include/configs/wandboard.h

   1 /*
   2  * Copyright (C) 2013 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Wandboard.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 #include <config_distro_defaults.h>
  13 #include "mx6_common.h"
  14
  15 #define CONFIG_SPL_MMC_SUPPORT
  16 #include "imx6_spl.h"
  17
  18 #define MACH_TYPE_WANDBOARD             4412
  19 #define CONFIG_MACH_TYPE                MACH_TYPE_WANDBOARD
  20
  21 /* Size of malloc() pool */
  22 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  23
  24 #define CONFIG_BOARD_EARLY_INIT_F
  25 #define CONFIG_BOARD_LATE_INIT
  26
  27 #define CONFIG_MXC_UART
  28 #define CONFIG_MXC_UART_BASE            UART1_BASE
  29
  30 /* SATA Configs */
  31
  32 #define CONFIG_CMD_SATA
  33 #ifdef CONFIG_CMD_SATA
  34 #define CONFIG_DWC_AHSATA
  35 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  36 #define CONFIG_DWC_AHSATA_PORT_ID       0
  37 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  38 #define CONFIG_LBA48
  39 #define CONFIG_LIBATA
  40 #endif
  41
  42 /* Command definition */
  43 #define CONFIG_CMD_BMODE
  44
  45 #define CONFIG_SYS_MEMTEST_START        0x10000000
  46 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
  47
  48 /* I2C Configs */
  49 #define CONFIG_SYS_I2C
  50 #define CONFIG_SYS_I2C_MXC
  51 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  52 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  53 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  54 #define CONFIG_SYS_I2C_SPEED            100000
  55
  56 /* MMC Configuration */
  57 #define CONFIG_SYS_FSL_USDHC_NUM        2
  58 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  59
  60 /* USB Configs */
  61 #define CONFIG_USB_EHCI
  62 #define CONFIG_USB_EHCI_MX6
  63 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  64 #define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
  65 #define CONFIG_MXC_USB_FLAGS            0
  66
  67 /* Ethernet Configuration */
  68 #define CONFIG_FEC_MXC
  69 #define CONFIG_MII
  70 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  71 #define CONFIG_FEC_XCV_TYPE             RGMII
  72 #define CONFIG_ETHPRIME                 "FEC"
  73 #define CONFIG_FEC_MXC_PHYADDR          1
  74 #define CONFIG_PHYLIB
  75 #define CONFIG_PHY_ATHEROS
  76
  77 /* Framebuffer */
  78 #define CONFIG_VIDEO
  79 #define CONFIG_VIDEO_IPUV3
  80 #define CONFIG_CFB_CONSOLE
  81 #define CONFIG_VGA_AS_SINGLE_DEVICE
  82 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
  83 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
  84 #define CONFIG_VIDEO_BMP_RLE8
  85 #define CONFIG_SPLASH_SCREEN
  86 #define CONFIG_SPLASH_SCREEN_ALIGN
  87 #define CONFIG_BMP_16BPP
  88 #define CONFIG_VIDEO_LOGO
  89 #define CONFIG_VIDEO_BMP_LOGO
  90 #define CONFIG_IPUV3_CLK 260000000
  91 #define CONFIG_CMD_HDMIDETECT
  92 #define CONFIG_IMX_HDMI
  93 #define CONFIG_IMX_VIDEO_SKIP
  94
  95 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  96 #define CONFIG_EXTRA_ENV_SETTINGS \
  97         "console=ttymxc0,115200\0" \
  98         "splashpos=m,m\0" \
  99         "fdtfile=undefined\0" \
 100         "fdt_high=0xffffffff\0" \
 101         "initrd_high=0xffffffff\0" \
 102         "fdt_addr_r=0x18000000\0" \
 103         "fdt_addr=0x18000000\0" \
 104         "ip_dyn=yes\0" \
 105         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
 106         "update_sd_firmware_filename=u-boot.imx\0" \
 107         "update_sd_firmware=" \
 108                 "if test ${ip_dyn} = yes; then " \
 109                         "setenv get_cmd dhcp; " \
 110                 "else " \
 111                         "setenv get_cmd tftp; " \
 112                 "fi; " \
 113                 "if mmc dev ${mmcdev}; then "   \
 114                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 115                                 "setexpr fw_sz ${filesize} / 0x200; " \
