include/configs/strider.h

   1 /*
   2  * (C) Copyright 2014
   3  * Dirk Eibach,  Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
   4  *
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15 #define CONFIG_E300             1 /* E300 family */
  16 #define CONFIG_MPC83xx          1 /* MPC83xx family */
  17 #define CONFIG_MPC830x          1 /* MPC830x family */
  18 #define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
  19 #define CONFIG_STRIDER          1 /* STRIDER board specific */
  20
  21 #define CONFIG_BOARD_EARLY_INIT_R
  22 #define CONFIG_LAST_STAGE_INIT
  23
  24 #define CONFIG_FSL_ESDHC
  25 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
  26
  27 #define CONFIG_SYS_ALT_MEMTEST
  28
  29 /*
  30  * System Clock Setup
  31  */
  32 #define CONFIG_83XX_CLKIN       33333333 /* in Hz */
  33 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
  34
  35 /*
  36  * Hardware Reset Configuration Word
  37  * if CLKIN is 66.66MHz, then
  38  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
  39  * We choose the A type silicon as default, so the core is 400Mhz.
  40  */
  41 #define CONFIG_SYS_HRCW_LOW (\
  42         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  43         HRCWL_DDR_TO_SCB_CLK_2X1 |\
  44         HRCWL_SVCOD_DIV_2 |\
  45         HRCWL_CSB_TO_CLKIN_4X1 |\
  46         HRCWL_CORE_TO_CSB_3X1)
  47 /*
  48  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
  49  * in 8308's HRCWH according to the manual, but original Freescale's
  50  * code has them and I've expirienced some problems using the board
  51  * with BDI3000 attached when I've tried to set these bits to zero
  52  * (UART doesn't work after the 'reset run' command).
  53  */
  54 #define CONFIG_SYS_HRCW_HIGH (\
  55         HRCWH_PCI_HOST |\
  56         HRCWH_PCI1_ARBITER_ENABLE |\
  57         HRCWH_CORE_ENABLE |\
  58         HRCWH_FROM_0XFFF00100 |\
  59         HRCWH_BOOTSEQ_DISABLE |\
  60         HRCWH_SW_WATCHDOG_DISABLE |\
  61         HRCWH_ROM_LOC_LOCAL_16BIT |\
  62         HRCWH_RL_EXT_LEGACY |\
  63         HRCWH_TSEC1M_IN_MII |\
  64         HRCWH_TSEC2M_IN_RGMII |\
  65         HRCWH_BIG_ENDIAN)
  66
  67 /*
  68  * System IO Config
  69  */
  70 #define CONFIG_SYS_SICRH (\
  71         SICRH_ESDHC_A_SD |\
  72         SICRH_ESDHC_B_SD |\
  73         SICRH_ESDHC_C_SD |\
  74         SICRH_GPIO_A_GPIO |\
  75         SICRH_GPIO_B_GPIO |\
  76         SICRH_IEEE1588_A_GPIO |\
  77         SICRH_USB |\
  78         SICRH_GTM_GPIO |\
  79         SICRH_IEEE1588_B_GPIO |\
  80         SICRH_ETSEC2_GPIO |\
  81         SICRH_GPIOSEL_1 |\
  82         SICRH_TMROBI_V3P3 |\
  83         SICRH_TSOBI1_V2P5 |\
  84         SICRH_TSOBI2_V2P5)      /* 0x0037f103 */
  85 #define CONFIG_SYS_SICRL (\
  86         SICRL_SPI_PF0 |\
  87         SICRL_UART_PF0 |\
  88         SICRL_IRQ_PF0 |\
  89         SICRL_I2C2_PF0 |\
  90         SICRL_ETSEC1_TX_CLK)    /* 0x00000000 */
  91
  92 /*
  93  * IMMR new address
  94  */
  95 #define CONFIG_SYS_IMMR         0xE0000000
  96
  97 /*
  98  * SERDES
  99  */
 100 #define CONFIG_FSL_SERDES
 101 #define CONFIG_FSL_SERDES1      0xe3000
 102
 103 /*
 104  * Arbiter Setup
 105  */
 106 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
 107 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
 108 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
 109
 110 /*
 111  * DDR Setup
 112  */
 113 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
 114 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
 115 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
 116 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 117 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 118                                 | DDRCDR_PZ_LOZ \
 119                                 | DDRCDR_NZ_LOZ \
 120                                 | DDRCDR_ODT \
 121                                 | DDRCDR_Q_DRN)
 122                                 /* 0x7b880001 */
 123 /*
 124  * Manually set up DDR parameters
 125  * consist of one chip NT5TU64M16HG from NANYA
 126  */
 127
 128 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
 129
 130 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
 131 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 132                                 | CSCONFIG_ODT_RD_NEVER \
 133                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
 134                                 | CSCONFIG_BANK_BIT_3 \
