include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  */
   5
   6 /*
   7  * T2080 RDB/PCIe board configuration file
   8  */
   9
  10 #ifndef __T2080RDB_H
  11 #define __T2080RDB_H
  12
  13 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  14 #define CONFIG_FSL_SATA_V2
  15
  16 /* High Level Configuration Options */
  17 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  18 #define CONFIG_ENABLE_36BIT_PHYS
  19
  20 #ifdef CONFIG_PHYS_64BIT
  21 #define CONFIG_ADDR_MAP 1
  22 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
  23 #endif
  24
  25 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  26 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  27 #define CONFIG_ENV_OVERWRITE
  28
  29 #ifdef CONFIG_RAMBOOT_PBL
  30 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
  31
  32 #define CONFIG_SPL_FLUSH_IMAGE
  33 #define CONFIG_SPL_PAD_TO               0x40000
  34 #define CONFIG_SPL_MAX_SIZE             0x28000
  35 #define RESET_VECTOR_OFFSET             0x27FFC
  36 #define BOOT_PAGE_OFFSET                0x27000
  37 #ifdef CONFIG_SPL_BUILD
  38 #define CONFIG_SPL_SKIP_RELOCATE
  39 #define CONFIG_SPL_COMMON_INIT_DDR
  40 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  41 #endif
  42
  43 #ifdef CONFIG_NAND
  44 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  45 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  46 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  47 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  48 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
  49 #endif
  50
  51 #ifdef CONFIG_SPIFLASH
  52 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  53 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  54 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  55 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  56 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  57 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  58 #ifndef CONFIG_SPL_BUILD
  59 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  60 #endif
  61 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
  62 #endif
  63
  64 #ifdef CONFIG_SDCARD
  65 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  66 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  67 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  68 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  69 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  70 #ifndef CONFIG_SPL_BUILD
  71 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  72 #endif
  73 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
  74 #endif
  75
  76 #endif /* CONFIG_RAMBOOT_PBL */
  77
  78 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  79 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  80 /* Set 1M boot space */
  81 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  82 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  83                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  84 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  85 #endif
  86
  87 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  88 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  89 #endif
  90
  91 /*
  92  * These can be toggled for performance analysis, otherwise use default.
  93  */
  94 #define CONFIG_SYS_CACHE_STASHING
  95 #define CONFIG_BTB              /* toggle branch predition */
  96 #define CONFIG_DDR_ECC
  97 #ifdef CONFIG_DDR_ECC
  98 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  99 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 100 #endif
 101
 102 #define CONFIG_SYS_MEMTEST_START        0x00200000 /* memtest works on */
 103 #define CONFIG_SYS_MEMTEST_END          0x00400000
 104
 105 #if defined(CONFIG_SPIFLASH)
 106 #define CONFIG_ENV_SIZE         0x2000     /* 8KB */
 107 #define CONFIG_ENV_OFFSET       0x100000   /* 1MB */
 108 #define CONFIG_ENV_SECT_SIZE    0x10000
 109 #elif defined(CONFIG_SDCARD)
 110 #define CONFIG_SYS_MMC_ENV_DEV  0
 111 #define CONFIG_ENV_SIZE         0x2000
 112 #define CONFIG_ENV_OFFSET       (512 * 0x800)
 113 #elif defined(CONFIG_NAND)
 114 #define CONFIG_ENV_SIZE         0x2000
 115 #define CONFIG_ENV_OFFSET       (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
 116 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 117 #define CONFIG_ENV_ADDR         0xffe20000
 118 #define CONFIG_ENV_SIZE         0x2000
 119 #elif defined(CONFIG_ENV_IS_NOWHERE)
 120 #define CONFIG_ENV_SIZE         0x2000
 121 #else
 122 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 123 #define CONFIG_ENV_SIZE         0x2000
 124 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 125 #endif
 126
 127 #ifndef __ASSEMBLY__
 128 unsigned long get_board_sys_clk(void);
 129 unsigned long get_board_ddr_clk(void);
 130 #endif
 131
 132 #define CONFIG_SYS_CLK_FREQ     66660000
 133 #define CONFIG_DDR_CLK_FREQ     133330000
 134
 135 /*
 136  * Config the L3 Cache as L3 SRAM
 137  */
 138 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 139 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 140 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 141 #ifdef CONFIG_RAMBOOT_PBL
 142 #define CONFIG_ENV_ADDR                 (CONFIG_SPL_GD_ADDR + 4 * 1024)
 143 #endif
 144 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 145 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 146 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 147
 148 #define CONFIG_SYS_DCSRBAR      0xf0000000
 149 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 150
 151 /* EEPROM */
 152 #define CONFIG_ID_EEPROM
 153 #define CONFIG_SYS_I2C_EEPROM_NXID
 154 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 155 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 156 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 157
 158 /*
 159  * DDR Setup
 160  */
 161 #define CONFIG_VERY_BIG_RAM
 162 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 163 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 164 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 165 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 166 #define CONFIG_DDR_SPD
 167 #define CONFIG_SYS_SPD_BUS_NUM  0
 168 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 169 #define SPD_EEPROM_ADDRESS1     0x51
 170 #define SPD_EEPROM_ADDRESS2     0x52
 171 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 172 #define CTRL_INTLV_PREFERED     cacheline
 173
 174 /*
 175  * IFC Definitions
 176  */
 177 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 178 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 179 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 180 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 181                                 CSPR_PORT_SIZE_16 | \
 182                                 CSPR_MSEL_NOR | \
 183                                 CSPR_V)
 184 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 185
 186 /* NOR Flash Timing Params */
 187 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 188
 189 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 190                                 FTIM0_NOR_TEADC(0x5) | \
 191                                 FTIM0_NOR_TEAHC(0x5))
 192 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 193                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 194                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 195 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 196                                 FTIM2_NOR_TCH(0x4) | \
