include/configs/strider.h

   1 /*
   2  * (C) Copyright 2014
   3  * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
   4  *
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15 #define CONFIG_E300             1 /* E300 family */
  16 #define CONFIG_MPC83xx          1 /* MPC83xx family */
  17 #define CONFIG_MPC830x          1 /* MPC830x family */
  18 #define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
  19 #define CONFIG_STRIDER          1 /* STRIDER board specific */
  20
  21 #define CONFIG_SYS_TEXT_BASE    0xFE000000
  22
  23 #define CONFIG_BOARD_EARLY_INIT_F
  24 #define CONFIG_BOARD_EARLY_INIT_R
  25 #define CONFIG_LAST_STAGE_INIT
  26
  27 #define CONFIG_FSL_ESDHC
  28 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
  29 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
  30
  31 #define CONFIG_GENERIC_MMC
  32 #define CONFIG_DOS_PARTITION
  33
  34 #define CONFIG_SYS_ALT_MEMTEST
  35
  36 #define CONFIG_CMD_FPGAD
  37 #define CONFIG_CMD_IOLOOP
  38
  39 /*
  40  * System Clock Setup
  41  */
  42 #define CONFIG_83XX_CLKIN       33333333 /* in Hz */
  43 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
  44
  45 /*
  46  * Hardware Reset Configuration Word
  47  * if CLKIN is 66.66MHz, then
  48  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
  49  * We choose the A type silicon as default, so the core is 400Mhz.
  50  */
  51 #define CONFIG_SYS_HRCW_LOW (\
  52         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  53         HRCWL_DDR_TO_SCB_CLK_2X1 |\
  54         HRCWL_SVCOD_DIV_2 |\
  55         HRCWL_CSB_TO_CLKIN_4X1 |\
  56         HRCWL_CORE_TO_CSB_3X1)
  57 /*
  58  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
  59  * in 8308's HRCWH according to the manual, but original Freescale's
  60  * code has them and I've expirienced some problems using the board
  61  * with BDI3000 attached when I've tried to set these bits to zero
  62  * (UART doesn't work after the 'reset run' command).
  63  */
  64 #define CONFIG_SYS_HRCW_HIGH (\
  65         HRCWH_PCI_HOST |\
  66         HRCWH_PCI1_ARBITER_ENABLE |\
  67         HRCWH_CORE_ENABLE |\
  68         HRCWH_FROM_0XFFF00100 |\
  69         HRCWH_BOOTSEQ_DISABLE |\
  70         HRCWH_SW_WATCHDOG_DISABLE |\
  71         HRCWH_ROM_LOC_LOCAL_16BIT |\
  72         HRCWH_RL_EXT_LEGACY |\
  73         HRCWH_TSEC1M_IN_MII |\
  74         HRCWH_TSEC2M_IN_RGMII |\
  75         HRCWH_BIG_ENDIAN)
  76
  77 /*
  78  * System IO Config
  79  */
  80 #define CONFIG_SYS_SICRH (\
  81         SICRH_ESDHC_A_SD |\
  82         SICRH_ESDHC_B_SD |\
  83         SICRH_ESDHC_C_SD |\
  84         SICRH_GPIO_A_GPIO |\
  85         SICRH_GPIO_B_GPIO |\
  86         SICRH_IEEE1588_A_GPIO |\
  87         SICRH_USB |\
  88         SICRH_GTM_GPIO |\
  89         SICRH_IEEE1588_B_GPIO |\
  90         SICRH_ETSEC2_GPIO |\
  91         SICRH_GPIOSEL_1 |\
  92         SICRH_TMROBI_V3P3 |\
  93         SICRH_TSOBI1_V2P5 |\
  94         SICRH_TSOBI2_V2P5)      /* 0x0037f103 */
  95 #define CONFIG_SYS_SICRL (\
  96         SICRL_SPI_PF0 |\
  97         SICRL_UART_PF0 |\
  98         SICRL_IRQ_PF0 |\
  99         SICRL_I2C2_PF0 |\
 100         SICRL_ETSEC1_TX_CLK)    /* 0x00000000 */
 101
 102 /*
 103  * IMMR new address
 104  */
 105 #define CONFIG_SYS_IMMR         0xE0000000
 106
 107 /*
 108  * SERDES
 109  */
 110 #define CONFIG_FSL_SERDES
 111 #define CONFIG_FSL_SERDES1      0xe3000
 112
 113 /*
 114  * Arbiter Setup
 115  */
 116 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
 117 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
 118 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
 119
 120 /*
 121  * DDR Setup
 122  */
 123 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
 124 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
 125 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
 126 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 127 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 128                                 | DDRCDR_PZ_LOZ \
 129                                 | DDRCDR_NZ_LOZ \
 130                                 | DDRCDR_ODT \
 131                                 | DDRCDR_Q_DRN)
 132                                 /* 0x7b880001 */
 133 /*
 134  * Manually set up DDR parameters
 135  * consist of one chip NT5TU64M16HG from NANYA
 136  */
 137
 138 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
 139
 140 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
 141 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 142                                 | CSCONFIG_ODT_RD_NEVER \
