include/configs/ac14xx.h

   1 /*
   2  * (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
   3  * (C) Copyright 2010 DAVE Srl <www.dave.eu>
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * ifm AC14xx (MPC5121e based) board configuration file
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 #define CONFIG_AC14XX 1
  16 #define CONFIG_DISPLAY_BOARDINFO
  17
  18 /*
  19  * Memory map for the ifm AC14xx board:
  20  *
  21  * 0x0000_0000-0x0FFF_FFFF      DDR RAM (256 MB)
  22  * 0x3000_0000-0x3001_FFFF      On Chip SRAM (128 KB)
  23  * 0x8000_0000-0x803F_FFFF      IMMR (4 MB)
  24  * 0xE000_0000-0xEFFF_FFFF      several LPB attached hardware (CSx)
  25  * 0xFC00_0000-0xFFFF_FFFF      NOR Boot FLASH (64 MB)
  26  */
  27
  28 /*
  29  * High Level Configuration Options
  30  */
  31 #define CONFIG_E300             1       /* E300 Family */
  32
  33 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  34
  35 #if defined(CONFIG_VIDEO)
  36 #define CONFIG_CFB_CONSOLE
  37 #define CONFIG_VGA_AS_SINGLE_DEVICE
  38 #endif
  39
  40 #define CONFIG_SYS_MPC512X_CLKIN        25000000        /* in Hz */
  41 #define SCFR1_IPS_DIV                   2
  42 #define SCFR1_LPC_DIV                   2
  43 #define SCFR1_NFC_DIV                   2
  44 #define SCFR1_DIU_DIV                   240
  45
  46 #define CONFIG_MISC_INIT_R
  47
  48 #define CONFIG_SYS_IMMR                 0x80000000
  49 #define CONFIG_SYS_DIU_ADDR             (CONFIG_SYS_IMMR + 0x2100)
  50
  51 /* more aggressive 'mtest' over a wider address range */
  52 #define CONFIG_SYS_ALT_MEMTEST
  53 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest region */
  54 #define CONFIG_SYS_MEMTEST_END          0x0FE00000
  55
  56 /*
  57  * DDR Setup - manually set all parameters as there's no SPD etc.
  58  */
  59 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
  60 #define CONFIG_SYS_DDR_BASE             0x00000000
  61 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  62 #define CONFIG_SYS_MAX_RAM_SIZE         0x20000000
  63
  64 /*
  65  * DDR Controller Configuration
  66  *
  67  * SYS_CFG:
  68  *      [31:31] MDDRC Soft Reset:       Diabled
  69  *      [30:30] DRAM CKE pin:           Enabled
  70  *      [29:29] DRAM CLK:               Enabled
  71  *      [28:28] Command Mode:           Enabled (For initialization only)
  72  *      [27:25] DRAM Row Select:        dram_row[15:0] = magenta_address[25:10]
  73  *      [24:21] DRAM Bank Select:       dram_bank[1:0] = magenta_address[11:10]
  74  *      [20:19] Read Test:              DON'T USE
  75  *      [18:18] Self Refresh:           Enabled
  76  *      [17:17] 16bit Mode:             Disabled
  77  *      [16:13] Ready Delay:            2
  78  *      [12:12] Half DQS Delay:         Disabled
  79  *      [11:11] Quarter DQS Delay:      Disabled
  80  *      [10:08] Write Delay:            2
  81  *      [07:07] Early ODT:              Disabled
  82  *      [06:06] On DIE Termination:     Disabled
  83  *      [05:05] FIFO Overflow Clear:    DON'T USE here
  84  *      [04:04] FIFO Underflow Clear:   DON'T USE here
  85  *      [03:03] FIFO Overflow Pending:  DON'T USE here
  86  *      [02:02] FIFO Underlfow Pending: DON'T USE here
  87  *      [01:01] FIFO Overlfow Enabled:  Enabled
  88  *      [00:00] FIFO Underflow Enabled: Enabled
  89  * TIME_CFG0
  90  *      [31:16] DRAM Refresh Time:      0 CSB clocks
  91  *      [15:8]  DRAM Command Time:      0 CSB clocks
  92  *      [07:00] DRAM Precharge Time:    0 CSB clocks
  93  * TIME_CFG1
  94  *      [31:26] DRAM tRFC:
  95  *      [25:21] DRAM tWR1:
  96  *      [20:17] DRAM tWRT1:
  97  *      [16:11] DRAM tDRR:
