include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  * Copyright 2020-2021 NXP
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #include <linux/stringify.h>
  15
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17
  18 /* High Level Configuration Options */
  19
  20 #define CFG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
  21
  22 #ifdef CONFIG_RAMBOOT_PBL
  23 #define RESET_VECTOR_OFFSET             0x27FFC
  24 #define BOOT_PAGE_OFFSET                0x27000
  25
  26 #ifdef CONFIG_MTD_RAW_NAND
  27 #define CFG_SYS_NAND_U_BOOT_SIZE        (768 << 10)
  28 #define CFG_SYS_NAND_U_BOOT_DST 0x00200000
  29 #define CFG_SYS_NAND_U_BOOT_START       0x00200000
  30 #endif
  31
  32 #ifdef CONFIG_SPIFLASH
  33 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  34 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  35 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  36 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  37 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  38 #endif
  39
  40 #ifdef CONFIG_SDCARD
  41 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  42 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  43 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  44 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  45 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  46 #endif
  47
  48 #endif /* CONFIG_RAMBOOT_PBL */
  49
  50 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  51 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  52 /* Set 1M boot space */
  53 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_TEXT_BASE & 0xfff00000)
  54 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  55                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  56 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  57 #endif
  58
  59 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  60 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  61 #endif
  62
  63 /*
  64  * These can be toggled for performance analysis, otherwise use default.
  65  */
  66 #ifdef CONFIG_DDR_ECC
  67 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  68 #endif
  69
  70 /*
  71  * Config the L3 Cache as L3 SRAM
  72  */
  73 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
  74 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
  75
  76 #define CONFIG_SYS_DCSRBAR      0xf0000000
  77 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
  78
  79 /*
  80  * DDR Setup
  81  */
  82 #define CONFIG_VERY_BIG_RAM
  83 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  84 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  85 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
  86 #define SPD_EEPROM_ADDRESS1     0x51
  87 #define SPD_EEPROM_ADDRESS2     0x52
  88 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
  89 #define CTRL_INTLV_PREFERED     cacheline
  90
  91 /*
  92  * IFC Definitions
  93  */
  94 #define CONFIG_SYS_FLASH_BASE           0xe8000000
  95 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
  96 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
  97 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
  98                                 CSPR_PORT_SIZE_16 | \
  99                                 CSPR_MSEL_NOR | \
 100                                 CSPR_V)
 101 #define CFG_SYS_NOR_AMASK       IFC_AMASK(128*1024*1024)
 102
 103 /* NOR Flash Timing Params */
 104 #define CFG_SYS_NOR_CSOR        CSOR_NAND_TRHZ_80
 105
 106 #define CFG_SYS_NOR_FTIM0       (FTIM0_NOR_TACSE(0x4) | \
 107                                 FTIM0_NOR_TEADC(0x5) | \
 108                                 FTIM0_NOR_TEAHC(0x5))
 109 #define CFG_SYS_NOR_FTIM1       (FTIM1_NOR_TACO(0x35) | \
 110                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 111                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 112 #define CFG_SYS_NOR_FTIM2       (FTIM2_NOR_TCS(0x4) | \
 113                                 FTIM2_NOR_TCH(0x4) | \
 114                                 FTIM2_NOR_TWPH(0x0E) | \
 115                                 FTIM2_NOR_TWP(0x1c))
 116 #define CFG_SYS_NOR_FTIM3       0x0
 117
 118 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 119
 120 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 121