 135                                 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
 136                                 /* 0x80010102 */
 137 #define CONFIG_SYS_DDR_TIMING_3 0
 138 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
 139                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
 140                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 141                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 142                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 143                                 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 144                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 145                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 146                                 /* 0x00260802 */
 147 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 148                                 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 149                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 150                                 | (7 << TIMING_CFG1_CASLAT_SHIFT) \
 151                                 | (9 << TIMING_CFG1_REFREC_SHIFT) \
 152                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
 153                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 154                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 155                                 /* 0x26279222 */
 156 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
 157                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
 158                                 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 159                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 160                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 161                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 162                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 163                                 /* 0x021848c5 */
 164 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
 165                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 166                                 /* 0x08240100 */
 167 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 168                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 169                                 | SDRAM_CFG_DBW_16)
 170                                 /* 0x43100000 */
 171
 172 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
 173 #define CONFIG_SYS_DDR_MODE             ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
 174                                 | (0x0242 << SDRAM_MODE_SD_SHIFT))
 175                                 /* ODT 150ohm CL=4, AL=0 on SDRAM */
 176 #define CONFIG_SYS_DDR_MODE2            0x00000000
 177
 178 /*
 179  * Memory test
 180  */
 181 #define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
 182 #define CONFIG_SYS_MEMTEST_END          0x07f00000
 183
 184 /*
 185  * The reserved memory
 186  */
 187 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 188
 189 #define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
 190 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 191
 192 /*
 193  * Initial RAM Base Address Setup
 194  */
 195 #define CONFIG_SYS_INIT_RAM_LOCK        1
 196 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 197 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 198 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 199         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 200
 201 /*
 202  * Local Bus Configuration & Clock Setup
 203  */
 204 #define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
 205 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
 206 #define CONFIG_SYS_LBC_LBCR             0x00040000
 207
 208 /*
 209  * FLASH on the Local Bus
 210  */
 211 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 212 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 213 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 214 #define CONFIG_FLASH_CFI_LEGACY
 215 #define CONFIG_SYS_FLASH_LEGACY_512Kx16
 216
 217 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 218 #define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is up to 8M */
 219 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */
 220
 221 /* Window base at flash base */
 222 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 223 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 224
