include/configs/T4240RDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020-2021 NXP
   5  */
   6
   7 /*
   8  * T4240 RDB board configuration file
   9  */
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #include <linux/stringify.h>
  14
  15 #define CONFIG_FSL_SATA_V2
  16 #define CONFIG_PCIE4
  17
  18 #define CONFIG_ICS307_REFCLK_HZ         25000000  /* ICS307 ref clk freq */
  19
  20 #ifdef CONFIG_RAMBOOT_PBL
  21 #define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t4rdb/t4_pbi.cfg
  22 #ifndef CONFIG_SDCARD
  23 #define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
  24 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
  25 #else
  26 #define CONFIG_SPL_FLUSH_IMAGE
  27 #define CONFIG_SPL_PAD_TO               0x40000
  28 #define CONFIG_SPL_MAX_SIZE             0x28000
  29 #define RESET_VECTOR_OFFSET             0x27FFC
  30 #define BOOT_PAGE_OFFSET                0x27000
  31
  32 #ifdef  CONFIG_SDCARD
  33 #define CONFIG_RESET_VECTOR_ADDRESS     0x200FFC
  34 #define CONFIG_SYS_MMC_U_BOOT_SIZE      (768 << 10)
  35 #define CONFIG_SYS_MMC_U_BOOT_DST       0x00200000
  36 #define CONFIG_SYS_MMC_U_BOOT_START     0x00200000
  37 #define CONFIG_SYS_MMC_U_BOOT_OFFS      (260 << 10)
  38 #ifndef CONFIG_SPL_BUILD
  39 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  40 #endif
  41 #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t4rdb/t4_sd_rcw.cfg
  42 #endif
  43
  44 #ifdef CONFIG_SPL_BUILD
  45 #define CONFIG_SPL_SKIP_RELOCATE
  46 #define CONFIG_SPL_COMMON_INIT_DDR
  47 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  48 #endif
  49
  50 #endif
  51 #endif /* CONFIG_RAMBOOT_PBL */
  52
  53 #define CONFIG_DDR_ECC
  54
  55 /* High Level Configuration Options */
  56 #define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
  57
  58 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  59 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  60 #endif
  61
  62 #define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
  63 #define CONFIG_SYS_NUM_CPC              CONFIG_SYS_NUM_DDR_CTLRS
  64 #define CONFIG_PCIE1                    /* PCIE controller 1 */
  65 #define CONFIG_PCIE2                    /* PCIE controller 2 */
  66 #define CONFIG_PCIE3                    /* PCIE controller 3 */
  67 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
  68
  69 /*
  70  * These can be toggled for performance analysis, otherwise use default.
  71  */
  72 #define CONFIG_SYS_CACHE_STASHING
  73 #define CONFIG_BTB                      /* toggle branch predition */
  74 #ifdef CONFIG_DDR_ECC
  75 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  76 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  77 #endif
  78
  79 #define CONFIG_ENABLE_36BIT_PHYS
  80
  81 /*
  82  *  Config the L3 Cache as L3 SRAM
  83  */
  84 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
  85 #define CONFIG_SYS_L3_SIZE              (512 << 10)
  86 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
  87 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
  88 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
  89 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
  90 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
  91
  92 #define CONFIG_SYS_DCSRBAR              0xf0000000
  93 #define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
  94
  95 /*
  96  * DDR Setup
  97  */
  98 #define CONFIG_VERY_BIG_RAM
  99 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 100 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 101
 102 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 103 #define CONFIG_CHIP_SELECTS_PER_CTRL    4
 104
 105 #define CONFIG_DDR_SPD
 106
 107 /*
 108  * IFC Definitions
 109  */
 110 #define CONFIG_SYS_FLASH_BASE   0xe0000000
 111 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 112
 113 #ifdef CONFIG_SPL_BUILD
 114 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SPL_TEXT_BASE
 115 #else
 116 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 117 #endif
 118
 119 #define CONFIG_HWCONFIG
 120
 121 /* define to use L1 as initial stack */
 122 #define CONFIG_L1_INIT_RAM
 123 #define CONFIG_SYS_INIT_RAM_LOCK
 124 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000      /* Initial L1 address */
 125 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 126 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 127 /* The assembler doesn't like typecast */
 128 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 129         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 130           CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 131 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 132
 133 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 134                                         GENERATED_GBL_DATA_SIZE)
 135 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 136
 137 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 138 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 139
 140 /* Serial Port - controlled on board with jumper J8
 141  * open - index 2
 142  * shorted - index 1
 143  */
 144 #define CONFIG_SYS_NS16550_SERIAL
 145 #define CONFIG_SYS_NS16550_REG_SIZE     1
 146 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 147
 148 #define CONFIG_SYS_BAUDRATE_TABLE       \
 149         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 150
 151 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 152 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 153 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 154 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 155
 156 /* I2C */
 157 #if !CONFIG_IS_ENABLED(DM_I2C)
 158 #define CONFIG_SYS_I2C_LEGACY
 159 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 160 #define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
 161 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 162 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x118100
 163 #else
 164 #define CONFIG_I2C_SET_DEFAULT_BUS_NUM
 165 #define CONFIG_I2C_DEFAULT_BUS_NUMBER   0
 166 #endif
 167
 168 #define CONFIG_SYS_I2C_FSL
 169
 170 /*
 171  * General PCI
 172  * Memory space is mapped 1-1, but I/O space must start from 0.
