include/configs/xpedite517x.h

   1 /*
   2  * Copyright 2009 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * xpedite517x board configuration file
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_SYS_BOARD_NAME   "XPedite5170"
  18 #define CONFIG_SYS_FORM_3U_VPX  1
  19 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  20 #define CONFIG_BOARD_EARLY_INIT_R       /* Call board_pre_init */
  21 #define CONFIG_BAT_RW           1       /* Use common BAT rw code */
  22 #define CONFIG_HIGH_BATS        1       /* High BATs supported and enabled */
  23 #define CONFIG_ALTIVEC          1
  24
  25 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  26 #define CONFIG_PCIE1            1       /* PCIE controller 1 */
  27 #define CONFIG_PCIE2            1       /* PCIE controller 2 */
  28 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  29 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  30 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  31
  32 /*
  33  * DDR config
  34  */
  35 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  36 #define CONFIG_DDR_SPD
  37 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  38 #define SPD_EEPROM_ADDRESS1             0x54    /* Both channels use the */
  39 #define SPD_EEPROM_ADDRESS2             0x54    /* same SPD data         */
  40 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  41 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  42 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  43 #define CONFIG_DDR_ECC
  44 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  45 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
  46 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  47 #define CONFIG_VERY_BIG_RAM
  48 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
  49
  50 /*
  51  * virtual address to be used for temporary mappings.  There
  52  * should be 128k free at this VA.
  53  */
  54 #define CONFIG_SYS_SCRATCH_VA   0xe0000000
  55
  56 #ifndef __ASSEMBLY__
  57 extern unsigned long get_board_sys_clk(unsigned long dummy);
  58 #endif
  59
  60 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC86xx */
  61
  62 /*
  63  * L2CR setup
  64  */
  65 #define CONFIG_SYS_L2
  66 #define L2_INIT         0
  67 #define L2_ENABLE       (L2CR_L2E)
  68
  69 /*
  70  * Base addresses -- Note these are effective addresses where the
  71  * actual resources get mapped (not physical addresses)
  72  */
  73 #define CONFIG_SYS_CCSRBAR              0xef000000      /* relocated CCSRBAR */
  74 #define CONFIG_SYS_CCSRBAR_PHYS         CONFIG_SYS_CCSRBAR
  75 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  76 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    0x0
  77 #define CONFIG_SYS_IMMR                 CONFIG_SYS_CCSRBAR
  78
  79 /*
  80  * Diagnostics
  81  */
  82 #define CONFIG_SYS_ALT_MEMTEST
  83 #define CONFIG_SYS_MEMTEST_START        0x10000000
  84 #define CONFIG_SYS_MEMTEST_END          0x20000000
  85 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY |\
  86                                          CONFIG_SYS_POST_I2C)
  87 /* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
  88 #define I2C_ADDR_IGNORE_LIST            {0x50}
  89
  90 /*
  91  * Memory map
  92  * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
  93  * 0x8000_0000  0xbfff_ffff     PCIe1 Mem               1G non-cacheable
  94  * 0xc000_0000  0xcfff_ffff     PCIe2 Mem               256M non-cacheable
  95  * 0xe000_0000  0xe7ff_ffff     SRAM/SSRAM/L1 Cache     128M non-cacheable
  96  * 0xe800_0000  0xe87f_ffff     PCIe1 IO                8M non-cacheable
  97  * 0xe880_0000  0xe8ff_ffff     PCIe2 IO                8M non-cacheable
  98  * 0xef00_0000  0xef0f_ffff     CCSR/IMMR               1M non-cacheable
  99  * 0xef80_0000  0xef8f_ffff     NAND Flash              1M non-cacheable
 100  * 0xf000_0000  0xf7ff_ffff     NOR Flash 2             128M non-cacheable
 101  * 0xf800_0000  0xffff_ffff     NOR Flash 1             128M non-cacheable
 102  */
 103
 104 #define CONFIG_SYS_LBC_LCRR             (LCRR_CLKDIV_4 | LCRR_EADC_3)
 105
 106 /*
 107  * NAND flash configuration
 108  */
 109 #define CONFIG_SYS_NAND_BASE            0xef800000
 110 #define CONFIG_SYS_NAND_BASE2           0xef840000      /* Unused at this time */
 111 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
 112 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 113 #define CONFIG_NAND_ACTL
 114 #define CONFIG_SYS_NAND_ACTL_ALE        (1 << 14)       /* C_LA14 */
 115 #define CONFIG_SYS_NAND_ACTL_CLE        (1 << 15)       /* C_LA15 */
 116 #define CONFIG_SYS_NAND_ACTL_NCE        0               /* NCE not controlled by ADDR */
 117 #define CONFIG_SYS_NAND_ACTL_DELAY      25
 118 #define CONFIG_JFFS2_NAND
 119
 120 /*
 121  * NOR flash configuration
 122  */
 123 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 124 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 125 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 126 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 127 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 128 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 129 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 130 #define CONFIG_FLASH_CFI_DRIVER
 131 #define CONFIG_SYS_FLASH_CFI
 132 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 133 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff00000, 0xc0000}, \
 134                                                   {0xf7f00000, 0xc0000} }
 135 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 136 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 137
 138 /*
