -1;
}
/* write each message-character, read it back, and display it */
for (i = 0, len = strlen(argv[3]); i < len; ++i) {
j = 0;
- while ((in_8(&uart->lsr) & LSR_THRE) == 0x00) {
+ while ((in_8(&uart->lsr) & UART_LSR_THRE) == 0x00) {
if (j++ > CONFIG_SYS_HZ)
break;
udelay(10);
}
out_8(&uart->rbr, argv[3][i]);
j = 0;
- while ((in_8(&uart->lsr) & LSR_DR) == 0x00) {
+ while ((in_8(&uart->lsr) & UART_LSR_DR) == 0x00) {
if (j++ > CONFIG_SYS_HZ)
break;
udelay(10);
*/
AVR_port->lcr = 0x00;
AVR_port->ier = 0x00;
- AVR_port->lcr = LCR_BKSE;
+ AVR_port->lcr = UART_LCR_BKSE;
AVR_port->dll = clock_divisor & 0xff;
AVR_port->dlm = (clock_divisor >> 8) & 0xff;
- AVR_port->lcr = LCR_WLS_8 | LCR_PEN | LCR_EPS;
+ AVR_port->lcr = UART_LCR_WLS_8 | UART_LCR_PEN | UART_LCR_EPS;
AVR_port->mcr = 0x00;
- AVR_port->fcr = FCR_FIFO_EN | FCR_RXSR | FCR_TXSR;
+ AVR_port->fcr = UART_FCR_FIFO_EN | UART_FCR_RXSR | UART_FCR_TXSR;
miconCntl_DisWDT();
LIB = $(obj)lib$(BOARD).a
-COBJS := netstar.o flash.o nand.o
+COBJS := netstar.o
SOBJS := setup.o crcek.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) eeprom.c \
#include <sys/stat.h>
#include "crcek.h"
-extern unsigned long crc32(unsigned long, const unsigned char *, unsigned int);
+extern uint32_t crc32(uint32_t, const unsigned char *, uint);
-uint32_t data[LOADER_SIZE/4 + 3];
+static uint32_t data[LOADER_SIZE/4 + 3];
-int doit(char *path, unsigned version)
+static int do_crc(char *path, unsigned version)
{
uint32_t *p;
ssize_t size;
fprintf(stderr, "File too large\n");
return EXIT_FAILURE;
}
- size = (((size - 1) >> 2) + 1) << 2;
+ size = (size + 3) & ~3; /* round up to 4 bytes */
data[0] = size + 4; /* add size of version field */
data[1] = version;
- data[(size >> 2) + 2] = crc32(0, (unsigned char *)(data + 1), data[0]);
+ data[2 + (size >> 2)] = crc32(0, (unsigned char *)(data + 1), data[0]);
close(fd);
if (write(STDOUT_FILENO, data, size + 3*4) == -1) {
int main(int argc, char **argv)
{
if (argc == 2) {
- return doit(argv[1], 0);
+ return do_crc(argv[1], 0);
} else if ((argc == 4) && (strcmp(argv[1], "-v") == 0)) {
char *endptr, *nptr = argv[2];
unsigned ver = strtoul(nptr, &endptr, 0);
if (*nptr != '\0' && *endptr == '\0')
- return doit(argv[3], ver);
+ return do_crc(argv[3], ver);
}
fprintf(stderr, "Usage: crcit [-v version] <image>\n");
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Alex Zuepke <azu@sysgo.de>
- *
- * (C) Copyright 2005
- * 2N Telekomunikace, a.s. <www.2n.cz>
- * Ladislav Michl <michl@2n.cz>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-/*#if 0 */
-#if (PHYS_SDRAM_1_SIZE != SZ_32M)
-
-#include "crcek.h"
-
-#if (CONFIG_SYS_MAX_FLASH_BANKS > 1)
-#error There is always only _one_ flash chip
-#endif
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-#define CMD_READ_ARRAY 0x000000f0
-#define CMD_UNLOCK1 0x000000aa
-#define CMD_UNLOCK2 0x00000055
-#define CMD_ERASE_SETUP 0x00000080
-#define CMD_ERASE_CONFIRM 0x00000030
-#define CMD_PROGRAM 0x000000a0
-#define CMD_UNLOCK_BYPASS 0x00000020
-
-#define MEM_FLASH_ADDR1 (*(volatile u16 *)(CONFIG_SYS_FLASH_BASE + (0x00000555 << 1)))
-#define MEM_FLASH_ADDR2 (*(volatile u16 *)(CONFIG_SYS_FLASH_BASE + (0x000002aa << 1)))
-
-#define BIT_ERASE_DONE 0x00000080
-#define BIT_RDY_MASK 0x00000080
-#define BIT_PROGRAM_ERROR 0x00000020
-#define BIT_TIMEOUT 0x80000000 /* our flag */
-
-/*-----------------------------------------------------------------------
- */
-
-ulong flash_init(void)
-{
- int i;
-
- flash_info[0].flash_id = (AMD_MANUFACT & FLASH_VENDMASK) |
- (AMD_ID_LV800B & FLASH_TYPEMASK);
- flash_info[0].size = PHYS_FLASH_1_SIZE;
- flash_info[0].sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- memset(flash_info[0].protect, 0, CONFIG_SYS_MAX_FLASH_SECT);
-
- for (i = 0; i < flash_info[0].sector_count; i++) {
- switch (i) {
- case 0: /* 16kB */
- flash_info[0].start[0] = CONFIG_SYS_FLASH_BASE;
- break;
- case 1: /* 8kB */
- flash_info[0].start[1] = CONFIG_SYS_FLASH_BASE + 0x4000;
- break;
- case 2: /* 8kB */
- flash_info[0].start[2] = CONFIG_SYS_FLASH_BASE + 0x4000 +
- 0x2000;
- break;
- case 3: /* 32 KB */
- flash_info[0].start[3] = CONFIG_SYS_FLASH_BASE + 0x4000 +
- 2 * 0x2000;
- break;
- case 4:
- flash_info[0].start[4] = CONFIG_SYS_FLASH_BASE + 0x4000 +
- 2 * 0x2000 + 0x8000;
- break;
- default: /* 64kB */
- flash_info[0].start[i] = flash_info[0].start[i-1] +
- 0x10000;
- break;
- }
- }
-
- /* U-Boot */
- flash_protect(FLAG_PROTECT_SET,
- LOADER1_OFFSET,
- LOADER1_OFFSET + LOADER_SIZE - 1, flash_info);
- /* Protect crcek, env and r_env as well */
- flash_protect(FLAG_PROTECT_SET, 0, 0x8000 - 1, flash_info);
-
- return flash_info[0].size;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info(flash_info_t *info)
-{
- int i;
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case (AMD_MANUFACT & FLASH_VENDMASK):
- puts("AMD: ");
- break;
- default:
- puts("Unknown vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case (AMD_ID_LV800B & FLASH_TYPEMASK):
- puts("AM29LV800BB (8Mb)\n");
- break;
- default:
- puts("Unknown chip type\n");
- return;
- }
-
- printf(" Size: %ld MB in %d sectors\n",
- info->size >> 20, info->sector_count);
-
- puts(" Sector start addresses:");
- for (i = 0; i < info->sector_count; i++) {
- if ((i % 5) == 0)
- puts("\n ");
-
- printf(" %08lX%s", info->start[i],
- info->protect[i] ? " (RO)" : " ");
- }
- puts("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase(flash_info_t *info, int s_first, int s_last)
-{
- ushort result;
- int prot, sect;
- int rc = ERR_OK;
-
- /* first look for protection bits */
-
- if (info->flash_id == FLASH_UNKNOWN)
- return ERR_UNKNOWN_FLASH_TYPE;
-
- if ((s_first < 0) || (s_first > s_last))
- return ERR_INVAL;
-
- if ((info->flash_id & FLASH_VENDMASK) !=
- (AMD_MANUFACT & FLASH_VENDMASK))
- return ERR_UNKNOWN_FLASH_VENDOR;
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect)
- if (info->protect[sect])
- prot++;
-
- if (prot)
- printf("- Warning: %d protected sectors will not be erased!\n",
- prot);
- else
- putc('\n');
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last && !ctrlc (); sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- vu_short *addr = (vu_short *) (info->start[sect]);
-
- /* arm simple, non interrupt dependent timer */
- reset_timer_masked();
-
- MEM_FLASH_ADDR1 = CMD_UNLOCK1;
- MEM_FLASH_ADDR2 = CMD_UNLOCK2;
- MEM_FLASH_ADDR1 = CMD_ERASE_SETUP;
-
- MEM_FLASH_ADDR1 = CMD_UNLOCK1;
- MEM_FLASH_ADDR2 = CMD_UNLOCK2;
- *addr = CMD_ERASE_CONFIRM;
-
- /* wait until flash is ready */
- while (1) {
- result = *addr;
-
- /* check timeout */
- if (get_timer_masked() > CONFIG_SYS_FLASH_ERASE_TOUT) {
- MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
- rc = ERR_TIMOUT;
- break;
- }
-
- if ((result & 0xfff) & BIT_ERASE_DONE)
- break;
-
- if ((result & 0xffff) & BIT_PROGRAM_ERROR) {
- rc = ERR_PROG_ERROR;
- break;
- }
- }
-
- MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
-
- if (rc != ERR_OK)
- goto out;
-
- putc('.');
- }
- }
-out:
- /* allow flash to settle - wait 10 ms */
- udelay_masked(10000);
-
- return rc;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash
- */
-
-static int write_hword(flash_info_t *info, ulong dest, ushort data)
-{
- vu_short *addr = (vu_short *) dest;
- ushort result;
- int rc = ERR_OK;
-
- /* check if flash is (sufficiently) erased */
- result = *addr;
- if ((result & data) != data)
- return ERR_NOT_ERASED;
-
- MEM_FLASH_ADDR1 = CMD_UNLOCK1;
- MEM_FLASH_ADDR2 = CMD_UNLOCK2;
- MEM_FLASH_ADDR1 = CMD_PROGRAM;
- *addr = data;
-
- /* arm simple, non interrupt dependent timer */
- reset_timer_masked();
-
- /* wait until flash is ready */
- while (1) {
- result = *addr;
-
- /* check timeout */
- if (get_timer_masked () > CONFIG_SYS_FLASH_ERASE_TOUT) {
- rc = ERR_TIMOUT;
- break;
- }
-
- if ((result & 0x80) == (data & 0x80))
- break;
-
- if ((result & 0xffff) & BIT_PROGRAM_ERROR) {
- result = *addr;
-
- if ((result & 0x80) != (data & 0x80))
- rc = ERR_PROG_ERROR;
- }
- }
-
- *addr = CMD_READ_ARRAY;
-
- if (*addr != data)
- rc = ERR_PROG_ERROR;
-
- return rc;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash.
- */
-
-int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- int l;
- int i, rc;
- ushort data;
-
- wp = (addr & ~1); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp)
- data = (data >> 8) | (*(uchar *) cp << 8);
- for (; i < 2 && cnt > 0; ++i) {
- data = (data >> 8) | (*src++ << 8);
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < 2; ++i, ++cp)
- data = (data >> 8) | (*(uchar *) cp << 8);
-
- if ((rc = write_hword(info, wp, data)) != 0)
- return (rc);
- wp += 2;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 2) {
- data = *((vu_short *) src);
- if ((rc = write_hword(info, wp, data)) != 0)
- return (rc);
- src += 2;
- wp += 2;
- cnt -= 2;
- }
-
- if (cnt == 0)
- return ERR_OK;
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < 2 && cnt > 0; ++i, ++cp) {
- data = (data >> 8) | (*src++ << 8);
- --cnt;
- }
- for (; i < 2; ++i, ++cp)
- data = (data >> 8) | (*(uchar *) cp << 8);
-
- return write_hword(info, wp, data);
-}
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2005 2N TELEKOMUNIKACE, Ladislav Michl
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/io.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <nand.h>
-
-/*
- * hardware specific access to control-lines
- */
-#define MASK_CLE 0x02
-#define MASK_ALE 0x04
-
-static void netstar_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
- ulong IO_ADDR_W = (ulong) this->IO_ADDR_W;
-
- IO_ADDR_W &= ~(MASK_ALE|MASK_CLE);
- if (ctrl & NAND_CTRL_CHANGE) {
- if ( ctrl & NAND_CLE )
- IO_ADDR_W |= MASK_CLE;
- if ( ctrl & NAND_ALE )
- IO_ADDR_W |= MASK_ALE;
- }
- this->IO_ADDR_W = (void __iomem *) IO_ADDR_W;
-
- if (cmd != NAND_CMD_NONE)
- writeb(cmd, this->IO_ADDR_W);
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
- nand->options = NAND_SAMSUNG_LP_OPTIONS;
- nand->ecc.mode = NAND_ECC_SOFT;
- nand->cmd_ctrl = netstar_nand_hwcontrol;
- nand->chip_delay = 400;
- return 0;
-}
-#endif
*/
#include <common.h>
+#include <i2c.h>
+#include <flash.h>
+#include <nand.h>
+
+#include <asm/io.h>
DECLARE_GLOBAL_DATA_PTR;
int misc_init_r(void)
{
+#if defined(CONFIG_RTC_DS1307)
+ /* enable trickle charge */
+ i2c_reg_write(CONFIG_SYS_I2C_RTC_ADDR, 0x10, 0xaa);
+#endif
return 0;
}
{
return 0;
}
+
+#if defined(CONFIG_CMD_FLASH)
+ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t * info)
+{
+ if (banknum == 0) { /* AM29LV800 boot flash */
+ info->portwidth = FLASH_CFI_16BIT;
+ info->chipwidth = FLASH_CFI_BY16;
+ info->interface = FLASH_CFI_X16;
+ return 1;
+ }
+
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_CMD_NAND)
+/*
+ * hardware specific access to control-lines
+ *
+ * NAND_NCE: bit 0 - don't care
+ * NAND_CLE: bit 1 -> bit 1 (0x0002)
+ * NAND_ALE: bit 2 -> bit 2 (0x0004)
+ */
+static void netstar_nand_hwcontrol(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *chip = mtd->priv;
+ unsigned long mask;
+
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+ if (ctrl & NAND_ALE)
+ mask |= 0x04;
+ writeb(cmd, (unsigned long)chip->IO_ADDR_W | mask);
+}
+
+int board_nand_init(struct nand_chip *nand)
+{
+ nand->options = NAND_SAMSUNG_LP_OPTIONS;
+ nand->ecc.mode = NAND_ECC_SOFT;
+ nand->cmd_ctrl = netstar_nand_hwcontrol;
+ nand->chip_delay = 400;
+ return 0;
+}
+#endif
rcode = do_bootm (cmdtp, 0, 1, local_args);
}
-#ifdef CONFIG_AUTOSCRIPT
+#ifdef CONFIG_SOURCE
if (load_addr) {
char *s;
if (((s = getenv("autoscript")) != NULL) && (strcmp(s,"yes") == 0)) {
- printf ("Running autoscript at addr 0x%08lX", load_addr);
+ printf ("Running "source" command at addr 0x%08lX",
+ load_addr);
s = getenv ("autoscript_uname");
if (s)
else
puts (" ...\n");
- rcode = autoscript (load_addr, s);
+ rcode = source (load_addr, s);
}
}
#endif
# command
COBJS-$(CONFIG_CMD_AMBAPP) += cmd_ambapp.o
-COBJS-$(CONFIG_AUTOSCRIPT) += cmd_autoscript.o
-COBJS-$(CONFIG_CMD_AUTOSCRIPT) += cmd_autoscript.o
+COBJS-$(CONFIG_SOURCE) += cmd_source.o
+COBJS-$(CONFIG_CMD_SOURCE) += cmd_source.o
COBJS-$(CONFIG_CMD_BDI) += cmd_bdinfo.o
COBJS-$(CONFIG_CMD_BEDBUG) += bedbug.o cmd_bedbug.o
COBJS-$(CONFIG_CMD_BMP) += cmd_bmp.o
}
}
-#ifdef CONFIG_AUTOSCRIPT
+#ifdef CONFIG_SOURCE
if (load_addr) {
char *s;
if (((s = getenv("autoscript")) != NULL) && (strcmp(s,"yes") == 0)) {
- printf ("Running autoscript at addr 0x%08lX", load_addr);
+ printf ("Running "source" command at addr 0x%08lX",
+ load_addr);
s = getenv ("autoscript_uname");
if (s)
else
puts (" ...\n");
- rcode = autoscript (load_addr, s);
+ rcode = source (load_addr, s);
}
}
#endif
rcode = do_bootm (cmdtp, 0, 1, local_args);
}
-#ifdef CONFIG_AUTOSCRIPT
+#ifdef CONFIG_SOURCE
if (((s = getenv("autoscript")) != NULL) && (strcmp(s,"yes") == 0)) {
- printf ("Running autoscript at addr 0x%08lX", load_addr);
+ printf ("Running "source" command at addr 0x%08lX",
+ load_addr);
s = getenv ("autoscript_uname");
if (s)
puts (" ...\n");
show_boot_progress (83);
- rcode = autoscript (load_addr, s);
+ rcode = source (load_addr, s);
}
#endif
if (rcode < 0)
*/
/*
- * autoscript allows a remote host to download a command file and,
- * optionally, binary data for automatically updating the target. For
- * example, you create a new kernel image and want the user to be
- * able to simply download the image and the machine does the rest.
