include/configs/xpedite517x.h

   1 /*
   2  * Copyright 2009 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * xpedite517x board configuration file
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_XPEDITE5140      1       /* MPC8641HPCN board specific */
  18 #define CONFIG_SYS_BOARD_NAME   "XPedite5170"
  19 #define CONFIG_SYS_FORM_3U_VPX  1
  20 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  21 #define CONFIG_BOARD_EARLY_INIT_R       /* Call board_pre_init */
  22 #define CONFIG_BAT_RW           1       /* Use common BAT rw code */
  23 #define CONFIG_HIGH_BATS        1       /* High BATs supported and enabled */
  24 #define CONFIG_ALTIVEC          1
  25
  26 #define CONFIG_SYS_TEXT_BASE    0xfff00000
  27
  28 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  29 #define CONFIG_PCIE1            1       /* PCIE controller 1 */
  30 #define CONFIG_PCIE2            1       /* PCIE controller 2 */
  31 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  32 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  33 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  34
  35 /*
  36  * DDR config
  37  */
  38 #define CONFIG_SYS_FSL_DDR2
  39 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  40 #define CONFIG_DDR_SPD
  41 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  42 #define SPD_EEPROM_ADDRESS1             0x54    /* Both channels use the */
  43 #define SPD_EEPROM_ADDRESS2             0x54    /* same SPD data         */
  44 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  45 #define CONFIG_NUM_DDR_CONTROLLERS      2
  46 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  47 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  48 #define CONFIG_DDR_ECC
  49 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  50 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
  51 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  52 #define CONFIG_VERY_BIG_RAM
  53 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
  54
  55 /*
  56  * virtual address to be used for temporary mappings.  There
  57  * should be 128k free at this VA.
  58  */
  59 #define CONFIG_SYS_SCRATCH_VA   0xe0000000
  60
  61 #ifndef __ASSEMBLY__
  62 extern unsigned long get_board_sys_clk(unsigned long dummy);
  63 #endif
  64
  65 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC86xx */
  66
  67 /*
  68  * L2CR setup
  69  */
  70 #define CONFIG_SYS_L2
  71 #define L2_INIT         0
  72 #define L2_ENABLE       (L2CR_L2E)
  73
  74 /*
  75  * Base addresses -- Note these are effective addresses where the
  76  * actual resources get mapped (not physical addresses)
  77  */
  78 #define CONFIG_SYS_CCSRBAR              0xef000000      /* relocated CCSRBAR */
  79 #define CONFIG_SYS_CCSRBAR_PHYS         CONFIG_SYS_CCSRBAR
  80 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  81 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    0x0
  82 #define CONFIG_SYS_IMMR                 CONFIG_SYS_CCSRBAR
  83
  84 /*
  85  * Diagnostics
  86  */
  87 #define CONFIG_SYS_ALT_MEMTEST
  88 #define CONFIG_SYS_MEMTEST_START        0x10000000
  89 #define CONFIG_SYS_MEMTEST_END          0x20000000
  90 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY |\
  91                                          CONFIG_SYS_POST_I2C)
  92 #define I2C_ADDR_LIST                   {CONFIG_SYS_I2C_DS1621_ADDR,    \
  93                                          CONFIG_SYS_I2C_DS4510_ADDR,    \
  94                                          CONFIG_SYS_I2C_EEPROM_ADDR,    \
  95                                          CONFIG_SYS_I2C_LM90_ADDR,      \
  96                                          CONFIG_SYS_I2C_PCA9553_ADDR,   \
  97                                          CONFIG_SYS_I2C_PCA953X_ADDR0,  \
  98                                          CONFIG_SYS_I2C_PCA953X_ADDR1,  \
  99                                          CONFIG_SYS_I2C_PCA953X_ADDR2,  \
 100                                          CONFIG_SYS_I2C_PCA953X_ADDR3,  \
 101                                          CONFIG_SYS_I2C_PEX8518_ADDR,   \
 102                                          CONFIG_SYS_I2C_RTC_ADDR}
 103 /* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
 104 #define I2C_ADDR_IGNORE_LIST            {0x50}
 105
 106 /*
 107  * Memory map
 108  * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
 109  * 0x8000_0000  0xbfff_ffff     PCIe1 Mem               1G non-cacheable
 110  * 0xc000_0000  0xcfff_ffff     PCIe2 Mem               256M non-cacheable
 111  * 0xe000_0000  0xe7ff_ffff     SRAM/SSRAM/L1 Cache     128M non-cacheable
