include/configs/lx2160a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2018-2021 NXP
   4  */
   5
   6 #ifndef __LX2_COMMON_H
   7 #define __LX2_COMMON_H
   8
   9 #include <asm/arch/stream_id_lsch3.h>
  10 #include <asm/arch/config.h>
  11 #include <asm/arch/soc.h>
  12
  13 #define CONFIG_FSL_MEMAC
  14
  15 #define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SYS_TEXT_BASE
  16 #define CONFIG_SYS_FLASH_BASE           0x20000000
  17
  18 /* DDR */
  19 #define CONFIG_SYS_FSL_DDR_INTLV_256B   /* force 256 byte interleaving */
  20 #define CONFIG_VERY_BIG_RAM
  21 #define CONFIG_SYS_DDR_SDRAM_BASE               0x80000000UL
  22 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  23 #define CONFIG_SYS_DDR_BLOCK2_BASE              0x2080000000ULL
  24 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS       2
  25 #define CONFIG_SYS_SDRAM_SIZE                   0x200000000UL
  26 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  27 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  28 #define SPD_EEPROM_ADDRESS1             0x51
  29 #define SPD_EEPROM_ADDRESS2             0x52
  30 #define SPD_EEPROM_ADDRESS3             0x53
  31 #define SPD_EEPROM_ADDRESS4             0x54
  32 #define SPD_EEPROM_ADDRESS5             0x55
  33 #define SPD_EEPROM_ADDRESS6             0x56
  34 #define SPD_EEPROM_ADDRESS              SPD_EEPROM_ADDRESS1
  35 #define CONFIG_SYS_SPD_BUS_NUM          0       /* SPD on I2C bus 0 */
  36 #define CONFIG_SYS_MONITOR_LEN          (936 * 1024)
  37
  38 /* Miscellaneous configurable options */
  39
  40 /* SMP Definitinos  */
  41 #define CPU_RELEASE_ADDR                secondary_boot_addr
  42
  43 /* Generic Timer Definitions */
  44 /*
  45  * This is not an accurate number. It is used in start.S. The frequency
  46  * will be udpated later when get_bus_freq(0) is available.
  47  */
  48
  49
  50 /* Serial Port */
  51 #define CONFIG_PL011_CLOCK              (get_bus_freq(0) / 4)
  52 #define CONFIG_SYS_SERIAL0              0x21c0000
  53 #define CONFIG_SYS_SERIAL1              0x21d0000
  54 #define CONFIG_SYS_SERIAL2              0x21e0000
  55 #define CONFIG_SYS_SERIAL3              0x21f0000
  56 /*below might needs to be removed*/
  57 #define CONFIG_PL01x_PORTS              {(void *)CONFIG_SYS_SERIAL0, \
  58                                         (void *)CONFIG_SYS_SERIAL1, \
  59                                         (void *)CONFIG_SYS_SERIAL2, \
  60                                         (void *)CONFIG_SYS_SERIAL3 }
  61
  62 /* MC firmware */
  63 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH         0x20000
  64 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET        0x00F00000
  65 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH         0x20000
  66 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET        0x00F20000
  67 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS        5000
  68
  69 /*
  70  * Carve out a DDR region which will not be used by u-boot/Linux
  71  *
  72  * It will be used by MC and Debug Server. The MC region must be
  73  * 512MB aligned, so the min size to hide is 512MB.