 173  */
 174
 175 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 176 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 177 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 178 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 179 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 180
 181 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 182 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 183 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 184 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 185 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 186
 187 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 188 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xc0000000
 189 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc40000000ull
 190 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 191 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 192
 193 /* controller 4, Base address 203000 */
 194 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 195 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc60000000ull
 196 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 197
 198 #ifdef CONFIG_PCI
 199 #if !defined(CONFIG_DM_PCI)
 200 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 201 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 202 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 203 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 204 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 205 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 206 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 207 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 208 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 209 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 210 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
 211 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 212 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 213 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 214 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x20000000      /* 512M */
 215 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 216 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 217 #define CONFIG_PCI_INDIRECT_BRIDGE
 218 #endif
 219
 220 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 221 #endif  /* CONFIG_PCI */
 222
 223 /* SATA */
 224 #ifdef CONFIG_FSL_SATA_V2
 225 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 226 #define CONFIG_SATA1
 227 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 228 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 229 #define CONFIG_SATA2
 230 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 231 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 232
 233 #define CONFIG_LBA48
 234 #endif
 235
 236 #ifdef CONFIG_FMAN_ENET
 237 #define CONFIG_ETHPRIME         "FM1@DTSEC1"
 238 #endif
 239
 240 /*
 241  * Environment
 242  */
 243 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 244 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 245
 246 /*
 247  * Miscellaneous configurable options
 248  */
 249 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 250
 251 /*
 252  * For booting Linux, the board info and command line data
 253  * have to be in the first 64 MB of memory, since this is
 254  * the maximum mapped by the Linux kernel during initialization.
 255  */
 256 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 257 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 258
 259 #ifdef CONFIG_CMD_KGDB
 260 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 261 #endif
 262
 263 /*
 264  * Environment Configuration
 265  */
 266 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 267 #define CONFIG_BOOTFILE         "uImage"
 268 #define CONFIG_UBOOTPATH        "u-boot.bin"    /* U-Boot image on TFTP server*/
 269
 270 /* default location for tftp and bootm */
 271 #define CONFIG_LOADADDR         1000000
 272
 273 #define CONFIG_HVBOOT                                   \
 274         "setenv bootargs config-addr=0x60000000; "      \
 275         "bootm 0x01000000 - 0x00f00000"
 276
 277 #define CONFIG_SYS_CLK_FREQ     66666666
 278 #define CONFIG_DDR_CLK_FREQ     133333333
 279
 280 #ifndef __ASSEMBLY__
 281 unsigned long get_board_sys_clk(void);
 282 unsigned long get_board_ddr_clk(void);
 283 #endif
 284
 285 /*
 286  * DDR Setup
 287  */
 288 #define CONFIG_SYS_SPD_BUS_NUM  0
 289 #define SPD_EEPROM_ADDRESS1     0x52
 290 #define SPD_EEPROM_ADDRESS2     0x54
 291 #define SPD_EEPROM_ADDRESS3     0x56
 292 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1     /* for p3041/p5010 */
 293 #define CONFIG_SYS_SDRAM_SIZE   4096    /* for fixed parameter use */
 294
 295 /*
 296  * IFC Definitions
 297  */
 298 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 299 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
 300                                 + 0x8000000) | \
 301                                 CSPR_PORT_SIZE_16 | \
 302                                 CSPR_MSEL_NOR | \
 303                                 CSPR_V)
 304 #define CONFIG_SYS_NOR1_CSPR_EXT        (0xf)
 305 #define CONFIG_SYS_NOR1_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 306                                 CSPR_PORT_SIZE_16 | \
 307                                 CSPR_MSEL_NOR | \
 308                                 CSPR_V)
 309 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 310 /* NOR Flash Timing Params */
 311 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 312
 313 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 314                                 FTIM0_NOR_TEADC(0x5) | \
 315                                 FTIM0_NOR_TEAHC(0x5))
 316 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 317                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 318                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 319 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 320                                 FTIM2_NOR_TCH(0x4) | \
 321                                 FTIM2_NOR_TWPH(0x0E) | \
