include/configs/T208xRDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2014 Freescale Semiconductor, Inc.
   4  */
   5
   6 /*
   7  * T2080 RDB/PCIe board configuration file
   8  */
   9
  10 #ifndef __T2080RDB_H
  11 #define __T2080RDB_H
  12
  13 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  14 #define CONFIG_FSL_SATA_V2
  15
  16 /* High Level Configuration Options */
  17 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  18 #define CONFIG_ENABLE_36BIT_PHYS
  19
  20 #ifdef CONFIG_PHYS_64BIT
  21 #define CONFIG_ADDR_MAP 1
  22 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
  23 #endif
  24
  25 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  26 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  27 #define CONFIG_ENV_OVERWRITE
  28
  29 #ifdef CONFIG_RAMBOOT_PBL
  30 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
  31
  32 #define CONFIG_SPL_FLUSH_IMAGE
  33 #define CONFIG_SPL_TEXT_BASE            0xFFFD8000
  34 #define CONFIG_SPL_PAD_TO               0x40000
  35 #define CONFIG_SPL_MAX_SIZE             0x28000
  36 #define RESET_VECTOR_OFFSET             0x27FFC
  37 #define BOOT_PAGE_OFFSET                0x27000
  38 #ifdef CONFIG_SPL_BUILD
  39 #define CONFIG_SPL_SKIP_RELOCATE
  40 #define CONFIG_SPL_COMMON_INIT_DDR
  41 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  42 #endif
  43
  44 #ifdef CONFIG_NAND
  45 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  46 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  47 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  48 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  49 #define CONFIG_SYS_LDSCRIPT  "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
  50 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
  51 #define CONFIG_SPL_NAND_BOOT
  52 #endif
  53
  54 #ifdef CONFIG_SPIFLASH
  55 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  56 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  57 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  58 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  59 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  60 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  61 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
  62 #ifndef CONFIG_SPL_BUILD
  63 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  64 #endif
  65 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
  66 #define CONFIG_SPL_SPI_BOOT
  67 #endif
  68
  69 #ifdef CONFIG_SDCARD
  70 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  71 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  72 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  73 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  74 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  75 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
  76 #ifndef CONFIG_SPL_BUILD
  77 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  78 #endif
  79 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
  80 #define CONFIG_SPL_MMC_BOOT
  81 #endif
  82
  83 #endif /* CONFIG_RAMBOOT_PBL */
  84
  85 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  86 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  87 /* Set 1M boot space */
  88 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  89 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  90                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  91 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  92 #endif
  93
  94 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  95 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  96 #endif
  97
  98 /*
  99  * These can be toggled for performance analysis, otherwise use default.
 100  */
 101 #define CONFIG_SYS_CACHE_STASHING
 102 #define CONFIG_BTB              /* toggle branch predition */
 103 #define CONFIG_DDR_ECC
 104 #ifdef CONFIG_DDR_ECC
 105 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 106 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 107 #endif
 108
 109 #define CONFIG_SYS_MEMTEST_START        0x00200000 /* memtest works on */
 110 #define CONFIG_SYS_MEMTEST_END          0x00400000
 111
 112 #if defined(CONFIG_SPIFLASH)
 113 #define CONFIG_ENV_SPI_BUS      0
 114 #define CONFIG_ENV_SPI_CS       0
 115 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 116 #define CONFIG_ENV_SPI_MODE     0
 117 #define CONFIG_ENV_SIZE         0x2000     /* 8KB */
 118 #define CONFIG_ENV_OFFSET       0x100000   /* 1MB */
 119 #define CONFIG_ENV_SECT_SIZE    0x10000
 120 #elif defined(CONFIG_SDCARD)
 121 #define CONFIG_SYS_MMC_ENV_DEV  0
 122 #define CONFIG_ENV_SIZE         0x2000
 123 #define CONFIG_ENV_OFFSET       (512 * 0x800)
 124 #elif defined(CONFIG_NAND)
 125 #define CONFIG_ENV_SIZE         0x2000
 126 #define CONFIG_ENV_OFFSET       (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
 127 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 128 #define CONFIG_ENV_ADDR         0xffe20000
 129 #define CONFIG_ENV_SIZE         0x2000
 130 #elif defined(CONFIG_ENV_IS_NOWHERE)
 131 #define CONFIG_ENV_SIZE         0x2000
 132 #else
 133 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 134 #define CONFIG_ENV_SIZE         0x2000
 135 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 136 #endif
 137
 138 #ifndef __ASSEMBLY__
 139 unsigned long get_board_sys_clk(void);
 140 unsigned long get_board_ddr_clk(void);
 141 #endif
 142
 143 #define CONFIG_SYS_CLK_FREQ     66660000
 144 #define CONFIG_DDR_CLK_FREQ     133330000
 145
 146 /*
 147  * Config the L3 Cache as L3 SRAM
 148  */
 149 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 150 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 151 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 152 #ifdef CONFIG_RAMBOOT_PBL
 153 #define CONFIG_ENV_ADDR                 (CONFIG_SPL_GD_ADDR + 4 * 1024)
 154 #endif
 155 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 156 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 157 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 158
 159 #define CONFIG_SYS_DCSRBAR      0xf0000000
 160 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 161
 162 /* EEPROM */
 163 #define CONFIG_ID_EEPROM
 164 #define CONFIG_SYS_I2C_EEPROM_NXID
