include/configs/xpedite517x.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2009 Extreme Engineering Solutions, Inc.
   4  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   5  */
   6
   7 /*
   8  * xpedite517x board configuration file
   9  */
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 /*
  14  * High Level Configuration Options
  15  */
  16 #define CONFIG_SYS_BOARD_NAME   "XPedite5170"
  17 #define CONFIG_SYS_FORM_3U_VPX  1
  18 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  19 #define CONFIG_BAT_RW           1       /* Use common BAT rw code */
  20 #define CONFIG_ALTIVEC          1
  21
  22 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  23 #define CONFIG_PCIE1            1       /* PCIE controller 1 */
  24 #define CONFIG_PCIE2            1       /* PCIE controller 2 */
  25 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  26 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  27 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  28
  29 /*
  30  * DDR config
  31  */
  32 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  33 #define CONFIG_DDR_SPD
  34 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  35 #define SPD_EEPROM_ADDRESS1             0x54    /* Both channels use the */
  36 #define SPD_EEPROM_ADDRESS2             0x54    /* same SPD data         */
  37 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  38 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  39 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  40 #define CONFIG_DDR_ECC
  41 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  42 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
  43 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  44 #define CONFIG_VERY_BIG_RAM
  45 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
  46
  47 /*
  48  * virtual address to be used for temporary mappings.  There
  49  * should be 128k free at this VA.
  50  */
  51 #define CONFIG_SYS_SCRATCH_VA   0xe0000000
  52
  53 #ifndef __ASSEMBLY__
  54 extern unsigned long get_board_sys_clk(unsigned long dummy);
  55 #endif
  56
  57 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC86xx */
  58
  59 /*
  60  * L2CR setup
  61  */
  62 #define CONFIG_SYS_L2
  63 #define L2_INIT         0
  64 #define L2_ENABLE       (L2CR_L2E)
  65
  66 /*
  67  * Base addresses -- Note these are effective addresses where the
  68  * actual resources get mapped (not physical addresses)
  69  */
  70 #define CONFIG_SYS_CCSRBAR              0xef000000      /* relocated CCSRBAR */
  71 #define CONFIG_SYS_CCSRBAR_PHYS         CONFIG_SYS_CCSRBAR
  72 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  73 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    0x0
  74 #define CONFIG_SYS_IMMR                 CONFIG_SYS_CCSRBAR
  75
  76 /*
  77  * Diagnostics
  78  */
  79 #define CONFIG_SYS_MEMTEST_START        0x10000000
  80 #define CONFIG_SYS_MEMTEST_END          0x20000000
  81 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY |\
  82                                          CONFIG_SYS_POST_I2C)
  83 /* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
  84 #define I2C_ADDR_IGNORE_LIST            {0x50}
  85
  86 /*
  87  * Memory map
  88  * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
  89  * 0x8000_0000  0xbfff_ffff     PCIe1 Mem               1G non-cacheable
  90  * 0xc000_0000  0xcfff_ffff     PCIe2 Mem               256M non-cacheable
  91  * 0xe000_0000  0xe7ff_ffff     SRAM/SSRAM/L1 Cache     128M non-cacheable
  92  * 0xe800_0000  0xe87f_ffff     PCIe1 IO                8M non-cacheable
  93  * 0xe880_0000  0xe8ff_ffff     PCIe2 IO                8M non-cacheable
  94  * 0xef00_0000  0xef0f_ffff     CCSR/IMMR               1M non-cacheable
  95  * 0xef80_0000  0xef8f_ffff     NAND Flash              1M non-cacheable
  96  * 0xf000_0000  0xf7ff_ffff     NOR Flash 2             128M non-cacheable
  97  * 0xf800_0000  0xffff_ffff     NOR Flash 1             128M non-cacheable
  98  */
  99
 100 #define CONFIG_SYS_LBC_LCRR             (LCRR_CLKDIV_4 | LCRR_EADC_3)
 101
 102 /*
 103  * NAND flash configuration
 104  */
 105 #define CONFIG_SYS_NAND_BASE            0xef800000
 106 #define CONFIG_SYS_NAND_BASE2           0xef840000      /* Unused at this time */
 107 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
 108 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 109 #define CONFIG_NAND_ACTL
 110 #define CONFIG_SYS_NAND_ACTL_ALE        (1 << 14)       /* C_LA14 */
 111 #define CONFIG_SYS_NAND_ACTL_CLE        (1 << 15)       /* C_LA15 */
 112 #define CONFIG_SYS_NAND_ACTL_NCE        0               /* NCE not controlled by ADDR */
 113 #define CONFIG_SYS_NAND_ACTL_DELAY      25
 114 #define CONFIG_JFFS2_NAND
 115
 116 /*
 117  * NOR flash configuration
 118  */
 119 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 120 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 121 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 122 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 123 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 124 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 125 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 126 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff00000, 0xc0000}, \
 127                                                   {0xf7f00000, 0xc0000} }
 128 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 129 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 130
 131 /*
 132  * Chip select configuration
 133  */
 134 /* NOR Flash 0 on CS0 */