 112  * 0xe800_0000  0xe87f_ffff     PCIe1 IO                8M non-cacheable
 113  * 0xe880_0000  0xe8ff_ffff     PCIe2 IO                8M non-cacheable
 114  * 0xef00_0000  0xef0f_ffff     CCSR/IMMR               1M non-cacheable
 115  * 0xef80_0000  0xef8f_ffff     NAND Flash              1M non-cacheable
 116  * 0xf000_0000  0xf7ff_ffff     NOR Flash 2             128M non-cacheable
 117  * 0xf800_0000  0xffff_ffff     NOR Flash 1             128M non-cacheable
 118  */
 119
 120 #define CONFIG_SYS_LBC_LCRR             (LCRR_CLKDIV_4 | LCRR_EADC_3)
 121
 122 /*
 123  * NAND flash configuration
 124  */
 125 #define CONFIG_SYS_NAND_BASE            0xef800000
 126 #define CONFIG_SYS_NAND_BASE2           0xef840000      /* Unused at this time */
 127 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
 128 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 129 #define CONFIG_NAND_ACTL
 130 #define CONFIG_SYS_NAND_ACTL_ALE        (1 << 14)       /* C_LA14 */
 131 #define CONFIG_SYS_NAND_ACTL_CLE        (1 << 15)       /* C_LA15 */
 132 #define CONFIG_SYS_NAND_ACTL_NCE        0               /* NCE not controlled by ADDR */
 133 #define CONFIG_SYS_NAND_ACTL_DELAY      25
 134 #define CONFIG_JFFS2_NAND
 135
 136 /*
 137  * NOR flash configuration
 138  */
 139 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 140 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 141 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 142 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 143 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 144 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 145 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 146 #define CONFIG_FLASH_CFI_DRIVER
 147 #define CONFIG_SYS_FLASH_CFI
 148 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 149 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff00000, 0xc0000}, \
 150                                                   {0xf7f00000, 0xc0000} }
 151 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 152 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 153
 154 /*
 155  * Chip select configuration
 156  */
 157 /* NOR Flash 0 on CS0 */
 158 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  |\
 159                                  BR_PS_16               |\
 160                                  BR_V)
 161 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            |\
 162                                  OR_GPCM_CSNT           |\
 163                                  OR_GPCM_XACS           |\
 164                                  OR_GPCM_ACS_DIV2       |\
 165                                  OR_GPCM_SCY_8          |\
 166                                  OR_GPCM_TRLX           |\
 167                                  OR_GPCM_EHTR           |\
 168                                  OR_GPCM_EAD)
 169
 170 /* NOR Flash 1 on CS1 */
 171 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 |\
 172                                  BR_PS_16               |\
 173                                  BR_V)
 174 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 175
 176 /* NAND flash on CS2 */
 177 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   |\
 178                                  BR_PS_8                |\
 179                                  BR_V)
 180 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB            |\
 181                                  OR_GPCM_BCTLD          |\
 182                                  OR_GPCM_CSNT           |\
 183                                  OR_GPCM_ACS_DIV4       |\
 184                                  OR_GPCM_SCY_4          |\
 185                                  OR_GPCM_TRLX           |\
 186                                  OR_GPCM_EHTR)
 187
 188 /* Optional NAND flash on CS3 */
 189 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  |\
 190                                  BR_PS_8                |\
 191                                  BR_V)
 192 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 193
 194 /*
 195  * Use L1 as initial stack
 196  */
 197 #define CONFIG_SYS_INIT_RAM_LOCK        1
 198 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 199 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 200
 201 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 202 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 203
 204 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 205 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 206
 207 /*
 208  * Serial Port
 209  */
 210 #define CONFIG_CONS_INDEX               1
 211 #define CONFIG_SYS_NS16550_SERIAL
