include/configs/vme8349.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * esd vme8349 U-Boot configuration file
   4  * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
   5  *
   6  * (C) Copyright 2006-2010
   7  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   8  *
   9  * reinhard.arlt@esd-electronics.de
  10  * Based on the MPC8349EMDS config.
  11  */
  12
  13 /*
  14  * vme8349 board configuration file.
  15  */
  16
  17 #ifndef __CONFIG_H
  18 #define __CONFIG_H
  19
  20 /*
  21  * High Level Configuration Options
  22  */
  23 #define CONFIG_E300             1       /* E300 Family */
  24
  25 /* Don't enable PCI2 on vme834x - it doesn't exist physically. */
  26 #undef CONFIG_MPC83XX_PCI2              /* support for 2nd PCI controller */
  27
  28 #undef CONFIG_SYS_DRAM_TEST                     /* memory test, takes time */
  29 #define CONFIG_SYS_MEMTEST_START        0x00000000      /* memtest region */
  30 #define CONFIG_SYS_MEMTEST_END          0x00100000
  31
  32 /*
  33  * DDR Setup
  34  */
  35 #define CONFIG_DDR_ECC                  /* only for ECC DDR module */
  36 #define CONFIG_DDR_ECC_CMD              /* use DDR ECC user commands */
  37 #define CONFIG_SPD_EEPROM
  38 #define SPD_EEPROM_ADDRESS              0x54
  39 #define CONFIG_SYS_READ_SPD             vme8349_read_spd
  40 #define CONFIG_SYS_83XX_DDR_USES_CS0    /* esd; Fsl board uses CS2/CS3 */
  41
  42 /*
  43  * 32-bit data path mode.
  44  *
  45  * Please note that using this mode for devices with the real density of 64-bit
  46  * effectively reduces the amount of available memory due to the effect of
  47  * wrapping around while translating address to row/columns, for example in the
  48  * 256MB module the upper 128MB get aliased with contents of the lower
  49  * 128MB); normally this define should be used for devices with real 32-bit
  50  * data path.
  51  */
  52 #undef CONFIG_DDR_32BIT
  53
  54 #define CONFIG_SYS_SDRAM_BASE           0x00000000      /* DDR is sys memory*/
  55 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN \
  56                                         | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
  57 #define CONFIG_DDR_2T_TIMING
  58 #define CONFIG_SYS_DDRCDR               (DDRCDR_DHC_EN \
  59                                         | DDRCDR_ODT \
  60                                         | DDRCDR_Q_DRN)
  61                                         /* 0x80080001 */
  62
  63 /*
  64  * FLASH on the Local Bus
  65  */
  66 #define CONFIG_SYS_FLASH_BASE           0xf8000000      /* start of FLASH   */
  67 #define CONFIG_SYS_FLASH_SIZE           128             /* flash size in MB */
  68
  69
  70 #define CONFIG_SYS_WINDOW1_BASE         0xf0000000
  71
  72
  73 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
  74 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device*/
  75
  76 #undef CONFIG_SYS_FLASH_CHECKSUM
  77 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase TO (ms) */
  78 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write TO (ms) */
  79
  80 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  81
  82 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
  83 #define CONFIG_SYS_RAMBOOT
  84 #else
  85 #undef CONFIG_SYS_RAMBOOT
  86 #endif
  87
  88 #define CONFIG_SYS_INIT_RAM_LOCK        1
  89 #define CONFIG_SYS_INIT_RAM_ADDR        0xF7000000      /* Initial RAM addr */
  90 #define CONFIG_SYS_INIT_RAM_SIZE                0x1000          /* size */
  91
  92 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
  93                                          GENERATED_GBL_DATA_SIZE)
  94 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
  95
  96 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Reserve 256 kB */
  97 #define CONFIG_SYS_MALLOC_LEN           (256 * 1024)    /* Malloc size */
  98
  99 #undef CONFIG_SYS_LB_SDRAM      /* if board has SDRAM on local bus */
 100
 101 /*
 102  * Serial Port
 103  */
 104 #define CONFIG_SYS_NS16550_SERIAL
 105 #define CONFIG_SYS_NS16550_REG_SIZE     1
 106 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 107
 108 #define CONFIG_SYS_BAUDRATE_TABLE  \
 109                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 110
 111 #define CONFIG_SYS_NS16550_COM1         (CONFIG_SYS_IMMR + 0x4500)
 112 #define CONFIG_SYS_NS16550_COM2         (CONFIG_SYS_IMMR + 0x4600)
 113
 114 /* I2C */
 115 #define CONFIG_SYS_I2C
 116 #define CONFIG_SYS_I2C_FSL
 117 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 118 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 119 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 120 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 121 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 122 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 123 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 124 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
 125
 126 #define CONFIG_SYS_I2C_8574_ADDR2       0x20    /* I2C1, PCF8574 */
 127
 128 /* TSEC */
 129 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 130 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
 131 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 132 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
 133
 134 /*
 135  * General PCI
 136  * Addresses are mapped 1-1.
