include/configs/strider.h

   1 /*
   2  * (C) Copyright 2014
   3  * Dirk Eibach,  Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
   4  *
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15 #define CONFIG_E300             1 /* E300 family */
  16 #define CONFIG_MPC83xx          1 /* MPC83xx family */
  17 #define CONFIG_MPC830x          1 /* MPC830x family */
  18 #define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
  19 #define CONFIG_STRIDER          1 /* STRIDER board specific */
  20
  21 #define CONFIG_FSL_ESDHC
  22 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
  23
  24 /*
  25  * System Clock Setup
  26  */
  27 #define CONFIG_83XX_CLKIN       33333333 /* in Hz */
  28 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
  29
  30 /*
  31  * Hardware Reset Configuration Word
  32  * if CLKIN is 66.66MHz, then
  33  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
  34  * We choose the A type silicon as default, so the core is 400Mhz.
  35  */
  36 #define CONFIG_SYS_HRCW_LOW (\
  37         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  38         HRCWL_DDR_TO_SCB_CLK_2X1 |\
  39         HRCWL_SVCOD_DIV_2 |\
  40         HRCWL_CSB_TO_CLKIN_4X1 |\
  41         HRCWL_CORE_TO_CSB_3X1)
  42 /*
  43  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
  44  * in 8308's HRCWH according to the manual, but original Freescale's
  45  * code has them and I've expirienced some problems using the board
  46  * with BDI3000 attached when I've tried to set these bits to zero
  47  * (UART doesn't work after the 'reset run' command).
  48  */
  49 #define CONFIG_SYS_HRCW_HIGH (\
  50         HRCWH_PCI_HOST |\
  51         HRCWH_PCI1_ARBITER_ENABLE |\
  52         HRCWH_CORE_ENABLE |\
  53         HRCWH_FROM_0XFFF00100 |\
  54         HRCWH_BOOTSEQ_DISABLE |\
  55         HRCWH_SW_WATCHDOG_DISABLE |\
  56         HRCWH_ROM_LOC_LOCAL_16BIT |\
  57         HRCWH_RL_EXT_LEGACY |\
  58         HRCWH_TSEC1M_IN_MII |\
  59         HRCWH_TSEC2M_IN_RGMII |\
  60         HRCWH_BIG_ENDIAN)
  61
  62 /*
  63  * System IO Config
  64  */
  65 #define CONFIG_SYS_SICRH (\
  66         SICRH_ESDHC_A_SD |\
  67         SICRH_ESDHC_B_SD |\
  68         SICRH_ESDHC_C_SD |\
  69         SICRH_GPIO_A_GPIO |\
  70         SICRH_GPIO_B_GPIO |\
  71         SICRH_IEEE1588_A_GPIO |\
  72         SICRH_USB |\
  73         SICRH_GTM_GPIO |\
  74         SICRH_IEEE1588_B_GPIO |\
  75         SICRH_ETSEC2_GPIO |\
  76         SICRH_GPIOSEL_1 |\
  77         SICRH_TMROBI_V3P3 |\
  78         SICRH_TSOBI1_V2P5 |\
  79         SICRH_TSOBI2_V2P5)      /* 0x0037f103 */
  80 #define CONFIG_SYS_SICRL (\
  81         SICRL_SPI_PF0 |\
  82         SICRL_UART_PF0 |\
  83         SICRL_IRQ_PF0 |\
  84         SICRL_I2C2_PF0 |\
  85         SICRL_ETSEC1_TX_CLK)    /* 0x00000000 */
  86
  87 /*
  88  * IMMR new address
  89  */
  90 #define CONFIG_SYS_IMMR         0xE0000000
  91
  92 /*
  93  * SERDES
  94  */
  95 #define CONFIG_FSL_SERDES
  96 #define CONFIG_FSL_SERDES1      0xe3000
  97
  98 /*
  99  * Arbiter Setup
 100  */
 101 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
 102 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
 103 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
 104
 105 /*
 106  * DDR Setup
 107  */
 108 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
 109 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
 110 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
 111 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 112 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 113                                 | DDRCDR_PZ_LOZ \
 114                                 | DDRCDR_NZ_LOZ \
 115                                 | DDRCDR_ODT \
 116                                 | DDRCDR_Q_DRN)
 117                                 /* 0x7b880001 */
 118 /*
 119  * Manually set up DDR parameters
 120  * consist of one chip NT5TU64M16HG from NANYA
 121  */
 122
 123 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
 124
 125 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
 126 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 127                                 | CSCONFIG_ODT_RD_NEVER \
 128                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
 129                                 | CSCONFIG_BANK_BIT_3 \
 130                                 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
