include/configs/ls1046a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2016 Freescale Semiconductor
   4  * Copyright 2019-2021 NXP
   5  */
   6
   7 #ifndef __LS1046A_COMMON_H
   8 #define __LS1046A_COMMON_H
   9
  10 /* SPL build */
  11 #ifdef CONFIG_SPL_BUILD
  12 #define SPL_NO_QBMAN
  13 #define SPL_NO_FMAN
  14 #define SPL_NO_ENV
  15 #define SPL_NO_MISC
  16 #define SPL_NO_QSPI
  17 #define SPL_NO_USB
  18 #define SPL_NO_SATA
  19 #endif
  20 #if defined(CONFIG_SPL_BUILD) && \
  21         (defined(CONFIG_NAND_BOOT) || defined(CONFIG_QSPI_BOOT))
  22 #define SPL_NO_MMC
  23 #endif
  24 #if defined(CONFIG_SPL_BUILD)           && \
  25         !defined(CONFIG_SPL_FSL_LS_PPA)
  26 #define SPL_NO_IFC
  27 #endif
  28
  29 #include <asm/arch/config.h>
  30 #include <asm/arch/stream_id_lsch2.h>
  31
  32 /* Link Definitions */
  33
  34 #define CONFIG_VERY_BIG_RAM
  35 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  36 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  37 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  38 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
  39
  40 #define CPU_RELEASE_ADDR               secondary_boot_addr
  41
  42 /* Serial Port */
  43 #define CONFIG_SYS_NS16550_SERIAL
  44 #define CONFIG_SYS_NS16550_REG_SIZE     1
  45 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  46
  47 /* SD boot SPL */
  48 #ifdef CONFIG_SD_BOOT
  49 #ifdef CONFIG_NXP_ESBC
  50 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
  51 /*
  52  * HDR would be appended at end of image and copied to DDR along
  53  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  54  * size increases then increase this size in case of secure boot as
  55  * it uses raw u-boot image instead of fit image.
  56  */
  57 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
  58 #else
  59 #define CONFIG_SYS_MONITOR_LEN          0x100000
  60 #endif /* ifdef CONFIG_NXP_ESBC */
  61 #endif
  62
  63 #if defined(CONFIG_QSPI_BOOT) && defined(CONFIG_SPL)
  64 #define CONFIG_SYS_MONITOR_LEN          0x100000
  65 #endif
  66
  67 /* NAND SPL */
  68 #ifdef CONFIG_NAND_BOOT
  69 #define CONFIG_SYS_NAND_U_BOOT_DST      CONFIG_SYS_TEXT_BASE
  70 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
  71
  72 #define CONFIG_SYS_MONITOR_LEN          0xa0000
  73 #endif
  74
  75 /* GPIO */
  76
  77 /* I2C */
  78
  79 /* PCIe */
  80 #define CONFIG_PCIE1            /* PCIE controller 1 */
  81 #define CONFIG_PCIE2            /* PCIE controller 2 */
  82 #define CONFIG_PCIE3            /* PCIE controller 3 */
  83
  84 #ifdef CONFIG_PCI
  85 #define CONFIG_PCI_SCAN_SHOW
  86 #endif
  87
  88 /* SATA */
  89 #ifndef SPL_NO_SATA
  90 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
  91 #endif
  92
  93 /* FMan ucode */
  94 #ifndef SPL_NO_FMAN
  95 #define CONFIG_SYS_DPAA_FMAN
  96 #ifdef CONFIG_SYS_DPAA_FMAN
  97 #define CONFIG_SYS_FM_MURAM_SIZE        0x60000
  98 #endif
  99 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 100 #endif
 101
 102 /* Miscellaneous configurable options */
 103
 104 #define CONFIG_HWCONFIG
 105 #define HWCONFIG_BUFFER_SIZE            128
 106
 107 #define BOOT_TARGET_DEVICES(func) \
 108         func(SCSI, scsi, 0) \
 109         func(MMC, mmc, 0) \
 110         func(USB, usb, 0) \
 111         func(DHCP, dhcp, na)
 112 #include <config_distro_bootcmd.h>
 113
 114 #if defined(CONFIG_TARGET_LS1046AFRWY)
 115 #define LS1046A_BOOT_SRC_AND_HDR\
 116         "boot_scripts=ls1046afrwy_boot.scr\0"   \
 117         "boot_script_hdr=hdr_ls1046afrwy_bs.out\0"
 118 #elif defined(CONFIG_TARGET_LS1046AQDS)
 119 #define LS1046A_BOOT_SRC_AND_HDR\
 120         "boot_scripts=ls1046aqds_boot.scr\0"    \
 121         "boot_script_hdr=hdr_ls1046aqds_bs.out\0"
 122 #else
 123 #define LS1046A_BOOT_SRC_AND_HDR\
 124         "boot_scripts=ls1046ardb_boot.scr\0"    \
 125         "boot_script_hdr=hdr_ls1046ardb_bs.out\0"
 126 #endif
 127 #ifndef SPL_NO_MISC
 128 /* Initial environment variables */
 129 #define CONFIG_EXTRA_ENV_SETTINGS               \
 130         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 131         "ramdisk_addr=0x800000\0"               \
 132         "ramdisk_size=0x2000000\0"              \
 133         "bootm_size=0x10000000\0"               \
 134         "kernel_addr=0x61000000\0"              \
