include/configs/UCP1020.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2013-2019 Arcturus Networks, Inc.
   4  *           https://www.arcturusnetworks.com/products/ucp1020/
   5  * based on include/configs/p1_p2_rdb_pc.h
   6  * original copyright follows:
   7  * Copyright 2009-2011 Freescale Semiconductor, Inc.
   8  */
   9
  10 /*
  11  * QorIQ uCP1020-xx boards configuration file
  12  */
  13 #ifndef __CONFIG_H
  14 #define __CONFIG_H
  15
  16 /*** Arcturus FirmWare Environment */
  17
  18 #define MAX_SERIAL_SIZE 15
  19 #define MAX_HWADDR_SIZE 17
  20
  21 #define MAX_FWENV_ADDR  4
  22
  23 #define FWENV_MMC       1
  24 #define FWENV_SPI_FLASH 2
  25 #define FWENV_NOR_FLASH 3
  26 /*
  27  #define FWENV_TYPE    FWENV_MMC
  28  #define FWENV_TYPE    FWENV_SPI_FLASH
  29 */
  30 #define FWENV_TYPE      FWENV_NOR_FLASH
  31
  32 #if (FWENV_TYPE == FWENV_MMC)
  33 #ifndef CONFIG_SYS_MMC_ENV_DEV
  34 #define CONFIG_SYS_MMC_ENV_DEV 1
  35 #endif
  36 #define FWENV_ADDR1 -1
  37 #define FWENV_ADDR2 -1
  38 #define FWENV_ADDR3 -1
  39 #define FWENV_ADDR4 -1
  40 #define EMPY_CHAR 0
  41 #endif
  42
  43 #if (FWENV_TYPE == FWENV_SPI_FLASH)
  44 #ifndef CONFIG_SF_DEFAULT_SPEED
  45 #define CONFIG_SF_DEFAULT_SPEED 1000000
  46 #endif
  47 #ifndef CONFIG_SF_DEFAULT_MODE
  48 #define CONFIG_SF_DEFAULT_MODE  SPI_MODE0
  49 #endif
  50 #ifndef CONFIG_SF_DEFAULT_CS
  51 #define CONFIG_SF_DEFAULT_CS    0
  52 #endif
  53 #ifndef CONFIG_SF_DEFAULT_BUS
  54 #define CONFIG_SF_DEFAULT_BUS   0
  55 #endif
  56 #define FWENV_ADDR1 (0x200 - sizeof(smac))
  57 #define FWENV_ADDR2 (0x400 - sizeof(smac))
  58 #define FWENV_ADDR3 (CONFIG_ENV_SECT_SIZE + 0x200 - sizeof(smac))
  59 #define FWENV_ADDR4 (CONFIG_ENV_SECT_SIZE + 0x400 - sizeof(smac))
  60 #define EMPY_CHAR 0xff
  61 #endif
  62
  63 #if (FWENV_TYPE == FWENV_NOR_FLASH)
  64 #define FWENV_ADDR1 0xEC080000
  65 #define FWENV_ADDR2 -1
  66 #define FWENV_ADDR3 -1
  67 #define FWENV_ADDR4 -1
  68 #define EMPY_CHAR 0xff
  69 #endif
  70 /***********************************/
  71
  72 #define CONFIG_PCIE1    /* PCIE controller 1 (slot 1) */
  73 #define CONFIG_PCIE2    /* PCIE controller 2 (slot 2) */
  74 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
  75 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
  76 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
  77
  78 #if defined(CONFIG_TARTGET_UCP1020T1)
  79
  80 #define CONFIG_UCP1020_REV_1_3
  81
  82 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
  83
  84 #define CONFIG_TSEC1
  85 #define CONFIG_TSEC3
  86 #define CONFIG_HAS_ETH0
  87 #define CONFIG_HAS_ETH1
  88 #define CONFIG_ETHADDR          00:19:D3:FF:FF:FF
  89 #define CONFIG_ETH1ADDR         00:19:D3:FF:FF:FE
  90 #define CONFIG_ETH2ADDR         00:19:D3:FF:FF:FD
  91 #define CONFIG_IPADDR           10.80.41.229
  92 #define CONFIG_SERVERIP         10.80.41.227
  93 #define CONFIG_NETMASK          255.255.252.0
  94 #define CONFIG_ETHPRIME         "eTSEC3"
  95
  96 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  97
  98 #endif
  99
 100 #if defined(CONFIG_TARGET_UCP1020)
 101
 102 #define CONFIG_UCP1020
 103 #define CONFIG_UCP1020_REV_1_3
 104
 105 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
 106
 107 #define CONFIG_TSEC1
 108 #define CONFIG_TSEC3
 109 #define CONFIG_HAS_ETH0
 110 #define CONFIG_HAS_ETH1
 111 #define CONFIG_HAS_ETH2
 112 #define CONFIG_ETHADDR          00:06:3B:FF:FF:FF
 113 #define CONFIG_ETH1ADDR         00:06:3B:FF:FF:FE
 114 #define CONFIG_ETH2ADDR         00:06:3B:FF:FF:FD
 115 #define CONFIG_IPADDR           192.168.1.81
 116 #define CONFIG_IPADDR1          192.168.1.82
 117 #define CONFIG_IPADDR2          192.168.1.83
 118 #define CONFIG_SERVERIP         192.168.1.80
 119 #define CONFIG_GATEWAYIP        102.168.1.1
 120 #define CONFIG_NETMASK          255.255.255.0
 121 #define CONFIG_ETHPRIME         "eTSEC1"
 122
 123 #undef CONFIG_SYS_REDUNDAND_ENVIRONMENT
 124
 125 #define CONFIG_SYS_L2_SIZE      (256 << 10)
 126
 127 #endif
 128
 129 #ifdef CONFIG_SDCARD
 130 #define CONFIG_RAMBOOT_SDCARD
 131 #define CONFIG_SYS_RAMBOOT
 132 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
 133 #endif
 134
