include/configs/ls2085a_common.h

   1 /*
   2  * Copyright (C) 2014 Freescale Semiconductor
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS2_COMMON_H
   8 #define __LS2_COMMON_H
   9
  10 #define CONFIG_SYS_GENERIC_BOARD
  11
  12 #define CONFIG_REMAKE_ELF
  13 #define CONFIG_FSL_LSCH3
  14 #define CONFIG_LS2085A
  15 #define CONFIG_GICV3
  16 #define CONFIG_FSL_TZPC_BP147
  17
  18 /* Errata fixes */
  19 #define CONFIG_ARM_ERRATA_828024
  20 #define CONFIG_ARM_ERRATA_826974
  21
  22 /* We need architecture specific misc initializations */
  23 #define CONFIG_ARCH_MISC_INIT
  24
  25 /* Link Definitions */
  26 #define CONFIG_SYS_TEXT_BASE            0x30001000
  27
  28 #ifdef CONFIG_EMU
  29 #define CONFIG_SYS_NO_FLASH
  30 #endif
  31
  32 #define CONFIG_SUPPORT_RAW_INITRD
  33
  34 #define CONFIG_SKIP_LOWLEVEL_INIT
  35 #define CONFIG_BOARD_EARLY_INIT_F       1
  36
  37 /* Flat Device Tree Definitions */
  38 #define CONFIG_OF_LIBFDT
  39 #define CONFIG_OF_BOARD_SETUP
  40
  41 /* new uImage format support */
  42 #define CONFIG_FIT
  43 #define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */
  44
  45 #define CONFIG_FSL_DDR_INTERACTIVE      /* Interactive debugging */
  46 #ifndef CONFIG_SYS_FSL_DDR4
  47 #define CONFIG_SYS_FSL_DDR3             /* Use DDR3 memory */
  48 #define CONFIG_SYS_DDR_RAW_TIMING
  49 #endif
  50 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  51 #define CONFIG_CHIP_SELECTS_PER_CTRL    4
  52
  53 #define CONFIG_SYS_FSL_DDR_INTLV_256B   /* force 256 byte interleaving */
  54
  55 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000UL
  56 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  57 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  58 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x8080000000ULL
  59 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS       2
  60
  61 /*
  62  * SMP Definitinos
  63  */
  64 #define CPU_RELEASE_ADDR                secondary_boot_func
  65
  66 #define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
  67 #define CONFIG_SYS_DP_DDR_BASE          0x6000000000ULL
  68 /*
  69  * DDR controller use 0 as the base address for binding.
  70  * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
  71  */
  72 #define CONFIG_SYS_DP_DDR_BASE_PHY      0
  73 #define CONFIG_DP_DDR_CTRL              2
  74 #define CONFIG_DP_DDR_NUM_CTRLS         1
  75 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR       1
  76
  77 /* Generic Timer Definitions */
  78 #define COUNTER_FREQUENCY               12000000        /* 12MHz */
  79
  80 /* Size of malloc() pool */
  81 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2048 * 1024)
  82
  83 /* I2C */
  84 #define CONFIG_CMD_I2C
  85 #define CONFIG_SYS_I2C
  86 #define CONFIG_SYS_I2C_MXC
  87 #define CONFIG_SYS_MXC_I2C1_SPEED       40000000
  88 #define CONFIG_SYS_MXC_I2C2_SPEED       40000000
  89
  90 /* Serial Port */
  91 #define CONFIG_CONS_INDEX       2
  92 #define CONFIG_SYS_NS16550
  93 #define CONFIG_SYS_NS16550_SERIAL
  94 #define CONFIG_SYS_NS16550_REG_SIZE     1
  95 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
  96
  97 #define CONFIG_BAUDRATE                 115200
  98 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  99
 100 /* IFC */
 101 #define CONFIG_FSL_IFC
 102 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
 103 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 104 /*
 105  * During booting, CS0 needs to be at the region of 0x30000000, i.e. the IFC
 106  * address 0. But this region is limited to 256MB. To accommodate bigger NOR
 107  * flash and other devices, we will map CS0 to 0x580000000 after relocation.
