include/configs/UCP1020.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2013-2015 Arcturus Networks, Inc.
   4  *           http://www.arcturusnetworks.com/products/ucp1020/
   5  * based on include/configs/p1_p2_rdb_pc.h
   6  * original copyright follows:
   7  * Copyright 2009-2011 Freescale Semiconductor, Inc.
   8  */
   9
  10 /*
  11  * QorIQ uCP1020-xx boards configuration file
  12  */
  13 #ifndef __CONFIG_H
  14 #define __CONFIG_H
  15
  16 #define CONFIG_PCIE1    /* PCIE controller 1 (slot 1) */
  17 #define CONFIG_PCIE2    /* PCIE controller 2 (slot 2) */
  18 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
  19 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
  20 #define CONFIG_FSL_PCIE_RESET   /* need PCIe reset errata */
  21 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
  22
  23 #if defined(CONFIG_TARTGET_UCP1020T1)
  24
  25 #define CONFIG_UCP1020_REV_1_3
  26
  27 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
  28
  29 #define CONFIG_TSEC1
  30 #define CONFIG_TSEC3
  31 #define CONFIG_HAS_ETH0
  32 #define CONFIG_HAS_ETH1
  33 #define CONFIG_ETHADDR          00:19:D3:FF:FF:FF
  34 #define CONFIG_ETH1ADDR         00:19:D3:FF:FF:FE
  35 #define CONFIG_ETH2ADDR         00:19:D3:FF:FF:FD
  36 #define CONFIG_IPADDR           10.80.41.229
  37 #define CONFIG_SERVERIP         10.80.41.227
  38 #define CONFIG_NETMASK          255.255.252.0
  39 #define CONFIG_ETHPRIME         "eTSEC3"
  40
  41 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  42
  43 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  44
  45 #endif
  46
  47 #if defined(CONFIG_TARGET_UCP1020)
  48
  49 #define CONFIG_UCP1020
  50 #define CONFIG_UCP1020_REV_1_3
  51
  52 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
  53
  54 #define CONFIG_TSEC1
  55 #define CONFIG_TSEC2
  56 #define CONFIG_TSEC3
  57 #define CONFIG_HAS_ETH0
  58 #define CONFIG_HAS_ETH1
  59 #define CONFIG_HAS_ETH2
  60 #define CONFIG_ETHADDR          00:06:3B:FF:FF:FF
  61 #define CONFIG_ETH1ADDR         00:06:3B:FF:FF:FE
  62 #define CONFIG_ETH2ADDR         00:06:3B:FF:FF:FD
  63 #define CONFIG_IPADDR           192.168.1.81
  64 #define CONFIG_IPADDR1          192.168.1.82
  65 #define CONFIG_IPADDR2          192.168.1.83
  66 #define CONFIG_SERVERIP         192.168.1.80
  67 #define CONFIG_GATEWAYIP        102.168.1.1
  68 #define CONFIG_NETMASK          255.255.255.0
  69 #define CONFIG_ETHPRIME         "eTSEC1"
  70
  71 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  72
  73 #define CONFIG_SYS_L2_SIZE      (256 << 10)
  74
  75 #endif
  76
  77 #ifdef CONFIG_SDCARD
  78 #define CONFIG_RAMBOOT_SDCARD
  79 #define CONFIG_SYS_RAMBOOT
  80 #define CONFIG_SYS_EXTRA_ENV_RELOC
  81 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
  82 #endif
  83
  84 #ifdef CONFIG_SPIFLASH
  85 #define CONFIG_RAMBOOT_SPIFLASH
  86 #define CONFIG_SYS_RAMBOOT
  87 #define CONFIG_SYS_EXTRA_ENV_RELOC
  88 #define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
  89 #endif
  90
  91 #define CONFIG_SYS_TEXT_BASE_NOR        0xeff80000
  92
  93 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  94 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  95 #endif
  96
  97 #ifndef CONFIG_SYS_MONITOR_BASE
  98 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  99 #endif
 100
 101 #define CONFIG_ENV_OVERWRITE
 102
 103 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 104 #define CONFIG_LBA48
 105
 106 #define CONFIG_SYS_CLK_FREQ     66666666
 107 #define CONFIG_DDR_CLK_FREQ     66666666
 108
 109 #define CONFIG_HWCONFIG
 110
 111 /*
 112  * These can be toggled for performance analysis, otherwise use default.
