include/configs/cm5200.h

   1 /*
   2  * (C) Copyright 2003-2007
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 /*
  12  * High Level Configuration Options
  13  */
  14 #define CONFIG_MPC5200          1       /* This is an MPC5200 CPU */
  15 #define CONFIG_CM5200           1       /* ... on CM5200 platform */
  16
  17 #define CONFIG_SYS_TEXT_BASE    0xfc000000
  18
  19 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
  20
  21 /*
  22  * Supported commands
  23  */
  24 #define CONFIG_CMD_BSP
  25 #define CONFIG_CMD_DATE
  26 #define CONFIG_CMD_DIAG
  27 #define CONFIG_CMD_JFFS2
  28 #define CONFIG_CMD_REGINFO
  29
  30 /*
  31  * Serial console configuration
  32  */
  33 #define CONFIG_PSC_CONSOLE      1       /* console is on PSC1 */
  34 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  35
  36 /*
  37  * Ethernet configuration
  38  */
  39 #define CONFIG_MPC5xxx_FEC      1
  40 #define CONFIG_MPC5xxx_FEC_MII100
  41 #define CONFIG_PHY_ADDR         0x00
  42 #define CONFIG_ENV_OVERWRITE    1       /* allow overwriting of ethaddr */
  43 /* use misc_init_r() to read ethaddr from I2C EEPROM (see CONFIG_SYS_I2C_EEPROM) */
  44 #define CONFIG_MISC_INIT_R      1
  45 #define CONFIG_MAC_OFFSET       0x35    /* MAC address offset in I2C EEPROM */
  46
  47 /*
  48  * POST support
  49  */
  50 #define CONFIG_POST             (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
  51 #define MPC5XXX_SRAM_POST_SIZE  (MPC5XXX_SRAM_SIZE - 4)
  52 /* List of I2C addresses to be verified by POST */
  53 #define CONFIG_SYS_POST_I2C_ADDRS       {CONFIG_SYS_I2C_SLAVE,  \
  54                                          CONFIG_SYS_I2C_IO,     \
  55                                          CONFIG_SYS_I2C_EEPROM}
  56
  57 /* display image timestamps */
  58 #define CONFIG_TIMESTAMP        1
  59
  60 /*
  61  * Autobooting
  62  */
  63 #define CONFIG_PREBOOT  "echo;" \
  64         "echo Type \"run net_nfs_fdt\" to mount root filesystem over NFS;" \
  65         "echo"
  66 #undef CONFIG_BOOTARGS
  67
  68 /*
  69  * Default environment settings
  70  */
  71 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  72         "netdev=eth0\0"                                                 \
  73         "netmask=255.255.0.0\0"                                         \
  74         "ipaddr=192.168.160.33\0"                                       \
  75         "serverip=192.168.1.1\0"                                        \
  76         "gatewayip=192.168.1.1\0"                                       \
  77         "console=ttyPSC0\0"                                             \
  78         "u-boot_addr=100000\0"                                          \
  79         "kernel_addr=200000\0"                                          \
  80         "kernel_addr_flash=fc0c0000\0"                                  \
  81         "fdt_addr=400000\0"                                             \
  82         "fdt_addr_flash=fc0a0000\0"                                     \
  83         "ramdisk_addr=500000\0"                                         \
  84         "rootpath=/opt/eldk-4.1/ppc_6xx\0"                              \
  85         "u-boot=/tftpboot/cm5200/u-boot.bin\0"                          \
  86         "bootfile_fdt=/tftpboot/cm5200/uImage\0"                        \
  87         "fdt_file=/tftpboot/cm5200/cm5200.dtb\0"                        \
  88         "load=tftp ${u-boot_addr} ${u-boot}\0"                          \
  89         "update=prot off fc000000 +${filesize}; "                       \
  90                 "era fc000000 +${filesize}; "                           \
  91                 "cp.b ${u-boot_addr} fc000000 ${filesize}; "            \
  92                 "prot on fc000000 +${filesize}\0"                       \
  93         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
  94                 "nfsroot=${serverip}:${rootpath}\0"                     \
  95         "flashargs=setenv bootargs root=/dev/mtdblock5 rw\0"            \
