include/configs/ls1021atsn.h

   1 /* SPDX-License-Identifier: GPL-2.0
   2  * Copyright 2016-2019 NXP
   3  * Copyright 2019 Vladimir Oltean <olteanv@gmail.com>
   4  */
   5
   6 #ifndef __CONFIG_H
   7 #define __CONFIG_H
   8
   9 #define CONFIG_SYS_INIT_RAM_ADDR        OCRAM_BASE_ADDR
  10 #define CONFIG_SYS_INIT_RAM_SIZE        OCRAM_SIZE
  11
  12 /* XHCI Support - enabled by default */
  13 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
  14
  15 #define DDR_SDRAM_CFG                   0x470c0008
  16 #define DDR_CS0_BNDS                    0x008000bf
  17 #define DDR_CS0_CONFIG                  0x80014302
  18 #define DDR_TIMING_CFG_0                0x50550004
  19 #define DDR_TIMING_CFG_1                0xbcb38c56
  20 #define DDR_TIMING_CFG_2                0x0040d120
  21 #define DDR_TIMING_CFG_3                0x010e1000
  22 #define DDR_TIMING_CFG_4                0x00000001
  23 #define DDR_TIMING_CFG_5                0x03401400
  24 #define DDR_SDRAM_CFG_2                 0x00401010
  25 #define DDR_SDRAM_MODE                  0x00061c60
  26 #define DDR_SDRAM_MODE_2                0x00180000
  27 #define DDR_SDRAM_INTERVAL              0x18600618
  28 #define DDR_DDR_WRLVL_CNTL              0x8655f605
  29 #define DDR_DDR_WRLVL_CNTL_2            0x05060607
  30 #define DDR_DDR_WRLVL_CNTL_3            0x05050505
  31 #define DDR_DDR_CDR1                    0x80040000
  32 #define DDR_DDR_CDR2                    0x00000001
  33 #define DDR_SDRAM_CLK_CNTL              0x02000000
  34 #define DDR_DDR_ZQ_CNTL                 0x89080600
  35 #define DDR_CS0_CONFIG_2                0
  36 #define DDR_SDRAM_CFG_MEM_EN            0x80000000
  37 #define SDRAM_CFG2_D_INIT               0x00000010
  38 #define DDR_CDR2_VREF_TRAIN_EN          0x00000080
  39 #define SDRAM_CFG2_FRC_SR               0x80000000
  40 #define SDRAM_CFG_BI                    0x00000001
  41
  42 #ifdef CONFIG_SD_BOOT
  43 #ifdef CONFIG_NXP_ESBC
  44 #define CONFIG_U_BOOT_HDR_SIZE          (16 << 10)
  45 #endif /* ifdef CONFIG_NXP_ESBC */
  46
  47 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SYS_TEXT_BASE + \
  48                 CONFIG_SYS_MONITOR_LEN)
  49 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  50 #define CONFIG_SPL_BSS_START_ADDR       0x80100000
  51
  52 #ifdef CONFIG_U_BOOT_HDR_SIZE
  53 /*
  54  * HDR would be appended at end of image and copied to DDR along
  55  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  56  * size increases then increase this size in case of secure boot as
  57  * it uses raw U-Boot image instead of FIT image.