 113  */
 114 #define CONFIG_L2_CACHE
 115 #define CONFIG_BTB
 116
 117 #define CONFIG_ENABLE_36BIT_PHYS
 118
 119 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 120 #define CONFIG_SYS_MEMTEST_END          0x1fffffff
 121
 122 #define CONFIG_SYS_CCSRBAR              0xffe00000
 123 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
 124
 125 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
 126        SPL code*/
 127 #ifdef CONFIG_SPL_BUILD
 128 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 129 #endif
 130
 131 /* DDR Setup */
 132 #define CONFIG_DDR_ECC_ENABLE
 133 #ifndef CONFIG_DDR_ECC_ENABLE
 134 #define CONFIG_SYS_DDR_RAW_TIMING
 135 #define CONFIG_DDR_SPD
 136 #endif
 137 #define CONFIG_SYS_SPD_BUS_NUM 1
 138 #undef CONFIG_FSL_DDR_INTERACTIVE
 139
 140 #define CONFIG_SYS_SDRAM_SIZE_LAW       LAW_SIZE_512M
 141 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
 142 #define CONFIG_SYS_SDRAM_SIZE           (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
 143 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 144 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 145
 146 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 147
 148 /* Default settings for DDR3 */
 149 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
 150 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
 151 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
 152 #define CONFIG_SYS_DDR_CS1_BNDS         0x0040007f
 153 #define CONFIG_SYS_DDR_CS1_CONFIG       0x80014302
 154 #define CONFIG_SYS_DDR_CS1_CONFIG_2     0x00000000
 155
 156 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 157 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
 158 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
 159 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
 160
 161 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
 162 #define CONFIG_SYS_DDR_WRLVL_CONTROL    0x8655A608
 163 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
 164 #define CONFIG_SYS_DDR_RCW_1            0x00000000
 165 #define CONFIG_SYS_DDR_RCW_2            0x00000000
 166 #ifdef CONFIG_DDR_ECC_ENABLE
 167 #define CONFIG_SYS_DDR_CONTROL          0xE70C0000      /* Type = DDR3 & ECC */
 168 #else
 169 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3 */
 170 #endif
 171 #define CONFIG_SYS_DDR_CONTROL_2        0x04401050
 172 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 173 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 174
 175 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 176 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
 177 #define CONFIG_SYS_DDR_TIMING_1         0x6f6B4846
 178 #define CONFIG_SYS_DDR_TIMING_2         0x0FA8C8CF
 179 #define CONFIG_SYS_DDR_CLK_CTRL         0x03000000
 180 #define CONFIG_SYS_DDR_MODE_1           0x40461520
 181 #define CONFIG_SYS_DDR_MODE_2           0x8000c000
 182 #define CONFIG_SYS_DDR_INTERVAL         0x0C300000
 183
 184 #undef CONFIG_CLOCKS_IN_MHZ
 185
 186 /*
 187  * Memory map
 188  *
 189  * 0x0000_0000 0x7fff_ffff      DDR             Up to 2GB cacheable
 190  * 0x8000_0000 0xdfff_ffff      PCI Express Mem 1G non-cacheable(PCIe * 2)
 191  * 0xec00_0000 0xefff_ffff      NOR flash       Up to 64M non-cacheable CS0/1
 192  * 0xf8f8_0000 0xf8ff_ffff      L2 SRAM         Up to 256K cacheable
 193  *   (early boot only)
 194  * 0xffc0_0000 0xffc3_ffff      PCI IO range    256k non-cacheable
 195  * 0xffd0_0000 0xffd0_3fff      L1 for stack    16K cacheable
 196  * 0xffe0_0000 0xffef_ffff      CCSR            1M non-cacheable
 197  */
 198
 199 /*
 200  * Local Bus Definitions
 201  */
 202 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* 64M */
 203 #define CONFIG_SYS_FLASH_BASE           0xec000000
 204
 205 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 206
 207 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 208         | BR_PS_16 | BR_V)
 209
 210 #define CONFIG_FLASH_OR_PRELIM          0xfc000ff7
 211
 212 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
 213 #define CONFIG_SYS_FLASH_QUIET_TEST
 214 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 215
 216 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 217
 218 #undef CONFIG_SYS_FLASH_CHECKSUM
 219 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 220 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 221
 222 #define CONFIG_FLASH_CFI_DRIVER
 223 #define CONFIG_SYS_FLASH_CFI
 224 #define CONFIG_SYS_FLASH_EMPTY_INFO
 225 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 226
 227 #define CONFIG_SYS_INIT_RAM_LOCK
 228 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000 /* stack in RAM */
 229 /* Initial L1 address */
 230 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 231 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 232 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 233 /* Size of used area in RAM */
 234 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 235
 236 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 237                                         GENERATED_GBL_DATA_SIZE)
 238 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 239
 240 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)/* Reserve 256 kB for Mon */
 241 #define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)/* Reserved for malloc */
 242
 243 #define CONFIG_SYS_PMC_BASE     0xff980000
 244 #define CONFIG_SYS_PMC_BASE_PHYS        CONFIG_SYS_PMC_BASE
 245 #define CONFIG_PMC_BR_PRELIM    (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
 246                                         BR_PS_8 | BR_V)
 247 #define CONFIG_PMC_OR_PRELIM    (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
 248                                  OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
 249                                  OR_GPCM_EAD)
 250