  74  */
  75 #ifdef CONFIG_FSL_MC_ENET
  76 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE    (256UL * 1024 * 1024)
  77 #endif
  78
  79 /* I2C bus multiplexer */
  80 #define I2C_MUX_PCA_ADDR_PRI            0x77 /* Primary Mux*/
  81 #define I2C_MUX_CH_DEFAULT              0x8
  82
  83 /* RTC */
  84 #define RTC
  85 #define CONFIG_SYS_I2C_RTC_ADDR         0x51  /* Channel 3*/
  86
  87 /* EEPROM */
  88 #define CONFIG_SYS_I2C_EEPROM_NXID
  89 #define CONFIG_SYS_EEPROM_BUS_NUM               0
  90
  91 /* Qixis */
  92 #define CONFIG_SYS_I2C_FPGA_ADDR                0x66
  93
  94 /* PCI */
  95 #ifdef CONFIG_PCI
  96 #define CONFIG_PCI_SCAN_SHOW
  97 #endif
  98
  99 /* SATA */
 100
 101 #ifdef CONFIG_SCSI
 102 #define CONFIG_SYS_SATA1                AHCI_BASE_ADDR1
 103 #define CONFIG_SYS_SATA2                AHCI_BASE_ADDR2
 104 #endif
 105
 106 /* USB */
 107 #ifdef CONFIG_USB_HOST
 108 #ifndef CONFIG_TARGET_LX2162AQDS
 109 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 110 #endif
 111 #endif
 112
 113 #define COUNTER_FREQUENCY_REAL          (get_board_sys_clk() / 4)
 114
 115 #define CONFIG_HWCONFIG
 116 #define HWCONFIG_BUFFER_SIZE            128
 117
 118 /* Monitor Command Prompt */
 119 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 120 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE /* Boot args buffer */
 121
 122 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 123
 124 /* Initial environment variables */
 125 #define XSPI_MC_INIT_CMD                                \
 126         "sf probe 0:0 && "                              \
 127         "sf read 0x80640000 0x640000 0x80000 && "       \
 128         "sf read $fdt_addr_r 0xf00000 0x100000 && "     \
 129         "env exists secureboot && "                     \
 130         "esbc_validate 0x80640000 && "                  \
 131         "esbc_validate 0x80680000; "                    \
 132         "sf read 0x80a00000 0xa00000 0x300000 && "      \
 133         "sf read 0x80e00000 0xe00000 0x100000; "        \
 134         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 135
 136 #define SD_MC_INIT_CMD                          \
 137         "mmc read 0x80a00000 0x5000 0x1200;"    \
 138         "mmc read 0x80e00000 0x7000 0x800;"     \
 139         "mmc read $fdt_addr_r 0x7800 0x800;"    \
 140         "env exists secureboot && "             \
 141         "mmc read 0x80640000 0x3200 0x20 && "   \
 142         "mmc read 0x80680000 0x3400 0x20 && "   \
 143         "esbc_validate 0x80640000 && "          \
 144         "esbc_validate 0x80680000 ;"            \
 145         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 146
 147 #define SD2_MC_INIT_CMD                         \
 148         "mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \
 149         "mmc read 0x80e00000 0x7000 0x800;"     \
 150         "mmc read $fdt_addr_r 0x7800 0x800;"    \
 151         "env exists secureboot && "             \
 152         "mmc read 0x80640000 0x3200 0x20 && "   \
 153         "mmc read 0x80680000 0x3400 0x20 && "   \
 154         "esbc_validate 0x80640000 && "          \
 155         "esbc_validate 0x80680000 ;"            \
 156         "fsl_mc start mc 0x80a00000 0x80e00000\0"
 157
 158 #define EXTRA_ENV_SETTINGS                      \
 159         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 160         "ramdisk_addr=0x800000\0"               \
 161         "ramdisk_size=0x2000000\0"              \
 162         "fdt_high=0xa0000000\0"                 \
 163         "initrd_high=0xffffffffffffffff\0"      \
 164         "kernel_start=0x1000000\0"              \
 165         "kernelheader_start=0x600000\0"         \
 166         "scriptaddr=0x80000000\0"               \
 167         "scripthdraddr=0x80080000\0"            \
 168         "fdtheader_addr_r=0x80100000\0"         \
 169         "kernelheader_addr_r=0x80200000\0"      \
 170         "kernel_addr_r=0x81000000\0"            \
 171         "kernelheader_size=0x40000\0"           \
 172         "fdt_addr_r=0x90000000\0"               \
 173         "load_addr=0xa0000000\0"                \
 174         "kernel_size=0x2800000\0"               \
 175         "kernel_addr_sd=0x8000\0"               \
 176         "kernelhdr_addr_sd=0x3000\0"            \
 177         "kernel_size_sd=0x14000\0"              \
 178         "kernelhdr_size_sd=0x20\0"              \
 179         "console=ttyAMA0,38400n8\0"             \
