bool "Support MPC8541CDS"
select ARCH_MPC8541
-config TARGET_MPC8544DS
- bool "Support MPC8544DS"
- select ARCH_MPC8544
- imply PANIC_HANG
-
config TARGET_MPC8548CDS
bool "Support MPC8548CDS"
select ARCH_MPC8548
source "board/freescale/corenet_ds/Kconfig"
source "board/freescale/mpc8541cds/Kconfig"
-source "board/freescale/mpc8544ds/Kconfig"
source "board/freescale/mpc8548cds/Kconfig"
source "board/freescale/mpc8555cds/Kconfig"
source "board/freescale/mpc8568mds/Kconfig"
u8 res2[4];
} __attribute__ ((packed)) pixis_t;
-#elif defined(CONFIG_TARGET_MPC8544DS)
-typedef struct pixis {
- u8 id;
- u8 ver;
- u8 pver;
- u8 csr;
- u8 rst;
- u8 pwr;
- u8 aux1;
- u8 spd;
- u8 res[8];
- u8 vctl;
- u8 vstat;
- u8 vcfgen0;
- u8 vcfgen1;
- u8 vcore0;
- u8 res1;
- u8 vboot;
- u8 vspeed[2];
- u8 vclkh;
- u8 vclkl;
- u8 watch;
- u8 led;
- u8 vspeed2;
- u8 res2[34];
-} __attribute__ ((packed)) pixis_t;
-
#elif defined(CONFIG_TARGET_MPC8572DS)
typedef struct pixis {
u8 id;
+++ /dev/null
-if TARGET_MPC8544DS
-
-config SYS_BOARD
- default "mpc8544ds"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "MPC8544DS"
-
-endif
+++ /dev/null
-MPC8544DS BOARD
-M: Priyanka Jain <priyanka.jain@nxp.com>
-S: Maintained
-F: board/freescale/mpc8544ds/
-F: include/configs/MPC8544DS.h
-F: configs/MPC8544DS_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2007 Freescale Semiconductor, Inc.
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y += mpc8544ds.o
-obj-y += ddr.o
-obj-y += law.o
-obj-y += tlb.o
+++ /dev/null
-Overview
---------
-The MPC8544DS system is similar to the 85xx CDS systems such
-as the MPC8548CDS due to the similar E500 core. However, it
-is placed on the same board as the 8641 HPCN system.
-
-
-Flash Banks
------------
-Like the 85xx CDS systems, the 8544 DS board has two flash banks.
-They are both present on boot, but there locations can be swapped
-using the dip-switch SW10, bit 2.
-
-However, unlike the CDS systems, but similar to the 8641 HPCN
-board, a runtime reset through the FPGA can also affect a swap
-on the flash bank mappings for the next reset cycle.
-
-Irrespective of the switch SW10[2], booting is always from the
-boot bank at 0xfff8_0000.
-
-
-Memory Map
-----------
-
-0xff80_0000 - 0xffbf_ffff Alternate bank 4MB
-0xffc0_0000 - 0xffff_ffff Boot bank 4MB
-
-0xffb8_0000 Alternate image start 512KB
-0xfff8_0000 Boot image start 512KB
-
-
-Flashing Images
----------------
-
-For example, to place a new image in the alternate flash bank
-and then reset with that new image temporarily, use this:
-
- tftp 1000000 u-boot.bin.8544ds
- erase ffb80000 ffbfffff
- cp.b 1000000 ffb80000 80000
- pixis_reset altbank
-
-
-To overwrite the image in the boot flash bank:
-
- tftp 1000000 u-boot.bin.8544ds
- protect off all
- erase fff80000 ffffffff
- cp.b 1000000 fff80000 80000
-
-Other example U-Boot image and flash manipulations examples
-can be found in the README.mpc85xxcds file as well.
-
-
-The pixis_reset command
------------------------
-A new command, "pixis_reset", is introduced to reset mpc8641hpcn board
-using the FPGA sequencer. When the board restarts, it has the option
-of using either the current or alternate flash bank as the boot
-image, with or without the watchdog timer enabled, and finally with
-or without frequency changes.
