include/configs/tam3517-common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2011
   4  * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
   5  *
   6  * Copyright (C) 2009 TechNexion Ltd.
   7  */
   8
   9 #ifndef __TAM3517_H
  10 #define __TAM3517_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15
  16 #include <asm/arch/cpu.h>               /* get chip and board defs */
  17 #include <asm/arch/omap.h>
  18
  19 /* Clock Defines */
  20 #define V_OSCK                  26000000        /* Clock output from T2 */
  21 #define V_SCLK                  (V_OSCK >> 1)
  22
  23 #define CONFIG_CMDLINE_TAG                      /* enable passing of ATAGs */
  24 #define CONFIG_SETUP_MEMORY_TAGS
  25 #define CONFIG_INITRD_TAG
  26 #define CONFIG_REVISION_TAG
  27
  28 /*
  29  * Size of malloc() pool
  30  */
  31 #define CONFIG_ENV_SIZE                 (128 << 10)     /* 128 KiB sector */
  32 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + (128 << 10) + \
  33                                         2 * 1024 * 1024)
  34 /*
  35  * DDR related
  36  */
  37 #define CONFIG_SYS_CS0_SIZE             (256 * 1024 * 1024)
  38
  39 /*
  40  * Hardware drivers
  41  */
  42
  43 /*
  44  * NS16550 Configuration
  45  */
  46 #define CONFIG_SYS_NS16550_SERIAL
  47 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  48 #define CONFIG_SYS_NS16550_CLK          48000000        /* 48MHz (APLL96/2) */
  49
  50 /*
  51  * select serial console configuration
  52  */
  53 #define CONFIG_SYS_NS16550_COM1         OMAP34XX_UART1
  54
  55 /* allow to overwrite serial and ethaddr */
  56 #define CONFIG_ENV_OVERWRITE
  57 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
  58                                         115200}
  59 /* EHCI */
  60 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO        25
  61
  62 #define CONFIG_SYS_I2C
  63 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* base address */
  64 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1               /* bytes of address */
  65 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
  66
  67 /*
  68  * Board NAND Info.
  69  */
  70 #define CONFIG_SYS_NAND_BASE            NAND_BASE       /* physical address */
  71                                                         /* to access */
  72                                                         /* nand at CS0 */
  73
  74 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of */
  75                                                         /* NAND devices */
  76
  77 /*
  78  * Miscellaneous configurable options
  79  */
  80 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
  81
  82 #define CONFIG_SYS_MAXARGS              32      /* max number of command */
  83                                                 /* args */
  84 /* memtest works on */
  85 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0)
  86 #define CONFIG_SYS_MEMTEST_END          (OMAP34XX_SDRC_CS0 + \
  87                                         0x01F00000) /* 31MB */
  88
  89 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0) /* default load */
  90                                                                 /* address */
  91
  92 /*
  93  * AM3517 has 12 GP timers, they can be driven by the system clock
  94  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
  95  * This rate is divided by a local divisor.