 225 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 226                                 | BR_PS_16      /* 16 bit port */ \
 227                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 228                                 | BR_V)         /* valid */
 229 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 230                                 | OR_UPM_XAM \
 231                                 | OR_GPCM_CSNT \
 232                                 | OR_GPCM_ACS_DIV2 \
 233                                 | OR_GPCM_XACS \
 234                                 | OR_GPCM_SCY_15 \
 235                                 | OR_GPCM_TRLX_SET \
 236                                 | OR_GPCM_EHTR_SET)
 237
 238 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 239 #define CONFIG_SYS_MAX_FLASH_SECT       135
 240
 241 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 242 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 243
 244 /*
 245  * FPGA
 246  */
 247 #define CONFIG_SYS_FPGA0_BASE           0xE0600000
 248 #define CONFIG_SYS_FPGA0_SIZE           1 /* FPGA size is 1M */
 249
 250 /* Window base at FPGA base */
 251 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_FPGA0_BASE
 252 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_1MB)
 253
 254 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FPGA0_BASE \
 255                                 | BR_PS_16      /* 16 bit port */ \
 256                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 257                                 | BR_V)         /* valid */
 258
 259 #define CONFIG_SYS_OR1_PRELIM   (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
 260                                 | OR_UPM_XAM \
 261                                 | OR_GPCM_CSNT \
 262                                 | OR_GPCM_SCY_5 \
 263                                 | OR_GPCM_TRLX_CLEAR \
 264                                 | OR_GPCM_EHTR_CLEAR)
 265
 266 #define CONFIG_SYS_FPGA_BASE(k)         CONFIG_SYS_FPGA0_BASE
 267 #define CONFIG_SYS_FPGA_DONE(k)         0x0010
 268
 269 #define CONFIG_SYS_FPGA_COUNT           1
 270
 271 #define CONFIG_SYS_MCLINK_MAX           3
 272
 273 #define CONFIG_SYS_FPGA_PTR \
 274         { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
 275
 276 #define CONFIG_SYS_FPGA_NO_RFL_HI
 277
 278 /*
 279  * Serial Port
 280  */
 281 #define CONFIG_CONS_INDEX       2
 282 #define CONFIG_SYS_NS16550_SERIAL
 283 #define CONFIG_SYS_NS16550_REG_SIZE     1
 284 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 285
 286 #define CONFIG_SYS_BAUDRATE_TABLE  \
 287         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 288
 289 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 290 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 291
 292 /* Pass open firmware flat tree */
 293
 294 /* I2C */
 295 #define CONFIG_SYS_I2C
 296 #define CONFIG_SYS_I2C_FSL
 297 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 298 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 299 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 300
 301 #define CONFIG_PCA953X                  /* NXP PCA9554 */
 302 #define CONFIG_SYS_I2C_PCA953X_WIDTH    { {0x24, 16}, {0x25, 16}, {0x26, 16}, \
 303                                           {0x3c, 8}, {0x3d, 8}, {0x3e, 8} }
 304
 305 #define CONFIG_PCA9698                  /* NXP PCA9698 */
 306
 307 #define CONFIG_SYS_I2C_IHS
 308 #define CONFIG_SYS_I2C_IHS_CH0
 309 #define CONFIG_SYS_I2C_IHS_SPEED_0              50000
 310 #define CONFIG_SYS_I2C_IHS_SLAVE_0              0x7F
 311 #define CONFIG_SYS_I2C_IHS_CH1
 312 #define CONFIG_SYS_I2C_IHS_SPEED_1              50000
 313 #define CONFIG_SYS_I2C_IHS_SLAVE_1              0x7F
 314 #define CONFIG_SYS_I2C_IHS_CH2
 315 #define CONFIG_SYS_I2C_IHS_SPEED_2              50000
 316 #define CONFIG_SYS_I2C_IHS_SLAVE_2              0x7F
 317 #define CONFIG_SYS_I2C_IHS_CH3
 318 #define CONFIG_SYS_I2C_IHS_SPEED_3              50000
 319 #define CONFIG_SYS_I2C_IHS_SLAVE_3              0x7F
 320
 321 #ifdef CONFIG_STRIDER_CON_DP
 322 #define CONFIG_SYS_I2C_IHS_DUAL
 323 #define CONFIG_SYS_I2C_IHS_CH0_1
 324 #define CONFIG_SYS_I2C_IHS_SPEED_0_1            50000
 325 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1            0x7F
 326 #define CONFIG_SYS_I2C_IHS_CH1_1
 327 #define CONFIG_SYS_I2C_IHS_SPEED_1_1            50000
 328 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1            0x7F