-
-Usage is;
-
- pixis_reset
- pixis_reset altbank
- pixis_reset altbank wd
- pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
- pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
-
-Examples;
-
- /* reset to current bank, like "reset" command */
- pixis_reset
-
- /* reset board but use the to alternate flash bank */
- pixis_reset altbank
-
- /* reset board, use alternate flash bank with watchdog timer enabled*/
- pixis_reset altbank wd
-
- /* reset board to alternate bank with frequency changed.
- * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio
- */
- pixis-reset altbank cf 40 2.5 10
-
-Valid clock choices are in the 8641 Reference Manuals.
-
-
-Using the Device Tree Source File
----------------------------------
-To create the DTB (Device Tree Binary) image file,
-use a command similar to this:
-
- dtc -b 0 -f -I dts -O dtb mpc8544ds.dts > mpc8544ds.dtb
-
-Likely, that .dts file will come from here;
-
- linux-2.6/arch/powerpc/boot/dts/mpc8544ds.dts
-
-After placing the DTB file in your TFTP disk area,
-you can download that dtb file using a command like:
-
- tftp 900000 mpc8544ds.dtb
-
-Burn it to flash if you want.
-
-
-Booting Linux
--------------
-
-Place a linux uImage in the TFTP disk area too.
-
- tftp 1000000 uImage.8544
- tftp 900000 mpc8544ds.dtb
- bootm 1000000 - 900000
-
-Watch your ethact, netdev and bootargs U-Boot environment variables.
-You may want to do something like this too:
-
- setenv ethact eTSEC3
- setenv netdev eth1
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- /*
- * Factors to consider for clock adjust:
- * - number of chips on bus
- * - position of slot
- * - DDR1 vs. DDR2?
- * - ???
- *
- * This needs to be determined on a board-by-board basis.
- * 0110 3/4 cycle late
- * 0111 7/8 cycle late
- */
- popts->clk_adjust = 7;
-
- /*
- * Factors to consider for CPO:
- * - frequency
- * - ddr1 vs. ddr2
- */
- popts->cpo_override = 10;
-
- /*
- * Factors to consider for write data delay:
- * - number of DIMMs
- *
- * 1 = 1/4 clock delay
- * 2 = 1/2 clock delay
- * 3 = 3/4 clock delay
- * 4 = 1 clock delay
- * 5 = 5/4 clock delay
- * 6 = 3/2 clock delay
- */
- popts->write_data_delay = 3;
-
- /* 2T timing enable */
- popts->twot_en = 1;
-
- /*
- * Factors to consider for half-strength driver enable:
- * - number of DIMMs installed
- */
- popts->half_strength_driver_enable = 0;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008, 2010 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
- SET_LAW(CONFIG_SYS_LBC_NONCACHE_BASE, LAW_SIZE_128M, LAW_TRGT_IF_LBC),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2007,2009-2010 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <net.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_pci.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/fsl_serdes.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <fsl_mdio.h>
-#include <tsec.h>
-#include <netdev.h>
-
-#include "../common/sgmii_riser.h"
-
-int checkboard (void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
- volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
- u8 vboot;
- u8 *pixis_base = (u8 *)PIXIS_BASE;
-
- if ((uint)&gur->porpllsr != 0xe00e0000) {