  58  */
  59 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
  60 #else
  61 #define CONFIG_SYS_MONITOR_LEN          0x100000
  62 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
  63 #endif
  64
  65 #define PHYS_SDRAM                      0x80000000
  66 #define PHYS_SDRAM_SIZE                 (1u * 1024 * 1024 * 1024)
  67
  68 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000UL
  69 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  70
  71 /* Serial Port */
  72 #define CONFIG_SYS_NS16550_SERIAL
  73 #ifndef CONFIG_DM_SERIAL
  74 #define CONFIG_SYS_NS16550_REG_SIZE     1
  75 #endif
  76 #define CONFIG_SYS_NS16550_CLK          get_serial_clock()
  77
  78 /* I2C */
  79
  80 /* EEPROM */
  81 #define CONFIG_SYS_I2C_EEPROM_NXID
  82 #define CONFIG_SYS_EEPROM_BUS_NUM       0
  83
  84 /* QSPI */
  85 #define FSL_QSPI_FLASH_SIZE             (1 << 24)
  86 #define FSL_QSPI_FLASH_NUM              2
  87
  88 /* PCIe */
  89 #define CONFIG_PCIE1                    /* PCIE controller 1 */
  90 #define CONFIG_PCIE2                    /* PCIE controller 2 */
  91 #define FSL_PCIE_COMPAT                 "fsl,ls1021a-pcie"
  92 #ifdef CONFIG_PCI
  93 #define CONFIG_PCI_SCAN_SHOW
  94 #endif
  95
  96 #define CONFIG_LAYERSCAPE_NS_ACCESS
  97
  98 #define CONFIG_HWCONFIG
  99 #define HWCONFIG_BUFFER_SIZE            256
 100
 101 #define CONFIG_FSL_DEVICE_DISABLE
 102
 103 #define BOOT_TARGET_DEVICES(func) \
 104         func(MMC, mmc, 0) \
 105         func(USB, usb, 0) \
 106         func(DHCP, dhcp, na)
 107 #include <config_distro_bootcmd.h>
 108
 109 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 110         "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0"             \
 111         "initrd_high=0xffffffff\0"                                      \
 112         "kernel_addr=0x61000000\0"                                      \
 113         "kernelheader_addr=0x60800000\0"                                \
 114         "scriptaddr=0x80000000\0"                                       \
 115         "scripthdraddr=0x80080000\0"                                    \
 116         "fdtheader_addr_r=0x80100000\0"                                 \
 117         "kernelheader_addr_r=0x80200000\0"                              \
 118         "kernel_addr_r=0x80008000\0"                                    \
 119         "kernelheader_size=0x40000\0"                                   \
 120         "fdt_addr_r=0x8f000000\0"                                       \
 121         "ramdisk_addr_r=0xa0000000\0"                                   \
 122         "load_addr=0x80008000\0"                                        \
 123         "kernel_size=0x2800000\0"                                       \
 124         "kernel_addr_sd=0x8000\0"                                       \
 125         "kernel_size_sd=0x14000\0"                                      \
 126         "kernelhdr_addr_sd=0x4000\0"                                    \
 127         "kernelhdr_size_sd=0x10\0"                                      \
 128         BOOTENV                                                         \
 129         "boot_scripts=ls1021atsn_boot.scr\0"                            \
 130         "boot_script_hdr=hdr_ls1021atsn_bs.out\0"                       \
 131                 "scan_dev_for_boot_part="                               \
 132                         "part list ${devtype} ${devnum} devplist; "     \
 133                         "env exists devplist || setenv devplist 1; "    \
 134                         "for distro_bootpart in ${devplist}; do "       \
 135                         "if fstype ${devtype} "                         \
 136                                 "${devnum}:${distro_bootpart} "         \
 137                                 "bootfstype; then "                     \
 138                                 "run scan_dev_for_boot; "               \
 139                         "fi; "                                          \
 140                 "done\0"                                                \
 141         "scan_dev_for_boot="                                            \
 142                 "echo Scanning ${devtype} "                             \
 143                                 "${devnum}:${distro_bootpart}...; "     \
 144                 "for prefix in ${boot_prefixes}; do "                   \
 145                         "run scan_dev_for_scripts; "                    \
 146                         "run scan_dev_for_extlinux; "                   \
 147                 "done;"                                                 \
 148                 "\0"                                                    \
 149         "boot_a_script="                                                \
 150                 "load ${devtype} ${devnum}:${distro_bootpart} "         \
 151                         "${scriptaddr} ${prefix}${script}; "            \
 152                 "env exists secureboot && load ${devtype} "             \
 153                         "${devnum}:${distro_bootpart} "                 \
 154                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 155                         "&& esbc_validate ${scripthdraddr};"            \
 156                 "source ${scriptaddr}\0"                                \
 157         "qspi_bootcmd=echo Trying load from qspi..;"                    \
 158                 "sf probe && sf read $load_addr "                       \
 159                 "$kernel_addr $kernel_size; env exists secureboot "     \
 160                 "&& sf read $kernelheader_addr_r $kernelheader_addr "   \
 161                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 162                 "bootm $load_addr#$board\0"                             \
 163         "sd_bootcmd=echo Trying load from SD ..;"                       \
 164                 "mmcinfo && mmc read $load_addr "                       \
 165                 "$kernel_addr_sd $kernel_size_sd && "                   \
 166                 "env exists secureboot && mmc read $kernelheader_addr_r " \
 167                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 168                 " && esbc_validate ${kernelheader_addr_r};"             \
 169                 "bootm $load_addr#$board\0"
 170
 171 /* Miscellaneous configurable options */
 172 #define CONFIG_SYS_BOOTMAPSZ            (256 << 20)
 173
 174 #define CONFIG_LS102XA_STREAM_ID
 175
 176 /* Environment */
 177
 178 #define CONFIG_SYS_BOOTM_LEN            0x8000000 /* 128 MB */
 179
 180 #endif