Remove legacy NAND and disk on chip references from boards.

Signed-off-by: Scott Wood <scottwood@freescale.com>

diff --git a/board/delta/nand.c b/board/delta/nand.c
index aff7c54..e87d502 100644 (file)
--- a/board/delta/nand.c
+++ b/board/delta/nand.c
@@ -23,7 +23,6 @@
 #include <common.h>
 
 #if defined(CONFIG_CMD_NAND)
-#if !defined(CONFIG_NAND_LEGACY)
 
 #include <nand.h>
 #include <asm/arch/pxa-regs.h>
@@ -550,7 +549,4 @@ int board_nand_init(struct nand_chip *nand)
        return 0;
 }
 
-#else
- #error "U-Boot legacy NAND support not available for Monahans DFC."
-#endif
 #endif

diff --git a/board/esd/common/auto_update.c b/board/esd/common/auto_update.c
index 33aeb46..c4a49e2 100644 (file)
--- a/board/esd/common/auto_update.c
+++ b/board/esd/common/auto_update.c
@@ -27,9 +27,6 @@
 #include <command.h>
 #include <image.h>
 #include <asm/byteorder.h>
-#if defined(CONFIG_NAND_LEGACY)
-#include <linux/mtd/nand_legacy.h>
-#endif
 #include <fat.h>
 #include <part.h>
 
@@ -58,20 +55,6 @@ extern int flash_sect_erase(ulong, ulong);
 extern int flash_sect_protect (int, ulong, ulong);
 extern int flash_write (char *, ulong, ulong);
 
-#if defined(CONFIG_CMD_NAND) && defined(CONFIG_NAND_LEGACY)
-/* references to names in cmd_nand.c */
-#define NANDRW_READ    0x01
-#define NANDRW_WRITE   0x00
-#define NANDRW_JFFS2   0x02
-#define NANDRW_JFFS2_SKIP      0x04
-extern struct nand_chip nand_dev_desc[];
-extern int nand_legacy_rw(struct nand_chip* nand, int cmd,
-                         size_t start, size_t len,
-                         size_t * retlen, u_char * buf);
-extern int nand_legacy_erase(struct nand_chip* nand, size_t ofs,
-                            size_t len, int clean);
-#endif
-
 extern block_dev_desc_t ide_dev_desc[CONFIG_SYS_IDE_MAXDEVICE];
 
 int au_check_cksum_valid(int i, long nbytes)
@@ -158,9 +141,6 @@ int au_do_update(int i, long sz)
        int off, rc;
        uint nbytes;
        int k;
-#if defined(CONFIG_CMD_NAND) && defined(CONFIG_NAND_LEGACY)
-       int total;
-#endif
 
        hdr = (image_header_t *)LOAD_ADDR;
 #if defined(CONFIG_FIT)
@@ -240,15 +220,6 @@ int au_do_update(int i, long sz)
                                au_image[i].name);
                        debug ("flash_sect_erase(%lx, %lx);\n", start, end);
                        flash_sect_erase (start, end);
-               } else {
-#if defined(CONFIG_CMD_NAND) && defined(CONFIG_NAND_LEGACY)
-                       printf ("Updating NAND FLASH with image %s\n",
-                               au_image[i].name);
-                       debug ("nand_legacy_erase(%lx, %lx);\n", start, end);
-                       rc = nand_legacy_erase (nand_dev_desc, start,
-                                               end - start + 1, 0);
-                       debug ("nand_legacy_erase returned %x\n", rc);
-#endif
                }
 
                udelay(10000);
@@ -273,18 +244,7 @@ int au_do_update(int i, long sz)
                        rc = flash_write ((char *)addr, start,
                                          (nbytes + 1) & ~1);
                } else {
-#if defined(CONFIG_CMD_NAND) && defined(CONFIG_NAND_LEGACY)
-                       debug ("nand_legacy_rw(%p, %lx, %x)\n",
-                              addr, start, nbytes);
-                       rc = nand_legacy_rw (nand_dev_desc,
-                                            NANDRW_WRITE | NANDRW_JFFS2,
-                                            start, nbytes, (size_t *)&total,
-                                            (uchar *)addr);
-                       debug ("nand_legacy_rw: ret=%x total=%d nbytes=%d\n",
-                              rc, total, nbytes);
-#else
                        rc = -1;
-#endif
                }
                if (rc != 0) {
                        printf ("Flashing failed due to error %d\n", rc);
@@ -297,16 +257,6 @@ int au_do_update(int i, long sz)
                if (au_image[i].type != AU_NAND) {
                        rc = crc32 (0, (uchar *)(start + off),
                                    image_get_data_size (hdr));
-               } else {
-#if defined(CONFIG_CMD_NAND) && defined(CONFIG_NAND_LEGACY)
-                       rc = nand_legacy_rw (nand_dev_desc,
-                                            NANDRW_READ | NANDRW_JFFS2 |
-                                            NANDRW_JFFS2_SKIP,
-                                            start, nbytes, (size_t *)&total,
-                                            (uchar *)addr);
-                       rc = crc32 (0, (uchar *)(addr + off),
-                                   image_get_data_size (hdr));
-#endif
                }
                if (rc != image_get_dcrc (hdr)) {
                        printf ("Image %s Bad Data Checksum After COPY\n",

diff --git a/board/g2000/g2000.c b/board/g2000/g2000.c
index 218f1be..f6f4719 100644 (file)
--- a/board/g2000/g2000.c
+++ b/board/g2000/g2000.c
@@ -148,21 +148,6 @@ phys_size_t initdram (int board_type)
        return ret;
 }
 
-
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-       nand_probe(CONFIG_SYS_NAND_BASE);
-       if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-               print_size(nand_dev_desc[0].totlen, "\n");
-       }
-}
-#endif
-
-
 #if 0 /* test-only !!! */
 int do_dumpebc(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {

diff --git a/board/netphone/netphone.c b/board/netphone/netphone.c
index 53d3172..ce5f051 100644 (file)
--- a/board/netphone/netphone.c
+++ b/board/netphone/netphone.c
@@ -597,22 +597,6 @@ int board_early_init_f(void)
        return 0;
 }
 