  98  *      [10:05] DRAM tRC:
  99  *      [04:00] DRAM tRAS:
 100  * TIME_CFG2
 101  *      [31:28] DRAM tRCD:
 102  *      [27:23] DRAM tFAW:
 103  *      [22:19] DRAM tRTW1:
 104  *      [18:15] DRAM tCCD:
 105  *      [14:10] DRAM tRTP:
 106  *      [09:05] DRAM tRP:
 107  *      [04:00] DRAM tRPA
 108  */
 109
 110 /*
 111  * NOTE: although this board uses DDR1 only, the common source brings defaults
 112  * for DDR2 init sequences, that's why we have to keep those here as well
 113  */
 114
 115 /* DDR1 -- 32bit, drive strength (pad configuration) 3 for control and data */
 116 #define CONFIG_SYS_IOCTRL_MUX_DDR       ((0 << 6) | (3 << 3) | (3 << 0))
 117
 118 #define CONFIG_SYS_MDDRC_SYS_CFG (/* 0xEAA09100 */ 0 \
 119                         | (1 << 31)     /* RST_B */ \
 120                         | (1 << 30)     /* CKE */ \
 121                         | (1 << 29)     /* CLK_ON */ \
 122                         | (0 << 28)     /* CMD_MODE */ \
 123                         | (5 << 25)     /* DRAM_ROW_SELECT */ \
 124                         | (5 << 21)     /* DRAM_BANK_SELECT */ \
 125                         | (0 << 18)     /* SELF_REF_EN */ \
 126                         | (0 << 17)     /* 16BIT_MODE */ \
 127                         | (4 << 13)     /* RDLY */ \
 128                         | (1 << 12)     /* HALF_DQS_DLY */ \
 129                         | (0 << 11)     /* QUART_DQS_DLY */ \
 130                         | (1 <<  8)     /* WDLY */ \
 131                         | (0 <<  7)     /* EARLY_ODT */ \
 132                         | (0 <<  6)     /* ON_DIE_TERMINATE */ \
 133                         | (0 <<  5)     /* FIFO_OV_CLEAR */ \
 134                         | (0 <<  4)     /* FIFO_UV_CLEAR */ \
 135                         | (0 <<  1)     /* FIFO_OV_EN */ \
 136                         | (0 <<  0)     /* FIFO_UV_EN */ \
 137                         )
 138
 139 #define CONFIG_SYS_MDDRC_TIME_CFG0      0x04E03124
 140 #define CONFIG_SYS_MDDRC_TIME_CFG1      0x30CA1147
 141 #define CONFIG_SYS_MDDRC_TIME_CFG2      0x32B10864
 142
 143 /* register address only, i.e. template without values */
 144 #define CONFIG_SYS_MICRON_BMODE         0x01000000
 145 #define CONFIG_SYS_MICRON_EMODE         0x01010000
 146 #define CONFIG_SYS_MICRON_EMODE2        0x01020000
 147 #define CONFIG_SYS_MICRON_EMODE3        0x01030000
 148 /*
 149  * values for mode registers (without mode register address)
 150  */
 151 /* CAS 2.5 (6), burst seq (0) and length 4 (2) */
 152 #define CONFIG_SYS_MICRON_BMODE_PARAM   0x00000062
 153 #define CONFIG_SYS_MICRON_BMODE_RSTDLL  0x00000100
 154 /* DLL enable, reduced drive strength */
 155 #define CONFIG_SYS_MICRON_EMODE_PARAM   0x00000002
 156
 157 #define CONFIG_SYS_DDRCMD_NOP           0x01380000
 158 #define CONFIG_SYS_DDRCMD_PCHG_ALL      0x01100400
 159 #define CONFIG_SYS_MICRON_EMR          ((1 << 24) |     /* CMD_REQ */ \
 160                                         (0 << 22) |     /* DRAM_CS */ \
 161                                         (0 << 21) |     /* DRAM_RAS */ \
 162                                         (0 << 20) |     /* DRAM_CAS */ \
 163                                         (0 << 19) |     /* DRAM_WEB */ \
 164                                         (1 << 16) |     /* DRAM_BS[2:0] */ \
 165                                         (0 << 15) |     /* */ \
 166                                         (0 << 12) |     /* A12->out */ \
 167                                         (0 << 11) |     /* A11->RDQS */ \
 168                                         (0 << 10) |     /* A10->DQS# */ \
 169                                         (0 <<  7) |     /* OCD program */ \