 122 /* CPLD on IFC */
 123 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 124 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 125 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 126 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 127                                 | CSPR_PORT_SIZE_8 \
 128                                 | CSPR_MSEL_GPCM \
 129                                 | CSPR_V)
 130 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 131 #define CONFIG_SYS_CSOR2        0x0
 132
 133 /* CPLD Timing parameters for IFC CS2 */
 134 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 135                                         FTIM0_GPCM_TEADC(0x0e) | \
 136                                         FTIM0_GPCM_TEAHC(0x0e))
 137 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 138                                         FTIM1_GPCM_TRAD(0x1f))
 139 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 140                                         FTIM2_GPCM_TCH(0x8) | \
 141                                         FTIM2_GPCM_TWP(0x1f))
 142 #define CONFIG_SYS_CS2_FTIM3            0x0
 143
 144 /* NAND Flash on IFC */
 145 #define CFG_SYS_NAND_BASE               0xff800000
 146 #define CFG_SYS_NAND_BASE_PHYS  (0xf00000000ull | CFG_SYS_NAND_BASE)
 147
 148 #define CFG_SYS_NAND_CSPR_EXT   (0xf)
 149 #define CFG_SYS_NAND_CSPR       (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
 150                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 151                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 152                                 | CSPR_V)
 153 #define CFG_SYS_NAND_AMASK      IFC_AMASK(64*1024)
 154
 155 #define CFG_SYS_NAND_CSOR       (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 156                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 157                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 158                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 159                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 160                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 161                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 162
 163 /* ONFI NAND Flash mode0 Timing Params */
 164 #define CFG_SYS_NAND_FTIM0              (FTIM0_NAND_TCCST(0x07) | \
 165                                         FTIM0_NAND_TWP(0x18)    | \
 166                                         FTIM0_NAND_TWCHT(0x07)  | \
 167                                         FTIM0_NAND_TWH(0x0a))
 168 #define CFG_SYS_NAND_FTIM1              (FTIM1_NAND_TADLE(0x32) | \
 169                                         FTIM1_NAND_TWBE(0x39)   | \
 170                                         FTIM1_NAND_TRR(0x0e)    | \
 171                                         FTIM1_NAND_TRP(0x18))
 172 #define CFG_SYS_NAND_FTIM2              (FTIM2_NAND_TRAD(0x0f)  | \
 173                                         FTIM2_NAND_TREH(0x0a)   | \
 174                                         FTIM2_NAND_TWHRE(0x1e))
 175 #define CFG_SYS_NAND_FTIM3              0x0
 176
 177 #define CFG_SYS_NAND_BASE_LIST  { CFG_SYS_NAND_BASE }
 178
 179 #if defined(CONFIG_MTD_RAW_NAND)
 180 #define CONFIG_SYS_CSPR0_EXT            CFG_SYS_NAND_CSPR_EXT
 181 #define CONFIG_SYS_CSPR0                CFG_SYS_NAND_CSPR
 182 #define CONFIG_SYS_AMASK0               CFG_SYS_NAND_AMASK
 183 #define CONFIG_SYS_CSOR0                CFG_SYS_NAND_CSOR
 184 #define CONFIG_SYS_CS0_FTIM0            CFG_SYS_NAND_FTIM0
 185 #define CONFIG_SYS_CS0_FTIM1            CFG_SYS_NAND_FTIM1
 186 #define CONFIG_SYS_CS0_FTIM2            CFG_SYS_NAND_FTIM2
 187 #define CONFIG_SYS_CS0_FTIM3            CFG_SYS_NAND_FTIM3
 188 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 189 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 190 #define CONFIG_SYS_AMASK1               CFG_SYS_NOR_AMASK
 191 #define CONFIG_SYS_CSOR1                CFG_SYS_NOR_CSOR
 192 #define CONFIG_SYS_CS1_FTIM0            CFG_SYS_NOR_FTIM0
 193 #define CONFIG_SYS_CS1_FTIM1            CFG_SYS_NOR_FTIM1
 194 #define CONFIG_SYS_CS1_FTIM2            CFG_SYS_NOR_FTIM2
 195 #define CONFIG_SYS_CS1_FTIM3            CFG_SYS_NOR_FTIM3
 196 #else