 322                                 FTIM2_NOR_TWP(0x1c))
 323 #define CONFIG_SYS_NOR_FTIM3    0x0
 324
 325 #define CONFIG_SYS_FLASH_QUIET_TEST
 326 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 327
 328 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
 329 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 330 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 331 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 332
 333 #define CONFIG_SYS_FLASH_EMPTY_INFO
 334 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS \
 335                                         + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 336
 337 /* NAND Flash on IFC */
 338 #define CONFIG_NAND_FSL_IFC
 339 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 340 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 341 #define CONFIG_SYS_NAND_BASE            0xff800000
 342 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 343
 344 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 345 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 346                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 347                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 348                                 | CSPR_V)
 349 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 350
 351 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 352                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 353                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 354                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */ \
 355                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
 356                                 | CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
 357                                 | CSOR_NAND_PB(128))    /*Page Per Block = 128*/
 358
 359 #define CONFIG_SYS_NAND_ONFI_DETECTION
 360
 361 /* ONFI NAND Flash mode0 Timing Params */
 362 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 363                                         FTIM0_NAND_TWP(0x18)   | \
 364                                         FTIM0_NAND_TWCHT(0x07) | \
 365                                         FTIM0_NAND_TWH(0x0a))
 366 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 367                                         FTIM1_NAND_TWBE(0x39)  | \
 368                                         FTIM1_NAND_TRR(0x0e)   | \
 369                                         FTIM1_NAND_TRP(0x18))
 370 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f) | \
 371                                         FTIM2_NAND_TREH(0x0a) | \
 372                                         FTIM2_NAND_TWHRE(0x1e))
 373 #define CONFIG_SYS_NAND_FTIM3           0x0
 374
 375 #define CONFIG_SYS_NAND_DDR_LAW         11
 376 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 377 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 378
 379 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 380
 381 #if defined(CONFIG_MTD_RAW_NAND)
 382 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 383 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 384 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 385 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 386 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 387 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 388 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 389 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 390 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 391 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR
 392 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 393 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 394 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 395 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 396 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 397 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 398 #else
 399 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 400 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 401 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 402 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 403 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 404 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 405 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 406 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 407 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 408 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 409 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 410 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 411 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 412 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 413 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 414 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 415 #endif
 416 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 417 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR1_CSPR
 418 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 419 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 420 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 421 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 422 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 423 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 424
 425 /* CPLD on IFC */
 426 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 427 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 428 #define CONFIG_SYS_CSPR3_EXT    (0xf)
 429 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
 430                                 | CSPR_PORT_SIZE_8 \
 431                                 | CSPR_MSEL_GPCM \
 432                                 | CSPR_V)
 433
 434 #define CONFIG_SYS_AMASK3       IFC_AMASK(64 * 1024)
 435 #define CONFIG_SYS_CSOR3        0x0
 436
 437 /* CPLD Timing parameters for IFC CS3 */
 438 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 439                                         FTIM0_GPCM_TEADC(0x0e) | \
 440                                         FTIM0_GPCM_TEAHC(0x0e))
