include/configs/UCP1020.h

   1 /*
   2  * Copyright 2013-2015 Arcturus Networks, Inc.
   3  *           http://www.arcturusnetworks.com/products/ucp1020/
   4  * based on include/configs/p1_p2_rdb_pc.h
   5  * original copyright follows:
   6  * Copyright 2009-2011 Freescale Semiconductor, Inc.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 /*
  12  * QorIQ uCP1020-xx boards configuration file
  13  */
  14 #ifndef __CONFIG_H
  15 #define __CONFIG_H
  16
  17 #define CONFIG_SYS_GENERIC_BOARD
  18 #define CONFIG_DISPLAY_BOARDINFO
  19
  20 #define CONFIG_FSL_ELBC
  21 #define CONFIG_PCI
  22 #define CONFIG_PCIE1    /* PCIE controller 1 (slot 1) */
  23 #define CONFIG_PCIE2    /* PCIE controller 2 (slot 2) */
  24 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
  25 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
  26 #define CONFIG_FSL_PCIE_RESET   /* need PCIe reset errata */
  27 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
  28
  29 #if defined(CONFIG_TARTGET_UCP1020T1)
  30
  31 #define CONFIG_UCP1020_REV_1_3
  32
  33 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
  34 #define CONFIG_P1020
  35
  36 #define CONFIG_TSEC_ENET
  37 #define CONFIG_TSEC1
  38 #define CONFIG_TSEC3
  39 #define CONFIG_HAS_ETH0
  40 #define CONFIG_HAS_ETH1
  41 #define CONFIG_ETHADDR          00:19:D3:FF:FF:FF
  42 #define CONFIG_ETH1ADDR         00:19:D3:FF:FF:FE
  43 #define CONFIG_ETH2ADDR         00:19:D3:FF:FF:FD
  44 #define CONFIG_IPADDR           10.80.41.229
  45 #define CONFIG_SERVERIP         10.80.41.227
  46 #define CONFIG_NETMASK          255.255.252.0
  47 #define CONFIG_ETHPRIME         "eTSEC3"
  48
  49 #ifndef CONFIG_SPI_FLASH
  50 #endif
  51 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  52
  53 #define CONFIG_MMC
  54 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  55
  56 #define CONFIG_LAST_STAGE_INIT
  57
  58 #if !defined(CONFIG_DONGLE)
  59 #define CONFIG_SILENT_CONSOLE
  60 #endif
  61
  62 #endif
  63
  64 #if defined(CONFIG_TARGET_UCP1020)
  65
  66 #define CONFIG_UCP1020
  67 #define CONFIG_UCP1020_REV_1_3
  68
  69 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
  70 #define CONFIG_P1020
  71
  72 #define CONFIG_TSEC_ENET
  73 #define CONFIG_TSEC1
  74 #define CONFIG_TSEC2
  75 #define CONFIG_TSEC3
  76 #define CONFIG_HAS_ETH0
  77 #define CONFIG_HAS_ETH1
  78 #define CONFIG_HAS_ETH2
  79 #define CONFIG_ETHADDR          00:06:3B:FF:FF:FF
  80 #define CONFIG_ETH1ADDR         00:06:3B:FF:FF:FE
  81 #define CONFIG_ETH2ADDR         00:06:3B:FF:FF:FD
  82 #define CONFIG_IPADDR           192.168.1.81
  83 #define CONFIG_IPADDR1          192.168.1.82
  84 #define CONFIG_IPADDR2          192.168.1.83
  85 #define CONFIG_SERVERIP         192.168.1.80
  86 #define CONFIG_GATEWAYIP        102.168.1.1
  87 #define CONFIG_NETMASK          255.255.255.0
  88 #define CONFIG_ETHPRIME         "eTSEC1"
  89
  90 #ifndef CONFIG_SPI_FLASH
  91 #endif
  92 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  93
  94 #define CONFIG_MMC
  95 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  96
  97 #define CONFIG_LAST_STAGE_INIT
  98
  99 #endif
 100
 101 #ifdef CONFIG_SDCARD
 102 #define CONFIG_RAMBOOT_SDCARD
 103 #define CONFIG_SYS_RAMBOOT
 104 #define CONFIG_SYS_EXTRA_ENV_RELOC
 105 #define CONFIG_SYS_TEXT_BASE            0x11000000
 106 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
 107 #endif
 108
 109 #ifdef CONFIG_SPIFLASH
 110 #define CONFIG_RAMBOOT_SPIFLASH
 111 #define CONFIG_SYS_RAMBOOT
 112 #define CONFIG_SYS_EXTRA_ENV_RELOC
 113 #define CONFIG_SYS_TEXT_BASE            0x11000000
 114 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
 115 #endif
 116
 117 #ifndef CONFIG_SYS_TEXT_BASE
 118 #define CONFIG_SYS_TEXT_BASE            0xeff80000
 119 #endif
 120 #define CONFIG_SYS_TEXT_BASE_NOR        0xeff80000
 121
 122 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 123 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 124 #endif
 125
 126 #ifndef CONFIG_SYS_MONITOR_BASE
 127 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 128 #endif
 129
 130 /* High Level Configuration Options */
 131 #define CONFIG_BOOKE
 132 #define CONFIG_E500
 133 /* #define CONFIG_MPC85xx */
 134
 135 #define CONFIG_MP
 136
 137 #define CONFIG_FSL_LAW
 138
 139 #define CONFIG_ENV_OVERWRITE
 140
 141 #define CONFIG_CMD_SATA
 142 #define CONFIG_SATA_SIL
 143 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 144 #define CONFIG_LIBATA
 145 #define CONFIG_LBA48
 146
 147 #define CONFIG_SYS_CLK_FREQ     66666666
 148 #define CONFIG_DDR_CLK_FREQ     66666666
 149
 150 #define CONFIG_HWCONFIG
 151
 152 #define CONFIG_DTT_ADM1021      1       /* ADM1021 temp sensor support  */
 153 #define CONFIG_SYS_DTT_BUS_NUM  1       /* The I2C bus for DTT          */
 154 #define CONFIG_DTT_SENSORS      { 0, 1 }        /* Sensor index */
 155 /*
 156  * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
 157  * there will be one entry in this array for each two (dummy) sensors in
 158  * CONFIG_DTT_SENSORS.