 165 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 166 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 167 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 168
 169 /*
 170  * DDR Setup
 171  */
 172 #define CONFIG_VERY_BIG_RAM
 173 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 174 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 175 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 176 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 177 #define CONFIG_DDR_SPD
 178 #define CONFIG_SYS_SPD_BUS_NUM  0
 179 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 180 #define SPD_EEPROM_ADDRESS1     0x51
 181 #define SPD_EEPROM_ADDRESS2     0x52
 182 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 183 #define CTRL_INTLV_PREFERED     cacheline
 184
 185 /*
 186  * IFC Definitions
 187  */
 188 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 189 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 190 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 191 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 192                                 CSPR_PORT_SIZE_16 | \
 193                                 CSPR_MSEL_NOR | \
 194                                 CSPR_V)
 195 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 196
 197 /* NOR Flash Timing Params */
 198 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 199
 200 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 201                                 FTIM0_NOR_TEADC(0x5) | \
 202                                 FTIM0_NOR_TEAHC(0x5))
 203 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 204                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 205                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 206 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 207                                 FTIM2_NOR_TCH(0x4) | \
 208                                 FTIM2_NOR_TWPH(0x0E) | \
 209                                 FTIM2_NOR_TWP(0x1c))
 210 #define CONFIG_SYS_NOR_FTIM3    0x0
 211
 212 #define CONFIG_SYS_FLASH_QUIET_TEST
 213 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 214
 215 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 216 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 217 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 218 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 219 #define CONFIG_SYS_FLASH_EMPTY_INFO
 220 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 221
 222 /* CPLD on IFC */
 223 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 224 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 225 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 226 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 227                                 | CSPR_PORT_SIZE_8 \
 228                                 | CSPR_MSEL_GPCM \
 229                                 | CSPR_V)
 230 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 231 #define CONFIG_SYS_CSOR2        0x0
 232
 233 /* CPLD Timing parameters for IFC CS2 */
 234 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 235                                         FTIM0_GPCM_TEADC(0x0e) | \
 236                                         FTIM0_GPCM_TEAHC(0x0e))
 237 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 238                                         FTIM1_GPCM_TRAD(0x1f))
 239 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 240                                         FTIM2_GPCM_TCH(0x8) | \
 241                                         FTIM2_GPCM_TWP(0x1f))
 242 #define CONFIG_SYS_CS2_FTIM3            0x0
 243
 244 /* NAND Flash on IFC */
 245 #define CONFIG_NAND_FSL_IFC
 246 #define CONFIG_SYS_NAND_BASE            0xff800000
 247 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 248
 249 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 250 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 251                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 252                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 253                                 | CSPR_V)
 254 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 255
 256 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 257                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 258                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 259                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 260                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 261                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 262                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 263
 264 #define CONFIG_SYS_NAND_ONFI_DETECTION
 265
 266 /* ONFI NAND Flash mode0 Timing Params */
 267 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 268                                         FTIM0_NAND_TWP(0x18)    | \
 269                                         FTIM0_NAND_TWCHT(0x07)  | \
 270                                         FTIM0_NAND_TWH(0x0a))
 271 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 272                                         FTIM1_NAND_TWBE(0x39)   | \
 273                                         FTIM1_NAND_TRR(0x0e)    | \
 274                                         FTIM1_NAND_TRP(0x18))
 275 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 276                                         FTIM2_NAND_TREH(0x0a)   | \
 277                                         FTIM2_NAND_TWHRE(0x1e))
 278 #define CONFIG_SYS_NAND_FTIM3           0x0
 279
 280 #define CONFIG_SYS_NAND_DDR_LAW         11
 281 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 282 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 283 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 284
 285 #if defined(CONFIG_NAND)