- printf("immap size error %lx\n",(ulong)&gur->porpllsr);
- }
- printf ("Board: MPC8544DS, Sys ID: 0x%02x, "
- "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
- in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
- in_8(pixis_base + PIXIS_PVER));
-
- vboot = in_8(pixis_base + PIXIS_VBOOT);
- if (vboot & PIXIS_VBOOT_FMAP)
- printf ("vBank: %d\n", ((vboot & PIXIS_VBOOT_FBANK) >> 6));
- else
- puts ("Promjet\n");
-
- lbc->ltesr = 0xffffffff; /* Clear LBC error interrupts */
- lbc->lteir = 0xffffffff; /* Enable LBC error interrupts */
- ecm->eedr = 0xffffffff; /* Clear ecm errors */
- ecm->eeer = 0xffffffff; /* Enable ecm errors */
-
- return 0;
-}
-
-#ifdef CONFIG_PCI1
-static struct pci_controller pci1_hose;
-#endif
-
-#ifdef CONFIG_PCIE3
-static struct pci_controller pcie3_hose;
-#endif
-
-void pci_init_board(void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- struct fsl_pci_info pci_info;
- u32 devdisr, pordevsr, io_sel;
- u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel;
- int first_free_busno = 0;
-
- int pcie_ep, pcie_configured;
-
- devdisr = in_be32(&gur->devdisr);
- pordevsr = in_be32(&gur->pordevsr);
- porpllsr = in_be32(&gur->porpllsr);
- io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
-
- debug (" pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel);
-
- puts("\n");
-
-#ifdef CONFIG_PCIE3
- pcie_configured = is_serdes_configured(PCIE3);
-
- if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE3)){
- /* contains both PCIE3 MEM & IO space */
- set_next_law(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_4M,
- LAW_TRGT_IF_PCIE_3);
- SET_STD_PCIE_INFO(pci_info, 3);
- pcie_ep = fsl_setup_hose(&pcie3_hose, pci_info.regs);
-
- /* outbound memory */
- pci_set_region(&pcie3_hose.regions[0],
- CONFIG_SYS_PCIE3_MEM_BUS2,
- CONFIG_SYS_PCIE3_MEM_PHYS2,
- CONFIG_SYS_PCIE3_MEM_SIZE2,
- PCI_REGION_MEM);
-
- pcie3_hose.region_count = 1;
-
- printf("PCIE3: connected to ULI as %s (base addr %lx)\n",
- pcie_ep ? "Endpoint" : "Root Complex",
- pci_info.regs);
- first_free_busno = fsl_pci_init_port(&pci_info,
- &pcie3_hose, first_free_busno);
-
- /*
- * Activate ULI1575 legacy chip by performing a fake
- * memory access. Needed to make ULI RTC work.
- */
- in_be32((u32 *)CONFIG_SYS_PCIE3_MEM_BUS);
- } else {
- printf("PCIE3: disabled\n");
- }
- puts("\n");
-#else
- setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE3); /* disable */
-#endif
-
-#ifdef CONFIG_PCIE1
- SET_STD_PCIE_INFO(pci_info, 1);
- first_free_busno = fsl_pcie_init_ctrl(first_free_busno, devdisr, PCIE1, &pci_info);
-#else
- setbits_be32(&gur->devdisr, _DEVDISR_PCIE1); /* disable */
-#endif
-
-#ifdef CONFIG_PCIE2
- SET_STD_PCIE_INFO(pci_info, 2);
- first_free_busno = fsl_pcie_init_ctrl(first_free_busno, devdisr, PCIE2, &pci_info);
-#else
- setbits_be32(&gur->devdisr, _DEVDISR_PCIE2); /* disable */
-#endif
-
-#ifdef CONFIG_PCI1
- pci_speed = 66666000;
- pci_32 = 1;
- pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;
- pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;
-
- if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
- SET_STD_PCI_INFO(pci_info, 1);
- set_next_law(pci_info.mem_phys,