 135 #ifdef CONFIG_SPIFLASH
 136 #define CONFIG_RAMBOOT_SPIFLASH
 137 #define CONFIG_SYS_RAMBOOT
 138 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
 139 #endif
 140
 141 #define CONFIG_SYS_TEXT_BASE_NOR        0xeff80000
 142
 143 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 144 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 145 #endif
 146
 147 #ifndef CONFIG_SYS_MONITOR_BASE
 148 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 149 #endif
 150
 151 #define CONFIG_ENV_OVERWRITE
 152
 153 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 154 #define CONFIG_LBA48
 155
 156 #define CONFIG_SYS_CLK_FREQ     66666666
 157 #define CONFIG_DDR_CLK_FREQ     66666666
 158
 159 #define CONFIG_HWCONFIG
 160
 161 /*
 162  * These can be toggled for performance analysis, otherwise use default.
 163  */
 164 #define CONFIG_L2_CACHE
 165 #define CONFIG_BTB
 166
 167 #define CONFIG_ENABLE_36BIT_PHYS
 168
 169 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 170 #define CONFIG_SYS_MEMTEST_END          0x1fffffff
 171
 172 #define CONFIG_SYS_CCSRBAR              0xffe00000
 173 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
 174
 175 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
 176        SPL code*/
 177 #ifdef CONFIG_SPL_BUILD
 178 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 179 #endif
 180
 181 /* DDR Setup */
 182 #define CONFIG_DDR_ECC_ENABLE
 183 #ifndef CONFIG_DDR_ECC_ENABLE
 184 #define CONFIG_SYS_DDR_RAW_TIMING
 185 #define CONFIG_DDR_SPD
 186 #endif
 187 #define CONFIG_SYS_SPD_BUS_NUM 1
 188
 189 #define CONFIG_SYS_SDRAM_SIZE_LAW       LAW_SIZE_512M
 190 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
 191 #define CONFIG_SYS_SDRAM_SIZE           (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
 192 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 193 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 194
 195 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 196
 197 /* Default settings for DDR3 */
 198 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
 199 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
 200 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
 201 #define CONFIG_SYS_DDR_CS1_BNDS         0x0040007f
 202 #define CONFIG_SYS_DDR_CS1_CONFIG       0x80014302
 203 #define CONFIG_SYS_DDR_CS1_CONFIG_2     0x00000000
 204
 205 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 206 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
 207 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
 208 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
 209
 210 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
 211 #define CONFIG_SYS_DDR_WRLVL_CONTROL    0x8655A608
 212 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
 213 #define CONFIG_SYS_DDR_RCW_1            0x00000000
 214 #define CONFIG_SYS_DDR_RCW_2            0x00000000
 215 #ifdef CONFIG_DDR_ECC_ENABLE
 216 #define CONFIG_SYS_DDR_CONTROL          0xE70C0000      /* Type = DDR3 & ECC */
 217 #else
 218 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3 */
 219 #endif
 220 #define CONFIG_SYS_DDR_CONTROL_2        0x04401050
 221 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 222 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 223
 224 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 225 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
 226 #define CONFIG_SYS_DDR_TIMING_1         0x6f6B4846
 227 #define CONFIG_SYS_DDR_TIMING_2         0x0FA8C8CF
 228 #define CONFIG_SYS_DDR_CLK_CTRL         0x03000000
 229 #define CONFIG_SYS_DDR_MODE_1           0x40461520
 230 #define CONFIG_SYS_DDR_MODE_2           0x8000c000
 231 #define CONFIG_SYS_DDR_INTERVAL         0x0C300000
 232
 233 #undef CONFIG_CLOCKS_IN_MHZ
 234
 235 /*
 236  * Memory map
 237  *
 238  * 0x0000_0000 0x7fff_ffff      DDR             Up to 2GB cacheable
 239  * 0x8000_0000 0xdfff_ffff      PCI Express Mem 1G non-cacheable(PCIe * 2)
 240  * 0xec00_0000 0xefff_ffff      NOR flash       Up to 64M non-cacheable CS0/1
 241  * 0xf8f8_0000 0xf8ff_ffff      L2 SRAM         Up to 256K cacheable
 242  *   (early boot only)
 243  * 0xffc0_0000 0xffc3_ffff      PCI IO range    256k non-cacheable