 159  *
 160  * For uCP1020 module:
 161  * - only one ADM1021/NCT72
 162  * - i2c addr 0x41
 163  * - conversion rate 0x02 = 0.25 conversions/second
 164  * - ALERT output disabled
 165  * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
 166  * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
 167  */
 168 #define CONFIG_SYS_DTT_ADM1021  { { CONFIG_SYS_I2C_NCT72_ADDR, \
 169                                          0x02, 0, 1, 0, 85, 1, 0, 85} }
 170
 171 #define CONFIG_CMD_DTT
 172
 173 /*
 174  * These can be toggled for performance analysis, otherwise use default.
 175  */
 176 #define CONFIG_L2_CACHE
 177 #define CONFIG_BTB
 178
 179 #define CONFIG_BOARD_EARLY_INIT_F       /* Call board_pre_init */
 180
 181 #define CONFIG_ENABLE_36BIT_PHYS
 182
 183 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 184 #define CONFIG_SYS_MEMTEST_END          0x1fffffff
 185 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
 186
 187 #define CONFIG_SYS_CCSRBAR              0xffe00000
 188 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
 189
 190 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
 191        SPL code*/
 192 #ifdef CONFIG_SPL_BUILD
 193 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 194 #endif
 195
 196 /* DDR Setup */
 197 #define CONFIG_DDR_ECC_ENABLE
 198 #define CONFIG_SYS_FSL_DDR3
 199 #ifndef CONFIG_DDR_ECC_ENABLE
 200 #define CONFIG_SYS_DDR_RAW_TIMING
 201 #define CONFIG_DDR_SPD
 202 #endif
 203 #define CONFIG_SYS_SPD_BUS_NUM 1
 204 #undef CONFIG_FSL_DDR_INTERACTIVE
 205
 206 #define CONFIG_SYS_SDRAM_SIZE_LAW       LAW_SIZE_512M
 207 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
 208 #define CONFIG_SYS_SDRAM_SIZE           (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
 209 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 210 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 211
 212 #define CONFIG_NUM_DDR_CONTROLLERS      1
 213 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 214
 215 /* Default settings for DDR3 */
 216 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
 217 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
 218 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
 219 #define CONFIG_SYS_DDR_CS1_BNDS         0x0040007f
 220 #define CONFIG_SYS_DDR_CS1_CONFIG       0x80014302
 221 #define CONFIG_SYS_DDR_CS1_CONFIG_2     0x00000000
 222
 223 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 224 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
 225 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
 226 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
 227
 228 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
 229 #define CONFIG_SYS_DDR_WRLVL_CONTROL    0x8655A608
 230 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
 231 #define CONFIG_SYS_DDR_RCW_1            0x00000000
 232 #define CONFIG_SYS_DDR_RCW_2            0x00000000
 233 #ifdef CONFIG_DDR_ECC_ENABLE
 234 #define CONFIG_SYS_DDR_CONTROL          0xE70C0000      /* Type = DDR3 & ECC */
 235 #else
 236 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3 */
 237 #endif
 238 #define CONFIG_SYS_DDR_CONTROL_2        0x04401050
 239 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 240 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 241
 242 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 243 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
 244 #define CONFIG_SYS_DDR_TIMING_1         0x6f6B4846
 245 #define CONFIG_SYS_DDR_TIMING_2         0x0FA8C8CF
 246 #define CONFIG_SYS_DDR_CLK_CTRL         0x03000000
 247 #define CONFIG_SYS_DDR_MODE_1           0x40461520
 248 #define CONFIG_SYS_DDR_MODE_2           0x8000c000
 249 #define CONFIG_SYS_DDR_INTERVAL         0x0C300000
 250
 251 #undef CONFIG_CLOCKS_IN_MHZ
 252
 253 /*
 254  * Memory map
 255  *
 256  * 0x0000_0000 0x7fff_ffff      DDR             Up to 2GB cacheable
 257  * 0x8000_0000 0xdfff_ffff      PCI Express Mem 1G non-cacheable(PCIe * 2)
 258  * 0xec00_0000 0xefff_ffff      NOR flash       Up to 64M non-cacheable CS0/1
 259  * 0xf8f8_0000 0xf8ff_ffff      L2 SRAM         Up to 256K cacheable
 260  *   (early boot only)
 261  * 0xffc0_0000 0xffc3_ffff      PCI IO range    256k non-cacheable
 262  * 0xffd0_0000 0xffd0_3fff      L1 for stack    16K cacheable
 263  * 0xffe0_0000 0xffef_ffff      CCSR            1M non-cacheable
 264  */
 265
 266 /*
 267  * Local Bus Definitions
 268  */
 269 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* 64M */
 270 #define CONFIG_SYS_FLASH_BASE           0xec000000
 271
 272 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 273
 274 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 275         | BR_PS_16 | BR_V)
 276
 277 #define CONFIG_FLASH_OR_PRELIM          0xfc000ff7
 278
