include/configs/stm32mp1.h

   1 /* SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause */
   2 /*
   3  * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
   4  *
   5  * Configuration settings for the STM32MP15x CPU
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10 #include <linux/sizes.h>
  11 #include <asm/arch/stm32.h>
  12
  13 #ifndef CONFIG_TFABOOT
  14 /* PSCI support */
  15 #define CONFIG_ARMV7_PSCI_1_0
  16 #define CONFIG_ARMV7_SECURE_BASE                STM32_SYSRAM_BASE
  17 #define CONFIG_ARMV7_SECURE_MAX_SIZE            STM32_SYSRAM_SIZE
  18 #endif
  19
  20 /*
  21  * Configuration of the external SRAM memory used by U-Boot
  22  */
  23 #define CONFIG_SYS_SDRAM_BASE                   STM32_DDR_BASE
  24 #define CONFIG_SYS_INIT_SP_ADDR                 CONFIG_SYS_TEXT_BASE
  25
  26 #ifdef CONFIG_STM32MP1_OPTEE
  27 #define CONFIG_SYS_MEM_TOP_HIDE                 SZ_32M
  28 #endif /* CONFIG_STM32MP1_OPTEE */
  29
  30 /*
  31  * Console I/O buffer size
  32  */
  33 #define CONFIG_SYS_CBSIZE                       SZ_1K
  34
  35 /*
  36  * default load address used for command tftp,  bootm , loadb, ...
  37  */
  38 #define CONFIG_LOADADDR                 0xc2000000
  39 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
  40
  41 /* ATAGs */
  42 #define CONFIG_CMDLINE_TAG
  43 #define CONFIG_SETUP_MEMORY_TAGS
  44 #define CONFIG_INITRD_TAG
  45
  46 /*
  47  * For booting Linux, use the first 256 MB of memory, since this is
  48  * the maximum mapped by the Linux kernel during initialization.
  49  */
  50 #define CONFIG_SYS_BOOTMAPSZ            SZ_256M
  51
  52 /* Extend size of kernel image for uncompression */
  53 #define CONFIG_SYS_BOOTM_LEN            SZ_32M
  54
  55 /* SPL support */
  56 #ifdef CONFIG_SPL
  57 /* SPL use DDR */
  58 #define CONFIG_SPL_BSS_START_ADDR       0xC0200000
  59 #define CONFIG_SPL_BSS_MAX_SIZE         0x00100000
  60 #define CONFIG_SYS_SPL_MALLOC_START     0xC0300000
  61 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x00100000
  62
  63 /* limit SYSRAM usage to first 128 KB */
  64 #define CONFIG_SPL_MAX_SIZE             0x00020000
  65 #define CONFIG_SPL_STACK                (STM32_SYSRAM_BASE + \
  66                                          STM32_SYSRAM_SIZE)
  67 #endif /* #ifdef CONFIG_SPL */
  68
  69 #define CONFIG_SYS_MEMTEST_START        STM32_DDR_BASE
  70 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + SZ_64M)
  71 #define CONFIG_SYS_MEMTEST_SCRATCH      (CONFIG_SYS_MEMTEST_END + 4)
  72
  73 /*MMC SD*/
  74 #define CONFIG_SYS_MMC_MAX_DEVICE       3
  75
  76 /* NAND support */
  77 #define CONFIG_SYS_NAND_ONFI_DETECTION
  78 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  79
  80 /* Ethernet need */
  81 #ifdef CONFIG_DWC_ETH_QOS
  82 #define CONFIG_SYS_NONCACHED_MEMORY     (1 * SZ_1M)     /* 1M */
  83 #define CONFIG_SERVERIP                 192.168.1.1
  84 #define CONFIG_BOOTP_SERVERIP
  85 #define CONFIG_SYS_AUTOLOAD             "no"