- * The kernel image is postprocessed with mkimage, which creates an
- * image with a script file prepended. If enabled, autoscript will
- * verify the script and contents of the download and execute the
- * script portion. This would be responsible for erasing flash,
- * copying the new image, and rebooting the machine.
+ * The "source" command allows to define "script images", i. e. files
+ * that contain command sequences that can be executed by the command
+ * interpreter. It returns the exit status of the last command
+ * executed from the script. This is very similar to running a shell
+ * script in a UNIX shell, hence the name for the command.
*/
/* #define DEBUG */
#endif
int
-autoscript (ulong addr, const char *fit_uname)
+source (ulong addr, const char *fit_uname)
{
ulong len;
image_header_t *hdr;
break;
#endif
default:
- puts ("Wrong image format for autoscript\n");
+ puts ("Wrong image format for \"source\" command\n");
return 1;
}
}
/**************************************************/
-#if defined(CONFIG_CMD_AUTOSCRIPT)
+#if defined(CONFIG_CMD_SOURCE)
int
-do_autoscript (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+do_source (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
ulong addr;
int rcode;
/* Find script image */
if (argc < 2) {
addr = CONFIG_SYS_LOAD_ADDR;
- debug ("* autoscr: default load address = 0x%08lx\n", addr);
+ debug ("* source: default load address = 0x%08lx\n", addr);
#if defined(CONFIG_FIT)
} else if (fit_parse_subimage (argv[1], load_addr, &addr, &fit_uname)) {
- debug ("* autoscr: subimage '%s' from FIT image at 0x%08lx\n",
+ debug ("* source: subimage '%s' from FIT image at 0x%08lx\n",
fit_uname, addr);
#endif
} else {
addr = simple_strtoul(argv[1], NULL, 16);
- debug ("* autoscr: cmdline image address = 0x%08lx\n", addr);
+ debug ("* source: cmdline image address = 0x%08lx\n", addr);
}
printf ("## Executing script at %08lx\n", addr);
- rcode = autoscript (addr, fit_uname);
+ rcode = source (addr, fit_uname);
return rcode;
}
U_BOOT_CMD(
- autoscr, 2, 0, do_autoscript,
+ source, 2, 0, do_source,
"run script from memory",
- "[addr] - run script starting at addr"
- " - A valid autoscr header must be present\n"
+ "[addr]\n"
+ "\t- run script starting at addr\n"
+ "\t- A valid image header must be present\n"
#if defined(CONFIG_FIT)
"For FIT format uImage addr must include subimage\n"
"unit name in the form of addr:<subimg_uname>\n"
#endif
);
+
+/*
+ * Keep for now for backward compatibility;
+ * remove later when support for "autoscr" goes away.
+ */
+static int
+do_autoscr (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ printf ("\n### WARNING ### "
+ "\"autoscr\" is deprecated, use \"source\" instead ###\n\n");
+ return do_source (cmdtp, flag, argc, argv);
+}
+
+U_BOOT_CMD(
+ autoscr, 2, 0, do_autoscr,
+ "DEPRECATED - use \"source\" command instead",
+ "DEPRECATED - use \"source\" command instead\n"
+);
#endif
LIB = $(obj)lib$(SOC).a
-COBJS = interrupts.o serial.o generic.o
+COBJS = interrupts.o generic.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
/* Start the counter ticking up */
*((int32_t *) (CONFIG_SYS_TIMERBASE + TLDR)) = TIMER_LOAD_VAL; /* reload value on overflow*/
- val = (CONFIG_SYS_PVT << 2) | BIT5 | BIT1 | BIT0; /* mask to enable timer*/
+ val = (CONFIG_SYS_PTV << 2) | BIT5 | BIT1 | BIT0; /* mask to enable timer*/
*((int32_t *) (CONFIG_SYS_TIMERBASE + TCLR)) = val; /* start timer */
reset_timer_masked(); /* init the timestamp and lastinc value */
COBJS-y = interrupts.o
COBJS-$(CONFIG_S3C6400) += cpu_init.o speed.o
-COBJS-$(CONFIG_USB_OHCI_NEW) += usb.o
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS-y))
LIB = $(obj)lib$(CPU).a
START = start.o
-COBJS = serial.o serial_netarm.o interrupts.o cpu.o
+COBJS = interrupts.o cpu.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
{
return (read_p15_c1 () & C1_IDC) != 0;
}
-
-#elif defined(CONFIG_S3C4510B)
-
-void icache_enable (void)
-{
- s32 i;
-
- /* disable all cache bits */
- CLR_REG( REG_SYSCFG, 0x3F);
-
- /* 8KB cache, write enable */
- SET_REG( REG_SYSCFG, CACHE_WRITE_BUFF | CACHE_MODE_01);
-
- /* clear TAG RAM bits */
- for ( i = 0; i < 256; i++)
- PUT_REG( CACHE_TAG_RAM + 4*i, 0x00000000);
-
- /* clear SET0 RAM */
- for(i=0; i < 1024; i++)
- PUT_REG( CACHE_SET0_RAM + 4*i, 0x00000000);
-
- /* clear SET1 RAM */
- for(i=0; i < 1024; i++)
- PUT_REG( CACHE_SET1_RAM + 4*i, 0x00000000);
-
- /* enable cache */
- SET_REG( REG_SYSCFG, CACHE_ENABLE);
-
-}
-
-void icache_disable (void)
-{
- /* disable all cache bits */
- CLR_REG( REG_SYSCFG, 0x3F);
-}
-
-int icache_status (void)
-{
- return GET_REG( REG_SYSCFG) & CACHE_ENABLE;
-}
-
-void dcache_enable (void)
-{
- /* we don't have seperate instruction/data caches */
- icache_enable();
-}
-
-void dcache_disable (void)
-{
- /* we don't have seperate instruction/data caches */
- icache_disable();
-}
-
-int dcache_status (void)
-{
- /* we don't have seperate instruction/data caches */
- return icache_status();
-}
-
#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
/* No specific cache setup for IntegratorAP/CM720T as yet */
void icache_enable (void)
{
}
-#elif defined(CONFIG_LPC2292) /* just to satisfy the compiler */
-#else
-#error No icache/dcache enable/disable functions defined for this CPU type
#endif
--- /dev/null
+#
+# (C) Copyright 2000-2008
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(SOC).a
+
+COBJS-y += cache.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS-y))
+
+all: $(obj).depend $(LIB)
+
+$(LIB): $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
+
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/hardware.h>
+
+void icache_enable (void)
+{
+ s32 i;
+
+ /* disable all cache bits */
+ CLR_REG( REG_SYSCFG, 0x3F);
+
+ /* 8KB cache, write enable */
+ SET_REG( REG_SYSCFG, CACHE_WRITE_BUFF | CACHE_MODE_01);
+
+ /* clear TAG RAM bits */
+ for ( i = 0; i < 256; i++)
+ PUT_REG( CACHE_TAG_RAM + 4*i, 0x00000000);
+
+ /* clear SET0 RAM */
+ for(i=0; i < 1024; i++)
+ PUT_REG( CACHE_SET0_RAM + 4*i, 0x00000000);
+
+ /* clear SET1 RAM */
+ for(i=0; i < 1024; i++)
+ PUT_REG( CACHE_SET1_RAM + 4*i, 0x00000000);
+
+ /* enable cache */
+ SET_REG( REG_SYSCFG, CACHE_ENABLE);
+
+}
+
+void icache_disable (void)
+{
+ /* disable all cache bits */
+ CLR_REG( REG_SYSCFG, 0x3F);
+}
+
+int icache_status (void)
+{
+ return GET_REG( REG_SYSCFG) & CACHE_ENABLE;
+}
+
+void dcache_enable (void)
+{
+ /* we don't have seperate instruction/data caches */
+ icache_enable();
+}
+
+void dcache_disable (void)
+{
+ /* we don't have seperate instruction/data caches */
+ icache_disable();
+}
+
+int dcache_status (void)
+{
+ /* we don't have seperate instruction/data caches */
+ return icache_status();
+}
LIB = $(obj)lib$(SOC).a
-COBJS = generic.o interrupts.o serial.o speed.o
+COBJS = generic.o interrupts.o speed.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
LIB = $(obj)lib$(SOC).a
-COBJS = interrupts.o serial.o
+COBJS = interrupts.o
SOBJS = lowlevel_init.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
LIB = $(obj)lib$(SOC).a
-COBJS = i2c.o interrupts.o serial.o speed.o \
- usb.o usb_ohci.o nand.o
+COBJS = interrupts.o speed.o usb.o usb_ohci.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
#include <common.h>
#include <arm925t.h>
#include <configs/omap1510.h>
+#include <asm/io.h>
#define TIMER_LOAD_VAL 0xffffffff
-/* macro to read the 32 bit timer */
-#define READ_TIMER (*(volatile ulong *)(CONFIG_SYS_TIMERBASE+8))
-
-static ulong timestamp;
-static ulong lastdec;
+static uint32_t timestamp;
+static uint32_t lastdec;
/* nothing really to do with interrupts, just starts up a counter. */
int interrupt_init (void)
{
- int32_t val;
-
/* Start the decrementer ticking down from 0xffffffff */
- *((int32_t *) (CONFIG_SYS_TIMERBASE + LOAD_TIM)) = TIMER_LOAD_VAL;
- val = MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE | (CONFIG_SYS_PVT << MPUTIM_PTV_BIT);
- *((int32_t *) (CONFIG_SYS_TIMERBASE + CNTL_TIMER)) = val;
+ __raw_writel(TIMER_LOAD_VAL, CONFIG_SYS_TIMERBASE + LOAD_TIM);
+ __raw_writel(MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE |
+ (CONFIG_SYS_PTV << MPUTIM_PTV_BIT),
+ CONFIG_SYS_TIMERBASE + CNTL_TIMER);
/* init the timestamp and lastdec value */
reset_timer_masked();
- return (0);
+ return 0;
}
/*
{
ulong tmo, tmp;
- if(usec >= 1000){ /* if "big" number, spread normalization to seconds */
+ if (usec >= 1000) { /* if "big" number, spread normalization to seconds */
tmo = usec / 1000; /* start to normalize for usec to ticks per sec */
- tmo *= CONFIG_SYS_HZ; /* find number of "ticks" to wait to achieve target */
+ tmo *= CONFIG_SYS_HZ; /* find number of "ticks" to wait to achieve target */
tmo /= 1000; /* finish normalize. */
- }else{ /* else small number, don't kill it prior to HZ multiply */
+ } else { /* else small number, don't kill it prior to HZ multiply */
tmo = usec * CONFIG_SYS_HZ;
tmo /= (1000*1000);
}
tmp = get_timer (0); /* get current timestamp */
- if( (tmo + tmp + 1) < tmp ) /* if setting this fordward will roll time stamp */
+ if ((tmo + tmp + 1) < tmp) /* if setting this fordward will roll time stamp */
reset_timer_masked (); /* reset "advancing" timestamp to 0, set lastdec value */
else
tmo += tmp; /* else, set advancing stamp wake up time */
void reset_timer_masked (void)
{
/* reset time */
- lastdec = READ_TIMER; /* capure current decrementer value time */
+ lastdec = __raw_readl(CONFIG_SYS_TIMERBASE + READ_TIM);
timestamp = 0; /* start "advancing" time stamp from 0 */
}
ulong get_timer_masked (void)
{
- ulong now = READ_TIMER; /* current tick value */
+ uint32_t now = __raw_readl(CONFIG_SYS_TIMERBASE + READ_TIM);
if (lastdec >= now) { /* normal mode (non roll) */
/* normal mode */
#ifdef CONFIG_INNOVATOROMAP1510
#define LOOPS_PER_MSEC 60 /* tuned on omap1510 */
volatile int i, time_remaining = LOOPS_PER_MSEC*usec;
- for (i=time_remaining; i>0; i--) { }
+ for (i=time_remaining; i>0; i--) { }
#else
ulong tmo;
if (usec >= 1000) { /* if "big" number, spread normalization to seconds */
tmo = usec / 1000; /* start to normalize for usec to ticks per sec */
- tmo *= CONFIG_SYS_HZ; /* find number of "ticks" to wait to achieve target */
+ tmo *= CONFIG_SYS_HZ; /* find number of "ticks" to wait to achieve target */
tmo /= 1000; /* finish normalize. */
} else { /* else small number, don't kill it prior to HZ multiply */
tmo = usec * CONFIG_SYS_HZ;
*/
ulong get_tbclk (void)
{
- ulong tbclk;
-
- tbclk = CONFIG_SYS_HZ;
- return tbclk;
+ return CONFIG_SYS_HZ;
}
LIB = $(obj)lib$(SOC).a
-COBJS = timer.o ether.o lxt972.o dp83848.o i2c.o nand.o
+COBJS = timer.o ether.o lxt972.o dp83848.o
SOBJS = lowlevel_init.o reset.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
/* Start the decrementer ticking down from 0xffffffff */
*((int32_t *) (CONFIG_SYS_TIMERBASE + LOAD_TIM)) = TIMER_LOAD_VAL;
- val = MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE | (CONFIG_SYS_PVT << MPUTIM_PTV_BIT);
+ val = MPUTIM_ST | MPUTIM_AR | MPUTIM_CLOCK_ENABLE | (CONFIG_SYS_PTV << MPUTIM_PTV_BIT);
*((int32_t *) (CONFIG_SYS_TIMERBASE + CNTL_TIMER)) = val;