 143                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
 144                                 | CSCONFIG_BANK_BIT_3 \
 145                                 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
 146                                 /* 0x80010102 */
 147 #define CONFIG_SYS_DDR_TIMING_3 0
 148 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
 149                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
 150                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 151                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 152                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 153                                 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 154                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 155                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 156                                 /* 0x00260802 */
 157 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 158                                 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 159                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 160                                 | (7 << TIMING_CFG1_CASLAT_SHIFT) \
 161                                 | (9 << TIMING_CFG1_REFREC_SHIFT) \
 162                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
 163                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 164                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 165                                 /* 0x26279222 */
 166 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
 167                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
 168                                 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 169                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 170                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 171                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 172                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 173                                 /* 0x021848c5 */
 174 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
 175                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 176                                 /* 0x08240100 */
 177 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 178                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 179                                 | SDRAM_CFG_DBW_16)
 180                                 /* 0x43100000 */
 181
 182 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
 183 #define CONFIG_SYS_DDR_MODE             ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
 184                                 | (0x0242 << SDRAM_MODE_SD_SHIFT))
 185                                 /* ODT 150ohm CL=4, AL=0 on SDRAM */
 186 #define CONFIG_SYS_DDR_MODE2            0x00000000
 187
 188 /*
 189  * Memory test
 190  */
 191 #define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
 192 #define CONFIG_SYS_MEMTEST_END          0x07f00000
 193
 194 /*
 195  * The reserved memory
 196  */
 197 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 198
 199 #define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
 200 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 201
 202 /*
 203  * Initial RAM Base Address Setup
 204  */
 205 #define CONFIG_SYS_INIT_RAM_LOCK        1
 206 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 207 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 208 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 209         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 210
 211 /*
 212  * Local Bus Configuration & Clock Setup
 213  */
 214 #define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
 215 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
 216 #define CONFIG_SYS_LBC_LBCR             0x00040000
 217
 218 /*
 219  * FLASH on the Local Bus
 220  */
 221 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 222 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 223 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 224 #define CONFIG_FLASH_CFI_LEGACY
 225 #define CONFIG_SYS_FLASH_LEGACY_512Kx16
 226
 227 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 228 #define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is up to 8M */
 229 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */
 230
 231 /* Window base at flash base */