  86 #endif
  87
  88 #ifdef CONFIG_DM_VIDEO
  89 #define CONFIG_VIDEO_BMP_RLE8
  90 #define CONFIG_BMP_16BPP
  91 #define CONFIG_BMP_24BPP
  92 #define CONFIG_BMP_32BPP
  93 #endif
  94
  95 /*****************************************************************************/
  96 #ifdef CONFIG_DISTRO_DEFAULTS
  97 /*****************************************************************************/
  98
  99 #if !defined(CONFIG_SPL_BUILD)
 100
 101 #ifdef CONFIG_CMD_MMC
 102 #define BOOT_TARGET_MMC0(func)  func(MMC, mmc, 0)
 103 #define BOOT_TARGET_MMC1(func)  func(MMC, mmc, 1)
 104 #define BOOT_TARGET_MMC2(func)  func(MMC, mmc, 2)
 105 #else
 106 #define BOOT_TARGET_MMC0(func)
 107 #define BOOT_TARGET_MMC1(func)
 108 #define BOOT_TARGET_MMC2(func)
 109 #endif
 110
 111 #ifdef CONFIG_NET
 112 #define BOOT_TARGET_PXE(func)   func(PXE, pxe, na)
 113 #else
 114 #define BOOT_TARGET_PXE(func)
 115 #endif
 116
 117 #ifdef CONFIG_CMD_UBIFS
 118 #define BOOT_TARGET_UBIFS(func) func(UBIFS, ubifs, 0)
 119 #else
 120 #define BOOT_TARGET_UBIFS(func)
 121 #endif
 122
 123 #define BOOT_TARGET_DEVICES(func)       \
 124         BOOT_TARGET_MMC1(func)          \
 125         BOOT_TARGET_UBIFS(func)         \
 126         BOOT_TARGET_MMC0(func)          \
 127         BOOT_TARGET_MMC2(func)          \
 128         BOOT_TARGET_PXE(func)
 129
 130 /*
 131  * bootcmd for stm32mp1:
 132  * for serial/usb: execute the stm32prog command
 133  * for mmc boot (eMMC, SD card), boot only on the same device
 134  * for nand boot, boot with on ubifs partition on nand
 135  * for nor boot, use the default order
 136  */
 137 #define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
 138         "echo \"Boot over ${boot_device}${boot_instance}!\";" \
 139         "if test ${boot_device} = serial || test ${boot_device} = usb;" \
 140         "then stm32prog ${boot_device} ${boot_instance}; " \
 141         "else " \
 142                 "run env_check;" \
 143                 "if test ${boot_device} = mmc;" \
 144                 "then env set boot_targets \"mmc${boot_instance}\"; fi;" \
 145                 "if test ${boot_device} = nand;" \
 146                 "then env set boot_targets ubifs0; fi;" \
 147                 "run distro_bootcmd;" \
 148         "fi;\0"
 149
 150 #include <config_distro_bootcmd.h>
 151
 152 #ifdef CONFIG_STM32MP1_OPTEE
 153 /* with OPTEE: define specific MTD partitions = teeh, teed, teex */
 154 #define STM32MP_MTDPARTS \
 155         "mtdparts_nor0=256k(fsbl1),256k(fsbl2),2m(ssbl),256k(u-boot-env),256k(teeh),256k(teed),256k(teex),-(nor_user)\0" \
 156         "mtdparts_nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),512k(teeh),512k(teed),512k(teex),-(UBI)\0" \
 157         "mtdparts_spi-nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),"\
 158                 "512k(teeh),512k(teed),512k(teex),-(UBI)\0"
 159
 160 #else /* CONFIG_STM32MP1_OPTEE */
 161 #define STM32MP_MTDPARTS \
 162         "mtdparts_nor0=256k(fsbl1),256k(fsbl2),2m(ssbl),256k(u-boot-env),-(nor_user)\0" \