 170                                         (0 <<  6) |     /* Rtt1 */ \
 171                                         (0 <<  3) |     /* posted CAS# */ \
 172                                         (0 <<  2) |     /* Rtt0 */ \
 173                                         (1 <<  1) |     /* ODS */ \
 174                                         (0 <<  0)       /* DLL */ \
 175                                      )
 176 #define CONFIG_SYS_MICRON_EMR2          0x01020000
 177 #define CONFIG_SYS_MICRON_EMR3          0x01030000
 178 #define CONFIG_SYS_DDRCMD_RFSH          0x01080000
 179 #define CONFIG_SYS_MICRON_INIT_DEV_OP   0x01000432
 180 #define CONFIG_SYS_MICRON_EMR_OCD      ((1 << 24) |     /* CMD_REQ */ \
 181                                         (0 << 22) |     /* DRAM_CS */ \
 182                                         (0 << 21) |     /* DRAM_RAS */ \
 183                                         (0 << 20) |     /* DRAM_CAS */ \
 184                                         (0 << 19) |     /* DRAM_WEB */ \
 185                                         (1 << 16) |     /* DRAM_BS[2:0] */ \
 186                                         (0 << 15) |     /* */ \
 187                                         (0 << 12) |     /* A12->out */ \
 188                                         (0 << 11) |     /* A11->RDQS */ \
 189                                         (1 << 10) |     /* A10->DQS# */ \
 190                                         (7 <<  7) |     /* OCD program */ \
 191                                         (0 <<  6) |     /* Rtt1 */ \
 192                                         (0 <<  3) |     /* posted CAS# */ \
 193                                         (1 <<  2) |     /* Rtt0 */ \
 194                                         (0 <<  1) |     /* ODS */ \
 195                                         (0 <<  0)       /* DLL */ \
 196                                      )
 197
 198 /*
 199  * Backward compatible definitions,
 200  * so we do not have to change arch/powerpc/cpu/mpc512x/fixed_sdram.c
 201  */
 202 #define CONFIG_SYS_DDRCMD_EM2           (CONFIG_SYS_MICRON_EMR2)
 203 #define CONFIG_SYS_DDRCMD_EM3           (CONFIG_SYS_MICRON_EMR3)
 204 #define CONFIG_SYS_DDRCMD_EN_DLL        (CONFIG_SYS_MICRON_EMR)
 205 #define CONFIG_SYS_DDRCMD_OCD_DEFAULT   (CONFIG_SYS_MICRON_EMR_OCD)
 206
 207 /* DDR Priority Manager Configuration */
 208 #define CONFIG_SYS_MDDRCGRP_PM_CFG1     0x00077777
 209 #define CONFIG_SYS_MDDRCGRP_PM_CFG2     0x00000000
 210 #define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG  0x00000001
 211 #define CONFIG_SYS_MDDRCGRP_LUT0_MU     0xFFEEDDCC
 212 #define CONFIG_SYS_MDDRCGRP_LUT0_ML     0xBBAAAAAA
 213 #define CONFIG_SYS_MDDRCGRP_LUT1_MU     0x66666666
 214 #define CONFIG_SYS_MDDRCGRP_LUT1_ML     0x55555555
 215 #define CONFIG_SYS_MDDRCGRP_LUT2_MU     0x44444444
 216 #define CONFIG_SYS_MDDRCGRP_LUT2_ML     0x44444444
 217 #define CONFIG_SYS_MDDRCGRP_LUT3_MU     0x55555555
 218 #define CONFIG_SYS_MDDRCGRP_LUT3_ML     0x55555558
 219 #define CONFIG_SYS_MDDRCGRP_LUT4_MU     0x11111111
 220 #define CONFIG_SYS_MDDRCGRP_LUT4_ML     0x11111122
 221 #define CONFIG_SYS_MDDRCGRP_LUT0_AU     0xaaaaaaaa
 222 #define CONFIG_SYS_MDDRCGRP_LUT0_AL     0xaaaaaaaa
 223 #define CONFIG_SYS_MDDRCGRP_LUT1_AU     0x66666666
 224 #define CONFIG_SYS_MDDRCGRP_LUT1_AL     0x66666666
 225 #define CONFIG_SYS_MDDRCGRP_LUT2_AU     0x11111111
 226 #define CONFIG_SYS_MDDRCGRP_LUT2_AL     0x11111111
 227 #define CONFIG_SYS_MDDRCGRP_LUT3_AU     0x11111111
 228 #define CONFIG_SYS_MDDRCGRP_LUT3_AL     0x11111111
 229 #define CONFIG_SYS_MDDRCGRP_LUT4_AU     0x11111111
 230 #define CONFIG_SYS_MDDRCGRP_LUT4_AL     0x11111111
 231