 180         BOOTENV                                 \
 181         "mcmemsize=0x70000000\0"                \
 182         XSPI_MC_INIT_CMD                                \
 183         "scan_dev_for_boot_part="               \
 184                 "part list ${devtype} ${devnum} devplist; "     \
 185                 "env exists devplist || setenv devplist 1; "    \
 186                 "for distro_bootpart in ${devplist}; do "       \
 187                         "if fstype ${devtype} "                 \
 188                                 "${devnum}:${distro_bootpart} " \
 189                                 "bootfstype; then "             \
 190                                 "run scan_dev_for_boot; "       \
 191                         "fi; "                                  \
 192                 "done\0"                                        \
 193         "boot_a_script="                                        \
 194                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 195                         "${scriptaddr} ${prefix}${script}; "    \
 196                 "env exists secureboot && load ${devtype} "     \
 197                         "${devnum}:${distro_bootpart} "         \
 198                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 199                         "&& esbc_validate ${scripthdraddr};"    \
 200                 "source ${scriptaddr}\0"
 201
 202 #define XSPI_NOR_BOOTCOMMAND                                            \
 203                         "sf probe 0:0; "                                \
 204                         "sf read 0x806c0000 0x6c0000 0x40000; "         \
 205                         "env exists mcinitcmd && env exists secureboot" \
 206                         " && esbc_validate 0x806c0000; "                \
 207                         "sf read 0x80d00000 0xd00000 0x100000; "        \
 208                         "env exists mcinitcmd && "                      \
 209                         "fsl_mc lazyapply dpl 0x80d00000; "             \
 210                         "run distro_bootcmd;run xspi_bootcmd; "         \
 211                         "env exists secureboot && esbc_halt;"
 212
 213 #define SD_BOOTCOMMAND                                          \
 214                 "env exists mcinitcmd && mmcinfo; "             \
 215                 "mmc read 0x80d00000 0x6800 0x800; "            \
 216                 "env exists mcinitcmd && env exists secureboot "        \
 217                 " && mmc read 0x806C0000 0x3600 0x20 "          \
 218                 "&& esbc_validate 0x806C0000;env exists mcinitcmd "     \
 219                 "&& fsl_mc lazyapply dpl 0x80d00000;"           \
 220                 "run distro_bootcmd;run sd_bootcmd;"            \
 221                 "env exists secureboot && esbc_halt;"
 222
 223 #define SD2_BOOTCOMMAND                                         \
 224                 "mmc dev 1; env exists mcinitcmd && mmcinfo; "  \
 225                 "mmc read 0x80d00000 0x6800 0x800; "            \
 226                 "env exists mcinitcmd && env exists secureboot "        \
 227                 " && mmc read 0x806C0000 0x3600 0x20 "          \
 228                 "&& esbc_validate 0x806C0000;env exists mcinitcmd "     \
 229                 "&& fsl_mc lazyapply dpl 0x80d00000;"           \
 230                 "run distro_bootcmd;run sd2_bootcmd;"           \
 231                 "env exists secureboot && esbc_halt;"
 232
 233 #ifdef CONFIG_CMD_USB
 234 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
 235 #else
 236 #define BOOT_TARGET_DEVICES_USB(func)
 237 #endif
 238
 239 #ifdef CONFIG_MMC
 240 #define BOOT_TARGET_DEVICES_MMC(func, instance) func(MMC, mmc, instance)
 241 #else
 242 #define BOOT_TARGET_DEVICES_MMC(func)
 243 #endif
 244
 245 #ifdef CONFIG_SCSI
 246 #define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
 247 #else
 248 #define BOOT_TARGET_DEVICES_SCSI(func)
 249 #endif
 250
 251 #ifdef CONFIG_CMD_DHCP
 252 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
 253 #else
 254 #define BOOT_TARGET_DEVICES_DHCP(func)
 255 #endif
 256
 257 #define BOOT_TARGET_DEVICES(func) \
 258         BOOT_TARGET_DEVICES_USB(func) \
 259         BOOT_TARGET_DEVICES_MMC(func, 0) \
 260         BOOT_TARGET_DEVICES_MMC(func, 1) \
 261         BOOT_TARGET_DEVICES_SCSI(func) \
 262         BOOT_TARGET_DEVICES_DHCP(func)
 263 #include <config_distro_bootcmd.h>
 264
 265 #endif /* __LX2_COMMON_H */