-#if defined(CONFIG_CMD_NAND)
-
-#include <linux/mtd/nand_legacy.h>
-
-extern ulong nand_probe(ulong physadr);
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-       unsigned long totlen;
-
-       totlen = nand_probe(CONFIG_SYS_NAND_BASE);
-       printf ("%4lu MB\n", totlen >> 20);
-}
-#endif
-
 #ifdef CONFIG_HW_WATCHDOG
 
 void hw_watchdog_reset(void)

diff --git a/board/netta/netta.c b/board/netta/netta.c
index 02fd94c..38c9d89 100644 (file)
--- a/board/netta/netta.c
+++ b/board/netta/netta.c
@@ -555,21 +555,6 @@ int board_early_init_f(void)
        return 0;
 }
 
-#if defined(CONFIG_CMD_NAND) && defined(CONFIG_NAND_LEGACY)
-
-#include <linux/mtd/nand_legacy.h>
-
-extern ulong nand_probe(ulong physadr);
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-       unsigned long totlen = nand_probe(CONFIG_SYS_NAND_BASE);
-
-       printf ("%4lu MB\n", totlen >> 20);
-}
-#endif
-
 #if defined(CONFIG_CMD_PCMCIA)
 
 int pcmcia_init(void)

diff --git a/board/netta2/netta2.c b/board/netta2/netta2.c
index 2ce33cf..3b0191d 100644 (file)
--- a/board/netta2/netta2.c
+++ b/board/netta2/netta2.c
@@ -595,22 +595,6 @@ int board_early_init_f(void)
        return 0;
 }
 
-#if defined(CONFIG_CMD_NAND)
-
-#include <linux/mtd/nand_legacy.h>
-
-extern ulong nand_probe(ulong physadr);
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-       unsigned long totlen;
-
-       totlen = nand_probe(CONFIG_SYS_NAND_BASE);
-       printf ("%4lu MB\n", totlen >> 20);
-}
-#endif
-
 #ifdef CONFIG_HW_WATCHDOG
 
 void hw_watchdog_reset(void)

diff --git a/board/netvia/netvia.c b/board/netvia/netvia.c
index 0b032c4..5606996 100644 (file)
--- a/board/netvia/netvia.c
+++ b/board/netvia/netvia.c
@@ -415,18 +415,3 @@ int board_early_init_f(void)
 
        return 0;
 }
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <linux/mtd/nand_legacy.h>
-
-extern ulong nand_probe(ulong physadr);
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-       unsigned long totlen = nand_probe(CONFIG_SYS_NAND_BASE);
-
-       printf ("%4lu MB\n", totlen >> 20);
-}
-#endif

diff --git a/board/omap2420h4/omap2420h4.c b/board/omap2420h4/omap2420h4.c
index 0fe9380..8d18239 100644 (file)
--- a/board/omap2420h4/omap2420h4.c
+++ b/board/omap2420h4/omap2420h4.c
@@ -31,10 +31,6 @@
 #include <asm/arch/mem.h>
 #include <i2c.h>
 #include <asm/mach-types.h>
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-#endif
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -846,22 +842,3 @@ void update_mux(u32 btype,u32 mtype)
                }
        }
 }
-
-#if defined(CONFIG_CMD_NAND)
-void nand_init(void)
-{
-    extern flash_info_t flash_info[];
-
-    nand_probe(CONFIG_SYS_NAND_ADDR);
-    if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-               print_size(nand_dev_desc[0].totlen, "\n");
-    }
-
-#ifdef CONFIG_SYS_JFFS2_MEM_NAND
-    flash_info[CONFIG_SYS_JFFS2_FIRST_BANK].flash_id = nand_dev_desc[0].id;
-    flash_info[CONFIG_SYS_JFFS2_FIRST_BANK].size = 1024*1024*2;      /* only read kernel single meg partition */
-       flash_info[CONFIG_SYS_JFFS2_FIRST_BANK].sector_count = 1024;   /* 1024 blocks in 16meg chip (use less for raw/copied partition) */
-    flash_info[CONFIG_SYS_JFFS2_FIRST_BANK].start[0] = 0x80200000; /* ?, ram for now, open question, copy to RAM or adapt for NAND */
-#endif
-}
-#endif

diff --git a/board/samsung/smdk6400/smdk6400.c b/board/samsung/smdk6400/smdk6400.c
index bd2e45a..52cd174 100644 (file)
--- a/board/samsung/smdk6400/smdk6400.c
+++ b/board/samsung/smdk6400/smdk6400.c
@@ -107,17 +107,6 @@ ulong virt_to_phy_smdk6400(ulong addr)
 }
 #endif
 
-#if defined(CONFIG_CMD_NAND) && defined(CONFIG_SYS_NAND_LEGACY)
-#include <linux/mtd/nand.h>
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-void nand_init(void)
-{
-       nand_probe(CONFIG_SYS_NAND_BASE);
-       if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN)
-               print_size(nand_dev_desc[0].totlen, "\n");
-}
-#endif
-
 ulong board_flash_get_legacy (ulong base, int banknum, flash_info_t *info)
 {
        if (banknum == 0) {     /* non-CFI boot flash */

diff --git a/board/sixnet/sixnet.c b/board/sixnet/sixnet.c
index 6e39b01..edb5d13 100644 (file)
--- a/board/sixnet/sixnet.c
+++ b/board/sixnet/sixnet.c
@@ -33,11 +33,6 @@
 # include <status_led.h>
 #endif
 
-#if defined(CONFIG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-#endif
-
 DECLARE_GLOBAL_DATA_PTR;
 
 #define ORMASK(size) ((-size) & OR_AM_MSK)

diff --git a/board/stxxtc/stxxtc.c b/board/stxxtc/stxxtc.c
index a1a36c4..717dbe2 100644 (file)
--- a/board/stxxtc/stxxtc.c
+++ b/board/stxxtc/stxxtc.c
@@ -574,22 +574,6 @@ int board_early_init_f(void)
        return 0;
 }
 
-#if defined(CONFIG_CMD_NAND)
-
-#include <linux/mtd/nand_legacy.h>
-
-extern ulong nand_probe(ulong physadr);
-extern struct nand_chip nand_dev_desc[CONFIG_SYS_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-       unsigned long totlen;
-
-       totlen = nand_probe(CONFIG_SYS_NAND_BASE);
-       printf ("%4lu MB\n", totlen >> 20);
-}
-#endif
-
 #ifdef CONFIG_HW_WATCHDOG
 
 void hw_watchdog_reset(void)

diff --git a/board/zylonite/nand.c b/board/zylonite/nand.c
index 899445e..bec54cb 100644 (file)
--- a/board/zylonite/nand.c
+++ b/board/zylonite/nand.c
@@ -23,7 +23,6 @@
 #include <common.h>
 