 232 /*
 233  * NOR FLASH on the Local Bus
 234  */
 235 #define CONFIG_SYS_FLASH_CFI                            /* use the CFI code */
 236 #define CONFIG_FLASH_CFI_DRIVER                         /* use the CFI driver */
 237 #define CONFIG_SYS_FLASH_BASE           0xFC000000      /* start of FLASH */
 238 #define CONFIG_SYS_FLASH_SIZE           0x04000000      /* max flash size */
 239
 240 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 241 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 242 #define CONFIG_SYS_FLASH_BANKS_LIST     { \
 243         CONFIG_SYS_FLASH_BASE + 0 * CONFIG_SYS_FLASH_SIZE, \
 244         }
 245 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* max sectors per device */
 246
 247 #undef CONFIG_SYS_FLASH_CHECKSUM
 248 #define CONFIG_SYS_FLASH_PROTECTION
 249
 250 /*
 251  * SRAM support
 252  */
 253 #define CONFIG_SYS_SRAM_BASE            0x30000000
 254 #define CONFIG_SYS_SRAM_SIZE            0x00020000      /* 128 KB */
 255
 256 /*
 257  * CS related parameters
 258  */
 259 /* CS0 Flash */
 260 #define CONFIG_SYS_CS0_CFG              0x00031110
 261 #define CONFIG_SYS_CS0_START            0xFC000000
 262 #define CONFIG_SYS_CS0_SIZE             0x04000000
 263 /* CS1 FRAM */
 264 #define CONFIG_SYS_CS1_CFG              0x00011000
 265 #define CONFIG_SYS_CS1_START            0xE0000000
 266 #define CONFIG_SYS_CS1_SIZE             0x00010000
 267 /* CS2 AS-i 1 */
 268 #define CONFIG_SYS_CS2_CFG              0x00009100
 269 #define CONFIG_SYS_CS2_START            0xE0100000
 270 #define CONFIG_SYS_CS2_SIZE             0x00080000
 271 /* CS3 netX */
 272 #define CONFIG_SYS_CS3_CFG              0x000A1140
 273 #define CONFIG_SYS_CS3_START            0xE0300000
 274 #define CONFIG_SYS_CS3_SIZE             0x00020000
 275 /* CS5 safety */
 276 #define CONFIG_SYS_CS5_CFG              0x0011F000
 277 #define CONFIG_SYS_CS5_START            0xE0400000
 278 #define CONFIG_SYS_CS5_SIZE             0x00010000
 279 /* CS6 AS-i 2 */
 280 #define CONFIG_SYS_CS6_CFG              0x00009100
 281 #define CONFIG_SYS_CS6_START            0xE0200000
 282 #define CONFIG_SYS_CS6_SIZE             0x00080000
 283
 284 /* Don't use alternative CS timing for any CS */
 285 #define CONFIG_SYS_CS_ALETIMING         0x00000000
 286 #define CONFIG_SYS_CS_BURST             0x00000000
 287 #define CONFIG_SYS_CS_DEADCYCLE         0x00000020
 288 #define CONFIG_SYS_CS_HOLDCYCLE         0x00000020
 289
 290 /* Use SRAM for initial stack */
 291 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_SRAM_BASE
 292 #define CONFIG_SYS_INIT_RAM_SIZE        CONFIG_SYS_SRAM_SIZE
 293
 294 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 295                                          GENERATED_GBL_DATA_SIZE)
 296 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 297
 298 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 299 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)
 300
 301 #ifdef  CONFIG_FSL_DIU_FB
 302 #define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024)
 303 #else
 304 #define CONFIG_SYS_MALLOC_LEN           (512 * 1024)
 305 #endif
 306
 307 /*
 308  * Serial Port
 309  */
 310 #define CONFIG_CONS_INDEX               1
 311
 312 /*
 313  * Serial console configuration
 314  */
 315 #define CONFIG_PSC_CONSOLE              3       /* console on PSC3 */
 316 #define CONFIG_SYS_PSC3
 317 #if CONFIG_PSC_CONSOLE != 3
 318 #error CONFIG_PSC_CONSOLE must be 3
 319 #endif
 320
 321 #define CONFIG_BAUDRATE                 115200  /* ... at 115200 bps */
 322
 323 #define CONSOLE_FIFO_TX_SIZE            FIFOC_PSC3_TX_SIZE
 324 #define CONSOLE_FIFO_TX_ADDR            FIFOC_PSC3_TX_ADDR