 135 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  |\
 136                                  BR_PS_16               |\
 137                                  BR_V)
 138 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            |\
 139                                  OR_GPCM_CSNT           |\
 140                                  OR_GPCM_XACS           |\
 141                                  OR_GPCM_ACS_DIV2       |\
 142                                  OR_GPCM_SCY_8          |\
 143                                  OR_GPCM_TRLX           |\
 144                                  OR_GPCM_EHTR           |\
 145                                  OR_GPCM_EAD)
 146
 147 /* NOR Flash 1 on CS1 */
 148 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 |\
 149                                  BR_PS_16               |\
 150                                  BR_V)
 151 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 152
 153 /* NAND flash on CS2 */
 154 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   |\
 155                                  BR_PS_8                |\
 156                                  BR_V)
 157 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB            |\
 158                                  OR_GPCM_BCTLD          |\
 159                                  OR_GPCM_CSNT           |\
 160                                  OR_GPCM_ACS_DIV4       |\
 161                                  OR_GPCM_SCY_4          |\
 162                                  OR_GPCM_TRLX           |\
 163                                  OR_GPCM_EHTR)
 164
 165 /* Optional NAND flash on CS3 */
 166 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  |\
 167                                  BR_PS_8                |\
 168                                  BR_V)
 169 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 170
 171 /*
 172  * Use L1 as initial stack
 173  */
 174 #define CONFIG_SYS_INIT_RAM_LOCK        1
 175 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 176 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 177
 178 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 179 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 180
 181 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 182 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 183
 184 /*
 185  * Serial Port
 186  */
 187 #define CONFIG_SYS_NS16550_SERIAL
 188 #define CONFIG_SYS_NS16550_REG_SIZE     1
 189 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 190 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 191 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 192 #define CONFIG_SYS_BAUDRATE_TABLE       \
 193         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 194 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 195 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 196
 197 /*
 198  * I2C
 199  */
 200 #define CONFIG_SYS_I2C
 201 #define CONFIG_SYS_I2C_FSL
 202 #define CONFIG_SYS_FSL_I2C_SPEED        100000
 203 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 204 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 205 #define CONFIG_SYS_FSL_I2C2_SPEED       100000
 206 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 207 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 208
 209 /* PEX8518 slave I2C interface */
 210 #define CONFIG_SYS_I2C_PEX8518_ADDR     0x70
 211
 212 /* I2C DS1631 temperature sensor */
 213 #define CONFIG_SYS_I2C_LM90_ADDR        0x4c
 214
 215 /* I2C EEPROM - AT24C128B */
 216 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 217 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 218 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 219 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 220
 221 /* I2C RTC */
 222 #define CONFIG_RTC_M41T11               1
 223 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 224 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 225
 226 /* GPIO */
 227 #define CONFIG_PCA953X
 228 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 229 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 230 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 231 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 232 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 233 #define CONFIG_SYS_I2C_PCA9553_ADDR     0x62
 234
 235 /*
 236  * PU = pulled high, PD = pulled low
 237  * I = input, O = output, IO = input/output
 238  */
 239 /* PCA9557 @ 0x18*/
 240 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 241 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select */
 242 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 243 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select */
 244 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 245 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Set to 0 to enable NVM writing */
 246
 247 /* PCA9557 @ 0x1c*/
 248 #define CONFIG_SYS_PCA953X_XMC0_ROOT0           0x01 /* PU; Low if XMC is RC */
 249 #define CONFIG_SYS_PCA953X_PLUG_GPIO0           0x02 /* Samtec connector GPIO */
 250 #define CONFIG_SYS_PCA953X_XMC0_WAKE            0x04 /* PU; XMC wake */
 251 #define CONFIG_SYS_PCA953X_XMC0_BIST            0x08 /* PU; XMC built in self test */
 252 #define CONFIG_SYS_PCA953X_XMC_PRESENT          0x10 /* PU; Low if XMC module installed */
 253 #define CONFIG_SYS_PCA953X_PMC_PRESENT          0x20 /* PU; Low if PMC module installed */
 254 #define CONFIG_SYS_PCA953X_PMC0_MONARCH         0x40 /* PMC monarch mode enable */
 255 #define CONFIG_SYS_PCA953X_PMC0_EREADY          0x80 /* PU; PMC PCI eready */
 256
 257 /* PCA9557 @ 0x1e*/