 #if defined(CONFIG_CMD_NAND)
-#ifdef CONFIG_NEW_NAND_CODE
 
 #include <nand.h>
 #include <asm/arch/pxa-regs.h>
@@ -554,7 +553,4 @@ int board_nand_init(struct nand_chip *nand)
        return 0;
 }
 
-#else
- #error "U-Boot legacy NAND support not available for Monahans DFC."
-#endif
 #endif

diff --git a/include/configs/BMW.h b/include/configs/BMW.h
index 24ffb00..98f6396 100644 (file)
--- a/include/configs/BMW.h
+++ b/include/configs/BMW.h
@@ -81,13 +81,9 @@
 #include <config_cmd_default.h>
 
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_ELF
 
 
-/* CONFIG_CMD_DOC required legacy NAND support */
-#define CONFIG_NAND_LEGACY
-
 #if 0
 #define CONFIG_PCI             1
 #define CONFIG_PCI_PNP         1       /* PCI plug-and-play */

diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h
index 39f41e6..229a513 100644 (file)
--- a/include/configs/CATcenter.h
+++ b/include/configs/CATcenter.h
@@ -209,16 +209,8 @@
 
 /* For CATcenter there is only NAND on the module */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
-#define SECTORSIZE 512
 #define NAND_NO_RB
 
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-
 #define CONFIG_SYS_NAND0_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
 #define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
 #define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */

diff --git a/include/configs/CPU86.h b/include/configs/CPU86.h
index cf21fd9..6d76d9f 100644 (file)
--- a/include/configs/CPU86.h
+++ b/include/configs/CPU86.h
@@ -146,15 +146,6 @@
 #undef CONFIG_WATCHDOG                 /* watchdog disabled            */
 
 /*-----------------------------------------------------------------------
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices    */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
-/*-----------------------------------------------------------------------
  * Miscellaneous configuration options
  */
 
@@ -179,7 +170,6 @@
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_NFS

diff --git a/include/configs/CPU87.h b/include/configs/CPU87.h
index 489378a..83b010c 100644 (file)
--- a/include/configs/CPU87.h
+++ b/include/configs/CPU87.h
@@ -182,7 +182,6 @@
 
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 
@@ -190,9 +189,6 @@
     #define CONFIG_CMD_PCI
 #endif
 
-
-#define CONFIG_NAND_LEGACY
-
 /*
  * Miscellaneous configurable options
  */

diff --git a/include/configs/G2000.h b/include/configs/G2000.h
index bf9fd82..6819c3e 100644 (file)
--- a/include/configs/G2000.h
+++ b/include/configs/G2000.h
@@ -196,32 +196,12 @@
  *-----------------------------------------------------------------------
  */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
 
 #define CONFIG_SYS_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
 #define CONFIG_SYS_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
 #define CONFIG_SYS_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
 #define CONFIG_SYS_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
 
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CONFIG_SYS_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
 #endif
 
 /*-----------------------------------------------------------------------

diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h
index 8f18ab2..12f879a 100644 (file)
--- a/include/configs/GEN860T.h
+++ b/include/configs/GEN860T.h
@@ -244,10 +244,6 @@
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_BEDBUG
 
-#if !defined(CONFIG_SC)
-    #define CONFIG_CMD_DOC
-#endif
-
 #ifdef CONFIG_POST
 #define CONFIG_CMD_DIAG
 #endif
@@ -279,9 +275,6 @@
 #define CONFIG_FPGA_VIRTEX2
 #define CONFIG_SYS_FPGA_PROG_FEEDBACK
 
-
-#define CONFIG_NAND_LEGACY
-
 /*
  * Verbose help from command monitor.
  */
@@ -738,16 +731,6 @@
 #define BOOTFLAG_WARM  0x02    /* Software reboot                                      */
 
 /*
- * Disk On Chip (millenium) configuration
- */
-#if !defined(CONFIG_SC)
-#define CONFIG_SYS_MAX_DOC_DEVICE      1
-#undef CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-#undef CONFIG_SYS_DOC_PASSIVE_PROBE
-#endif
-
-/*
  * FEC interrupt assignment
  */
 #define FEC_INTERRUPT   SIU_LEVEL1

diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h
index 8315cfe..264e0e7 100644 (file)
--- a/include/configs/MIP405.h
+++ b/include/configs/MIP405.h
@@ -84,12 +84,9 @@
 
 #if !defined(CONFIG_MIP405T)
     #define CONFIG_CMD_USB
-    #define CONFIG_CMD_DOC
 #endif
 
 
-#define CONFIG_NAND_LEGACY
-
 #define         CONFIG_SYS_HUSH_PARSER
 #define         CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 /**************************************************************
@@ -384,13 +381,6 @@
 #define CONFIG_ISO_PARTITION /* Experimental */
 
 /************************************************************
- * Disk-On-Chip configuration
- ************************************************************/
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices            */
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-/************************************************************
  * Keyboard support
  ************************************************************/
 #undef CONFIG_ISA_KEYBOARD

diff --git a/include/configs/NETPHONE.h b/include/configs/NETPHONE.h
index 796938a..8a197ad 100644 (file)
--- a/include/configs/NETPHONE.h
+++ b/include/configs/NETPHONE.h
@@ -497,95 +497,9 @@
 #define DSP_BASE       0xF1000000
 #define NAND_BASE      0xF1010000
 
