include/configs/xpedite550x.h

   1 /*
   2  * Copyright 2010 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * xpedite550x board configuration file
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_XPEDITE550X      1
  18 #define CONFIG_SYS_BOARD_NAME   "XPedite5500"
  19 #define CONFIG_SYS_FORM_PMC_XMC 1
  20 #define CONFIG_PRPMC_PCI_ALIAS  "pci0"  /* Processor PMC interface on pci0 */
  21 #define CONFIG_BOARD_EARLY_INIT_R       /* Call board_pre_init */
  22
  23 #ifndef CONFIG_SYS_TEXT_BASE
  24 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  25 #endif
  26
  27 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  28 #define CONFIG_PCIE1            1       /* PCIE controller 1 (PEX8112 or XMC) */
  29 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  30 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  31 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  32 #define CONFIG_FSL_PCIE_RESET   1       /* need PCIe reset errata */
  33
  34 /*
  35  * Multicore config
  36  */
  37 #define CONFIG_MP
  38 #define CONFIG_BPTR_VIRT_ADDR   0xee000000      /* virt boot page address */
  39 #define CONFIG_MPC8xxx_DISABLE_BPTR             /* Don't leave BPTR enabled */
  40
  41 /*
  42  * DDR config
  43  */
  44 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  45 #define CONFIG_DDR_SPD
  46 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  47 #define SPD_EEPROM_ADDRESS                      0x54
  48 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  49 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  50 #define CONFIG_CHIP_SELECTS_PER_CTRL 2
  51 #define CONFIG_DDR_ECC
  52 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  53 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000 /* DDR is system memory*/
  54 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  55 #define CONFIG_VERY_BIG_RAM
  56
  57 #ifndef __ASSEMBLY__
  58 extern unsigned long get_board_sys_clk(unsigned long dummy);
  59 extern unsigned long get_board_ddr_clk(unsigned long dummy);
  60 #endif
  61
  62 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC85xx */
  63 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk(0) /* ddrclk for MPC85xx */
  64
  65 /*
  66  * These can be toggled for performance analysis, otherwise use default.
  67  */
  68 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  69 #define CONFIG_BTB                      /* toggle branch predition */
  70 #define CONFIG_ENABLE_36BIT_PHYS        1
  71
  72 #define CONFIG_SYS_CCSRBAR              0xef000000
  73 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  74
  75 /*
  76  * Diagnostics
  77  */
  78 #define CONFIG_SYS_ALT_MEMTEST
  79 #define CONFIG_SYS_MEMTEST_START        0x10000000
  80 #define CONFIG_SYS_MEMTEST_END          0x20000000
  81 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY | \
  82                                          CONFIG_SYS_POST_I2C)
  83 #define I2C_ADDR_LIST                   {CONFIG_SYS_I2C_EEPROM_ADDR,    \
  84                                          CONFIG_SYS_I2C_LM75_ADDR,      \
  85                                          CONFIG_SYS_I2C_LM90_ADDR,      \
  86                                          CONFIG_SYS_I2C_PCA953X_ADDR0,  \
  87                                          CONFIG_SYS_I2C_PCA953X_ADDR2,  \
  88                                          CONFIG_SYS_I2C_PCA953X_ADDR3,  \
  89                                          CONFIG_SYS_I2C_RTC_ADDR}
  90
  91 /*
  92  * Memory map
  93  * 0x0000_0000 0x7fff_ffff      DDR                     2G Cacheable
  94  * 0x8000_0000 0xbfff_ffff      PCIe1 Mem               1G non-cacheable
  95  * 0xe000_0000 0xe7ff_ffff      SRAM/SSRAM/L1 Cache     128M non-cacheable
  96  * 0xe800_0000 0xe87f_ffff      PCIe1 IO                8M non-cacheable
  97  * 0xee00_0000 0xee00_ffff      Boot page translation   4K non-cacheable
  98  * 0xef00_0000 0xef0f_ffff      CCSR/IMMR               1M non-cacheable