- law_size_bits(pci_info.mem_size), pci_info.law);
- set_next_law(pci_info.io_phys,
- law_size_bits(pci_info.io_size), pci_info.law);
-
- pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs);
- printf("PCI: %d bit, %s MHz, %s, %s, %s (base address %lx)\n",
- (pci_32) ? 32 : 64,
- (pci_speed == 33333000) ? "33" :
- (pci_speed == 66666000) ? "66" : "unknown",
- pci_clk_sel ? "sync" : "async",
- pci_agent ? "agent" : "host",
- pci_arb ? "arbiter" : "external-arbiter",
- pci_info.regs);
-
- first_free_busno = fsl_pci_init_port(&pci_info,
- &pci1_hose, first_free_busno);
- } else {
- printf("PCI: disabled\n");
- }
-
- puts("\n");
-#else
- setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */
-#endif
-}
-
-int last_stage_init(void)
-{
- return 0;
-}
-
-
-unsigned long
-get_board_sys_clk(ulong dummy)
-{
- u8 i, go_bit, rd_clks;
- ulong val = 0;
- u8 *pixis_base = (u8 *)PIXIS_BASE;
-
- go_bit = in_8(pixis_base + PIXIS_VCTL);
- go_bit &= 0x01;
-
- rd_clks = in_8(pixis_base + PIXIS_VCFGEN0);
- rd_clks &= 0x1C;
-
- /*
- * Only if both go bit and the SCLK bit in VCFGEN0 are set
- * should we be using the AUX register. Remember, we also set the
- * GO bit to boot from the alternate bank on the on-board flash
- */
-
- if (go_bit) {
- if (rd_clks == 0x1c)
- i = in_8(pixis_base + PIXIS_AUX);
- else
- i = in_8(pixis_base + PIXIS_SPD);
- } else {
- i = in_8(pixis_base + PIXIS_SPD);
- }
-
- i &= 0x07;
-
- switch (i) {
- case 0:
- val = 33333333;
- break;
- case 1:
- val = 40000000;
- break;
- case 2:
- val = 50000000;
- break;
- case 3:
- val = 66666666;
- break;
- case 4:
- val = 83000000;
- break;
- case 5:
- val = 100000000;
- break;
- case 6:
- val = 133333333;
- break;
- case 7:
- val = 166666666;
- break;
- }
-
- return val;
-}
-
-
-#define MIIM_CIS8204_SLED_CON 0x1b
-#define MIIM_CIS8204_SLEDCON_INIT 0x1115
-/*
- * Hack to write all 4 PHYs with the LED values
- */
-int board_phy_config(struct phy_device *phydev)
-{
- static int do_once;
- uint phyid;
- struct mii_dev *bus = phydev->bus;
-
- if (phydev->drv->config)
- phydev->drv->config(phydev);
- if (do_once)
- return 0;
-
- for (phyid = 0; phyid < 4; phyid++)
- bus->write(bus, phyid, MDIO_DEVAD_NONE, MIIM_CIS8204_SLED_CON,
- MIIM_CIS8204_SLEDCON_INIT);
-
- do_once = 1;
-
- return 0;
-}
-
-
-int board_eth_init(struct bd_info *bis)
-{
-#ifdef CONFIG_TSEC_ENET
- struct fsl_pq_mdio_info mdio_info;
- struct tsec_info_struct tsec_info[2];
- int num = 0;
-
-#ifdef CONFIG_TSEC1
- SET_STD_TSEC_INFO(tsec_info[num], 1);
- if (is_serdes_configured(SGMII_TSEC1)) {
- puts("eTSEC1 is in sgmii mode.\n");
- tsec_info[num].flags |= TSEC_SGMII;
- }
- num++;
-#endif
-#ifdef CONFIG_TSEC3
- SET_STD_TSEC_INFO(tsec_info[num], 3);
- if (is_serdes_configured(SGMII_TSEC3)) {
- puts("eTSEC3 is in sgmii mode.\n");
- tsec_info[num].flags |= TSEC_SGMII;
- }
- num++;
-#endif
-
- if (!num) {
- printf("No TSECs initialized\n");
-
- return 0;
- }
-
- if (is_serdes_configured(SGMII_TSEC1) ||
- is_serdes_configured(SGMII_TSEC3)) {
- fsl_sgmii_riser_init(tsec_info, num);
- }
-
- mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
- mdio_info.name = DEFAULT_MII_NAME;
