include/configs/caddy2.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * esd vme8349 U-Boot configuration file
   4  * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
   5  *
   6  * (C) Copyright 2006-2010
   7  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   8  *
   9  * reinhard.arlt@esd-electronics.de
  10  * Based on the MPC8349EMDS config.
  11  */
  12
  13 /*
  14  * vme8349 board configuration file.
  15  */
  16
  17 #ifndef __CONFIG_H
  18 #define __CONFIG_H
  19
  20 /*
  21  * High Level Configuration Options
  22  */
  23 #define CONFIG_E300             1       /* E300 Family */
  24
  25 /* Don't enable PCI2 on vme834x - it doesn't exist physically. */
  26 #undef CONFIG_MPC83XX_PCI2              /* support for 2nd PCI controller */
  27
  28 #define CONFIG_PCI_66M
  29 #ifdef CONFIG_PCI_66M
  30 #define CONFIG_83XX_CLKIN       66000000        /* in Hz */
  31 #else
  32 #define CONFIG_83XX_CLKIN       33000000        /* in Hz */
  33 #endif
  34
  35 #ifndef CONFIG_SYS_CLK_FREQ
  36 #ifdef CONFIG_PCI_66M
  37 #define CONFIG_SYS_CLK_FREQ     66000000
  38 #define HRCWL_CSB_TO_CLKIN      HRCWL_CSB_TO_CLKIN_4X1
  39 #else
  40 #define CONFIG_SYS_CLK_FREQ     33000000
  41 #define HRCWL_CSB_TO_CLKIN      HRCWL_CSB_TO_CLKIN_8X1
  42 #endif
  43 #endif
  44
  45 #define CONFIG_SYS_IMMR         0xE0000000
  46
  47 #undef CONFIG_SYS_DRAM_TEST                     /* memory test, takes time */
  48 #define CONFIG_SYS_MEMTEST_START        0x00000000      /* memtest region */
  49 #define CONFIG_SYS_MEMTEST_END          0x00100000
  50
  51 /*
  52  * DDR Setup
  53  */
  54 #define CONFIG_DDR_ECC                  /* only for ECC DDR module */
  55 #define CONFIG_DDR_ECC_CMD              /* use DDR ECC user commands */
  56 #define CONFIG_SPD_EEPROM
  57 #define SPD_EEPROM_ADDRESS              0x54
  58 #define CONFIG_SYS_READ_SPD             vme8349_read_spd
  59 #define CONFIG_SYS_83XX_DDR_USES_CS0    /* esd; Fsl board uses CS2/CS3 */
  60
  61 /*
  62  * 32-bit data path mode.
  63  *
  64  * Please note that using this mode for devices with the real density of 64-bit
  65  * effectively reduces the amount of available memory due to the effect of
  66  * wrapping around while translating address to row/columns, for example in the
  67  * 256MB module the upper 128MB get aliased with contents of the lower
  68  * 128MB); normally this define should be used for devices with real 32-bit
  69  * data path.