 251 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 252 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 253 #ifdef CONFIG_NAND_FSL_ELBC
 254 #define CONFIG_SYS_BR1_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
 255 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 256 #endif
 257
 258 /* Serial Port - controlled on board with jumper J8
 259  * open - index 2
 260  * shorted - index 1
 261  */
 262 #undef CONFIG_SERIAL_SOFTWARE_FIFO
 263 #define CONFIG_SYS_NS16550_SERIAL
 264 #define CONFIG_SYS_NS16550_REG_SIZE     1
 265 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 266 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
 267 #define CONFIG_NS16550_MIN_FUNCTIONS
 268 #endif
 269
 270 #define CONFIG_SYS_BAUDRATE_TABLE       \
 271         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 272
 273 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
 274 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
 275
 276 /* I2C */
 277 #define CONFIG_SYS_I2C
 278 #define CONFIG_SYS_I2C_FSL
 279 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 280 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 281 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 282 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 283 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 284 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 285 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x29} }
 286 #define CONFIG_SYS_SPD_BUS_NUM          1 /* For rom_loc and flash bank */
 287
 288 #define CONFIG_RTC_DS1337
 289 #define CONFIG_RTC_DS1337_NOOSC
 290 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 291 #define CONFIG_SYS_I2C_PCA9557_ADDR     0x18
 292 #define CONFIG_SYS_I2C_NCT72_ADDR       0x4C
 293 #define CONFIG_SYS_I2C_IDT6V49205B      0x69
 294
 295 /*
 296  * eSPI - Enhanced SPI
 297  */
 298 #define CONFIG_HARD_SPI
 299
 300 #define CONFIG_SF_DEFAULT_SPEED         10000000
 301 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 302
 303 #if defined(CONFIG_PCI)
 304 /*
 305  * General PCI
 306  * Memory space is mapped 1-1, but I/O space must start from 0.
 307  */
 308
 309 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 310 #define CONFIG_SYS_PCIE2_NAME           "PCIe SLOT CON9"
 311 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 312 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 313 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 314 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 315 #define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
 316 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 317 #define CONFIG_SYS_PCIE2_IO_PHYS        0xffc10000
 318 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 319
 320 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 321 #define CONFIG_SYS_PCIE1_NAME           "PCIe SLOT CON10"
 322 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 323 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 324 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 325 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 326 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 327 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 328 #define CONFIG_SYS_PCIE1_IO_PHYS        0xffc00000
 329 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 330
 331 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 332 #endif /* CONFIG_PCI */
 333
 334 /*
 335  * Environment
 336  */
 337 #ifdef CONFIG_ENV_FIT_UCBOOT
 338
 339 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x20000)
 340 #define CONFIG_ENV_SIZE         0x20000
 341 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 342
 343 #else
 344
 345 #define CONFIG_ENV_SPI_BUS      0
 346 #define CONFIG_ENV_SPI_CS       0
 347 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 348 #define CONFIG_ENV_SPI_MODE     0
 349
 350 #ifdef CONFIG_RAMBOOT_SPIFLASH
 351
 352 #define CONFIG_ENV_SIZE         0x3000          /* 12KB */
 353 #define CONFIG_ENV_OFFSET       0x2000          /* 8KB */
 354 #define CONFIG_ENV_SECT_SIZE    0x1000
 355
 356 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 357 /* Address and size of Redundant Environment Sector     */
 358 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 359 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 360 #endif
 361
 362 #elif defined(CONFIG_RAMBOOT_SDCARD)
 363 #define CONFIG_FSL_FIXED_MMC_LOCATION
 364 #define CONFIG_ENV_SIZE         0x2000
 365 #define CONFIG_SYS_MMC_ENV_DEV  0
 366
 367 #elif defined(CONFIG_SYS_RAMBOOT)
 368 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 369 #define CONFIG_ENV_SIZE         0x2000
 370
 371 #else
 372 #define CONFIG_ENV_BASE         (CONFIG_SYS_FLASH_BASE)
 373 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 374 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 375 #define CONFIG_ENV_ADDR         (CONFIG_ENV_BASE + 0xC0000)
 376 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
 377 /* Address and size of Redundant Environment Sector     */
 378 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
 379 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 380 #endif
 381
 382 #endif
 383
 384 #endif  /* CONFIG_ENV_FIT_UCBOOT */
 385
 386 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 387 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 388
 389 /*
 390  * USB
 391  */
 392 #define CONFIG_HAS_FSL_DR_USB
 393
 394 #if defined(CONFIG_HAS_FSL_DR_USB)
 395 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 396
 397 #ifdef CONFIG_USB_EHCI_HCD
 398 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 399 #define CONFIG_USB_EHCI_FSL
 400 #endif
 401 #endif
 402
 403 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 404
 405 #ifdef CONFIG_MMC
 406 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 407 #define CONFIG_MMC_SPI
 408 #endif
 409
 410 /* Misc Extra Settings */
 411 #undef CONFIG_WATCHDOG  /* watchdog disabled */
