include/configs/tricorder.h

   1 /*
   2  * (C) Copyright 2006-2008
   3  * Texas Instruments.
   4  * Richard Woodruff <r-woodruff2@ti.com>
   5  * Syed Mohammed Khasim <x0khasim@ti.com>
   6  *
   7  * (C) Copyright 2012
   8  * Corscience GmbH & Co. KG
   9  * Thomas Weber <weber@corscience.de>
  10  *
  11  * Configuration settings for the Tricorder board.
  12  *
  13  * SPDX-License-Identifier:     GPL-2.0+
  14  */
  15
  16 #ifndef __CONFIG_H
  17 #define __CONFIG_H
  18
  19 /* High Level Configuration Options */
  20 #define CONFIG_OMAP                     /* in a TI OMAP core */
  21
  22 #define CONFIG_MACH_TYPE                MACH_TYPE_TRICORDER
  23 /*
  24  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  25  * 64 bytes before this address should be set aside for u-boot.img's
  26  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  27  * other needs.
  28  */
  29 #define CONFIG_SYS_TEXT_BASE            0x80100000
  30
  31 #define CONFIG_SDRC                     /* The chip has SDRC controller */
  32
  33 #include <asm/arch/cpu.h>               /* get chip and board defs */
  34 #include <asm/arch/omap.h>
  35
  36 /* Clock Defines */
  37 #define V_OSCK                          26000000 /* Clock output from T2 */
  38 #define V_SCLK                          (V_OSCK >> 1)
  39
  40 #define CONFIG_MISC_INIT_R
  41
  42 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
  43 #define CONFIG_SETUP_MEMORY_TAGS
  44 #define CONFIG_INITRD_TAG
  45 #define CONFIG_REVISION_TAG
  46
  47 /* Size of malloc() pool */
  48 #define CONFIG_SYS_MALLOC_LEN           (1024*1024)
  49
  50 /* Hardware drivers */
  51
  52 /* GPIO support */
  53 #define CONFIG_OMAP_GPIO
  54
  55 /* GPIO banks */
  56 #define CONFIG_OMAP3_GPIO_2             /* GPIO32..63 are in GPIO bank 2 */
  57
  58 /* LED support */
  59
  60 /* NS16550 Configuration */
  61 #define CONFIG_SYS_NS16550_SERIAL
  62 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  63 #define CONFIG_SYS_NS16550_CLK          48000000 /* 48MHz (APLL96/2) */
  64
  65 /* select serial console configuration */
  66 #define CONFIG_CONS_INDEX               3
  67 #define CONFIG_SYS_NS16550_COM3         OMAP34XX_UART3
  68 #define CONFIG_SERIAL3                  3
  69 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
  70                                         115200}
  71
  72 /* I2C */
  73 #define CONFIG_SYS_I2C
  74 #define CONFIG_SYS_OMAP24_I2C_SPEED     100000
  75 #define CONFIG_SYS_OMAP24_I2C_SLAVE     1
  76 #define CONFIG_SYS_I2C_OMAP34XX
  77
  78
  79 /* EEPROM */
  80 #define CONFIG_CMD_EEPROM
  81 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
  82 #define CONFIG_SYS_EEPROM_BUS_NUM       1
  83
  84 /* TWL4030 */
  85 #define CONFIG_TWL4030_LED
  86
  87 /* Board NAND Info */
  88 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
  89 #define MTDIDS_DEFAULT                  "nand0=omap2-nand.0"
  90 #define MTDPARTS_DEFAULT                "mtdparts=omap2-nand.0:" \
  91                                                 "128k(SPL)," \
  92                                                 "1m(u-boot)," \
  93                                                 "384k(u-boot-env1)," \
  94                                                 "1152k(mtdoops)," \
  95                                                 "384k(u-boot-env2)," \
  96                                                 "5m(kernel)," \
  97                                                 "2m(fdt)," \
  98                                                 "-(ubi)"
  99
 100 #define CONFIG_NAND_OMAP_GPMC
 101 #define CONFIG_SYS_NAND_ADDR            NAND_BASE       /* physical address */
 102                                                         /* to access nand */
 103 #define CONFIG_SYS_NAND_BASE            NAND_BASE       /* physical address */
 104                                                         /* to access nand at */
 105                                                         /* CS0 */
 106 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of NAND */
 107                                                         /* devices */
 108 #define CONFIG_BCH
 109 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 110 #define CONFIG_SYS_NAND_MAX_ECCPOS      56
 111
 112 /* commands to include */
 113 #define CONFIG_CMD_MTDPARTS             /* Enable MTD parts commands */
 114 #define CONFIG_CMD_NAND                 /* NAND support */
 115 #define CONFIG_CMD_NAND_LOCK_UNLOCK     /* nand (un)lock commands */
 116 #define CONFIG_CMD_UBIFS                /* UBIFS commands */
 117 #define CONFIG_LZO                      /* LZO is needed for UBIFS */
 118