- fsl_pq_mdio_init(bis, &mdio_info);
-
- tsec_eth_init(bis, tsec_info, num);
-#endif
- return pci_eth_init(bis);
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
- ft_cpu_setup(blob, bd);
-
- FT_FSL_PCI_SETUP;
-
-#ifdef CONFIG_FSL_SGMII_RISER
- fsl_sgmii_riser_fdt_fixup(blob);
-#endif
-
- return 0;
-}
-#endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- MAS3_SX|MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- /*
- * TLB 0: 64M Non-cacheable, guarded
- * 0xfc000000 64M Covers FLASH at 0xFE800000 and 0xFF800000
- * Out of reset this entry is only 4K.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_BOOT_BLOCK, CONFIG_SYS_BOOT_BLOCK,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_64M, 1),
- /*
- * TLB 1: 1G Non-cacheable, guarded
- * 0x80000000 1G PCIE 8,9,a,b
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE_VIRT, CONFIG_SYS_PCIE_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1G, 1),
-
- /*
- * TLB 2: 256M Non-cacheable, guarded
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCI_VIRT, CONFIG_SYS_PCI_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_256M, 1),
-
- /*
- * TLB 3: 256M Non-cacheable, guarded
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCI_VIRT + 0x10000000, CONFIG_SYS_PCI_PHYS + 0x10000000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_256M, 1),
-
- /*
- * TLB 4: 64M Non-cacheable, guarded
- * 0xe000_0000 1M CCSRBAR
- * 0xe100_0000 255M PCI IO range
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_64M, 1),
-
- /*
- * TLB 5: 64M Non-cacheable, guarded
- * 0xf8000000 64M PIXIS 0xF8000000 - 0xFBFFFFFF
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_LBC_NONCACHE_BASE, CONFIG_SYS_LBC_NONCACHE_BASE,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_64M, 1),
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFFF80000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_MPC85xx=y
-# CONFIG_CMD_ERRATA is not set
-CONFIG_TARGET_MPC8544DS=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=10
-# CONFIG_CONSOLE_MUX is not set
-# CONFIG_MISC_INIT_R is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_REGINFO=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-# CONFIG_CMD_HASH is not set
-CONFIG_CMD_EXT2=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_ENV_ADDR=0xFFF70000
-CONFIG_SCSI_AHCI=y
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_RTL8139=y
-CONFIG_TSEC_ENET=y
-CONFIG_SCSI=y
-CONFIG_SYS_NS16550=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_PCI=y
-CONFIG_USB_STORAGE=y
-CONFIG_VIDEO=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc.
- */
-
-/*
- * mpc8544ds board configuration file
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_PCI1 1 /* PCI controller 1 */
-#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */
-#define CONFIG_PCIE3 1 /* PCIE controller 3 (ULI bridge) */
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-
-#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
-
-#ifndef __ASSEMBLY__
-#include <linux/stringify.h>
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-#endif
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-
-/*
- * Only possible on E500 Version 2 or newer cores.