 139  * Chip select configuration
 140  */
 141 /* NOR Flash 0 on CS0 */
 142 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  |\
 143                                  BR_PS_16               |\
 144                                  BR_V)
 145 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            |\
 146                                  OR_GPCM_CSNT           |\
 147                                  OR_GPCM_XACS           |\
 148                                  OR_GPCM_ACS_DIV2       |\
 149                                  OR_GPCM_SCY_8          |\
 150                                  OR_GPCM_TRLX           |\
 151                                  OR_GPCM_EHTR           |\
 152                                  OR_GPCM_EAD)
 153
 154 /* NOR Flash 1 on CS1 */
 155 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 |\
 156                                  BR_PS_16               |\
 157                                  BR_V)
 158 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 159
 160 /* NAND flash on CS2 */
 161 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   |\
 162                                  BR_PS_8                |\
 163                                  BR_V)
 164 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB            |\
 165                                  OR_GPCM_BCTLD          |\
 166                                  OR_GPCM_CSNT           |\
 167                                  OR_GPCM_ACS_DIV4       |\
 168                                  OR_GPCM_SCY_4          |\
 169                                  OR_GPCM_TRLX           |\
 170                                  OR_GPCM_EHTR)
 171
 172 /* Optional NAND flash on CS3 */
 173 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  |\
 174                                  BR_PS_8                |\
 175                                  BR_V)
 176 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 177
 178 /*
 179  * Use L1 as initial stack
 180  */
 181 #define CONFIG_SYS_INIT_RAM_LOCK        1
 182 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 183 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 184
 185 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 186 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 187
 188 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 189 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 190
 191 /*
 192  * Serial Port
 193  */
 194 #define CONFIG_SYS_NS16550_SERIAL
 195 #define CONFIG_SYS_NS16550_REG_SIZE     1
 196 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 197 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 198 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 199 #define CONFIG_SYS_BAUDRATE_TABLE       \
 200         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 201 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 202 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 203
 204 /*
 205  * I2C
 206  */
 207 #define CONFIG_SYS_I2C
 208 #define CONFIG_SYS_I2C_FSL
 209 #define CONFIG_SYS_FSL_I2C_SPEED        100000
 210 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 211 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 212 #define CONFIG_SYS_FSL_I2C2_SPEED       100000
 213 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 214 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 215
 216 /* PEX8518 slave I2C interface */
 217 #define CONFIG_SYS_I2C_PEX8518_ADDR     0x70
 218
 219 /* I2C DS1631 temperature sensor */
 220 #define CONFIG_SYS_I2C_LM90_ADDR        0x4c
 221
 222 /* I2C EEPROM - AT24C128B */
 223 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 224 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 225 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 226 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 227
 228 /* I2C RTC */
 229 #define CONFIG_RTC_M41T11               1
 230 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 231 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 232
 233 /* GPIO */
 234 #define CONFIG_PCA953X
 235 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 236 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 237 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 238 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 239 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 240 #define CONFIG_SYS_I2C_PCA9553_ADDR     0x62
 241
 242 /*
 243  * PU = pulled high, PD = pulled low
 244  * I = input, O = output, IO = input/output
 245  */
 246 /* PCA9557 @ 0x18*/
 247 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 248 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select */
 249 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 250 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select */
 251 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 252 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Set to 0 to enable NVM writing */
 253
 254 /* PCA9557 @ 0x1c*/
 255 #define CONFIG_SYS_PCA953X_XMC0_ROOT0           0x01 /* PU; Low if XMC is RC */
 256 #define CONFIG_SYS_PCA953X_PLUG_GPIO0           0x02 /* Samtec connector GPIO */
 257 #define CONFIG_SYS_PCA953X_XMC0_WAKE            0x04 /* PU; XMC wake */
 258 #define CONFIG_SYS_PCA953X_XMC0_BIST            0x08 /* PU; XMC built in self test */
 259 #define CONFIG_SYS_PCA953X_XMC_PRESENT          0x10 /* PU; Low if XMC module installed */
 260 #define CONFIG_SYS_PCA953X_PMC_PRESENT          0x20 /* PU; Low if PMC module installed */
 261 #define CONFIG_SYS_PCA953X_PMC0_MONARCH         0x40 /* PMC monarch mode enable */
 262 #define CONFIG_SYS_PCA953X_PMC0_EREADY          0x80 /* PU; PMC PCI eready */
 263