  96         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
  97         "addinit=setenv bootargs ${bootargs} init=/linuxrc\0"           \
  98         "addcons=setenv bootargs ${bootargs} "                          \
  99                 "console=${console},${baudrate}\0"                      \
 100         "addip=setenv bootargs ${bootargs} "                            \
 101                 "ip=${ipaddr}:${serverip}:${gatewayip}:"                \
 102                 "${netmask}:${hostname}:${netdev}:off panic=1\0"        \
 103         "flash_flash=run flashargs addinit addip addcons;"              \
 104                 "bootm ${kernel_addr_flash} - ${fdt_addr_flash}\0"      \
 105         "net_nfs_fdt=tftp ${kernel_addr} ${bootfile_fdt}; "             \
 106                 "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip "      \
 107                 "addcons; bootm ${kernel_addr} - ${fdt_addr}\0"         \
 108         ""
 109 #define CONFIG_BOOTCOMMAND      "run flash_flash"
 110
 111 /*
 112  * Low level configuration
 113  */
 114
 115 /*
 116  * Clock configuration
 117  */
 118 #define CONFIG_SYS_MPC5XXX_CLKIN        33000000        /* SYS_XTAL_IN = 33MHz */
 119 #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK 1       /* IPB = 133MHz */
 120
 121 /*
 122  * Memory map
 123  */
 124 #define CONFIG_SYS_MBAR         0xF0000000
 125 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 126 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000
 127
 128 #define CONFIG_SYS_LOWBOOT              1
 129
 130 /* Use ON-Chip SRAM until RAM will be available */
 131 #define CONFIG_SYS_INIT_RAM_ADDR        MPC5XXX_SRAM
 132 #ifdef CONFIG_POST
 133 /* preserve space for the post_word at end of on-chip SRAM */
 134 #define CONFIG_SYS_INIT_RAM_SIZE        MPC5XXX_SRAM_POST_SIZE
 135 #else
 136 #define CONFIG_SYS_INIT_RAM_SIZE        MPC5XXX_SRAM_SIZE
 137 #endif
 138
 139 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 140 #define CONFIG_BOARD_TYPES      1       /* we use board_type */
 141
 142 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 143
 144 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 145 #define CONFIG_SYS_MONITOR_LEN          (384 << 10)     /* 384 kB for Monitor */
 146 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* 256 kB for malloc() */
 147 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* initial mem map for Linux */
 148
 149 /*
 150  * Flash configuration
 151  */
 152 #define CONFIG_SYS_FLASH_CFI            1
 153 #define CONFIG_FLASH_CFI_DRIVER 1
 154 #define CONFIG_SYS_FLASH_BASE           0xfc000000
 155 /* we need these despite using CFI */
 156 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of flash banks */
 157 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max num of sectors on one chip */
 158 #define CONFIG_SYS_FLASH_SIZE           0x02000000 /* 32 MiB */
 159
 160 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 161 #define CONFIG_SYS_RAMBOOT              1
 162 #undef CONFIG_SYS_LOWBOOT
 163 #endif
 164
 165 /*
 166  * Chip selects configuration
 167  */
 168 /* Boot Chipselect */
 169 #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
 170 #define CONFIG_SYS_BOOTCS_SIZE          CONFIG_SYS_FLASH_SIZE
 171 #define CONFIG_SYS_BOOTCS_CFG           0x00087D31      /* for pci_clk = 33 MHz */
 172 /* use board_early_init_r to enable flash write in CS_BOOT */
 173 #define CONFIG_BOARD_EARLY_INIT_R
 174
 175 /* Flash memory addressing */
 176 #define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
 177 #define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
 178
 179 /* No burst, dead cycle = 1 for CS0 (Flash) */
 180 #define CONFIG_SYS_CS_BURST             0x00000000
 181 #define CONFIG_SYS_CS_DEADCYCLE 0x00000001
 182
 183 /*
 184  * SDRAM configuration
 185  * settings for k4s561632E-xx75, assuming XLB = 132 MHz
 186  */
 187 #define SDRAM_MODE      0x00CD0000      /* CASL 3, burst length 8 */