 244  * 0xffd0_0000 0xffd0_3fff      L1 for stack    16K cacheable
 245  * 0xffe0_0000 0xffef_ffff      CCSR            1M non-cacheable
 246  */
 247
 248 /*
 249  * Local Bus Definitions
 250  */
 251 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* 64M */
 252 #define CONFIG_SYS_FLASH_BASE           0xec000000
 253
 254 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 255
 256 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 257         | BR_PS_16 | BR_V)
 258
 259 #define CONFIG_FLASH_OR_PRELIM          0xfc000ff7
 260
 261 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
 262 #define CONFIG_SYS_FLASH_QUIET_TEST
 263 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 264
 265 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 266
 267 #undef CONFIG_SYS_FLASH_CHECKSUM
 268 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 269 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 270
 271 #define CONFIG_SYS_FLASH_EMPTY_INFO
 272
 273 #define CONFIG_SYS_INIT_RAM_LOCK
 274 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000 /* stack in RAM */
 275 /* Initial L1 address */
 276 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 277 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 278 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 279 /* Size of used area in RAM */
 280 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 281
 282 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 283                                         GENERATED_GBL_DATA_SIZE)
 284 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 285
 286 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)/* Reserve 256 kB for Mon */
 287 #define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)/* Reserved for malloc */
 288
 289 #define CONFIG_SYS_PMC_BASE     0xff980000
 290 #define CONFIG_SYS_PMC_BASE_PHYS        CONFIG_SYS_PMC_BASE
 291 #define CONFIG_PMC_BR_PRELIM    (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
 292                                         BR_PS_8 | BR_V)
 293 #define CONFIG_PMC_OR_PRELIM    (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
 294                                  OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
 295                                  OR_GPCM_EAD)
 296
 297 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 298 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 299 #ifdef CONFIG_NAND_FSL_ELBC
 300 #define CONFIG_SYS_BR1_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
 301 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 302 #endif
 303
 304 /* Serial Port - controlled on board with jumper J8
 305  * open - index 2
 306  * shorted - index 1
 307  */
 308 #undef CONFIG_SERIAL_SOFTWARE_FIFO
 309 #define CONFIG_SYS_NS16550_SERIAL
 310 #define CONFIG_SYS_NS16550_REG_SIZE     1
 311 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 312 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
 313 #define CONFIG_NS16550_MIN_FUNCTIONS
 314 #endif
 315
 316 #define CONFIG_SYS_BAUDRATE_TABLE       \
 317         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 318
 319 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
 320 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
 321
 322 /* I2C */
 323 #define CONFIG_SYS_I2C
 324 #define CONFIG_SYS_I2C_FSL
 325 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 326 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 327 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 328 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 329 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 330 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 331 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x29} }
 332 #define CONFIG_SYS_SPD_BUS_NUM          1 /* For rom_loc and flash bank */
 333
 334 #define CONFIG_RTC_DS1337
 335 #define CONFIG_RTC_DS1337_NOOSC
 336 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 337 #define CONFIG_SYS_I2C_PCA9557_ADDR     0x18
 338 #define CONFIG_SYS_I2C_NCT72_ADDR       0x4C
 339 #define CONFIG_SYS_I2C_IDT6V49205B      0x69
 340
 341 #if defined(CONFIG_PCI)
 342 /*
 343  * General PCI
 344  * Memory space is mapped 1-1, but I/O space must start from 0.