-/****************************************************************/
-
-/* NAND */
-#define CONFIG_NAND_LEGACY
-#define CONFIG_SYS_NAND_BASE           NAND_BASE
-#define CONFIG_MTD_NAND_ECC_JFFS2
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_MTD_NAND_UNSAFE
-
-#define CONFIG_SYS_MAX_NAND_DEVICE     1
-
-#define SECTORSIZE             512
-#define ADDR_COLUMN            1
-#define ADDR_PAGE              2
-#define ADDR_COLUMN_PAGE       3
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS                1
-
-/* ALE = PD17, CLE = PE18, CE = PE20, F_RY_BY = PE31 */
-#define NAND_DISABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) |=  (1 << (31 - 20)); \
-       } while(0)
-
-#define NAND_ENABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 20)); \
-       } while(0)
-
-#define NAND_CTL_CLRALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 17)); \
-       } while(0)
-
-#define NAND_CTL_SETALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) |=  (1 << (31 - 17)); \
-       } while(0)
-
-#define NAND_CTL_CLRCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 18)); \
-       } while(0)
-
-#define NAND_CTL_SETCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) |=  (1 << (31 - 18)); \
-       } while(0)
-
-#if CONFIG_NETPHONE_VERSION == 1
-#define NAND_WAIT_READY(nand) \
-       do { \
-               int _tries = 0; \
-               while ((((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat & (1 << (31 - 31))) == 0) \
-                       if (++_tries > 100000) \
-                               break; \
-       } while (0)
-#elif CONFIG_NETPHONE_VERSION == 2
-#define NAND_WAIT_READY(nand) \
-       do { \
-               int _tries = 0; \
-               while ((((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat & (1 << (15 - 15))) == 0) \
-                       if (++_tries > 100000) \
-                               break; \
-       } while (0)
-#endif
-
-#define WRITE_NAND_COMMAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND_ADDRESS(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define READ_NAND(adr) \
-       ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr)))
-
 /*****************************************************************************/
 
 #define CONFIG_SYS_DIRECT_FLASH_TFTP
-#define CONFIG_SYS_DIRECT_NAND_TFTP
 
 /*****************************************************************************/
 

diff --git a/include/configs/NETTA.h b/include/configs/NETTA.h
index 724e807..dda6179 100644 (file)
--- a/include/configs/NETTA.h
+++ b/include/configs/NETTA.h
@@ -616,105 +616,6 @@
 #define ER_BASE                0xF1020000
 #define DUMMY_BASE     0xF1FF0000
 
-/****************************************************************/
-
-/* NAND */
-#define CONFIG_NAND_LEGACY
-#define CONFIG_SYS_NAND_BASE                   NAND_BASE
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_MTD_NAND_UNSAFE
-
-#define CONFIG_SYS_MAX_NAND_DEVICE             1
-/* #define NAND_NO_RB */
-
-#define SECTORSIZE             512
-#define ADDR_COLUMN            1
-#define ADDR_PAGE              2
-#define ADDR_COLUMN_PAGE       3
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS                1
-
-/* ALE = PD3, CLE = PD4, CE = PD5, F_RY_BY = PC13 */
-#define NAND_DISABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |=  (1 << (15 - 5)); \
-       } while(0)
-
-#define NAND_ENABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 5)); \
-       } while(0)
-
-#define NAND_CTL_CLRALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 3)); \
-       } while(0)
-
-#define NAND_CTL_SETALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |=  (1 << (15 - 3)); \
-       } while(0)
-
-#define NAND_CTL_CLRCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 4)); \
-       } while(0)
-
-#define NAND_CTL_SETCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |=  (1 << (15 - 4)); \
-       } while(0)
-
-#ifndef NAND_NO_RB
-#define NAND_WAIT_READY(nand) \
-       do { \
-               while ((((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat & (1 << (15 - 13))) == 0) { \
-                       WATCHDOG_RESET(); \
-               } \
-       } while (0)
-#else
-#define NAND_WAIT_READY(nand) udelay(12)
-#endif
-
-#define WRITE_NAND_COMMAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND_ADDRESS(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define READ_NAND(adr) \
-       ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr)))
-
-#define CONFIG_JFFS2_NAND      1                       /* jffs2 on nand support */
-#define NAND_CACHE_PAGES       16                      /* size of nand cache in 512 bytes pages */
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV               "nand0"
-#define CONFIG_JFFS2_PART_SIZE         0x00100000
-#define CONFIG_JFFS2_PART_OFFSET       0x00200000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT         "nand0=netta-nand"
-#define MTDPARTS_DEFAULT       "mtdparts=netta-nand:1m@2m(jffs2)"
-*/
-
 /*****************************************************************************/
 
 #define CONFIG_SYS_DIRECT_FLASH_TFTP

diff --git a/include/configs/NETTA2.h b/include/configs/NETTA2.h
index a14b2dd..167285e 100644 (file)
--- a/include/configs/NETTA2.h
+++ b/include/configs/NETTA2.h
@@ -498,95 +498,9 @@
 #define DSP_BASE       0xF1000000
 #define NAND_BASE      0xF1010000
 
-/****************************************************************/
-
-/* NAND */
-#define CONFIG_NAND_LEGACY
-#define CONFIG_SYS_NAND_BASE           NAND_BASE
-#define CONFIG_MTD_NAND_ECC_JFFS2
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_MTD_NAND_UNSAFE
-
-#define CONFIG_SYS_MAX_NAND_DEVICE     1
-
-#define SECTORSIZE             512
-#define ADDR_COLUMN            1
-#define ADDR_PAGE              2
-#define ADDR_COLUMN_PAGE       3
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS                1
-
-/* ALE = PD17, CLE = PE18, CE = PE20, F_RY_BY = PE31 */
-#define NAND_DISABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) |=  (1 << (31 - 20)); \
-       } while(0)
-
-#define NAND_ENABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 20)); \
-       } while(0)
-
-#define NAND_CTL_CLRALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 17)); \
-       } while(0)
-
-#define NAND_CTL_SETALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) |=  (1 << (31 - 17)); \
-       } while(0)
-
-#define NAND_CTL_CLRCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 18)); \
-       } while(0)
-
-#define NAND_CTL_SETCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat) |=  (1 << (31 - 18)); \
-       } while(0)
-
-#if CONFIG_NETTA2_VERSION == 1
-#define NAND_WAIT_READY(nand) \
-       do { \
-               int _tries = 0; \
-               while ((((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat & (1 << (31 - 31))) == 0) \
-                       if (++_tries > 100000) \
-                               break; \
-       } while (0)
-#elif CONFIG_NETTA2_VERSION == 2
-#define NAND_WAIT_READY(nand) \
-       do { \
-               int _tries = 0; \
-               while ((((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat & (1 << (15 - 15))) == 0) \
-                       if (++_tries > 100000) \
-                               break; \
-       } while (0)
-#endif
-
-#define WRITE_NAND_COMMAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND_ADDRESS(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define READ_NAND(adr) \
-       ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr)))
-
 /*****************************************************************************/
 