 232 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 233 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 234
 235 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 236                                 | BR_PS_16      /* 16 bit port */ \
 237                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 238                                 | BR_V)         /* valid */
 239 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 240                                 | OR_UPM_XAM \
 241                                 | OR_GPCM_CSNT \
 242                                 | OR_GPCM_ACS_DIV2 \
 243                                 | OR_GPCM_XACS \
 244                                 | OR_GPCM_SCY_15 \
 245                                 | OR_GPCM_TRLX_SET \
 246                                 | OR_GPCM_EHTR_SET)
 247
 248 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 249 #define CONFIG_SYS_MAX_FLASH_SECT       135
 250
 251 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 252 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 253
 254 /*
 255  * FPGA
 256  */
 257 #define CONFIG_SYS_FPGA0_BASE           0xE0600000
 258 #define CONFIG_SYS_FPGA0_SIZE           1 /* FPGA size is 1M */
 259
 260 /* Window base at FPGA base */
 261 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_FPGA0_BASE
 262 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_1MB)
 263
 264 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FPGA0_BASE \
 265                                 | BR_PS_16      /* 16 bit port */ \
 266                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 267                                 | BR_V)         /* valid */
 268
 269 #define CONFIG_SYS_OR1_PRELIM   (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
 270                                 | OR_UPM_XAM \
 271                                 | OR_GPCM_CSNT \
 272                                 | OR_GPCM_SCY_5 \
 273                                 | OR_GPCM_TRLX_CLEAR \
 274                                 | OR_GPCM_EHTR_CLEAR)
 275
 276 #define CONFIG_SYS_FPGA_BASE(k)         CONFIG_SYS_FPGA0_BASE
 277 #define CONFIG_SYS_FPGA_DONE(k)         0x0010
 278
 279 #define CONFIG_SYS_FPGA_COUNT           1
 280
 281 #define CONFIG_SYS_MCLINK_MAX           3
 282
 283 #define CONFIG_SYS_FPGA_PTR \
 284         { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
 285
 286 #define CONFIG_SYS_FPGA_NO_RFL_HI
 287
 288 /*
 289  * Serial Port
 290  */
 291 #define CONFIG_CONS_INDEX       2
 292 #define CONFIG_SYS_NS16550_SERIAL
 293 #define CONFIG_SYS_NS16550_REG_SIZE     1
 294 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 295
 296 #define CONFIG_SYS_BAUDRATE_TABLE  \
 297         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 298
 299 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 300 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 301
 302 /* Pass open firmware flat tree */
 303
 304 /* I2C */
 305 #define CONFIG_SYS_I2C
 306 #define CONFIG_SYS_I2C_FSL
 307 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 308 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 309 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 310
 311 #define CONFIG_PCA953X                  /* NXP PCA9554 */
 312 #define CONFIG_CMD_PCA953X
 313 #define CONFIG_CMD_PCA953X_INFO
 314 #define CONFIG_SYS_I2C_PCA953X_WIDTH    { {0x24, 16}, {0x25, 16}, {0x26, 16}, \
 315                                           {0x3c, 8}, {0x3d, 8}, {0x3e, 8} }
 316
 317 #define CONFIG_PCA9698                  /* NXP PCA9698 */
 318
 319 #define CONFIG_SYS_I2C_IHS
 320 #define CONFIG_SYS_I2C_IHS_CH0
 321 #define CONFIG_SYS_I2C_IHS_SPEED_0              50000
 322 #define CONFIG_SYS_I2C_IHS_SLAVE_0              0x7F
 323 #define CONFIG_SYS_I2C_IHS_CH1
 324 #define CONFIG_SYS_I2C_IHS_SPEED_1              50000
 325 #define CONFIG_SYS_I2C_IHS_SLAVE_1              0x7F
 326 #define CONFIG_SYS_I2C_IHS_CH2
 327 #define CONFIG_SYS_I2C_IHS_SPEED_2              50000
 328 #define CONFIG_SYS_I2C_IHS_SLAVE_2              0x7F
 329 #define CONFIG_SYS_I2C_IHS_CH3
 330 #define CONFIG_SYS_I2C_IHS_SPEED_3              50000
 331 #define CONFIG_SYS_I2C_IHS_SLAVE_3              0x7F
 332
 333 #ifdef CONFIG_STRIDER_CON_DP
 334 #define CONFIG_SYS_I2C_IHS_DUAL
 335 #define CONFIG_SYS_I2C_IHS_CH0_1
 336 #define CONFIG_SYS_I2C_IHS_SPEED_0_1            50000
 337 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1            0x7F
 338 #define CONFIG_SYS_I2C_IHS_CH1_1
 339 #define CONFIG_SYS_I2C_IHS_SPEED_1_1            50000