 264 /* PCA9557 @ 0x1e*/
 265 #define CONFIG_SYS_PCA953X_P0_GA0               0x01 /* PU; VPX Geographical address */
 266 #define CONFIG_SYS_PCA953X_P0_GA1               0x02 /* PU; VPX Geographical address */
 267 #define CONFIG_SYS_PCA953X_P0_GA2               0x04 /* PU; VPX Geographical address */
 268 #define CONFIG_SYS_PCA953X_P0_GA3               0x08 /* PU; VPX Geographical address */
 269 #define CONFIG_SYS_PCA953X_P0_GA4               0x10 /* PU; VPX Geographical address */
 270 #define CONFIG_SYS_PCA953X_P0_GAP               0x20 /* PU; VPX Geographical address parity */
 271 #define CONFIG_SYS_PCA953X_P1_SYSEN             0x80 /* PU; VPX P1 SYSCON */
 272
 273 /* PCA9557 @ 0x1f */
 274 #define CONFIG_SYS_PCA953X_VPX_GPIO0            0x01 /* PU; VPX P15 GPIO */
 275 #define CONFIG_SYS_PCA953X_VPX_GPIO1            0x02 /* PU; VPX P15 GPIO */
 276 #define CONFIG_SYS_PCA953X_VPX_GPIO2            0x04 /* PU; VPX P15 GPIO */
 277 #define CONFIG_SYS_PCA953X_VPX_GPIO3            0x08 /* PU; VPX P15 GPIO */
 278
 279 /*
 280  * General PCI
 281  * Memory space is mapped 1-1, but I/O space must start from 0.
 282  */
 283 /* PCIE1 - PEX8518 */
 284 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 285 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 286 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 287 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 288 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 289 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 290
 291 /* PCIE2 - VPX P1 */
 292 #define CONFIG_SYS_PCIE2_MEM_BUS        0xc0000000
 293 #define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
 294 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
 295 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 296 #define CONFIG_SYS_PCIE2_IO_PHYS        0xe8800000
 297 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000      /* 8M */
 298
 299 /*
 300  * Networking options
 301  */
 302 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
 303 #define CONFIG_MII              1       /* MII PHY management */
 304 #define CONFIG_ETHPRIME         "eTSEC1"
 305
 306 #define CONFIG_TSEC1            1
 307 #define CONFIG_TSEC1_NAME       "eTSEC1"
 308 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 309 #define TSEC1_PHY_ADDR          1
 310 #define TSEC1_PHYIDX            0
 311 #define CONFIG_HAS_ETH0
 312
 313 #define CONFIG_TSEC2            1
 314 #define CONFIG_TSEC2_NAME       "eTSEC2"
 315 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 316 #define TSEC2_PHY_ADDR          2
 317 #define TSEC2_PHYIDX            0
 318 #define CONFIG_HAS_ETH1
 319
 320 /*
 321  * BAT mappings
 322  */
 323 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 324 #define CONFIG_SYS_CCSR_DEFAULT_DBATL   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 325                                          BATL_PP_RW                     |\
 326                                          BATL_CACHEINHIBIT              |\
 327                                          BATL_GUARDEDSTORAGE)
 328 #define CONFIG_SYS_CCSR_DEFAULT_DBATU   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 329                                          BATU_BL_1M                     |\
 330                                          BATU_VS                        |\
 331                                          BATU_VP)
 332 #define CONFIG_SYS_CCSR_DEFAULT_IBATL   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 333                                          BATL_PP_RW                     |\
 334                                          BATL_CACHEINHIBIT)
 335 #define CONFIG_SYS_CCSR_DEFAULT_IBATU   CONFIG_SYS_CCSR_DEFAULT_DBATU
 336 #endif
 337
 338 /*
 339  * BAT0         2G      Cacheable, non-guarded
 340  * 0x0000_0000  2G      DDR
 341  */
 342 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 343 #define CONFIG_SYS_DBAT0U       (BATU_BL_2G | BATU_VS | BATU_VP)
 344 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 345 #define CONFIG_SYS_IBAT0U       CONFIG_SYS_DBAT0U
 346
 347 /*
 348  * BAT1         1G      Cache-inhibited, guarded
 349  * 0x8000_0000  1G      PCI-Express 1 Memory
 350  */
 351 #define CONFIG_SYS_DBAT1L       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 352                                  BATL_PP_RW                     |\
 353                                  BATL_CACHEINHIBIT              |\
 354                                  BATL_GUARDEDSTORAGE)
 355 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 356                                  BATU_BL_1G                     |\
 357                                  BATU_VS                        |\
 358                                  BATU_VP)
 359 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 360                                  BATL_PP_RW                     |\
 361                                  BATL_CACHEINHIBIT)
 362 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 363
 364 /*
 365  * BAT2         512M    Cache-inhibited, guarded
 366  * 0xc000_0000  512M    PCI-Express 2 Memory
 367  */
 368 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 369                                  BATL_PP_RW                     |\
 370                                  BATL_CACHEINHIBIT              |\
 371                                  BATL_GUARDEDSTORAGE)
 372 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 373                                  BATU_BL_512M                   |\
 374                                  BATU_VS                        |\
 375                                  BATU_VP)