 #define CONFIG_SYS_DIRECT_FLASH_TFTP
-#define CONFIG_SYS_DIRECT_NAND_TFTP
 
 /*****************************************************************************/
 

diff --git a/include/configs/NETVIA.h b/include/configs/NETVIA.h
index f97bdcb..b9cf621 100644 (file)
--- a/include/configs/NETVIA.h
+++ b/include/configs/NETVIA.h
@@ -393,80 +393,6 @@
 
 #endif
 
-/*****************************************************************************/
-
-#define CONFIG_NAND_LEGACY
-
-#if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2
-
-/* NAND */
-#define CONFIG_SYS_NAND_BASE                   NAND_BASE
-#define CONFIG_MTD_NAND_ECC_JFFS2
-
-#define CONFIG_SYS_MAX_NAND_DEVICE             1
-
-#define SECTORSIZE             512
-#define ADDR_COLUMN            1
-#define ADDR_PAGE              2
-#define ADDR_COLUMN_PAGE       3
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS                1
-
-#define NAND_DISABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |=  0x0040; \
-       } while(0)
-
-#define NAND_ENABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~0x0040; \
-       } while(0)
-
-#define NAND_CTL_CLRALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~0x0100; \
-       } while(0)
-
-#define NAND_CTL_SETALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |=  0x0100; \
-       } while(0)
-
-#define NAND_CTL_CLRCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~0x0080; \
-       } while(0)
-
-#define NAND_CTL_SETCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |=  0x0080; \
-       } while(0)
-
-#define NAND_WAIT_READY(nand) \
-       do { \
-               while ((((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat & 0x100) == 0) \
-                       ; \
-       } while (0)
-
-#define WRITE_NAND_COMMAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND_ADDRESS(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define READ_NAND(adr) \
-       ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr)))
-
-#endif
 
 /*****************************************************************************/
 

diff --git a/include/configs/PCIPPC2.h b/include/configs/PCIPPC2.h
index 5951d00..99a8c4a 100644 (file)
--- a/include/configs/PCIPPC2.h
+++ b/include/configs/PCIPPC2.h
@@ -75,7 +75,6 @@
 #define CONFIG_CMD_BSP
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
@@ -84,8 +83,6 @@
 #define CONFIG_PCI             1
 #define CONFIG_PCI_PNP         1       /* PCI plug-and-play */
 
-#define CONFIG_NAND_LEGACY
-
 /*
  * Miscellaneous configurable options
  */
@@ -251,15 +248,6 @@
 #define BOOTFLAG_WARM          0x02    /* Software reboot                      */
 
 /*-----------------------------------------------------------------------
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices            */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#undef CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
-/*-----------------------------------------------------------------------
   RTC m48t59
 */
 #define CONFIG_RTC_MK48T59

diff --git a/include/configs/PCIPPC6.h b/include/configs/PCIPPC6.h
index a683a8f..66e6d24 100644 (file)
--- a/include/configs/PCIPPC6.h
+++ b/include/configs/PCIPPC6.h
@@ -75,7 +75,6 @@
 #define CONFIG_CMD_BSP
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
@@ -86,8 +85,6 @@
 #define CONFIG_PCI             1
 #define CONFIG_PCI_PNP         1       /* PCI plug-and-play */
 
-#define CONFIG_NAND_LEGACY
-
 /*
  * Miscellaneous configurable options
  */
@@ -253,15 +250,6 @@
 #define BOOTFLAG_WARM          0x02    /* Software reboot                      */
 
 /*-----------------------------------------------------------------------
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices            */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#undef CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
-/*-----------------------------------------------------------------------
   RTC m48t59
 */
 #define CONFIG_RTC_MK48T59

diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h
index e214d70..e15ed4a 100644 (file)
--- a/include/configs/PIP405.h
+++ b/include/configs/PIP405.h
@@ -71,14 +71,10 @@
 #define CONFIG_CMD_USB
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_SAVES
 #define CONFIG_CMD_BSP
 
-
-#define CONFIG_NAND_LEGACY
-
 #define         CONFIG_SYS_HUSH_PARSER
 #define         CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 /**************************************************************

diff --git a/include/configs/PM520.h b/include/configs/PM520.h
index ff73ef9..f9687d2 100644 (file)
--- a/include/configs/PM520.h
+++ b/include/configs/PM520.h
@@ -86,12 +86,6 @@
 #define CONFIG_USB_STORAGE
 #endif
 
-#if !defined(CONFIG_BOOT_ROM)
-/* DoC requires legacy NAND for now */
-#define CONFIG_NAND_LEGACY
-#endif
-
-
 /*
  * BOOTP options
  */
@@ -117,10 +111,6 @@
 #define CONFIG_CMD_SNTP
 #define CONFIG_CMD_USB
 
-#if !defined(CONFIG_BOOT_ROM)
-#define CONFIG_CMD_DOC
-#endif
-
 #if defined(CONFIG_MPC5200)
 #define CONFIG_CMD_PCI
 #endif
@@ -186,15 +176,6 @@
 #define CONFIG_RTC_PCF8563
 #define CONFIG_SYS_I2C_RTC_ADDR                0x51
 
-/*
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices    */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
 #define CONFIG_SYS_DOC_BASE            0xE0000000
 #define CONFIG_SYS_DOC_SIZE            0x00100000
 

diff --git a/include/configs/PM826.h b/include/configs/PM826.h
index b58f529..636bd26 100644 (file)
--- a/include/configs/PM826.h
+++ b/include/configs/PM826.h
@@ -169,7 +169,6 @@
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_NFS
@@ -179,19 +178,6 @@
 #define CONFIG_CMD_PCI
 #endif
 
-
-#define CONFIG_NAND_LEGACY
-
-/*
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices    */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
 /*
  * Miscellaneous configurable options
  */

diff --git a/include/configs/PM828.h b/include/configs/PM828.h
index 96c86f7..9d620af 100644 (file)
--- a/include/configs/PM828.h
+++ b/include/configs/PM828.h
@@ -169,7 +169,6 @@
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_NFS
@@ -179,18 +178,6 @@
 #define CONFIG_CMD_PCI
 #endif
 