 286 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 287 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 288 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 289 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 290 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 291 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 292 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 293 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 294 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 295 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 296 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 297 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 298 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 299 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 300 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 301 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 302 #else
 303 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 304 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 305 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 306 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 307 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 308 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 309 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 310 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 311 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 312 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 313 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 314 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 315 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 316 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 317 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 318 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 319 #endif
 320
 321 #if defined(CONFIG_RAMBOOT_PBL)
 322 #define CONFIG_SYS_RAMBOOT
 323 #endif
 324
 325 #ifdef CONFIG_SPL_BUILD
 326 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 327 #else
 328 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 329 #endif
 330
 331 #define CONFIG_HWCONFIG
 332
 333 /* define to use L1 as initial stack */
 334 #define CONFIG_L1_INIT_RAM
 335 #define CONFIG_SYS_INIT_RAM_LOCK
 336 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 337 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 338 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 339 /* The assembler doesn't like typecast */
 340 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 341                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 342                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 343 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 344 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 345                                                 GENERATED_GBL_DATA_SIZE)
 346 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 347 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 348 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 349
 350 /*
 351  * Serial Port
 352  */
 353 #define CONFIG_SYS_NS16550_SERIAL
 354 #define CONFIG_SYS_NS16550_REG_SIZE     1
 355 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 356 #define CONFIG_SYS_BAUDRATE_TABLE       \
 357         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 358 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 359 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 360 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 361 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 362
 363 /*
 364  * I2C
 365  */
 366 #define CONFIG_SYS_I2C
 367 #define CONFIG_SYS_I2C_FSL
 368 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 369 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 370 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 371 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 372 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 373 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 374 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 375 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 376 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 377 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 378 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 379 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 380 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 381 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 382 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 383 #define I2C_MUX_CH_DEFAULT      0x8
 384
 385 #define I2C_MUX_CH_VOL_MONITOR  0xa
 386
 387 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 388 #ifndef CONFIG_SPL_BUILD
 389 #define CONFIG_VID
 390 #endif
 391 #define CONFIG_VOL_MONITOR_IR36021_SET
 392 #define CONFIG_VOL_MONITOR_IR36021_READ
 393 /* The lowest and highest voltage allowed for T208xRDB */
 394 #define VDD_MV_MIN                      819
 395 #define VDD_MV_MAX                      1212
 396
 397 /*
 398  * RapidIO
 399  */
 400 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 401 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 402 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 403 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 404 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 405 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 406 /*
 407  * for slave u-boot IMAGE instored in master memory space,
 408  * PHYS must be aligned based on the SIZE
 409  */
 410 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 411 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 412 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 413 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 414 /*
 415  * for slave UCODE and ENV instored in master memory space,
 416  * PHYS must be aligned based on the SIZE
 417  */
 418 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 419 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 420 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 421
 422 /* slave core release by master*/
 423 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 424 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 425
 426 /*
 427  * SRIO_PCIE_BOOT - SLAVE
 428  */
 429 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 430 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 431 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 432                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 433 #endif
 434
 435 /*
 436  * eSPI - Enhanced SPI
 437  */
 438
 439 /*
 440  * General PCI
 441  * Memory space is mapped 1-1, but I/O space must start from 0.