  70  */
  71 #undef CONFIG_DDR_32BIT
  72
  73 #define CONFIG_SYS_DDR_BASE             0x00000000      /* DDR is sys memory*/
  74 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  75 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  76 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN \
  77                                         | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
  78 #define CONFIG_DDR_2T_TIMING
  79 #define CONFIG_SYS_DDRCDR               (DDRCDR_DHC_EN \
  80                                         | DDRCDR_ODT \
  81                                         | DDRCDR_Q_DRN)
  82                                         /* 0x80080001 */
  83
  84 /*
  85  * FLASH on the Local Bus
  86  */
  87 #define CONFIG_SYS_FLASH_BASE           0xffc00000      /* start of FLASH   */
  88 #define CONFIG_SYS_FLASH_SIZE           4               /* flash size in MB */
  89 #define CONFIG_SYS_BR0_PRELIM           (CONFIG_SYS_FLASH_BASE | \
  90                                          BR_PS_16 |     /*  16bit */ \
  91                                          BR_MS_GPCM |   /*  MSEL = GPCM */ \
  92                                          BR_V)          /* valid */
  93
  94 #define CONFIG_SYS_OR0_PRELIM           (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
  95                                         | OR_GPCM_XAM \
  96                                         | OR_GPCM_CSNT \
  97                                         | OR_GPCM_ACS_DIV2 \
  98                                         | OR_GPCM_XACS \
  99                                         | OR_GPCM_SCY_15 \
 100                                         | OR_GPCM_TRLX_SET \
 101                                         | OR_GPCM_EHTR_SET \
 102                                         | OR_GPCM_EAD)
 103                                         /* 0xffc06ff7 */
 104 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 105 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_4MB)
 106
 107 #define CONFIG_SYS_WINDOW1_BASE         0xf0000000
 108 #define CONFIG_SYS_BR1_PRELIM           (CONFIG_SYS_WINDOW1_BASE \
 109                                         | BR_PS_32 \
 110                                         | BR_MS_GPCM \
 111                                         | BR_V)
 112                                         /* 0xF0001801 */
 113 #define CONFIG_SYS_OR1_PRELIM           (OR_AM_256KB \
 114                                         | OR_GPCM_SETA)
 115                                         /* 0xfffc0208 */
 116 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_WINDOW1_BASE
 117 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_256KB)
 118
 119 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 120 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device*/
 121
 122 #undef CONFIG_SYS_FLASH_CHECKSUM
 123 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase TO (ms) */
 124 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write TO (ms) */
 125
 126 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 127
 128 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 129 #define CONFIG_SYS_RAMBOOT
 130 #else
 131 #undef CONFIG_SYS_RAMBOOT
 132 #endif
 133
 134 #define CONFIG_SYS_INIT_RAM_LOCK        1
 135 #define CONFIG_SYS_INIT_RAM_ADDR        0xF7000000      /* Initial RAM addr */
 136 #define CONFIG_SYS_INIT_RAM_SIZE                0x1000          /* size */
 137
 138 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 139                                          GENERATED_GBL_DATA_SIZE)
 140 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 141
 142 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Reserve 256 kB */
 143 #define CONFIG_SYS_MALLOC_LEN           (256 * 1024)    /* Malloc size */
 144
 145 /*
 146  * Local Bus LCRR and LBCR regs
 147  *    LCRR:  no DLL bypass, Clock divider is 4
 148  * External Local Bus rate is
 149  *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
 150  */
 151 #define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_4
 152 #define CONFIG_SYS_LBC_LBCR     0x00000000
 153
 154 #undef CONFIG_SYS_LB_SDRAM      /* if board has SDRAM on local bus */
 155
 156 /*
 157  * Serial Port
 158  */
 159 #define CONFIG_SYS_NS16550_SERIAL
 160 #define CONFIG_SYS_NS16550_REG_SIZE     1
 161 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 162
 163 #define CONFIG_SYS_BAUDRATE_TABLE  \
 164                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 165
 166 #define CONFIG_SYS_NS16550_COM1         (CONFIG_SYS_IMMR + 0x4500)
 167 #define CONFIG_SYS_NS16550_COM2         (CONFIG_SYS_IMMR + 0x4600)
 168
 169 /* I2C */
 170 #define CONFIG_SYS_I2C
 171 #define CONFIG_SYS_I2C_FSL
 172 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 173 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 174 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 175 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 176 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 177 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 178 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 179 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
 180
 181 #define CONFIG_SYS_I2C_8574_ADDR2       0x20    /* I2C1, PCF8574 */
 182
 183 /* TSEC */
 184 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 185 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
 186 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 187 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
 188
 189 /*
 190  * General PCI
 191  * Addresses are mapped 1-1.