 212 #define CONFIG_SYS_NS16550_REG_SIZE     1
 213 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 214 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 215 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 216 #define CONFIG_SYS_BAUDRATE_TABLE       \
 217         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 218 #define CONFIG_BAUDRATE                 115200
 219 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 220 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 221
 222 /*
 223  * I2C
 224  */
 225 #define CONFIG_SYS_I2C
 226 #define CONFIG_SYS_I2C_FSL
 227 #define CONFIG_SYS_FSL_I2C_SPEED        100000
 228 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 229 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 230 #define CONFIG_SYS_FSL_I2C2_SPEED       100000
 231 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 232 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 233
 234 /* PEX8518 slave I2C interface */
 235 #define CONFIG_SYS_I2C_PEX8518_ADDR     0x70
 236
 237 /* I2C DS1631 temperature sensor */
 238 #define CONFIG_SYS_I2C_DS1621_ADDR      0x48
 239 #define CONFIG_DTT_DS1621
 240 #define CONFIG_DTT_SENSORS              { 0 }
 241 #define CONFIG_SYS_I2C_LM90_ADDR        0x4c
 242
 243 /* I2C EEPROM - AT24C128B */
 244 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 245 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 246 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 247 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 248
 249 /* I2C RTC */
 250 #define CONFIG_RTC_M41T11               1
 251 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 252 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 253
 254 /* GPIO/EEPROM/SRAM */
 255 #define CONFIG_DS4510
 256 #define CONFIG_SYS_I2C_DS4510_ADDR      0x51
 257
 258 /* GPIO */
 259 #define CONFIG_PCA953X
 260 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 261 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 262 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 263 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 264 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 265 #define CONFIG_SYS_I2C_PCA9553_ADDR     0x62
 266
 267 /*
 268  * PU = pulled high, PD = pulled low
 269  * I = input, O = output, IO = input/output
 270  */
 271 /* PCA9557 @ 0x18*/
 272 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 273 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select */
 274 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 275 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select */
 276 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 277 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Set to 0 to enable NVM writing */
 278
 279 /* PCA9557 @ 0x1c*/
 280 #define CONFIG_SYS_PCA953X_XMC0_ROOT0           0x01 /* PU; Low if XMC is RC */
 281 #define CONFIG_SYS_PCA953X_PLUG_GPIO0           0x02 /* Samtec connector GPIO */
 282 #define CONFIG_SYS_PCA953X_XMC0_WAKE            0x04 /* PU; XMC wake */
 283 #define CONFIG_SYS_PCA953X_XMC0_BIST            0x08 /* PU; XMC built in self test */
 284 #define CONFIG_SYS_PCA953X_XMC_PRESENT          0x10 /* PU; Low if XMC module installed */
 285 #define CONFIG_SYS_PCA953X_PMC_PRESENT          0x20 /* PU; Low if PMC module installed */
 286 #define CONFIG_SYS_PCA953X_PMC0_MONARCH         0x40 /* PMC monarch mode enable */
 287 #define CONFIG_SYS_PCA953X_PMC0_EREADY          0x80 /* PU; PMC PCI eready */
 288
 289 /* PCA9557 @ 0x1e*/
 290 #define CONFIG_SYS_PCA953X_P0_GA0               0x01 /* PU; VPX Geographical address */
 291 #define CONFIG_SYS_PCA953X_P0_GA1               0x02 /* PU; VPX Geographical address */
 292 #define CONFIG_SYS_PCA953X_P0_GA2               0x04 /* PU; VPX Geographical address */
 293 #define CONFIG_SYS_PCA953X_P0_GA3               0x08 /* PU; VPX Geographical address */
 294 #define CONFIG_SYS_PCA953X_P0_GA4               0x10 /* PU; VPX Geographical address */
 295 #define CONFIG_SYS_PCA953X_P0_GAP               0x20 /* PU; VPX Geographical address parity */
 296 #define CONFIG_SYS_PCA953X_P1_SYSEN             0x80 /* PU; VPX P1 SYSCON */
 297
 298 /* PCA9557 @ 0x1f */
 299 #define CONFIG_SYS_PCA953X_VPX_GPIO0            0x01 /* PU; VPX P15 GPIO */
 300 #define CONFIG_SYS_PCA953X_VPX_GPIO1            0x02 /* PU; VPX P15 GPIO */
 301 #define CONFIG_SYS_PCA953X_VPX_GPIO2            0x04 /* PU; VPX P15 GPIO */
 302 #define CONFIG_SYS_PCA953X_VPX_GPIO3            0x08 /* PU; VPX P15 GPIO */
 303
 304 /*
 305  * General PCI
 306  * Memory space is mapped 1-1, but I/O space must start from 0.