 340 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1            0x7F
 341 #define CONFIG_SYS_I2C_IHS_CH2_1
 342 #define CONFIG_SYS_I2C_IHS_SPEED_2_1            50000
 343 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1            0x7F
 344 #define CONFIG_SYS_I2C_IHS_CH3_1
 345 #define CONFIG_SYS_I2C_IHS_SPEED_3_1            50000
 346 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1            0x7F
 347 #endif
 348
 349 /*
 350  * Software (bit-bang) I2C driver configuration
 351  */
 352 #define CONFIG_SYS_I2C_SOFT
 353 #define CONFIG_SOFT_I2C_READ_REPEATED_START
 354 #define CONFIG_SYS_I2C_SOFT_SPEED               50000
 355 #define CONFIG_SYS_I2C_SOFT_SLAVE               0x7F
 356 #define I2C_SOFT_DECLARATIONS2
 357 #define CONFIG_SYS_I2C_SOFT_SPEED_2             50000
 358 #define CONFIG_SYS_I2C_SOFT_SLAVE_2             0x7F
 359 #define I2C_SOFT_DECLARATIONS3
 360 #define CONFIG_SYS_I2C_SOFT_SPEED_3             50000
 361 #define CONFIG_SYS_I2C_SOFT_SLAVE_3             0x7F
 362 #define I2C_SOFT_DECLARATIONS4
 363 #define CONFIG_SYS_I2C_SOFT_SPEED_4             50000
 364 #define CONFIG_SYS_I2C_SOFT_SLAVE_4             0x7F
 365 #if defined(CONFIG_STRIDER_CON) || defined(CONFIG_STRIDER_CON_DP)
 366 #define I2C_SOFT_DECLARATIONS5
 367 #define CONFIG_SYS_I2C_SOFT_SPEED_5             50000
 368 #define CONFIG_SYS_I2C_SOFT_SLAVE_5             0x7F
 369 #define I2C_SOFT_DECLARATIONS6
 370 #define CONFIG_SYS_I2C_SOFT_SPEED_6             50000
 371 #define CONFIG_SYS_I2C_SOFT_SLAVE_6             0x7F
 372 #define I2C_SOFT_DECLARATIONS7
 373 #define CONFIG_SYS_I2C_SOFT_SPEED_7             50000
 374 #define CONFIG_SYS_I2C_SOFT_SLAVE_7             0x7F
 375 #define I2C_SOFT_DECLARATIONS8
 376 #define CONFIG_SYS_I2C_SOFT_SPEED_8             50000
 377 #define CONFIG_SYS_I2C_SOFT_SLAVE_8             0x7F
 378 #endif
 379 #ifdef CONFIG_STRIDER_CON_DP
 380 #define I2C_SOFT_DECLARATIONS9
 381 #define CONFIG_SYS_I2C_SOFT_SPEED_9             50000
 382 #define CONFIG_SYS_I2C_SOFT_SLAVE_9             0x7F
 383 #define I2C_SOFT_DECLARATIONS10
 384 #define CONFIG_SYS_I2C_SOFT_SPEED_10            50000
 385 #define CONFIG_SYS_I2C_SOFT_SLAVE_10            0x7F
 386 #define I2C_SOFT_DECLARATIONS11
 387 #define CONFIG_SYS_I2C_SOFT_SPEED_11            50000
 388 #define CONFIG_SYS_I2C_SOFT_SLAVE_11            0x7F
 389 #define I2C_SOFT_DECLARATIONS12
 390 #define CONFIG_SYS_I2C_SOFT_SPEED_12            50000
 391 #define CONFIG_SYS_I2C_SOFT_SLAVE_12            0x7F
 392 #endif
 393
 394 #ifdef CONFIG_STRIDER_CON
 395 #define CONFIG_SYS_ICS8N3QV01_I2C               {5, 6, 7, 8}
 396 #define CONFIG_SYS_CH7301_I2C                   {5, 6, 7, 8}
 397 #define CONFIG_SYS_ADV7611_I2C                  {5, 6, 7, 8}
 398 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 399 #define CONFIG_STRIDER_FANS                     { {10, 0x4c}, {11, 0x4c}, \
 400                                                   {12, 0x4c} }
 401 #elif defined(CONFIG_STRIDER_CON_DP)
 402 #define CONFIG_SYS_ICS8N3QV01_I2C               {13, 14, 15, 16, 17, 18, 19, 20}
 403 #define CONFIG_SYS_CH7301_I2C                   {1, 3, 5, 7}
 404 #define CONFIG_SYS_ADV7611_I2C                  {1, 3, 5, 7}
 405 #define CONFIG_SYS_DP501_I2C                    {1, 3, 5, 7, 2, 4, 6, 8}
 406 #define CONFIG_STRIDER_FANS                     { {10, 0x4c}, {11, 0x4c}, \
 407                                                   {12, 0x4c} }
 408 #elif defined(CONFIG_STRIDER_CPU_DP)
 409 #define CONFIG_SYS_CH7301_I2C                   {1, 2, 3, 4}
 410 #define CONFIG_SYS_ADV7611_I2C                  {1, 2, 3, 4}
 411 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 412 #define CONFIG_STRIDER_FANS                     { {6, 0x4c}, {7, 0x4c}, \
 413                                                   {8, 0x4c} }
 414 #else
 415 #define CONFIG_SYS_CH7301_I2C                   {1, 2, 3, 4}
 416 #define CONFIG_SYS_ADV7611_I2C                  {1, 2, 3, 4}
 417 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 418 #define CONFIG_STRIDER_FANS                     { {2, 0x18}, {3, 0x18}, \
 419                                                   {4, 0x18} }
 420 #endif
 421
 422 #ifndef __ASSEMBLY__
 423 void fpga_gpio_set(unsigned int bus, int pin);
 424 void fpga_gpio_clear(unsigned int bus, int pin);
 425 int fpga_gpio_get(unsigned int bus, int pin);
 426 void fpga_control_set(unsigned int bus, int pin);
 427 void fpga_control_clear(unsigned int bus, int pin);
 428 #endif
 429
 430 #ifdef CONFIG_STRIDER_CON