 197                                 FTIM2_NOR_TWPH(0x0E) | \
 198                                 FTIM2_NOR_TWP(0x1c))
 199 #define CONFIG_SYS_NOR_FTIM3    0x0
 200
 201 #define CONFIG_SYS_FLASH_QUIET_TEST
 202 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 203
 204 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 205 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 206 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 207 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 208 #define CONFIG_SYS_FLASH_EMPTY_INFO
 209 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 210
 211 /* CPLD on IFC */
 212 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 213 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 214 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 215 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 216                                 | CSPR_PORT_SIZE_8 \
 217                                 | CSPR_MSEL_GPCM \
 218                                 | CSPR_V)
 219 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 220 #define CONFIG_SYS_CSOR2        0x0
 221
 222 /* CPLD Timing parameters for IFC CS2 */
 223 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 224                                         FTIM0_GPCM_TEADC(0x0e) | \
 225                                         FTIM0_GPCM_TEAHC(0x0e))
 226 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 227                                         FTIM1_GPCM_TRAD(0x1f))
 228 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 229                                         FTIM2_GPCM_TCH(0x8) | \
 230                                         FTIM2_GPCM_TWP(0x1f))
 231 #define CONFIG_SYS_CS2_FTIM3            0x0
 232
 233 /* NAND Flash on IFC */
 234 #define CONFIG_NAND_FSL_IFC
 235 #define CONFIG_SYS_NAND_BASE            0xff800000
 236 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 237
 238 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 239 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 240                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 241                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 242                                 | CSPR_V)
 243 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 244
 245 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 246                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 247                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 248                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 249                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 250                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 251                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 252
 253 #define CONFIG_SYS_NAND_ONFI_DETECTION
 254
 255 /* ONFI NAND Flash mode0 Timing Params */
 256 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 257                                         FTIM0_NAND_TWP(0x18)    | \
 258                                         FTIM0_NAND_TWCHT(0x07)  | \
 259                                         FTIM0_NAND_TWH(0x0a))
 260 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 261                                         FTIM1_NAND_TWBE(0x39)   | \
 262                                         FTIM1_NAND_TRR(0x0e)    | \
 263                                         FTIM1_NAND_TRP(0x18))
 264 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 265                                         FTIM2_NAND_TREH(0x0a)   | \
 266                                         FTIM2_NAND_TWHRE(0x1e))
 267 #define CONFIG_SYS_NAND_FTIM3           0x0
 268
 269 #define CONFIG_SYS_NAND_DDR_LAW         11
 270 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 271 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 272 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 273
 274 #if defined(CONFIG_NAND)
 275 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 276 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 277 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 278 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 279 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 280 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 281 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 282 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 283 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 284 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 285 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 286 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 287 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 288 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 289 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 290 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 291 #else
 292 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 293 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 294 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 295 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 296 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 297 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 298 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 299 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 300 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 301 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 302 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 303 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 304 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 305 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 306 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 307 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 308 #endif
 309
 310 #if defined(CONFIG_RAMBOOT_PBL)
 311 #define CONFIG_SYS_RAMBOOT
 312 #endif
 313
 314 #ifdef CONFIG_SPL_BUILD
 315 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 316 #else
 317 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 318 #endif
 319
 320 #define CONFIG_HWCONFIG
 321
 322 /* define to use L1 as initial stack */
 323 #define CONFIG_L1_INIT_RAM
 324 #define CONFIG_SYS_INIT_RAM_LOCK
 325 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 326 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 327 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 328 /* The assembler doesn't like typecast */
 329 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 330                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 331                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 332 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 333 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 334                                                 GENERATED_GBL_DATA_SIZE)
 335 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 336 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 337 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 338
 339 /*
 340  * Serial Port
 341  */
 342 #define CONFIG_SYS_NS16550_SERIAL
 343 #define CONFIG_SYS_NS16550_REG_SIZE     1
 344 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 345 #define CONFIG_SYS_BAUDRATE_TABLE       \
 346         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 347 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 348 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 349 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 350 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 351