 188 #define SDRAM_CONTROL   0x514F0000
 189 #define SDRAM_CONFIG1   0xE2333900
 190 #define SDRAM_CONFIG2   0x8EE70000
 191
 192 /*
 193  * MTD configuration
 194  */
 195 #define CONFIG_CMD_MTDPARTS     1
 196 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 197 #define CONFIG_FLASH_CFI_MTD
 198 #define MTDIDS_DEFAULT          "nor0=cm5200-0"
 199 #define MTDPARTS_DEFAULT        "mtdparts=cm5200-0:"                    \
 200                                         "384k(uboot),128k(env),"        \
 201                                         "128k(redund_env),128k(dtb),"   \
 202                                         "2m(kernel),27904k(rootfs),"    \
 203                                         "-(config)"
 204
 205 /*
 206  * I2C configuration
 207  */
 208 #define CONFIG_HARD_I2C         1       /* I2C with hardware support */
 209 #define CONFIG_SYS_I2C_MODULE           2       /* Select I2C module #2 */
 210 #define CONFIG_SYS_I2C_SPEED            40000   /* 40 kHz */
 211 #define CONFIG_SYS_I2C_SLAVE            0x0
 212 #define CONFIG_SYS_I2C_IO               0x38    /* PCA9554AD I2C I/O port address */
 213 #define CONFIG_SYS_I2C_EEPROM           0x53    /* I2C EEPROM device address */
 214
 215 /*
 216  * RTC configuration
 217  */
 218 #define CONFIG_RTC_MPC5200      1       /* use internal MPC5200 RTC */
 219
 220 /*
 221  * USB configuration
 222  */
 223 #define CONFIG_USB_OHCI         1
 224 #define CONFIG_USB_CLOCK        0x0001BBBB
 225 #define CONFIG_USB_CONFIG       0x00001000
 226 /* Partitions (for USB) */
 227
 228 /*
 229  * Invoke our last_stage_init function - needed by fwupdate
 230  */
 231 #define CONFIG_LAST_STAGE_INIT  1
 232
 233 /*
 234  * Environment settings
 235  */
 236 #define CONFIG_ENV_IS_IN_FLASH  1
 237 #define CONFIG_ENV_SIZE         0x10000
 238 #define CONFIG_ENV_SECT_SIZE    0x20000
 239 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
 240 /* Configuration of redundant environment */
 241 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 242 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 243
 244 /*
 245  * Pin multiplexing configuration
 246  */
 247
 248 /*
 249  * CS1/GPIO_WKUP_6: GPIO (default)
 250  * ALTs: CAN1 on I2C1, CAN2 on TIMER0/1
 251  * IRDA/PSC6: UART
 252  * Ether: Ethernet 100Mbit with MD
 253  * PCI_DIS: PCI controller disabled
 254  * USB: USB
 255  * PSC3: SPI with UART3
 256  * PSC2: UART
 257  * PSC1: UART
 258  */
 259 #define CONFIG_SYS_GPS_PORT_CONFIG      0x10559C44
 260
 261 /*
 262  * Miscellaneous configurable options
 263  */
 264 #define CONFIG_SYS_LONGHELP             1       /* undef to save memory */
 265 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 266 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 267 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 268 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 269
 270 #define CONFIG_SYS_ALT_MEMTEST          1
 271 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 272 #define CONFIG_SYS_MEMTEST_END          0x03f00000      /* 1 .. 63 MiB in SDRAM */
 273
 274 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 275
 276 /*
 277  * Various low-level settings
 278  */
 279 #define CONFIG_SYS_HID0_INIT            HID0_ICE | HID0_ICFI
 280 #define CONFIG_SYS_HID0_FINAL           HID0_ICE
 281
 282 #define CONFIG_SYS_XLB_PIPELINING       1       /* enable transaction pipeling */
 283
 284 /*
 285  * Cache Configuration
 286  */
 287 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC5xxx CPUs */
 288 #ifdef CONFIG_CMD_KGDB
 289 #define CONFIG_SYS_CACHELINE_SHIFT      5       /* log base 2 of the above value */
 290 #endif
 291
 292 /*
 293  * Flat Device Tree support
 294  */
 295 #define OF_CPU                  "PowerPC,5200@0"
 296 #define OF_SOC                  "soc5200@f0000000"
 297 #define OF_TBCLK                (bd->bi_busfreq / 4)
 298 #define OF_STDOUT_PATH          "/soc5200@f0000000/serial@2000"
 299
 300 #endif /* __CONFIG_H */