 345  */
 346
 347 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 348 #define CONFIG_SYS_PCIE2_NAME           "PCIe SLOT CON9"
 349 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 350 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 351 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 352 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 353 #define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
 354 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 355 #define CONFIG_SYS_PCIE2_IO_PHYS        0xffc10000
 356 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 357
 358 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 359 #define CONFIG_SYS_PCIE1_NAME           "PCIe SLOT CON10"
 360 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 361 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 362 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 363 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 364 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 365 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 366 #define CONFIG_SYS_PCIE1_IO_PHYS        0xffc00000
 367 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 368
 369 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 370 #endif /* CONFIG_PCI */
 371
 372 /*
 373  * Environment
 374  */
 375 #ifdef CONFIG_ENV_FIT_UCBOOT
 376
 377 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x20000)
 378 #define CONFIG_ENV_SIZE         0x20000
 379 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 380
 381 #else
 382
 383
 384 #ifdef CONFIG_RAMBOOT_SPIFLASH
 385
 386 #define CONFIG_ENV_SIZE         0x3000          /* 12KB */
 387 #define CONFIG_ENV_OFFSET       0x2000          /* 8KB */
 388 #define CONFIG_ENV_SECT_SIZE    0x1000
 389
 390 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 391 /* Address and size of Redundant Environment Sector     */
 392 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 393 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 394 #endif
 395
 396 #elif defined(CONFIG_RAMBOOT_SDCARD)
 397 #define CONFIG_FSL_FIXED_MMC_LOCATION
 398 #define CONFIG_ENV_SIZE         0x2000
 399 #define CONFIG_SYS_MMC_ENV_DEV  0
 400
 401 #elif defined(CONFIG_SYS_RAMBOOT)
 402 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 403 #define CONFIG_ENV_SIZE         0x2000
 404
 405 #else
 406 #define CONFIG_ENV_BASE         (CONFIG_SYS_FLASH_BASE)
 407 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 408 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 409 #define CONFIG_ENV_ADDR         (CONFIG_ENV_BASE + 0xC0000)
 410 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 411 /* Address and size of Redundant Environment Sector     */
 412 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
 413 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 414 #endif
 415
 416 #endif
 417
 418 #endif  /* CONFIG_ENV_FIT_UCBOOT */
 419
 420 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 421 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 422
 423 /*
 424  * USB
 425  */
 426 #define CONFIG_HAS_FSL_DR_USB
 427
 428 #if defined(CONFIG_HAS_FSL_DR_USB)
 429 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 430
 431 #ifdef CONFIG_USB_EHCI_HCD
 432 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 433 #define CONFIG_USB_EHCI_FSL
 434 #endif
 435 #endif
 436
 437 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 438
 439 #ifdef CONFIG_MMC
 440 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 441 #define CONFIG_MMC_SPI
 442 #endif
 443
 444 /* Misc Extra Settings */
 445 #undef CONFIG_WATCHDOG  /* watchdog disabled */
 446
 447 /*
 448  * Miscellaneous configurable options
 449  */
 450 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 451 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms tick */
 452
 453 /*
 454  * For booting Linux, the board info and command line data
 455  * have to be in the first 64 MB of memory, since this is
 456  * the maximum mapped by the Linux kernel during initialization.
 457  */
 458 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux*/
 459 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 460
 461 #if defined(CONFIG_CMD_KGDB)
 462 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 463 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 464 #endif
 465
 466 /*
 467  * Environment Configuration
 468  */
 469
 470 #if defined(CONFIG_TSEC_ENET)
 471
 472 #if defined(CONFIG_UCP1020_REV_1_2) || defined(CONFIG_UCP1020_REV_1_3)
 473 #else
 474 #error "UCP1020 module revision is not defined !!!"