 376 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 377                                  BATL_PP_RW                     |\
 378                                  BATL_CACHEINHIBIT)
 379 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 380
 381 /*
 382  * BAT3         1M      Cache-inhibited, guarded
 383  * 0xe000_0000  1M      CCSR
 384  */
 385 #define CONFIG_SYS_DBAT3L       (CONFIG_SYS_CCSRBAR             |\
 386                                  BATL_PP_RW                     |\
 387                                  BATL_CACHEINHIBIT              |\
 388                                  BATL_GUARDEDSTORAGE)
 389 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR             |\
 390                                  BATU_BL_1M                     |\
 391                                  BATU_VS                        |\
 392                                  BATU_VP)
 393 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_CCSRBAR             |\
 394                                  BATL_PP_RW                     |\
 395                                  BATL_CACHEINHIBIT)
 396 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 397
 398 /*
 399  * BAT4         32M     Cache-inhibited, guarded
 400  * 0xe200_0000  16M     PCI-Express 1 I/O
 401  * 0xe300_0000  16M     PCI-Express 2 I/0
 402  */
 403 #define CONFIG_SYS_DBAT4L       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 404                                  BATL_PP_RW                     |\
 405                                  BATL_CACHEINHIBIT              |\
 406                                  BATL_GUARDEDSTORAGE)
 407 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 408                                  BATU_BL_32M                    |\
 409                                  BATU_VS                        |\
 410                                  BATU_VP)
 411 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 412                                  BATL_PP_RW                     |\
 413                                  BATL_CACHEINHIBIT)
 414 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 415
 416 /*
 417  * BAT5         128K    Cacheable, non-guarded
 418  * 0xe400_1000  128K    Init RAM for stack in the CPU DCache (no backing memory)
 419  */
 420 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR       |\
 421                                  BATL_PP_RW                     |\
 422                                  BATL_MEMCOHERENCE)
 423 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR       |\
 424                                  BATU_BL_128K                   |\
 425                                  BATU_VS                        |\
 426                                  BATU_VP)
 427 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 428 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 429
 430 /*
 431  * BAT6         256M    Cache-inhibited, guarded
 432  * 0xf000_0000  256M    FLASH
 433  */
 434 #define CONFIG_SYS_DBAT6L       (CONFIG_SYS_FLASH_BASE2         |\
 435                                  BATL_PP_RW                     |\
 436                                  BATL_CACHEINHIBIT              |\
 437                                  BATL_GUARDEDSTORAGE)
 438 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE          |\
 439                                  BATU_BL_256M                   |\
 440                                  BATU_VS                        |\
 441                                  BATU_VP)
 442 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_FLASH_BASE          |\
 443                                  BATL_PP_RW                     |\
 444                                  BATL_MEMCOHERENCE)
 445 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 446
 447 /* Map the last 1M of flash where we're running from reset */
 448 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY  |\
 449                                  BATL_PP_RW                     |\
 450                                  BATL_CACHEINHIBIT              |\
 451                                  BATL_GUARDEDSTORAGE)
 452 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE                   |\
 453                                  BATU_BL_1M                     |\
 454                                  BATU_VS                        |\
 455                                  BATU_VP)
 456 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY  |\
 457                                  BATL_PP_RW                     |\
 458                                  BATL_MEMCOHERENCE)
 459 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 460
 461 /*
 462  * BAT7         64M     Cache-inhibited, guarded
 463  * 0xe800_0000  64K     NAND FLASH
 464  * 0xe804_0000  128K    DUART Registers
 465  */
 466 #define CONFIG_SYS_DBAT7L       (CONFIG_SYS_NAND_BASE           |\
 467                                  BATL_PP_RW                     |\
 468                                  BATL_CACHEINHIBIT              |\
 469                                  BATL_GUARDEDSTORAGE)
 470 #define CONFIG_SYS_DBAT7U       (CONFIG_SYS_NAND_BASE           |\
 471                                  BATU_BL_512K                   |\
 472                                  BATU_VS                        |\
 473                                  BATU_VP)
 474 #define CONFIG_SYS_IBAT7L       (CONFIG_SYS_NAND_BASE           |\
 475                                  BATL_PP_RW                     |\
 476                                  BATL_CACHEINHIBIT)
 477 #define CONFIG_SYS_IBAT7U       CONFIG_SYS_DBAT7U
 478
 479 /*
 480  * Miscellaneous configurable options
 481  */