 307  */
 308 /* PCIE1 - PEX8518 */
 309 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 310 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 311 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 312 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 313 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 314 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 315
 316 /* PCIE2 - VPX P1 */
 317 #define CONFIG_SYS_PCIE2_MEM_BUS        0xc0000000
 318 #define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
 319 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
 320 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 321 #define CONFIG_SYS_PCIE2_IO_PHYS        0xe8800000
 322 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000      /* 8M */
 323
 324 /*
 325  * Networking options
 326  */
 327 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
 328 #define CONFIG_PHY_GIGE         1       /* Include GbE speed/duplex detection */
 329 #define CONFIG_MII              1       /* MII PHY management */
 330 #define CONFIG_ETHPRIME         "eTSEC1"
 331
 332 #define CONFIG_TSEC1            1
 333 #define CONFIG_TSEC1_NAME       "eTSEC1"
 334 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 335 #define TSEC1_PHY_ADDR          1
 336 #define TSEC1_PHYIDX            0
 337 #define CONFIG_HAS_ETH0
 338
 339 #define CONFIG_TSEC2            1
 340 #define CONFIG_TSEC2_NAME       "eTSEC2"
 341 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 342 #define TSEC2_PHY_ADDR          2
 343 #define TSEC2_PHYIDX            0
 344 #define CONFIG_HAS_ETH1
 345
 346 /*
 347  * BAT mappings
 348  */
 349 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 350 #define CONFIG_SYS_CCSR_DEFAULT_DBATL   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 351                                          BATL_PP_RW                     |\
 352                                          BATL_CACHEINHIBIT              |\
 353                                          BATL_GUARDEDSTORAGE)
 354 #define CONFIG_SYS_CCSR_DEFAULT_DBATU   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 355                                          BATU_BL_1M                     |\
 356                                          BATU_VS                        |\
 357                                          BATU_VP)
 358 #define CONFIG_SYS_CCSR_DEFAULT_IBATL   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 359                                          BATL_PP_RW                     |\
 360                                          BATL_CACHEINHIBIT)
 361 #define CONFIG_SYS_CCSR_DEFAULT_IBATU   CONFIG_SYS_CCSR_DEFAULT_DBATU
 362 #endif
 363
 364 /*
 365  * BAT0         2G      Cacheable, non-guarded
 366  * 0x0000_0000  2G      DDR
 367  */
 368 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 369 #define CONFIG_SYS_DBAT0U       (BATU_BL_2G | BATU_VS | BATU_VP)
 370 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 371 #define CONFIG_SYS_IBAT0U       CONFIG_SYS_DBAT0U
 372
 373 /*
 374  * BAT1         1G      Cache-inhibited, guarded
 375  * 0x8000_0000  1G      PCI-Express 1 Memory
 376  */
 377 #define CONFIG_SYS_DBAT1L       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 378                                  BATL_PP_RW                     |\
 379                                  BATL_CACHEINHIBIT              |\
 380                                  BATL_GUARDEDSTORAGE)
 381 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 382                                  BATU_BL_1G                     |\
 383                                  BATU_VS                        |\
 384                                  BATU_VP)
 385 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 386                                  BATL_PP_RW                     |\
 387                                  BATL_CACHEINHIBIT)
 388 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 389
 390 /*
 391  * BAT2         512M    Cache-inhibited, guarded
 392  * 0xc000_0000  512M    PCI-Express 2 Memory
 393  */
 394 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 395                                  BATL_PP_RW                     |\
 396                                  BATL_CACHEINHIBIT              |\
 397                                  BATL_GUARDEDSTORAGE)
 398 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 399                                  BATU_BL_512M                   |\
 400                                  BATU_VS                        |\
 401                                  BATU_VP)
 402 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 403                                  BATL_PP_RW                     |\
 404                                  BATL_CACHEINHIBIT)
 405 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 406
 407 /*
 408  * BAT3         1M      Cache-inhibited, guarded
 409  * 0xe000_0000  1M      CCSR
 410  */
 411 #define CONFIG_SYS_DBAT3L       (CONFIG_SYS_CCSRBAR             |\
 412                                  BATL_PP_RW                     |\