 119 #undef CONFIG_CMD_JFFS2                 /* JFFS2 Support */
 120
 121 /* needed for ubi */
 122 #define CONFIG_RBTREE
 123 #define CONFIG_MTD_DEVICE       /* needed for mtdparts commands */
 124 #define CONFIG_MTD_PARTITIONS
 125
 126 /* Environment information (this is the common part) */
 127
 128
 129 /* hang() the board on panic() */
 130 #define CONFIG_PANIC_HANG
 131
 132 /* environment placement (for NAND), is different for FLASHCARD but does not
 133  * harm there */
 134 #define CONFIG_ENV_OFFSET               0x120000    /* env start */
 135 #define CONFIG_ENV_OFFSET_REDUND        0x2A0000    /* redundant env start */
 136 #define CONFIG_ENV_SIZE                 (16 << 10)  /* use 16KiB for env */
 137 #define CONFIG_ENV_RANGE                (384 << 10) /* allow badblocks in env */
 138
 139 /* the loadaddr is the same as CONFIG_SYS_LOAD_ADDR, unfortunately the defiend
 140  * value can not be used here! */
 141 #define CONFIG_LOADADDR         0x82000000
 142
 143 #define CONFIG_COMMON_ENV_SETTINGS \
 144         "console=ttyO2,115200n8\0" \
 145         "mmcdev=0\0" \
 146         "vram=3M\0" \
 147         "defaultdisplay=lcd\0" \
 148         "kernelopts=mtdoops.mtddev=3\0" \
 149         "mtdparts=" MTDPARTS_DEFAULT "\0" \
 150         "mtdids=" MTDIDS_DEFAULT "\0" \
 151         "commonargs=" \
 152                 "setenv bootargs console=${console} " \
 153                 "${mtdparts} " \
 154                 "${kernelopts} " \
 155                 "vt.global_cursor_default=0 " \
 156                 "vram=${vram} " \
 157                 "omapdss.def_disp=${defaultdisplay}\0"
 158
 159 #define CONFIG_BOOTCOMMAND "run autoboot"
 160
 161 /* specific environment settings for different use cases
 162  * FLASHCARD: used to run a rdimage from sdcard to program the device
 163  * 'NORMAL': used to boot kernel from sdcard, nand, ...
 164  *
 165  * The main aim for the FLASHCARD skin is to have an embedded environment
 166  * which will not be influenced by any data already on the device.
 167  */
 168 #ifdef CONFIG_FLASHCARD
 169
 170 #define CONFIG_ENV_IS_NOWHERE
 171
 172 /* the rdaddr is 16 MiB before the loadaddr */
 173 #define CONFIG_ENV_RDADDR       "rdaddr=0x81000000\0"
 174
 175 #define CONFIG_EXTRA_ENV_SETTINGS \
 176         CONFIG_COMMON_ENV_SETTINGS \
 177         CONFIG_ENV_RDADDR \
 178         "autoboot=" \
 179         "run commonargs; " \
 180         "setenv bootargs ${bootargs} " \
 181                 "flashy_updateimg=/dev/mmcblk0p1:corscience_update.img " \
 182                 "rdinit=/sbin/init; " \
 183         "mmc dev ${mmcdev}; mmc rescan; " \
 184         "fatload mmc ${mmcdev} ${loadaddr} uImage; " \
 185         "fatload mmc ${mmcdev} ${rdaddr} uRamdisk; " \
 186         "bootm ${loadaddr} ${rdaddr}\0"
 187
 188 #else /* CONFIG_FLASHCARD */
 189
 190 #define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */
 191
 192 #define CONFIG_ENV_IS_IN_NAND
 193
 194 #define CONFIG_EXTRA_ENV_SETTINGS \
 195         CONFIG_COMMON_ENV_SETTINGS \
 196         "mmcargs=" \
 197                 "run commonargs; " \
 198                 "setenv bootargs ${bootargs} " \
 199                 "root=/dev/mmcblk0p2 " \
 200                 "rootwait " \
 201                 "rw\0" \
 202         "nandargs=" \
 203                 "run commonargs; " \
 204                 "setenv bootargs ${bootargs} " \
 205                 "root=ubi0:root " \
 206                 "ubi.mtd=7 " \
 207                 "rootfstype=ubifs " \
 208                 "ro\0" \
 209         "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 210         "bootscript=echo Running bootscript from mmc ...; " \
 211                 "source ${loadaddr}\0" \
 212         "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 213         "mmcboot=echo Booting from mmc ...; " \
 214                 "run mmcargs; " \
 215                 "bootm ${loadaddr}\0" \
 216         "loaduimage_ubi=ubi part ubi; " \
 217                 "ubifsmount ubi:root; " \
 218                 "ubifsload ${loadaddr} /boot/uImage\0" \
 219         "loaduimage_nand=nand read ${loadaddr} kernel 0x500000\0" \
 220         "nandboot=echo Booting from nand ...; " \
 221                 "run nandargs; " \
 222                 "run loaduimage_nand; " \
 223                 "bootm ${loadaddr}\0" \
 224         "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
 225                         "if run loadbootscript; then " \
 226                                 "run bootscript; " \
 227                         "else " \
 228                                 "if run loaduimage; then " \
 229                                         "run mmcboot; " \