 131                                 /* 0x80010102 */
 132 #define CONFIG_SYS_DDR_TIMING_3 0
 133 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
 134                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
 135                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 136                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 137                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 138                                 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 139                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 140                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 141                                 /* 0x00260802 */
 142 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 143                                 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 144                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 145                                 | (7 << TIMING_CFG1_CASLAT_SHIFT) \
 146                                 | (9 << TIMING_CFG1_REFREC_SHIFT) \
 147                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
 148                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 149                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 150                                 /* 0x26279222 */
 151 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
 152                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
 153                                 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 154                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 155                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 156                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 157                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 158                                 /* 0x021848c5 */
 159 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
 160                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 161                                 /* 0x08240100 */
 162 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 163                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 164                                 | SDRAM_CFG_DBW_16)
 165                                 /* 0x43100000 */
 166
 167 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
 168 #define CONFIG_SYS_DDR_MODE             ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
 169                                 | (0x0242 << SDRAM_MODE_SD_SHIFT))
 170                                 /* ODT 150ohm CL=4, AL=0 on SDRAM */
 171 #define CONFIG_SYS_DDR_MODE2            0x00000000
 172
 173 /*
 174  * Memory test
 175  */
 176 #define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
 177 #define CONFIG_SYS_MEMTEST_END          0x07f00000
 178
 179 /*
 180  * The reserved memory
 181  */
 182 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 183
 184 #define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
 185 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 186
 187 /*
 188  * Initial RAM Base Address Setup
 189  */
 190 #define CONFIG_SYS_INIT_RAM_LOCK        1
 191 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 192 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 193 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 194         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 195
 196 /*
 197  * Local Bus Configuration & Clock Setup
 198  */
 199 #define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
 200 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
 201 #define CONFIG_SYS_LBC_LBCR             0x00040000
 202
 203 /*
 204  * FLASH on the Local Bus
 205  */
 206 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 207 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 208 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 209 #define CONFIG_FLASH_CFI_LEGACY
 210 #define CONFIG_SYS_FLASH_LEGACY_512Kx16
 211
 212 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 213 #define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is up to 8M */
 214 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */
 215
 216 /* Window base at flash base */
 217 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 218 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 219