 412
 413 /*
 414  * Miscellaneous configurable options
 415  */
 416 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 417 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms tick */
 418
 419 /*
 420  * For booting Linux, the board info and command line data
 421  * have to be in the first 64 MB of memory, since this is
 422  * the maximum mapped by the Linux kernel during initialization.
 423  */
 424 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux*/
 425 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 426
 427 #if defined(CONFIG_CMD_KGDB)
 428 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 429 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 430 #endif
 431
 432 /*
 433  * Environment Configuration
 434  */
 435
 436 #if defined(CONFIG_TSEC_ENET)
 437
 438 #if defined(CONFIG_UCP1020_REV_1_2) || defined(CONFIG_UCP1020_REV_1_3)
 439 #else
 440 #error "UCP1020 module revision is not defined !!!"
 441 #endif
 442
 443 #define CONFIG_BOOTP_SERVERIP
 444
 445 #define CONFIG_MII              /* MII PHY management */
 446 #define CONFIG_TSEC1_NAME       "eTSEC1"
 447 #define CONFIG_TSEC2_NAME       "eTSEC2"
 448 #define CONFIG_TSEC3_NAME       "eTSEC3"
 449
 450 #define TSEC1_PHY_ADDR  4
 451 #define TSEC2_PHY_ADDR  0
 452 #define TSEC2_PHY_ADDR_SGMII    0x00
 453 #define TSEC3_PHY_ADDR  6
 454
 455 #define TSEC1_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 456 #define TSEC2_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 457 #define TSEC3_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
 458
 459 #define TSEC1_PHYIDX    0
 460 #define TSEC2_PHYIDX    0
 461 #define TSEC3_PHYIDX    0
 462
 463 #endif
 464
 465 #define CONFIG_HOSTNAME         "UCP1020"
 466 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 467 #define CONFIG_BOOTFILE         "uImage"
 468 #define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */
 469
 470 /* default location for tftp and bootm */
 471 #define CONFIG_LOADADDR         1000000
 472
 473 #if defined(CONFIG_DONGLE)
 474
 475 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 476 "bootcmd=run prog_spi_mbrbootcramfs\0"                                  \
 477 "bootfile=uImage\0"                                                     \
 478 "consoledev=ttyS0\0"                                                    \
 479 "cramfsfile=image.cramfs\0"                                             \
 480 "dtbaddr=0x00c00000\0"                                                  \
 481 "dtbfile=image.dtb\0"                                                   \
 482 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 483 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 484 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 485 "fileaddr=0x01000000\0"                                                 \
 486 "filesize=0x00080000\0"                                                 \
 487 "flashmbr=sf probe 0; "                                                 \
 488         "tftp $loadaddr $mbr; "                                         \
 489         "sf erase $mbr_offset +$filesize; "                             \
 490         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 491 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 492         "protect off $nor_recoveryaddr +$filesize; "                    \
 493         "erase $nor_recoveryaddr +$filesize; "                          \
 494         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 495         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 496 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 497         "protect off $nor_ubootaddr +$filesize; "                       \
 498         "erase $nor_ubootaddr +$filesize; "                             \
 499         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 500         "protect on $nor_ubootaddr +$filesize\0 "                       \
 501 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 502         "protect off $nor_workingaddr +$filesize; "                     \
 503         "erase $nor_workingaddr +$filesize; "                           \
 504         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 505         "protect on $nor_workingaddr +$filesize\0 "                     \
 506 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 507 "kerneladdr=0x01100000\0"                                               \
 508 "kernelfile=uImage\0"                                                   \
 509 "loadaddr=0x01000000\0"                                                 \
 510 "mbr=uCP1020d.mbr\0"                                                    \
 511 "mbr_offset=0x00000000\0"                                               \
 512 "mmbr=uCP1020Quiet.mbr\0"                                               \
 513 "mmcpart=0:2\0"                                                         \
 514 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 515         "mmc erase 1 1; "                                               \
 516         "mmc write $loadaddr 1 1\0"                                     \
 517 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; "                \
 518         "mmc erase 0x40 0x400; "                                        \
 519         "mmc write $loadaddr 0x40 0x400\0"                              \
 520 "netdev=eth0\0"                                                         \
 521 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 522 "nor_ubootaddr=0xEFF80000\0"                                            \
 523 "nor_workingaddr=0xECFA0000\0"                                          \
 524 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 525         " console=$consoledev,$baudrate $othbootargs; "                 \
 526         "run norloadrecovery; "                                         \
