1 /* SPDX-License-Identifier: GPL-2.0+ */
3 * Copyright 2022 Marek Vasut <marex@denx.de>
6 #ifndef __IMX8MP_DHCOM_PDK2_H
7 #define __IMX8MP_DHCOM_PDK2_H
9 #include <linux/sizes.h>
10 #include <linux/stringify.h>
11 #include <asm/arch/imx-regs.h>
13 #define CONFIG_SYS_BOOTM_LEN SZ_128M
15 #define CONFIG_SYS_MONITOR_LEN SZ_1M
17 #ifdef CONFIG_SPL_BUILD
18 #define CONFIG_SPL_BSS_START_ADDR 0x0096FC00
19 #define CONFIG_SYS_SPL_MALLOC_START 0x4c000000
20 #define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K /* 512 kiB */
22 /* For RAW image gives a error info not panic */
23 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
27 /* Link Definitions */
28 #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
29 #define CONFIG_SYS_INIT_RAM_SIZE 0x200000
31 #define CONFIG_SYS_SDRAM_BASE 0x40000000
32 #define PHYS_SDRAM 0x40000000
33 #define PHYS_SDRAM_SIZE 0x20000000 /* Minimum 512 MiB DDR */
35 #define CONFIG_MXC_UART_BASE UART1_BASE_ADDR
37 /* PHY needs a longer autonegotiation timeout after reset */
38 #define PHY_ANEG_TIMEOUT 20000
39 #define FEC_QUIRK_ENET_MAC
42 #define CONFIG_SYS_FSL_USDHC_NUM 2
43 #define CONFIG_SYS_FSL_ESDHC_ADDR 0
45 #if !defined(CONFIG_SPL_BUILD)
47 #define CONFIG_EXTRA_ENV_SETTINGS \
48 "altbootcmd=run bootcmd ; reset\0" \
50 "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
51 "pxefile_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
52 "ramdisk_addr_r=0x58000000\0" \
53 "scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
54 /* Give slow devices beyond USB HUB chance to come up. */ \
55 "usb_pgood_delay=2000\0" \
57 /* RAM block at DRAM offset 256..768 MiB */ \
58 "ram ram0=ram ram 0x50000000 0x20000000&" \
59 /* 16 MiB SPI NOR */ \
60 "mtd nor0=sf raw 0x0 0x1000000\0" \
62 "setenv dh_update_env true ; saveenv ; saveenv\0" \
63 "dh_update_sf_gen_fcfb=" \
64 "setexpr sfaddr ${loadaddr} - 0x1000 ; " \
67 "mw 0x400 0x42464346 ; " \
68 "mw 0x404 0x56010000 ; " \
69 "mw 0x40c 00030300 ; " \
70 "mw 0x444 0x00020101 ; " \
71 "mw 0x450 0x10000000 ; " \
72 "mw 0x480 0x0818040b ; " \
73 "mw 0x484 0x24043008 ; " \
75 "mw 0x5c4 0x10000 ; " \
77 "dh_update_sf_write_data=" \
78 "setexpr sfaddr ${loadaddr} - 0x1000 ; " \
79 "setexpr filesize ${filesize} + 0x1000 ; " \
80 "sf probe && sf update ${sfaddr} 0 ${filesize}\0" \
81 "dh_update_sd_to_sf=" \
82 "load mmc 0:1 ${loadaddr} boot/flash.bin && " \
83 "run dh_update_sf_gen_fcfb dh_update_sf_write_data\0" \
84 "dh_update_emmc_to_sf=" \
85 "load mmc 1:1 ${loadaddr} boot/flash.bin && " \
86 "run dh_update_sf_gen_fcfb dh_update_sf_write_data\0" \
89 #define BOOT_TARGET_DEVICES(func) \
95 #include <config_distro_bootcmd.h>