 220 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 221                                 | BR_PS_16      /* 16 bit port */ \
 222                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 223                                 | BR_V)         /* valid */
 224 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 225                                 | OR_UPM_XAM \
 226                                 | OR_GPCM_CSNT \
 227                                 | OR_GPCM_ACS_DIV2 \
 228                                 | OR_GPCM_XACS \
 229                                 | OR_GPCM_SCY_15 \
 230                                 | OR_GPCM_TRLX_SET \
 231                                 | OR_GPCM_EHTR_SET)
 232
 233 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 234 #define CONFIG_SYS_MAX_FLASH_SECT       135
 235
 236 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 237 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 238
 239 /*
 240  * FPGA
 241  */
 242 #define CONFIG_SYS_FPGA0_BASE           0xE0600000
 243 #define CONFIG_SYS_FPGA0_SIZE           1 /* FPGA size is 1M */
 244
 245 /* Window base at FPGA base */
 246 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_FPGA0_BASE
 247 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_1MB)
 248
 249 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FPGA0_BASE \
 250                                 | BR_PS_16      /* 16 bit port */ \
 251                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 252                                 | BR_V)         /* valid */
 253
 254 #define CONFIG_SYS_OR1_PRELIM   (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
 255                                 | OR_UPM_XAM \
 256                                 | OR_GPCM_CSNT \
 257                                 | OR_GPCM_SCY_5 \
 258                                 | OR_GPCM_TRLX_CLEAR \
 259                                 | OR_GPCM_EHTR_CLEAR)
 260
 261 #define CONFIG_SYS_FPGA_BASE(k)         CONFIG_SYS_FPGA0_BASE
 262 #define CONFIG_SYS_FPGA_DONE(k)         0x0010
 263
 264 #define CONFIG_SYS_FPGA_COUNT           1
 265
 266 #define CONFIG_SYS_MCLINK_MAX           3
 267
 268 #define CONFIG_SYS_FPGA_PTR \
 269         { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
 270
 271 #define CONFIG_SYS_FPGA_NO_RFL_HI
 272
 273 /*
 274  * Serial Port
 275  */
 276 #define CONFIG_SYS_NS16550_SERIAL
 277 #define CONFIG_SYS_NS16550_REG_SIZE     1
 278 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 279
 280 #define CONFIG_SYS_BAUDRATE_TABLE  \
 281         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 282
 283 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 284 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 285
 286 /* Pass open firmware flat tree */
 287
 288 /* I2C */
 289 #define CONFIG_SYS_I2C
 290 #define CONFIG_SYS_I2C_FSL
 291 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 292 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 293 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 294
 295 #define CONFIG_PCA953X                  /* NXP PCA9554 */
 296 #define CONFIG_SYS_I2C_PCA953X_WIDTH    { {0x24, 16}, {0x25, 16}, {0x26, 16}, \
 297                                           {0x3c, 8}, {0x3d, 8}, {0x3e, 8} }
 298
 299 #define CONFIG_PCA9698                  /* NXP PCA9698 */
 300
 301 #define CONFIG_SYS_I2C_IHS
 302 #define CONFIG_SYS_I2C_IHS_CH0
 303 #define CONFIG_SYS_I2C_IHS_SPEED_0              50000
 304 #define CONFIG_SYS_I2C_IHS_SLAVE_0              0x7F
 305 #define CONFIG_SYS_I2C_IHS_CH1
 306 #define CONFIG_SYS_I2C_IHS_SPEED_1              50000
 307 #define CONFIG_SYS_I2C_IHS_SLAVE_1              0x7F
 308 #define CONFIG_SYS_I2C_IHS_CH2
 309 #define CONFIG_SYS_I2C_IHS_SPEED_2              50000
 310 #define CONFIG_SYS_I2C_IHS_SLAVE_2              0x7F
 311 #define CONFIG_SYS_I2C_IHS_CH3
 312 #define CONFIG_SYS_I2C_IHS_SPEED_3              50000
 313 #define CONFIG_SYS_I2C_IHS_SLAVE_3              0x7F
 314
 315 #ifdef CONFIG_STRIDER_CON_DP
 316 #define CONFIG_SYS_I2C_IHS_DUAL
 317 #define CONFIG_SYS_I2C_IHS_CH0_1
 318 #define CONFIG_SYS_I2C_IHS_SPEED_0_1            50000
 319 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1            0x7F
 320 #define CONFIG_SYS_I2C_IHS_CH1_1
 321 #define CONFIG_SYS_I2C_IHS_SPEED_1_1            50000
 322 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1            0x7F
 323 #define CONFIG_SYS_I2C_IHS_CH2_1
 324 #define CONFIG_SYS_I2C_IHS_SPEED_2_1            50000