 352 /*
 353  * I2C
 354  */
 355 #define CONFIG_SYS_I2C
 356 #define CONFIG_SYS_I2C_FSL
 357 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 358 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 359 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 360 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 361 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 362 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 363 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 364 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 365 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 366 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 367 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 368 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 369 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 370 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 371 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 372 #define I2C_MUX_CH_DEFAULT      0x8
 373
 374 #define I2C_MUX_CH_VOL_MONITOR  0xa
 375
 376 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 377 #ifndef CONFIG_SPL_BUILD
 378 #define CONFIG_VID
 379 #endif
 380 #define CONFIG_VOL_MONITOR_IR36021_SET
 381 #define CONFIG_VOL_MONITOR_IR36021_READ
 382 /* The lowest and highest voltage allowed for T208xRDB */
 383 #define VDD_MV_MIN                      819
 384 #define VDD_MV_MAX                      1212
 385
 386 /*
 387  * RapidIO
 388  */
 389 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 390 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 391 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 392 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 393 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 394 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 395 /*
 396  * for slave u-boot IMAGE instored in master memory space,
 397  * PHYS must be aligned based on the SIZE
 398  */
 399 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 400 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 401 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 402 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 403 /*
 404  * for slave UCODE and ENV instored in master memory space,
 405  * PHYS must be aligned based on the SIZE
 406  */
 407 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 408 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 409 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 410
 411 /* slave core release by master*/
 412 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 413 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 414
 415 /*
 416  * SRIO_PCIE_BOOT - SLAVE
 417  */
 418 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 419 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 420 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 421                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 422 #endif
 423
 424 /*
 425  * eSPI - Enhanced SPI
 426  */
 427
 428 /*
 429  * General PCI
 430  * Memory space is mapped 1-1, but I/O space must start from 0.
 431  */
 432 #define CONFIG_PCIE1            /* PCIE controller 1 */
 433 #define CONFIG_PCIE2            /* PCIE controller 2 */
 434 #define CONFIG_PCIE3            /* PCIE controller 3 */
 435 #define CONFIG_PCIE4            /* PCIE controller 4 */
 436 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 437 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 438 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 439 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 440 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 441 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 442 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 443 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 444 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 445 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 446 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 447
 448 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 449 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 450 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 451 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 452 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 453 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 454 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 455 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 456 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 457
 458 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 459 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 460 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 461 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 462 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 463 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 464 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 465 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 466 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 467
 468 /* controller 4, Base address 203000 */
 469 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 470 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 471 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 472 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 473 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 474 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 475 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 476
 477 #ifdef CONFIG_PCI
 478 #define CONFIG_PCI_INDIRECT_BRIDGE
 479 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 480 #endif
 481
 482 /* Qman/Bman */
 483 #ifndef CONFIG_NOBQFMAN
 484 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 485 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 486 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 487 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 488 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 489 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 490 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 491 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 492 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 493                                         CONFIG_SYS_BMAN_CENA_SIZE)
 494 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 495 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 496 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 497 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 498 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 499 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 500 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 501 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 502 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 503 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 504 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 505                                         CONFIG_SYS_QMAN_CENA_SIZE)
 506 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 507 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 508
 509 #define CONFIG_SYS_DPAA_FMAN
 510 #define CONFIG_SYS_DPAA_PME
 511 #define CONFIG_SYS_PMAN
 512 #define CONFIG_SYS_DPAA_DCE
 513 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 514 #define CONFIG_SYS_INTERLAKEN
 515
 516 /* Default address of microcode for the Linux Fman driver */
 517 #if defined(CONFIG_SPIFLASH)
 518 /*
 519  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 520  * env, so we got 0x110000.