 137  */
 138 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 139 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 140 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 141 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 142 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 143 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
 144 #define CONFIG_SYS_PCI1_IO_BASE         0x00000000
 145 #define CONFIG_SYS_PCI1_IO_PHYS         0xE2000000
 146 #define CONFIG_SYS_PCI1_IO_SIZE         0x00100000      /* 1M */
 147
 148 #define CONFIG_SYS_PCI2_MEM_BASE        0xA0000000
 149 #define CONFIG_SYS_PCI2_MEM_PHYS        CONFIG_SYS_PCI2_MEM_BASE
 150 #define CONFIG_SYS_PCI2_MEM_SIZE        0x10000000      /* 256M */
 151 #define CONFIG_SYS_PCI2_MMIO_BASE       0xB0000000
 152 #define CONFIG_SYS_PCI2_MMIO_PHYS       CONFIG_SYS_PCI2_MMIO_BASE
 153 #define CONFIG_SYS_PCI2_MMIO_SIZE       0x10000000      /* 256M */
 154 #define CONFIG_SYS_PCI2_IO_BASE         0x00000000
 155 #define CONFIG_SYS_PCI2_IO_PHYS         0xE2100000
 156 #define CONFIG_SYS_PCI2_IO_SIZE         0x00100000      /* 1M */
 157
 158 #if defined(CONFIG_PCI)
 159
 160 #undef CONFIG_EEPRO100
 161 #undef CONFIG_TULIP
 162
 163 #if !defined(CONFIG_PCI_PNP)
 164         #define PCI_ENET0_IOADDR        0xFIXME
 165         #define PCI_ENET0_MEMADDR       0xFIXME
 166         #define PCI_IDSEL_NUMBER        0xFIXME
 167 #endif
 168
 169 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 170 #define CONFIG_SYS_PCI_SUBSYS_VENDORID  0x1957  /* Freescale */
 171
 172 #endif  /* CONFIG_PCI */
 173
 174 /*
 175  * TSEC configuration
 176  */
 177
 178 #if defined(CONFIG_TSEC_ENET)
 179
 180 #define CONFIG_GMII                     /* MII PHY management */
 181 #define CONFIG_TSEC1
 182 #define CONFIG_TSEC1_NAME       "TSEC0"
 183 #define CONFIG_TSEC2
 184 #define CONFIG_TSEC2_NAME       "TSEC1"
 185 #define CONFIG_PHY_M88E1111
 186 #define TSEC1_PHY_ADDR          0x08
 187 #define TSEC2_PHY_ADDR          0x10
 188 #define TSEC1_PHYIDX            0
 189 #define TSEC2_PHYIDX            0
 190 #define TSEC1_FLAGS             TSEC_GIGABIT
 191 #define TSEC2_FLAGS             TSEC_GIGABIT
 192
 193 /* Options are: TSEC[0-1] */
 194 #define CONFIG_ETHPRIME         "TSEC0"
 195
 196 #endif  /* CONFIG_TSEC_ENET */
 197
 198 /*
 199  * Environment
 200  */
 201 #ifndef CONFIG_SYS_RAMBOOT
 202 /* Address and size of Redundant Environment Sector     */
 203 #endif
 204
 205 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 206 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 207
 208 /*
 209  * BOOTP options
 210  */
 211 #define CONFIG_BOOTP_BOOTFILESIZE
 212
 213 /*
 214  * Command line configuration.