 325 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1            0x7F
 326 #define CONFIG_SYS_I2C_IHS_CH3_1
 327 #define CONFIG_SYS_I2C_IHS_SPEED_3_1            50000
 328 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1            0x7F
 329 #endif
 330
 331 /*
 332  * Software (bit-bang) I2C driver configuration
 333  */
 334 #define CONFIG_SYS_I2C_SOFT
 335 #define CONFIG_SOFT_I2C_READ_REPEATED_START
 336 #define CONFIG_SYS_I2C_SOFT_SPEED               50000
 337 #define CONFIG_SYS_I2C_SOFT_SLAVE               0x7F
 338 #define I2C_SOFT_DECLARATIONS2
 339 #define CONFIG_SYS_I2C_SOFT_SPEED_2             50000
 340 #define CONFIG_SYS_I2C_SOFT_SLAVE_2             0x7F
 341 #define I2C_SOFT_DECLARATIONS3
 342 #define CONFIG_SYS_I2C_SOFT_SPEED_3             50000
 343 #define CONFIG_SYS_I2C_SOFT_SLAVE_3             0x7F
 344 #define I2C_SOFT_DECLARATIONS4
 345 #define CONFIG_SYS_I2C_SOFT_SPEED_4             50000
 346 #define CONFIG_SYS_I2C_SOFT_SLAVE_4             0x7F
 347 #if defined(CONFIG_STRIDER_CON) || defined(CONFIG_STRIDER_CON_DP)
 348 #define I2C_SOFT_DECLARATIONS5
 349 #define CONFIG_SYS_I2C_SOFT_SPEED_5             50000
 350 #define CONFIG_SYS_I2C_SOFT_SLAVE_5             0x7F
 351 #define I2C_SOFT_DECLARATIONS6
 352 #define CONFIG_SYS_I2C_SOFT_SPEED_6             50000
 353 #define CONFIG_SYS_I2C_SOFT_SLAVE_6             0x7F
 354 #define I2C_SOFT_DECLARATIONS7
 355 #define CONFIG_SYS_I2C_SOFT_SPEED_7             50000
 356 #define CONFIG_SYS_I2C_SOFT_SLAVE_7             0x7F
 357 #define I2C_SOFT_DECLARATIONS8
 358 #define CONFIG_SYS_I2C_SOFT_SPEED_8             50000
 359 #define CONFIG_SYS_I2C_SOFT_SLAVE_8             0x7F
 360 #endif
 361 #ifdef CONFIG_STRIDER_CON_DP
 362 #define I2C_SOFT_DECLARATIONS9
 363 #define CONFIG_SYS_I2C_SOFT_SPEED_9             50000
 364 #define CONFIG_SYS_I2C_SOFT_SLAVE_9             0x7F
 365 #define I2C_SOFT_DECLARATIONS10
 366 #define CONFIG_SYS_I2C_SOFT_SPEED_10            50000
 367 #define CONFIG_SYS_I2C_SOFT_SLAVE_10            0x7F
 368 #define I2C_SOFT_DECLARATIONS11
 369 #define CONFIG_SYS_I2C_SOFT_SPEED_11            50000
 370 #define CONFIG_SYS_I2C_SOFT_SLAVE_11            0x7F
 371 #define I2C_SOFT_DECLARATIONS12
 372 #define CONFIG_SYS_I2C_SOFT_SPEED_12            50000
 373 #define CONFIG_SYS_I2C_SOFT_SLAVE_12            0x7F
 374 #endif
 375
 376 #ifdef CONFIG_STRIDER_CON
 377 #define CONFIG_SYS_ICS8N3QV01_I2C               {5, 6, 7, 8}
 378 #define CONFIG_SYS_CH7301_I2C                   {5, 6, 7, 8}
 379 #define CONFIG_SYS_ADV7611_I2C                  {5, 6, 7, 8}
 380 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 381 #define CONFIG_STRIDER_FANS                     { {10, 0x4c}, {11, 0x4c}, \
 382                                                   {12, 0x4c} }
 383 #elif defined(CONFIG_STRIDER_CON_DP)
 384 #define CONFIG_SYS_ICS8N3QV01_I2C               {13, 14, 15, 16, 17, 18, 19, 20}
 385 #define CONFIG_SYS_CH7301_I2C                   {1, 3, 5, 7}
 386 #define CONFIG_SYS_ADV7611_I2C                  {1, 3, 5, 7}
 387 #define CONFIG_SYS_DP501_I2C                    {1, 3, 5, 7, 2, 4, 6, 8}
 388 #define CONFIG_STRIDER_FANS                     { {10, 0x4c}, {11, 0x4c}, \
 389                                                   {12, 0x4c} }
 390 #elif defined(CONFIG_STRIDER_CPU_DP)
 391 #define CONFIG_SYS_CH7301_I2C                   {1, 2, 3, 4}
 392 #define CONFIG_SYS_ADV7611_I2C                  {1, 2, 3, 4}
 393 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 394 #define CONFIG_STRIDER_FANS                     { {6, 0x4c}, {7, 0x4c}, \
 395                                                   {8, 0x4c} }
 396 #else
 397 #define CONFIG_SYS_CH7301_I2C                   {1, 2, 3, 4}
 398 #define CONFIG_SYS_ADV7611_I2C                  {1, 2, 3, 4}
 399 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 400 #define CONFIG_STRIDER_FANS                     { {2, 0x18}, {3, 0x18}, \
 401                                                   {4, 0x18} }
 402 #endif
 403
 404 #ifndef __ASSEMBLY__
 405 void fpga_gpio_set(unsigned int bus, int pin);
 406 void fpga_gpio_clear(unsigned int bus, int pin);
 407 int fpga_gpio_get(unsigned int bus, int pin);
 408 void fpga_control_set(unsigned int bus, int pin);
 409 void fpga_control_clear(unsigned int bus, int pin);
 410 #endif
 411
 412 #ifdef CONFIG_STRIDER_CON
 413 #define I2C_SDA_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0200 : 0x0040)