 442  */
 443 #define CONFIG_PCIE1            /* PCIE controller 1 */
 444 #define CONFIG_PCIE2            /* PCIE controller 2 */
 445 #define CONFIG_PCIE3            /* PCIE controller 3 */
 446 #define CONFIG_PCIE4            /* PCIE controller 4 */
 447 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 448 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 449 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 450 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 451 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 452 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 453 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 454 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 455 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 456 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 457 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 458
 459 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 460 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 461 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 462 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 463 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 464 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 465 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 466 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 467 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 468
 469 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 470 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 471 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 472 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 473 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 474 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 475 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 476 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 477 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 478
 479 /* controller 4, Base address 203000 */
 480 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 481 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 482 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 483 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 484 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 485 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 486 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 487
 488 #ifdef CONFIG_PCI
 489 #define CONFIG_PCI_INDIRECT_BRIDGE
 490 #define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
 491 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 492 #endif
 493
 494 /* Qman/Bman */
 495 #ifndef CONFIG_NOBQFMAN
 496 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 497 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 498 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 499 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 500 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 501 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 502 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 503 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 504 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 505                                         CONFIG_SYS_BMAN_CENA_SIZE)
 506 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 507 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 508 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 509 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 510 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 511 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 512 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 513 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 514 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 515 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 516 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 517                                         CONFIG_SYS_QMAN_CENA_SIZE)
 518 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 519 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 520
 521 #define CONFIG_SYS_DPAA_FMAN
 522 #define CONFIG_SYS_DPAA_PME
 523 #define CONFIG_SYS_PMAN
 524 #define CONFIG_SYS_DPAA_DCE
 525 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 526 #define CONFIG_SYS_INTERLAKEN
 527
 528 /* Default address of microcode for the Linux Fman driver */
 529 #if defined(CONFIG_SPIFLASH)
 530 /*
 531  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 532  * env, so we got 0x110000.
 533  */
 534 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 535 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
 536 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 537 #define CONFIG_CORTINA_FW_ADDR          0x120000
 538
 539 #elif defined(CONFIG_SDCARD)
 540 /*
 541  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 542  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 543  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 544  */
 545 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 546 #define CONFIG_SYS_CORTINA_FW_IN_MMC
 547 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 548 #define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)
 549
 550 #elif defined(CONFIG_NAND)
 551 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 552 #define CONFIG_SYS_CORTINA_FW_IN_NAND
 553 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 554 #define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 555 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 556 /*
 557  * Slave has no ucode locally, it can fetch this from remote. When implementing
 558  * in two corenet boards, slave's ucode could be stored in master's memory
 559  * space, the address can be mapped from slave TLB->slave LAW->
 560  * slave SRIO or PCIE outbound window->master inbound window->
 561  * master LAW->the ucode address in master's memory space.
 562  */
 563 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 564 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE
 565 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 566 #define CONFIG_CORTINA_FW_ADDR          0xFFE10000
 567 #else
 568 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 569 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 570 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 571 #define CONFIG_CORTINA_FW_ADDR          0xEFE00000
 572 #endif
 573 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 574 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 575 #endif /* CONFIG_NOBQFMAN */
 576
 577 #ifdef CONFIG_SYS_DPAA_FMAN
 578 #define CONFIG_FMAN_ENET
 579 #define CONFIG_PHY_CORTINA
 580 #define CONFIG_PHY_REALTEK
 581 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 582 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 583 #define RGMII_PHY2_ADDR         0x02
 584 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 585 #define CORTINA_PHY_ADDR2       0x0d
 586 #define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
 587 #define FM1_10GEC4_PHY_ADDR     0x01
 588 #endif
 589
 590 #ifdef CONFIG_FMAN_ENET
 591 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 592 #endif
 593
 594 /*
 595  * SATA
 596  */
 597 #ifdef CONFIG_FSL_SATA_V2
 598 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 599 #define CONFIG_SATA1
 600 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 601 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 602 #define CONFIG_SATA2
 603 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 604 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 605 #define CONFIG_LBA48
 606 #endif
 607
 608 /*
 609  * USB
 610  */
 611 #ifdef CONFIG_USB_EHCI_HCD
 612 #define CONFIG_USB_EHCI_FSL
 613 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 614 #define CONFIG_HAS_FSL_DR_USB
 615 #endif
 616
 617 /*
 618  * SDHC
 619  */
 620 #ifdef CONFIG_MMC
 621 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 622 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 623 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 624 #endif
 625
 626 /*
 627  * Dynamic MTD Partition support with mtdparts
 628  */
 629
 630 /*
 631  * Environment
 632  */
 633
 634 /*
 635  * Miscellaneous configurable options
 636  */
 637 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 638
 639 /*
 640  * For booting Linux, the board info and command line data
 641  * have to be in the first 64 MB of memory, since this is
 642  * the maximum mapped by the Linux kernel during initialization.