/* init the timestamp and lastdec value */
/* start the counter ticking up, reload value on overflow */
writel(TIMER_LOAD_VAL, &timer_base->tldr);
/* enable timer */
- writel((CONFIG_SYS_PVT << 2) | TCLR_PRE | TCLR_AR | TCLR_ST,
+ writel((CONFIG_SYS_PTV << 2) | TCLR_PRE | TCLR_AR | TCLR_ST,
&timer_base->tclr);
reset_timer_masked(); /* init the timestamp and lastinc value */
LIB = $(obj)lib$(CPU).a
START = start.o
-COBJS = serial.o interrupts.o cpu.o
+COBJS = cache.o cpu.o interrupts.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * DAVE Srl
+ * http://www.dave-tech.it
+ * http://www.wawnet.biz
+ * mailto:info@wawnet.biz
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/hardware.h>
+
+static void s3c44b0_flush_cache(void)
+{
+ volatile int i;
+ /* flush cycle */
+ for(i=0x10002000;i<0x10004800;i+=16)
+ {
+ *((int *)i)=0x0;
+ }
+}
+
+void icache_enable (void)
+{
+ ulong reg;
+
+ s3c44b0_flush_cache();
+
+ /*
+ Init cache
+ Non-cacheable area (everything outside RAM)
+ 0x0000:0000 - 0x0C00:0000
+ */
+ NCACHBE0 = 0xC0000000;
+ NCACHBE1 = 0x00000000;
+
+ /*
+ Enable chache
+ */
+ reg = SYSCFG;
+ reg |= 0x00000006; /* 8kB */
+ SYSCFG = reg;
+}
+
+void icache_disable (void)
+{
+ ulong reg;
+
+ reg = SYSCFG;
+ reg &= ~0x00000006; /* 8kB */
+ SYSCFG = reg;
+}
+
+int icache_status (void)
+{
+ return 0;
+}
+
+void dcache_enable (void)
+{
+ icache_enable();
+}
+
+void dcache_disable (void)
+{
+ icache_disable();
+}
+
+int dcache_status (void)
+{
+ return dcache_status();
+}
+
#include <command.h>
#include <asm/hardware.h>
-static void s3c44b0_flush_cache(void)
-{
- volatile int i;
- /* flush cycle */
- for(i=0x10002000;i<0x10004800;i+=16)
- {
- *((int *)i)=0x0;
- }
-}
-
-
int cpu_init (void)
{
icache_enable();
/*NOTREACHED*/
return (0);
}
-
-void icache_enable (void)
-{
- ulong reg;
-
- s3c44b0_flush_cache();
-
- /*
- Init cache
- Non-cacheable area (everything outside RAM)
- 0x0000:0000 - 0x0C00:0000
- */
- NCACHBE0 = 0xC0000000;
- NCACHBE1 = 0x00000000;
-
- /*
- Enable chache
- */
- reg = SYSCFG;
- reg |= 0x00000006; /* 8kB */
- SYSCFG = reg;
-}
-
-void icache_disable (void)
-{
- ulong reg;
-
- reg = SYSCFG;
- reg &= ~0x00000006; /* 8kB */
- SYSCFG = reg;
-}
-
-int icache_status (void)
-{
- return 0;
-}
-
-void dcache_enable (void)
-{
- icache_enable();
-}
-
-void dcache_disable (void)
-{
- icache_disable();
-}
-
-int dcache_status (void)
-{
- return dcache_status();
-}
-
-/*
- RTC stuff
-*/
-#include <rtc.h>
-#ifndef BCD2HEX
- #define BCD2HEX(n) ((n>>4)*10+(n&0x0f))
-#endif
-#ifndef HEX2BCD
- #define HEX2BCD(x) ((((x) / 10) << 4) + (x) % 10)
-#endif
-
-int rtc_get (struct rtc_time* tm)
-{
- RTCCON |= 1;
- tm->tm_year = BCD2HEX(BCDYEAR);
- tm->tm_mon = BCD2HEX(BCDMON);
- tm->tm_wday = BCD2HEX(BCDDATE);
- tm->tm_mday = BCD2HEX(BCDDAY);
- tm->tm_hour = BCD2HEX(BCDHOUR);
- tm->tm_min = BCD2HEX(BCDMIN);
- tm->tm_sec = BCD2HEX(BCDSEC);
-
- if (tm->tm_sec==0) {
- /* we have to re-read the rtc data because of the "one second deviation" problem */
- /* see RTC datasheet for more info about it */
- tm->tm_year = BCD2HEX(BCDYEAR);
- tm->tm_mon = BCD2HEX(BCDMON);
- tm->tm_mday = BCD2HEX(BCDDAY);
- tm->tm_wday = BCD2HEX(BCDDATE);
- tm->tm_hour = BCD2HEX(BCDHOUR);
- tm->tm_min = BCD2HEX(BCDMIN);
- tm->tm_sec = BCD2HEX(BCDSEC);
- }
-
- RTCCON &= ~1;
-
- if(tm->tm_year >= 70)
- tm->tm_year += 1900;
- else
- tm->tm_year += 2000;
-
- return 0;
-}
-
-int rtc_set (struct rtc_time* tm)
-{
- if(tm->tm_year < 2000)
- tm->tm_year -= 1900;
- else
- tm->tm_year -= 2000;
-
- RTCCON |= 1;
- BCDYEAR = HEX2BCD(tm->tm_year);
- BCDMON = HEX2BCD(tm->tm_mon);
- BCDDAY = HEX2BCD(tm->tm_mday);
- BCDDATE = HEX2BCD(tm->tm_wday);
- BCDHOUR = HEX2BCD(tm->tm_hour);
- BCDMIN = HEX2BCD(tm->tm_min);
- BCDSEC = HEX2BCD(tm->tm_sec);
- RTCCON &= 1;
-
- return 0;
-}
-
-void rtc_reset (void)
-{
- RTCCON |= 1;
- BCDYEAR = 0;
- BCDMON = 0;
- BCDDAY = 0;
- BCDDATE = 0;
- BCDHOUR = 0;
- BCDMIN = 0;
- BCDSEC = 0;
- RTCCON &= 1;
-}
-
-
-/*
- I2C stuff
-*/
-
-/*
- * Initialization, must be called once on start up, may be called
- * repeatedly to change the speed and slave addresses.
- */
-void i2c_init(int speed, int slaveaddr)
-{
- /*
- setting up I2C support
- */
- unsigned int save_F,save_PF,rIICCON,rPCONA,rPDATA,rPCONF,rPUPF;
-
- save_F = PCONF;
- save_PF = PUPF;
-
- rPCONF = ((save_F & ~(0xF))| 0xa);
- rPUPF = (save_PF | 0x3);
- PCONF = rPCONF; /*PF0:IICSCL, PF1:IICSDA*/
- PUPF = rPUPF; /* Disable pull-up */
-
- /* Configuring pin for WC pin of EEprom */
- rPCONA = PCONA;
- rPCONA &= ~(1<<9);
- PCONA = rPCONA;
-
- rPDATA = PDATA;
- rPDATA &= ~(1<<9);
- PDATA = rPDATA;
-
- /*
- Enable ACK, IICCLK=MCLK/16, enable interrupt
- 75MHz/16/(12+1) = 390625 Hz
- */
- rIICCON=(1<<7)|(0<<6)|(1<<5)|(0xC);
- IICCON = rIICCON;
-
- IICADD = slaveaddr;
-}
-
-/*
- * Probe the given I2C chip address. Returns 0 if a chip responded,
- * not 0 on failure.
- */
-int i2c_probe(uchar chip)
-{
- /*
- not implemented
- */
-
- printf("i2c_probe chip %d\n", (int) chip);
- return -1;
-}
-
-/*
- * Read/Write interface:
- * chip: I2C chip address, range 0..127
- * addr: Memory (register) address within the chip
- * alen: Number of bytes to use for addr (typically 1, 2 for larger
- * memories, 0 for register type devices with only one
- * register)
- * buffer: Where to read/write the data
- * len: How many bytes to read/write
- *
- * Returns: 0 on success, not 0 on failure
- */
-
-#define S3C44B0X_rIIC_INTPEND (1<<4)
-#define S3C44B0X_rIIC_LAST_RECEIV_BIT (1<<0)
-#define S3C44B0X_rIIC_INTERRUPT_ENABLE (1<<5)
-#define S3C44B0_IIC_TIMEOUT 100
-
-int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
-
- int k, j, temp;
- u32 rIICSTAT;
-
- /*
- send the device offset
- */
-
- rIICSTAT = 0xD0;
- IICSTAT = rIICSTAT;
-
- IICDS = chip; /* this is a write operation... */
-
- rIICSTAT |= (1<<5);
- IICSTAT = rIICSTAT;
-
- for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
- temp = IICCON;
- if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
- break;
- udelay(2000);
- }
- if (k==S3C44B0_IIC_TIMEOUT)
- return -1;
-
- /* wait and check ACK */
- temp = IICSTAT;
- if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
- return -1;
-
- IICDS = addr;
- IICCON = IICCON & ~(S3C44B0X_rIIC_INTPEND);
-
- /* wait and check ACK */
- for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
- temp = IICCON;
- if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
- break;
- udelay(2000);
- }
- if (k==S3C44B0_IIC_TIMEOUT)
- return -1;
-
- temp = IICSTAT;
- if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
- return -1;
-
- /*
- now we can start with the read operation...
- */
-
- IICDS = chip | 0x01; /* this is a read operation... */
-
- rIICSTAT = 0x90; /*master recv*/
- rIICSTAT |= (1<<5);
- IICSTAT = rIICSTAT;
-
- IICCON = IICCON & ~(S3C44B0X_rIIC_INTPEND);
-
- /* wait and check ACK */
- for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
- temp = IICCON;
- if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
- break;
- udelay(2000);
- }
- if (k==S3C44B0_IIC_TIMEOUT)
- return -1;
-
- temp = IICSTAT;
- if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
- return -1;
-
- for (j=0; j<len-1; j++) {
-
- /*clear pending bit to resume */
-
- temp = IICCON & ~(S3C44B0X_rIIC_INTPEND);
- IICCON = temp;
-
- /* wait and check ACK */
- for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
- temp = IICCON;
- if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
- break;
- udelay(2000);
- }
- if (k==S3C44B0_IIC_TIMEOUT)
- return -1;
-
-
- buffer[j] = IICDS; /*save readed data*/
-
- } /*end for(j)*/
-
- /*
- reading the last data
- unset ACK generation
- */
- temp = IICCON & ~(S3C44B0X_rIIC_INTPEND | (1<<7));
- IICCON = temp;
-
- /* wait but NOT check ACK */
- for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
- temp = IICCON;
- if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
- break;
- udelay(2000);
- }
- if (k==S3C44B0_IIC_TIMEOUT)
- return -1;
-
- buffer[j] = IICDS; /*save readed data*/
-
- rIICSTAT = 0x90; /*master recv*/
-
- /* Write operation Terminate sending STOP */
- IICSTAT = rIICSTAT;
- /*Clear Int Pending Bit to RESUME*/
- temp = IICCON;
- IICCON = temp & (~S3C44B0X_rIIC_INTPEND);
-
- IICCON = IICCON | (1<<7); /*restore ACK generation*/
-
- return 0;
-}
-
-int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
-{
- int j, k;
- u32 rIICSTAT, temp;
-
-
- /*
- send the device offset
- */
-
- rIICSTAT = 0xD0;
- IICSTAT = rIICSTAT;
-
- IICDS = chip; /* this is a write operation... */
-
- rIICSTAT |= (1<<5);
- IICSTAT = rIICSTAT;
-
- IICCON = IICCON & ~(S3C44B0X_rIIC_INTPEND);
-
- /* wait and check ACK */
- for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
- temp = IICCON;
- if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
- break;
- udelay(2000);
- }
- if (k==S3C44B0_IIC_TIMEOUT)
- return -1;
-
- temp = IICSTAT;
- if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
- return -1;
-
- IICDS = addr;
- IICCON = IICCON & ~(S3C44B0X_rIIC_INTPEND);
-
- /* wait and check ACK */
- for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
- temp = IICCON;
- if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
- break;
- udelay(2000);
- }
- if (k==S3C44B0_IIC_TIMEOUT)
- return -1;
-
- temp = IICSTAT;
- if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
- return -1;
-
- /*
- now we can start with the read write operation
- */
- for (j=0; j<len; j++) {
-
- IICDS = buffer[j]; /*prerare data to write*/
-
- /*clear pending bit to resume*/
-
- temp = IICCON & ~(S3C44B0X_rIIC_INTPEND);
- IICCON = temp;
-
- /* wait but NOT check ACK */
- for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
- temp = IICCON;
- if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
- break;
-
- udelay(2000);
- }
-
- if (k==S3C44B0_IIC_TIMEOUT)
- return -1;
-
- } /* end for(j) */
-
- /* sending stop to terminate */
- rIICSTAT = 0xD0; /*master send*/
- IICSTAT = rIICSTAT;
- /*Clear Int Pending Bit to RESUME*/
- temp = IICCON;
- IICCON = temp & (~S3C44B0X_rIIC_INTPEND);
-
- return 0;
-}
LIB = $(obj)lib$(CPU).a
START = start.o
-COBJS = serial.o interrupts.o cpu.o
+COBJS = interrupts.o cpu.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
---------------------------
What: "autoscr" command
-When: August 2009
-Why: "autosrc" is an ugly and completely non-standard name. The "autoscr"
- command is deprecated and will be replaced the "source" command as
- used by other shells such as bash. Both commands will be supported
- for a transition period of 6 months after which "autoscr" will be
- removed.
+When: Release 2009-09
+
+Why: "autosrc" is an ugly and completely non-standard name.
+ The "autoscr" command is deprecated and will be replaced by
+
+ the "source" command as used by other shells such as bash.
+
+ Starting with March 2009, both commands will be supported for
+ a transition period of 6 months after which "autoscr" will be
+ removed. During the transition period existing scripts and
+ environment variable names remain untouched for maximum
+ compatibiltiy; thse will be changed when support for the
+ "autoscr" command get's finally dropped.