 527         "bootm $kerneladdr - $dtbaddr\0"                                \
 528 "norbootworking=setenv bootargs $workingbootargs"                       \
 529         " console=$consoledev,$baudrate $othbootargs; "                 \
 530         "run norloadworking; "                                          \
 531         "bootm $kerneladdr - $dtbaddr\0"                                \
 532 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 533         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 534         "cramfsload $dtbaddr $dtbfile; "                                \
 535         "cramfsload $kerneladdr $kernelfile\0"                          \
 536 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 537         "setenv cramfsaddr $nor_workingaddr; "                          \
 538         "cramfsload $dtbaddr $dtbfile; "                                \
 539         "cramfsload $kerneladdr $kernelfile\0"                          \
 540 "prog_spi_mbr=run spi__mbr\0"                                           \
 541 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0"       \
 542 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
 543         "run spi__cramfs\0"                                             \
 544 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 545         " console=$consoledev,$baudrate $othbootargs; "                 \
 546         "tftp $rootfsaddr $rootfsfile; "                                \
 547         "tftp $loadaddr $kernelfile; "                                  \
 548         "tftp $dtbaddr $dtbfile; "                                      \
 549         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 550 "ramdisk_size=120000\0"                                                 \
 551 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 552 "recoveryaddr=0x02F00000\0"                                             \
 553 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 554 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 555         "mw.l 0xffe0f008 0x00400000\0"                                  \
 556 "rootfsaddr=0x02F00000\0"                                               \
 557 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 558 "rootpath=/opt/nfsroot\0"                                               \
 559 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 560         "protect off 0xeC000000 +$filesize; "                           \
 561         "erase 0xEC000000 +$filesize; "                                 \
 562         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 563         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 564         "protect on 0xeC000000 +$filesize\0"                            \
 565 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
 566         "protect off 0xeFF80000 +$filesize; "                           \
 567         "erase 0xEFF80000 +$filesize; "                                 \
 568         "cp.b $loadaddr 0xEFF80000 $filesize; "                         \
 569         "cmp.b $loadaddr 0xEFF80000 $filesize; "                        \
 570         "protect on 0xeFF80000 +$filesize\0"                            \
 571 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; "                   \
 572         "sf probe 0; sf erase 0x8000 +$filesize; "                      \
 573         "sf write $loadaddr 0x8000 $filesize\0"                         \
 574 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; "             \
 575         "protect off 0xec0a0000 +$filesize; "                           \
 576         "erase 0xeC0A0000 +$filesize; "                                 \
 577         "cp.b $loadaddr 0xeC0A0000 $filesize; "                         \
 578         "protect on 0xec0a0000 +$filesize\0"                            \
 579 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 580         "sf probe 1; sf erase 0 +$filesize; "                           \
 581         "sf write $loadaddr 0 $filesize\0"                              \
 582 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
 583         "sf probe 0; sf erase 0 +$filesize; "                           \
 584         "sf write $loadaddr 0 $filesize\0"                              \
 585 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 586         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 587         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 588         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 589         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 590         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 591 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 592 "ubootaddr=0x01000000\0"                                                \
 593 "ubootfile=u-boot.bin\0"                                                \
 594 "ubootd=u-boot4dongle.bin\0"                                            \
 595 "upgrade=run flashworking\0"                                            \
 596 "usb_phy_type=ulpi\0 "                                                  \
 597 "workingaddr=0x02F00000\0"                                              \
 598 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 599
 600 #else
 601
 602 #if defined(CONFIG_UCP1020T1)
 603
 604 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 605 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0"  \
 606 "bootfile=uImage\0"                                                     \
 607 "consoledev=ttyS0\0"                                                    \
 608 "cramfsfile=image.cramfs\0"                                             \
 609 "dtbaddr=0x00c00000\0"                                                  \
 610 "dtbfile=image.dtb\0"                                                   \
