include/configs/vf610twr.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2013 Freescale Semiconductor, Inc.
   4  *
   5  * Configuration settings for the Freescale Vybrid vf610twr board.
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 #include <asm/arch/imx-regs.h>
  12 #include <linux/stringify.h>
  13
  14 /* NAND support */
  15
  16 #ifdef CONFIG_CMD_NAND
  17 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  18 #define CONFIG_SYS_NAND_BASE            NFC_BASE_ADDR
  19
  20 /* Dynamic MTD partition support */
  21 #endif
  22
  23 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  24
  25 #define CONFIG_FEC_MXC_PHYADDR          0
  26
  27 /* I2C Configs */
  28
  29 /*
  30  * We do have 128MB of memory on the Vybrid Tower board. Leave the last
  31  * 16MB alone to avoid conflicts with Cortex-M4 firmwares running from
  32  * DDR3. Hence, limit the memory range for image processing to 112MB
  33  * using bootm_size. All of the following must be within this range.
  34  * We have the default load at 32MB into DDR (for the kernel), FDT at
  35  * 64MB and the ramdisk 512KB above that (allowing for hopefully never
  36  * seen large trees). This allows a reasonable split between ramdisk
  37  * and kernel size, where the ram disk can be a bit larger.
  38  */
  39 #define MEM_LAYOUT_ENV_SETTINGS \
  40         "bootm_size=0x07000000\0" \
  41         "loadaddr=0x82000000\0" \
  42         "kernel_addr_r=0x82000000\0" \
  43         "fdt_addr=0x84000000\0" \
  44         "fdt_addr_r=0x84000000\0" \
  45         "rdaddr=0x84080000\0" \
  46         "ramdisk_addr_r=0x84080000\0"
  47
  48 #define CONFIG_EXTRA_ENV_SETTINGS \
  49         MEM_LAYOUT_ENV_SETTINGS \
  50         "script=boot.scr\0" \
  51         "image=zImage\0" \
  52         "console=ttyLP1\0" \
  53         "fdt_file=vf610-twr.dtb\0" \
  54         "boot_fdt=try\0" \
  55         "ip_dyn=yes\0" \
  56         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
  57         "mmcpart=1\0" \
  58         "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
  59         "update_sd_firmware_filename=u-boot.imx\0" \
  60         "update_sd_firmware=" \
  61                 "if test ${ip_dyn} = yes; then " \
  62                         "setenv get_cmd dhcp; " \
  63                 "else " \
  64                         "setenv get_cmd tftp; " \
  65                 "fi; " \
  66                 "if mmc dev ${mmcdev}; then "   \
  67                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
  68                                 "setexpr fw_sz ${filesize} / 0x200; " \
  69                                 "setexpr fw_sz ${fw_sz} + 1; "  \
  70                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
  71                         "fi; "  \
  72                 "fi\0" \
  73         "mmcargs=setenv bootargs console=${console},${baudrate} " \
  74                 "root=${mmcroot}\0" \
  75         "loadbootscript=" \
  76                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
  77         "bootscript=echo Running bootscript from mmc ...; " \
  78                 "source\0" \
  79         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
  80         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
  81         "mmcboot=echo Booting from mmc ...; " \
  82                 "run mmcargs; " \
  83                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
  84                         "if run loadfdt; then " \
  85                                 "bootz ${loadaddr} - ${fdt_addr}; " \
  86                         "else " \
  87                                 "if test ${boot_fdt} = try; then " \
  88                                         "bootz; " \
  89                                 "else " \
  90                                         "echo WARN: Cannot load the DT; " \
  91                                 "fi; " \
  92                         "fi; " \
  93                 "else " \
  94                         "bootz; " \
  95                 "fi;\0" \
  96         "netargs=setenv bootargs console=${console},${baudrate} " \
  97                 "root=/dev/nfs " \
  98         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
  99                 "netboot=echo Booting from net ...; " \
 100                 "run netargs; " \
 101                 "if test ${ip_dyn} = yes; then " \
 102                         "setenv get_cmd dhcp; " \
 103                 "else " \
 104                         "setenv get_cmd tftp; " \
 105                 "fi; " \
 106                 "${get_cmd} ${image}; " \
 107                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 108                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 109                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 110                         "else " \
 111                                 "if test ${boot_fdt} = try; then " \
 112                                         "bootz; " \
 113                                 "else " \
 114                                         "echo WARN: Cannot load the DT; " \
 115                                 "fi; " \
 116                         "fi; " \
 117                 "else " \
 118                         "bootz; " \
 119                 "fi;\0"
 120
 121 /* Miscellaneous configurable options */
 122
 123 /* Physical memory map */
 124 #define PHYS_SDRAM                      (0x80000000)
 125 #define PHYS_SDRAM_SIZE                 (128 * 1024 * 1024)
 126
 127 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 128 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 129 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 130
 131 #endif