 108  * CONFIG_SYS_FLASH_BASE has the final address (core view)
 109  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
 110  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
 111  * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
 112  */
 113 #define CONFIG_SYS_FLASH_BASE                   0x580000000ULL
 114 #define CONFIG_SYS_FLASH_BASE_PHYS              0x80000000
 115 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY        0x00000000
 116
 117 /*
 118  * NOR Flash Timing Params
 119  */
 120 #define CONFIG_SYS_NOR0_CSPR                                    \
 121         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
 122         CSPR_PORT_SIZE_16                                       | \
 123         CSPR_MSEL_NOR                                           | \
 124         CSPR_V)
 125 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
 126         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
 127         CSPR_PORT_SIZE_16                                       | \
 128         CSPR_MSEL_NOR                                           | \
 129         CSPR_V)
 130 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(12)
 131 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x1) | \
 132                                 FTIM0_NOR_TEADC(0x1) | \
 133                                 FTIM0_NOR_TEAHC(0x1))
 134 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x1) | \
 135                                 FTIM1_NOR_TRAD_NOR(0x1))
 136 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x0) | \
 137                                 FTIM2_NOR_TCH(0x0) | \
 138                                 FTIM2_NOR_TWP(0x1))
 139 #define CONFIG_SYS_NOR_FTIM3    0x04000000
 140 #define CONFIG_SYS_IFC_CCR      0x01000000
 141
 142 #ifndef CONFIG_SYS_NO_FLASH
 143 #define CONFIG_FLASH_CFI_DRIVER
 144 #define CONFIG_SYS_FLASH_CFI
 145 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 146 #define CONFIG_SYS_FLASH_QUIET_TEST
 147 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 148
 149 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 150 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 151 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 152 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 153
 154 #define CONFIG_SYS_FLASH_EMPTY_INFO
 155 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
 156 #endif
 157
 158 #define CONFIG_NAND_FSL_IFC
 159 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 160 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 161 #define CONFIG_SYS_NAND_BASE            0x520000000
 162 #define CONFIG_SYS_NAND_BASE_PHYS       0x20000000
 163
 164 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 165 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 166                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 167                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 168                                 | CSPR_V)
 169 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 170
 171 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 172                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 173                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 174                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */ \
 175                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
 176                                 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
 177                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 178
 179 #define CONFIG_SYS_NAND_ONFI_DETECTION
 180
 181 /* ONFI NAND Flash mode0 Timing Params */
 182 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 183                                         FTIM0_NAND_TWP(0x18)   | \
 184                                         FTIM0_NAND_TWCHT(0x07) | \
 185                                         FTIM0_NAND_TWH(0x0a))
 186 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 187                                         FTIM1_NAND_TWBE(0x39)  | \
 188                                         FTIM1_NAND_TRR(0x0e)   | \
 189                                         FTIM1_NAND_TRP(0x18))
 190 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f) | \
 191                                         FTIM2_NAND_TREH(0x0a) | \
 192                                         FTIM2_NAND_TWHRE(0x1e))
 193 #define CONFIG_SYS_NAND_FTIM3           0x0
 194
 195 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 196 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 197 #define CONFIG_CMD_NAND
 198
 199 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 200