 258 #define CONFIG_SYS_PCA953X_P0_GA0               0x01 /* PU; VPX Geographical address */
 259 #define CONFIG_SYS_PCA953X_P0_GA1               0x02 /* PU; VPX Geographical address */
 260 #define CONFIG_SYS_PCA953X_P0_GA2               0x04 /* PU; VPX Geographical address */
 261 #define CONFIG_SYS_PCA953X_P0_GA3               0x08 /* PU; VPX Geographical address */
 262 #define CONFIG_SYS_PCA953X_P0_GA4               0x10 /* PU; VPX Geographical address */
 263 #define CONFIG_SYS_PCA953X_P0_GAP               0x20 /* PU; VPX Geographical address parity */
 264 #define CONFIG_SYS_PCA953X_P1_SYSEN             0x80 /* PU; VPX P1 SYSCON */
 265
 266 /* PCA9557 @ 0x1f */
 267 #define CONFIG_SYS_PCA953X_VPX_GPIO0            0x01 /* PU; VPX P15 GPIO */
 268 #define CONFIG_SYS_PCA953X_VPX_GPIO1            0x02 /* PU; VPX P15 GPIO */
 269 #define CONFIG_SYS_PCA953X_VPX_GPIO2            0x04 /* PU; VPX P15 GPIO */
 270 #define CONFIG_SYS_PCA953X_VPX_GPIO3            0x08 /* PU; VPX P15 GPIO */
 271
 272 /*
 273  * General PCI
 274  * Memory space is mapped 1-1, but I/O space must start from 0.
 275  */
 276 /* PCIE1 - PEX8518 */
 277 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 278 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 279 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 280 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 281 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 282 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 283
 284 /* PCIE2 - VPX P1 */
 285 #define CONFIG_SYS_PCIE2_MEM_BUS        0xc0000000
 286 #define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
 287 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
 288 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 289 #define CONFIG_SYS_PCIE2_IO_PHYS        0xe8800000
 290 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000      /* 8M */
 291
 292 /*
 293  * Networking options
 294  */
 295 #define CONFIG_ETHPRIME         "eTSEC1"
 296
 297 #define CONFIG_TSEC1            1
 298 #define CONFIG_TSEC1_NAME       "eTSEC1"
 299 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 300 #define TSEC1_PHY_ADDR          1
 301 #define TSEC1_PHYIDX            0
 302 #define CONFIG_HAS_ETH0
 303
 304 #define CONFIG_TSEC2            1
 305 #define CONFIG_TSEC2_NAME       "eTSEC2"
 306 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 307 #define TSEC2_PHY_ADDR          2
 308 #define TSEC2_PHYIDX            0
 309 #define CONFIG_HAS_ETH1
 310
 311 /*
 312  * BAT mappings
 313  */
 314 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 315 #define CONFIG_SYS_CCSR_DEFAULT_DBATL   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 316                                          BATL_PP_RW                     |\
 317                                          BATL_CACHEINHIBIT              |\
 318                                          BATL_GUARDEDSTORAGE)
 319 #define CONFIG_SYS_CCSR_DEFAULT_DBATU   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 320                                          BATU_BL_1M                     |\
 321                                          BATU_VS                        |\
 322                                          BATU_VP)
 323 #define CONFIG_SYS_CCSR_DEFAULT_IBATL   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 324                                          BATL_PP_RW                     |\
 325                                          BATL_CACHEINHIBIT)
 326 #define CONFIG_SYS_CCSR_DEFAULT_IBATU   CONFIG_SYS_CCSR_DEFAULT_DBATU
 327 #endif
 328
 329 /*
 330  * BAT0         2G      Cacheable, non-guarded
 331  * 0x0000_0000  2G      DDR
 332  */
 333 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 334 #define CONFIG_SYS_DBAT0U       (BATU_BL_2G | BATU_VS | BATU_VP)
 335 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 336 #define CONFIG_SYS_IBAT0U       CONFIG_SYS_DBAT0U
 337
 338 /*
 339  * BAT1         1G      Cache-inhibited, guarded
 340  * 0x8000_0000  1G      PCI-Express 1 Memory
 341  */
 342 #define CONFIG_SYS_DBAT1L       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 343                                  BATL_PP_RW                     |\
 344                                  BATL_CACHEINHIBIT              |\
 345                                  BATL_GUARDEDSTORAGE)
 346 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 347                                  BATU_BL_1G                     |\
 348                                  BATU_VS                        |\
 349                                  BATU_VP)
 350 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 351                                  BATL_PP_RW                     |\
 352                                  BATL_CACHEINHIBIT)
 353 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 354
 355 /*
 356  * BAT2         512M    Cache-inhibited, guarded
 357  * 0xc000_0000  512M    PCI-Express 2 Memory
 358  */
 359 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 360                                  BATL_PP_RW                     |\
 361                                  BATL_CACHEINHIBIT              |\
 362                                  BATL_GUARDEDSTORAGE)
 363 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 364                                  BATU_BL_512M                   |\
 365                                  BATU_VS                        |\
 366                                  BATU_VP)
 367 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 368                                  BATL_PP_RW                     |\