 329 #define CONFIG_SYS_I2C_IHS_CH2_1
 330 #define CONFIG_SYS_I2C_IHS_SPEED_2_1            50000
 331 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1            0x7F
 332 #define CONFIG_SYS_I2C_IHS_CH3_1
 333 #define CONFIG_SYS_I2C_IHS_SPEED_3_1            50000
 334 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1            0x7F
 335 #endif
 336
 337 /*
 338  * Software (bit-bang) I2C driver configuration
 339  */
 340 #define CONFIG_SYS_I2C_SOFT
 341 #define CONFIG_SOFT_I2C_READ_REPEATED_START
 342 #define CONFIG_SYS_I2C_SOFT_SPEED               50000
 343 #define CONFIG_SYS_I2C_SOFT_SLAVE               0x7F
 344 #define I2C_SOFT_DECLARATIONS2
 345 #define CONFIG_SYS_I2C_SOFT_SPEED_2             50000
 346 #define CONFIG_SYS_I2C_SOFT_SLAVE_2             0x7F
 347 #define I2C_SOFT_DECLARATIONS3
 348 #define CONFIG_SYS_I2C_SOFT_SPEED_3             50000
 349 #define CONFIG_SYS_I2C_SOFT_SLAVE_3             0x7F
 350 #define I2C_SOFT_DECLARATIONS4
 351 #define CONFIG_SYS_I2C_SOFT_SPEED_4             50000
 352 #define CONFIG_SYS_I2C_SOFT_SLAVE_4             0x7F
 353 #if defined(CONFIG_STRIDER_CON) || defined(CONFIG_STRIDER_CON_DP)
 354 #define I2C_SOFT_DECLARATIONS5
 355 #define CONFIG_SYS_I2C_SOFT_SPEED_5             50000
 356 #define CONFIG_SYS_I2C_SOFT_SLAVE_5             0x7F
 357 #define I2C_SOFT_DECLARATIONS6
 358 #define CONFIG_SYS_I2C_SOFT_SPEED_6             50000
 359 #define CONFIG_SYS_I2C_SOFT_SLAVE_6             0x7F
 360 #define I2C_SOFT_DECLARATIONS7
 361 #define CONFIG_SYS_I2C_SOFT_SPEED_7             50000
 362 #define CONFIG_SYS_I2C_SOFT_SLAVE_7             0x7F
 363 #define I2C_SOFT_DECLARATIONS8
 364 #define CONFIG_SYS_I2C_SOFT_SPEED_8             50000
 365 #define CONFIG_SYS_I2C_SOFT_SLAVE_8             0x7F
 366 #endif
 367 #ifdef CONFIG_STRIDER_CON_DP
 368 #define I2C_SOFT_DECLARATIONS9
 369 #define CONFIG_SYS_I2C_SOFT_SPEED_9             50000
 370 #define CONFIG_SYS_I2C_SOFT_SLAVE_9             0x7F
 371 #define I2C_SOFT_DECLARATIONS10
 372 #define CONFIG_SYS_I2C_SOFT_SPEED_10            50000
 373 #define CONFIG_SYS_I2C_SOFT_SLAVE_10            0x7F
 374 #define I2C_SOFT_DECLARATIONS11
 375 #define CONFIG_SYS_I2C_SOFT_SPEED_11            50000
 376 #define CONFIG_SYS_I2C_SOFT_SLAVE_11            0x7F
 377 #define I2C_SOFT_DECLARATIONS12
 378 #define CONFIG_SYS_I2C_SOFT_SPEED_12            50000
 379 #define CONFIG_SYS_I2C_SOFT_SLAVE_12            0x7F
 380 #endif
 381
 382 #ifdef CONFIG_STRIDER_CON
 383 #define CONFIG_SYS_ICS8N3QV01_I2C               {5, 6, 7, 8}
 384 #define CONFIG_SYS_CH7301_I2C                   {5, 6, 7, 8}
 385 #define CONFIG_SYS_ADV7611_I2C                  {5, 6, 7, 8}
 386 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 387 #define CONFIG_STRIDER_FANS                     { {10, 0x4c}, {11, 0x4c}, \
 388                                                   {12, 0x4c} }
 389 #elif defined(CONFIG_STRIDER_CON_DP)
 390 #define CONFIG_SYS_ICS8N3QV01_I2C               {13, 14, 15, 16, 17, 18, 19, 20}
 391 #define CONFIG_SYS_CH7301_I2C                   {1, 3, 5, 7}
 392 #define CONFIG_SYS_ADV7611_I2C                  {1, 3, 5, 7}
 393 #define CONFIG_SYS_DP501_I2C                    {1, 3, 5, 7, 2, 4, 6, 8}
 394 #define CONFIG_STRIDER_FANS                     { {10, 0x4c}, {11, 0x4c}, \
 395                                                   {12, 0x4c} }
 396 #elif defined(CONFIG_STRIDER_CPU_DP)
 397 #define CONFIG_SYS_CH7301_I2C                   {1, 2, 3, 4}
 398 #define CONFIG_SYS_ADV7611_I2C                  {1, 2, 3, 4}
 399 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 400 #define CONFIG_STRIDER_FANS                     { {6, 0x4c}, {7, 0x4c}, \
 401                                                   {8, 0x4c} }
 402 #else
 403 #define CONFIG_SYS_CH7301_I2C                   {1, 2, 3, 4}
 404 #define CONFIG_SYS_ADV7611_I2C                  {1, 2, 3, 4}
 405 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 406 #define CONFIG_STRIDER_FANS                     { {2, 0x18}, {3, 0x18}, \
 407                                                   {4, 0x18} }
 408 #endif
 409
 410 #ifndef __ASSEMBLY__
 411 void fpga_gpio_set(unsigned int bus, int pin);
 412 void fpga_gpio_clear(unsigned int bus, int pin);
 413 int fpga_gpio_get(unsigned int bus, int pin);
 414 void fpga_control_set(unsigned int bus, int pin);
 415 void fpga_control_clear(unsigned int bus, int pin);
 416 #endif
 417
 418 #ifdef CONFIG_STRIDER_CON