-
-/*
- * Disk-On-Chip configuration
- */
-#define CONFIG_NAND_LEGACY
-
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices    */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
 /*
  * Miscellaneous configurable options
  */

diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h
index 16baf8c..9e54bf8 100644 (file)
--- a/include/configs/PPChameleonEVB.h
+++ b/include/configs/PPChameleonEVB.h
@@ -309,32 +309,6 @@
        } \
 } while(0)
 
-#if 0
-#define SECTORSIZE 512
-#define NAND_NO_RB
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-
-#ifdef NAND_NO_RB
-/* constant delay (see also tR in the datasheet) */
-#define NAND_WAIT_READY(nand) do { \
-       udelay(12); \
-} while (0)
-#else
-/* use the R/B pin */
-/* TBD */
-#endif
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-#endif
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------

diff --git a/include/configs/RBC823.h b/include/configs/RBC823.h
index f36244d..00ac6cf 100644 (file)
--- a/include/configs/RBC823.h
+++ b/include/configs/RBC823.h
@@ -114,7 +114,6 @@
 #define CONFIG_CMD_CDP
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_FAT
@@ -329,14 +328,6 @@
 
 #endif
 
-/************************************************************
- * Disk-On-Chip configuration
- ************************************************************/
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices            */
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
 /*-----------------------------------------------------------------------
  *
  *-----------------------------------------------------------------------

diff --git a/include/configs/SXNI855T.h b/include/configs/SXNI855T.h
index cac04b4..8ee8cbf 100644 (file)
--- a/include/configs/SXNI855T.h
+++ b/include/configs/SXNI855T.h
@@ -163,75 +163,8 @@
 
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NAND
 #define CONFIG_CMD_DATE
 
-
-#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition */
-#undef CONFIG_CMD_MTDPARTS
-
-/*
-#define CONFIG_JFFS2_DEV               "nor0"
-#define CONFIG_JFFS2_PART_SIZE         0x00780000
-#define CONFIG_JFFS2_PART_OFFSET       0x00080000
-*/
-
-#define CONFIG_JFFS2_DEV               "nand0"
-#define CONFIG_JFFS2_PART_SIZE         0x00200000
-#define CONFIG_JFFS2_PART_OFFSET       0x00000000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT         "nor0=sixnet-0,nand0=sixnet-nand"
-#define MTDPARTS_DEFAULT       "mtdparts=sixnet-0:7680k@512k();sixnet-nand:2m(jffs2-nand)"
-*/
-
-/* NAND flash support */
-#define CONFIG_NAND_LEGACY
-#define CONFIG_MTD_NAND_ECC_JFFS2
-#define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices   */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-
-/* DFBUSY is available on Port C, bit 12; 0 if busy */
-#define NAND_WAIT_READY(nand)  \
-       while (!(((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat & 0x0008));
-#define WRITE_NAND_COMMAND(d, adr) WRITE_NAND((d), (adr))
-#define WRITE_NAND_ADDRESS(d, adr) WRITE_NAND((d), (adr))
-#define WRITE_NAND(d, adr)     \
-        do { (*(volatile uint8_t *)(adr) = (uint8_t)(d)); } while (0)
-#define READ_NAND(adr) (*(volatile uint8_t *)(adr))
-#define        CLE_LO  0x01    /* 0 selects CLE mode (CLE high) */
-#define        ALE_LO  0x02    /* 0 selects ALE mode (ALE high) */
-#define        CE_LO   0x04    /* 1 selects chip (CE low) */
-#define        nand_setcr(cr, val) do {*(volatile uint8_t*)(cr) = (val);} while (0)
-#define NAND_DISABLE_CE(nand) \
-       nand_setcr((nand)->IO_ADDR + 1, ALE_LO | CLE_LO)
-#define NAND_ENABLE_CE(nand) \
-       nand_setcr((nand)->IO_ADDR + 1, CE_LO | ALE_LO | CLE_LO)
-#define NAND_CTL_CLRALE(nandptr) \
-       nand_setcr((nandptr) + 1, CE_LO | ALE_LO | CLE_LO)
-#define NAND_CTL_SETALE(nandptr) \
-       nand_setcr((nandptr) + 1, CE_LO | CLE_LO)
-#define NAND_CTL_CLRCLE(nandptr) \
-       nand_setcr((nandptr) + 1, CE_LO | ALE_LO | CLE_LO)
-#define NAND_CTL_SETCLE(nandptr) \
-       nand_setcr((nandptr) + 1, CE_LO | ALE_LO)
-
 /*
  * Miscellaneous configurable options
  */

diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index 6f13c63..d44fb07 100644 (file)
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -351,8 +351,6 @@
 /* NAND FLASH */
 #ifdef CONFIG_NAND
 
-#undef CONFIG_NAND_LEGACY
-
 #define CONFIG_NAND_FSL_UPM    1
 
 #define        CONFIG_MTD_NAND_ECC_JFFS2       1       /* use JFFS2 ECC        */

diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h
index de3092d..0480913 100644 (file)
--- a/include/configs/VCMA9.h
+++ b/include/configs/VCMA9.h
@@ -246,42 +246,4 @@
 
 #define MULTI_PURPOSE_SOCKET_ADDR 0x08000000
 
-/*-----------------------------------------------------------------------
- * NAND flash settings
- */
-#if defined(CONFIG_CMD_NAND)
-
-#define CONFIG_NAND_LEGACY
-#define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-
-#define NAND_WAIT_READY(nand)  NF_WaitRB()
-
-#define NAND_DISABLE_CE(nand)  NF_SetCE(NFCE_HIGH)
-#define NAND_ENABLE_CE(nand)   NF_SetCE(NFCE_LOW)
-
-
-#define WRITE_NAND_COMMAND(d, adr)     NF_Cmd(d)
-#define WRITE_NAND_COMMANDW(d, adr)    NF_CmdW(d)
-#define WRITE_NAND_ADDRESS(d, adr)     NF_Addr(d)
-#define WRITE_NAND(d, adr)             NF_Write(d)
-#define READ_NAND(adr)                 NF_Read()
-/* the following functions are NOP's because S3C24X0 handles this in hardware */
-#define NAND_CTL_CLRALE(nandptr)
-#define NAND_CTL_SETALE(nandptr)
-#define NAND_CTL_CLRCLE(nandptr)
-#define NAND_CTL_SETCLE(nandptr)
-
-#define CONFIG_MTD_NAND_VERIFY_WRITE   1
-#define CONFIG_MTD_NAND_ECC_JFFS2      1
-
-#endif
-
 #endif /* __CONFIG_H */

diff --git a/include/configs/at91rm9200dk.h b/include/configs/at91rm9200dk.h
index 56128c1..2017b66 100644 (file)
--- a/include/configs/at91rm9200dk.h
+++ b/include/configs/at91rm9200dk.h
@@ -117,38 +117,8 @@
 
