include/configs/rut.h

   1 /*
   2  * siemens rut
   3  * (C) Copyright 2013 Siemens Schweiz AG
   4  * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
   5  *
   6  * Based on:
   7  * U-Boot file:/include/configs/am335x_evm.h
   8  *
   9  * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13
  14 #ifndef __CONFIG_RUT_H
  15 #define __CONFIG_RUT_H
  16
  17 #define CONFIG_SIEMENS_MACH_TYPE        MACH_TYPE_RUT
  18
  19 #include "siemens-am33x-common.h"
  20
  21 #define RUT_IOCTRL_VAL  0x18b
  22 #define DDR_PLL_FREQ    303
  23
  24  /* Physical Memory Map */
  25 #define CONFIG_MAX_RAM_BANK_SIZE        (256 << 20) /* 256 MiB */
  26
  27 /* I2C Configuration */
  28 #define CONFIG_SYS_I2C_SPEED            100000
  29
  30 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
  31 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
  32 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
  33 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
  34
  35 #define CONFIG_PHY_NATSEMI
  36
  37 #define CONFIG_FACTORYSET
  38
  39 /* Watchdog */
  40 #define WATCHDOG_TRIGGER_GPIO   14
  41
  42 #ifndef CONFIG_SPL_BUILD
  43
  44 /* Use common default */
  45
  46 /* Default env settings */
  47 #define CONFIG_EXTRA_ENV_SETTINGS \
  48         "hostname=rut\0" \
  49         "ubi_off=2048\0"\
  50         "nand_img_size=0x500000\0" \
  51         "splashpos=m,m\0" \
  52         "optargs=fixrtc --no-log consoleblank=0 \0" \
  53         CONFIG_ENV_SETTINGS_V1 \
  54         CONFIG_ENV_SETTINGS_NAND_V1 \
  55         "mmc_dev=0\0" \
  56         "mmc_root=/dev/mmcblk0p2 rw\0" \
  57         "mmc_root_fs_type=ext4 rootwait\0" \
  58         "mmc_load_uimage=" \
  59                 "mmc rescan; " \
  60                 "setenv bootfile uImage;" \
  61                 "fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
  62         "loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
  63         "importbootenv=echo Importing environment from mmc ...; " \
  64                 "env import -t $loadaddr $filesize\0" \
  65         "mmc_args=run bootargs_defaults;" \
  66                 "mtdparts default;" \
  67                 "setenv bootargs ${bootargs} " \
  68                 "root=${mmc_root} ${mtdparts}" \
  69                 "rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
  70                 "eth=${ethaddr} " \
  71                 "\0" \
  72         "mmc_boot=run mmc_args; " \
  73                 "run mmc_load_uimage; " \
  74                 "bootm ${kloadaddr}\0" \
  75         ""
  76
  77 #ifndef CONFIG_RESTORE_FLASH
  78 /* set to negative value for no autoboot */
  79
  80 #define CONFIG_BOOTCOMMAND \
  81         "if mmc rescan; then " \
  82                 "echo SD/MMC found on device ${mmc_dev};" \
  83                 "if run loadbootenv; then " \
  84                         "echo Loaded environment from ${bootenv};" \
  85                         "run importbootenv;" \
  86                 "fi;" \
  87                 "if test -n $uenvcmd; then " \
  88                         "echo Running uenvcmd ...;" \
  89                         "run uenvcmd;" \
  90                 "fi;" \
  91                 "if run mmc_load_uimage; then " \
  92                         "run mmc_args;" \
  93                         "bootm ${kloadaddr};" \
  94                 "fi;" \
  95         "fi;" \
  96         "run nand_boot;" \
  97         "reset;"
  98
  99 #else
 100
 101 #define CONFIG_BOOTCOMMAND                      \
 102         "setenv autoload no; "                  \
 103         "dhcp; "                                \
 104         "if tftp 80000000 debrick.scr; then "   \
 105                 "source 80000000; "             \
 106         "fi"
 107 #endif
 108
 109 #endif /* CONFIG_SPL_BUILD */
 110
 111 #if defined(CONFIG_VIDEO)
 112 #define CONFIG_VIDEO_DA8XX
 113 #define CONFIG_SPLASH_SCREEN
 114 #define CONFIG_SPLASH_SCREEN_ALIGN
 115 #define CONFIG_VIDEO_LOGO
 116 #define CONFIG_VIDEO_BMP_RLE8
 117 #define CONFIG_VIDEO_BMP_LOGO
 118 #define DA8XX_LCD_CNTL_BASE     LCD_CNTL_BASE
 119
 120 #define CONFIG_SPI
 121
 122 #define BOARD_LCD_RESET         115     /* Bank 3 pin 19 */
 123 #define CONFIG_FORMIKE
 124 #define DISPL_PLL_SPREAD_SPECTRUM
 125 #endif
 126
 127 #endif  /* ! __CONFIG_RUT_H */