 413                                  BATL_CACHEINHIBIT              |\
 414                                  BATL_GUARDEDSTORAGE)
 415 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR             |\
 416                                  BATU_BL_1M                     |\
 417                                  BATU_VS                        |\
 418                                  BATU_VP)
 419 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_CCSRBAR             |\
 420                                  BATL_PP_RW                     |\
 421                                  BATL_CACHEINHIBIT)
 422 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 423
 424 /*
 425  * BAT4         32M     Cache-inhibited, guarded
 426  * 0xe200_0000  16M     PCI-Express 1 I/O
 427  * 0xe300_0000  16M     PCI-Express 2 I/0
 428  */
 429 #define CONFIG_SYS_DBAT4L       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 430                                  BATL_PP_RW                     |\
 431                                  BATL_CACHEINHIBIT              |\
 432                                  BATL_GUARDEDSTORAGE)
 433 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 434                                  BATU_BL_32M                    |\
 435                                  BATU_VS                        |\
 436                                  BATU_VP)
 437 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 438                                  BATL_PP_RW                     |\
 439                                  BATL_CACHEINHIBIT)
 440 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 441
 442 /*
 443  * BAT5         128K    Cacheable, non-guarded
 444  * 0xe400_1000  128K    Init RAM for stack in the CPU DCache (no backing memory)
 445  */
 446 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR       |\
 447                                  BATL_PP_RW                     |\
 448                                  BATL_MEMCOHERENCE)
 449 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR       |\
 450                                  BATU_BL_128K                   |\
 451                                  BATU_VS                        |\
 452                                  BATU_VP)
 453 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 454 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 455
 456 /*
 457  * BAT6         256M    Cache-inhibited, guarded
 458  * 0xf000_0000  256M    FLASH
 459  */
 460 #define CONFIG_SYS_DBAT6L       (CONFIG_SYS_FLASH_BASE2         |\
 461                                  BATL_PP_RW                     |\
 462                                  BATL_CACHEINHIBIT              |\
 463                                  BATL_GUARDEDSTORAGE)
 464 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE          |\
 465                                  BATU_BL_256M                   |\
 466                                  BATU_VS                        |\
 467                                  BATU_VP)
 468 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_FLASH_BASE          |\
 469                                  BATL_PP_RW                     |\
 470                                  BATL_MEMCOHERENCE)
 471 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 472
 473 /* Map the last 1M of flash where we're running from reset */
 474 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY  |\
 475                                  BATL_PP_RW                     |\
 476                                  BATL_CACHEINHIBIT              |\
 477                                  BATL_GUARDEDSTORAGE)
 478 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE                   |\
 479                                  BATU_BL_1M                     |\
 480                                  BATU_VS                        |\
 481                                  BATU_VP)
 482 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY  |\
 483                                  BATL_PP_RW                     |\
 484                                  BATL_MEMCOHERENCE)
 485 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 486
 487 /*
 488  * BAT7         64M     Cache-inhibited, guarded
 489  * 0xe800_0000  64K     NAND FLASH
 490  * 0xe804_0000  128K    DUART Registers
 491  */
 492 #define CONFIG_SYS_DBAT7L       (CONFIG_SYS_NAND_BASE           |\
 493                                  BATL_PP_RW                     |\
 494                                  BATL_CACHEINHIBIT              |\
 495                                  BATL_GUARDEDSTORAGE)
 496 #define CONFIG_SYS_DBAT7U       (CONFIG_SYS_NAND_BASE           |\
 497                                  BATU_BL_512K                   |\
 498                                  BATU_VS                        |\
 499                                  BATU_VP)
 500 #define CONFIG_SYS_IBAT7L       (CONFIG_SYS_NAND_BASE           |\
 501                                  BATL_PP_RW                     |\
 502                                  BATL_CACHEINHIBIT)
 503 #define CONFIG_SYS_IBAT7U       CONFIG_SYS_DBAT7U
 504
 505 /*
 506  * Command configuration.