 521  */
 522 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
 523 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 524 #define CONFIG_CORTINA_FW_ADDR          0x120000
 525
 526 #elif defined(CONFIG_SDCARD)
 527 /*
 528  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 529  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 530  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 531  */
 532 #define CONFIG_SYS_CORTINA_FW_IN_MMC
 533 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 534 #define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)
 535
 536 #elif defined(CONFIG_NAND)
 537 #define CONFIG_SYS_CORTINA_FW_IN_NAND
 538 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 539 #define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 540 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 541 /*
 542  * Slave has no ucode locally, it can fetch this from remote. When implementing
 543  * in two corenet boards, slave's ucode could be stored in master's memory
 544  * space, the address can be mapped from slave TLB->slave LAW->
 545  * slave SRIO or PCIE outbound window->master inbound window->
 546  * master LAW->the ucode address in master's memory space.
 547  */
 548 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE
 549 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 550 #define CONFIG_CORTINA_FW_ADDR          0xFFE10000
 551 #else
 552 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 553 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 554 #define CONFIG_CORTINA_FW_ADDR          0xEFE00000
 555 #endif
 556 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 557 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 558 #endif /* CONFIG_NOBQFMAN */
 559
 560 #ifdef CONFIG_SYS_DPAA_FMAN
 561 #define CONFIG_PHY_CORTINA
 562 #define CONFIG_PHY_REALTEK
 563 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 564 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 565 #define RGMII_PHY2_ADDR         0x02
 566 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 567 #define CORTINA_PHY_ADDR2       0x0d
 568 #define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
 569 #define FM1_10GEC4_PHY_ADDR     0x01
 570 #endif
 571
 572 #ifdef CONFIG_FMAN_ENET
 573 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 574 #endif
 575
 576 /*
 577  * SATA
 578  */
 579 #ifdef CONFIG_FSL_SATA_V2
 580 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 581 #define CONFIG_SATA1
 582 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 583 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 584 #define CONFIG_SATA2
 585 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 586 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 587 #define CONFIG_LBA48
 588 #endif
 589
 590 /*
 591  * USB
 592  */
 593 #ifdef CONFIG_USB_EHCI_HCD
 594 #define CONFIG_USB_EHCI_FSL
 595 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 596 #define CONFIG_HAS_FSL_DR_USB
 597 #endif
 598
 599 /*
 600  * SDHC
 601  */
 602 #ifdef CONFIG_MMC
 603 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 604 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 605 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 606 #endif
 607
 608 /*
 609  * Dynamic MTD Partition support with mtdparts
 610  */
 611
 612 /*
 613  * Environment
 614  */
 615
 616 /*
 617  * Miscellaneous configurable options
 618  */
 619 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 620
 621 /*
 622  * For booting Linux, the board info and command line data
 623  * have to be in the first 64 MB of memory, since this is
 624  * the maximum mapped by the Linux kernel during initialization.