 611 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 612 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 613 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 614 "fileaddr=0x01000000\0"                                                 \
 615 "filesize=0x00080000\0"                                                 \
 616 "flashmbr=sf probe 0; "                                                 \
 617         "tftp $loadaddr $mbr; "                                         \
 618         "sf erase $mbr_offset +$filesize; "                             \
 619         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 620 "flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
 621         "protect off $nor_recoveryaddr +$filesize; "                    \
 622         "erase $nor_recoveryaddr +$filesize; "                          \
 623         "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
 624         "protect on $nor_recoveryaddr +$filesize\0 "                    \
 625 "flashuboot=tftp $ubootaddr $ubootfile; "                               \
 626         "protect off $nor_ubootaddr +$filesize; "                       \
 627         "erase $nor_ubootaddr +$filesize; "                             \
 628         "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
 629         "protect on $nor_ubootaddr +$filesize\0 "                       \
 630 "flashworking=tftp $workingaddr $cramfsfile; "                          \
 631         "protect off $nor_workingaddr +$filesize; "                     \
 632         "erase $nor_workingaddr +$filesize; "                           \
 633         "cp.b $workingaddr $nor_workingaddr $filesize; "                \
 634         "protect on $nor_workingaddr +$filesize\0 "                     \
 635 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 636 "kerneladdr=0x01100000\0"                                               \
 637 "kernelfile=uImage\0"                                                   \
 638 "loadaddr=0x01000000\0"                                                 \
 639 "mbr=uCP1020.mbr\0"                                                     \
 640 "mbr_offset=0x00000000\0"                                               \
 641 "netdev=eth0\0"                                                         \
 642 "nor_recoveryaddr=0xEC0A0000\0"                                         \
 643 "nor_ubootaddr=0xEFF80000\0"                                            \
 644 "nor_workingaddr=0xECFA0000\0"                                          \
 645 "norbootrecovery=setenv bootargs $recoverybootargs"                     \
 646         " console=$consoledev,$baudrate $othbootargs; "                 \
 647         "run norloadrecovery; "                                         \
 648         "bootm $kerneladdr - $dtbaddr\0"                                \
 649 "norbootworking=setenv bootargs $workingbootargs"                       \
 650         " console=$consoledev,$baudrate $othbootargs; "                 \
 651         "run norloadworking; "                                          \
 652         "bootm $kerneladdr - $dtbaddr\0"                                \
 653 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
 654         "setenv cramfsaddr $nor_recoveryaddr; "                         \
 655         "cramfsload $dtbaddr $dtbfile; "                                \
 656         "cramfsload $kerneladdr $kernelfile\0"                          \
 657 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
 658         "setenv cramfsaddr $nor_workingaddr; "                          \
 659         "cramfsload $dtbaddr $dtbfile; "                                \
 660         "cramfsload $kerneladdr $kernelfile\0"                          \
 661 "othbootargs=quiet\0"                                                   \
 662 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 663         " console=$consoledev,$baudrate $othbootargs; "                 \
 664         "tftp $rootfsaddr $rootfsfile; "                                \
 665         "tftp $loadaddr $kernelfile; "                                  \
 666         "tftp $dtbaddr $dtbfile; "                                      \
 667         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 668 "ramdisk_size=120000\0"                                                 \
 669 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 670 "recoveryaddr=0x02F00000\0"                                             \
 671 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
 672 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 673         "mw.l 0xffe0f008 0x00400000\0"                                  \
 674 "rootfsaddr=0x02F00000\0"                                               \
 675 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 676 "rootpath=/opt/nfsroot\0"                                               \
 677 "silent=1\0"                                                            \
 678 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 679         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 680         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 681         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 682         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 683         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 684 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 685 "ubootaddr=0x01000000\0"                                                \
 686 "ubootfile=u-boot.bin\0"                                                \
 687 "upgrade=run flashworking\0"                                            \
 688 "workingaddr=0x02F00000\0"                                              \
 689 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
 690
 691 #else /* For Arcturus Modules */
 692
 693 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 694 "bootcmd=run norkernel\0"                                               \