+
Who: Peter Tyser <ptyser@xes-inc.com>
---------------------------
+What: GPL cleanup
+When: August 2009
+Why: Over time, a couple of files have sneaked in into the U-Boot
+ source code that are either missing a valid GPL license
+ header or that carry a license that is incompatible with the
+ GPL.
+ Such files shall be removed from the U-Boot source tree.
+ See http://www.denx.de/wiki/pub/U-Boot/TaskGplCleanup/u-boot-1.1.2-files
+ for an old and probably incomplete list of such files.
+
+Who: Wolfgang Denk <wd@denx.de> and board maintainers
+
+---------------------------
+
What: Individual I2C commands
When: April 2009
Why: Per the U-Boot README, individual I2C commands such as "imd", "imm",
LIB := $(obj)libi2c.a
COBJS-$(CONFIG_BFIN_TWI_I2C) += bfin-twi_i2c.o
+COBJS-$(CONFIG_DRIVER_DAVINCI_I2C) += davinci_i2c.o
COBJS-$(CONFIG_FSL_I2C) += fsl_i2c.o
COBJS-$(CONFIG_I2C_MXC) += mxc_i2c.o
COBJS-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o
COBJS-$(CONFIG_DRIVER_OMAP24XX_I2C) += omap24xx_i2c.o
COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += omap24xx_i2c.o
+COBJS-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
+COBJS-$(CONFIG_S3C44B0_I2C) += s3c44b0_i2c.o
COBJS-$(CONFIG_SOFT_I2C) += soft_i2c.o
COBJS-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
*/
#include <common.h>
-
-#ifdef CONFIG_DRIVER_DAVINCI_I2C
-
#include <i2c.h>
#include <asm/arch/hardware.h>
#include <asm/arch/i2c_defs.h>
return(0);
}
-
-#endif /* CONFIG_DRIVER_DAVINCI_I2C */
*/
#include <common.h>
-
-#ifdef CONFIG_DRIVER_S3C24X0_I2C
-
#if defined(CONFIG_S3C2400)
#include <s3c2400.h>
#elif defined(CONFIG_S3C2410)
len) != 0);
}
#endif /* CONFIG_HARD_I2C */
-
-#endif /* CONFIG_DRIVER_S3C24X0_I2C */
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * DAVE Srl
+ * http://www.dave-tech.it
+ * http://www.wawnet.biz
+ * mailto:info@wawnet.biz
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/hardware.h>
+
+/*
+ * Initialization, must be called once on start up, may be called
+ * repeatedly to change the speed and slave addresses.
+ */
+void i2c_init(int speed, int slaveaddr)
+{
+ /*
+ setting up I2C support
+ */
+ unsigned int save_F,save_PF,rIICCON,rPCONA,rPDATA,rPCONF,rPUPF;
+
+ save_F = PCONF;
+ save_PF = PUPF;
+
+ rPCONF = ((save_F & ~(0xF))| 0xa);
+ rPUPF = (save_PF | 0x3);
+ PCONF = rPCONF; /*PF0:IICSCL, PF1:IICSDA*/
+ PUPF = rPUPF; /* Disable pull-up */
+
+ /* Configuring pin for WC pin of EEprom */
+ rPCONA = PCONA;
+ rPCONA &= ~(1<<9);
+ PCONA = rPCONA;
+
+ rPDATA = PDATA;
+ rPDATA &= ~(1<<9);
+ PDATA = rPDATA;
+
+ /*
+ Enable ACK, IICCLK=MCLK/16, enable interrupt
+ 75MHz/16/(12+1) = 390625 Hz
+ */
+ rIICCON=(1<<7)|(0<<6)|(1<<5)|(0xC);
+ IICCON = rIICCON;
+
+ IICADD = slaveaddr;
+}
+
+/*
+ * Probe the given I2C chip address. Returns 0 if a chip responded,
+ * not 0 on failure.
+ */
+int i2c_probe(uchar chip)
+{
+ /*
+ not implemented
+ */
+
+ printf("i2c_probe chip %d\n", (int) chip);
+ return -1;
+}
+
+/*
+ * Read/Write interface:
+ * chip: I2C chip address, range 0..127
+ * addr: Memory (register) address within the chip
+ * alen: Number of bytes to use for addr (typically 1, 2 for larger
+ * memories, 0 for register type devices with only one
+ * register)
+ * buffer: Where to read/write the data
+ * len: How many bytes to read/write
+ *
+ * Returns: 0 on success, not 0 on failure
+ */
+
+#define S3C44B0X_rIIC_INTPEND (1<<4)
+#define S3C44B0X_rIIC_LAST_RECEIV_BIT (1<<0)
+#define S3C44B0X_rIIC_INTERRUPT_ENABLE (1<<5)
+#define S3C44B0_IIC_TIMEOUT 100
+
+int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
+{
+
+ int k, j, temp;
+ u32 rIICSTAT;
+
+ /*
+ send the device offset
+ */
+
+ rIICSTAT = 0xD0;
+ IICSTAT = rIICSTAT;
+
+ IICDS = chip; /* this is a write operation... */
+
+ rIICSTAT |= (1<<5);
+ IICSTAT = rIICSTAT;
+
+ for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
+ temp = IICCON;
+ if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
+ break;
+ udelay(2000);
+ }
+ if (k==S3C44B0_IIC_TIMEOUT)
+ return -1;
+
+ /* wait and check ACK */
+ temp = IICSTAT;
+ if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
+ return -1;
+
+ IICDS = addr;
+ IICCON = IICCON & ~(S3C44B0X_rIIC_INTPEND);
+
+ /* wait and check ACK */
+ for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
+ temp = IICCON;
+ if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
+ break;
+ udelay(2000);
+ }
+ if (k==S3C44B0_IIC_TIMEOUT)
+ return -1;
+
+ temp = IICSTAT;
+ if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
+ return -1;
+
+ /*
+ now we can start with the read operation...
+ */
+
+ IICDS = chip | 0x01; /* this is a read operation... */
+
+ rIICSTAT = 0x90; /*master recv*/
+ rIICSTAT |= (1<<5);
+ IICSTAT = rIICSTAT;
+
+ IICCON = IICCON & ~(S3C44B0X_rIIC_INTPEND);
+
+ /* wait and check ACK */
+ for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
+ temp = IICCON;
+ if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
+ break;
+ udelay(2000);
+ }
+ if (k==S3C44B0_IIC_TIMEOUT)
+ return -1;
+
+ temp = IICSTAT;
+ if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
+ return -1;
+
+ for (j=0; j<len-1; j++) {
+
+ /*clear pending bit to resume */
+
+ temp = IICCON & ~(S3C44B0X_rIIC_INTPEND);
+ IICCON = temp;
+
+ /* wait and check ACK */
+ for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
+ temp = IICCON;
+ if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
+ break;
+ udelay(2000);
+ }
+ if (k==S3C44B0_IIC_TIMEOUT)
+ return -1;
+
+
+ buffer[j] = IICDS; /*save readed data*/
+
+ } /*end for(j)*/
+
+ /*
+ reading the last data
+ unset ACK generation
+ */
+ temp = IICCON & ~(S3C44B0X_rIIC_INTPEND | (1<<7));
+ IICCON = temp;
+
+ /* wait but NOT check ACK */
+ for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
+ temp = IICCON;
+ if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
+ break;
+ udelay(2000);
+ }
+ if (k==S3C44B0_IIC_TIMEOUT)
+ return -1;
+
+ buffer[j] = IICDS; /*save readed data*/
+
+ rIICSTAT = 0x90; /*master recv*/
+
+ /* Write operation Terminate sending STOP */
+ IICSTAT = rIICSTAT;
+ /*Clear Int Pending Bit to RESUME*/
+ temp = IICCON;
+ IICCON = temp & (~S3C44B0X_rIIC_INTPEND);
+
+ IICCON = IICCON | (1<<7); /*restore ACK generation*/
+
+ return 0;
+}
+
+int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
+{
+ int j, k;
+ u32 rIICSTAT, temp;
+
+
+ /*
+ send the device offset
+ */
+
+ rIICSTAT = 0xD0;
+ IICSTAT = rIICSTAT;
+
+ IICDS = chip; /* this is a write operation... */
+
+ rIICSTAT |= (1<<5);
+ IICSTAT = rIICSTAT;
+
+ IICCON = IICCON & ~(S3C44B0X_rIIC_INTPEND);
+
+ /* wait and check ACK */
+ for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
+ temp = IICCON;
+ if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
+ break;
+ udelay(2000);
+ }
+ if (k==S3C44B0_IIC_TIMEOUT)
+ return -1;
+
+ temp = IICSTAT;
+ if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
+ return -1;
+
+ IICDS = addr;
+ IICCON = IICCON & ~(S3C44B0X_rIIC_INTPEND);
+
+ /* wait and check ACK */
+ for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
+ temp = IICCON;
+ if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
+ break;
+ udelay(2000);
+ }
+ if (k==S3C44B0_IIC_TIMEOUT)
+ return -1;
+
+ temp = IICSTAT;
+ if ((temp & S3C44B0X_rIIC_LAST_RECEIV_BIT) == S3C44B0X_rIIC_LAST_RECEIV_BIT )
+ return -1;
+
+ /*
+ now we can start with the read write operation
+ */
+ for (j=0; j<len; j++) {
+
+ IICDS = buffer[j]; /*prerare data to write*/
+
+ /*clear pending bit to resume*/
+
+ temp = IICCON & ~(S3C44B0X_rIIC_INTPEND);
+ IICCON = temp;
+
+ /* wait but NOT check ACK */
+ for(k=0; k<S3C44B0_IIC_TIMEOUT; k++) {
+ temp = IICCON;
+ if( (temp & S3C44B0X_rIIC_INTPEND) == S3C44B0X_rIIC_INTPEND)
+ break;
+
+ udelay(2000);
+ }
+
+ if (k==S3C44B0_IIC_TIMEOUT)
+ return -1;
+
+ } /* end for(j) */
+
+ /* sending stop to terminate */
+ rIICSTAT = 0xD0; /*master send*/
+ IICSTAT = rIICSTAT;
+ /*Clear Int Pending Bit to RESUME*/
+ temp = IICCON;
+ IICCON = temp & (~S3C44B0X_rIIC_INTPEND);
+
+ return 0;
+}
/***********************************************************************
*
- * (C) Copyright 2004
+ * (C) Copyright 2004-2009
* DENX Software Engineering
* Wolfgang Denk, wd@denx.de
* All rights reserved.
#include <asm/io.h>
#include <asm/atomic.h>
#include <ps2mult.h>
-#if defined(CONFIG_SYS_NS16550) || defined(CONFIG_MPC85xx)
-#include <ns16550.h>
+/* This is needed for ns16550.h */
+#ifndef CONFIG_SYS_NS16550_REG_SIZE
+#define CONFIG_SYS_NS16550_REG_SIZE 1
#endif
+#include <ns16550.h>
DECLARE_GLOBAL_DATA_PTR;
NS16550_t com_port = (NS16550_t)COM_BASE;
com_port->ier = 0x00;
- com_port->lcr = LCR_BKSE | LCR_8N1;
+ com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
com_port->dll = (CONFIG_SYS_NS16550_CLK / 16 / PS2SER_BAUD) & 0xff;
com_port->dlm = ((CONFIG_SYS_NS16550_CLK / 16 / PS2SER_BAUD) >> 8) & 0xff;
- com_port->lcr = LCR_8N1;
- com_port->mcr = (MCR_DTR | MCR_RTS);
- com_port->fcr = (FCR_FIFO_EN | FCR_RXSR | FCR_TXSR);
+ com_port->lcr = UART_LCR_8N1;
+ com_port->mcr = (UART_MCR_DTR | UART_MCR_RTS);
+ com_port->fcr = (UART_FCR_FIFO_EN | UART_FCR_RXSR | UART_FCR_TXSR);
return (0);
}
psc->psc_buffer_8 = chr;
#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
- while ((com_port->lsr & LSR_THRE) == 0);
+ while ((com_port->lsr & UART_LSR_THRE) == 0);
com_port->thr = chr;
#else
while (!(ps2ser_in(UART_LSR) & UART_LSR_THRE));
}
#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
- if (com_port->lsr & LSR_DR) {
+ if (com_port->lsr & UART_LSR_DR) {
res = com_port->rbr;
}
#else
} while (status & PSC_SR_RXRDY);
#elif defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
defined(CONFIG_MPC8548) || defined(CONFIG_MPC8555)
- } while (status & LSR_DR);
+ } while (status & UART_LSR_DR);
#else
} while (status & UART_IIR_RDI);
#endif
COBJS-$(CONFIG_NAND_ATMEL) += atmel_nand.o
COBJS-$(CONFIG_DRIVER_NAND_BFIN) += bfin_nand.o
+COBJS-$(CONFIG_NAND_DAVINCI) += davinci_nand.o
COBJS-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
COBJS-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
COBJS-$(CONFIG_NAND_NOMADIK) += nomadik.o
+COBJS-$(CONFIG_NAND_S3C2410) += s3c2410_nand.c
COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o
COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o
endif
#include <common.h>
#include <asm/io.h>
-
-#ifdef CONFIG_SYS_USE_NAND
-#if !defined(CONFIG_NAND_LEGACY)
-
#include <nand.h>
#include <asm/arch/nand_defs.h>
#include <asm/arch/emif_defs.h>
return(0);
}
-
-#else
-#error "U-Boot legacy NAND support not available for DaVinci chips"
-#endif
-#endif /* CONFIG_SYS_USE_NAND */
#define DEBUGN(x, args ...) {}
#endif
-#if defined(CONFIG_CMD_NAND)
-#if !defined(CONFIG_NAND_LEGACY)
-
#include <nand.h>
#include <s3c2410.h>
#include <asm/io.h>
return 0;
}
-
-#else
- #error "U-Boot legacy NAND support not available for S3C2410"
-#endif
-#endif