 197 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 198 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 199 #define CONFIG_SYS_AMASK0               CFG_SYS_NOR_AMASK
 200 #define CONFIG_SYS_CSOR0                CFG_SYS_NOR_CSOR
 201 #define CONFIG_SYS_CS0_FTIM0            CFG_SYS_NOR_FTIM0
 202 #define CONFIG_SYS_CS0_FTIM1            CFG_SYS_NOR_FTIM1
 203 #define CONFIG_SYS_CS0_FTIM2            CFG_SYS_NOR_FTIM2
 204 #define CONFIG_SYS_CS0_FTIM3            CFG_SYS_NOR_FTIM3
 205 #define CONFIG_SYS_CSPR1_EXT            CFG_SYS_NAND_CSPR_EXT
 206 #define CONFIG_SYS_CSPR1                CFG_SYS_NAND_CSPR
 207 #define CONFIG_SYS_AMASK1               CFG_SYS_NAND_AMASK
 208 #define CONFIG_SYS_CSOR1                CFG_SYS_NAND_CSOR
 209 #define CONFIG_SYS_CS1_FTIM0            CFG_SYS_NAND_FTIM0
 210 #define CONFIG_SYS_CS1_FTIM1            CFG_SYS_NAND_FTIM1
 211 #define CONFIG_SYS_CS1_FTIM2            CFG_SYS_NAND_FTIM2
 212 #define CONFIG_SYS_CS1_FTIM3            CFG_SYS_NAND_FTIM3
 213 #endif
 214
 215 #define CONFIG_HWCONFIG
 216
 217 /* define to use L1 as initial stack */
 218 #define CONFIG_L1_INIT_RAM
 219 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 220 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 221 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 222 /* The assembler doesn't like typecast */
 223 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 224                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 225                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 226 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 227 #define CONFIG_SYS_INIT_SP_OFFSET       (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 228
 229 /*
 230  * Serial Port
 231  */
 232 #define CFG_SYS_NS16550_CLK             (get_bus_freq(0)/2)
 233 #define CONFIG_SYS_BAUDRATE_TABLE       \
 234         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 235 #define CFG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 236 #define CFG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 237 #define CFG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 238 #define CFG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 239
 240 /*
 241  * I2C
 242  */
 243
 244 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 245 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 246 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 247 #define I2C_MUX_CH_DEFAULT      0x8
 248
 249 #define I2C_MUX_CH_VOL_MONITOR  0xa
 250
 251 /* The lowest and highest voltage allowed for T208xRDB */
 252 #define VDD_MV_MIN                      819
 253 #define VDD_MV_MAX                      1212
 254
 255 /*
 256  * RapidIO
 257  */
 258 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 259 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 260 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 261 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 262 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 263 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 264 /*
 265  * for slave u-boot IMAGE instored in master memory space,
 266  * PHYS must be aligned based on the SIZE
 267  */
 268 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 269 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 270 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 271 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 272 /*
 273  * for slave UCODE and ENV instored in master memory space,
 274  * PHYS must be aligned based on the SIZE
 275  */
 276 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 277 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 278 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 279
 280 /* slave core release by master*/
 281 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 282 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 283
 284 /*
 285  * SRIO_PCIE_BOOT - SLAVE
 286  */
 287 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 288 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 289 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 290                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 291 #endif
 292
 293 /*
 294  * eSPI - Enhanced SPI
 295  */
 296
 297 /*
 298  * General PCI
 299  * Memory space is mapped 1-1, but I/O space must start from 0.