 135         "scriptaddr=0x80000000\0"               \
 136         "scripthdraddr=0x80080000\0"            \
 137         "fdtheader_addr_r=0x80100000\0"         \
 138         "kernelheader_addr_r=0x80200000\0"      \
 139         "load_addr=0xa0000000\0"            \
 140         "kernel_addr_r=0x81000000\0"            \
 141         "fdt_addr_r=0x90000000\0"               \
 142         "ramdisk_addr_r=0xa0000000\0"           \
 143         "kernel_start=0x1000000\0"              \
 144         "kernelheader_start=0x600000\0"         \
 145         "kernel_load=0xa0000000\0"              \
 146         "kernel_size=0x2800000\0"               \
 147         "kernelheader_size=0x40000\0"           \
 148         "kernel_addr_sd=0x8000\0"               \
 149         "kernel_size_sd=0x14000\0"              \
 150         "kernelhdr_addr_sd=0x3000\0"            \
 151         "kernelhdr_size_sd=0x10\0"              \
 152         "console=ttyS0,115200\0"                \
 153          CONFIG_MTDPARTS_DEFAULT "\0"           \
 154         BOOTENV                                 \
 155         LS1046A_BOOT_SRC_AND_HDR                \
 156         "scan_dev_for_boot_part="               \
 157                 "part list ${devtype} ${devnum} devplist; "   \
 158                 "env exists devplist || setenv devplist 1; "  \
 159                 "for distro_bootpart in ${devplist}; do "     \
 160                   "if fstype ${devtype} "                  \
 161                         "${devnum}:${distro_bootpart} "      \
 162                         "bootfstype; then "                  \
 163                         "run scan_dev_for_boot; "            \
 164                   "fi; "                                   \
 165                 "done\0"                                   \
 166         "boot_a_script="                                  \
 167                 "load ${devtype} ${devnum}:${distro_bootpart} "  \
 168                         "${scriptaddr} ${prefix}${script}; "    \
 169                 "env exists secureboot && load ${devtype} "     \
 170                         "${devnum}:${distro_bootpart} "         \
 171                         "${scripthdraddr} ${prefix}${boot_script_hdr}; " \
 172                         "env exists secureboot "        \
 173                         "&& esbc_validate ${scripthdraddr};"    \
 174                 "source ${scriptaddr}\0"          \
 175         "qspi_bootcmd=echo Trying load from qspi..;"      \
 176                 "sf probe && sf read $load_addr "         \
 177                 "$kernel_start $kernel_size; env exists secureboot "    \
 178                 "&& sf read $kernelheader_addr_r $kernelheader_start "  \
 179                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 180                 "bootm $load_addr#$board\0"             \
 181         "nand_bootcmd=echo Trying load from nand..;"      \
 182                 "nand info; nand read $load_addr "         \
 183                 "$kernel_start $kernel_size; env exists secureboot "    \
 184                 "&& nand read $kernelheader_addr_r $kernelheader_start " \
 185                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 186                 "bootm $load_addr#$board\0"             \
 187         "nor_bootcmd=echo Trying load from nor..;"      \
 188                 "cp.b $kernel_addr $load_addr "         \
 189                 "$kernel_size; env exists secureboot "  \
 190                 "&& cp.b $kernelheader_addr $kernelheader_addr_r "      \
 191                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 192                 "bootm $load_addr#$board\0"     \
 193         "sd_bootcmd=echo Trying load from SD ..;"       \
 194                 "mmcinfo; mmc read $load_addr "         \
 195                 "$kernel_addr_sd $kernel_size_sd && "   \
 196                 "env exists secureboot && mmc read $kernelheader_addr_r "               \
 197                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 198                 " && esbc_validate ${kernelheader_addr_r};"     \
 199                 "bootm $load_addr#$board\0"
 200
 201 #endif
 202
 203 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 204
 205 #include <asm/arch/soc.h>
 206
 207 #endif /* __LS1046A_COMMON_H */