 475 #endif
 476
 477 #define CONFIG_BOOTP_SERVERIP
 478
 479 #define CONFIG_TSEC1_NAME       "eTSEC1"
 480 #define CONFIG_TSEC2_NAME       "eTSEC2"
 481 #define CONFIG_TSEC3_NAME       "eTSEC3"
 482
 483 #define TSEC1_PHY_ADDR  4
 484 #define TSEC2_PHY_ADDR  0
 485 #define TSEC2_PHY_ADDR_SGMII    0x00
 486 #define TSEC3_PHY_ADDR  6
 487
 488 #define TSEC1_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 489 #define TSEC2_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 490 #define TSEC3_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 491
 492 #define TSEC1_PHYIDX    0
 493 #define TSEC2_PHYIDX    0
 494 #define TSEC3_PHYIDX    0
 495
 496 #endif
 497
 498 #define CONFIG_HOSTNAME         "UCP1020"
 499 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 500 #define CONFIG_BOOTFILE         "uImage"
 501 #define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */
 502
 503 /* default location for tftp and bootm */
 504 #define CONFIG_LOADADDR         1000000
 505
 506 #if defined(CONFIG_DONGLE)
 507
 508 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 509 "bootcmd=run prog_spi_mbrbootcramfs\0"                                  \
 510 "bootfile=uImage\0"                                                     \
 511 "consoledev=ttyS0\0"                                                    \
 512 "cramfsfile=image.cramfs\0"                                             \
 513 "dtbaddr=0x00c00000\0"                                                  \
 514 "dtbfile=image.dtb\0"                                                   \
 515 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 516 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 517 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 518 "fileaddr=0x01000000\0"                                                 \
 519 "filesize=0x00080000\0"                                                 \
 520 "flashmbr=sf probe 0; "                                                 \
 521         "tftp $loadaddr $mbr; "                                         \
 522         "sf erase $mbr_offset +$filesize; "                             \
 523         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 524 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 525         "protect off $nor_recoveryaddr +$filesize; "                    \
 526         "erase $nor_recoveryaddr +$filesize; "                          \
 527         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 528         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 529 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 530         "protect off $nor_ubootaddr +$filesize; "                       \
 531         "erase $nor_ubootaddr +$filesize; "                             \
 532         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 533         "protect on $nor_ubootaddr +$filesize\0 "                       \
 534 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 535         "protect off $nor_workingaddr +$filesize; "                     \
 536         "erase $nor_workingaddr +$filesize; "                           \
 537         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 538         "protect on $nor_workingaddr +$filesize\0 "                     \
 539 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 540 "kerneladdr=0x01100000\0"                                               \
 541 "kernelfile=uImage\0"                                                   \
 542 "loadaddr=0x01000000\0"                                                 \
 543 "mbr=uCP1020d.mbr\0"                                                    \
 544 "mbr_offset=0x00000000\0"                                               \
 545 "mmbr=uCP1020Quiet.mbr\0"                                               \
 546 "mmcpart=0:2\0"                                                         \
 547 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 548         "mmc erase 1 1; "                                               \
 549         "mmc write $loadaddr 1 1\0"                                     \
 550 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; "                \
 551         "mmc erase 0x40 0x400; "                                        \
 552         "mmc write $loadaddr 0x40 0x400\0"                              \
 553 "netdev=eth0\0"                                                         \
 554 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 555 "nor_ubootaddr=0xEFF80000\0"                                            \
 556 "nor_workingaddr=0xECFA0000\0"                                          \
 557 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 558         " console=$consoledev,$baudrate $othbootargs; "                 \
 559         "run norloadrecovery; "                                         \
 560         "bootm $kerneladdr - $dtbaddr\0"                                \
 561 "norbootworking=setenv bootargs $workingbootargs"                       \
 562         " console=$consoledev,$baudrate $othbootargs; "                 \
 563         "run norloadworking; "                                          \
 564         "bootm $kerneladdr - $dtbaddr\0"                                \
 565 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 566         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 567         "cramfsload $dtbaddr $dtbfile; "                                \
 568         "cramfsload $kerneladdr $kernelfile\0"                          \
 569 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 570         "setenv cramfsaddr $nor_workingaddr; "                          \
 571         "cramfsload $dtbaddr $dtbfile; "                                \
 572         "cramfsload $kerneladdr $kernelfile\0"                          \
 573 "prog_spi_mbr=run spi__mbr\0"                                           \
 574 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0"       \
 575 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
 576         "run spi__cramfs\0"                                             \
 577 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 578         " console=$consoledev,$baudrate $othbootargs; "                 \
 579         "tftp $rootfsaddr $rootfsfile; "                                \
 580         "tftp $loadaddr $kernelfile; "                                  \
 581         "tftp $dtbaddr $dtbfile; "                                      \
 582         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 583 "ramdisk_size=120000\0"                                                 \
 584 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 585 "recoveryaddr=0x02F00000\0"                                             \
 586 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 587 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 588         "mw.l 0xffe0f008 0x00400000\0"                                  \
 589 "rootfsaddr=0x02F00000\0"                                               \