 369                                  BATL_CACHEINHIBIT)
 370 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 371
 372 /*
 373  * BAT3         1M      Cache-inhibited, guarded
 374  * 0xe000_0000  1M      CCSR
 375  */
 376 #define CONFIG_SYS_DBAT3L       (CONFIG_SYS_CCSRBAR             |\
 377                                  BATL_PP_RW                     |\
 378                                  BATL_CACHEINHIBIT              |\
 379                                  BATL_GUARDEDSTORAGE)
 380 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR             |\
 381                                  BATU_BL_1M                     |\
 382                                  BATU_VS                        |\
 383                                  BATU_VP)
 384 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_CCSRBAR             |\
 385                                  BATL_PP_RW                     |\
 386                                  BATL_CACHEINHIBIT)
 387 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 388
 389 /*
 390  * BAT4         32M     Cache-inhibited, guarded
 391  * 0xe200_0000  16M     PCI-Express 1 I/O
 392  * 0xe300_0000  16M     PCI-Express 2 I/0
 393  */
 394 #define CONFIG_SYS_DBAT4L       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 395                                  BATL_PP_RW                     |\
 396                                  BATL_CACHEINHIBIT              |\
 397                                  BATL_GUARDEDSTORAGE)
 398 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 399                                  BATU_BL_32M                    |\
 400                                  BATU_VS                        |\
 401                                  BATU_VP)
 402 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 403                                  BATL_PP_RW                     |\
 404                                  BATL_CACHEINHIBIT)
 405 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 406
 407 /*
 408  * BAT5         128K    Cacheable, non-guarded
 409  * 0xe400_1000  128K    Init RAM for stack in the CPU DCache (no backing memory)
 410  */
 411 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR       |\
 412                                  BATL_PP_RW                     |\
 413                                  BATL_MEMCOHERENCE)
 414 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR       |\
 415                                  BATU_BL_128K                   |\
 416                                  BATU_VS                        |\
 417                                  BATU_VP)
 418 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 419 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 420
 421 /*
 422  * BAT6         256M    Cache-inhibited, guarded
 423  * 0xf000_0000  256M    FLASH
 424  */
 425 #define CONFIG_SYS_DBAT6L       (CONFIG_SYS_FLASH_BASE2         |\
 426                                  BATL_PP_RW                     |\
 427                                  BATL_CACHEINHIBIT              |\
 428                                  BATL_GUARDEDSTORAGE)
 429 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE          |\
 430                                  BATU_BL_256M                   |\
 431                                  BATU_VS                        |\
 432                                  BATU_VP)
 433 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_FLASH_BASE          |\
 434                                  BATL_PP_RW                     |\
 435                                  BATL_MEMCOHERENCE)
 436 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 437
 438 /* Map the last 1M of flash where we're running from reset */
 439 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY  |\
 440                                  BATL_PP_RW                     |\
 441                                  BATL_CACHEINHIBIT              |\
 442                                  BATL_GUARDEDSTORAGE)
 443 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE                   |\
 444                                  BATU_BL_1M                     |\
 445                                  BATU_VS                        |\
 446                                  BATU_VP)
 447 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY  |\
 448                                  BATL_PP_RW                     |\
 449                                  BATL_MEMCOHERENCE)
 450 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 451
 452 /*
 453  * BAT7         64M     Cache-inhibited, guarded
 454  * 0xe800_0000  64K     NAND FLASH
 455  * 0xe804_0000  128K    DUART Registers
 456  */
 457 #define CONFIG_SYS_DBAT7L       (CONFIG_SYS_NAND_BASE           |\
 458                                  BATL_PP_RW                     |\
 459                                  BATL_CACHEINHIBIT              |\
 460                                  BATL_GUARDEDSTORAGE)
 461 #define CONFIG_SYS_DBAT7U       (CONFIG_SYS_NAND_BASE           |\
 462                                  BATU_BL_512K                   |\
 463                                  BATU_VS                        |\
 464                                  BATU_VP)
 465 #define CONFIG_SYS_IBAT7L       (CONFIG_SYS_NAND_BASE           |\
 466                                  BATL_PP_RW                     |\
 467                                  BATL_CACHEINHIBIT)
 468 #define CONFIG_SYS_IBAT7U       CONFIG_SYS_DBAT7U
 469
 470 /*
 471  * Miscellaneous configurable options
 472  */
 473 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 474 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 475 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 476