 279 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
 280 #define CONFIG_SYS_FLASH_QUIET_TEST
 281 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 282
 283 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 284
 285 #undef CONFIG_SYS_FLASH_CHECKSUM
 286 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 287 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 288
 289 #define CONFIG_FLASH_CFI_DRIVER
 290 #define CONFIG_SYS_FLASH_CFI
 291 #define CONFIG_SYS_FLASH_EMPTY_INFO
 292 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 293
 294 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 295
 296 #define CONFIG_SYS_INIT_RAM_LOCK
 297 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000 /* stack in RAM */
 298 /* Initial L1 address */
 299 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 300 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 301 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 302 /* Size of used area in RAM */
 303 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 304
 305 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 306                                         GENERATED_GBL_DATA_SIZE)
 307 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 308
 309 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)/* Reserve 256 kB for Mon */
 310 #define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)/* Reserved for malloc */
 311
 312 #define CONFIG_SYS_PMC_BASE     0xff980000
 313 #define CONFIG_SYS_PMC_BASE_PHYS        CONFIG_SYS_PMC_BASE
 314 #define CONFIG_PMC_BR_PRELIM    (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
 315                                         BR_PS_8 | BR_V)
 316 #define CONFIG_PMC_OR_PRELIM    (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
 317                                  OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
 318                                  OR_GPCM_EAD)
 319
 320 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 321 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 322 #ifdef CONFIG_NAND_FSL_ELBC
 323 #define CONFIG_SYS_BR1_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
 324 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 325 #endif
 326
 327 /* Serial Port - controlled on board with jumper J8
 328  * open - index 2
 329  * shorted - index 1
 330  */
 331 #define CONFIG_CONS_INDEX               1
 332 #undef CONFIG_SERIAL_SOFTWARE_FIFO
 333 #define CONFIG_SYS_NS16550
 334 #define CONFIG_SYS_NS16550_SERIAL
 335 #define CONFIG_SYS_NS16550_REG_SIZE     1
 336 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 337 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
 338 #define CONFIG_NS16550_MIN_FUNCTIONS
 339 #endif
 340
 341 #define CONFIG_SYS_BAUDRATE_TABLE       \
 342         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 343
 344 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
 345 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
 346
 347 /* Use the HUSH parser */
 348 #define CONFIG_SYS_HUSH_PARSER
 349
 350 /*
 351  * Pass open firmware flat tree
 352  */
 353 #define CONFIG_OF_LIBFDT
 354 #define CONFIG_OF_BOARD_SETUP
 355 #define CONFIG_OF_STDOUT_VIA_ALIAS
 356
 357 /* new uImage format support */
 358 #define CONFIG_FIT
 359 #define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */
 360
 361 /* I2C */
 362 #define CONFIG_SYS_I2C
 363 #define CONFIG_SYS_I2C_FSL
 364 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 365 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 366 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 367 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 368 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 369 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 370 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x29} }
 371 #define CONFIG_SYS_SPD_BUS_NUM          1 /* For rom_loc and flash bank */
 372
 373 #define CONFIG_RTC_DS1337
 374 #define CONFIG_SYS_RTC_DS1337_NOOSC
 375 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 376 #define CONFIG_SYS_I2C_PCA9557_ADDR     0x18
 377 #define CONFIG_SYS_I2C_NCT72_ADDR       0x4C
 378 #define CONFIG_SYS_I2C_IDT6V49205B      0x69
 379
 380 /*
 381  * eSPI - Enhanced SPI
 382  */
 383 #define CONFIG_HARD_SPI
 384 #define CONFIG_FSL_ESPI
 385
 386 #define CONFIG_SPI_FLASH_SST            1
 387 #define CONFIG_SPI_FLASH_STMICRO        1
 388 #define CONFIG_SPI_FLASH_WINBOND        1
 389 #define CONFIG_CMD_SF                   1
 390 #define CONFIG_CMD_SPI                  1
 391 #define CONFIG_SF_DEFAULT_SPEED         10000000
 392 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 393
 394 #if defined(CONFIG_PCI)
 395 /*
 396  * General PCI
 397  * Memory space is mapped 1-1, but I/O space must start from 0.