COBJS-$(CONFIG_RTC_RTC4543) += rtc4543.o
COBJS-$(CONFIG_RTC_RX8025) += rx8025.o
COBJS-$(CONFIG_RTC_S3C24X0) += s3c24x0_rtc.o
+COBJS-$(CONFIG_RTC_S3C44B0) += s3c44b0_rtc.o
COBJS-$(CONFIG_RTC_X1205) += x1205.o
COBJS := $(sort $(COBJS-y))
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * DAVE Srl
+ * http://www.dave-tech.it
+ * http://www.wawnet.biz
+ * mailto:info@wawnet.biz
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * S3C44B0 CPU specific code
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/hardware.h>
+#include <rtc.h>
+#include <bcd.h>
+
+int rtc_get (struct rtc_time* tm)
+{
+ RTCCON |= 1;
+ tm->tm_year = BCD2BIN(BCDYEAR);
+ tm->tm_mon = BCD2BIN(BCDMON);
+ tm->tm_wday = BCD2BIN(BCDDATE);
+ tm->tm_mday = BCD2BIN(BCDDAY);
+ tm->tm_hour = BCD2BIN(BCDHOUR);
+ tm->tm_min = BCD2BIN(BCDMIN);
+ tm->tm_sec = BCD2BIN(BCDSEC);
+
+ if (tm->tm_sec==0) {
+ /* we have to re-read the rtc data because of the "one second deviation" problem */
+ /* see RTC datasheet for more info about it */
+ tm->tm_year = BCD2BIN(BCDYEAR);
+ tm->tm_mon = BCD2BIN(BCDMON);
+ tm->tm_mday = BCD2BIN(BCDDAY);
+ tm->tm_wday = BCD2BIN(BCDDATE);
+ tm->tm_hour = BCD2BIN(BCDHOUR);
+ tm->tm_min = BCD2BIN(BCDMIN);
+ tm->tm_sec = BCD2BIN(BCDSEC);
+ }
+
+ RTCCON &= ~1;
+
+ if(tm->tm_year >= 70)
+ tm->tm_year += 1900;
+ else
+ tm->tm_year += 2000;
+
+ return 0;
+}
+
+int rtc_set (struct rtc_time* tm)
+{
+ if(tm->tm_year < 2000)
+ tm->tm_year -= 1900;
+ else
+ tm->tm_year -= 2000;
+
+ RTCCON |= 1;
+ BCDYEAR = BIN2BCD(tm->tm_year);
+ BCDMON = BIN2BCD(tm->tm_mon);
+ BCDDAY = BIN2BCD(tm->tm_mday);
+ BCDDATE = BIN2BCD(tm->tm_wday);
+ BCDHOUR = BIN2BCD(tm->tm_hour);
+ BCDMIN = BIN2BCD(tm->tm_min);
+ BCDSEC = BIN2BCD(tm->tm_sec);
+ RTCCON &= 1;
+
+ return 0;
+}
+
+void rtc_reset (void)
+{
+ RTCCON |= 1;
+ BCDYEAR = 0;
+ BCDMON = 0;
+ BCDDAY = 0;
+ BCDDATE = 0;
+ BCDHOUR = 0;
+ BCDMIN = 0;
+ BCDSEC = 0;
+ RTCCON &= 1;
+}
+
COBJS-$(CONFIG_DRIVER_S3C4510_UART) += s3c4510b_uart.o
COBJS-$(CONFIG_S3C64XX) += s3c64xx.o
COBJS-$(CONFIG_SYS_NS16550_SERIAL) += serial.o
+COBJS-$(CONFIG_CLPS7111_SERIAL) += serial_clps7111.o
+COBJS-$(CONFIG_IMX_SERIAL) += serial_imx.o
COBJS-$(CONFIG_IXP_SERIAL) += serial_ixp.o
+COBJS-$(CONFIG_KS8695_SERIAL) += serial_ks8695.o
+COBJS-$(CONFIG_LPC2292_SERIAL) += serial_lpc2292.o
COBJS-$(CONFIG_MAX3100_SERIAL) += serial_max3100.o
+COBJS-$(CONFIG_MX31_UART) += serial_mx31.o
+COBJS-$(CONFIG_NETARM_SERIAL) += serial_netarm.o
COBJS-$(CONFIG_PL010_SERIAL) += serial_pl01x.o
COBJS-$(CONFIG_PL011_SERIAL) += serial_pl01x.o
+COBJS-$(CONFIG_SA1100_SERIAL) += serial_sa1100.o
+COBJS-$(CONFIG_S3C24X0_SERIAL) += serial_s3c24x0.o
+COBJS-$(CONFIG_S3C44B0_SERIAL) += serial_s3c44b0.o
COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
COBJS-$(CONFIG_USB_TTY) += usbtty.o
#include <config.h>
#include <ns16550.h>
-#define LCRVAL LCR_8N1 /* 8 data, 1 stop, no parity */
-#define MCRVAL (MCR_DTR | MCR_RTS) /* RTS/DTR */
-#define FCRVAL (FCR_FIFO_EN | FCR_RXSR | FCR_TXSR) /* Clear & enable FIFOs */
+#define UART_LCRVAL UART_LCR_8N1 /* 8 data, 1 stop, no parity */
+#define UART_MCRVAL (UART_MCR_DTR | \
+ UART_MCR_RTS) /* RTS/DTR */
+#define UART_FCRVAL (UART_FCR_FIFO_EN | \
+ UART_FCR_RXSR | \
+ UART_FCR_TXSR) /* Clear & enable FIFOs */
void NS16550_init (NS16550_t com_port, int baud_divisor)
{
#ifdef CONFIG_OMAP
com_port->mdr1 = 0x7; /* mode select reset TL16C750*/
#endif
- com_port->lcr = LCR_BKSE | LCRVAL;
+ com_port->lcr = UART_LCR_BKSE | UART_LCRVAL;
com_port->dll = 0;
com_port->dlm = 0;
- com_port->lcr = LCRVAL;
- com_port->mcr = MCRVAL;
- com_port->fcr = FCRVAL;
- com_port->lcr = LCR_BKSE | LCRVAL;
+ com_port->lcr = UART_LCRVAL;
+ com_port->mcr = UART_MCRVAL;
+ com_port->fcr = UART_FCRVAL;
+ com_port->lcr = UART_LCR_BKSE | UART_LCRVAL;
com_port->dll = baud_divisor & 0xff;
com_port->dlm = (baud_divisor >> 8) & 0xff;
- com_port->lcr = LCRVAL;
+ com_port->lcr = UART_LCRVAL;
#if defined(CONFIG_OMAP)
#if defined(CONFIG_APTIX)
com_port->mdr1 = 3; /* /13 mode so Aptix 6MHz can hit 115200 */
void NS16550_reinit (NS16550_t com_port, int baud_divisor)
{
com_port->ier = 0x00;
- com_port->lcr = LCR_BKSE | LCRVAL;
+ com_port->lcr = UART_LCR_BKSE | UART_LCRVAL;
com_port->dll = 0;
com_port->dlm = 0;
- com_port->lcr = LCRVAL;
- com_port->mcr = MCRVAL;
- com_port->fcr = FCRVAL;
- com_port->lcr = LCR_BKSE;
+ com_port->lcr = UART_LCRVAL;
+ com_port->mcr = UART_MCRVAL;
+ com_port->fcr = UART_FCRVAL;
+ com_port->lcr = UART_LCR_BKSE;
com_port->dll = baud_divisor & 0xff;
com_port->dlm = (baud_divisor >> 8) & 0xff;
- com_port->lcr = LCRVAL;
+ com_port->lcr = UART_LCRVAL;
}
#endif /* CONFIG_NS16550_MIN_FUNCTIONS */
void NS16550_putc (NS16550_t com_port, char c)
{
- while ((com_port->lsr & LSR_THRE) == 0);
+ while ((com_port->lsr & UART_LSR_THRE) == 0);
com_port->thr = c;
}
#ifndef CONFIG_NS16550_MIN_FUNCTIONS
char NS16550_getc (NS16550_t com_port)
{
- while ((com_port->lsr & LSR_DR) == 0) {
+ while ((com_port->lsr & UART_LSR_DR) == 0) {
#ifdef CONFIG_USB_TTY
extern void usbtty_poll(void);
usbtty_poll();
int NS16550_tstc (NS16550_t com_port)
{
- return ((com_port->lsr & LSR_DR) != 0);
+ return ((com_port->lsr & UART_LSR_DR) != 0);
}
#endif /* CONFIG_NS16550_MIN_FUNCTIONS */
*/
#include <common.h>
-
-#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312) || defined(CONFIG_ARMADILLO)
-
#include <clps7111.h>
DECLARE_GLOBAL_DATA_PTR;
serial_putc (*s++);
}
}
-
-#elif defined(CONFIG_LPC2292)
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#include <asm/arch/hardware.h>
-
-void serial_setbrg (void)
-{
- unsigned short divisor = 0;
-
- switch (gd->baudrate) {
- case 1200: divisor = 3072; break;
- case 9600: divisor = 384; break;
- case 19200: divisor = 192; break;
- case 38400: divisor = 96; break;
- case 57600: divisor = 64; break;
- case 115200: divisor = 32; break;
- default: hang (); break;
- }
-
- /* init serial UART0 */
- PUT8(U0LCR, 0);
- PUT8(U0IER, 0);
- PUT8(U0LCR, 0x80); /* DLAB=1 */
- PUT8(U0DLL, (unsigned char)(divisor & 0x00FF));
- PUT8(U0DLM, (unsigned char)(divisor >> 8));
- PUT8(U0LCR, 0x03); /* 8N1, DLAB=0 */
- PUT8(U0FCR, 1); /* Enable RX and TX FIFOs */
-}
-
-int serial_init (void)
-{
- unsigned long pinsel0;
-
- serial_setbrg ();
-
- pinsel0 = GET32(PINSEL0);
- pinsel0 &= ~(0x00000003);
- pinsel0 |= 5;
- PUT32(PINSEL0, pinsel0);
-
- return (0);
-}
-
-void serial_putc (const char c)
-{
- if (c == '\n')
- {
- while((GET8(U0LSR) & (1<<5)) == 0); /* Wait for empty U0THR */
- PUT8(U0THR, '\r');
- }
-
- while((GET8(U0LSR) & (1<<5)) == 0); /* Wait for empty U0THR */
- PUT8(U0THR, c);
-}
-
-int serial_getc (void)
-{
- while((GET8(U0LSR) & 1) == 0);
- return GET8(U0RBR);
-}
-
-void
-serial_puts (const char *s)
-{
- while (*s) {
- serial_putc (*s++);
- }
-}
-
-/* Test if there is a byte to read */
-int serial_tstc (void)
-{
- return (GET8(U0LSR) & 1);
-}
-
-#endif
*/
#include <common.h>
-#if defined (CONFIG_IMX)
-
#include <asm/arch/imx-regs.h>
-#ifndef CONFIG_IMX_SERIAL_NONE
-
#if defined CONFIG_IMX_SERIAL1
#define UART_BASE IMX_UART1_BASE
#elif defined CONFIG_IMX_SERIAL2
serial_putc (*s++);
}
}
-#endif /* CONFIG_IMX_SERIAL_NONE */
-#endif /* defined CONFIG_IMX */
--- /dev/null
+/*
+ * (C) Copyright 2002-2004
+ * Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void serial_setbrg (void)
+{
+ unsigned short divisor = 0;
+
+ switch (gd->baudrate) {
+ case 1200: divisor = 3072; break;
+ case 9600: divisor = 384; break;
+ case 19200: divisor = 192; break;
+ case 38400: divisor = 96; break;
+ case 57600: divisor = 64; break;
+ case 115200: divisor = 32; break;
+ default: hang (); break;
+ }
+
+ /* init serial UART0 */
+ PUT8(U0LCR, 0);
+ PUT8(U0IER, 0);
+ PUT8(U0LCR, 0x80); /* DLAB=1 */
+ PUT8(U0DLL, (unsigned char)(divisor & 0x00FF));
+ PUT8(U0DLM, (unsigned char)(divisor >> 8));
+ PUT8(U0LCR, 0x03); /* 8N1, DLAB=0 */
+ PUT8(U0FCR, 1); /* Enable RX and TX FIFOs */
+}
+
+int serial_init (void)
+{
+ unsigned long pinsel0;
+
+ serial_setbrg ();
+
+ pinsel0 = GET32(PINSEL0);
+ pinsel0 &= ~(0x00000003);
+ pinsel0 |= 5;
+ PUT32(PINSEL0, pinsel0);
+
+ return (0);
+}
+
+void serial_putc (const char c)
+{
+ if (c == '\n')
+ {
+ while((GET8(U0LSR) & (1<<5)) == 0); /* Wait for empty U0THR */
+ PUT8(U0THR, '\r');
+ }
+
+ while((GET8(U0LSR) & (1<<5)) == 0); /* Wait for empty U0THR */
+ PUT8(U0THR, c);
+}
+
+int serial_getc (void)
+{
+ while((GET8(U0LSR) & 1) == 0);
+ return GET8(U0RBR);
+}
+
+void
+serial_puts (const char *s)
+{
+ while (*s) {
+ serial_putc (*s++);
+ }
+}
+
+/* Test if there is a byte to read */
+int serial_tstc (void)
+{
+ return (GET8(U0LSR) & 1);
+}
+
*/
#include <common.h>
-
-#if defined CONFIG_MX31_UART
-
#include <asm/arch/mx31.h>
#define __REG(x) (*((volatile u32 *)(x)))
return 0;
}
-
-
-#endif /* CONFIG_MX31 */
*/
#include <common.h>
-
-#ifdef CONFIG_NETARM
-
#include <asm/hardware.h>
DECLARE_GLOBAL_DATA_PTR;
serial_putc (*s++);
}
}
-
-#endif /* CONFIG_NETARM */
*/
#include <common.h>
-#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB)
-
#if defined(CONFIG_S3C2400) || defined(CONFIG_TRAB)
#include <s3c2400.h>
#elif defined(CONFIG_S3C2410)
INIT_S3C_SERIAL_STRUCTURE(2, "s3ser2", "S3UART3");
#endif /* CONFIG_SERIAL_MULTI */
-
-#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */
# host
COBJS-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
COBJS-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o
+COBJS-$(CONFIG_USB_S3C64XX) += s3c64xx_usb.o
COBJS-$(CONFIG_USB_SL811HS) += sl811_usb.o
COBJS-$(CONFIG_USB_EHCI_FSL) += usb_ehci_fsl.o
COBJS-$(CONFIG_USB_EHCI_PCI) += usb_ehci_pci.o
* MA 02111-1307 USA
*/
-#if defined(CONFIG_S3C4510B)
-#include <asm-arm/arch-arm720t/s3c4510b.h>
-#elif defined(CONFIG_NETARM)
+#if defined(CONFIG_NETARM)
#include <asm-arm/arch-arm720t/netarm_registers.h>
#elif defined(CONFIG_IMPA7)
/* include IMPA7 specific hardware file if there was one */
/* common/flash.c */
void flash_perror (int);
-/* common/cmd_autoscript.c */
-int autoscript (ulong addr, const char *fit_uname);
+/* common/cmd_source.c */
+int source (ulong addr, const char *fit_uname);
extern ulong load_addr; /* Default Load Address */
#define CONFIG_CMD_AMBAPP /* AMBA Plug & Play Bus print utility */
#define CONFIG_CMD_ASKENV /* ask for env variable */
-#define CONFIG_CMD_AUTOSCRIPT /* Autoscript Support */
#define CONFIG_CMD_BDI /* bdinfo */
#define CONFIG_CMD_BEDBUG /* Include BedBug Debugger */
#define CONFIG_CMD_BMP /* BMP support */
#define CONFIG_CMD_SETEXPR /* setexpr support */
#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
#define CONFIG_CMD_SNTP /* SNTP support */
+#define CONFIG_CMD_SOURCE /* "source" command support */
#define CONFIG_CMD_SPI /* SPI utility */
#define CONFIG_CMD_TERMINAL /* built-in Serial Terminal */
#define CONFIG_CMD_UNIVERSE /* Tundra Universe Support */
* hardware, not fully tested, etc.).