 625  */
 626 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 627 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 628
 629 #ifdef CONFIG_CMD_KGDB
 630 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 631 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 632 #endif
 633
 634 /*
 635  * Environment Configuration
 636  */
 637 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 638 #define CONFIG_BOOTFILE  "uImage"
 639 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 640
 641 /* default location for tftp and bootm */
 642 #define CONFIG_LOADADDR         1000000
 643 #define __USB_PHY_TYPE          utmi
 644
 645 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 646         "hwconfig=fsl_ddr:"                                     \
 647         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 648         "bank_intlv=auto;"                                      \
 649         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 650         "netdev=eth0\0"                                         \
 651         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 652         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 653         "tftpflash=tftpboot $loadaddr $uboot && "               \
 654         "protect off $ubootaddr +$filesize && "                 \
 655         "erase $ubootaddr +$filesize && "                       \
 656         "cp.b $loadaddr $ubootaddr $filesize && "               \
 657         "protect on $ubootaddr +$filesize && "                  \
 658         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 659         "consoledev=ttyS0\0"                                    \
 660         "ramdiskaddr=2000000\0"                                 \
 661         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 662         "fdtaddr=1e00000\0"                                     \
 663         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 664         "bdev=sda3\0"
 665
 666 /*
 667  * For emulation this causes u-boot to jump to the start of the
 668  * proof point app code automatically
 669  */
 670 #define CONFIG_PROOF_POINTS                             \
 671         "setenv bootargs root=/dev/$bdev rw "           \
 672         "console=$consoledev,$baudrate $othbootargs;"   \
 673         "cpu 1 release 0x29000000 - - -;"               \
 674         "cpu 2 release 0x29000000 - - -;"               \
 675         "cpu 3 release 0x29000000 - - -;"               \
 676         "cpu 4 release 0x29000000 - - -;"               \
 677         "cpu 5 release 0x29000000 - - -;"               \
 678         "cpu 6 release 0x29000000 - - -;"               \
 679         "cpu 7 release 0x29000000 - - -;"               \
 680         "go 0x29000000"
 681
 682 #define CONFIG_HVBOOT                           \
 683         "setenv bootargs config-addr=0x60000000; "      \
 684         "bootm 0x01000000 - 0x00f00000"
 685
 686 #define CONFIG_ALU                              \
 687         "setenv bootargs root=/dev/$bdev rw "           \
 688         "console=$consoledev,$baudrate $othbootargs;"   \
 689         "cpu 1 release 0x01000000 - - -;"               \
 690         "cpu 2 release 0x01000000 - - -;"               \
 691         "cpu 3 release 0x01000000 - - -;"               \
 692         "cpu 4 release 0x01000000 - - -;"               \
 693         "cpu 5 release 0x01000000 - - -;"               \
 694         "cpu 6 release 0x01000000 - - -;"               \
 695         "cpu 7 release 0x01000000 - - -;"               \
 696         "go 0x01000000"
 697
 698 #define CONFIG_LINUX                            \
 699         "setenv bootargs root=/dev/ram rw "             \
 700         "console=$consoledev,$baudrate $othbootargs;"   \
 701         "setenv ramdiskaddr 0x02000000;"                \
 702         "setenv fdtaddr 0x00c00000;"                    \
 703         "setenv loadaddr 0x1000000;"                    \
 704         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 705
 706 #define CONFIG_HDBOOT                                   \
 707         "setenv bootargs root=/dev/$bdev rw "           \
 708         "console=$consoledev,$baudrate $othbootargs;"   \
 709         "tftp $loadaddr $bootfile;"                     \
 710         "tftp $fdtaddr $fdtfile;"                       \
 711         "bootm $loadaddr - $fdtaddr"
 712
 713 #define CONFIG_NFSBOOTCOMMAND                   \
 714         "setenv bootargs root=/dev/nfs rw "     \
 715         "nfsroot=$serverip:$rootpath "          \
 716         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 717         "console=$consoledev,$baudrate $othbootargs;"   \
 718         "tftp $loadaddr $bootfile;"             \
 719         "tftp $fdtaddr $fdtfile;"               \
 720         "bootm $loadaddr - $fdtaddr"
 721
 722 #define CONFIG_RAMBOOTCOMMAND                           \
 723         "setenv bootargs root=/dev/ram rw "             \
 724         "console=$consoledev,$baudrate $othbootargs;"   \
 725         "tftp $ramdiskaddr $ramdiskfile;"               \
 726         "tftp $loadaddr $bootfile;"                     \
 727         "tftp $fdtaddr $fdtfile;"                       \
 728         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 729
 730 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 731
 732 #include <asm/fsl_secure_boot.h>
 733
 734 #endif  /* __T2080RDB_H */