  99  * 0xef80_0000 0xef8f_ffff      NAND Flash              1M non-cacheable
 100  * 0xf000_0000 0xf7ff_ffff      NOR Flash 2             128M non-cacheable
 101  * 0xf800_0000 0xffff_ffff      NOR Flash 1             128M non-cacheable
 102  */
 103
 104 #define CONFIG_SYS_LBC_LCRR     (LCRR_CLKDIV_8 | LCRR_EADC_3)
 105
 106 /*
 107  * NAND flash configuration
 108  */
 109 #define CONFIG_SYS_NAND_BASE            0xef800000
 110 #define CONFIG_SYS_NAND_BASE2           0xef840000 /* Unused at this time */
 111 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, \
 112                                          CONFIG_SYS_NAND_BASE2}
 113 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 114 #define CONFIG_NAND_FSL_ELBC
 115
 116 /*
 117  * NOR flash configuration
 118  */
 119 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 120 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 121 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 122 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 123 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 124 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 125 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 126 #define CONFIG_FLASH_CFI_DRIVER
 127 #define CONFIG_SYS_FLASH_CFI
 128 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 129 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff40000, 0xc0000}, \
 130                                                   {0xf7f40000, 0xc0000} }
 131 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 132
 133 /*
 134  * Chip select configuration
 135  */
 136 /* NOR Flash 0 on CS0 */
 137 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  | \
 138                                  BR_PS_16               | \
 139                                  BR_V)
 140 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            | \
 141                                  OR_GPCM_CSNT           | \
 142                                  OR_GPCM_XACS           | \
 143                                  OR_GPCM_ACS_DIV2       | \
 144                                  OR_GPCM_SCY_8          | \
 145                                  OR_GPCM_TRLX           | \
 146                                  OR_GPCM_EHTR           | \
 147                                  OR_GPCM_EAD)
 148
 149 /* NOR Flash 1 on CS1 */
 150 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 | \
 151                                  BR_PS_16               | \
 152                                  BR_V)
 153 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 154
 155 /* NAND flash on CS2 */
 156 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   | \
 157                                  (2<<BR_DECC_SHIFT)     | \
 158                                  BR_PS_8                | \
 159                                  BR_MS_FCM              | \
 160                                  BR_V)
 161
 162 /* NAND flash on CS2 */
 163 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB    | \
 164                                  OR_FCM_PGS     | \
 165                                  OR_FCM_CSCT    | \
 166                                  OR_FCM_CST     | \
 167                                  OR_FCM_CHT     | \
 168                                  OR_FCM_SCY_1   | \
 169                                  OR_FCM_TRLX    | \
 170                                  OR_FCM_EHTR)
 171
 172 /* NAND flash on CS3 */
 173 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  | \
 174                                  (2<<BR_DECC_SHIFT)     | \
 175                                  BR_PS_8                | \
 176                                  BR_MS_FCM              | \
 177                                  BR_V)
 178 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 179
 180 /*
 181  * Use L1 as initial stack
 182  */
 183 #define CONFIG_SYS_INIT_RAM_LOCK        1
 184 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 185 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 186