 477 /*
 478  * For booting Linux, the board info and command line data
 479  * have to be in the first 16 MB of memory, since this is
 480  * the maximum mapped by the Linux kernel during initialization.
 481  */
 482 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 483 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 484
 485 /*
 486  * Environment Configuration
 487  */
 488 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 489 #define CONFIG_ENV_SIZE         0x8000
 490 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 491
 492 /*
 493  * Flash memory map:
 494  * fffc0000 - ffffffff  Pri FDT (256KB)
 495  * fff80000 - fffbffff  Pri U-Boot Environment (256 KB)
 496  * fff00000 - fff7ffff  Pri U-Boot (512 KB)
 497  * fef00000 - ffefffff  Pri OS image (16MB)
 498  * f8000000 - feefffff  Pri OS Use/Filesystem (111MB)
 499  *
 500  * f7fc0000 - f7ffffff  Sec FDT (256KB)
 501  * f7f80000 - f7fbffff  Sec U-Boot Environment (256 KB)
 502  * f7f00000 - f7f7ffff  Sec U-Boot (512 KB)
 503  * f6f00000 - f7efffff  Sec OS image (16MB)
 504  * f0000000 - f6efffff  Sec OS Use/Filesystem (111MB)
 505  */
 506 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff00000)
 507 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f00000)
 508 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfffc0000)
 509 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7fc0000)
 510 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 511 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 512
 513 #define CONFIG_PROG_UBOOT1                                              \
 514         "$download_cmd $loadaddr $ubootfile; "                          \
 515         "if test $? -eq 0; then "                                       \
 516                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 517                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 518                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 519                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 520                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 521                 "if test $? -ne 0; then "                               \
 522                         "echo PROGRAM FAILED; "                         \
 523                 "else; "                                                \
 524                         "echo PROGRAM SUCCEEDED; "                      \
 525                 "fi; "                                                  \
 526         "else; "                                                        \
 527                 "echo DOWNLOAD FAILED; "                                \
 528         "fi;"
 529
 530 #define CONFIG_PROG_UBOOT2                                              \
 531         "$download_cmd $loadaddr $ubootfile; "                          \
 532         "if test $? -eq 0; then "                                       \
 533                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 534                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 535                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 536                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 537                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 538                 "if test $? -ne 0; then "                               \
 539                         "echo PROGRAM FAILED; "                         \
 540                 "else; "                                                \
 541                         "echo PROGRAM SUCCEEDED; "                      \
 542                 "fi; "                                                  \
 543         "else; "                                                        \
 544                 "echo DOWNLOAD FAILED; "                                \
 545         "fi;"
 546
 547 #define CONFIG_BOOT_OS_NET                                              \
 548         "$download_cmd $osaddr $osfile; "                               \
 549         "if test $? -eq 0; then "                                       \
 550                 "if test -n $fdtaddr; then "                            \
 551                         "$download_cmd $fdtaddr $fdtfile; "             \
 552                         "if test $? -eq 0; then "                       \
 553                                 "bootm $osaddr - $fdtaddr; "            \
 554                         "else; "                                        \
 555                                 "echo FDT DOWNLOAD FAILED; "            \
 556                         "fi; "                                          \
 557                 "else; "                                                \
 558                         "bootm $osaddr; "                               \
 559                 "fi; "                                                  \
 560         "else; "                                                        \
 561                 "echo OS DOWNLOAD FAILED; "                             \
 562         "fi;"
 563
 564 #define CONFIG_PROG_OS1                                                 \
 565         "$download_cmd $osaddr $osfile; "                               \
 566         "if test $? -eq 0; then "                                       \
 567                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 568                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 569                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 570                 "if test $? -ne 0; then "                               \