 419 #define I2C_SDA_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0200 : 0x0040)
 420 #define I2C_SCL_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020)
 421 #define I2C_FPGA_IDX    ((I2C_ADAP_HWNR > 3) ? \
 422                          (I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR)
 423 #elif defined(CONFIG_STRIDER_CON_DP)
 424 #define I2C_SDA_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200)
 425 #define I2C_SCL_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100)
 426 #define I2C_FPGA_IDX    (I2C_ADAP_HWNR % 4)
 427 #else
 428 #define I2C_SDA_GPIO    0x0040
 429 #define I2C_SCL_GPIO    0x0020
 430 #define I2C_FPGA_IDX    I2C_ADAP_HWNR
 431 #endif
 432
 433 #ifdef CONFIG_STRIDER_CON_DP
 434 #define I2C_ACTIVE \
 435         do { \
 436                 if (I2C_ADAP_HWNR > 7) \
 437                         fpga_control_set(I2C_FPGA_IDX, 0x0004); \
 438                 else \
 439                         fpga_control_clear(I2C_FPGA_IDX, 0x0004); \
 440         } while (0)
 441 #else
 442 #define I2C_ACTIVE      { }
 443 #endif
 444
 445 #define I2C_TRISTATE    { }
 446 #define I2C_READ \
 447         (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
 448 #define I2C_SDA(bit) \
 449         do { \
 450                 if (bit) \
 451                         fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \
 452                 else \
 453                         fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \
 454         } while (0)
 455 #define I2C_SCL(bit) \
 456         do { \
 457                 if (bit) \
 458                         fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \
 459                 else \
 460                         fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \
 461         } while (0)
 462 #define I2C_DELAY       udelay(25)      /* 1/4 I2C clock duration */
 463
 464 /*
 465  * Software (bit-bang) MII driver configuration
 466  */
 467 #define CONFIG_BITBANGMII               /* bit-bang MII PHY management */
 468 #define CONFIG_BITBANGMII_MULTI
 469
 470 /*
 471  * OSD Setup
 472  */
 473 #define CONFIG_SYS_OSD_SCREENS          1
 474 #define CONFIG_SYS_DP501_DIFFERENTIAL
 475 #define CONFIG_SYS_DP501_VCAPCTRL0      0x01 /* DDR mode 0, DE for H/VSYNC */
 476
 477 #ifdef CONFIG_STRIDER_CON_DP
 478 #define CONFIG_SYS_OSD_DH
 479 #endif
 480
 481 /*
 482  * General PCI
 483  * Addresses are mapped 1-1.
 484  */
 485 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 486 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
 487 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
 488 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 489 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
 490 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
 491 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 492 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
 493 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 494
 495 /* enable PCIE clock */
 496 #define CONFIG_SYS_SCCR_PCIEXP1CM       1
 497
 498 #define CONFIG_PCI_INDIRECT_BRIDGE
 499 #define CONFIG_PCIE
 500
 501 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 502 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
 503
 504 /*
 505  * TSEC
 506  */
 507 #define CONFIG_TSEC_ENET        /* TSEC ethernet support */
 508 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 509 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 510
 511 /*
 512  * TSEC ethernet configuration
 513  */
 514 #define CONFIG_MII              1 /* MII PHY management */
 515 #define CONFIG_TSEC1
 516 #define CONFIG_TSEC1_NAME       "eTSEC0"
 517 #define TSEC1_PHY_ADDR          1
 518 #define TSEC1_PHYIDX            0
 519 #define TSEC1_FLAGS             0
 520
 521 /* Options are: eTSEC[0-1] */
 522 #define CONFIG_ETHPRIME         "eTSEC0"
 523
 524 /*
 525  * Environment
 526  */
 527 #if 1
 528 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 529                                  CONFIG_SYS_MONITOR_LEN)
 530 #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 531 #define CONFIG_ENV_SIZE         0x2000
 532 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 533 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 534 #else
 535 #define CONFIG_ENV_SIZE         0x2000          /* 8KB */
 536 #endif
 537
 538 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 539 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 540
 541 /*
 542  * Command line configuration.
