include/configs/mx35pdk.h

   1 /*
   2  * (C) Copyright 2010, Stefano Babic <sbabic@denx.de>
   3  *
   4  * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
   5  *
   6  * Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
   7  *
   8  * Configuration for the MX35pdk Freescale board.
   9  *
  10  * SPDX-License-Identifier:     GPL-2.0+
  11  */
  12
  13 #ifndef __CONFIG_H
  14 #define __CONFIG_H
  15
  16 #include <asm/arch/imx-regs.h>
  17
  18  /* High Level Configuration Options */
  19 #define CONFIG_MX35
  20
  21 #define CONFIG_SYS_FSL_CLK
  22
  23 /* Set TEXT at the beginning of the NOR flash */
  24 #define CONFIG_SYS_TEXT_BASE    0xA0000000
  25
  26 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
  27 #define CONFIG_REVISION_TAG
  28 #define CONFIG_SETUP_MEMORY_TAGS
  29 #define CONFIG_INITRD_TAG
  30
  31 /*
  32  * Size of malloc() pool
  33  */
  34 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  35
  36 /*
  37  * Hardware drivers
  38  */
  39 #define CONFIG_SYS_I2C
  40 #define CONFIG_SYS_I2C_MXC
  41 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  42 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  43 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  44 #define CONFIG_MXC_SPI
  45 #define CONFIG_MXC_GPIO
  46
  47 /*
  48  * PMIC Configs
  49  */
  50 #define CONFIG_POWER
  51 #define CONFIG_POWER_I2C
  52 #define CONFIG_POWER_FSL
  53 #define CONFIG_POWER_FSL_MC13892
  54 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR    0x08
  55 #define CONFIG_RTC_MC13XXX
  56
  57 /*
  58  * MFD MC9SDZ60
  59  */
  60 #define CONFIG_FSL_MC9SDZ60
  61 #define CONFIG_SYS_FSL_MC9SDZ60_I2C_ADDR        0x69
  62
  63 /*
  64  * UART (console)
  65  */
  66 #define CONFIG_MXC_UART
  67 #define CONFIG_MXC_UART_BASE    UART1_BASE
  68
  69 /* allow to overwrite serial and ethaddr */
  70 #define CONFIG_ENV_OVERWRITE
  71 #define CONFIG_CONS_INDEX       1
  72
  73 /*
  74  * Command definition
  75  */
  76 #define CONFIG_BOOTP_SUBNETMASK
  77 #define CONFIG_BOOTP_GATEWAY
  78 #define CONFIG_BOOTP_DNS
  79
  80 #define CONFIG_NET_RETRY_COUNT  100
  81
  82
  83 #define CONFIG_LOADADDR         0x80800000      /* loadaddr env var */
  84
  85 /*
  86  * Ethernet on the debug board (SMC911)
  87  */
  88 #define CONFIG_HAS_ETH1
  89 #define CONFIG_ETHPRIME
  90
  91 /*
  92  * Ethernet on SOC (FEC)
  93  */
  94 #define CONFIG_FEC_MXC
  95 #define IMX_FEC_BASE    FEC_BASE_ADDR
  96 #define CONFIG_FEC_MXC_PHYADDR  0x1F
  97
  98 #define CONFIG_MII
  99
 100 #define CONFIG_ARP_TIMEOUT      200UL
 101
 102 /*
 103  * Miscellaneous configurable options
 104  */
 105 #define CONFIG_SYS_LONGHELP     /* undef to save memory */
 106 #define CONFIG_CMDLINE_EDITING
 107
 108 #define CONFIG_AUTO_COMPLETE
 109
 110 #define CONFIG_SYS_MEMTEST_START        0       /* memtest works on */
 111 #define CONFIG_SYS_MEMTEST_END          0x10000
 112
 113 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 114
 115 /*
 116  * Physical Memory Map
 117  */
 118 #define CONFIG_NR_DRAM_BANKS    2
 119 #define PHYS_SDRAM_1            CSD0_BASE_ADDR
 120 #define PHYS_SDRAM_1_SIZE       (128 * 1024 * 1024)
 121 #define PHYS_SDRAM_2            CSD1_BASE_ADDR
 122 #define PHYS_SDRAM_2_SIZE       (128 * 1024 * 1024)
 123
 124 #define CONFIG_SYS_SDRAM_BASE           CSD0_BASE_ADDR
 125 #define CONFIG_SYS_INIT_RAM_ADDR        (IRAM_BASE_ADDR + 0x10000)
 126 #define CONFIG_SYS_INIT_RAM_SIZE                (IRAM_SIZE / 2)
 127 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 128                                         GENERATED_GBL_DATA_SIZE)
 129 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 130                                         CONFIG_SYS_GBL_DATA_OFFSET)
 131
 132 /*
 133  * MTD Command for mtdparts
 134  */
 135 #define CONFIG_MTD_DEVICE
 136 #define CONFIG_FLASH_CFI_MTD
 137 #define CONFIG_MTD_PARTITIONS
 138 #define MTDIDS_DEFAULT          "nand0=mxc_nand,nor0=physmap-flash.0"
 139 #define MTDPARTS_DEFAULT        "mtdparts=mxc_nand:1m(boot),5m(linux)," \
 140                                 "96m(root),8m(cfg),1938m(user);"        \
 141                                 "physmap-flash.0:512k(b),4m(k),30m(u),28m(r)"
 142
 143 /*
 144  * FLASH and environment organization
 145  */
 146 #define CONFIG_SYS_FLASH_BASE           CS0_BASE_ADDR
 147 #define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
 148 #define CONFIG_SYS_MAX_FLASH_SECT 512   /* max number of sectors on one chip */
 149 /* Monitor at beginning of flash */
 150 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 151 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
 152
 153 #define CONFIG_ENV_SECT_SIZE    (128 * 1024)
 154 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 155
 156 /* Address and size of Redundant Environment Sector     */
 157 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 158 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 159