 441 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 442                                         FTIM1_GPCM_TRAD(0x1f))
 443 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 444                                         FTIM2_GPCM_TCH(0x8) | \
 445                                         FTIM2_GPCM_TWP(0x1f))
 446 #define CONFIG_SYS_CS3_FTIM3            0x0
 447
 448 #if defined(CONFIG_RAMBOOT_PBL)
 449 #define CONFIG_SYS_RAMBOOT
 450 #endif
 451
 452 /* I2C */
 453 #define CONFIG_SYS_FSL_I2C_SPEED        100000  /* I2C speed */
 454 #define CONFIG_SYS_FSL_I2C2_SPEED       100000  /* I2C2 speed */
 455 #define I2C_MUX_PCA_ADDR_PRI            0x77 /* I2C bus multiplexer,primary */
 456 #define I2C_MUX_PCA_ADDR_SEC            0x76 /* I2C bus multiplexer,secondary */
 457
 458 #define I2C_MUX_CH_DEFAULT      0x8
 459 #define I2C_MUX_CH_VOL_MONITOR  0xa
 460 #define I2C_MUX_CH_VSC3316_FS   0xc
 461 #define I2C_MUX_CH_VSC3316_BS   0xd
 462
 463 /* Voltage monitor on channel 2*/
 464 #define I2C_VOL_MONITOR_ADDR            0x40
 465 #define I2C_VOL_MONITOR_BUS_V_OFFSET    0x2
 466 #define I2C_VOL_MONITOR_BUS_V_OVF       0x1
 467 #define I2C_VOL_MONITOR_BUS_V_SHIFT     3
 468
 469 #define CONFIG_VID_FLS_ENV              "t4240rdb_vdd_mv"
 470 #ifndef CONFIG_SPL_BUILD
 471 #define CONFIG_VID
 472 #endif
 473 #define CONFIG_VOL_MONITOR_IR36021_SET
 474 #define CONFIG_VOL_MONITOR_IR36021_READ
 475 /* The lowest and highest voltage allowed for T4240RDB */
 476 #define VDD_MV_MIN                      819
 477 #define VDD_MV_MAX                      1212
 478
 479 /*
 480  * eSPI - Enhanced SPI
 481  */
 482
 483 /* Qman/Bman */
 484 #ifndef CONFIG_NOBQFMAN
 485 #define CONFIG_SYS_BMAN_NUM_PORTALS     50
 486 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 487 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 488 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 489 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 490 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 491 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 492 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 493 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 494                                         CONFIG_SYS_BMAN_CENA_SIZE)
 495 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 496 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 497 #define CONFIG_SYS_QMAN_NUM_PORTALS     50
 498 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 499 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 500 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 501 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 502 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 503 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 504 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 505 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 506                                         CONFIG_SYS_QMAN_CENA_SIZE)
 507 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 508 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 509
 510 #define CONFIG_SYS_DPAA_FMAN
 511 #define CONFIG_SYS_DPAA_PME
 512 #define CONFIG_SYS_PMAN
 513 #define CONFIG_SYS_DPAA_DCE
 514 #define CONFIG_SYS_DPAA_RMAN
 515 #define CONFIG_SYS_INTERLAKEN
 516
 517 /* Default address of microcode for the Linux Fman driver */
 518 #if defined(CONFIG_SPIFLASH)
 519 /*
 520  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 521  * env, so we got 0x110000.
 522  */
 523 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
 524 #elif defined(CONFIG_SDCARD)
 525 /*
 526  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 527  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 528  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 529  */
 530 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
 531 #elif defined(CONFIG_MTD_RAW_NAND)
 532 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 533 #else
 534 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
 535 #endif
 536 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 537 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 538 #endif /* CONFIG_NOBQFMAN */
 539
 540 #ifdef CONFIG_SYS_DPAA_FMAN
 541 #define CONFIG_CORTINA_FW_ADDR          0xefe00000
 542 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 543 #define SGMII_PHY_ADDR1 0x0
 544 #define SGMII_PHY_ADDR2 0x1
 545 #define SGMII_PHY_ADDR3 0x2
 546 #define SGMII_PHY_ADDR4 0x3
 547 #define SGMII_PHY_ADDR5 0x4
 548 #define SGMII_PHY_ADDR6 0x5
 549 #define SGMII_PHY_ADDR7 0x6
 550 #define SGMII_PHY_ADDR8 0x7
 551 #define FM1_10GEC1_PHY_ADDR     0x10
 552 #define FM1_10GEC2_PHY_ADDR     0x11
 553 #define FM2_10GEC1_PHY_ADDR     0x12
 554 #define FM2_10GEC2_PHY_ADDR     0x13
 555 #define CORTINA_PHY_ADDR1       FM1_10GEC1_PHY_ADDR
 556 #define CORTINA_PHY_ADDR2       FM1_10GEC2_PHY_ADDR
 557 #define CORTINA_PHY_ADDR3       FM2_10GEC1_PHY_ADDR
 558 #define CORTINA_PHY_ADDR4       FM2_10GEC2_PHY_ADDR
 559 #endif
 560
 561 /* SATA */
 562 #ifdef CONFIG_FSL_SATA_V2
 563 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 564 #define CONFIG_SATA1
 565 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 566 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 567 #define CONFIG_SATA2
 568 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 569 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 570
 571 #define CONFIG_LBA48
 572 #endif
 573
 574 #ifdef CONFIG_FMAN_ENET
 575 #define CONFIG_ETHPRIME         "FM1@DTSEC1"
 576 #endif
 577
 578 /*
 579 * USB
 580 */
 581 #define CONFIG_USB_EHCI_FSL
 582 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 583 #define CONFIG_HAS_FSL_DR_USB
 584
 585 #ifdef CONFIG_MMC
 586 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 587 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 588 #endif
 589
 590
 591 #define __USB_PHY_TYPE  utmi
 592
 593 /*
 594  * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
 595  * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
 596  * interleaving. It can be cacheline, page, bank, superbank.