 571                         "echo OS PROGRAM FAILED; "                      \
 572                 "else; "                                                \
 573                         "echo OS PROGRAM SUCCEEDED; "                   \
 574                 "fi; "                                                  \
 575         "else; "                                                        \
 576                 "echo OS DOWNLOAD FAILED; "                             \
 577         "fi;"
 578
 579 #define CONFIG_PROG_OS2                                                 \
 580         "$download_cmd $osaddr $osfile; "                               \
 581         "if test $? -eq 0; then "                                       \
 582                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 583                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 584                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 585                 "if test $? -ne 0; then "                               \
 586                         "echo OS PROGRAM FAILED; "                      \
 587                 "else; "                                                \
 588                         "echo OS PROGRAM SUCCEEDED; "                   \
 589                 "fi; "                                                  \
 590         "else; "                                                        \
 591                 "echo OS DOWNLOAD FAILED; "                             \
 592         "fi;"
 593
 594 #define CONFIG_PROG_FDT1                                                \
 595         "$download_cmd $fdtaddr $fdtfile; "                             \
 596         "if test $? -eq 0; then "                                       \
 597                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 598                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 599                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 600                 "if test $? -ne 0; then "                               \
 601                         "echo FDT PROGRAM FAILED; "                     \
 602                 "else; "                                                \
 603                         "echo FDT PROGRAM SUCCEEDED; "                  \
 604                 "fi; "                                                  \
 605         "else; "                                                        \
 606                 "echo FDT DOWNLOAD FAILED; "                            \
 607         "fi;"
 608
 609 #define CONFIG_PROG_FDT2                                                \
 610         "$download_cmd $fdtaddr $fdtfile; "                             \
 611         "if test $? -eq 0; then "                                       \
 612                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 613                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 614                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 615                 "if test $? -ne 0; then "                               \
 616                         "echo FDT PROGRAM FAILED; "                     \
 617                 "else; "                                                \
 618                         "echo FDT PROGRAM SUCCEEDED; "                  \
 619                 "fi; "                                                  \
 620         "else; "                                                        \
 621                 "echo FDT DOWNLOAD FAILED; "                            \
 622         "fi;"
 623
 624 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 625         "autoload=yes\0"                                                \
 626         "download_cmd=tftp\0"                                           \
 627         "console_args=console=ttyS0,115200\0"                           \
 628         "root_args=root=/dev/nfs rw\0"                                  \
 629         "misc_args=ip=on\0"                                             \
 630         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 631         "bootfile=/home/user/file\0"                                    \
 632         "osfile=/home/user/board.uImage\0"                              \
 633         "fdtfile=/home/user/board.dtb\0"                                \
 634         "ubootfile=/home/user/u-boot.bin\0"                             \
 635         "fdtaddr=0x1e00000\0"                                           \
 636         "osaddr=0x1000000\0"                                            \
 637         "loadaddr=0x1000000\0"                                          \
 638         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 639         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 640         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 641         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 642         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 643         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 644         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 645         "bootcmd_flash1=run set_bootargs; "                             \
 646                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 647         "bootcmd_flash2=run set_bootargs; "                             \
 648                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 649         "bootcmd=run bootcmd_flash1\0"
 650 #endif  /* __CONFIG_H */