 590 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 591 "rootpath=/opt/nfsroot\0"                                               \
 592 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 593         "protect off 0xeC000000 +$filesize; "                           \
 594         "erase 0xEC000000 +$filesize; "                                 \
 595         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 596         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 597         "protect on 0xeC000000 +$filesize\0"                            \
 598 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 599         "protect off 0xeFF80000 +$filesize; "                           \
 600         "erase 0xEFF80000 +$filesize; "                                 \
 601         "cp.b $loadaddr 0xEFF80000 $filesize; "                         \
 602         "cmp.b $loadaddr 0xEFF80000 $filesize; "                        \
 603         "protect on 0xeFF80000 +$filesize\0"                            \
 604 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; "                   \
 605         "sf probe 0; sf erase 0x8000 +$filesize; "                      \
 606         "sf write $loadaddr 0x8000 $filesize\0"                         \
 607 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; "             \
 608         "protect off 0xec0a0000 +$filesize; "                           \
 609         "erase 0xeC0A0000 +$filesize; "                                 \
 610         "cp.b $loadaddr 0xeC0A0000 $filesize; "                         \
 611         "protect on 0xec0a0000 +$filesize\0"                            \
 612 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 613         "sf probe 1; sf erase 0 +$filesize; "                           \
 614         "sf write $loadaddr 0 $filesize\0"                              \
 615 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 616         "sf probe 0; sf erase 0 +$filesize; "                           \
 617         "sf write $loadaddr 0 $filesize\0"                              \
 618 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 619         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 620         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 621         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 622         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 623         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 624 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 625 "ubootaddr=0x01000000\0"                                                \
 626 "ubootfile=u-boot.bin\0"                                                \
 627 "ubootd=u-boot4dongle.bin\0"                                            \
 628 "upgrade=run flashworking\0"                                            \
 629 "usb_phy_type=ulpi\0 "                                                  \
 630 "workingaddr=0x02F00000\0"                                              \
 631 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 632
 633 #else
 634
 635 #if defined(CONFIG_UCP1020T1)
 636
 637 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 638 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0"  \
 639 "bootfile=uImage\0"                                                     \
 640 "consoledev=ttyS0\0"                                                    \
 641 "cramfsfile=image.cramfs\0"                                             \
 642 "dtbaddr=0x00c00000\0"                                                  \
 643 "dtbfile=image.dtb\0"                                                   \
 644 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 645 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 646 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 647 "fileaddr=0x01000000\0"                                                 \
 648 "filesize=0x00080000\0"                                                 \
 649 "flashmbr=sf probe 0; "                                                 \
 650         "tftp $loadaddr $mbr; "                                         \
 651         "sf erase $mbr_offset +$filesize; "                             \
 652         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 653 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 654         "protect off $nor_recoveryaddr +$filesize; "                    \
 655         "erase $nor_recoveryaddr +$filesize; "                          \
 656         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 657         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 658 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 659         "protect off $nor_ubootaddr +$filesize; "                       \
 660         "erase $nor_ubootaddr +$filesize; "                             \
 661         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 662         "protect on $nor_ubootaddr +$filesize\0 "                       \
 663 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 664         "protect off $nor_workingaddr +$filesize; "                     \
 665         "erase $nor_workingaddr +$filesize; "                           \
 666         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 667         "protect on $nor_workingaddr +$filesize\0 "                     \
 668 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 669 "kerneladdr=0x01100000\0"                                               \
 670 "kernelfile=uImage\0"                                                   \
 671 "loadaddr=0x01000000\0"                                                 \
 672 "mbr=uCP1020.mbr\0"                                                     \
 673 "mbr_offset=0x00000000\0"                                               \
 674 "netdev=eth0\0"                                                         \
 675 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 676 "nor_ubootaddr=0xEFF80000\0"                                            \
 677 "nor_workingaddr=0xECFA0000\0"                                          \
 678 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 679         " console=$consoledev,$baudrate $othbootargs; "                 \
 680         "run norloadrecovery; "                                         \
 681         "bootm $kerneladdr - $dtbaddr\0"                                \
 682 "norbootworking=setenv bootargs $workingbootargs"                       \
 683         " console=$consoledev,$baudrate $othbootargs; "                 \
 684         "run norloadworking; "                                          \
 685         "bootm $kerneladdr - $dtbaddr\0"                                \
 686 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 687         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 688         "cramfsload $dtbaddr $dtbfile; "                                \
 689         "cramfsload $kerneladdr $kernelfile\0"                          \
 690 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 691         "setenv cramfsaddr $nor_workingaddr; "                          \