 398  */
 399
 400 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 401 #define CONFIG_SYS_PCIE2_NAME           "PCIe SLOT CON9"
 402 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 403 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 404 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 405 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 406 #define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
 407 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 408 #define CONFIG_SYS_PCIE2_IO_PHYS        0xffc10000
 409 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 410
 411 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 412 #define CONFIG_SYS_PCIE1_NAME           "PCIe SLOT CON10"
 413 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 414 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 415 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 416 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 417 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 418 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 419 #define CONFIG_SYS_PCIE1_IO_PHYS        0xffc00000
 420 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 421
 422 #define CONFIG_PCI_PNP  /* do pci plug-and-play */
 423 #define CONFIG_CMD_PCI
 424
 425 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 426 #define CONFIG_DOS_PARTITION
 427 #endif /* CONFIG_PCI */
 428
 429 /*
 430  * Environment
 431  */
 432 #ifdef CONFIG_ENV_FIT_UCBOOT
 433
 434 #define CONFIG_ENV_IS_IN_FLASH
 435 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x20000)
 436 #define CONFIG_ENV_SIZE         0x20000
 437 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 438
 439 #else
 440
 441 #define CONFIG_ENV_SPI_BUS      0
 442 #define CONFIG_ENV_SPI_CS       0
 443 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 444 #define CONFIG_ENV_SPI_MODE     0
 445
 446 #ifdef CONFIG_RAMBOOT_SPIFLASH
 447
 448 #define CONFIG_ENV_IS_IN_SPI_FLASH
 449 #define CONFIG_ENV_SIZE         0x3000          /* 12KB */
 450 #define CONFIG_ENV_OFFSET       0x2000          /* 8KB */
 451 #define CONFIG_ENV_SECT_SIZE    0x1000
 452
 453 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 454 /* Address and size of Redundant Environment Sector     */
 455 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 456 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 457 #endif
 458
 459 #elif defined(CONFIG_RAMBOOT_SDCARD)
 460 #define CONFIG_ENV_IS_IN_MMC
 461 #define CONFIG_FSL_FIXED_MMC_LOCATION
 462 #define CONFIG_ENV_SIZE         0x2000
 463 #define CONFIG_SYS_MMC_ENV_DEV  0
 464
 465 #elif defined(CONFIG_SYS_RAMBOOT)
 466 #define CONFIG_ENV_IS_NOWHERE   /* Store ENV in memory only */
 467 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 468 #define CONFIG_ENV_SIZE         0x2000
 469
 470 #else
 471 #define CONFIG_ENV_IS_IN_FLASH
 472 #define CONFIG_ENV_BASE         (CONFIG_SYS_FLASH_BASE)
 473 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 474 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 475 #define CONFIG_ENV_ADDR         (CONFIG_ENV_BASE + 0xC0000)
 476 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 477 /* Address and size of Redundant Environment Sector     */
 478 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
 479 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 480 #endif
 481
 482 #endif
 483
 484 #endif  /* CONFIG_ENV_FIT_UCBOOT */
 485
 486 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 487 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 488
 489 /*
 490  * Command line configuration.
 491  */
 492 #define CONFIG_CMD_IRQ
 493 #define CONFIG_CMD_PING
 494 #define CONFIG_CMD_I2C
 495 #define CONFIG_CMD_MII
 496 #define CONFIG_CMD_DATE
 497 #define CONFIG_CMD_I2C
 498 #define CONFIG_CMD_IRQ
 499 #define CONFIG_CMD_MII
 500 #define CONFIG_CMD_PING
 501 #define CONFIG_CMD_REGINFO
 502 #define CONFIG_CMD_ERRATA
 503 #define CONFIG_CMD_CRAMFS
 504 #define CONFIG_CRAMFS_CMDLINE
 505
 506 /*
 507  * USB
 508  */
 509 #define CONFIG_HAS_FSL_DR_USB
 510
 511 #if defined(CONFIG_HAS_FSL_DR_USB)
 512 #define CONFIG_USB_EHCI
 513
 514 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 515
 516 #ifdef CONFIG_USB_EHCI
 517 #define CONFIG_CMD_USB
 518 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 519 #define CONFIG_USB_EHCI_FSL
 520 #define CONFIG_USB_STORAGE
 521 #endif
 522 #endif
 523
 524 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 525
 526 #ifdef CONFIG_MMC
 527 #define CONFIG_FSL_ESDHC
 528 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 529 #define CONFIG_CMD_MMC
 530 #define CONFIG_MMC_SPI
 531 #define CONFIG_CMD_MMC_SPI
 532 #define CONFIG_GENERIC_MMC
 533 #endif
 534
 535 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
 536 #define CONFIG_CMD_EXT2
 537 #define CONFIG_CMD_FAT
 538 #define CONFIG_DOS_PARTITION
 539 #endif
 540
 541 /* Misc Extra Settings */
 542 #define CONFIG_CMD_GPIO                 1
 543 #undef CONFIG_WATCHDOG  /* watchdog disabled */
 544
 545 /*
 546  * Miscellaneous configurable options
 547  */
 548 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 549 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 550 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 551 #if defined(CONFIG_CMD_KGDB)
 552 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 553 #else
 554 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 555 #endif
 556 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 557         /* Print Buffer Size */
 558 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 559 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 560 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms tick */
 561
 562 /*
 563  * For booting Linux, the board info and command line data
 564  * have to be in the first 64 MB of memory, since this is
 565  * the maximum mapped by the Linux kernel during initialization.