 187 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 188 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 189
 190 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 191 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 192
 193 /*
 194  * Serial Port
 195  */
 196 #define CONFIG_CONS_INDEX               1
 197 #define CONFIG_SYS_NS16550_SERIAL
 198 #define CONFIG_SYS_NS16550_REG_SIZE     1
 199 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 200 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 201 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 202 #define CONFIG_SYS_BAUDRATE_TABLE       \
 203         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 204 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 205 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 206
 207 #define CONFIG_FDT_FIXUP_PCI_IRQ        1
 208
 209 /*
 210  * I2C
 211  */
 212 #define CONFIG_SYS_I2C
 213 #define CONFIG_SYS_I2C_FSL
 214 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 215 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 216 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 217 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 218 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 219 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 220
 221 /* I2C DS7505 temperature sensor */
 222 #define CONFIG_SYS_I2C_LM75_ADDR        0x48
 223
 224 /* I2C ADT7461 temperature sensor */
 225 #define CONFIG_SYS_I2C_LM90_ADDR        0x4C
 226
 227 /* I2C EEPROM - AT24C128B */
 228 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 229 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 230 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 231 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 232
 233 /* I2C RTC */
 234 #define CONFIG_RTC_M41T11               1
 235 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 236 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 237
 238 /* GPIO */
 239 #define CONFIG_PCA953X
 240 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 241 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 242 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 243 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 244 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 245
 246 /*
 247  * GPIO pin definitions, PU = pulled high, PD = pulled low
 248  */
 249 /* PCA9557 @ 0x18*/
 250 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 251 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
 252 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 253 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
 254 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 255 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Write protection (0: disabled, 1: enabled) */
 256
 257 /* PCA9557 @ 0x1e*/
 258 #define CONFIG_SYS_PCA953X_XMC_GA0              0x01 /* PU; */
 259 #define CONFIG_SYS_PCA953X_XMC_GA1              0x02 /* PU; */
 260 #define CONFIG_SYS_PCA953X_XMC_GA2              0x04 /* PU; */
 261 #define CONFIG_SYS_PCA953X_XMC_WAKE             0x10 /* PU; */
 262 #define CONFIG_SYS_PCA953X_XMC_BIST             0x20 /* Enable XMC BIST */
 263 #define CONFIG_SYS_PCA953X_PMC_EREADY           0x40 /* PU; PMC PCI eready */
 264 #define CONFIG_SYS_PCA953X_PMC_MONARCH          0x80 /* PMC monarch mode enable */
 265
 266 /* PCA9557 @ 0x1f */
 267 #define CONFIG_SYS_PCA953X_MC_GPIO0             0x01 /* PU; */
 268 #define CONFIG_SYS_PCA953X_MC_GPIO1             0x02 /* PU; */
 269 #define CONFIG_SYS_PCA953X_MC_GPIO2             0x04 /* PU; */
 270 #define CONFIG_SYS_PCA953X_MC_GPIO3             0x08 /* PU; */
 271 #define CONFIG_SYS_PCA953X_MC_GPIO4             0x10 /* PU; */
 272 #define CONFIG_SYS_PCA953X_MC_GPIO5             0x20 /* PU; */
 273 #define CONFIG_SYS_PCA953X_MC_GPIO6             0x40 /* PU; */
 274 #define CONFIG_SYS_PCA953X_MC_GPIO7             0x80 /* PU; */
 275
 276 /*
 277  * General PCI
 278  * Memory space is mapped 1-1, but I/O space must start from 0.