 414 #define I2C_SCL_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020)
 415 #define I2C_FPGA_IDX    ((I2C_ADAP_HWNR > 3) ? \
 416                          (I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR)
 417 #elif defined(CONFIG_STRIDER_CON_DP)
 418 #define I2C_SDA_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200)
 419 #define I2C_SCL_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100)
 420 #define I2C_FPGA_IDX    (I2C_ADAP_HWNR % 4)
 421 #else
 422 #define I2C_SDA_GPIO    0x0040
 423 #define I2C_SCL_GPIO    0x0020
 424 #define I2C_FPGA_IDX    I2C_ADAP_HWNR
 425 #endif
 426
 427 #ifdef CONFIG_STRIDER_CON_DP
 428 #define I2C_ACTIVE \
 429         do { \
 430                 if (I2C_ADAP_HWNR > 7) \
 431                         fpga_control_set(I2C_FPGA_IDX, 0x0004); \
 432                 else \
 433                         fpga_control_clear(I2C_FPGA_IDX, 0x0004); \
 434         } while (0)
 435 #else
 436 #define I2C_ACTIVE      { }
 437 #endif
 438
 439 #define I2C_TRISTATE    { }
 440 #define I2C_READ \
 441         (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
 442 #define I2C_SDA(bit) \
 443         do { \
 444                 if (bit) \
 445                         fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \
 446                 else \
 447                         fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \
 448         } while (0)
 449 #define I2C_SCL(bit) \
 450         do { \
 451                 if (bit) \
 452                         fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \
 453                 else \
 454                         fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \
 455         } while (0)
 456 #define I2C_DELAY       udelay(25)      /* 1/4 I2C clock duration */
 457
 458 /*
 459  * Software (bit-bang) MII driver configuration
 460  */
 461 #define CONFIG_BITBANGMII               /* bit-bang MII PHY management */
 462 #define CONFIG_BITBANGMII_MULTI
 463
 464 /*
 465  * OSD Setup
 466  */
 467 #define CONFIG_SYS_OSD_SCREENS          1
 468 #define CONFIG_SYS_DP501_DIFFERENTIAL
 469 #define CONFIG_SYS_DP501_VCAPCTRL0      0x01 /* DDR mode 0, DE for H/VSYNC */
 470
 471 #ifdef CONFIG_STRIDER_CON_DP
 472 #define CONFIG_SYS_OSD_DH
 473 #endif
 474
 475 /*
 476  * General PCI
 477  * Addresses are mapped 1-1.
 478  */
 479 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 480 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
 481 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
 482 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 483 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
 484 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
 485 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 486 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
 487 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 488
 489 /* enable PCIE clock */
 490 #define CONFIG_SYS_SCCR_PCIEXP1CM       1
 491
 492 #define CONFIG_PCI_INDIRECT_BRIDGE
 493 #define CONFIG_PCIE
 494
 495 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 496 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
 497
 498 /*
 499  * TSEC
 500  */
 501 #define CONFIG_TSEC_ENET        /* TSEC ethernet support */
 502 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 503 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 504
 505 /*
 506  * TSEC ethernet configuration
 507  */
 508 #define CONFIG_MII              1 /* MII PHY management */
 509 #define CONFIG_TSEC1
 510 #define CONFIG_TSEC1_NAME       "eTSEC0"
 511 #define TSEC1_PHY_ADDR          1
 512 #define TSEC1_PHYIDX            0
 513 #define TSEC1_FLAGS             0
 514
 515 /* Options are: eTSEC[0-1] */
 516 #define CONFIG_ETHPRIME         "eTSEC0"
 517
 518 /*
 519  * Environment
 520  */
 521 #if 1
 522 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 523                                  CONFIG_SYS_MONITOR_LEN)
 524 #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 525 #define CONFIG_ENV_SIZE         0x2000
 526 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 527 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 528 #else
 529 #define CONFIG_ENV_SIZE         0x2000          /* 8KB */
 530 #endif
 531
 532 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 533 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 534
 535 /*
 536  * Command line configuration.