 192  */
 193 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 194 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 195 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 196 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 197 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 198 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
 199 #define CONFIG_SYS_PCI1_IO_BASE         0x00000000
 200 #define CONFIG_SYS_PCI1_IO_PHYS         0xE2000000
 201 #define CONFIG_SYS_PCI1_IO_SIZE         0x00100000      /* 1M */
 202
 203 #define CONFIG_SYS_PCI2_MEM_BASE        0xA0000000
 204 #define CONFIG_SYS_PCI2_MEM_PHYS        CONFIG_SYS_PCI2_MEM_BASE
 205 #define CONFIG_SYS_PCI2_MEM_SIZE        0x10000000      /* 256M */
 206 #define CONFIG_SYS_PCI2_MMIO_BASE       0xB0000000
 207 #define CONFIG_SYS_PCI2_MMIO_PHYS       CONFIG_SYS_PCI2_MMIO_BASE
 208 #define CONFIG_SYS_PCI2_MMIO_SIZE       0x10000000      /* 256M */
 209 #define CONFIG_SYS_PCI2_IO_BASE         0x00000000
 210 #define CONFIG_SYS_PCI2_IO_PHYS         0xE2100000
 211 #define CONFIG_SYS_PCI2_IO_SIZE         0x00100000      /* 1M */
 212
 213 #if defined(CONFIG_PCI)
 214
 215 #define PCI_64BIT
 216 #define PCI_ONE_PCI1
 217 #if defined(PCI_64BIT)
 218 #undef PCI_ALL_PCI1
 219 #undef PCI_TWO_PCI1
 220 #undef PCI_ONE_PCI1
 221 #endif
 222
 223 #undef CONFIG_EEPRO100
 224 #undef CONFIG_TULIP
 225
 226 #if !defined(CONFIG_PCI_PNP)
 227         #define PCI_ENET0_IOADDR        0xFIXME
 228         #define PCI_ENET0_MEMADDR       0xFIXME
 229         #define PCI_IDSEL_NUMBER        0xFIXME
 230 #endif
 231
 232 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 233 #define CONFIG_SYS_PCI_SUBSYS_VENDORID  0x1957  /* Freescale */
 234
 235 #endif  /* CONFIG_PCI */
 236
 237 /*
 238  * TSEC configuration
 239  */
 240
 241 #if defined(CONFIG_TSEC_ENET)
 242
 243 #define CONFIG_GMII                     /* MII PHY management */
 244 #define CONFIG_TSEC1
 245 #define CONFIG_TSEC1_NAME       "TSEC0"
 246 #define CONFIG_TSEC2
 247 #define CONFIG_TSEC2_NAME       "TSEC1"
 248 #define CONFIG_PHY_M88E1111
 249 #define TSEC1_PHY_ADDR          0x08
 250 #define TSEC2_PHY_ADDR          0x10
 251 #define TSEC1_PHYIDX            0
 252 #define TSEC2_PHYIDX            0
 253 #define TSEC1_FLAGS             TSEC_GIGABIT
 254 #define TSEC2_FLAGS             TSEC_GIGABIT
 255
 256 /* Options are: TSEC[0-1] */
 257 #define CONFIG_ETHPRIME         "TSEC0"
 258
 259 #endif  /* CONFIG_TSEC_ENET */
 260
 261 /*
 262  * Environment
 263  */
 264 #ifndef CONFIG_SYS_RAMBOOT
 265         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + 0xc0000)
 266         #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 267         #define CONFIG_ENV_SIZE         0x2000
 268
 269 /* Address and size of Redundant Environment Sector     */
 270 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 271 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 272
 273 #else
 274         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 275         #define CONFIG_ENV_SIZE         0x2000
 276 #endif
 277
 278 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 279 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 280
 281 /*
 282  * BOOTP options
 283  */
 284 #define CONFIG_BOOTP_BOOTFILESIZE
 285
 286 /*
 287  * Command line configuration.
 288  */
 289 #define CONFIG_SYS_RTC_BUS_NUM  0x01
 290 #define CONFIG_SYS_I2C_RTC_ADDR 0x32
 291 #define CONFIG_RTC_RX8025
 292
 293 /* Pass Ethernet MAC to VxWorks */
 294 #define CONFIG_SYS_VXWORKS_MAC_PTR      0x000043f0
 295
 296 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 297
 298 /*
 299  * Miscellaneous configurable options
 300  */
 301 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 302
 303 /*
 304  * For booting Linux, the board info and command line data
 305  * have to be in the first 256 MB of memory, since this is
 306  * the maximum mapped by the Linux kernel during initialization.