 692         "cramfsload $dtbaddr $dtbfile; "                                \
 693         "cramfsload $kerneladdr $kernelfile\0"                          \
 694 "othbootargs=quiet\0"                                                   \
 695 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 696         " console=$consoledev,$baudrate $othbootargs; "                 \
 697         "tftp $rootfsaddr $rootfsfile; "                                \
 698         "tftp $loadaddr $kernelfile; "                                  \
 699         "tftp $dtbaddr $dtbfile; "                                      \
 700         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 701 "ramdisk_size=120000\0"                                                 \
 702 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 703 "recoveryaddr=0x02F00000\0"                                             \
 704 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 705 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 706         "mw.l 0xffe0f008 0x00400000\0"                                  \
 707 "rootfsaddr=0x02F00000\0"                                               \
 708 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 709 "rootpath=/opt/nfsroot\0"                                               \
 710 "silent=1\0"                                                            \
 711 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 712         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 713         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 714         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 715         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 716         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 717 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 718 "ubootaddr=0x01000000\0"                                                \
 719 "ubootfile=u-boot.bin\0"                                                \
 720 "upgrade=run flashworking\0"                                            \
 721 "workingaddr=0x02F00000\0"                                              \
 722 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 723
 724 #else /* For Arcturus Modules */
 725
 726 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 727 "bootcmd=run norkernel\0"                                               \
 728 "bootfile=uImage\0"                                                     \
 729 "consoledev=ttyS0\0"                                                    \
 730 "dtbaddr=0x00c00000\0"                                                  \
 731 "dtbfile=image.dtb\0"                                                   \
 732 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 733 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 734 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 735 "fileaddr=0x01000000\0"                                                 \
 736 "filesize=0x00080000\0"                                                 \
 737 "flashmbr=sf probe 0; "                                                 \
 738         "tftp $loadaddr $mbr; "                                         \
 739         "sf erase $mbr_offset +$filesize; "                             \
 740         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 741 "flashuboot=tftp $loadaddr $ubootfile; "                                \
 742         "protect off $nor_ubootaddr0 +$filesize; "                      \
 743         "erase $nor_ubootaddr0 +$filesize; "                            \
 744         "cp.b $loadaddr $nor_ubootaddr0 $filesize; "                    \
 745         "protect on $nor_ubootaddr0 +$filesize; "                       \
 746         "protect off $nor_ubootaddr1 +$filesize; "                      \
 747         "erase $nor_ubootaddr1 +$filesize; "                            \
 748         "cp.b $loadaddr $nor_ubootaddr1 $filesize; "                    \
 749         "protect on $nor_ubootaddr1 +$filesize\0 "                      \
 750 "format0=protect off $part0base +$part0size; "                          \
 751         "erase $part0base +$part0size\0"                                \
 752 "format1=protect off $part1base +$part1size; "                          \
 753         "erase $part1base +$part1size\0"                                \
 754 "format2=protect off $part2base +$part2size; "                          \
 755         "erase $part2base +$part2size\0"                                \
 756 "format3=protect off $part3base +$part3size; "                          \
 757         "erase $part3base +$part3size\0"                                \
 758 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 759 "kerneladdr=0x01100000\0"                                               \
 760 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"                 \
 761 "kernelfile=uImage\0"                                                   \
 762 "loadaddr=0x01000000\0"                                                 \
 763 "mbr=uCP1020.mbr\0"                                                     \
 764 "mbr_offset=0x00000000\0"                                               \
 765 "netdev=eth0\0"                                                         \
 766 "nor_ubootaddr0=0xEC000000\0"                                           \
 767 "nor_ubootaddr1=0xEFF80000\0"                                           \
 768 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
 769         "run norkernelload; "                                           \
 770         "bootm $kerneladdr - $dtbaddr\0"                                \
 771 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; "                       \
 772         "setenv cramfsaddr $part0base; "                                \
 773         "cramfsload $dtbaddr $dtbfile; "                                \
 774         "cramfsload $kerneladdr $kernelfile\0"                          \
 775 "part0base=0xEC100000\0"                                                \
 776 "part0size=0x00700000\0"                                                \
 777 "part1base=0xEC800000\0"                                                \
 778 "part1size=0x02000000\0"                                                \
 779 "part2base=0xEE800000\0"                                                \
 780 "part2size=0x00800000\0"                                                \
 781 "part3base=0xEF000000\0"                                                \
 782 "part3size=0x00F80000\0"                                                \
 783 "partENVbase=0xEC080000\0"                                              \
 784 "partENVsize=0x00080000\0"                                              \
 785 "program0=tftp part0-000000.bin; "                                      \
 786         "protect off $part0base +$filesize; "                           \
 787         "erase $part0base +$filesize; "                                 \