 643  */
 644 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 645 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 646
 647 #ifdef CONFIG_CMD_KGDB
 648 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 649 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 650 #endif
 651
 652 /*
 653  * Environment Configuration
 654  */
 655 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 656 #define CONFIG_BOOTFILE  "uImage"
 657 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 658
 659 /* default location for tftp and bootm */
 660 #define CONFIG_LOADADDR         1000000
 661 #define __USB_PHY_TYPE          utmi
 662
 663 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 664         "hwconfig=fsl_ddr:"                                     \
 665         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 666         "bank_intlv=auto;"                                      \
 667         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 668         "netdev=eth0\0"                                         \
 669         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 670         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 671         "tftpflash=tftpboot $loadaddr $uboot && "               \
 672         "protect off $ubootaddr +$filesize && "                 \
 673         "erase $ubootaddr +$filesize && "                       \
 674         "cp.b $loadaddr $ubootaddr $filesize && "               \
 675         "protect on $ubootaddr +$filesize && "                  \
 676         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 677         "consoledev=ttyS0\0"                                    \
 678         "ramdiskaddr=2000000\0"                                 \
 679         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 680         "fdtaddr=1e00000\0"                                     \
 681         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 682         "bdev=sda3\0"
 683
 684 /*
 685  * For emulation this causes u-boot to jump to the start of the
 686  * proof point app code automatically
 687  */
 688 #define CONFIG_PROOF_POINTS                             \
 689         "setenv bootargs root=/dev/$bdev rw "           \
 690         "console=$consoledev,$baudrate $othbootargs;"   \
 691         "cpu 1 release 0x29000000 - - -;"               \
 692         "cpu 2 release 0x29000000 - - -;"               \
 693         "cpu 3 release 0x29000000 - - -;"               \
 694         "cpu 4 release 0x29000000 - - -;"               \
 695         "cpu 5 release 0x29000000 - - -;"               \
 696         "cpu 6 release 0x29000000 - - -;"               \
 697         "cpu 7 release 0x29000000 - - -;"               \
 698         "go 0x29000000"
 699
 700 #define CONFIG_HVBOOT                           \
 701         "setenv bootargs config-addr=0x60000000; "      \
 702         "bootm 0x01000000 - 0x00f00000"
 703
 704 #define CONFIG_ALU                              \
 705         "setenv bootargs root=/dev/$bdev rw "           \
 706         "console=$consoledev,$baudrate $othbootargs;"   \
 707         "cpu 1 release 0x01000000 - - -;"               \
 708         "cpu 2 release 0x01000000 - - -;"               \
 709         "cpu 3 release 0x01000000 - - -;"               \
 710         "cpu 4 release 0x01000000 - - -;"               \
 711         "cpu 5 release 0x01000000 - - -;"               \
 712         "cpu 6 release 0x01000000 - - -;"               \
 713         "cpu 7 release 0x01000000 - - -;"               \
 714         "go 0x01000000"
 715
 716 #define CONFIG_LINUX                            \
 717         "setenv bootargs root=/dev/ram rw "             \
 718         "console=$consoledev,$baudrate $othbootargs;"   \
 719         "setenv ramdiskaddr 0x02000000;"                \
 720         "setenv fdtaddr 0x00c00000;"                    \
 721         "setenv loadaddr 0x1000000;"                    \
 722         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 723
 724 #define CONFIG_HDBOOT                                   \
 725         "setenv bootargs root=/dev/$bdev rw "           \
 726         "console=$consoledev,$baudrate $othbootargs;"   \
 727         "tftp $loadaddr $bootfile;"                     \
 728         "tftp $fdtaddr $fdtfile;"                       \
 729         "bootm $loadaddr - $fdtaddr"
 730
 731 #define CONFIG_NFSBOOTCOMMAND                   \
 732         "setenv bootargs root=/dev/nfs rw "     \
 733         "nfsroot=$serverip:$rootpath "          \
 734         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 735         "console=$consoledev,$baudrate $othbootargs;"   \
 736         "tftp $loadaddr $bootfile;"             \
 737         "tftp $fdtaddr $fdtfile;"               \
 738         "bootm $loadaddr - $fdtaddr"
 739
 740 #define CONFIG_RAMBOOTCOMMAND                           \
 741         "setenv bootargs root=/dev/ram rw "             \
 742         "console=$consoledev,$baudrate $othbootargs;"   \
 743         "tftp $ramdiskaddr $ramdiskfile;"               \
 744         "tftp $loadaddr $bootfile;"                     \
 745         "tftp $fdtaddr $fdtfile;"                       \
 746         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 747
 748 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 749
 750 #include <asm/fsl_secure_boot.h>
 751
 752 #endif  /* __T2080RDB_H */