*/
-#define CONFIG_CMD_AUTOSCRIPT /* Autoscript Support */
#define CONFIG_CMD_BDI /* bdinfo */
#define CONFIG_CMD_BOOTD /* bootd */
#define CONFIG_CMD_CONSOLE /* coninfo */
#define CONFIG_CMD_NFS /* NFS support */
#define CONFIG_CMD_RUN /* run command in env variable */
#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
+#define CONFIG_CMD_SOURCE /* "source" command support */
#define CONFIG_CMD_XIMG /* Load part of Multi Image */
#endif /* _CONFIG_CMD_DEFAULT_H */
#define CONFIG_ADNPESC1 1 /* SSV ADNP/ESC1 board */
#define CONFIG_SYS_CLK_FREQ CONFIG_SYS_NIOS_CPU_CLK/* 50 MHz core clock */
#define CONFIG_SYS_HZ 1000 /* 1 msec time tick */
-#undef CONFIG_SYS_CLKS_IN_HZ
#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
/*------------------------------------------------------------------------
*/
#include <config_cmd_default.h>
+#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
-#define CONFIG_CMD_DATE
+#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
+#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
-#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_SOURCE
#define CONFIG_CMD_USB
-#define CONFIG_CMD_AUTOSCRIPT
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
/*
* select serial console configuration
*/
+#define CONFIG_S3C44B0_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
+#define CONFIG_S3C44B0_I2C
+#define CONFIG_RTC_S3C44B0
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SYS_MEMTEST_START 0x0C400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x0c700000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* 1 kHz */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_SYS_HUSH_PARSER 1
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#define CONFIG_AUTOSCRIPT 1
+#define CONFIG_SOURCE 1
/*
* Command line configuration.
*/
+#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_BDI
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMI
#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DATE
#define CONFIG_CMD_RUN
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_SETGETDCR
+#define CONFIG_CMD_SOURCE
/*
#define CONFIG_DK1C20 1 /* Cyclone DK-1C20 board*/
#define CONFIG_SYS_CLK_FREQ CONFIG_SYS_NIOS_CPU_CLK/* 50 MHz core clock */
#define CONFIG_SYS_HZ 1000 /* 1 msec time tick */
-#undef CONFIG_SYS_CLKS_IN_HZ
#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
/*------------------------------------------------------------------------
#define CONFIG_DK1S10 1 /* Stratix DK-1S10 board*/
#define CONFIG_SYS_CLK_FREQ CONFIG_SYS_NIOS_CPU_CLK/* 50 MHz core clock */
#define CONFIG_SYS_HZ 1000 /* 1 msec time tick */
-#undef CONFIG_SYS_CLKS_IN_HZ
#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
/*------------------------------------------------------------------------
#include <config_cmd_default.h>
-#define CONFIG_CMD_AUTOSCRIPT
-#define CONFIG_CMD_BSP
+#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_BMP
+#define CONFIG_CMD_BSP
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DTT
#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
-#define CONFIG_CMD_USB
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SOURCE
+#define CONFIG_CMD_USB
#define CONFIG_SUPPORT_VFAT
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-#define CONFIG_AUTOSCRIPT 1
+#define CONFIG_SOURCE 1
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_CMD_PING
#define CONFIG_CMD_SAVES
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_BOOTD
#undef CONFIG_CMD_CONSOLE
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_ITEST
#undef CONFIG_CMD_NFS
#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_SOURCE
#undef CONFIG_CMD_XIMG
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
-#define CONFIG_SYS_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
/*
* Set default IP stuff just to get bootstrap entries into the
- * environment so that we can autoscript the full default environment.
+ * environment so that we can source the full default environment.
*/
#define CONFIG_ETHADDR 9a:52:63:15:85:25
#define CONFIG_SERVERIP 10.0.4.201
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10)
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L (0)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \
+ BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L (0)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \
+ BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L 0
#define MV_INITRD_LENGTH 0x00300000
#define MV_SCRATCH_ADDR 0x00000000
#define MV_SCRATCH_LENGTH MV_INITRD_LENGTH
-#define MV_AUTOSCR_ADDR 0xff840000
-#define MV_AUTOSCR_ADDR2 0xff850000
+#define MV_SOURCE_ADDR 0xff840000
+#define MV_SOURCE_ADDR2 0xff850000
#define MV_DTB_ADDR 0xfffc0000
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define CONFIG_RESET_TO_RETRY 1000
#define CONFIG_BOOTCOMMAND "if imi ${autoscr_addr}; \
- then autoscr ${autoscr_addr}; \
- else autoscr ${autoscr_addr2}; \
+ then source ${autoscr_addr}; \
+ else source ${autoscr_addr2}; \
fi;"
#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs"
"fpga=0\0" \
"fpgadata=" MK_STR(MV_FPGA_DATA) "\0" \
"fpgadatasize=" MK_STR(MV_FPGA_SIZE) "\0" \
- "autoscr_addr=" MK_STR(MV_AUTOSCR_ADDR) "\0" \
- "autoscr_addr2=" MK_STR(MV_AUTOSCR_ADDR2) "\0" \
+ "autoscr_addr=" MK_STR(MV_SOURCE_ADDR) "\0" \
+ "autoscr_addr2=" MK_STR(MV_SOURCE_ADDR2) "\0" \
"mv_kernel_addr=" MK_STR(MV_KERNEL_ADDR) "\0" \
"mv_kernel_addr_ram=" MK_STR(MV_KERNEL_ADDR_RAM) "\0" \
"mv_initrd_addr=" MK_STR(MV_INITRD_ADDR) "\0" \
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFF800000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \
+ BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L 0
#define CONFIG_SYS_IBAT7U 0
#define MV_FPGA_SIZE 0x00076ca2
#define MV_KERNEL_ADDR 0xff810000
#define MV_INITRD_ADDR 0xffb00000
-#define MV_AUTOSCR_ADDR 0xff804000
-#define MV_AUTOSCR_ADDR2 0xff806000
+#define MV_SOURCE_ADDR 0xff804000
+#define MV_SOURCE_ADDR2 0xff806000
#define MV_DTB_ADDR 0xff808000
#define MV_INITRD_LENGTH 0x00400000
#define MV_INITRD_ADDR_RAM 0x01000000
#define CONFIG_BOOTCOMMAND "if imi ${autoscr_addr}; \
- then autoscr ${autoscr_addr}; \
- else autoscr ${autoscr_addr2}; \
+ then source ${autoscr_addr}; \
+ else source ${autoscr_addr2}; \
fi;"
#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs"
"fpga=0\0" \
"fpgadata=" MK_STR(MV_FPGA_DATA) "\0" \
"fpgadatasize=" MK_STR(MV_FPGA_SIZE) "\0" \
- "autoscr_addr=" MK_STR(MV_AUTOSCR_ADDR) "\0" \
- "autoscr_addr2=" MK_STR(MV_AUTOSCR_ADDR2) "\0" \
+ "autoscr_addr=" MK_STR(MV_SOURCE_ADDR) "\0" \
+ "autoscr_addr2=" MK_STR(MV_SOURCE_ADDR2) "\0" \
"mv_kernel_addr=" MK_STR(MV_KERNEL_ADDR) "\0" \
"mv_kernel_addr_ram=" MK_STR(MV_KERNEL_ADDR_RAM) "\0" \
"mv_initrd_addr=" MK_STR(MV_INITRD_ADDR) "\0" \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
"bootm"
-#define CONFIG_AUTOSCRIPT
+#define CONFIG_SOURCE
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
"bootm"
-#define CONFIG_AUTOSCRIPT
+#define CONFIG_SOURCE
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled, for now */
-#define CONFIG_AUTOSCRIPT
+#define CONFIG_SOURCE
/*
* BOOTP options
*/
#include <config_cmd_default.h>
-#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_SOURCE
/* call various generic functions */
#define CONFIG_CMD_PCI
#define CONFIG_CMD_BSP
-#undef CONFIG_CMD_AUTOSCRIPT
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_SAVEENV
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SAVEENV
+#undef CONFIG_CMD_SOURCE
#define CONFIG_BAUDRATE 19200 /* console baudrate */
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10)
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L (0)
/*
* select serial console configuration
*/
+#define CONFIG_LPC2292_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0x81800000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x83000000 /* 24 MB in SRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* default load address */
/* for uClinux img is here*/
#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
* This time is further subdivided by a local divisor.
*/
-#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE /* use timer 1 */
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
#define CONFIG_CMD_BEDBUG
-#define CONFIG_AUTOSCRIPT 1
+#define CONFIG_SOURCE 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
#undef CONFIG_LOADS_ECHO /* NO echo on for serial download */
/*
* Set default IP stuff just to get bootstrap entries into the
- * environment so that we can autoscript the full default environment.
+ * environment so that we can source the full default environment.
*/
#define CONFIG_ETHADDR 9a:52:63:15:85:25
#define CONFIG_SERVERIP 10.0.4.200
#define CONFIG_IPADDR 10.0.4.111
-/*-----------------------------------------------------------------------
- * Defaults for Autoscript
- */
#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
#define CONFIG_SYS_TFTP_LOADADDR 0x00100000
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
#endif /* __CONFIG_H */
#define CUSTOM_ENV_SETTINGS \
"bootfile=cam5200/uImage\0" \
"u-boot=cam5200/u-boot.bin\0" \
- "setup=tftp 200000 cam5200/setup.img; autoscr 200000\0"
+ "setup=tftp 200000 cam5200/setup.img; source 200000\0"
#endif
#if defined(CONFIG_TQM5200_B)
/*
* select serial console configuration
*/
+#define CONFIG_S3C24X0_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on VCMA9 */
/************************************************************
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_SYS_LOAD_ADDR 0x30800000 /* default load address */
-
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
/* we configure PWM Timer 4 to 1us ~ 1MHz */
/*#define CONFIG_SYS_HZ 1000000 */
#define CONFIG_SYS_HZ 1562500
* Command line configuration.
*/
-#define CONFIG_CMD_AUTOSCRIPT
#define CONFIG_CMD_BDI
#define CONFIG_CMD_CONSOLE
#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_FLASH
#define CONFIG_CMD_IMI
#define CONFIG_CMD_IMLS
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SOURCE
/*
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE {9600}
-#define CONFIG_SYS_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE {9600}
-#define CONFIG_SYS_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* everything, incl board info, in Hz */
-#undef CONFIG_SYS_CLKS_IN_HZ
/* spec says 66.666 MHz, but it appears to be 33 */
#define CONFIG_SYS_HZ 3333333
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* everything, incl board info, in Hz */
-#undef CONFIG_SYS_CLKS_IN_HZ
/* spec says 66.666 MHz, but it appears to be 33 */
#define CONFIG_SYS_HZ 3333333
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* everything, incl board info, in Hz */
-#undef CONFIG_SYS_CLKS_IN_HZ
/* spec says 66.666 MHz, but it appears to be 33 */
#define CONFIG_SYS_HZ 3333333
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* everything, incl board info, in Hz */
-#undef CONFIG_SYS_CLKS_IN_HZ
/* spec says 66.666 MHz, but it appears to be 33 */
#define CONFIG_SYS_HZ 3333333
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
#define CONFIG_CMD_PING 1
#define CONFIG_CMD_DHCP 1
#define CONFIG_MTD_PARTITIONS
#endif
-#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_SOURCE
#ifndef CONFIG_SYS_USE_NOR
# undef CONFIG_CMD_FLASH
#define CONFIG_SYS_MEMTEST_START (OMAP2420_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP2420_SDRC_CS0+SZ_31M)
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
/* default load address */
#define CONFIG_SYS_LOAD_ADDR (OMAP2420_SDRC_CS0)
* or by 32KHz clk, or from external sig. This rate is divided by a local
* divisor.