 431 #define I2C_SDA_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0200 : 0x0040)
 432 #define I2C_SCL_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020)
 433 #define I2C_FPGA_IDX    ((I2C_ADAP_HWNR > 3) ? \
 434                          (I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR)
 435 #elif defined(CONFIG_STRIDER_CON_DP)
 436 #define I2C_SDA_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200)
 437 #define I2C_SCL_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100)
 438 #define I2C_FPGA_IDX    (I2C_ADAP_HWNR % 4)
 439 #else
 440 #define I2C_SDA_GPIO    0x0040
 441 #define I2C_SCL_GPIO    0x0020
 442 #define I2C_FPGA_IDX    I2C_ADAP_HWNR
 443 #endif
 444
 445 #ifdef CONFIG_STRIDER_CON_DP
 446 #define I2C_ACTIVE \
 447         do { \
 448                 if (I2C_ADAP_HWNR > 7) \
 449                         fpga_control_set(I2C_FPGA_IDX, 0x0004); \
 450                 else \
 451                         fpga_control_clear(I2C_FPGA_IDX, 0x0004); \
 452         } while (0)
 453 #else
 454 #define I2C_ACTIVE      { }
 455 #endif
 456
 457 #define I2C_TRISTATE    { }
 458 #define I2C_READ \
 459         (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
 460 #define I2C_SDA(bit) \
 461         do { \
 462                 if (bit) \
 463                         fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \
 464                 else \
 465                         fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \
 466         } while (0)
 467 #define I2C_SCL(bit) \
 468         do { \
 469                 if (bit) \
 470                         fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \
 471                 else \
 472                         fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \
 473         } while (0)
 474 #define I2C_DELAY       udelay(25)      /* 1/4 I2C clock duration */
 475
 476 /*
 477  * Software (bit-bang) MII driver configuration
 478  */
 479 #define CONFIG_BITBANGMII               /* bit-bang MII PHY management */
 480 #define CONFIG_BITBANGMII_MULTI
 481
 482 /*
 483  * OSD Setup
 484  */
 485 #define CONFIG_SYS_OSD_SCREENS          1
 486 #define CONFIG_SYS_DP501_DIFFERENTIAL
 487 #define CONFIG_SYS_DP501_VCAPCTRL0      0x01 /* DDR mode 0, DE for H/VSYNC */
 488
 489 #ifdef CONFIG_STRIDER_CON_DP
 490 #define CONFIG_SYS_OSD_DH
 491 #endif
 492
 493 /*
 494  * General PCI
 495  * Addresses are mapped 1-1.
 496  */
 497 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 498 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
 499 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
 500 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 501 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
 502 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
 503 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 504 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
 505 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 506
 507 /* enable PCIE clock */
 508 #define CONFIG_SYS_SCCR_PCIEXP1CM       1
 509
 510 #define CONFIG_PCI_INDIRECT_BRIDGE
 511 #define CONFIG_PCIE
 512
 513 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 514 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
 515
 516 /*
 517  * TSEC
 518  */
 519 #define CONFIG_TSEC_ENET        /* TSEC ethernet support */
 520 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 521 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 522
 523 /*
 524  * TSEC ethernet configuration
 525  */
 526 #define CONFIG_MII              1 /* MII PHY management */
 527 #define CONFIG_TSEC1
 528 #define CONFIG_TSEC1_NAME       "eTSEC0"
 529 #define TSEC1_PHY_ADDR          1
 530 #define TSEC1_PHYIDX            0
 531 #define TSEC1_FLAGS             0
 532
 533 /* Options are: eTSEC[0-1] */
 534 #define CONFIG_ETHPRIME         "eTSEC0"
 535
 536 /*
 537  * Environment
 538  */
 539 #if 1
 540 #define CONFIG_ENV_IS_IN_FLASH  1
 541 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 542                                  CONFIG_SYS_MONITOR_LEN)
 543 #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 544 #define CONFIG_ENV_SIZE         0x2000
 545 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 546 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 547 #else
 548 #define CONFIG_ENV_IS_NOWHERE
 549 #define CONFIG_ENV_SIZE         0x2000          /* 8KB */
 550 #endif
 551
 552 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 553 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 554
 555 /*
 556  * Command line configuration.
