include/configs/ls1046a_common.h

   1 /*
   2  * Copyright 2016 Freescale Semiconductor
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1046A_COMMON_H
   8 #define __LS1046A_COMMON_H
   9
  10 /* SPL build */
  11 #ifdef CONFIG_SPL_BUILD
  12 #define SPL_NO_QBMAN
  13 #define SPL_NO_FMAN
  14 #define SPL_NO_ENV
  15 #define SPL_NO_MISC
  16 #define SPL_NO_QSPI
  17 #define SPL_NO_USB
  18 #define SPL_NO_SATA
  19 #endif
  20 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
  21 #define SPL_NO_MMC
  22 #endif
  23 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT))
  24 #define SPL_NO_IFC
  25 #endif
  26
  27 #define CONFIG_REMAKE_ELF
  28 #define CONFIG_FSL_LAYERSCAPE
  29 #define CONFIG_MP
  30 #define CONFIG_GICV2
  31
  32 #include <asm/arch/config.h>
  33 #include <asm/arch/stream_id_lsch2.h>
  34
  35 /* Link Definitions */
  36 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  37
  38 #define CONFIG_SUPPORT_RAW_INITRD
  39
  40 #define CONFIG_SKIP_LOWLEVEL_INIT
  41
  42 #define CONFIG_VERY_BIG_RAM
  43 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  44 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  45 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  46 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
  47
  48 #define CPU_RELEASE_ADDR               secondary_boot_func
  49
  50 /* Generic Timer Definitions */
  51 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  52
  53 /* Size of malloc() pool */
  54 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  55
  56 /* Serial Port */
  57 #define CONFIG_CONS_INDEX               1
  58 #define CONFIG_SYS_NS16550_SERIAL
  59 #define CONFIG_SYS_NS16550_REG_SIZE     1
  60 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  61
  62 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  63
  64 /* SD boot SPL */
  65 #ifdef CONFIG_SD_BOOT
  66 #define CONFIG_SPL_FRAMEWORK
  67 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  68 #define CONFIG_SPL_LIBCOMMON_SUPPORT
  69 #define CONFIG_SPL_LIBGENERIC_SUPPORT
  70 #define CONFIG_SPL_ENV_SUPPORT
  71 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
  72 #define CONFIG_SPL_WATCHDOG_SUPPORT
  73 #define CONFIG_SPL_I2C_SUPPORT
  74 #define CONFIG_SPL_SERIAL_SUPPORT
  75 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
  76
  77 #define CONFIG_SPL_MMC_SUPPORT
  78 #define CONFIG_SPL_TEXT_BASE            0x10000000
  79 #define CONFIG_SPL_MAX_SIZE             0x1f000         /* 124 KiB */
  80 #define CONFIG_SPL_STACK                0x10020000
  81 #define CONFIG_SPL_PAD_TO               0x21000         /* 132 KiB */
  82 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  83 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
  84 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  85                                         CONFIG_SPL_BSS_MAX_SIZE)
  86 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  87
  88 #ifdef CONFIG_SECURE_BOOT
  89 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
  90 /*
  91  * HDR would be appended at end of image and copied to DDR along
  92  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  93  * size increases then increase this size in case of secure boot as
  94  * it uses raw u-boot image instead of fit image.
  95  */
  96 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
  97 #else
  98 #define CONFIG_SYS_MONITOR_LEN          0x100000
  99 #endif /* ifdef CONFIG_SECURE_BOOT */
 100 #endif
 101
 102 /* NAND SPL */
 103 #ifdef CONFIG_NAND_BOOT
 104 #define CONFIG_SPL_PBL_PAD
 105 #define CONFIG_SPL_FRAMEWORK
 106 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
 107 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 108 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 109 #define CONFIG_SPL_ENV_SUPPORT
 110 #define CONFIG_SPL_WATCHDOG_SUPPORT
 111 #define CONFIG_SPL_I2C_SUPPORT
 112 #define CONFIG_SPL_SERIAL_SUPPORT
 113 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
 114
 115 #define CONFIG_SPL_NAND_SUPPORT
 116 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 117 #define CONFIG_SPL_TEXT_BASE            0x10000000
 118 #define CONFIG_SPL_MAX_SIZE             0x17000         /* 90 KiB */
 119 #define CONFIG_SPL_STACK                0x1001f000
 120 #define CONFIG_SYS_NAND_U_BOOT_DST      CONFIG_SYS_TEXT_BASE
 121 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 122
 123 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
 124 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 125 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
 126                                         CONFIG_SPL_BSS_MAX_SIZE)
 127 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 128 #define CONFIG_SYS_MONITOR_LEN          0xa0000
 129 #endif
 130
 131 /* I2C */
 132 #define CONFIG_SYS_I2C
 133 #define CONFIG_SYS_I2C_MXC
 134 #define CONFIG_SYS_I2C_MXC_I2C1
 135 #define CONFIG_SYS_I2C_MXC_I2C2
 136 #define CONFIG_SYS_I2C_MXC_I2C3
 137 #define CONFIG_SYS_I2C_MXC_I2C4
 138
 139 /* PCIe */
 140 #define CONFIG_PCIE1            /* PCIE controller 1 */
 141 #define CONFIG_PCIE2            /* PCIE controller 2 */
 142 #define CONFIG_PCIE3            /* PCIE controller 3 */
 143
 144 #ifdef CONFIG_PCI
 145 #define CONFIG_PCI_SCAN_SHOW
 146 #endif
 147
 148 /* Command line configuration */
 149
 150 /* MMC */
 151 #ifndef SPL_NO_MMC
 152 #ifdef CONFIG_MMC
 153 #define CONFIG_FSL_ESDHC
 154 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 155 #endif
 156 #endif
 157
 158 #ifndef SPL_NO_QBMAN
 159 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 160 #endif
 161
 162 /* FMan ucode */
 163 #ifndef SPL_NO_FMAN
 164 #define CONFIG_SYS_DPAA_FMAN
 165 #ifdef CONFIG_SYS_DPAA_FMAN