*/
-#define V_PVT 7 /* use with 12MHz/128 */
-
#define CONFIG_SYS_TIMERBASE OMAP2420_GPT2
-#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
/*
* select serial console configuration
*/
+#define CONFIG_CLPS7111_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x00040000 /* default load address for armadillo: kernel img is here*/
#define CONFIG_SYS_HZ 2000 /* decrementer freq: 2 kHz */
/*
* select serial console configuration
*/
+#define CONFIG_SA1100_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on Intel Assabet */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ
-
#define CONFIG_SYS_LOAD_ADDR 0xc0000000 /* default load address */
#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
#define CONFIG_CMD_PING 1
#define CONFIG_CMD_DHCP 1
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
#define CONFIG_CMD_PING 1
#define CONFIG_CMD_DHCP 1
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
#define CONFIG_CMD_PING 1
#define CONFIG_CMD_DHCP 1
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
#define CONFIG_CMD_PING 1
#define CONFIG_CMD_DHCP 1
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_SOURCE
#undef CONFIG_CMD_USB
#define CONFIG_CMD_NAND 1
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_SOURCE
#undef CONFIG_CMD_XIMG
#define CONFIG_ATMEL_USART 1
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MMC
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_SOURCE
#undef CONFIG_CMD_XIMG
#define CONFIG_ATMEL_USART 1
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MMC
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_SOURCE
#undef CONFIG_CMD_XIMG
#define CONFIG_ATMEL_USART 1
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ
-
#define CONFIG_SYS_LOAD_ADDR 0xa2000000 /* default load address */
#define CONFIG_SYS_HZ 1000
* select serial console configuration
*/
#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_KS8695_SERIAL
#define CONFIG_SERIAL1
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_MEMTEST_START 0x00800000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 16 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x00008000 /* default load address */
#define CONFIG_SYS_HZ (1000) /* 1ms resolution ticks */
* select serial console configuration
*/
#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_KS8695_SERIAL
#define CONFIG_SERIAL1
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_MEMTEST_START 0x00800000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 16 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x00008000 /* default load address */
#define CONFIG_SYS_HZ (1000) /* 1ms resolution ticks */
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa2000000 /* default load address */
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa3000000 /* default load address */
/* RS: where is this documented? */
/* RS: is this where U-Boot is */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_SYS_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_SYS_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
/* Flash & Environment */
/*=====================*/
#ifdef CONFIG_SYS_USE_NAND
+#define CONFIG_NAND_DAVINCI
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
/*=====================*/
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_SYS_NO_FLASH
+#define CONFIG_NAND_DAVINCI
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
#define CONFIG_ENV_SIZE SZ_128K
/* Flash & Environment */
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_SYS_NO_FLASH
+#define CONFIG_NAND_DAVINCI
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
#define CONFIG_ENV_SIZE SZ_128K
/* Flash & Environment */
/*=====================*/
#ifdef CONFIG_SYS_USE_NAND
+#define CONFIG_NAND_DAVINCI
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_SYS_MEMTEST_START 0x80400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x80800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
#define CONFIG_SYS_HZ 1000
/*
* select serial console configuration
*/
+#define CONFIG_SA1100_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xc0200000 /* default load address */
#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
*/
#include <config_cmd_default.h>
-#define CONFIG_CMD_AUTOSCRIPT /* Autoscript Support */
#define CONFIG_CMD_BDI /* bdinfo */
#define CONFIG_CMD_BOOTD /* bootd */
#define CONFIG_CMD_CONSOLE /* coninfo */
#define CONFIG_CMD_ECHO /* echo arguments */
-#define CONFIG_CMD_SAVEENV /* saveenv */
#define CONFIG_CMD_FLASH /* flinfo, erase, protect */
#define CONFIG_CMD_FPGA /* FPGA configuration Support */
#define CONFIG_CMD_IMI /* iminfo */
#define CONFIG_CMD_IMLS /* List all found images */
+#define CONFIG_CMD_IRQ /* IRQ Information */
#define CONFIG_CMD_ITEST /* Integer (and string) test */
#define CONFIG_CMD_LOADB /* loadb */
#define CONFIG_CMD_LOADS /* loads */
#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
#undef CONFIG_CMD_NFS /* NFS support */
#define CONFIG_CMD_RUN /* run command in env variable */
+#define CONFIG_CMD_SAVEENV /* saveenv */
#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
+#define CONFIG_CMD_SOURCE /* "source" command Support */
#define CONFIG_CMD_XIMG /* Load part of Multi Image */
-#define CONFIG_CMD_IRQ /* IRQ Information */
#define CONFIG_BOOTDELAY 15
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_HZ 1024 /* incrementer freq: 1kHz */
/*
* select serial console configuration
*/
+#define CONFIG_CLPS7111_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xc0500000 /* default load address */
#define CONFIG_SYS_HZ 2000 /* decrementer freq: 2 kHz */
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00780000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x00000000 /* default load address */
#define CONFIG_SYS_SYS_CLK_FREQ 50000000 /* CPU freq: 50 MHz */
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MMC
-#undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_SOURCE
#undef CONFIG_CMD_XIMG
#define CONFIG_ATMEL_USART 1
/*
* select serial console configuration
*/
+#define CONFIG_SA1100_SERIAL
#define CONFIG_SERIAL3 1 /* we use SERIAL 3 on ADS GCPlus */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xc0000000 /* default load address */
#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
/*
* Supported commands
*/
-#define CONFIG_CMD_AMBAPP /* AMBA Plyg&Play information */
-#define CONFIG_CMD_AUTOSCRIPT /* Autoscript Support */
-#define CONFIG_CMD_BDI /* bdinfo */
-#define CONFIG_CMD_CONSOLE /* coninfo */
+#define CONFIG_CMD_AMBAPP /* AMBA Plyg&Play information */
+#define CONFIG_CMD_BDI /* bdinfo */
+#define CONFIG_CMD_CONSOLE /* coninfo */
#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ECHO /* echo arguments */
-#define CONFIG_CMD_FPGA /* FPGA configuration Support */
+#define CONFIG_CMD_ECHO /* echo arguments */
+#define CONFIG_CMD_FPGA /* FPGA configuration Support */
#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_ITEST /* Integer (and string) test */
-#define CONFIG_CMD_LOADB /* loadb */
-#define CONFIG_CMD_LOADS /* loads */
+#define CONFIG_CMD_ITEST /* Integer (and string) test */
+#define CONFIG_CMD_LOADB /* loadb */
+#define CONFIG_CMD_LOADS /* loads */
#define CONFIG_CMD_MISC /* Misc functions like sleep etc */
-#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_RUN /* run command in env variable */
-#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
-#define CONFIG_CMD_XIMG /* Load part of Multi Image */
+#define CONFIG_CMD_RUN /* run command in env variable */
+#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
+#define CONFIG_CMD_SOURCE /* "source" command support */
+#define CONFIG_CMD_XIMG /* Load part of Multi Image */
/*
* Autobooting
/*
* Supported commands
*/
-#define CONFIG_CMD_AUTOSCRIPT /* Autoscript Support */
-#define CONFIG_CMD_BDI /* bdinfo */
-#define CONFIG_CMD_CONSOLE /* coninfo */
+#define CONFIG_CMD_BDI /* bdinfo */
+#define CONFIG_CMD_CONSOLE /* coninfo */
#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ECHO /* echo arguments */
-#define CONFIG_CMD_FPGA /* FPGA configuration Support */
+#define CONFIG_CMD_ECHO /* echo arguments */
+#define CONFIG_CMD_FPGA /* FPGA configuration Support */
#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_ITEST /* Integer (and string) test */
-#define CONFIG_CMD_LOADB /* loadb */
-#define CONFIG_CMD_LOADS /* loads */
+#define CONFIG_CMD_ITEST /* Integer (and string) test */
+#define CONFIG_CMD_LOADB /* loadb */
+#define CONFIG_CMD_LOADS /* loads */
#define CONFIG_CMD_MISC /* Misc functions like sleep etc */
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_RUN /* run command in env variable */
-#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
-#define CONFIG_CMD_XIMG /* Load part of Multi Image */
+#define CONFIG_CMD_RUN /* run command in env variable */
+#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
+#define CONFIG_CMD_SOURCE /* "source" command support */
+#define CONFIG_CMD_XIMG /* Load part of Multi Image */
/*
* Autobooting
#define CONFIG_CMD_IDE
#define CONFIG_CMD_DHCP
-#undef CONFIG_CMD_SAVEENV
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_BEDBUG
+#undef CONFIG_CMD_ELF
#undef CONFIG_CMD_FAT
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_MII
-#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_ELF
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_BEDBUG
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_MII
#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_SAVEENV
+#undef CONFIG_CMD_SOURCE
/*
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x03c00000 /* 4 ... 60 MB in DRAM */
-#define CONFIG_SYS_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
* select serial console configuration
*/
+#define CONFIG_CLPS7111_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xc1000000 /* default load address */
#define CONFIG_SYS_HZ 2000 /* decrementer freq: 2 kHz */
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa3000000 /* load kernel to this address */
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */
/*-----------------------------------------------------------------------
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size*/
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */
/*-----------------------------------------------------------------------
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
#define CONFIG_SYS_HZ 3333333 /* spec says 66.666 MHz, but it appears to be 33 */
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/* valid baudrates */
"new_esw_0x${IVM_BoardId}_0x${IVM_HWKey}.scr \0" \
"new_esw=run set_new_esw_script; " \
"tftp ${autoscr_ws} ${new_esw_script}; " \
- "iminfo ${autoscr_ws}; autoscr ${autoscr_ws} \0" \
+ "iminfo ${autoscr_ws}; source ${autoscr_ws} \0" \
"bootlimit=0 \0" \
CONFIG_KM_DEF_ENV_IOMUX \
CONFIG_KM_DEF_ENV_PRIVATE \
/*
* select serial console configuration
*/
+#define CONFIG_SA1100_SERIAL
#define CONFIG_SERIAL3 1 /* we use SERIAL 3 on LART */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xc8000000 /* default load address */
#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
#define CONFIG_SYS_MEMTEST_START 0x08000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0800ffff /* 64 KiB */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x08000000 /* load kernel to this address */
#define CONFIG_SYS_HZ 1000
/*
* select serial console configuration
*/
+#define CONFIG_LPC2292_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0x40000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x40000000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x00040000 /* default load address for */
/* armadillo: kernel img is here*/
#define CONFIG_SYS_MEMTEST_START 0xc0300000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0500000 /* 2 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xc0f00000 /* default load address */
/* valid baudrates */
#define CONFIG_SYS_MEMTEST_START 0xc0300000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0500000 /* 2 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xc0f00000 /* default load address */
/* valid baudrates */
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
#define CONFIG_SYS_HZ 1000
* 3 = 0x3C+0x3F = F3 + F6 : enable test mode
*/
-#define CONFIG_BOOTCOMMAND "autoscr 40040000;saveenv"
+#define CONFIG_BOOTCOMMAND "source 40040000;saveenv"
/* "gatewayip=10.8.211.250\0" \ */
#define CONFIG_EXTRA_ENV_SETTINGS \
"key_magic2=3A+3C\0" \
"key_cmd2=echo *** Entering Update Mode ***;" \
"if fatload ide 0:3 10000 update.scr;" \
- "then autoscr 10000;" \
+ "then source 10000;" \
"else echo *** UPDATE FAILED ***;" \
"fi\0" \
"key_magic3=3C+3F\0" \
"cp.b 200000 FFF80000 80000\0" \
"upd=run load update\0" \
"lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \
- "autoscr 200000\0" \
+ "source 200000\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
/*
* select serial console configuration
*/
+#define CONFIG_NETARM_SERIAL
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x00500000 /* default load address */
#define CONFIG_SYS_HZ 900 /* decrementer freq: 2 kHz */
#else
- #define CONFIG_CMD_USB
#define CONFIG_CMD_CACHE
+ #define CONFIG_CMD_USB
- #undef CONFIG_CMD_AUTOSCRIPT
#undef CONFIG_CMD_BDI
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_MISC
+ #undef CONFIG_CMD_SOURCE
#endif
/*
* Select serial console configuration
*/
+#define CONFIG_IMX_SERIAL
#define CONFIG_IMX_SERIAL1 /* internal uart 1 */
/* #define _CONFIG_UART2 */ /* internal uart 2 */
/* #define CONFIG_SILENT_CONSOLE */ /* use this to disable output */
#define CONFIG_SYS_MEMTEST_START 0x09000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0AF00000 /* 63 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CONFIG_SYS_LOAD_ADDR 0x08800000 /* default load address */
/*#define CONFIG_SYS_HZ 1000 */
#define CONFIG_SYS_HZ 3686400
#define CONFIG_CMD_JFFS2
-#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_DHCP
+#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_PING
-#undef CONFIG_CMD_DHCP
+#undef CONFIG_CMD_SOURCE
/*
#define CONFIG_SYS_MEMTEST_START 0x08100000 /* memtest test area */
#define CONFIG_SYS_MEMTEST_END 0x08F00000
-#undef CONFIG_SYS_CLKS_IN_HZ /* use HZ for freq. display */
-
#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
#define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */
0x000b00b ->3<- -> 64MHz/4=16MHz */
#ifdef _CONFIG_UART1
+#define CONFIG_IMX_SERIAL
#define CONFIG_IMX_SERIAL1
#elif defined _CONFIG_UART2
+#define CONFIG_IMX_SERIAL
#define CONFIG_IMX_SERIAL2
#elif defined _CONFIG_UART3 | defined _CONFIG_UART4
-#define CONFIG_IMX_SERIAL_NONE
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_CLK 3686400
#define PHYS_SDRAM_1_SIZE (64 * 1024 * 1024)
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-/*
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define PHYS_FLASH_1_SIZE (1 * 1024 * 1024)
-#define CONFIG_SYS_MAX_FLASH_SECT 19
-#define CONFIG_SYS_FLASH_ERASE_TOUT (5*CONFIG_SYS_HZ) /* in ticks */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (5*CONFIG_SYS_HZ)
-
#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
#define CONFIG_DRIVER_SMC91111
#define CONFIG_SMC91111_BASE 0x04000300
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 19
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+#define CONFIG_FLASH_CFI_LEGACY
+#define CONFIG_SYS_FLASH_LEGACY_512Kx16
+
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x04000000 + (2 << 23)
#define NAND_ALLOW_ERASE_ALL 1
+#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_DRIVER_OMAP1510_I2C
+
+#define CONFIG_RTC_DS1307
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
*/
#define CONFIG_CMD_BDI
#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_FLASH
#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - \
(CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE)
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM_1 + 0x400000 /* default load address */
/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
* This time is further subdivided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE
-#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(pvt+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
#define OMAP5910_DPLL_DIV 1
#define OMAP5910_DPLL_MUL ((CONFIG_SYS_CLK_FREQ * \
/* timing informazion */
#define CONFIG_SYS_HZ (2400000 / 256) /* Timer0: 2.4Mhz + divider */
#define CONFIG_SYS_TIMERBASE 0x101E2000
-#undef CONFIG_SYS_CLKS_IN_HZ
/* serial port (PL011) configuration */
#define CONFIG_PL011_SERIAL
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00780000 /* 7,5 MB in DRAM */ /* @TODO */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x00600000 /* default load address */ /* @TODO */
#define CONFIG_SYS_HZ (CPU_CLK_FREQ/64)
#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
* This time is further subdivided by a local divisor.
*/
-#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE /* use timer 1 */
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
/* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by
* DPLL1. This time is further subdivided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
/* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by
* DPLL1. This time is further subdivided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
- #undef CONFIG_CMD_AUTOSCRIPT
+ #undef CONFIG_CMD_SOURCE
#endif
#define CONFIG_SYS_MEMTEST_START (OMAP2420_SDRC_CS0) /* memtest works on */
#define CONFIG_SYS_MEMTEST_END (OMAP2420_SDRC_CS0+SZ_31M)
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (OMAP2420_SDRC_CS0) /* default load address */
/* The 2420 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
* 32KHz clk, or from external sig. This rate is divided by a local divisor.
*/
#ifdef CONFIG_APTIX
-#define V_PVT 3
+#define V_PTV 3
#else
-#define V_PVT 7 /* use with 12MHz/128 */
+#define V_PTV 7 /* use with 12MHz/128 */
#endif
-#define CONFIG_SYS_TIMERBASE OMAP2420_GPT2
-#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_TIMERBASE OMAP2420_GPT2
+#define CONFIG_SYS_PTV V_PTV /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
"rootfstype=jffs2\0" \
"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
- "autoscr ${loadaddr}\0" \
+ "source ${loadaddr}\0" \
"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
/* load address */
* 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
* 32KHz clk, or from external sig. This rate is divided by a local divisor.
*/
-#define V_PVT 7
-
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
-#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
"rootfstype=jffs2\0" \
"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
- "autoscr ${loadaddr}\0" \
+ "source ${loadaddr}\0" \
"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, */
- /* in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
/* address */
* 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
* 32KHz clk, or from external sig. This rate is divided by a local divisor.
*/
-#define V_PVT 7
-
#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
-#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
-#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
"rootfstype=jffs2\0" \
"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
- "autoscr ${loadaddr}\0" \
+ "source ${loadaddr}\0" \
"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, */
- /* in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
/* address */
* 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
* 32KHz clk, or from external sig. This rate is divided by a local divisor.
*/
-#define V_PVT 7
-
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
-#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
"rootfstype=jffs2\0" \
"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
- "autoscr ${loadaddr}\0" \
+ "source ${loadaddr}\0" \
"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, */
- /* in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
/* address */
* 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
* 32KHz clk, or from external sig. This rate is divided by a local divisor.
*/
-#define V_PVT 7
-
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
-#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
"rootfstype=jffs2\0" \
"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
- "autoscr ${loadaddr}\0" \
+ "source ${loadaddr}\0" \
"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
/* load address */
* 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
* 32KHz clk, or from external sig. This rate is divided by a local divisor.
*/
-#define V_PVT 7
-
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
-#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
-#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
/* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by
* DPLL1. This time is further subdivided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */
/* The OMAP730 has 3 general purpose MPU timers, they can be driven by
* the RefClk (12Mhz) or by DPLL1. This time is further subdivided by a
* local divisor.
