include/configs/woodburn_common.h

   1 /*
   2  * (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
   3  *
   4  * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
   5  *
   6  * Configuration for the woodburn board.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __WOODBURN_COMMON_CONFIG_H
  12 #define __WOODBURN_COMMON_CONFIG_H
  13
  14 #include <asm/arch/imx-regs.h>
  15
  16  /* High Level Configuration Options */
  17 #define CONFIG_MX35
  18 #define CONFIG_MX35_HCLK_FREQ   24000000
  19 #define CONFIG_SYS_FSL_CLK
  20
  21 #define CONFIG_SYS_DCACHE_OFF
  22
  23 /* Only in case the value is not present in mach-types.h */
  24 #ifndef MACH_TYPE_FLEA3
  25 #define MACH_TYPE_FLEA3                3668
  26 #endif
  27
  28 #define CONFIG_MACH_TYPE                MACH_TYPE_FLEA3
  29
  30 /* This is required to setup the ESDC controller */
  31
  32 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
  33 #define CONFIG_REVISION_TAG
  34 #define CONFIG_SETUP_MEMORY_TAGS
  35 #define CONFIG_INITRD_TAG
  36
  37 /*
  38  * Size of malloc() pool
  39  */
  40 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  41
  42 /*
  43  * Hardware drivers
  44  */
  45 #define CONFIG_SYS_I2C
  46 #define CONFIG_SYS_I2C_MXC
  47 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  48 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  49 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  50 #define CONFIG_SYS_SPD_BUS_NUM          0
  51 #define CONFIG_MXC_SPI
  52 #define CONFIG_MXC_GPIO
  53
  54 /* PMIC Controller */
  55 #define CONFIG_POWER
  56 #define CONFIG_POWER_I2C
  57 #define CONFIG_POWER_FSL
  58 #define CONFIG_POWER_FSL_MC13892
  59 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR    0x8
  60 #define CONFIG_RTC_MC13XXX
  61
  62 /* mmc driver */
  63 #define CONFIG_GENERIC_MMC
  64 #define CONFIG_FSL_ESDHC
  65 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  66 #define CONFIG_SYS_FSL_ESDHC_NUM        1
  67
  68 /*
  69  * UART (console)
  70  */
  71 #define CONFIG_MXC_UART
  72 #define CONFIG_MXC_UART_BASE    UART1_BASE
  73
  74 /* allow to overwrite serial and ethaddr */
  75 #define CONFIG_ENV_OVERWRITE
  76 #define CONFIG_CONS_INDEX       1
  77 #define CONFIG_BAUDRATE         115200
  78
  79 /*
  80  * Command definition
  81  */
  82 #define CONFIG_CMD_DATE
  83 #define CONFIG_BOOTP_SUBNETMASK
  84 #define CONFIG_BOOTP_GATEWAY
  85 #define CONFIG_BOOTP_DNS
  86
  87 #define CONFIG_CMD_NAND
  88
  89 #define CONFIG_MXC_GPIO
  90
  91 #define CONFIG_NET_RETRY_COUNT  100
  92
  93
  94 #define CONFIG_LOADADDR         0x80800000      /* loadaddr env var */
  95
  96 /*
  97  * Ethernet on SOC (FEC)
  98  */
  99 #define CONFIG_FEC_MXC
 100 #define IMX_FEC_BASE    FEC_BASE_ADDR
 101 #define CONFIG_PHYLIB
 102 #define CONFIG_PHY_MICREL
 103 #define CONFIG_FEC_MXC_PHYADDR  0x1
 104
 105 #define CONFIG_MII
 106 #define CONFIG_DISCOVER_PHY
 107
 108 #define CONFIG_ARP_TIMEOUT      200UL
 109
 110 /*
 111  * Miscellaneous configurable options
 112  */
 113 #define CONFIG_SYS_LONGHELP     /* undef to save memory */
 114 #define CONFIG_CMDLINE_EDITING
 115
 116 #define CONFIG_AUTO_COMPLETE
 117 #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
 118 /* Print Buffer Size */
 119 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 120 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 121 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 122
 123 #define CONFIG_SYS_MEMTEST_START        0       /* memtest works on */
 124 #define CONFIG_SYS_MEMTEST_END          0x10000
 125
 126 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 127
 128 /*
 129  * Stack sizes
 130  *
 131  * The stack sizes are set up in start.S using the settings below
 132  */
 133 #define CONFIG_STACKSIZE        (128 * 1024)    /* regular stack */
 134
 135 /*
 136  * Physical Memory Map
 137  */
 138 #define CONFIG_NR_DRAM_BANKS    1
 139 #define PHYS_SDRAM_1            CSD0_BASE_ADDR
 140 #define PHYS_SDRAM_1_SIZE       (256 * 1024 * 1024)
 141
 142 #define CONFIG_SYS_SDRAM_BASE           CSD0_BASE_ADDR
 143
 144 #define CONFIG_SYS_GBL_DATA_OFFSET      (LOW_LEVEL_SRAM_STACK - \
 145                                                 IRAM_BASE_ADDR - \
 146                                                 GENERATED_GBL_DATA_SIZE)
 147 #define CONFIG_SYS_INIT_SP_ADDR         (IRAM_BASE_ADDR + \
 148                                         CONFIG_SYS_GBL_DATA_OFFSET)
 149
 150 /*
 151  * MTD Command for mtdparts
 152  */
 153 #define CONFIG_CMD_MTDPARTS
 154 #define CONFIG_MTD_DEVICE
 155 #define CONFIG_FLASH_CFI_MTD
 156 #define CONFIG_MTD_PARTITIONS
 157 #define MTDIDS_DEFAULT          "nand0=mxc_nand,nor0=physmap-flash.0"
 158 #define MTDPARTS_DEFAULT        "mtdparts=mxc_nand:50m(root1)," \
 159                                 "32m(rootfb)," \
 160                                 "64m(pcache)," \
 161                                 "64m(app1)," \
 162                                 "10m(app2),-(spool);" \
 163                                 "physmap-flash.0:512k(u-boot),64k(env1)," \
 164                                 "64k(env2),3776k(kernel1),3776k(kernel2)"
 165
 166 /*
 167  * FLASH and environment organization
 168  */
 169 #define CONFIG_SYS_FLASH_BASE           CS0_BASE_ADDR