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-
-#define CONFIG_NAND_LEGACY
-
-#define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-
-#define AT91_SMART_MEDIA_ALE (1 << 22) /* our ALE is AD22 */
-#define AT91_SMART_MEDIA_CLE (1 << 21) /* our CLE is AD21 */
 
 #include <asm/arch/AT91RM9200.h>       /* needed for port definitions */
-#define NAND_DISABLE_CE(nand) do { *AT91C_PIOC_SODR = AT91C_PIO_PC0;} while(0)
-#define NAND_ENABLE_CE(nand) do { *AT91C_PIOC_CODR = AT91C_PIO_PC0;} while(0)
-
-#define NAND_WAIT_READY(nand) while (!(*AT91C_PIOC_PDSR & AT91C_PIO_PC2))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | AT91_SMART_MEDIA_CLE) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | AT91_SMART_MEDIA_ALE) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-/* the following are NOP's in our implementation */
-#define NAND_CTL_CLRALE(nandptr)
-#define NAND_CTL_SETALE(nandptr)
-#define NAND_CTL_CLRCLE(nandptr)
-#define NAND_CTL_SETCLE(nandptr)
 
 #define CONFIG_NR_DRAM_BANKS 1
 #define PHYS_SDRAM 0x20000000

diff --git a/include/configs/csb637.h b/include/configs/csb637.h
index e1cdc7f..7a57696 100644 (file)
--- a/include/configs/csb637.h
+++ b/include/configs/csb637.h
@@ -121,38 +121,6 @@
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_PING
 
-#ifdef NAND_SUPPORT_HAS_BEEN_FIXED     /* NAND support is broken / unimplemented */
-
-#define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-
-#define AT91_SMART_MEDIA_ALE (1 << 22) /* our ALE is AD22 */
-#define AT91_SMART_MEDIA_CLE (1 << 21) /* our CLE is AD21 */
-
-#include <asm/arch/AT91RM9200.h>       /* needed for port definitions */
-#define NAND_DISABLE_CE(nand) do { *AT91C_PIOC_SODR = AT91C_PIO_PC0;} while(0)
-#define NAND_ENABLE_CE(nand) do { *AT91C_PIOC_CODR = AT91C_PIO_PC0;} while(0)
-
-#define NAND_WAIT_READY(nand) while (!(*AT91C_PIOC_PDSR & AT91C_PIO_PC2))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | AT91_SMART_MEDIA_CLE) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | AT91_SMART_MEDIA_ALE) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-/* the following are NOP's in our implementation */
-#define NAND_CTL_CLRALE(nandptr)
-#define NAND_CTL_SETALE(nandptr)
-#define NAND_CTL_CLRCLE(nandptr)
-#define NAND_CTL_SETCLE(nandptr)
-
-#endif /* NAND_SUPPORT_HAS_BEEN_FIXED */
 
 #define CONFIG_NR_DRAM_BANKS 1
 #define PHYS_SDRAM                     0x20000000

diff --git a/include/configs/delta.h b/include/configs/delta.h
index e7186e8..9c46c5b 100644 (file)
--- a/include/configs/delta.h
+++ b/include/configs/delta.h
@@ -220,8 +220,6 @@
 /*
  * NAND Flash
  */
-#undef CONFIG_NAND_LEGACY
-
 #define CONFIG_SYS_NAND0_BASE          0x0 /* 0x43100040 */ /* 0x10000000 */
 #undef CONFIG_SYS_NAND1_BASE
 
@@ -255,13 +253,6 @@
 #define CONFIG_MTD_DEBUG
 #define CONFIG_MTD_DEBUG_VERBOSE 1
 
-#define ADDR_COLUMN            1
-#define ADDR_PAGE              2
-#define ADDR_COLUMN_PAGE       3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS                1
-
 #define CONFIG_SYS_NO_FLASH            1
 
 #define CONFIG_ENV_IS_IN_NAND  1

diff --git a/include/configs/m501sk.h b/include/configs/m501sk.h
index 1e7d90e..32a8194 100644 (file)
--- a/include/configs/m501sk.h
+++ b/include/configs/m501sk.h
@@ -162,11 +162,6 @@
 #define CONFIG_SYS_PROMPT_HUSH_PS2         ">>"
 
 #define CONFIG_SYS_MAX_NAND_DEVICE     0 /* Max number of NAND devices */
-#define SECTORSIZE                          512
-
-#define ADDR_COLUMN            1
-#define ADDR_PAGE              2
-#define ADDR_COLUMN_PAGE       3
 
 #define CONFIG_NR_DRAM_BANKS   1
 #define PHYS_SDRAM             0x20000000

diff --git a/include/configs/omap2420h4.h b/include/configs/omap2420h4.h
index 1803b13..9c18842 100644 (file)
--- a/include/configs/omap2420h4.h
+++ b/include/configs/omap2420h4.h
@@ -147,42 +147,6 @@
 #define CONFIG_BOOTP_HOSTNAME
 #define CONFIG_BOOTP_BOOTPATH
 
-
-/*
- *  Board NAND Info.
- */
-#define CONFIG_NAND_LEGACY
-#define CONFIG_SYS_NAND_ADDR 0x04000000  /* physical address to access nand at CS0*/
-
-#define CONFIG_SYS_MAX_NAND_DEVICE 1   /* Max number of NAND devices */
-#define SECTORSIZE          512
-
-#define ADDR_COLUMN         1
-#define ADDR_PAGE           2
-#define ADDR_COLUMN_PAGE    3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS     1
-
-#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u16 *)0x6800A07C = d;} while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u16 *)0x6800A080 = d;} while(0)
-#define WRITE_NAND(d, adr) do {*(volatile u16 *)0x6800A084 = d;} while(0)
-#define READ_NAND(adr) (*(volatile u16 *)0x6800A084)
-#define NAND_WAIT_READY(nand)  udelay(10)
-
-#define NAND_NO_RB          1
-
-#define CONFIG_SYS_NAND_WP
-#define NAND_WP_OFF()  do {*(volatile u32 *)(0x6800A050) |= 0x00000010;} while(0)
-#define NAND_WP_ON()  do {*(volatile u32 *)(0x6800A050) &= ~0x00000010;} while(0)
-
-#define NAND_CTL_CLRALE(nandptr)
-#define NAND_CTL_SETALE(nandptr)
-#define NAND_CTL_CLRCLE(nandptr)
-#define NAND_CTL_SETCLE(nandptr)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
-
 #define CONFIG_BOOTDELAY         3
 