 279  */
 280
 281 /* controller 1 - PEX8112 or XMC, depending on build option */
 282 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 283 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 284 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 285 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 286 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 287 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 288
 289 /*
 290  * Networking options
 291  */
 292 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
 293 #define CONFIG_TSEC_TBI
 294 #define CONFIG_MII              1       /* MII PHY management */
 295 #define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
 296 #define CONFIG_ETHPRIME         "eTSEC2"
 297
 298 /*
 299  * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
 300  * 1000mbps SGMII link
 301  */
 302 #define CONFIG_TSEC_TBICR_SETTINGS ( \
 303                 TBICR_PHY_RESET \
 304                 | TBICR_FULL_DUPLEX \
 305                 | TBICR_SPEED1_SET \
 306                 )
 307
 308 #define CONFIG_TSEC1            1
 309 #define CONFIG_TSEC1_NAME       "eTSEC1"
 310 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 311 #define TSEC1_PHY_ADDR          1
 312 #define TSEC1_PHYIDX            0
 313 #define CONFIG_HAS_ETH0
 314
 315 #define CONFIG_TSEC2            1
 316 #define CONFIG_TSEC2_NAME       "eTSEC2"
 317 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 318 #define TSEC2_PHY_ADDR          2
 319 #define TSEC2_PHYIDX            0
 320 #define CONFIG_HAS_ETH1
 321
 322 #define CONFIG_TSEC3            1
 323 #define CONFIG_TSEC3_NAME       "eTSEC3"
 324 #define TSEC3_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 325 #define TSEC3_PHY_ADDR          3
 326 #define TSEC3_PHYIDX            0
 327 #define CONFIG_HAS_ETH2
 328
 329 /*
 330  * USB
 331  */
 332 #define CONFIG_USB_EHCI_FSL
 333 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 334
 335 /*
 336  * Miscellaneous configurable options
 337  */
 338 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 339 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 340 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 341 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 342 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 343 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 344 #define CONFIG_CMDLINE_EDITING  1               /* add command line history     */
 345 #define CONFIG_AUTO_COMPLETE    1               /* add autocompletion support */
 346 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 347 #define CONFIG_PANIC_HANG                       /* do not reset board on panic */
 348 #define CONFIG_PREBOOT                          /* enable preboot variable */
 349 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 350
 351 /*
 352  * For booting Linux, the board info and command line data
 353  * have to be in the first 16 MB of memory, since this is
 354  * the maximum mapped by the Linux kernel during initialization.
 355  */
 356 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 357 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 358
 359 /*
 360  * Environment Configuration
 361  */
 362 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 363 #define CONFIG_ENV_SIZE         0x8000
 364 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
 365
 366 /*
 367  * Flash memory map:
 368  * fff80000 - ffffffff     Pri U-Boot (512 KB)
 369  * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
 370  * fff00000 - fff3ffff     Pri FDT (256KB)
 371  * fef00000 - ffefffff     Pri OS image (16MB)
 372  * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
 373  *
 374  * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
 375  * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
 376  * f7f00000 - f7f3ffff     Sec FDT (256KB)
 377  * f6f00000 - f7efffff     Sec OS image (16MB)
 378  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
 379  */
 380 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff80000)
 381 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f80000)
 382 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfff00000)
 383 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7f00000)
 384 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 385 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 386
 387 #define CONFIG_PROG_UBOOT1                                              \
 388         "$download_cmd $loadaddr $ubootfile; "                          \
 389         "if test $? -eq 0; then "                                       \
 390                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 391                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 392                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 393                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 394                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 395                 "if test $? -ne 0; then "                               \
 396                         "echo PROGRAM FAILED; "                         \
 397                 "else; "                                                \
 398                         "echo PROGRAM SUCCEEDED; "                      \
 399                 "fi; "                                                  \
 400         "else; "                                                        \
 401                 "echo DOWNLOAD FAILED; "                                \
 402         "fi;"
 403
 404 #define CONFIG_PROG_UBOOT2                                              \
 405         "$download_cmd $loadaddr $ubootfile; "                          \
 406         "if test $? -eq 0; then "                                       \
 407                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 408                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 409                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 410                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 411                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 412                 "if test $? -ne 0; then "                               \
 413                         "echo PROGRAM FAILED; "                         \
 414                 "else; "                                                \
 415                         "echo PROGRAM SUCCEEDED; "                      \
 416                 "fi; "                                                  \
 417         "else; "                                                        \
 418                 "echo DOWNLOAD FAILED; "                                \
 419         "fi;"
 420
 421 #define CONFIG_BOOT_OS_NET                                              \
 422         "$download_cmd $osaddr $osfile; "                               \
 423         "if test $? -eq 0; then "                                       \