 482 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 483 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 484 #define CONFIG_PREBOOT                          /* enable preboot variable */
 485 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 486
 487 /*
 488  * For booting Linux, the board info and command line data
 489  * have to be in the first 16 MB of memory, since this is
 490  * the maximum mapped by the Linux kernel during initialization.
 491  */
 492 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 493 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 494
 495 /*
 496  * Environment Configuration
 497  */
 498 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 499 #define CONFIG_ENV_SIZE         0x8000
 500 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 501
 502 /*
 503  * Flash memory map:
 504  * fffc0000 - ffffffff  Pri FDT (256KB)
 505  * fff80000 - fffbffff  Pri U-Boot Environment (256 KB)
 506  * fff00000 - fff7ffff  Pri U-Boot (512 KB)
 507  * fef00000 - ffefffff  Pri OS image (16MB)
 508  * f8000000 - feefffff  Pri OS Use/Filesystem (111MB)
 509  *
 510  * f7fc0000 - f7ffffff  Sec FDT (256KB)
 511  * f7f80000 - f7fbffff  Sec U-Boot Environment (256 KB)
 512  * f7f00000 - f7f7ffff  Sec U-Boot (512 KB)
 513  * f6f00000 - f7efffff  Sec OS image (16MB)
 514  * f0000000 - f6efffff  Sec OS Use/Filesystem (111MB)
 515  */
 516 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff00000)
 517 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f00000)
 518 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfffc0000)
 519 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7fc0000)
 520 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 521 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 522
 523 #define CONFIG_PROG_UBOOT1                                              \
 524         "$download_cmd $loadaddr $ubootfile; "                          \
 525         "if test $? -eq 0; then "                                       \
 526                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 527                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 528                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 529                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 530                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 531                 "if test $? -ne 0; then "                               \
 532                         "echo PROGRAM FAILED; "                         \
 533                 "else; "                                                \
 534                         "echo PROGRAM SUCCEEDED; "                      \
 535                 "fi; "                                                  \
 536         "else; "                                                        \
 537                 "echo DOWNLOAD FAILED; "                                \
 538         "fi;"
 539
 540 #define CONFIG_PROG_UBOOT2                                              \
 541         "$download_cmd $loadaddr $ubootfile; "                          \
 542         "if test $? -eq 0; then "                                       \
 543                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 544                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 545                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 546                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 547                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 548                 "if test $? -ne 0; then "                               \
 549                         "echo PROGRAM FAILED; "                         \
 550                 "else; "                                                \
 551                         "echo PROGRAM SUCCEEDED; "                      \
 552                 "fi; "                                                  \
 553         "else; "                                                        \
 554                 "echo DOWNLOAD FAILED; "                                \
 555         "fi;"
 556
 557 #define CONFIG_BOOT_OS_NET                                              \
 558         "$download_cmd $osaddr $osfile; "                               \
 559         "if test $? -eq 0; then "                                       \
 560                 "if test -n $fdtaddr; then "                            \
 561                         "$download_cmd $fdtaddr $fdtfile; "             \
 562                         "if test $? -eq 0; then "                       \
 563                                 "bootm $osaddr - $fdtaddr; "            \
 564                         "else; "                                        \
 565                                 "echo FDT DOWNLOAD FAILED; "            \
 566                         "fi; "                                          \
 567                 "else; "                                                \
 568                         "bootm $osaddr; "                               \
 569                 "fi; "                                                  \
 570         "else; "                                                        \
 571                 "echo OS DOWNLOAD FAILED; "                             \
 572         "fi;"
 573
 574 #define CONFIG_PROG_OS1                                                 \
 575         "$download_cmd $osaddr $osfile; "                               \
 576         "if test $? -eq 0; then "                                       \