 566  */
 567 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux*/
 568 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 569
 570 #if defined(CONFIG_CMD_KGDB)
 571 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 572 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 573 #endif
 574
 575 /*
 576  * Environment Configuration
 577  */
 578
 579 #if defined(CONFIG_TSEC_ENET)
 580
 581 #if defined(CONFIG_UCP1020_REV_1_2)
 582 #define CONFIG_PHY_MICREL_KSZ9021
 583 #elif defined(CONFIG_UCP1020_REV_1_3)
 584 #define CONFIG_PHY_MICREL_KSZ9031
 585 #else
 586 #error "UCP1020 module revision is not defined !!!"
 587 #endif
 588
 589 #define CONFIG_CMD_DHCP
 590 #define CONFIG_BOOTP_SERVERIP
 591
 592 #define CONFIG_MII              /* MII PHY management */
 593 #define CONFIG_TSEC1_NAME       "eTSEC1"
 594 #define CONFIG_TSEC2_NAME       "eTSEC2"
 595 #define CONFIG_TSEC3_NAME       "eTSEC3"
 596
 597 #define TSEC1_PHY_ADDR  4
 598 #define TSEC2_PHY_ADDR  0
 599 #define TSEC2_PHY_ADDR_SGMII    0x00
 600 #define TSEC3_PHY_ADDR  6
 601
 602 #define TSEC1_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 603 #define TSEC2_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 604 #define TSEC3_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 605
 606 #define TSEC1_PHYIDX    0
 607 #define TSEC2_PHYIDX    0
 608 #define TSEC3_PHYIDX    0
 609
 610 #define CONFIG_PHY_GIGE 1       /* Include GbE speed/duplex detection */
 611
 612 #endif
 613
 614 #define CONFIG_HOSTNAME         UCP1020
 615 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 616 #define CONFIG_BOOTFILE         "uImage"
 617 #define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */
 618
 619 /* default location for tftp and bootm */
 620 #define CONFIG_LOADADDR         1000000
 621
 622 #define CONFIG_BOOTARGS /* the boot command will set bootargs */
 623
 624 #define CONFIG_BAUDRATE 115200
 625
 626 #if defined(CONFIG_DONGLE)
 627
 628 #define CONFIG_BOOTDELAY 1      /* autoboot after 1 seconds */
 629 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 630 "bootcmd=run prog_spi_mbrbootcramfs\0"                                  \
 631 "bootfile=uImage\0"                                                     \
 632 "consoledev=ttyS0\0"                                                    \
 633 "cramfsfile=image.cramfs\0"                                             \
 634 "dtbaddr=0x00c00000\0"                                                  \
 635 "dtbfile=image.dtb\0"                                                   \
 636 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 637 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 638 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 639 "fileaddr=0x01000000\0"                                                 \
 640 "filesize=0x00080000\0"                                                 \
 641 "flashmbr=sf probe 0; "                                                 \
 642         "tftp $loadaddr $mbr; "                                         \
 643         "sf erase $mbr_offset +$filesize; "                             \
 644         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 645 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 646         "protect off $nor_recoveryaddr +$filesize; "                    \
 647         "erase $nor_recoveryaddr +$filesize; "                          \
 648         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 649         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 650 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 651         "protect off $nor_ubootaddr +$filesize; "                       \
 652         "erase $nor_ubootaddr +$filesize; "                             \
 653         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 654         "protect on $nor_ubootaddr +$filesize\0 "                       \
 655 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 656         "protect off $nor_workingaddr +$filesize; "                     \
 657         "erase $nor_workingaddr +$filesize; "                           \
 658         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 659         "protect on $nor_workingaddr +$filesize\0 "                     \
 660 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 661 "kerneladdr=0x01100000\0"                                               \
 662 "kernelfile=uImage\0"                                                   \
 663 "loadaddr=0x01000000\0"                                                 \
 664 "mbr=uCP1020d.mbr\0"                                                    \
 665 "mbr_offset=0x00000000\0"                                               \
 666 "mmbr=uCP1020Quiet.mbr\0"                                               \
 667 "mmcpart=0:2\0"                                                         \
 668 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 669         "mmc erase 1 1; "                                               \
 670         "mmc write $loadaddr 1 1\0"                                     \
 671 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; "                \
 672         "mmc erase 0x40 0x400; "                                        \
 673         "mmc write $loadaddr 0x40 0x400\0"                              \
 674 "netdev=eth0\0"                                                         \
 675 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 676 "nor_ubootaddr=0xEFF80000\0"                                            \
 677 "nor_workingaddr=0xECFA0000\0"                                          \
 678 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 679         " console=$consoledev,$baudrate $othbootargs; "                 \
 680         "run norloadrecovery; "                                         \
 681         "bootm $kerneladdr - $dtbaddr\0"                                \
 682 "norbootworking=setenv bootargs $workingbootargs"                       \
 683         " console=$consoledev,$baudrate $othbootargs; "                 \
 684         "run norloadworking; "                                          \
 685         "bootm $kerneladdr - $dtbaddr\0"                                \
 686 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 687         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 688         "cramfsload $dtbaddr $dtbfile; "                                \
 689         "cramfsload $kerneladdr $kernelfile\0"                          \
 690 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 691         "setenv cramfsaddr $nor_workingaddr; "                          \
 692         "cramfsload $dtbaddr $dtbfile; "                                \
 693         "cramfsload $kerneladdr $kernelfile\0"                          \
 694 "prog_spi_mbr=run spi__mbr\0"                                           \
 695 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0"       \
 696 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
 697         "run spi__cramfs\0"                                             \
 698 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 699         " console=$consoledev,$baudrate $othbootargs; "                 \
 700         "tftp $rootfsaddr $rootfsfile; "                                \