 597  * See doc/README.fsl-ddr for details.
 598  */
 599 #ifdef CONFIG_ARCH_T4240
 600 #define CTRL_INTLV_PREFERED 3way_4KB
 601 #else
 602 #define CTRL_INTLV_PREFERED cacheline
 603 #endif
 604
 605 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 606         "hwconfig=fsl_ddr:"                                     \
 607         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 608         "bank_intlv=auto;"                                      \
 609         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 610         "netdev=eth0\0"                                         \
 611         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 612         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 613         "tftpflash=tftpboot $loadaddr $uboot && "               \
 614         "protect off $ubootaddr +$filesize && "                 \
 615         "erase $ubootaddr +$filesize && "                       \
 616         "cp.b $loadaddr $ubootaddr $filesize && "               \
 617         "protect on $ubootaddr +$filesize && "                  \
 618         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 619         "consoledev=ttyS0\0"                                    \
 620         "ramdiskaddr=2000000\0"                                 \
 621         "ramdiskfile=t4240rdb/ramdisk.uboot\0"                  \
 622         "fdtaddr=1e00000\0"                                     \
 623         "fdtfile=t4240rdb/t4240rdb.dtb\0"                       \
 624         "bdev=sda3\0"
 625
 626 #define CONFIG_HVBOOT                                   \
 627         "setenv bootargs config-addr=0x60000000; "      \
 628         "bootm 0x01000000 - 0x00f00000"
 629
 630 #define CONFIG_LINUX                                    \
 631         "setenv bootargs root=/dev/ram rw "             \
 632         "console=$consoledev,$baudrate $othbootargs;"   \
 633         "setenv ramdiskaddr 0x02000000;"                \
 634         "setenv fdtaddr 0x00c00000;"                    \
 635         "setenv loadaddr 0x1000000;"                    \
 636         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 637
 638 #define CONFIG_HDBOOT                                   \
 639         "setenv bootargs root=/dev/$bdev rw "           \
 640         "console=$consoledev,$baudrate $othbootargs;"   \
 641         "tftp $loadaddr $bootfile;"                     \
 642         "tftp $fdtaddr $fdtfile;"                       \
 643         "bootm $loadaddr - $fdtaddr"
 644
 645 #define CONFIG_NFSBOOTCOMMAND                   \
 646         "setenv bootargs root=/dev/nfs rw "     \
 647         "nfsroot=$serverip:$rootpath "          \
 648         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 649         "console=$consoledev,$baudrate $othbootargs;"   \
 650         "tftp $loadaddr $bootfile;"             \
 651         "tftp $fdtaddr $fdtfile;"               \
 652         "bootm $loadaddr - $fdtaddr"
 653
 654 #define CONFIG_RAMBOOTCOMMAND                           \
 655         "setenv bootargs root=/dev/ram rw "             \
 656         "console=$consoledev,$baudrate $othbootargs;"   \
 657         "tftp $ramdiskaddr $ramdiskfile;"               \
 658         "tftp $loadaddr $bootfile;"                     \
 659         "tftp $fdtaddr $fdtfile;"                       \
 660         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 661
 662 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 663
 664 #include <asm/fsl_secure_boot.h>
 665
 666 #endif  /* __CONFIG_H */