 201 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 202 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 203 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 204 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 205 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 206 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 207 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 208 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 209 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 210
 211 /* Debug Server firmware */
 212 #define CONFIG_FSL_DEBUG_SERVER
 213 #define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE     (512UL * 1024 * 1024)
 214 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
 215 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR                 0x580C00000ULL
 216 /* 2 sec timeout */
 217 #define CONFIG_SYS_DEBUG_SERVER_TIMEOUT                 (2 * 1000 * 1000)
 218
 219 /* MC firmware */
 220 #define CONFIG_FSL_MC_ENET
 221 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE    (512UL * 1024 * 1024)
 222 #define CONFIG_SYS_LS_MC_FW_IN_NOR
 223 #define CONFIG_SYS_LS_MC_FW_ADDR        0x580200000ULL
 224 #define CONFIG_SYS_LS_MC_DPL_IN_NOR
 225 #define CONFIG_SYS_LS_MC_DPL_ADDR       0x5806C0000ULL
 226 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */
 227 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH (256 * 1024)
 228 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0xe00000
 229
 230 /* Carve out a DDR region which will not be used by u-boot/Linux */
 231 #if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
 232 #define CONFIG_SYS_MEM_TOP_HIDE         get_dram_size_to_hide()
 233 #endif
 234
 235 /* Command line configuration */
 236 #define CONFIG_CMD_CACHE
 237 #define CONFIG_CMD_BDI
 238 #define CONFIG_CMD_DHCP
 239 #define CONFIG_CMD_ENV
 240 #define CONFIG_CMD_FLASH
 241 #define CONFIG_CMD_IMI
 242 #define CONFIG_CMD_MEMORY
 243 #define CONFIG_CMD_MII
 244 #define CONFIG_CMD_NET
 245 #define CONFIG_CMD_PING
 246 #define CONFIG_CMD_SAVEENV
 247 #define CONFIG_CMD_RUN
 248 #define CONFIG_CMD_BOOTD
 249 #define CONFIG_CMD_ECHO
 250 #define CONFIG_CMD_SOURCE
 251 #define CONFIG_CMD_FAT
 252 #define CONFIG_DOS_PARTITION
 253
 254 /* Miscellaneous configurable options */
 255 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 256 #define CONFIG_ARCH_EARLY_INIT_R
 257
 258 /* Physical Memory Map */
 259 /* fixme: these need to be checked against the board */
 260 #define CONFIG_CHIP_SELECTS_PER_CTRL    4
 261 #define CONFIG_SYS_CLK_FREQ     100000000
 262 #define CONFIG_DDR_CLK_FREQ     133333333
 263
 264 #define CONFIG_NR_DRAM_BANKS            3
 265
 266 #define CONFIG_HWCONFIG
 267 #define HWCONFIG_BUFFER_SIZE            128
 268
 269 #define CONFIG_DISPLAY_CPUINFO
 270
 271 /* Initial environment variables */
 272 #define CONFIG_EXTRA_ENV_SETTINGS               \
 273         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 274         "loadaddr=0x80100000\0"                 \
 275         "kernel_addr=0x100000\0"                \
 276         "ramdisk_addr=0x800000\0"               \
 277         "ramdisk_size=0x2000000\0"              \
 278         "fdt_high=0xffffffffffffffff\0"         \
 279         "initrd_high=0xffffffffffffffff\0"      \
 280         "kernel_start=0x581200000\0"            \
 281         "kernel_load=0xa0000000\0"              \
 282         "kernel_size=0x1000000\0"               \
 283         "console=ttyAMA0,38400n8\0"
 284
 285 #define CONFIG_BOOTARGS         "console=ttyS1,115200 root=/dev/ram0 " \
 286                                 "earlycon=uart8250,mmio,0x21c0600,115200 " \
 287                                 "default_hugepagesz=2m hugepagesz=2m " \
 288                                 "hugepages=16"
 289 #define CONFIG_BOOTCOMMAND              "cp.b $kernel_start $kernel_load "     \
 290                                         "$kernel_size && bootm $kernel_load"
 291 #define CONFIG_BOOTDELAY                1
 292
 293 /* Store environment at top of flash */
 294 #define CONFIG_ENV_IS_NOWHERE           1
 295 #define CONFIG_ENV_SIZE                 0x1000
 296
 297 /* Monitor Command Prompt */
 298 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 299 #define CONFIG_SYS_PROMPT               "> "
 300 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 301                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 302 #define CONFIG_SYS_HUSH_PARSER
 303 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 304 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE /* Boot args buffer */
 305 #define CONFIG_SYS_LONGHELP
 306 #define CONFIG_CMDLINE_EDITING          1
 307 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 308
 309 #ifndef __ASSEMBLY__
 310 unsigned long get_dram_size_to_hide(void);
 311 #endif
 312
 313 #endif /* __LS2_COMMON_H */