 215  */
 216 #define CONFIG_SYS_RTC_BUS_NUM  0x01
 217 #define CONFIG_SYS_I2C_RTC_ADDR 0x32
 218
 219 /* Pass Ethernet MAC to VxWorks */
 220 #define CONFIG_SYS_VXWORKS_MAC_PTR      0x000043f0
 221
 222 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 223
 224 /*
 225  * Miscellaneous configurable options
 226  */
 227 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 228
 229 /*
 230  * For booting Linux, the board info and command line data
 231  * have to be in the first 256 MB of memory, since this is
 232  * the maximum mapped by the Linux kernel during initialization.
 233  */
 234 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Init Memory map for Linux*/
 235
 236 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 237
 238 /* System IO Config */
 239 #define CONFIG_SYS_SICRH 0
 240 #define CONFIG_SYS_SICRL SICRL_LDP_A
 241
 242 #define CONFIG_SYS_GPIO1_PRELIM
 243 #define CONFIG_SYS_GPIO1_DIR    0x00100000
 244 #define CONFIG_SYS_GPIO1_DAT    0x00100000
 245
 246 #define CONFIG_SYS_GPIO2_PRELIM
 247 #define CONFIG_SYS_GPIO2_DIR    0x78900000
 248 #define CONFIG_SYS_GPIO2_DAT    0x70100000
 249
 250 #ifdef CONFIG_PCI
 251 #define CONFIG_PCI_INDIRECT_BRIDGE
 252 #endif
 253
 254 #if defined(CONFIG_CMD_KGDB)
 255 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 256 #endif
 257
 258 /*
 259  * Environment Configuration
 260  */
 261 #define CONFIG_ENV_OVERWRITE
 262
 263 #if defined(CONFIG_TSEC_ENET)
 264 #define CONFIG_HAS_ETH0
 265 #define CONFIG_HAS_ETH1
 266 #endif
 267
 268 #define CONFIG_HOSTNAME         "VME8349"
 269 #define CONFIG_ROOTPATH         "/tftpboot/rootfs"
 270 #define CONFIG_BOOTFILE         "uImage"
 271
 272 #define CONFIG_LOADADDR         800000  /* def location for tftp and bootm */
 273
 274 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 275         "netdev=eth0\0"                                                 \
 276         "hostname=vme8349\0"                                            \
 277         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 278                 "nfsroot=${serverip}:${rootpath}\0"                     \
 279         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 280         "addip=setenv bootargs ${bootargs} "                            \
 281                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 282                 ":${hostname}:${netdev}:off panic=1\0"                  \
 283         "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 284         "flash_nfs=run nfsargs addip addtty;"                           \
 285                 "bootm ${kernel_addr}\0"                                \
 286         "flash_self=run ramargs addip addtty;"                          \
 287                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 288         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 289                 "bootm\0"                                               \
 290         "load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0"              \
 291         "update=protect off fff00000 fff3ffff; "                        \
 292                 "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
 293         "upd=run load update\0"                                         \
 294         "fdtaddr=780000\0"                                              \
 295         "fdtfile=vme8349.dtb\0"                                         \
 296         ""
 297
 298 #define CONFIG_NFSBOOTCOMMAND                                           \
 299         "setenv bootargs root=/dev/nfs rw "                             \
 300                 "nfsroot=$serverip:$rootpath "                          \
 301                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 302                                                         "$netdev:off "  \
 303                 "console=$consoledev,$baudrate $othbootargs;"           \
 304         "tftp $loadaddr $bootfile;"                                     \
 305         "tftp $fdtaddr $fdtfile;"                                       \
 306         "bootm $loadaddr - $fdtaddr"
 307
 308 #define CONFIG_RAMBOOTCOMMAND                                           \
 309         "setenv bootargs root=/dev/ram rw "                             \
 310                 "console=$consoledev,$baudrate $othbootargs;"           \
 311         "tftp $ramdiskaddr $ramdiskfile;"                               \
 312         "tftp $loadaddr $bootfile;"                                     \
 313         "tftp $fdtaddr $fdtfile;"                                       \
 314         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 315
 316 #define CONFIG_BOOTCOMMAND      "run flash_self"
 317
 318 #ifndef __ASSEMBLY__
 319 int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
 320                      unsigned char *buffer, int len);
 321 #endif
 322
 323 #endif  /* __CONFIG_H */