 695 "bootfile=uImage\0"                                                     \
 696 "consoledev=ttyS0\0"                                                    \
 697 "dtbaddr=0x00c00000\0"                                                  \
 698 "dtbfile=image.dtb\0"                                                   \
 699 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
 700 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
 701 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
 702 "fileaddr=0x01000000\0"                                                 \
 703 "filesize=0x00080000\0"                                                 \
 704 "flashmbr=sf probe 0; "                                                 \
 705         "tftp $loadaddr $mbr; "                                         \
 706         "sf erase $mbr_offset +$filesize; "                             \
 707         "sf write $loadaddr $mbr_offset $filesize\0"                    \
 708 "flashuboot=tftp $loadaddr $ubootfile; "                                \
 709         "protect off $nor_ubootaddr0 +$filesize; "                      \
 710         "erase $nor_ubootaddr0 +$filesize; "                            \
 711         "cp.b $loadaddr $nor_ubootaddr0 $filesize; "                    \
 712         "protect on $nor_ubootaddr0 +$filesize; "                       \
 713         "protect off $nor_ubootaddr1 +$filesize; "                      \
 714         "erase $nor_ubootaddr1 +$filesize; "                            \
 715         "cp.b $loadaddr $nor_ubootaddr1 $filesize; "                    \
 716         "protect on $nor_ubootaddr1 +$filesize\0 "                      \
 717 "format0=protect off $part0base +$part0size; "                          \
 718         "erase $part0base +$part0size\0"                                \
 719 "format1=protect off $part1base +$part1size; "                          \
 720         "erase $part1base +$part1size\0"                                \
 721 "format2=protect off $part2base +$part2size; "                          \
 722         "erase $part2base +$part2size\0"                                \
 723 "format3=protect off $part3base +$part3size; "                          \
 724         "erase $part3base +$part3size\0"                                \
 725 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
 726 "kerneladdr=0x01100000\0"                                               \
 727 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"                 \
 728 "kernelfile=uImage\0"                                                   \
 729 "loadaddr=0x01000000\0"                                                 \
 730 "mbr=uCP1020.mbr\0"                                                     \
 731 "mbr_offset=0x00000000\0"                                               \
 732 "netdev=eth0\0"                                                         \
 733 "nor_ubootaddr0=0xEC000000\0"                                           \
 734 "nor_ubootaddr1=0xEFF80000\0"                                           \
 735 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
 736         "run norkernelload; "                                           \
 737         "bootm $kerneladdr - $dtbaddr\0"                                \
 738 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; "                       \
 739         "setenv cramfsaddr $part0base; "                                \
 740         "cramfsload $dtbaddr $dtbfile; "                                \
 741         "cramfsload $kerneladdr $kernelfile\0"                          \
 742 "part0base=0xEC100000\0"                                                \
 743 "part0size=0x00700000\0"                                                \
 744 "part1base=0xEC800000\0"                                                \
 745 "part1size=0x02000000\0"                                                \
 746 "part2base=0xEE800000\0"                                                \
 747 "part2size=0x00800000\0"                                                \
 748 "part3base=0xEF000000\0"                                                \
 749 "part3size=0x00F80000\0"                                                \
 750 "partENVbase=0xEC080000\0"                                              \
 751 "partENVsize=0x00080000\0"                                              \
 752 "program0=tftp part0-000000.bin; "                                      \
 753         "protect off $part0base +$filesize; "                           \
 754         "erase $part0base +$filesize; "                                 \
 755         "cp.b $loadaddr $part0base $filesize; "                         \
 756         "echo Verifying...; "                                           \
 757         "cmp.b $loadaddr $part0base $filesize\0"                        \
 758 "program1=tftp part1-000000.bin; "                                      \
 759         "protect off $part1base +$filesize; "                           \
 760         "erase $part1base +$filesize; "                                 \
 761         "cp.b $loadaddr $part1base $filesize; "                         \
 762         "echo Verifying...; "                                           \
 763         "cmp.b $loadaddr $part1base $filesize\0"                        \
 764 "program2=tftp part2-000000.bin; "                                      \
 765         "protect off $part2base +$filesize; "                           \
 766         "erase $part2base +$filesize; "                                 \
 767         "cp.b $loadaddr $part2base $filesize; "                         \
 768         "echo Verifying...; "                                           \
 769         "cmp.b $loadaddr $part2base $filesize\0"                        \