- */
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#define CONFIG_SYS_CCSRBAR 0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
-
-/* Make sure required options are set */
-#ifndef CONFIG_SPD_EEPROM
-#error ("CONFIG_SPD_EEPROM is required")
-#endif
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
- *
- * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
- *
- * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
- *
- * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable
- * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
- *
- * Localbus cacheable
- *
- * 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable
- * 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0
- *
- * Localbus non-cacheable
- *
- * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable
- * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable
- * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable
- *
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* boot TLB */
-
-#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */
-
-#define CONFIG_SYS_BR0_PRELIM 0xff801001
-#define CONFIG_SYS_BR1_PRELIM 0xfe801001
-
-#define CONFIG_SYS_OR0_PRELIM 0xff806e65
-#define CONFIG_SYS_OR1_PRELIM 0xff806e65
-
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_LBC_NONCACHE_BASE 0xf8000000
-
-#define CONFIG_SYS_BR2_PRELIM 0xf8201001 /* port size 16bit */
-#define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/
-
-#define CONFIG_SYS_BR3_PRELIM 0xf8100801 /* port size 8bit */
-#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
-
-#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
-#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
-#define PIXIS_ID 0x0 /* Board ID at offset 0 */
-#define PIXIS_VER 0x1 /* Board version at offset 1 */
-#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
-#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
-#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch
- * register */
-#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
-#define PIXIS_VCTL 0x10 /* VELA Control Register */
-#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
-#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
-#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
-#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */
-#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */
-#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
-#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
-#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
-#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
-#define PIXIS_VSPEED2 0x1d /* VELA VSpeed 2 */
-#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
-#define PIXIS_VSPEED2_TSEC1SER 0x2
-#define PIXIS_VSPEED2_TSEC3SER 0x1
-#define PIXIS_VCFGEN1_TSEC1SER 0x20
-#define PIXIS_VCFGEN1_TSEC3SER 0x40
-#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER)
-#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER)
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-#define CONFIG_SYS_PCIE_VIRT 0x80000000 /* 1G PCIE TLB */
-#define CONFIG_SYS_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */
-#define CONFIG_SYS_PCI_VIRT 0xc0000000 /* 512M PCI TLB */
-#define CONFIG_SYS_PCI_PHYS 0xc0000000 /* 512M PCI TLB */
-
-#define CONFIG_SYS_PCI1_MEM_VIRT 0xc0000000
-#define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000
-#define CONFIG_SYS_PCI1_MEM_PHYS 0xc0000000
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000
-#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 2, Slot 1, tgtid 1, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME "Slot 1"
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE2_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0x80000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xe1010000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xe1010000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 1, Slot 2,tgtid 2, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME "Slot 2"
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xe1020000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xe1020000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 3, direct to uli, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_NAME "ULI"
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x00100000 /* 1M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xb0100000 /* reuse mem LAW */
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00100000 /* 1M */
-#define CONFIG_SYS_PCIE3_MEM_VIRT2 0xb0200000
-#define CONFIG_SYS_PCIE3_MEM_BUS2 0xb0200000
-#define CONFIG_SYS_PCIE3_MEM_PHYS2 0xb0200000
-#define CONFIG_SYS_PCIE3_MEM_SIZE2 0x00200000 /* 1M */
-
-#if defined(CONFIG_PCI)
-
-/*PCIE video card used*/
-#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT
-
-/*PCI video card used*/
-/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/
-
-/* video */
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_BIOSEMU
-#define CONFIG_ATI_RADEON_FB
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
-#endif
-
-
-#ifndef CONFIG_PCI_PNP
- #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS
- #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS
- #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-
-#ifdef CONFIG_SCSI_AHCI
-#define CONFIG_SATA_ULI5288
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#endif /* CONFIG_SCSI_AHCI */
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-
-#define CONFIG_PIXIS_SGMII_CMD
-#define CONFIG_FSL_SGMII_RISER 1
-#define SGMII_RISER_PHY_OFFSET 0x1c
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC3_PHY_ADDR 1
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC3_PHYIDX 0
-
-#define CONFIG_ETHPRIME "eTSEC1"
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * USB
- */
-
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_PCI_EHCI_DEVICE 0
-#endif
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_IPADDR 192.168.1.251
-
-#define CONFIG_HOSTNAME "8544ds_unknown"
-#define CONFIG_ROOTPATH "/nfs/mpc85xx"
-#define CONFIG_BOOTFILE "8544ds/uImage.uboot"
-#define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */
-
-#define CONFIG_SERVERIP 192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK 255.255.0.0
-
-#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-"netdev=eth0\0" \
-"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
-"tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize; " \
- "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize\0" \
-"consoledev=ttyS0\0" \
-"ramdiskaddr=2000000\0" \
-"ramdiskfile=8544ds/ramdisk.uboot\0" \
-"fdtaddr=1e00000\0" \
-"fdtfile=8544ds/mpc8544ds.dtb\0" \
-"bdev=sda3\0"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / commitdiff