 701         "tftp $loadaddr $kernelfile; "                                  \
 702         "tftp $dtbaddr $dtbfile; "                                      \
 703         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 704 "ramdisk_size=120000\0"                                                 \
 705 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 706 "recoveryaddr=0x02F00000\0"                                             \
 707 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 708 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 709         "mw.l 0xffe0f008 0x00400000\0"                                  \
 710 "rootfsaddr=0x02F00000\0"                                               \
 711 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 712 "rootpath=/opt/nfsroot\0"                                               \
 713 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 714         "protect off 0xeC000000 +$filesize; "                           \
 715         "erase 0xEC000000 +$filesize; "                                 \
 716         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 717         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 718         "protect on 0xeC000000 +$filesize\0"                            \
 719 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 720         "protect off 0xeFF80000 +$filesize; "                           \
 721         "erase 0xEFF80000 +$filesize; "                                 \
 722         "cp.b $loadaddr 0xEFF80000 $filesize; "                         \
 723         "cmp.b $loadaddr 0xEFF80000 $filesize; "                        \
 724         "protect on 0xeFF80000 +$filesize\0"                            \
 725 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; "                   \
 726         "sf probe 0; sf erase 0x8000 +$filesize; "                      \
 727         "sf write $loadaddr 0x8000 $filesize\0"                         \
 728 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; "             \
 729         "protect off 0xec0a0000 +$filesize; "                           \
 730         "erase 0xeC0A0000 +$filesize; "                                 \
 731         "cp.b $loadaddr 0xeC0A0000 $filesize; "                         \
 732         "protect on 0xec0a0000 +$filesize\0"                            \
 733 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 734         "sf probe 1; sf erase 0 +$filesize; "                           \
 735         "sf write $loadaddr 0 $filesize\0"                              \
 736 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 737         "sf probe 0; sf erase 0 +$filesize; "                           \
 738         "sf write $loadaddr 0 $filesize\0"                              \
 739 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 740         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 741         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 742         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 743         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 744         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 745 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 746 "ubootaddr=0x01000000\0"                                                \
 747 "ubootfile=u-boot.bin\0"                                                \
 748 "ubootd=u-boot4dongle.bin\0"                                            \
 749 "upgrade=run flashworking\0"                                            \
 750 "usb_phy_type=ulpi\0 "                                                  \
 751 "workingaddr=0x02F00000\0"                                              \
 752 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 753
 754 #else
 755
 756 #if defined(CONFIG_UCP1020T1)
 757
 758 #define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
 759 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 760 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0"  \
 761 "bootfile=uImage\0"                                                     \
 762 "consoledev=ttyS0\0"                                                    \
 763 "cramfsfile=image.cramfs\0"                                             \
 764 "dtbaddr=0x00c00000\0"                                                  \
 765 "dtbfile=image.dtb\0"                                                   \
 766 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 767 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 768 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 769 "fileaddr=0x01000000\0"                                                 \
 770 "filesize=0x00080000\0"                                                 \
 771 "flashmbr=sf probe 0; "                                                 \
 772         "tftp $loadaddr $mbr; "                                         \
 773         "sf erase $mbr_offset +$filesize; "                             \
 774         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 775 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 776         "protect off $nor_recoveryaddr +$filesize; "                    \
 777         "erase $nor_recoveryaddr +$filesize; "                          \
 778         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 779         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 780 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 781         "protect off $nor_ubootaddr +$filesize; "                       \
 782         "erase $nor_ubootaddr +$filesize; "                             \
 783         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 784         "protect on $nor_ubootaddr +$filesize\0 "                       \
 785 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 786         "protect off $nor_workingaddr +$filesize; "                     \
 787         "erase $nor_workingaddr +$filesize; "                           \
 788         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 789         "protect on $nor_workingaddr +$filesize\0 "                     \
 790 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 791 "kerneladdr=0x01100000\0"                                               \
 792 "kernelfile=uImage\0"                                                   \
 793 "loadaddr=0x01000000\0"                                                 \
 794 "mbr=uCP1020.mbr\0"                                                     \
 795 "mbr_offset=0x00000000\0"                                               \
 796 "netdev=eth0\0"                                                         \
 797 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 798 "nor_ubootaddr=0xEFF80000\0"                                            \
 799 "nor_workingaddr=0xECFA0000\0"                                          \
 800 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 801         " console=$consoledev,$baudrate $othbootargs; "                 \
 802         "run norloadrecovery; "                                         \
 803         "bootm $kerneladdr - $dtbaddr\0"                                \
 804 "norbootworking=setenv bootargs $workingbootargs"                       \
 805         " console=$consoledev,$baudrate $othbootargs; "                 \