 300  */
 301 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 302 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 303 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 304 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 305 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 306
 307 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 308 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 309 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 310 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 311 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 312
 313 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 314 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 315 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 316
 317 /* controller 4, Base address 203000 */
 318 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 319 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 320
 321 /* Qman/Bman */
 322 #ifndef CONFIG_NOBQFMAN
 323 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 324 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 325 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 326 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 327 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 328 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 329 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 330 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 331 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 332                                         CONFIG_SYS_BMAN_CENA_SIZE)
 333 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 334 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 335 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 336 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 337 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 338 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 339 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 340 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 341 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 342                                         CONFIG_SYS_QMAN_CENA_SIZE)
 343 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 344 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 345
 346 #define CONFIG_SYS_DPAA_FMAN
 347 #define CONFIG_SYS_DPAA_PME
 348 #define CONFIG_SYS_PMAN
 349 #define CONFIG_SYS_DPAA_DCE
 350 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 351 #endif /* CONFIG_NOBQFMAN */
 352
 353 #ifdef CONFIG_SYS_DPAA_FMAN
 354 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 355 #define RGMII_PHY2_ADDR         0x02
 356 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 357 #define CORTINA_PHY_ADDR2       0x0d
 358 /* Aquantia AQ1202 10G Base-T used by board revisions up to C */
 359 #define FM1_10GEC3_PHY_ADDR     0x00
 360 #define FM1_10GEC4_PHY_ADDR     0x01
 361 /* Aquantia AQR113C 10G Base-T used by board revisions D and up */
 362 #define AQR113C_PHY_ADDR1       0x00
 363 #define AQR113C_PHY_ADDR2       0x08
 364 #endif
 365
 366 /*
 367  * USB
 368  */
 369
 370 /*
 371  * SDHC
 372  */
 373 #ifdef CONFIG_MMC
 374 #define CFG_SYS_FSL_ESDHC_ADDR  CFG_SYS_MPC85xx_ESDHC_ADDR
 375 #endif
 376
 377 /*
 378  * Dynamic MTD Partition support with mtdparts
 379  */
 380
 381 /*
 382  * Environment
 383  */
 384
 385 /*
 386  * Miscellaneous configurable options
 387  */
 388
 389 /*
 390  * For booting Linux, the board info and command line data
 391  * have to be in the first 64 MB of memory, since this is
 392  * the maximum mapped by the Linux kernel during initialization.
 393  */
 394 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 395
 396 /*
 397  * Environment Configuration
 398  */
 399 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 400 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 401
 402 #define __USB_PHY_TYPE          utmi
 403
 404 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 405         "hwconfig=fsl_ddr:"                                     \
 406         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 407         "bank_intlv=auto;"                                      \
 408         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 409         "netdev=eth0\0"                                         \
 410         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 411         "ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \
 412         "tftpflash=tftpboot $loadaddr $uboot && "               \
 413         "protect off $ubootaddr +$filesize && "                 \
 414         "erase $ubootaddr +$filesize && "                       \
 415         "cp.b $loadaddr $ubootaddr $filesize && "               \
 416         "protect on $ubootaddr +$filesize && "                  \
 417         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 418         "consoledev=ttyS0\0"                                    \
 419         "ramdiskaddr=2000000\0"                                 \
 420         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 421         "fdtaddr=1e00000\0"                                     \
 422         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 423         "bdev=sda3\0"
 424
 425 /*
 426  * For emulation this causes u-boot to jump to the start of the
 427  * proof point app code automatically
 428  */
 429 #define PROOF_POINTS                            \
 430         "setenv bootargs root=/dev/$bdev rw "           \
 431         "console=$consoledev,$baudrate $othbootargs;"   \
 432         "cpu 1 release 0x29000000 - - -;"               \
 433         "cpu 2 release 0x29000000 - - -;"               \
 434         "cpu 3 release 0x29000000 - - -;"               \
 435         "cpu 4 release 0x29000000 - - -;"               \
 436         "cpu 5 release 0x29000000 - - -;"               \
 437         "cpu 6 release 0x29000000 - - -;"               \
 438         "cpu 7 release 0x29000000 - - -;"               \
 439         "go 0x29000000"
 440
 441 #define HVBOOT                          \
 442         "setenv bootargs config-addr=0x60000000; "      \
 443         "bootm 0x01000000 - 0x00f00000"
 444
 445 #define ALU                             \
 446         "setenv bootargs root=/dev/$bdev rw "           \
 447         "console=$consoledev,$baudrate $othbootargs;"   \
 448         "cpu 1 release 0x01000000 - - -;"               \
 449         "cpu 2 release 0x01000000 - - -;"               \
 450         "cpu 3 release 0x01000000 - - -;"               \
 451         "cpu 4 release 0x01000000 - - -;"               \
 452         "cpu 5 release 0x01000000 - - -;"               \
 453         "cpu 6 release 0x01000000 - - -;"               \
 454         "cpu 7 release 0x01000000 - - -;"               \
 455         "go 0x01000000"
 456
 457 #include <asm/fsl_secure_boot.h>
 458
 459 #endif  /* __T2080RDB_H */