 507  */
 508 #define CONFIG_CMD_DATE
 509 #define CONFIG_CMD_DS4510
 510 #define CONFIG_CMD_DS4510_INFO
 511 #define CONFIG_CMD_DTT
 512 #define CONFIG_CMD_EEPROM
 513 #define CONFIG_CMD_IRQ
 514 #define CONFIG_CMD_JFFS2
 515 #define CONFIG_CMD_NAND
 516 #define CONFIG_CMD_PCA953X
 517 #define CONFIG_CMD_PCA953X_INFO
 518 #define CONFIG_CMD_PCI
 519 #define CONFIG_CMD_PCI_ENUM
 520 #define CONFIG_CMD_REGINFO
 521
 522 /*
 523  * Miscellaneous configurable options
 524  */
 525 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 526 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 527 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 528 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 529 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 530 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 531 #define CONFIG_CMDLINE_EDITING  1               /* Command-line editing */
 532 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 533 #define CONFIG_PANIC_HANG                       /* do not reset board on panic */
 534 #define CONFIG_PREBOOT                          /* enable preboot variable */
 535 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 536
 537 /*
 538  * For booting Linux, the board info and command line data
 539  * have to be in the first 16 MB of memory, since this is
 540  * the maximum mapped by the Linux kernel during initialization.
 541  */
 542 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 543 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 544
 545 /*
 546  * Environment Configuration
 547  */
 548 #define CONFIG_ENV_IS_IN_FLASH  1
 549 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 550 #define CONFIG_ENV_SIZE         0x8000
 551 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 552
 553 /*
 554  * Flash memory map:
 555  * fffc0000 - ffffffff  Pri FDT (256KB)
 556  * fff80000 - fffbffff  Pri U-Boot Environment (256 KB)
 557  * fff00000 - fff7ffff  Pri U-Boot (512 KB)
 558  * fef00000 - ffefffff  Pri OS image (16MB)
 559  * f8000000 - feefffff  Pri OS Use/Filesystem (111MB)
 560  *
 561  * f7fc0000 - f7ffffff  Sec FDT (256KB)
 562  * f7f80000 - f7fbffff  Sec U-Boot Environment (256 KB)
 563  * f7f00000 - f7f7ffff  Sec U-Boot (512 KB)
 564  * f6f00000 - f7efffff  Sec OS image (16MB)
 565  * f0000000 - f6efffff  Sec OS Use/Filesystem (111MB)
 566  */
 567 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff00000)
 568 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f00000)
 569 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfffc0000)
 570 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7fc0000)
 571 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 572 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 573
 574 #define CONFIG_PROG_UBOOT1                                              \
 575         "$download_cmd $loadaddr $ubootfile; "                          \
 576         "if test $? -eq 0; then "                                       \
 577                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 578                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 579                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 580                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 581                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 582                 "if test $? -ne 0; then "                               \
 583                         "echo PROGRAM FAILED; "                         \
 584                 "else; "                                                \
 585                         "echo PROGRAM SUCCEEDED; "                      \
 586                 "fi; "                                                  \
 587         "else; "                                                        \
 588                 "echo DOWNLOAD FAILED; "                                \
 589         "fi;"
 590
 591 #define CONFIG_PROG_UBOOT2                                              \
 592         "$download_cmd $loadaddr $ubootfile; "                          \
 593         "if test $? -eq 0; then "                                       \
 594                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 595                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 596                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 597                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 598                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 599                 "if test $? -ne 0; then "                               \
 600                         "echo PROGRAM FAILED; "                         \
 601                 "else; "                                                \
 602                         "echo PROGRAM SUCCEEDED; "                      \
 603                 "fi; "                                                  \
 604         "else; "                                                        \
 605                 "echo DOWNLOAD FAILED; "                                \
 606         "fi;"
 607
 608 #define CONFIG_BOOT_OS_NET                                              \
 609         "$download_cmd $osaddr $osfile; "                               \
 610         "if test $? -eq 0; then "                                       \
 611                 "if test -n $fdtaddr; then "                            \
 612                         "$download_cmd $fdtaddr $fdtfile; "             \
 613                         "if test $? -eq 0; then "                       \
 614                                 "bootm $osaddr - $fdtaddr; "            \
 615                         "else; "                                        \
 616                                 "echo FDT DOWNLOAD FAILED; "            \
 617                         "fi; "                                          \
 618                 "else; "                                                \
 619                         "bootm $osaddr; "                               \
 620                 "fi; "                                                  \
 621         "else; "                                                        \