 307  */
 308 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Init Memory map for Linux*/
 309
 310 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 311
 312 #define CONFIG_SYS_HRCW_LOW (\
 313         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 314         HRCWL_DDR_TO_SCB_CLK_1X1 |\
 315         HRCWL_CSB_TO_CLKIN |\
 316         HRCWL_VCO_1X2 |\
 317         HRCWL_CORE_TO_CSB_2X1)
 318
 319 #if defined(PCI_64BIT)
 320 #define CONFIG_SYS_HRCW_HIGH (\
 321         HRCWH_PCI_HOST |\
 322         HRCWH_64_BIT_PCI |\
 323         HRCWH_PCI1_ARBITER_ENABLE |\
 324         HRCWH_PCI2_ARBITER_DISABLE |\
 325         HRCWH_CORE_ENABLE |\
 326         HRCWH_FROM_0X00000100 |\
 327         HRCWH_BOOTSEQ_DISABLE |\
 328         HRCWH_SW_WATCHDOG_DISABLE |\
 329         HRCWH_ROM_LOC_LOCAL_16BIT |\
 330         HRCWH_TSEC1M_IN_GMII |\
 331         HRCWH_TSEC2M_IN_GMII)
 332 #else
 333 #define CONFIG_SYS_HRCW_HIGH (\
 334         HRCWH_PCI_HOST |\
 335         HRCWH_32_BIT_PCI |\
 336         HRCWH_PCI1_ARBITER_ENABLE |\
 337         HRCWH_PCI2_ARBITER_ENABLE |\
 338         HRCWH_CORE_ENABLE |\
 339         HRCWH_FROM_0X00000100 |\
 340         HRCWH_BOOTSEQ_DISABLE |\
 341         HRCWH_SW_WATCHDOG_DISABLE |\
 342         HRCWH_ROM_LOC_LOCAL_16BIT |\
 343         HRCWH_TSEC1M_IN_GMII |\
 344         HRCWH_TSEC2M_IN_GMII)
 345 #endif
 346
 347 /* System IO Config */
 348 #define CONFIG_SYS_SICRH 0
 349 #define CONFIG_SYS_SICRL SICRL_LDP_A
 350
 351 #define CONFIG_SYS_HID0_INIT    0x000000000
 352 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 353                                  HID0_ENABLE_INSTRUCTION_CACHE)
 354
 355 #define CONFIG_SYS_HID2         HID2_HBE
 356
 357 #define CONFIG_SYS_GPIO1_PRELIM
 358 #define CONFIG_SYS_GPIO1_DIR    0x00100000
 359 #define CONFIG_SYS_GPIO1_DAT    0x00100000
 360
 361 #define CONFIG_SYS_GPIO2_PRELIM
 362 #define CONFIG_SYS_GPIO2_DIR    0x78900000
 363 #define CONFIG_SYS_GPIO2_DAT    0x70100000
 364
 365 #define CONFIG_HIGH_BATS                /* High BATs supported */
 366
 367 /* DDR @ 0x00000000 */
 368 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 369                                  BATL_MEMCOHERENCE)
 370 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
 371                                  BATU_VS | BATU_VP)
 372
 373 /* PCI @ 0x80000000 */
 374 #ifdef CONFIG_PCI
 375 #define CONFIG_PCI_INDIRECT_BRIDGE
 376 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW | \
 377                                  BATL_MEMCOHERENCE)
 378 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
 379                                  BATU_VS | BATU_VP)
 380 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_RW | \
 381                                  BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 382 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
 383                                  BATU_VS | BATU_VP)
 384 #else
 385 #define CONFIG_SYS_IBAT1L       (0)
 386 #define CONFIG_SYS_IBAT1U       (0)
 387 #define CONFIG_SYS_IBAT2L       (0)
 388 #define CONFIG_SYS_IBAT2U       (0)
 389 #endif
 390
 391 #ifdef CONFIG_MPC83XX_PCI2
 392 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_RW | \
 393                                  BATL_MEMCOHERENCE)
 394 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | \
 395                                  BATU_VS | BATU_VP)
 396 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_RW | \
 397                                  BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 398 #define CONFIG_SYS_IBAT4U       (CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | \
 399                                  BATU_VS | BATU_VP)
 400 #else
 401 #define CONFIG_SYS_IBAT3L       (0)
 402 #define CONFIG_SYS_IBAT3U       (0)
 403 #define CONFIG_SYS_IBAT4L       (0)
 404 #define CONFIG_SYS_IBAT4U       (0)
 405 #endif
 406
 407 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
 408 #define CONFIG_SYS_IBAT5L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 409                                  BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 410 #define CONFIG_SYS_IBAT5U       (CONFIG_SYS_IMMR | BATU_BL_256M | \
 411                                  BATU_VS | BATU_VP)
 412
 413 #define CONFIG_SYS_IBAT6L       (0xF0000000 | BATL_PP_RW | BATL_MEMCOHERENCE)
 414 #define CONFIG_SYS_IBAT6U       (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
 415
 416 #if (CONFIG_SYS_DDR_SIZE == 512)
 417 #define CONFIG_SYS_IBAT7L       (CONFIG_SYS_SDRAM_BASE+0x10000000 | \
 418                                  BATL_PP_RW | BATL_MEMCOHERENCE)
 419 #define CONFIG_SYS_IBAT7U       (CONFIG_SYS_SDRAM_BASE+0x10000000 | \
 420                                  BATU_BL_256M | BATU_VS | BATU_VP)
 421 #else