 543  */
 544
 545 /*
 546  * Miscellaneous configurable options
 547  */
 548 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 549 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms ticks */
 550
 551 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 552
 553 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 554
 555 /*
 556  * For booting Linux, the board info and command line data
 557  * have to be in the first 256 MB of memory, since this is
 558  * the maximum mapped by the Linux kernel during initialization.
 559  */
 560 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 561
 562 /*
 563  * Core HID Setup
 564  */
 565 #define CONFIG_SYS_HID0_INIT    0x000000000
 566 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 567                                  HID0_ENABLE_INSTRUCTION_CACHE | \
 568                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 569 #define CONFIG_SYS_HID2         HID2_HBE
 570
 571 /*
 572  * MMU Setup
 573  */
 574
 575 /* DDR: cache cacheable */
 576 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 577                                         BATL_MEMCOHERENCE)
 578 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
 579                                         BATU_VS | BATU_VP)
 580 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 581 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 582
 583 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
 584 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 585                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 586 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
 587                                         BATU_VP)
 588 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 589 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 590
 591 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 592 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 593                                         BATL_MEMCOHERENCE)
 594 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
 595                                         BATU_VS | BATU_VP)
 596 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 597                                         BATL_CACHEINHIBIT | \
 598                                         BATL_GUARDEDSTORAGE)
 599 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 600
 601 /* Stack in dcache: cacheable, no memory coherence */
 602 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 603 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
 604                                         BATU_VS | BATU_VP)
 605 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 606 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 607
 608 /*
 609  * Environment Configuration
 610  */
 611
 612 #define CONFIG_ENV_OVERWRITE
 613
 614 #if defined(CONFIG_TSEC_ENET)
 615 #define CONFIG_HAS_ETH0
 616 #endif
 617
 618 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 619
 620
 621 #define CONFIG_HOSTNAME         hrcon
 622 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 623 #define CONFIG_BOOTFILE         "uImage"
 624
 625 #define CONFIG_PREBOOT          /* enable preboot variable */
 626
 627 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 628         "netdev=eth0\0"                                                 \
 629         "consoledev=ttyS1\0"                                            \
 630         "u-boot=u-boot.bin\0"                                           \
 631         "kernel_addr=1000000\0"                                 \
 632         "fdt_addr=C00000\0"                                             \
 633         "fdtfile=hrcon.dtb\0"                           \
 634         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 635         "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)      \
 636                 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
 637                 " +${filesize};cp.b ${fileaddr} "                       \
 638                 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"   \
 639         "upd=run load update\0"                                         \
 640
 641 #define CONFIG_NFSBOOTCOMMAND                                           \
 642         "setenv bootargs root=/dev/nfs rw "                             \
 643         "nfsroot=$serverip:$rootpath "                                  \
 644         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 645         "console=$consoledev,$baudrate $othbootargs;"                   \
 646         "tftp ${kernel_addr} $bootfile;"                                \
 647         "tftp ${fdt_addr} $fdtfile;"                                    \
 648         "bootm ${kernel_addr} - ${fdt_addr}"
 649
 650 #define CONFIG_MMCBOOTCOMMAND                                           \
 651         "setenv bootargs root=/dev/mmcblk0p3 rw rootwait "              \
 652         "console=$consoledev,$baudrate $othbootargs;"                   \
 653         "ext2load mmc 0:2 ${kernel_addr} $bootfile;"                    \
 654         "ext2load mmc 0:2 ${fdt_addr} $fdtfile;"                        \
 655         "bootm ${kernel_addr} - ${fdt_addr}"
 656
 657 #define CONFIG_BOOTCOMMAND              CONFIG_MMCBOOTCOMMAND
 658
 659 #endif  /* __CONFIG_H */