 116                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 117                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 118                         "fi; "  \
 119                 "fi\0" \
 120         "videoargs=" \
 121                 "setenv nextcon 0; " \
 122                 "if hdmidet; then " \
 123                         "setenv bootargs ${bootargs} " \
 124                                 "video=mxcfb${nextcon}:dev=hdmi,1280x720M@60," \
 125                                         "if=RGB24; " \
 126                         "setenv fbmen fbmem=28M; " \
 127                         "setexpr nextcon ${nextcon} + 1; " \
 128                 "else " \
 129                         "echo - no HDMI monitor;" \
 130                 "fi; " \
 131                 "i2c dev 1; " \
 132                 "if i2c probe 0x10; then " \
 133                         "setenv bootargs ${bootargs} " \
 134                                 "video=mxcfb${nextcon}:dev=lcd,800x480@60," \
 135                                         "if=RGB666,bpp=32; " \
 136                         "if test 0 -eq ${nextcon}; then " \
 137                                 "setenv fbmem fbmem=10M; " \
 138                         "else " \
 139                                 "setenv fbmem ${fbmem},10M; " \
 140                         "fi; " \
 141                         "setexpr nextcon ${nextcon} + 1; " \
 142                 "else " \
 143                         "echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';" \
 144                 "fi; " \
 145                 "setenv bootargs ${bootargs} ${fbmem}\0" \
 146         "findfdt="\
 147                 "if test $board_name = C1 && test $board_rev = MX6Q ; then " \
 148                         "setenv fdtfile imx6q-wandboard.dtb; fi; " \
 149                 "if test $board_name = C1 && test $board_rev = MX6DL ; then " \
 150                         "setenv fdtfile imx6dl-wandboard.dtb; fi; " \
 151                 "if test $board_name = B1 && test $board_rev = MX6Q ; then " \
 152                         "setenv fdtfile imx6q-wandboard-revb1.dtb; fi; " \
 153                 "if test $board_name = B1 && test $board_rev = MX6DL ; then " \
 154                         "setenv fdtfile imx6dl-wandboard-revb1.dtb; fi; " \
 155                 "if test $fdtfile = undefined; then " \
 156                         "echo WARNING: Could not determine dtb to use; fi; \0" \
 157         "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
 158         "pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
 159         "ramdisk_addr_r=0x13000000\0" \
 160         "ramdiskaddr=0x13000000\0" \
 161         "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
 162         BOOTENV
 163
 164 #define BOOT_TARGET_DEVICES(func) \
 165         func(MMC, mmc, 0) \
 166         func(MMC, mmc, 1) \
 167         func(USB, usb, 0) \
 168         func(PXE, pxe, na) \
 169         func(DHCP, dhcp, na)
 170
 171 #define CONFIG_BOOTCOMMAND \
 172            "run findfdt; " \
 173            "run distro_bootcmd"
 174
 175 #include <config_distro_bootcmd.h>
 176
 177 /* Physical Memory Map */
 178 #define CONFIG_NR_DRAM_BANKS            1
 179 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 180
 181 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 182 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 183 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 184
 185 #define CONFIG_SYS_INIT_SP_OFFSET \
 186         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 187 #define CONFIG_SYS_INIT_SP_ADDR \
 188         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 189
 190 /* Environment organization */
 191 #define CONFIG_ENV_SIZE                 (8 * 1024)
 192
 193 #define CONFIG_ENV_IS_IN_MMC
 194 #define CONFIG_ENV_OFFSET               (768 * 1024)
 195 #define CONFIG_SYS_MMC_ENV_DEV          0
 196
 197 #endif                         /* __CONFIG_H * */