 325 #define CONSOLE_FIFO_RX_SIZE            FIFOC_PSC3_RX_SIZE
 326 #define CONSOLE_FIFO_RX_ADDR            FIFOC_PSC3_RX_ADDR
 327
 328 /*
 329  * Clocks in use
 330  */
 331 #define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN |           \
 332                          CLOCK_SCCR1_LPC_EN |           \
 333                          CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \
 334                          CLOCK_SCCR1_PSC_EN(7) |        \
 335                          CLOCK_SCCR1_PSCFIFO_EN |       \
 336                          CLOCK_SCCR1_DDR_EN |           \
 337                          CLOCK_SCCR1_FEC_EN |           \
 338                          CLOCK_SCCR1_TPR_EN)
 339
 340 #define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN |           \
 341                          CLOCK_SCCR2_SPDIF_EN |         \
 342                          CLOCK_SCCR2_DIU_EN |           \
 343                          CLOCK_SCCR2_I2C_EN)
 344
 345 #define CONFIG_CMDLINE_EDITING          1       /* command line history */
 346
 347 /* I2C */
 348 #define CONFIG_HARD_I2C                 /* I2C with hardware support */
 349 #define CONFIG_I2C_MULTI_BUS
 350
 351 /* I2C speed and slave address */
 352 #define CONFIG_SYS_I2C_SPEED            100000
 353 #define CONFIG_SYS_I2C_SLAVE            0x7F
 354
 355 /*
 356  * IIM - IC Identification Module
 357  */
 358 #undef CONFIG_FSL_IIM
 359
 360 /*
 361  * EEPROM configuration for Atmel AT24C01:
 362  * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode
 363  */
 364 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 365 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x52
 366 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   30
 367 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       5
 368
 369 /*
 370  * Ethernet configuration
 371  */
 372 #define CONFIG_MPC512x_FEC              1
 373 #define CONFIG_PHY_ADDR                 0x1F
 374 #define CONFIG_MII                      1       /* MII PHY management */
 375 #define CONFIG_FEC_AN_TIMEOUT           1
 376 #define CONFIG_HAS_ETH0
 377
 378 /*
 379  * Environment
 380  */
 381 #define CONFIG_ENV_IS_IN_FLASH          1
 382 /* This has to be a multiple of the flash sector size */
 383 #define CONFIG_ENV_ADDR                 0xFFF40000
 384 #define CONFIG_ENV_SIZE                 0x2000
 385 #define CONFIG_ENV_SECT_SIZE            0x20000
 386
 387 /* Address and size of Redundant Environment Sector */
 388 #define CONFIG_ENV_ADDR_REDUND          (CONFIG_ENV_ADDR + \
 389                                          CONFIG_ENV_SECT_SIZE)
 390 #define CONFIG_ENV_SIZE_REDUND          (CONFIG_ENV_SIZE)
 391
 392 #define CONFIG_LOADS_ECHO               1
 393 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1
 394
 395 #define CONFIG_CMD_EEPROM
 396 #undef CONFIG_CMD_FUSE
 397 #undef CONFIG_CMD_IDE
 398 #define CONFIG_CMD_JFFS2
 399 #define CONFIG_CMD_REGINFO
 400
 401 #if defined(CONFIG_PCI)
 402 #define CONFIG_CMD_PCI
 403 #endif
 404
 405 #if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2)
 406 #define CONFIG_DOS_PARTITION
 407 #define CONFIG_MAC_PARTITION
 408 #define CONFIG_ISO_PARTITION
 409 #endif /* defined(CONFIG_CMD_IDE) */
 410
 411 /*
 412  * Miscellaneous configurable options
 413  */
 414 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 415 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 416
 417 #ifdef CONFIG_CMD_KGDB
 418 # define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
 419 #else
 420 # define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
 421 #endif
 422
 423 /* Print Buffer Size */
 424 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