 424                 "if test -n $fdtaddr; then "                            \
 425                         "$download_cmd $fdtaddr $fdtfile; "             \
 426                         "if test $? -eq 0; then "                       \
 427                                 "bootm $osaddr - $fdtaddr; "            \
 428                         "else; "                                        \
 429                                 "echo FDT DOWNLOAD FAILED; "            \
 430                         "fi; "                                          \
 431                 "else; "                                                \
 432                         "bootm $osaddr; "                               \
 433                 "fi; "                                                  \
 434         "else; "                                                        \
 435                 "echo OS DOWNLOAD FAILED; "                             \
 436         "fi;"
 437
 438 #define CONFIG_PROG_OS1                                                 \
 439         "$download_cmd $osaddr $osfile; "                               \
 440         "if test $? -eq 0; then "                                       \
 441                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 442                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 443                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 444                 "if test $? -ne 0; then "                               \
 445                         "echo OS PROGRAM FAILED; "                      \
 446                 "else; "                                                \
 447                         "echo OS PROGRAM SUCCEEDED; "                   \
 448                 "fi; "                                                  \
 449         "else; "                                                        \
 450                 "echo OS DOWNLOAD FAILED; "                             \
 451         "fi;"
 452
 453 #define CONFIG_PROG_OS2                                                 \
 454         "$download_cmd $osaddr $osfile; "                               \
 455         "if test $? -eq 0; then "                                       \
 456                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 457                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 458                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 459                 "if test $? -ne 0; then "                               \
 460                         "echo OS PROGRAM FAILED; "                      \
 461                 "else; "                                                \
 462                         "echo OS PROGRAM SUCCEEDED; "                   \
 463                 "fi; "                                                  \
 464         "else; "                                                        \
 465                 "echo OS DOWNLOAD FAILED; "                             \
 466         "fi;"
 467
 468 #define CONFIG_PROG_FDT1                                                \
 469         "$download_cmd $fdtaddr $fdtfile; "                             \
 470         "if test $? -eq 0; then "                                       \
 471                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 472                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 473                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 474                 "if test $? -ne 0; then "                               \
 475                         "echo FDT PROGRAM FAILED; "                     \
 476                 "else; "                                                \
 477                         "echo FDT PROGRAM SUCCEEDED; "                  \
 478                 "fi; "                                                  \
 479         "else; "                                                        \
 480                 "echo FDT DOWNLOAD FAILED; "                            \
 481         "fi;"
 482
 483 #define CONFIG_PROG_FDT2                                                \
 484         "$download_cmd $fdtaddr $fdtfile; "                             \
 485         "if test $? -eq 0; then "                                       \
 486                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 487                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 488                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 489                 "if test $? -ne 0; then "                               \
 490                         "echo FDT PROGRAM FAILED; "                     \
 491                 "else; "                                                \
 492                         "echo FDT PROGRAM SUCCEEDED; "                  \
 493                 "fi; "                                                  \
 494         "else; "                                                        \
 495                 "echo FDT DOWNLOAD FAILED; "                            \
 496         "fi;"
 497
 498 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 499         "autoload=yes\0"                                                \
 500         "download_cmd=tftp\0"                                           \
 501         "console_args=console=ttyS0,115200\0"                           \
 502         "root_args=root=/dev/nfs rw\0"                                  \
 503         "misc_args=ip=on\0"                                             \
 504         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 505         "bootfile=/home/user/file\0"                                    \
 506         "osfile=/home/user/board.uImage\0"                              \
 507         "fdtfile=/home/user/board.dtb\0"                                \
 508         "ubootfile=/home/user/u-boot.bin\0"                             \
 509         "fdtaddr=0x1e00000\0"                                           \
 510         "osaddr=0x1000000\0"                                            \
 511         "loadaddr=0x1000000\0"                                          \
 512         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 513         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 514         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 515         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 516         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 517         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 518         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 519         "bootcmd_flash1=run set_bootargs; "                             \
 520                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 521         "bootcmd_flash2=run set_bootargs; "                             \
 522                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 523         "bootcmd=run bootcmd_flash1\0"
 524 #endif  /* __CONFIG_H */