 788         "cp.b $loadaddr $part0base $filesize; "                         \
 789         "echo Verifying...; "                                           \
 790         "cmp.b $loadaddr $part0base $filesize\0"                        \
 791 "program1=tftp part1-000000.bin; "                                      \
 792         "protect off $part1base +$filesize; "                           \
 793         "erase $part1base +$filesize; "                                 \
 794         "cp.b $loadaddr $part1base $filesize; "                         \
 795         "echo Verifying...; "                                           \
 796         "cmp.b $loadaddr $part1base $filesize\0"                        \
 797 "program2=tftp part2-000000.bin; "                                      \
 798         "protect off $part2base +$filesize; "                           \
 799         "erase $part2base +$filesize; "                                 \
 800         "cp.b $loadaddr $part2base $filesize; "                         \
 801         "echo Verifying...; "                                           \
 802         "cmp.b $loadaddr $part2base $filesize\0"                        \
 803 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 804         "  console=$consoledev,$baudrate $othbootargs; "                \
 805         "tftp $rootfsaddr $rootfsfile; "                                \
 806         "tftp $loadaddr $kernelfile; "                                  \
 807         "tftp $dtbaddr $dtbfile; "                                      \
 808         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 809 "ramdisk_size=120000\0"                                                 \
 810 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 811 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 812         "mw.l 0xffe0f008 0x00400000\0"                                  \
 813 "rootfsaddr=0x02F00000\0"                                               \
 814 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 815 "rootpath=/opt/nfsroot\0"                                               \
 816 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 817         "sf probe 0; sf erase 0 +$filesize; "                           \
 818         "sf write $loadaddr 0 $filesize\0"                              \
 819 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; "                 \
 820         "protect off 0xeC000000 +$filesize; "                           \
 821         "erase 0xEC000000 +$filesize; "                                 \
 822         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 823         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 824         "protect on 0xeC000000 +$filesize\0"                            \
 825 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 826         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 827         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 828         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 829         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 830         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 831 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 832 "ubootfile=u-boot.bin\0"                                                \
 833 "upgrade=run flashuboot\0"                                              \
 834 "usb_phy_type=ulpi\0 "                                                  \
 835 "boot_nfs= "                                                            \
 836         "setenv bootargs root=/dev/nfs rw "                             \
 837         "nfsroot=$serverip:$rootpath "                                  \
 838         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 839         "console=$consoledev,$baudrate $othbootargs;"                   \
 840         "tftp $loadaddr $bootfile;"                                     \
 841         "tftp $fdtaddr $fdtfile;"                                       \
 842         "bootm $loadaddr - $fdtaddr\0"                                  \
 843 "boot_hd = "                                                            \
 844         "setenv bootargs root=/dev/$bdev rw rootdelay=30 "              \
 845         "console=$consoledev,$baudrate $othbootargs;"                   \
 846         "usb start;"                                                    \
 847         "ext2load usb 0:1 $loadaddr /boot/$bootfile;"                   \
 848         "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"                     \
 849         "bootm $loadaddr - $fdtaddr\0"                                  \
 850 "boot_usb_fat = "                                                       \
 851         "setenv bootargs root=/dev/ram rw "                             \
 852         "console=$consoledev,$baudrate $othbootargs "                   \
 853         "ramdisk_size=$ramdisk_size;"                                   \
 854         "usb start;"                                                    \
 855         "fatload usb 0:2 $loadaddr $bootfile;"                          \
 856         "fatload usb 0:2 $fdtaddr $fdtfile;"                            \
 857         "fatload usb 0:2 $ramdiskaddr $ramdiskfile;"                    \
 858         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 859 "boot_usb_ext2 = "                                                      \
 860         "setenv bootargs root=/dev/ram rw "                             \
 861         "console=$consoledev,$baudrate $othbootargs "                   \
 862         "ramdisk_size=$ramdisk_size;"                                   \
 863         "usb start;"                                                    \
 864         "ext2load usb 0:4 $loadaddr $bootfile;"                         \
 865         "ext2load usb 0:4 $fdtaddr $fdtfile;"                           \
 866         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"                   \
 867         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 868 "boot_nor = "                                                           \
 869         "setenv bootargs root=/dev/$jffs2nor rw "                       \
 870         "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"  \
 871         "bootm $norbootaddr - $norfdtaddr\0 "                           \
 872 "boot_ram = "                                                           \
 873         "setenv bootargs root=/dev/ram rw "                             \
 874         "console=$consoledev,$baudrate $othbootargs "                   \
 875         "ramdisk_size=$ramdisk_size;"                                   \
 876         "tftp $ramdiskaddr $ramdiskfile;"                               \
 877         "tftp $loadaddr $bootfile;"                                     \
 878         "tftp $fdtaddr $fdtfile;"                                       \
 879         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
 880
 881 #endif
 882 #endif
 883
 884 #endif /* __CONFIG_H */