 622                 "echo OS DOWNLOAD FAILED; "                             \
 623         "fi;"
 624
 625 #define CONFIG_PROG_OS1                                                 \
 626         "$download_cmd $osaddr $osfile; "                               \
 627         "if test $? -eq 0; then "                                       \
 628                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 629                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 630                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 631                 "if test $? -ne 0; then "                               \
 632                         "echo OS PROGRAM FAILED; "                      \
 633                 "else; "                                                \
 634                         "echo OS PROGRAM SUCCEEDED; "                   \
 635                 "fi; "                                                  \
 636         "else; "                                                        \
 637                 "echo OS DOWNLOAD FAILED; "                             \
 638         "fi;"
 639
 640 #define CONFIG_PROG_OS2                                                 \
 641         "$download_cmd $osaddr $osfile; "                               \
 642         "if test $? -eq 0; then "                                       \
 643                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 644                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 645                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 646                 "if test $? -ne 0; then "                               \
 647                         "echo OS PROGRAM FAILED; "                      \
 648                 "else; "                                                \
 649                         "echo OS PROGRAM SUCCEEDED; "                   \
 650                 "fi; "                                                  \
 651         "else; "                                                        \
 652                 "echo OS DOWNLOAD FAILED; "                             \
 653         "fi;"
 654
 655 #define CONFIG_PROG_FDT1                                                \
 656         "$download_cmd $fdtaddr $fdtfile; "                             \
 657         "if test $? -eq 0; then "                                       \
 658                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 659                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 660                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 661                 "if test $? -ne 0; then "                               \
 662                         "echo FDT PROGRAM FAILED; "                     \
 663                 "else; "                                                \
 664                         "echo FDT PROGRAM SUCCEEDED; "                  \
 665                 "fi; "                                                  \
 666         "else; "                                                        \
 667                 "echo FDT DOWNLOAD FAILED; "                            \
 668         "fi;"
 669
 670 #define CONFIG_PROG_FDT2                                                \
 671         "$download_cmd $fdtaddr $fdtfile; "                             \
 672         "if test $? -eq 0; then "                                       \
 673                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 674                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 675                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 676                 "if test $? -ne 0; then "                               \
 677                         "echo FDT PROGRAM FAILED; "                     \
 678                 "else; "                                                \
 679                         "echo FDT PROGRAM SUCCEEDED; "                  \
 680                 "fi; "                                                  \
 681         "else; "                                                        \
 682                 "echo FDT DOWNLOAD FAILED; "                            \
 683         "fi;"
 684
 685 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 686         "autoload=yes\0"                                                \
 687         "download_cmd=tftp\0"                                           \
 688         "console_args=console=ttyS0,115200\0"                           \
 689         "root_args=root=/dev/nfs rw\0"                                  \
 690         "misc_args=ip=on\0"                                             \
 691         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 692         "bootfile=/home/user/file\0"                                    \
 693         "osfile=/home/user/board.uImage\0"                              \
 694         "fdtfile=/home/user/board.dtb\0"                                \
 695         "ubootfile=/home/user/u-boot.bin\0"                             \
 696         "fdtaddr=0x1e00000\0"                                           \
 697         "osaddr=0x1000000\0"                                            \
 698         "loadaddr=0x1000000\0"                                          \
 699         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 700         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 701         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 702         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 703         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 704         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 705         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 706         "bootcmd_flash1=run set_bootargs; "                             \
 707                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 708         "bootcmd_flash2=run set_bootargs; "                             \
 709                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 710         "bootcmd=run bootcmd_flash1\0"
 711 #endif  /* __CONFIG_H */