 230                                 "else run nandboot; " \
 231                                 "fi; " \
 232                         "fi; " \
 233                 "else run nandboot; fi\0"
 234
 235 #endif /* CONFIG_FLASHCARD */
 236
 237 /* Miscellaneous configurable options */
 238 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 239 #define CONFIG_CMDLINE_EDITING          /* enable cmdline history */
 240 #define CONFIG_AUTO_COMPLETE
 241 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 242 /* Print Buffer Size */
 243 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 244                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 245 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 246
 247 /* Boot Argument Buffer Size */
 248 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 249
 250 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0 + 0x00000000)
 251 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + \
 252                                         0x07000000) /* 112 MB */
 253
 254 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0 + 0x02000000)
 255
 256 /*
 257  * OMAP3 has 12 GP timers, they can be driven by the system clock
 258  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 259  * This rate is divided by a local divisor.
 260  */
 261 #define CONFIG_SYS_TIMERBASE            (OMAP34XX_GPT2)
 262 #define CONFIG_SYS_PTV                  2 /* Divisor: 2^(PTV+1) => 8 */
 263
 264 /*  Physical Memory Map  */
 265 #define CONFIG_NR_DRAM_BANKS            2 /* CS1 may or may not be populated */
 266 #define PHYS_SDRAM_1                    OMAP34XX_SDRC_CS0
 267 #define PHYS_SDRAM_2                    OMAP34XX_SDRC_CS1
 268
 269 /* NAND and environment organization  */
 270 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 2 sectors */
 271
 272 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 273 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 274 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 275 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
 276                                                 CONFIG_SYS_INIT_RAM_SIZE - \
 277                                                 GENERATED_GBL_DATA_SIZE)
 278
 279 /* SRAM config */
 280 #define CONFIG_SYS_SRAM_START           0x40200000
 281 #define CONFIG_SYS_SRAM_SIZE            0x10000
 282
 283 /* Defines for SPL */
 284 #define CONFIG_SPL_FRAMEWORK
 285 #define CONFIG_SPL_NAND_SIMPLE
 286
 287 #define CONFIG_SPL_BOARD_INIT
 288 #define CONFIG_SPL_NAND_BASE
 289 #define CONFIG_SPL_NAND_DRIVERS
 290 #define CONFIG_SPL_NAND_ECC
 291 #define CONFIG_SPL_LDSCRIPT             "arch/arm/mach-omap2/u-boot-spl.lds"
 292 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME        "u-boot.img"
 293 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 294
 295 #define CONFIG_SPL_TEXT_BASE            0x40200000 /*CONFIG_SYS_SRAM_START*/
 296 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 297                                          CONFIG_SPL_TEXT_BASE)
 298
 299 #define CONFIG_SPL_BSS_START_ADDR       0x80000000 /*CONFIG_SYS_SDRAM_BASE*/
 300 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 301
 302 /* NAND boot config */
 303 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 304 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 305 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 306 #define CONFIG_SYS_NAND_OOBSIZE         64
 307 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
 308 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   NAND_LARGE_BADBLOCK_POS
 309 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
 310                                          13, 14, 16, 17, 18, 19, 20, 21, 22, \
 311                                          23, 24, 25, 26, 27, 28, 30, 31, 32, \
 312                                          33, 34, 35, 36, 37, 38, 39, 40, 41, \
 313                                          42, 44, 45, 46, 47, 48, 49, 50, 51, \
 314                                          52, 53, 54, 55, 56}
 315
 316 #define CONFIG_SYS_NAND_ECCSIZE         512
 317 #define CONFIG_SYS_NAND_ECCBYTES        13
 318 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
 319
 320 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 321
 322 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x20000
 323 #define CONFIG_SYS_NAND_U_BOOT_SIZE     0x100000
 324
 325 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
 326 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000        /* 1 MB */
 327
 328 #define CONFIG_SYS_ALT_MEMTEST
 329 #define CONFIG_SYS_MEMTEST_SCRATCH      0x81000000
 330 #endif /* __CONFIG_H */