 557  */
 558 #define CONFIG_CMD_PCI
 559
 560 #define CONFIG_CMDLINE_EDITING  1       /* add command line history */
 561 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
 562
 563 /*
 564  * Miscellaneous configurable options
 565  */
 566 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 567 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 568 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms ticks */
 569
 570 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 571
 572 /* Print Buffer Size */
 573 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 574 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 575 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 576
 577 /*
 578  * For booting Linux, the board info and command line data
 579  * have to be in the first 256 MB of memory, since this is
 580  * the maximum mapped by the Linux kernel during initialization.
 581  */
 582 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 583
 584 /*
 585  * Core HID Setup
 586  */
 587 #define CONFIG_SYS_HID0_INIT    0x000000000
 588 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 589                                  HID0_ENABLE_INSTRUCTION_CACHE | \
 590                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 591 #define CONFIG_SYS_HID2         HID2_HBE
 592
 593 /*
 594  * MMU Setup
 595  */
 596
 597 /* DDR: cache cacheable */
 598 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 599                                         BATL_MEMCOHERENCE)
 600 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
 601                                         BATU_VS | BATU_VP)
 602 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 603 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 604
 605 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
 606 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 607                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 608 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
 609                                         BATU_VP)
 610 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 611 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 612
 613 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 614 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 615                                         BATL_MEMCOHERENCE)
 616 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
 617                                         BATU_VS | BATU_VP)
 618 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 619                                         BATL_CACHEINHIBIT | \
 620                                         BATL_GUARDEDSTORAGE)
 621 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 622
 623 /* Stack in dcache: cacheable, no memory coherence */
 624 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 625 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
 626                                         BATU_VS | BATU_VP)
 627 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 628 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 629
 630 /*
 631  * Environment Configuration
 632  */
 633
 634 #define CONFIG_ENV_OVERWRITE
 635
 636 #if defined(CONFIG_TSEC_ENET)
 637 #define CONFIG_HAS_ETH0
 638 #endif
 639
 640 #define CONFIG_BAUDRATE 115200
 641
 642 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 643
 644
 645 #define CONFIG_HOSTNAME         hrcon
 646 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 647 #define CONFIG_BOOTFILE         "uImage"
 648
 649 #define CONFIG_PREBOOT          /* enable preboot variable */
 650
 651 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 652         "netdev=eth0\0"                                                 \
 653         "consoledev=ttyS1\0"                                            \
 654         "u-boot=u-boot.bin\0"                                           \
 655         "kernel_addr=1000000\0"                                 \
 656         "fdt_addr=C00000\0"                                             \
 657         "fdtfile=hrcon.dtb\0"                           \
 658         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 659         "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)      \
 660                 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
 661                 " +${filesize};cp.b ${fileaddr} "                       \
 662                 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"   \
 663         "upd=run load update\0"                                         \
 664
 665 #define CONFIG_NFSBOOTCOMMAND                                           \
 666         "setenv bootargs root=/dev/nfs rw "                             \
 667         "nfsroot=$serverip:$rootpath "                                  \
 668         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 669         "console=$consoledev,$baudrate $othbootargs;"                   \
 670         "tftp ${kernel_addr} $bootfile;"                                \
 671         "tftp ${fdt_addr} $fdtfile;"                                    \
 672         "bootm ${kernel_addr} - ${fdt_addr}"
 673
 674 #define CONFIG_MMCBOOTCOMMAND                                           \
 675         "setenv bootargs root=/dev/mmcblk0p3 rw rootwait "              \
 676         "console=$consoledev,$baudrate $othbootargs;"                   \
 677         "ext2load mmc 0:2 ${kernel_addr} $bootfile;"                    \
 678         "ext2load mmc 0:2 ${fdt_addr} $fdtfile;"                        \
 679         "bootm ${kernel_addr} - ${fdt_addr}"
 680
 681 #define CONFIG_BOOTCOMMAND              CONFIG_MMCBOOTCOMMAND
 682
 683 #endif  /* __CONFIG_H */