 #ifdef NFS_BOOT_DEFAULTS

diff --git a/include/configs/sbc2410x.h b/include/configs/sbc2410x.h
index eab9629..f3dc7fe 100644 (file)
--- a/include/configs/sbc2410x.h
+++ b/include/configs/sbc2410x.h
@@ -201,29 +201,6 @@
 #if defined(CONFIG_CMD_NAND)
 #define CONFIG_NAND_S3C2410
 #define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-
-#define NAND_WAIT_READY(nand)  NF_WaitRB()
-#define NAND_DISABLE_CE(nand)  NF_SetCE(NFCE_HIGH)
-#define NAND_ENABLE_CE(nand)   NF_SetCE(NFCE_LOW)
-#define WRITE_NAND_COMMAND(d, adr)     NF_Cmd(d)
-#define WRITE_NAND_COMMANDW(d, adr)    NF_CmdW(d)
-#define WRITE_NAND_ADDRESS(d, adr)     NF_Addr(d)
-#define WRITE_NAND(d, adr)             NF_Write(d)
-#define READ_NAND(adr)                 NF_Read()
-/* the following functions are NOP's because S3C24X0 handles this in hardware */
-#define NAND_CTL_CLRALE(nandptr)
-#define NAND_CTL_SETALE(nandptr)
-#define NAND_CTL_CLRCLE(nandptr)
-#define NAND_CTL_SETCLE(nandptr)
-/* #undef CONFIG_MTD_NAND_VERIFY_WRITE */
 #endif /* CONFIG_CMD_NAND */
 
 #define CONFIG_SETUP_MEMORY_TAGS

diff --git a/include/configs/stxxtc.h b/include/configs/stxxtc.h
index 147233d..d16262b 100644 (file)
--- a/include/configs/stxxtc.h
+++ b/include/configs/stxxtc.h
@@ -118,7 +118,6 @@
 
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
 
@@ -446,90 +445,9 @@
 #define NAND_SIZE      0x00010000      /* 64K */
 #define NAND_BASE      0xF1000000
 
-/****************************************************************/
-
-/* NAND */
-#define CONFIG_NAND_LEGACY
-#define CONFIG_SYS_NAND_BASE           NAND_BASE
-#define CONFIG_MTD_NAND_ECC_JFFS2
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_MTD_NAND_UNSAFE
-
-#define CONFIG_SYS_MAX_NAND_DEVICE     1
-#undef NAND_NO_RB
-
-#define SECTORSIZE             512
-#define ADDR_COLUMN            1
-#define ADDR_PAGE              2
-#define ADDR_COLUMN_PAGE       3
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS                1
-
-/* ALE = PC15, CLE = PB23, CE = PA7, F_RY_BY = PA6 */
-#define NAND_DISABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padat) |=  (1 << (15 - 7)); \
-       } while(0)
-
-#define NAND_ENABLE_CE(nand) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padat) &= ~(1 << (15 - 7)); \
-       } while(0)
-
-#define NAND_CTL_CLRALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat) &= ~(1 << (15 - 15)); \
-       } while(0)
-
-#define NAND_CTL_SETALE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat) |=  (1 << (15 - 15)); \
-       } while(0)
-
-#define NAND_CTL_CLRCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) &= ~(1 << (31 - 23)); \
-       } while(0)
-
-#define NAND_CTL_SETCLE(nandptr) \
-       do { \
-               (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) |=  (1 << (31 - 23)); \
-       } while(0)
-
-#ifndef NAND_NO_RB
-#define NAND_WAIT_READY(nand) \
-       do { \
-               int _tries = 0; \
-               while ((((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_padat & (1 << (15 - 6))) == 0) \
-                       if (++_tries > 100000) \
-                               break; \
-       } while (0)
-#else
-#define NAND_WAIT_READY(nand) udelay(12)
-#endif
-
-#define WRITE_NAND_COMMAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND_ADDRESS(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define WRITE_NAND(d, adr) \
-       do { \
-               *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
-       } while(0)
-
-#define READ_NAND(adr) \
-       ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr)))
-
 /*****************************************************************************/
 
 #define CONFIG_SYS_DIRECT_FLASH_TFTP
-#define CONFIG_SYS_DIRECT_NAND_TFTP
 
 /*****************************************************************************/
 

diff --git a/include/configs/svm_sc8xx.h b/include/configs/svm_sc8xx.h
index 3917a1b..425f472 100644 (file)
--- a/include/configs/svm_sc8xx.h
+++ b/include/configs/svm_sc8xx.h
@@ -147,12 +147,8 @@
 
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_DATE
 
-
-#define CONFIG_NAND_LEGACY
-
 /*
  * Miscellaneous configurable options
  */

diff --git a/include/configs/zylonite.h b/include/configs/zylonite.h
index 15c3708..0500042 100644 (file)
--- a/include/configs/zylonite.h
+++ b/include/configs/zylonite.h
@@ -193,7 +193,6 @@
 /*
  * NAND Flash
  */
-#define CONFIG_NEW_NAND_CODE
 #define CONFIG_SYS_NAND0_BASE          0x0
 #undef CONFIG_SYS_NAND1_BASE
 
@@ -227,13 +226,6 @@
 #define CONFIG_MTD_DEBUG
 #define CONFIG_MTD_DEBUG_VERBOSE 1
 
-#define ADDR_COLUMN            1
-#define ADDR_PAGE              2
-#define ADDR_COLUMN_PAGE       3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS                1
-
 #define CONFIG_SYS_NO_FLASH            1
 
 #define CONFIG_ENV_IS_IN_NAND  1