 422 #define CONFIG_SYS_IBAT7L       (0)
 423 #define CONFIG_SYS_IBAT7U       (0)
 424 #endif
 425
 426 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 427 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 428 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 429 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 430 #define CONFIG_SYS_DBAT2L       CONFIG_SYS_IBAT2L
 431 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 432 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 433 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 434 #define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
 435 #define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U
 436 #define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
 437 #define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U
 438 #define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
 439 #define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
 440 #define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
 441 #define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
 442
 443 #if defined(CONFIG_CMD_KGDB)
 444 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 445 #endif
 446
 447 /*
 448  * Environment Configuration
 449  */
 450 #define CONFIG_ENV_OVERWRITE
 451
 452 #if defined(CONFIG_TSEC_ENET)
 453 #define CONFIG_HAS_ETH0
 454 #define CONFIG_HAS_ETH1
 455 #endif
 456
 457 #define CONFIG_HOSTNAME         "VME8349"
 458 #define CONFIG_ROOTPATH         "/tftpboot/rootfs"
 459 #define CONFIG_BOOTFILE         "uImage"
 460
 461 #define CONFIG_LOADADDR         800000  /* def location for tftp and bootm */
 462
 463 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 464         "netdev=eth0\0"                                                 \
 465         "hostname=vme8349\0"                                            \
 466         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 467                 "nfsroot=${serverip}:${rootpath}\0"                     \
 468         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 469         "addip=setenv bootargs ${bootargs} "                            \
 470                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 471                 ":${hostname}:${netdev}:off panic=1\0"                  \
 472         "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 473         "flash_nfs=run nfsargs addip addtty;"                           \
 474                 "bootm ${kernel_addr}\0"                                \
 475         "flash_self=run ramargs addip addtty;"                          \
 476                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 477         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 478                 "bootm\0"                                               \
 479         "load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0"              \
 480         "update=protect off fff00000 fff3ffff; "                        \
 481                 "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
 482         "upd=run load update\0"                                         \
 483         "fdtaddr=780000\0"                                              \
 484         "fdtfile=vme8349.dtb\0"                                         \
 485         ""
 486
 487 #define CONFIG_NFSBOOTCOMMAND                                           \
 488         "setenv bootargs root=/dev/nfs rw "                             \
 489                 "nfsroot=$serverip:$rootpath "                          \
 490                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 491                                                         "$netdev:off "  \
 492                 "console=$consoledev,$baudrate $othbootargs;"           \
 493         "tftp $loadaddr $bootfile;"                                     \
 494         "tftp $fdtaddr $fdtfile;"                                       \
 495         "bootm $loadaddr - $fdtaddr"
 496
 497 #define CONFIG_RAMBOOTCOMMAND                                           \
 498         "setenv bootargs root=/dev/ram rw "                             \
 499                 "console=$consoledev,$baudrate $othbootargs;"           \
 500         "tftp $ramdiskaddr $ramdiskfile;"                               \
 501         "tftp $loadaddr $bootfile;"                                     \
 502         "tftp $fdtaddr $fdtfile;"                                       \
 503         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 504
 505 #define CONFIG_BOOTCOMMAND      "run flash_self"
 506
 507 #ifndef __ASSEMBLY__
 508 int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
 509                      unsigned char *buffer, int len);
 510 #endif
 511
 512 #endif  /* __CONFIG_H */