 537  */
 538
 539 /*
 540  * Miscellaneous configurable options
 541  */
 542 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 543 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms ticks */
 544
 545 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 546
 547 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 548
 549 /*
 550  * For booting Linux, the board info and command line data
 551  * have to be in the first 256 MB of memory, since this is
 552  * the maximum mapped by the Linux kernel during initialization.
 553  */
 554 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 555
 556 /*
 557  * Core HID Setup
 558  */
 559 #define CONFIG_SYS_HID0_INIT    0x000000000
 560 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 561                                  HID0_ENABLE_INSTRUCTION_CACHE | \
 562                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 563 #define CONFIG_SYS_HID2         HID2_HBE
 564
 565 /*
 566  * MMU Setup
 567  */
 568
 569 /* DDR: cache cacheable */
 570 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 571                                         BATL_MEMCOHERENCE)
 572 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
 573                                         BATU_VS | BATU_VP)
 574 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 575 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 576
 577 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
 578 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 579                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 580 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
 581                                         BATU_VP)
 582 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 583 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 584
 585 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 586 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 587                                         BATL_MEMCOHERENCE)
 588 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
 589                                         BATU_VS | BATU_VP)
 590 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 591                                         BATL_CACHEINHIBIT | \
 592                                         BATL_GUARDEDSTORAGE)
 593 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 594
 595 /* Stack in dcache: cacheable, no memory coherence */
 596 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 597 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
 598                                         BATU_VS | BATU_VP)
 599 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 600 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 601
 602 /*
 603  * Environment Configuration
 604  */
 605
 606 #define CONFIG_ENV_OVERWRITE
 607
 608 #if defined(CONFIG_TSEC_ENET)
 609 #define CONFIG_HAS_ETH0
 610 #endif
 611
 612 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 613
 614
 615 #define CONFIG_HOSTNAME         hrcon
 616 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 617 #define CONFIG_BOOTFILE         "uImage"
 618
 619 #define CONFIG_PREBOOT          /* enable preboot variable */
 620
 621 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 622         "netdev=eth0\0"                                                 \
 623         "consoledev=ttyS1\0"                                            \
 624         "u-boot=u-boot.bin\0"                                           \
 625         "kernel_addr=1000000\0"                                 \
 626         "fdt_addr=C00000\0"                                             \
 627         "fdtfile=hrcon.dtb\0"                           \
 628         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 629         "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)      \
 630                 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
 631                 " +${filesize};cp.b ${fileaddr} "                       \
 632                 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"   \
 633         "upd=run load update\0"                                         \
 634
 635 #define CONFIG_NFSBOOTCOMMAND                                           \
 636         "setenv bootargs root=/dev/nfs rw "                             \
 637         "nfsroot=$serverip:$rootpath "                                  \
 638         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 639         "console=$consoledev,$baudrate $othbootargs;"                   \
 640         "tftp ${kernel_addr} $bootfile;"                                \
 641         "tftp ${fdt_addr} $fdtfile;"                                    \
 642         "bootm ${kernel_addr} - ${fdt_addr}"
 643
 644 #define CONFIG_MMCBOOTCOMMAND                                           \
 645         "setenv bootargs root=/dev/mmcblk0p3 rw rootwait "              \
 646         "console=$consoledev,$baudrate $othbootargs;"                   \
 647         "ext2load mmc 0:2 ${kernel_addr} $bootfile;"                    \
 648         "ext2load mmc 0:2 ${fdt_addr} $fdtfile;"                        \
 649         "bootm ${kernel_addr} - ${fdt_addr}"
 650
 651 #define CONFIG_BOOTCOMMAND              CONFIG_MMCBOOTCOMMAND
 652
 653 #endif  /* __CONFIG_H */