 170 #define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
 171 #define CONFIG_SYS_MAX_FLASH_SECT 512   /* max number of sectors on one chip */
 172 /* Monitor at beginning of flash */
 173 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 174 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
 175
 176 #define CONFIG_ENV_SECT_SIZE    (128 * 1024)
 177 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 178
 179 /* Address and size of Redundant Environment Sector     */
 180 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 181 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 182
 183 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 184                                 CONFIG_SYS_MONITOR_LEN)
 185
 186 #define CONFIG_ENV_IS_IN_FLASH
 187
 188 /*
 189  * CFI FLASH driver setup
 190  */
 191 #define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
 192 #define CONFIG_FLASH_CFI_DRIVER
 193
 194 /* A non-standard buffered write algorithm */
 195 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       /* faster */
 196 #define CONFIG_SYS_FLASH_PROTECTION     /* Use hardware sector protection */
 197
 198 /*
 199  * NAND FLASH driver setup
 200  */
 201 #define CONFIG_NAND_MXC
 202 #define CONFIG_NAND_MXC_V1_1
 203 #define CONFIG_MXC_NAND_REGS_BASE       (NFC_BASE_ADDR)
 204 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 205 #define CONFIG_SYS_NAND_BASE            (NFC_BASE_ADDR)
 206 #define CONFIG_MXC_NAND_HWECC
 207 #define CONFIG_SYS_NAND_LARGEPAGE
 208
 209 #if 0
 210 #define CONFIG_MTD_DEBUG
 211 #define CONFIG_MTD_DEBUG_VERBOSE        7
 212 #endif
 213 #define CONFIG_SYS_NAND_ONFI_DETECTION
 214
 215 /*
 216  * Default environment and default scripts
 217  * to update uboot and load kernel
 218  */
 219
 220 #define CONFIG_HOSTNAME woodburn
 221 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 222         "netdev=eth0\0"                                                 \
 223         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 224                 "nfsroot=${serverip}:${rootpath}\0"                     \
 225         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 226         "addip_sta=setenv bootargs ${bootargs} "                        \
 227                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 228                 ":${hostname}:${netdev}:off panic=1\0"                  \
 229         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 230         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
 231                 "else run addip_sta;fi\0"       \
 232         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 233         "addtty=setenv bootargs ${bootargs}"                            \
 234                 " console=ttymxc0,${baudrate}\0"                        \
 235         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
 236         "loadaddr=80800000\0"                                           \
 237         "kernel_addr_r=80800000\0"                                      \
 238         "hostname=" __stringify(CONFIG_HOSTNAME) "\0"                   \
 239         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"            \
 240         "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0"      \
 241         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 242                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 243         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 244                 "bootm ${kernel_addr}\0"                                \
 245         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 246                 "run nfsargs addip addtty addmtd addmisc;"              \
 247                 "bootm ${kernel_addr_r}\0"                              \
 248         "net_self_load=tftp ${kernel_addr_r} ${bootfile};"              \
 249                 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0"             \
 250         "net_self=if run net_self_load;then "                           \
 251                 "run ramargs addip addtty addmtd addmisc;"              \
 252                 "bootm ${kernel_addr_r} ${ramdisk_addr_r};"             \
 253                 "else echo Images not loades;fi\0"                      \
 254         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"          \
 255         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 256         "uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"         \
 257         "update=protect off ${uboot_addr} +80000;"                      \
 258                 "erase ${uboot_addr} +80000;"                           \
 259                 "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"          \
 260         "upd=if run load;then echo Updating u-boot;if run update;"      \
 261                 "then echo U-Boot updated;"                             \
 262                         "else echo Error updating u-boot !;"            \
 263                         "echo Board without bootloader !!;"             \
 264                 "fi;"                                                   \
 265                 "else echo U-Boot not downloaded..exiting;fi\0"         \
 266         "bootcmd=run net_nfs\0"
 267
 268 #endif                          /* __CONFIG_H */