 425                                  sizeof(CONFIG_SYS_PROMPT) + 16)
 426 /* max number of command args */
 427 #define CONFIG_SYS_MAXARGS      32
 428 /* Boot Argument Buffer Size */
 429 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 430
 431 /*
 432  * For booting Linux, the board info and command line data
 433  * have to be in the first 8 MB of memory, since this is
 434  * the maximum mapped by the Linux kernel during initialization.
 435  */
 436 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)
 437
 438 /* Cache Configuration */
 439 #define CONFIG_SYS_DCACHE_SIZE          32768
 440 #define CONFIG_SYS_CACHELINE_SIZE       32
 441 #ifdef CONFIG_CMD_KGDB
 442 #define CONFIG_SYS_CACHELINE_SHIFT      5       /* log base 2 of 32 */
 443 #endif
 444
 445 #define CONFIG_SYS_HID0_INIT            0x000000000
 446 #define CONFIG_SYS_HID0_FINAL           (HID0_ENABLE_MACHINE_CHECK | \
 447                                          HID0_ICE)
 448 #define CONFIG_SYS_HID2 HID2_HBE
 449
 450 #define CONFIG_HIGH_BATS                1       /* High BATs supported */
 451
 452 /*
 453  * Internal Definitions
 454  *
 455  * Boot Flags
 456  */
 457 #define BOOTFLAG_COLD                   0x01
 458 #define BOOTFLAG_WARM                   0x02
 459
 460 #ifdef CONFIG_CMD_KGDB
 461 #define CONFIG_KGDB_BAUDRATE            230400  /* speed of kgdb serial port */
 462 #endif
 463
 464 /*
 465  * Environment Configuration
 466  */
 467 #define CONFIG_ENV_OVERWRITE
 468 #define CONFIG_TIMESTAMP
 469
 470 /* default load addr for tftp and bootm */
 471 #define CONFIG_LOADADDR         400000
 472
 473 #define CONFIG_BOOTDELAY        2       /* -1 disables auto-boot */
 474
 475 /* the builtin environment and standard greeting */
 476 #define CONFIG_PREBOOT  "echo;" \
 477         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 478         "echo"
 479
 480 #define CONFIG_EXTRA_ENV_SETTINGS_DEVEL                                 \
 481         "muster_nr=-00\0"                                               \
 482         "fromram=run ramargs addip addtty; "                            \
 483                 "tftp ${fdt_addr_r} ac14xx/ac14xx.dtb${muster_nr}; "    \
 484                 "tftp ${kernel_addr_r} ac14xx/uImage${muster_nr}; "     \
 485                 "tftp ${ramdisk_addr_r} ac14xx/uFS${muster_nr}; "       \
 486                 "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0" \
 487         "fromnfs=run nfsargs addip addtty; "                            \
 488                 "tftp ${fdt_addr_r} ac14xx/ac14xx.dtb${muster_nr}; "    \
 489                 "tftp ${kernel_addr_r} ac14xx/uImage${muster_nr}; "     \
 490                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 491         "fromflash=run nfsargs addip addtty; "                          \
 492                 "bootm fc020000 - fc000000\0"                           \
 493         "mtdargsrec=setenv bootargs root=/dev/mtdblock1 ro\0"           \
 494         "recovery=run mtdargsrec addip addtty; "                        \
 495                 "bootm ffd20000 - ffee0000\0"                           \
 496         "production=run ramargs addip addtty; "                         \
 497                 "bootm fc020000 fc400000 fc000000\0"                    \
 498         "mtdargs=setenv bootargs root=/dev/mtdblock1 ro\0"              \
 499         "prodmtd=run mtdargs addip addtty; "                            \
 500                 "bootm fc020000 - fc000000\0"                           \
 501         ""
 502
 503 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 504         "u-boot_addr_r=200000\0"                                        \