 770 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
 771         "  console=$consoledev,$baudrate $othbootargs; "                \
 772         "tftp $rootfsaddr $rootfsfile; "                                \
 773         "tftp $loadaddr $kernelfile; "                                  \
 774         "tftp $dtbaddr $dtbfile; "                                      \
 775         "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
 776 "ramdisk_size=120000\0"                                                 \
 777 "ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
 778 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
 779         "mw.l 0xffe0f008 0x00400000\0"                                  \
 780 "rootfsaddr=0x02F00000\0"                                               \
 781 "rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
 782 "rootpath=/opt/nfsroot\0"                                               \
 783 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
 784         "sf probe 0; sf erase 0 +$filesize; "                           \
 785         "sf write $loadaddr 0 $filesize\0"                              \
 786 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; "                 \
 787         "protect off 0xeC000000 +$filesize; "                           \
 788         "erase 0xEC000000 +$filesize; "                                 \
 789         "cp.b $loadaddr 0xEC000000 $filesize; "                         \
 790         "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
 791         "protect on 0xeC000000 +$filesize\0"                            \
 792 "tftpflash=tftpboot $loadaddr $uboot; "                                 \
 793         "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 794         "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
 795         "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
 796         "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
 797         "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
 798 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
 799 "ubootfile=u-boot.bin\0"                                                \
 800 "upgrade=run flashuboot\0"                                              \
 801 "usb_phy_type=ulpi\0 "                                                  \
 802 "boot_nfs= "                                                            \
 803         "setenv bootargs root=/dev/nfs rw "                             \
 804         "nfsroot=$serverip:$rootpath "                                  \
 805         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 806         "console=$consoledev,$baudrate $othbootargs;"                   \
 807         "tftp $loadaddr $bootfile;"                                     \
 808         "tftp $fdtaddr $fdtfile;"                                       \
 809         "bootm $loadaddr - $fdtaddr\0"                                  \
 810 "boot_hd = "                                                            \
 811         "setenv bootargs root=/dev/$bdev rw rootdelay=30 "              \
 812         "console=$consoledev,$baudrate $othbootargs;"                   \
 813         "usb start;"                                                    \
 814         "ext2load usb 0:1 $loadaddr /boot/$bootfile;"                   \
 815         "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"                     \
 816         "bootm $loadaddr - $fdtaddr\0"                                  \
 817 "boot_usb_fat = "                                                       \
 818         "setenv bootargs root=/dev/ram rw "                             \
 819         "console=$consoledev,$baudrate $othbootargs "                   \
 820         "ramdisk_size=$ramdisk_size;"                                   \
 821         "usb start;"                                                    \
 822         "fatload usb 0:2 $loadaddr $bootfile;"                          \
 823         "fatload usb 0:2 $fdtaddr $fdtfile;"                            \
 824         "fatload usb 0:2 $ramdiskaddr $ramdiskfile;"                    \
 825         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 826 "boot_usb_ext2 = "                                                      \
 827         "setenv bootargs root=/dev/ram rw "                             \
 828         "console=$consoledev,$baudrate $othbootargs "                   \
 829         "ramdisk_size=$ramdisk_size;"                                   \
 830         "usb start;"                                                    \
 831         "ext2load usb 0:4 $loadaddr $bootfile;"                         \
 832         "ext2load usb 0:4 $fdtaddr $fdtfile;"                           \
 833         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"                   \
 834         "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
 835 "boot_nor = "                                                           \
 836         "setenv bootargs root=/dev/$jffs2nor rw "                       \
 837         "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"  \
 838         "bootm $norbootaddr - $norfdtaddr\0 "                           \
 839 "boot_ram = "                                                           \
 840         "setenv bootargs root=/dev/ram rw "                             \
 841         "console=$consoledev,$baudrate $othbootargs "                   \
 842         "ramdisk_size=$ramdisk_size;"                                   \
 843         "tftp $ramdiskaddr $ramdiskfile;"                               \
 844         "tftp $loadaddr $bootfile;"                                     \
 845         "tftp $fdtaddr $fdtfile;"                                       \
 846         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"
 847
 848 #endif
 849 #endif
 850
 851 #endif /* __CONFIG_H */