 166 #define CONFIG_SYS_FM_MURAM_SIZE        0x60000
 167 #endif
 168
 169 #ifdef CONFIG_SD_BOOT
 170 /*
 171  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 172  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 173  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
 174  */
 175 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 176 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x4800)
 177 #elif defined(CONFIG_QSPI_BOOT)
 178 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 179 #define CONFIG_SYS_FMAN_FW_ADDR         0x40900000
 180 #define CONFIG_ENV_SPI_BUS              0
 181 #define CONFIG_ENV_SPI_CS               0
 182 #define CONFIG_ENV_SPI_MAX_HZ           1000000
 183 #define CONFIG_ENV_SPI_MODE             0x03
 184 #elif defined(CONFIG_NAND_BOOT)
 185 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 186 #define CONFIG_SYS_FMAN_FW_ADDR         (72 * CONFIG_SYS_NAND_BLOCK_SIZE)
 187 #else
 188 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 189 #define CONFIG_SYS_FMAN_FW_ADDR         0x60900000
 190 #endif
 191 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 192 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 193 #endif
 194
 195 /* Miscellaneous configurable options */
 196 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 197
 198 #define CONFIG_HWCONFIG
 199 #define HWCONFIG_BUFFER_SIZE            128
 200
 201 #include <config_distro_defaults.h>
 202 #ifndef CONFIG_SPL_BUILD
 203 #define BOOT_TARGET_DEVICES(func) \
 204         func(MMC, mmc, 0) \
 205         func(USB, usb, 0)
 206 #include <config_distro_bootcmd.h>
 207 #endif
 208
 209 #ifndef SPL_NO_MISC
 210 /* Initial environment variables */
 211 #define CONFIG_EXTRA_ENV_SETTINGS               \
 212         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 213         "ramdisk_addr=0x800000\0"               \
 214         "ramdisk_size=0x2000000\0"              \
 215         "fdt_high=0xffffffffffffffff\0"         \
 216         "initrd_high=0xffffffffffffffff\0"      \
 217         "fdt_addr=0x64f00000\0"                 \
 218         "kernel_addr=0x65000000\0"              \
 219         "scriptaddr=0x80000000\0"               \
 220         "scripthdraddr=0x80080000\0"            \
 221         "fdtheader_addr_r=0x80100000\0"         \
 222         "kernelheader_addr_r=0x80200000\0"      \
 223         "load_addr=0xa0000000\0"            \
 224         "kernel_addr_r=0x81000000\0"            \
 225         "fdt_addr_r=0x90000000\0"               \
 226         "ramdisk_addr_r=0xa0000000\0"           \
 227         "kernel_start=0x1000000\0"              \
 228         "kernel_load=0xa0000000\0"              \
 229         "kernel_size=0x2800000\0"               \
 230         "console=ttyS0,115200\0"                \
 231                 MTDPARTS_DEFAULT "\0"           \
 232         BOOTENV                                 \
 233         "boot_scripts=ls1046ardb_boot.scr\0"    \
 234         "boot_script_hdr=hdr_ls1046ardb_bs.out\0"       \
 235         "scan_dev_for_boot_part="               \
 236                 "part list ${devtype} ${devnum} devplist; "   \
 237                 "env exists devplist || setenv devplist 1; "  \
 238                 "for distro_bootpart in ${devplist}; do "     \
 239                   "if fstype ${devtype} "                  \
 240                         "${devnum}:${distro_bootpart} "      \
 241                         "bootfstype; then "                  \
 242                         "run scan_dev_for_boot; "            \
 243                   "fi; "                                   \
 244                 "done\0"                                   \
 245         "scan_dev_for_boot="                              \
 246                 "echo Scanning ${devtype} "               \
 247                                 "${devnum}:${distro_bootpart}...; "  \
 248                 "for prefix in ${boot_prefixes}; do "     \
 249                         "run scan_dev_for_scripts; "      \
 250                 "done;"                                   \
 251                 "\0"                                      \
 252         "boot_a_script="                                  \
 253                 "load ${devtype} ${devnum}:${distro_bootpart} "  \
 254                         "${scriptaddr} ${prefix}${script}; "    \
 255                 "env exists secureboot && load ${devtype} "     \
 256                         "${devnum}:${distro_bootpart} "         \
 257                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 258                         "&& esbc_validate ${scripthdraddr};"    \
 259                 "source ${scriptaddr}\0"          \
 260         "installer=load mmc 0:2 $load_addr "          \
 261                 "/flex_installer_arm64.itb; "          \
 262                 "bootm $load_addr#ls1046ardb\0"  \
 263         "qspi_bootcmd=echo Trying load from qspi..;"      \
 264                 "sf probe && sf read $load_addr "         \
 265                 "$kernel_start $kernel_size && bootm $load_addr#$board\0"
 266
 267 #endif
 268
 269 /* Monitor Command Prompt */
 270 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 271 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 272                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 273 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE /* Boot args buffer */
 274 #define CONFIG_SYS_LONGHELP
 275
 276 #define CONFIG_AUTO_COMPLETE
 277 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 278
 279 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 280
 281 #include <asm/arch/soc.h>
 282
 283 #endif /* __LS1046A_COMMON_H */