 577                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 578                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 579                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 580                 "if test $? -ne 0; then "                               \
 581                         "echo OS PROGRAM FAILED; "                      \
 582                 "else; "                                                \
 583                         "echo OS PROGRAM SUCCEEDED; "                   \
 584                 "fi; "                                                  \
 585         "else; "                                                        \
 586                 "echo OS DOWNLOAD FAILED; "                             \
 587         "fi;"
 588
 589 #define CONFIG_PROG_OS2                                                 \
 590         "$download_cmd $osaddr $osfile; "                               \
 591         "if test $? -eq 0; then "                                       \
 592                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 593                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 594                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 595                 "if test $? -ne 0; then "                               \
 596                         "echo OS PROGRAM FAILED; "                      \
 597                 "else; "                                                \
 598                         "echo OS PROGRAM SUCCEEDED; "                   \
 599                 "fi; "                                                  \
 600         "else; "                                                        \
 601                 "echo OS DOWNLOAD FAILED; "                             \
 602         "fi;"
 603
 604 #define CONFIG_PROG_FDT1                                                \
 605         "$download_cmd $fdtaddr $fdtfile; "                             \
 606         "if test $? -eq 0; then "                                       \
 607                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 608                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 609                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 610                 "if test $? -ne 0; then "                               \
 611                         "echo FDT PROGRAM FAILED; "                     \
 612                 "else; "                                                \
 613                         "echo FDT PROGRAM SUCCEEDED; "                  \
 614                 "fi; "                                                  \
 615         "else; "                                                        \
 616                 "echo FDT DOWNLOAD FAILED; "                            \
 617         "fi;"
 618
 619 #define CONFIG_PROG_FDT2                                                \
 620         "$download_cmd $fdtaddr $fdtfile; "                             \
 621         "if test $? -eq 0; then "                                       \
 622                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 623                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 624                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 625                 "if test $? -ne 0; then "                               \
 626                         "echo FDT PROGRAM FAILED; "                     \
 627                 "else; "                                                \
 628                         "echo FDT PROGRAM SUCCEEDED; "                  \
 629                 "fi; "                                                  \
 630         "else; "                                                        \
 631                 "echo FDT DOWNLOAD FAILED; "                            \
 632         "fi;"
 633
 634 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 635         "autoload=yes\0"                                                \
 636         "download_cmd=tftp\0"                                           \
 637         "console_args=console=ttyS0,115200\0"                           \
 638         "root_args=root=/dev/nfs rw\0"                                  \
 639         "misc_args=ip=on\0"                                             \
 640         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 641         "bootfile=/home/user/file\0"                                    \
 642         "osfile=/home/user/board.uImage\0"                              \
 643         "fdtfile=/home/user/board.dtb\0"                                \
 644         "ubootfile=/home/user/u-boot.bin\0"                             \
 645         "fdtaddr=0x1e00000\0"                                           \
 646         "osaddr=0x1000000\0"                                            \
 647         "loadaddr=0x1000000\0"                                          \
 648         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 649         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 650         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 651         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 652         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 653         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 654         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 655         "bootcmd_flash1=run set_bootargs; "                             \
 656                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 657         "bootcmd_flash2=run set_bootargs; "                             \
 658                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 659         "bootcmd=run bootcmd_flash1\0"
 660 #endif  /* __CONFIG_H */