 160 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 161                                 CONFIG_SYS_MONITOR_LEN)
 162
 163 #if defined(CONFIG_FSL_ENV_IN_NAND)
 164         #define CONFIG_ENV_OFFSET       (1024 * 1024)
 165 #endif
 166
 167 /*
 168  * CFI FLASH driver setup
 169  */
 170 #define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
 171 #define CONFIG_FLASH_CFI_DRIVER
 172
 173 /* A non-standard buffered write algorithm */
 174 #define CONFIG_FLASH_SPANSION_S29WS_N
 175 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       /* faster */
 176 #define CONFIG_SYS_FLASH_PROTECTION     /* Use hardware sector protection */
 177
 178 /*
 179  * NAND FLASH driver setup
 180  */
 181 #define CONFIG_MXC_NAND_REGS_BASE       (NFC_BASE_ADDR)
 182 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 183 #define CONFIG_SYS_NAND_BASE            (NFC_BASE_ADDR)
 184 #define CONFIG_MXC_NAND_HWECC
 185 #define CONFIG_SYS_NAND_LARGEPAGE
 186
 187 /* EHCI driver */
 188 #define CONFIG_EHCI_IS_TDI
 189 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 190 #define CONFIG_USB_EHCI_MXC
 191 #define CONFIG_MXC_USB_PORT     0
 192 #define CONFIG_MXC_USB_FLAGS    (MXC_EHCI_INTERFACE_DIFF_UNI | \
 193                                  MXC_EHCI_POWER_PINS_ENABLED | \
 194                                  MXC_EHCI_OC_PIN_ACTIVE_LOW)
 195 #define CONFIG_MXC_USB_PORTSC   (MXC_EHCI_UTMI_16BIT | MXC_EHCI_MODE_UTMI)
 196
 197 /* mmc driver */
 198 #define CONFIG_FSL_ESDHC
 199 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
 200 #define CONFIG_SYS_FSL_ESDHC_NUM        1
 201
 202 /*
 203  * Default environment and default scripts
 204  * to update uboot and load kernel
 205  */
 206
 207 #define CONFIG_HOSTNAME "mx35pdk"
 208 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 209         "netdev=eth1\0"                                                 \
 210         "ethprime=smc911x\0"                                            \
 211         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 212                 "nfsroot=${serverip}:${rootpath}\0"                     \
 213         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 214         "addip_sta=setenv bootargs ${bootargs} "                        \
 215                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 216                 ":${hostname}:${netdev}:off panic=1\0"                  \
 217         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 218         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
 219                 "else run addip_sta;fi\0"                               \
 220         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 221         "addtty=setenv bootargs ${bootargs}"                            \
 222                 " console=ttymxc0,${baudrate}\0"                        \
 223         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
 224         "loadaddr=80800000\0"                                           \
 225         "kernel_addr_r=80800000\0"                                      \
 226         "hostname=" __stringify(CONFIG_HOSTNAME) "\0"                   \
 227         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"            \
 228         "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0"      \
 229         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 230                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 231         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 232                 "bootm ${kernel_addr}\0"                                \
 233         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 234                 "run nfsargs addip addtty addmtd addmisc;"              \
 235                 "bootm ${kernel_addr_r}\0"                              \
 236         "net_self_load=tftp ${kernel_addr_r} ${bootfile};"              \
 237                 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0"             \
 238         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"          \
 239         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 240         "uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"         \
 241         "update=protect off ${uboot_addr} +80000;"                      \
 242                 "erase ${uboot_addr} +80000;"                           \
 243                 "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"          \
 244         "upd=if run load;then echo Updating u-boot;if run update;"      \
 245                 "then echo U-Boot updated;"                             \
 246                         "else echo Error updating u-boot !;"            \
 247                         "echo Board without bootloader !!;"             \
 248                 "fi;"                                                   \
 249                 "else echo U-Boot not downloaded..exiting;fi\0"         \
 250         "bootcmd=run net_nfs\0"
 251
 252 #endif                          /* __CONFIG_H */