  96  */
  97 #define CONFIG_SYS_TIMERBASE            OMAP34XX_GPT2
  98 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
  99
 100 /*
 101  * Physical Memory Map
 102  */
 103 #define PHYS_SDRAM_1            OMAP34XX_SDRC_CS0
 104 #define PHYS_SDRAM_2            OMAP34XX_SDRC_CS1
 105
 106 /*
 107  * FLASH and environment organization
 108  */
 109
 110 /* **** PISMO SUPPORT *** */
 111
 112 /* Redundant Environment */
 113 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 114 #define CONFIG_ENV_OFFSET               0x180000
 115 #define CONFIG_ENV_ADDR                 0x180000
 116 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 117                                                 2 * CONFIG_SYS_ENV_SECT_SIZE)
 118 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 119
 120 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 121 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 122 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 123 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 124                                          CONFIG_SYS_INIT_RAM_SIZE - \
 125                                          GENERATED_GBL_DATA_SIZE)
 126
 127 /*
 128  * ethernet support, EMAC
 129  *
 130  */
 131 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
 132 #define CONFIG_BOOTP_DNS2
 133 #define CONFIG_BOOTP_SEND_HOSTNAME
 134 #define CONFIG_NET_RETRY_COUNT 10
 135
 136 /* Defines for SPL */
 137 #define CONFIG_SPL_CONSOLE
 138 #define CONFIG_SPL_NAND_SOFTECC
 139 #define CONFIG_SPL_NAND_WORKSPACE       0x8f07f000 /* below BSS */
 140
 141 #define CONFIG_SPL_NAND_BASE
 142 #define CONFIG_SPL_NAND_DRIVERS
 143 #define CONFIG_SPL_NAND_ECC
 144
 145 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 146                                          CONFIG_SPL_TEXT_BASE)
 147 #define CONFIG_SPL_STACK                LOW_LEVEL_SRAM_STACK
 148
 149 #define CONFIG_SYS_SPL_MALLOC_START     0x8f000000
 150 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x80000
 151 #define CONFIG_SPL_BSS_START_ADDR       0x8f080000 /* end of RAM */
 152 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 153
 154 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 155 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME         "u-boot.img"
 156
 157 /* FAT */
 158 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME          "uImage"
 159 #define CONFIG_SPL_FS_LOAD_ARGS_NAME            "args"
 160
 161 /* RAW SD card / eMMC */
 162 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900   /* address 0x120000 */
 163 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0x80    /* address 0x10000 */
 164 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  0x80    /* 64KiB */
 165
 166 /* NAND boot config */
 167 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 168 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 169 #define CONFIG_SYS_NAND_OOBSIZE         64
 170 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 171 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 172 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 173 #define CONFIG_SYS_NAND_ECCPOS          {40, 41, 42, 43, 44, 45, 46, 47,\
 174                                          48, 49, 50, 51, 52, 53, 54, 55,\
 175                                          56, 57, 58, 59, 60, 61, 62, 63}
 176 #define CONFIG_SYS_NAND_ECCSIZE         256
 177 #define CONFIG_SYS_NAND_ECCBYTES        3
 178 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_SW
 179
 180 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 181
 182 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 183 #define CONFIG_SYS_NAND_U_BOOT_SIZE     0x80000
 184
 185 /* Setup MTD for NAND on the SOM */
 186
 187 #define CONFIG_TAM3517_SETTINGS                                         \
 188         "netdev=eth0\0"                                                 \
 189         "nandargs=setenv bootargs root=${nandroot} "                    \
 190                 "rootfstype=${nandrootfstype}\0"                        \
 191         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 192                 "nfsroot=${serverip}:${rootpath}\0"                     \
 193         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 194         "addip_sta=setenv bootargs ${bootargs} "                        \
 195                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 196                 ":${hostname}:${netdev}:off panic=1\0"                  \
 197         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 198         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
 199                 "else run addip_sta;fi\0"                               \
 200         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 201         "addtty=setenv bootargs ${bootargs}"                            \
 202                 " console=ttyO0,${baudrate}\0"                          \
 203         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
 204         "loadaddr=82000000\0"                                           \
 205         "kernel_addr_r=82000000\0"                                      \
 206         "hostname=" CONFIG_HOSTNAME "\0"                        \
 207         "bootfile=" CONFIG_HOSTNAME "/uImage\0"         \
 208         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 209                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 210         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 211                 "bootm ${kernel_addr}\0"                                \
 212         "nandboot=run nandargs addip addtty addmtd addmisc;"            \
 213                 "nand read ${kernel_addr_r} kernel\0"                   \
 214                 "bootm ${kernel_addr_r}\0"                              \
 215         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 216                 "run nfsargs addip addtty addmtd addmisc;"              \
 217                 "bootm ${kernel_addr_r}\0"                              \
 218         "net_self=if run net_self_load;then "                           \
 219                 "run ramargs addip addtty addmtd addmisc;"              \
 220                 "bootm ${kernel_addr_r} ${ramdisk_addr_r};"             \
 221                 "else echo Images not loades;fi\0"                      \
 222         "u-boot=" CONFIG_HOSTNAME "/u-boot.img\0"               \
 223         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 224         "loadmlo=tftp ${loadaddr} ${mlo}\0"                             \
 225         "mlo=" CONFIG_HOSTNAME "/MLO\0"                 \
 226         "uboot_addr=0x80000\0"                                          \
 227         "update=nandecc sw;nand erase ${uboot_addr} 100000;"            \
 228                 "nand write ${loadaddr} ${uboot_addr} 80000\0"          \
 229         "updatemlo=nandecc hw;nand erase 0 20000;"                      \
 230                 "nand write ${loadaddr} 0 20000\0"                      \
 231         "upd=if run load;then echo Updating u-boot;if run update;"      \
 232                 "then echo U-Boot updated;"                             \
 233                         "else echo Error updating u-boot !;"            \
 234                         "echo Board without bootloader !!;"             \
 235                 "fi;"                                                   \
 236                 "else echo U-Boot not downloaded..exiting;fi\0"         \
 237
 238 /*
 239  * this is common code for all TAM3517 boards.