 163         "mtdparts_nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),-(UBI)\0" \
 164         "mtdparts_spi-nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),-(UBI)\0"
 165
 166 #endif /* CONFIG_STM32MP1_OPTEE */
 167
 168 #ifndef CONFIG_SYS_MTDPARTS_RUNTIME
 169 #undef STM32MP_MTDPARTS
 170 #define STM32MP_MTDPARTS
 171 #endif
 172
 173 #define STM32MP_DFU_ALT_RAM \
 174         "dfu_alt_info_ram=ram 0=" \
 175                 "uImage ram ${kernel_addr_r} 0x2000000;" \
 176                 "devicetree.dtb ram ${fdt_addr_r} 0x100000;" \
 177                 "uramdisk.image.gz ram ${ramdisk_addr_r} 0x10000000\0"
 178
 179 #ifdef CONFIG_SET_DFU_ALT_INFO
 180 #define STM32MP_DFU_ALT_INFO \
 181         "dfu_alt_info_nor0=mtd nor0=" \
 182                 "nor_fsbl1 part 1;nor_fsbl2 part 2;" \
 183                 "nor_ssbl part 3;nor_env part 4\0" \
 184         "dfu_alt_info_nand0=mtd nand0="\
 185                 "nand_fsbl part 1;nand_ssbl1 part 2;" \
 186                 "nand_ssbl2 part 3;nand_UBI partubi 4\0" \
 187         "dfu_alt_info_spi-nand0=mtd spi-nand0="\
 188                 "spi-nand_fsbl part 1;spi-nand_ssbl1 part 2;" \
 189                 "spi-nand_ssbl2 part 3;spi-nand_UBI partubi 4\0" \
 190         "dfu_alt_info_mmc0=mmc 0=" \
 191                 "sdcard_fsbl1 part 0 1;sdcard_fsbl2 part 0 2;" \
 192                 "sdcard_ssbl part 0 3;sdcard_bootfs part 0 4;" \
 193                 "sdcard_vendorfs part 0 5;sdcard_rootfs part 0 6;" \
 194                 "sdcard_userfs part 0 7\0" \
 195         "dfu_alt_info_mmc1=mmc 1=" \
 196                 "emmc_fsbl1 raw 0x0 0x200 mmcpart 1;" \
 197                 "emmc_fsbl2 raw 0x0 0x200 mmcpart 2;emmc_ssbl part 1 1;" \
 198                 "emmc_bootfs part 1 2;emmc_vendorfs part 1 3;" \
 199                 "emmc_rootfs part 1 4;emmc_userfs part 1 5\0"
 200 #else
 201 #define STM32MP_DFU_ALT_INFO
 202 #endif
 203
 204 /*
 205  * memory layout for 32M uncompressed/compressed kernel,
 206  * 1M fdt, 1M script, 1M pxe and 1M for splashimage
 207  * and the ramdisk at the end.
 208  */
 209 #define CONFIG_EXTRA_ENV_SETTINGS \
 210         "bootdelay=1\0" \
 211         "kernel_addr_r=0xc2000000\0" \
 212         "fdt_addr_r=0xc4000000\0" \
 213         "scriptaddr=0xc4100000\0" \
 214         "pxefile_addr_r=0xc4200000\0" \
 215         "splashimage=0xc4300000\0"  \
 216         "ramdisk_addr_r=0xc4400000\0" \
 217         "altbootcmd=run bootcmd\0" \
 218         "env_default=1\0" \
 219         "env_check=if test $env_default -eq 1;"\
 220                 " then env set env_default 0;env save;fi\0" \
 221         STM32MP_BOOTCMD \
 222         STM32MP_MTDPARTS \
 223         STM32MP_DFU_ALT_RAM \
 224         STM32MP_DFU_ALT_INFO \
 225         BOOTENV \
 226         "boot_net_usb_start=true\0"
 227
 228 #endif /* ifndef CONFIG_SPL_BUILD */
 229 #endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
 230
 231 #endif /* __CONFIG_H */