 806         "run norloadworking; "                                          \
 807         "bootm $kerneladdr - $dtbaddr\0"                                \
 808 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 809         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 810         "cramfsload $dtbaddr $dtbfile; "                                \
 811         "cramfsload $kerneladdr $kernelfile\0"                          \
 812 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 813         "setenv cramfsaddr $nor_workingaddr; "                          \
 814         "cramfsload $dtbaddr $dtbfile; "                                \
 815         "cramfsload $kerneladdr $kernelfile\0"                          \
 816 "othbootargs=quiet\0"                                                   \
 817 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 818         " console=$consoledev,$baudrate $othbootargs; "                 \
 819         "tftp $rootfsaddr $rootfsfile; "                                \
 820         "tftp $loadaddr $kernelfile; "                                  \
 821         "tftp $dtbaddr $dtbfile; "                                      \
 822         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 823 "ramdisk_size=120000\0"                                                 \
 824 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 825 "recoveryaddr=0x02F00000\0"                                             \
 826 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 827 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 828         "mw.l 0xffe0f008 0x00400000\0"                                  \
 829 "rootfsaddr=0x02F00000\0"                                               \
 830 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 831 "rootpath=/opt/nfsroot\0"                                               \
 832 "silent=1\0"                                                            \
 833 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 834         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 835         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 836         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 837         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 838         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 839 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 840 "ubootaddr=0x01000000\0"                                                \
 841 "ubootfile=u-boot.bin\0"                                                \
 842 "upgrade=run flashworking\0"                                            \
 843 "workingaddr=0x02F00000\0"                                              \
 844 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 845
 846 #else /* For Arcturus Modules */
 847
 848 #define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
 849 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 850 "bootcmd=run norkernel\0"                                               \
 851 "bootfile=uImage\0"                                                     \
 852 "consoledev=ttyS0\0"                                                    \
 853 "dtbaddr=0x00c00000\0"                                                  \
 854 "dtbfile=image.dtb\0"                                                   \
 855 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 856 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 857 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 858 "fileaddr=0x01000000\0"                                                 \
 859 "filesize=0x00080000\0"                                                 \
 860 "flashmbr=sf probe 0; "                                                 \
 861         "tftp $loadaddr $mbr; "                                         \
 862         "sf erase $mbr_offset +$filesize; "                             \
 863         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 864 "flashuboot=tftp $loadaddr $ubootfile; "                                \
 865         "protect off $nor_ubootaddr0 +$filesize; "                      \
 866         "erase $nor_ubootaddr0 +$filesize; "                            \
 867         "cp.b $loadaddr $nor_ubootaddr0 $filesize; "                    \
 868         "protect on $nor_ubootaddr0 +$filesize; "                       \
 869         "protect off $nor_ubootaddr1 +$filesize; "                      \
 870         "erase $nor_ubootaddr1 +$filesize; "                            \
 871         "cp.b $loadaddr $nor_ubootaddr1 $filesize; "                    \
 872         "protect on $nor_ubootaddr1 +$filesize\0 "                      \
 873 "format0=protect off $part0base +$part0size; "                          \
 874         "erase $part0base +$part0size\0"                                \
 875 "format1=protect off $part1base +$part1size; "                          \
 876         "erase $part1base +$part1size\0"                                \
 877 "format2=protect off $part2base +$part2size; "                          \
 878         "erase $part2base +$part2size\0"                                \
 879 "format3=protect off $part3base +$part3size; "                          \
 880         "erase $part3base +$part3size\0"                                \
 881 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 882 "kerneladdr=0x01100000\0"                                               \
 883 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"                 \
 884 "kernelfile=uImage\0"                                                   \
 885 "loadaddr=0x01000000\0"                                                 \
 886 "mbr=uCP1020.mbr\0"                                                     \
 887 "mbr_offset=0x00000000\0"                                               \
 888 "netdev=eth0\0"                                                         \
 889 "nor_ubootaddr0=0xEC000000\0"                                           \
 890 "nor_ubootaddr1=0xEFF80000\0"                                           \
 891 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
 892         "run norkernelload; "                                           \
 893         "bootm $kerneladdr - $dtbaddr\0"                                \
 894 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; "                       \
 895         "setenv cramfsaddr $part0base; "                                \
 896         "cramfsload $dtbaddr $dtbfile; "                                \
 897         "cramfsload $kerneladdr $kernelfile\0"                          \
 898 "part0base=0xEC100000\0"                                                \
 899 "part0size=0x00700000\0"                                                \
 900 "part1base=0xEC800000\0"                                                \
 901 "part1size=0x02000000\0"                                                \
 902 "part2base=0xEE800000\0"                                                \
 903 "part2size=0x00800000\0"                                                \
 904 "part3base=0xEF000000\0"                                                \
 905 "part3size=0x00F80000\0"                                                \
 906 "partENVbase=0xEC080000\0"                                              \