 505         "kernel_addr_r=600000\0"                                        \
 506         "fdt_addr_r=a00000\0"                                           \
 507         "ramdisk_addr_r=b00000\0"                                       \
 508         "u-boot_addr=FFF00000\0"                                        \
 509         "kernel_addr=FC020000\0"                                        \
 510         "fdt_addr=FC000000\0"                                           \
 511         "ramdisk_addr=FC400000\0"                                       \
 512         "verify=n\0"                                                    \
 513         "ramdiskfile=ac14xx/uRamdisk\0"                                 \
 514         "u-boot=ac14xx/u-boot.bin\0"                                    \
 515         "bootfile=ac14xx/uImage\0"                                      \
 516         "fdtfile=ac14xx/ac14xx.dtb\0"                                   \
 517         "netdev=eth0\0"                                                 \
 518         "consdev=ttyPSC0\0"                                             \
 519         "hostname=ac14xx\0"                                             \
 520         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 521                 "nfsroot=${serverip}:${rootpath}${muster_nr}\0" \
 522         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 523         "addip=setenv bootargs ${bootargs} "                            \
 524                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 525                 ":${hostname}:${netdev}:off panic=1\0"                  \
 526         "addtty=setenv bootargs ${bootargs} "                           \
 527                 "console=${consdev},${baudrate}\0"                      \
 528         "flash_nfs=run nfsargs addip addtty;"                           \
 529                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 530         "flash_self=run ramargs addip addtty;"                          \
 531                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 532         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 533                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 534                 "run nfsargs addip addtty;"                             \
 535                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 536         "net_self=tftp ${kernel_addr_r} ${bootfile};"                   \
 537                 "tftp ${ramdisk_addr_r} ${ramdiskfile};"                \
 538                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 539                 "run ramargs addip addtty;"                             \
 540                 "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
 541         "load=tftp ${u-boot_addr_r} ${u-boot}\0"                        \
 542         "update=protect off ${u-boot_addr} +${filesize};"               \
 543                 "era ${u-boot_addr} +${filesize};"                      \
 544                 "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0"    \
 545         CONFIG_EXTRA_ENV_SETTINGS_DEVEL                                 \
 546         "upd=run load update\0"                                         \
 547         ""
 548
 549 #define CONFIG_BOOTCOMMAND      "run production"
 550
 551 #define CONFIG_ARP_TIMEOUT      200UL
 552
 553 #define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES      1
 554
 555 #define OF_CPU                  "PowerPC,5121@0"
 556 #define OF_SOC_COMPAT           "fsl,mpc5121-immr"
 557 #define OF_TBCLK                (bd->bi_busfreq / 4)
 558 #define OF_STDOUT_PATH          "/soc@80000000/serial@11300"
 559
 560 #endif  /* __CONFIG_H */