*/
-
-#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
-#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa2000000 /* default load address */
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa0800000 /* default load address */
#define CONFIG_SYS_HZ 1000
/*
* select serial console configuration
*/
+#define CONFIG_S3C24X0_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SBC2410X */
/************************************************************
#define CONFIG_SYS_MEMTEST_START 0x30000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x33000000 /* default load address */
/* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
* NAND flash settings
*/
#if defined(CONFIG_CMD_NAND)
+#define CONFIG_NAND_S3C2410
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \
+ BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L (0)
"rootpath=/opt/eldk/ppc_4xx\0" \
"bootfile=/tftpboot/sc3/uImage\0" \
"u-boot=/tftpboot/sc3/u-boot.bin\0" \
- "setup=tftp 200000 /tftpboot/sc3/setup.img;autoscr 200000\0" \
+ "setup=tftp 200000 /tftpboot/sc3/setup.img;source 200000\0" \
"kernel_addr=FFE08000\0" \
""
#undef CONFIG_BOOTCOMMAND
#include <config_cmd_default.h>
-#define CONFIG_CMD_AUTOSCRIPT
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
+#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_CACHE
#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SOURCE
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_HZ 1024 /* incrementer freq: 1kHz */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_HZ 1024 /* incrementer freq: 1kHz */
#define CONFIG_SCB9328 1 /* on a scb9328tronix board */
#undef CONFIG_USE_IRQ /* don't need use IRQ/FIQ */
+#define CONFIG_IMX_SERIAL
#define CONFIG_IMX_SERIAL1
/*
* Select serial console configuration
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
-#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
/*
#define CONFIG_SYS_MEMTEST_START 0x08100000 /* memtest test area */
#define CONFIG_SYS_MEMTEST_END 0x08F00000
-#undef CONFIG_SYS_CLKS_IN_HZ /* use HZ for freq. display */
-
#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
#define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */
/*
* select serial console configuration
*/
+#define CONFIG_SA1100_SERIAL
#define CONFIG_SERIAL3 1 /* we use SERIAL 3 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xc0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xc0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xd0000000 /* default load address */
#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
/*
* select serial console configuration
*/
+#define CONFIG_S3C24X0_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SAMSUNG */
#undef CONFIG_HWFLOW /* include RTS/CTS flow control support */
#define CONFIG_SYS_MEMTEST_START 0x0c000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0e000000 /* 32 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x0cf00000 /* default load address */
/* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
/*
* select serial console configuration
*/
+#define CONFIG_S3C24X0_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SMDK2410 */
/************************************************************
#define CONFIG_SYS_MEMTEST_START 0x30000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x33000000 /* default load address */
/* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
#if !defined(CONFIG_ENABLE_MMU)
#define CONFIG_CMD_USB 1
+#define CONFIG_USB_S3C64XX
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x74300000
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "s3c6400"
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
"bootm"
-#define CONFIG_AUTOSCRIPT
+#define CONFIG_SOURCE
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
/*
* select serial console configuration
*/
+#define CONFIG_S3C24X0_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on TRAB */
#define CONFIG_HWFLOW /* include RTS/CTS flow control support */
#define CONFIG_SYS_MEMTEST_START 0x0C000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0D000000 /* 16 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0x0CF00000 /* default load address */
#ifdef CONFIG_TRAB_50MHZ
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa1000000 /* default load address */
#define CONFIG_SYS_HZ 1000
* (NOR/OneNAND) usage and Linux kernel booting.
*/
#if defined(CONFIG_VCT_SMALL_IMAGE)
+#undef CONFIG_CMD_ASKENV
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_BEDBUG
+#undef CONFIG_CMD_CACHE
+#undef CONFIG_CMD_CONSOLE
+#undef CONFIG_CMD_CRC32
+#undef CONFIG_CMD_DHCP
+#undef CONFIG_CMD_EEPROM
#undef CONFIG_CMD_EEPROM
-#undef CONFIG_CMD_I2C
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_PING
-#undef CONFIG_CMD_SNTP
#undef CONFIG_CMD_ELF
-#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_CACHE
-#undef CONFIG_CMD_BEDBUG
-#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_FAT
+#undef CONFIG_CMD_I2C
+#undef CONFIG_CMD_I2C
#undef CONFIG_CMD_IRQ
#undef CONFIG_CMD_ITEST
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_LOADY
#undef CONFIG_CMD_MII
#undef CONFIG_CMD_MISC
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_PING
#undef CONFIG_CMD_REGINFO
+#undef CONFIG_CMD_SNTP
+#undef CONFIG_CMD_SOURCE
#undef CONFIG_CMD_STRINGS
#undef CONFIG_CMD_TERMINAL
-#undef CONFIG_CMD_ASKENV
-#undef CONFIG_CMD_CRC32
-#undef CONFIG_CMD_DHCP
-#undef CONFIG_CMD_EEPROM
-#undef CONFIG_CMD_I2C
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADY
-#undef CONFIG_CMD_BDI
#undef CONFIG_CMD_USB
-#undef CONFIG_CMD_FAT
#undef CONFIG_DRIVER_SMC911X
#undef CONFIG_SOFT_I2C
-#undef CONFIG_AUTOSCRIPT
+#undef CONFIG_SOURCE
#undef CONFIG_SYS_LONGHELP
#undef CONFIG_TIMESTAMP
#endif /* CONFIG_VCT_SMALL_IMAGE */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */
/*-----------------------------------------------------------------------
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
* This time is further subdivided by a local divisor.
*/
-#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE
-#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
#define OMAP5910_DPLL_DIV 1
#define OMAP5910_DPLL_MUL ((CONFIG_SYS_CLK_FREQ * \
*/
#include <config_cmd_default.h>
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_SOURCE
/*
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest test area */
#define CONFIG_SYS_MEMTEST_END 0xa0800000
-#undef CONFIG_SYS_CLKS_IN_HZ /* use HZ for freq. display */
-
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa1000000 /* default load address */
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa3000000 /* default load address */
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0xA0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xA0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* valid baudrates */
#define CONFIG_SYS_LOAD_ADDR 0xA0000000 /* load kernel to this address */
#define CONFIG_SYS_MEMTEST_START 0x9c000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x9c400000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
#define CONFIG_SYS_HZ 1000
/*
* NS16550 Serial Port
* originally from linux source (arch/ppc/boot/ns16550.h)
+ *
+ * Cleanup and unification
+ * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
+ *
* modified slightly to
* have addresses as offsets from CONFIG_SYS_ISA_BASE
* added a few more definitions
typedef volatile struct NS16550 *NS16550_t;
-#define FCR_FIFO_EN 0x01 /* Fifo enable */
-#define FCR_RXSR 0x02 /* Receiver soft reset */
-#define FCR_TXSR 0x04 /* Transmitter soft reset */
-
-#define MCR_DTR 0x01
-#define MCR_RTS 0x02
-#define MCR_DMA_EN 0x04
-#define MCR_TX_DFR 0x08
-#define MCR_LOOP 0x10 /* Enable loopback test mode */
-
-#define LCR_WLS_MSK 0x03 /* character length select mask */
-#define LCR_WLS_5 0x00 /* 5 bit character length */
-#define LCR_WLS_6 0x01 /* 6 bit character length */
-#define LCR_WLS_7 0x02 /* 7 bit character length */
-#define LCR_WLS_8 0x03 /* 8 bit character length */
-#define LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */
-#define LCR_PEN 0x08 /* Parity eneble */
-#define LCR_EPS 0x10 /* Even Parity Select */
-#define LCR_STKP 0x20 /* Stick Parity */
-#define LCR_SBRK 0x40 /* Set Break */
-#define LCR_BKSE 0x80 /* Bank select enable */
-#define LCR_DLAB 0x80 /* Divisor latch access bit */
-
-#define LSR_DR 0x01 /* Data ready */
-#define LSR_OE 0x02 /* Overrun */
-#define LSR_PE 0x04 /* Parity error */
-#define LSR_FE 0x08 /* Framing error */
-#define LSR_BI 0x10 /* Break */
-#define LSR_THRE 0x20 /* Xmit holding register empty */
-#define LSR_TEMT 0x40 /* Xmitter empty */
-#define LSR_ERR 0x80 /* Error */
-
-#define MSR_DCD 0x80 /* Data Carrier Detect */
-#define MSR_RI 0x40 /* Ring Indicator */
-#define MSR_DSR 0x20 /* Data Set Ready */
-#define MSR_CTS 0x10 /* Clear to Send */
-#define MSR_DDCD 0x08 /* Delta DCD */
-#define MSR_TERI 0x04 /* Trailing edge ring indicator */
-#define MSR_DDSR 0x02 /* Delta DSR */
-#define MSR_DCTS 0x01 /* Delta CTS */
+/*
+ * These are the definitions for the FIFO Control Register
+ */
+#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
+#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
+#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
+#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
+#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
+#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
+#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
+#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
+#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
+
+#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
+#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */
+
+/*
+ * These are the definitions for the Modem Control Register
+ */
+#define UART_MCR_DTR 0x01 /* DTR */
+#define UART_MCR_RTS 0x02 /* RTS */
+#define UART_MCR_OUT1 0x04 /* Out 1 */
+#define UART_MCR_OUT2 0x08 /* Out 2 */
+#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
+
+#define UART_MCR_DMA_EN 0x04
+#define UART_MCR_TX_DFR 0x08
+
+/*
+ * These are the definitions for the Line Control Register
+ *
+ * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
+ * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
+ */
+#define UART_LCR_WLS_MSK 0x03 /* character length select mask */
+#define UART_LCR_WLS_5 0x00 /* 5 bit character length */
+#define UART_LCR_WLS_6 0x01 /* 6 bit character length */
+#define UART_LCR_WLS_7 0x02 /* 7 bit character length */
+#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
+#define UART_LCR_STB 0x04 /* Number of stop Bits, off = 1, on = 1.5 or 2) */
+#define UART_LCR_PEN 0x08 /* Parity eneble */
+#define UART_LCR_EPS 0x10 /* Even Parity Select */
+#define UART_LCR_STKP 0x20 /* Stick Parity */
+#define UART_LCR_SBRK 0x40 /* Set Break */
+#define UART_LCR_BKSE 0x80 /* Bank select enable */
+#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
+
+/*
+ * These are the definitions for the Line Status Register
+ */
+#define UART_LSR_DR 0x01 /* Data ready */
+#define UART_LSR_OE 0x02 /* Overrun */
+#define UART_LSR_PE 0x04 /* Parity error */
+#define UART_LSR_FE 0x08 /* Framing error */
+#define UART_LSR_BI 0x10 /* Break */
+#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
+#define UART_LSR_TEMT 0x40 /* Xmitter empty */
+#define UART_LSR_ERR 0x80 /* Error */
+
+#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
+#define UART_MSR_RI 0x40 /* Ring Indicator */
+#define UART_MSR_DSR 0x20 /* Data Set Ready */
+#define UART_MSR_CTS 0x10 /* Clear to Send */
+#define UART_MSR_DDCD 0x08 /* Delta DCD */
+#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
+#define UART_MSR_DDSR 0x02 /* Delta DSR */
+#define UART_MSR_DCTS 0x01 /* Delta CTS */
+
+/*
+ * These are the definitions for the Interrupt Identification Register
+ */
+#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
+#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
+
+#define UART_IIR_MSI 0x00 /* Modem status interrupt */
+#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
+#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
+#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
+
+/*
+ * These are the definitions for the Interrupt Enable Register
+ */
+#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
+#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
+#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
+#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
+
#ifdef CONFIG_OMAP1510
-#define OSC_12M_SEL 0x01 /* selects 6.5 * current clk div */
+#define OSC_12M_SEL 0x01 /* selects 6.5 * current clk div */
#endif
/* useful defaults for LCR */
-#define LCR_8N1 0x03
+#define UART_LCR_8N1 0x03
void NS16550_init (NS16550_t com_port, int baud_divisor);
void NS16550_putc (NS16550_t com_port, char c);
u8 *iomem_base;
};
-#define UART_RX 0 /* In: Receive buffer (DLAB=0) */
-#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */
-#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
-
-#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */
-#define UART_IER 1 /* Out: Interrupt Enable Register */
-
-#define UART_IIR 2 /* In: Interrupt ID Register */
-#define UART_FCR 2 /* Out: FIFO Control Register */
-
-#define UART_LCR 3 /* Out: Line Control Register */
-#define UART_MCR 4 /* Out: Modem Control Register */
-#define UART_LSR 5 /* In: Line Status Register */
-#define UART_MSR 6 /* In: Modem Status Register */
-#define UART_SCR 7 /* I/O: Scratch Register */
-
-/*
- * These are the definitions for the FIFO Control Register
- * (16650 only)
- */
-#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
-#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
-#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
-#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
-#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
-#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
-#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
-#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
-#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
-
-/*
- * These are the definitions for the Line Control Register
- *
- * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
- * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
- */
-#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
-#define UART_LCR_SBC 0x40 /* Set break control */
-#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
-#define UART_LCR_EPAR 0x10 /* Even parity select */
-#define UART_LCR_PARITY 0x08 /* Parity Enable */
-#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
-#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
-#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
-#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
-#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
-
-/*
- * These are the definitions for the Line Status Register
- */
-#define UART_LSR_TEMT 0x40 /* Transmitter empty */
-#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
-#define UART_LSR_BI 0x10 /* Break interrupt indicator */
-#define UART_LSR_FE 0x08 /* Frame error indicator */
-#define UART_LSR_PE 0x04 /* Parity error indicator */
-#define UART_LSR_OE 0x02 /* Overrun error indicator */
-#define UART_LSR_DR 0x01 /* Receiver data ready */
-
-/*
- * These are the definitions for the Interrupt Identification Register
- */
-#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
-#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
-
-#define UART_IIR_MSI 0x00 /* Modem status interrupt */
-#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
-#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
-#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
-
-/*
- * These are the definitions for the Interrupt Enable Register
- */
-#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
-#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
-#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
-#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
-
-/*
- * These are the definitions for the Modem Control Register
- */
-#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
-#define UART_MCR_OUT2 0x08 /* Out2 complement */
-#define UART_MCR_OUT1 0x04 /* Out1 complement */
-#define UART_MCR_RTS 0x02 /* RTS complement */
-#define UART_MCR_DTR 0x01 /* DTR complement */
-
-/*
- * These are the definitions for the Modem Status Register
- */
-#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
-#define UART_MSR_RI 0x40 /* Ring Indicator */
-#define UART_MSR_DSR 0x20 /* Data Set Ready */
-#define UART_MSR_CTS 0x10 /* Clear to Send */
-#define UART_MSR_DDCD 0x08 /* Delta DCD */
-#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
-#define UART_MSR_DDSR 0x02 /* Delta DSR */
-#define UART_MSR_DCTS 0x01 /* Delta CTS */
-#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */
-
#endif /* __LINUX_PS2MULT_H */
projects / platform / kernel / u-boot.git / commitdiff