 907 "partENVsize=0x00080000\0"                                              \
 908 "program0=tftp part0-000000.bin; "                                      \
 909         "protect off $part0base +$filesize; "                           \
 910         "erase $part0base +$filesize; "                                 \
 911         "cp.b $loadaddr $part0base $filesize; "                         \
 912         "echo Verifying...; "                                           \
 913         "cmp.b $loadaddr $part0base $filesize\0"                        \
 914 "program1=tftp part1-000000.bin; "                                      \
 915         "protect off $part1base +$filesize; "                           \
 916         "erase $part1base +$filesize; "                                 \
 917         "cp.b $loadaddr $part1base $filesize; "                         \
 918         "echo Verifying...; "                                           \
 919         "cmp.b $loadaddr $part1base $filesize\0"                        \
 920 "program2=tftp part2-000000.bin; "                                      \
 921         "protect off $part2base +$filesize; "                           \
 922         "erase $part2base +$filesize; "                                 \
 923         "cp.b $loadaddr $part2base $filesize; "                         \
 924         "echo Verifying...; "                                           \
 925         "cmp.b $loadaddr $part2base $filesize\0"                        \
 926 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 927         "  console=$consoledev,$baudrate $othbootargs; "                \
 928         "tftp $rootfsaddr $rootfsfile; "                                \
 929         "tftp $loadaddr $kernelfile; "                                  \
 930         "tftp $dtbaddr $dtbfile; "                                      \
 931         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 932 "ramdisk_size=120000\0"                                                 \
 933 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 934 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 935         "mw.l 0xffe0f008 0x00400000\0"                                  \
 936 "rootfsaddr=0x02F00000\0"                                               \
 937 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 938 "rootpath=/opt/nfsroot\0"                                               \
 939 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 940         "sf probe 0; sf erase 0 +$filesize; "                           \
 941         "sf write $loadaddr 0 $filesize\0"                              \
 942 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; "                 \
 943         "protect off 0xeC000000 +$filesize; "                           \
 944         "erase 0xEC000000 +$filesize; "                                 \
 945         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 946         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 947         "protect on 0xeC000000 +$filesize\0"                            \
 948 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 949         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 950         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 951         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 952         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 953         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 954 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 955 "ubootfile=u-boot.bin\0"                                                \
 956 "upgrade=run flashuboot\0"                                              \
 957 "usb_phy_type=ulpi\0 "                                                  \
 958 "boot_nfs= "                                                            \
 959         "setenv bootargs root=/dev/nfs rw "                             \
 960         "nfsroot=$serverip:$rootpath "                                  \
 961         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 962         "console=$consoledev,$baudrate $othbootargs;"                   \
 963         "tftp $loadaddr $bootfile;"                                     \
 964         "tftp $fdtaddr $fdtfile;"                                       \
 965         "bootm $loadaddr - $fdtaddr\0"                                  \
 966 "boot_hd = "                                                            \
 967         "setenv bootargs root=/dev/$bdev rw rootdelay=30 "              \
 968         "console=$consoledev,$baudrate $othbootargs;"                   \
 969         "usb start;"                                                    \
 970         "ext2load usb 0:1 $loadaddr /boot/$bootfile;"                   \
 971         "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"                     \
 972         "bootm $loadaddr - $fdtaddr\0"                                  \
 973 "boot_usb_fat = "                                                       \
 974         "setenv bootargs root=/dev/ram rw "                             \
 975         "console=$consoledev,$baudrate $othbootargs "                   \
 976         "ramdisk_size=$ramdisk_size;"                                   \
 977         "usb start;"                                                    \
 978         "fatload usb 0:2 $loadaddr $bootfile;"                          \
 979         "fatload usb 0:2 $fdtaddr $fdtfile;"                            \
 980         "fatload usb 0:2 $ramdiskaddr $ramdiskfile;"                    \
 981         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 982 "boot_usb_ext2 = "                                                      \
 983         "setenv bootargs root=/dev/ram rw "                             \
 984         "console=$consoledev,$baudrate $othbootargs "                   \
 985         "ramdisk_size=$ramdisk_size;"                                   \
 986         "usb start;"                                                    \
 987         "ext2load usb 0:4 $loadaddr $bootfile;"                         \
 988         "ext2load usb 0:4 $fdtaddr $fdtfile;"                           \
 989         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"                   \
 990         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 991 "boot_nor = "                                                           \
 992         "setenv bootargs root=/dev/$jffs2nor rw "                       \
 993         "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"  \
 994         "bootm $norbootaddr - $norfdtaddr\0 "                           \
 995 "boot_ram = "                                                           \
 996         "setenv bootargs root=/dev/ram rw "                             \
 997         "console=$consoledev,$baudrate $othbootargs "                   \
 998         "ramdisk_size=$ramdisk_size;"                                   \
 999         "tftp $ramdiskaddr $ramdiskfile;"                               \
1000         "tftp $loadaddr $bootfile;"                                     \
1001         "tftp $fdtaddr $fdtfile;"                                       \
1002         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
1003
1004 #endif
1005 #endif
1006
1007 #endif /* __CONFIG_H */