 240  * MAC address is stored from manufacturer in
 241  * I2C EEPROM
 242  */
 243 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
 244 /*
 245  * The I2C EEPROM on the TAM3517 contains
 246  * mac address and production data
 247  */
 248 struct tam3517_module_info {
 249         char customer[48];
 250         char product[48];
 251
 252         /*
 253          * bit 0~47  : sequence number
 254          * bit 48~55 : week of year, from 0.
 255          * bit 56~63 : year
 256          */
 257         unsigned long long sequence_number;
 258
 259         /*
 260          * bit 0~7   : revision fixed
 261          * bit 8~15  : revision major
 262          * bit 16~31 : TNxxx
 263          */
 264         unsigned int revision;
 265         unsigned char eth_addr[4][8];
 266         unsigned char _rev[100];
 267 };
 268
 269 #define TAM3517_READ_EEPROM(info, ret) \
 270 do {                                                            \
 271         i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
 272         if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,          \
 273                 (void *)info, sizeof(*info)))                   \
 274                 ret = 1;                                        \
 275         else                                                    \
 276                 ret = 0;                                        \
 277 } while (0)
 278
 279 #define TAM3517_READ_MAC_FROM_EEPROM(info)                      \
 280 do {                                                            \
 281         char buf[80], ethname[20];                              \
 282         int i;                                                  \
 283         memset(buf, 0, sizeof(buf));                            \
 284         for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) {   \
 285                 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X",   \
 286                         (info)->eth_addr[i][5],                 \
 287                         (info)->eth_addr[i][4],                 \
 288                         (info)->eth_addr[i][3],                 \
 289                         (info)->eth_addr[i][2],                 \
 290                         (info)->eth_addr[i][1],                 \
 291                         (info)->eth_addr[i][0]);                        \
 292                                                                 \
 293                 if (i)                                          \
 294                         sprintf(ethname, "eth%daddr", i);       \
 295                 else                                            \
 296                         strcpy(ethname, "ethaddr");             \
 297                 printf("Setting %s from EEPROM with %s\n", ethname, buf);\
 298                 env_set(ethname, buf);                          \
 299         }                                                       \
 300 } while (0)
 301
 302 /* The following macros are taken from Technexion's documentation */
 303 #define TAM3517_sequence_number(info) \
 304         ((info)->sequence_number % 0x1000000000000LL)
 305 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100)
 306 #define TAM3517_year(info) ((info)->sequence_number >> 56)
 307 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100)
 308 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100)
 309 #define TAM3517_revision_tn(info) ((info)->revision >> 16)
 310
 311 #define TAM3517_PRINT_SOM_INFO(info)                            \
 312 do {                                                            \
 313         printf("Vendor:%s\n", (info)->customer);                \
 314         printf("SOM:   %s\n", (info)->product);                 \
 315         printf("SeqNr: %02llu%02llu%012llu\n",                  \
 316                 TAM3517_year(info),                             \
 317                 TAM3517_week_of_year(info),                     \
 318                 TAM3517_sequence_number(info));                 \
 319         printf("Rev:   TN%u %u.%u\n",                           \
 320                 TAM3517_revision_tn(info),                      \
 321                 TAM3517_revision_major(info),                   \
 322                 TAM3517_revision_fixed(info));                  \
 323 } while (0)
 324
 325 #endif
 326
 327 #endif /* __TAM3517_H */