include/configs/MPC8641HPCN.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2006, 2010-2011 Freescale Semiconductor.
   4  *
   5  * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
   6  */
   7
   8 /*
   9  * MPC8641HPCN board configuration file
  10  *
  11  * Make sure you change the MAC address and other network params first,
  12  * search for CONFIG_SERVERIP, etc. in this file.
  13  */
  14
  15 #ifndef __CONFIG_H
  16 #define __CONFIG_H
  17
  18 /* High Level Configuration Options */
  19 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  20 #define CONFIG_ADDR_MAP         1       /* Use addr map */
  21
  22 /*
  23  * default CCSRBAR is at 0xff700000
  24  * assume U-Boot is less than 0.5MB
  25  */
  26
  27 #ifdef RUN_DIAG
  28 #define CONFIG_SYS_DIAG_ADDR         CONFIG_SYS_FLASH_BASE
  29 #endif
  30
  31 /*
  32  * virtual address to be used for temporary mappings.  There
  33  * should be 128k free at this VA.
  34  */
  35 #define CONFIG_SYS_SCRATCH_VA   0xe0000000
  36
  37 #define CONFIG_SYS_SRIO
  38 #define CONFIG_SRIO1                    /* SRIO port 1 */
  39
  40 #define CONFIG_PCIE1            1       /* PCIE controller 1 (ULI bridge) */
  41 #define CONFIG_PCIE2            1       /* PCIE controller 2 (slot) */
  42 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  43 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  44
  45 #define CONFIG_ENV_OVERWRITE
  46
  47 #define CONFIG_BAT_RW           1       /* Use common BAT rw code */
  48 #define CONFIG_HIGH_BATS        1       /* High BATs supported and enabled */
  49 #define CONFIG_SYS_NUM_ADDR_MAP 8       /* Number of addr map slots = 8 dbats */
  50
  51 #define CONFIG_ALTIVEC          1
  52
  53 /*
  54  * L2CR setup -- make sure this is right for your board!
  55  */
  56 #define CONFIG_SYS_L2
  57 #define L2_INIT         0
  58 #define L2_ENABLE       (L2CR_L2E)
  59
  60 #ifndef CONFIG_SYS_CLK_FREQ
  61 #ifndef __ASSEMBLY__
  62 extern unsigned long get_board_sys_clk(unsigned long dummy);
  63 #endif
  64 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
  65 #endif
  66
  67 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  68 #define CONFIG_SYS_MEMTEST_END          0x00400000
  69
  70 /*
  71  * With the exception of PCI Memory and Rapid IO, most devices will simply
  72  * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA
  73  * when 36-bit is enabled.  When 36-bit is not enabled, these bits are 0.
  74  */
  75 #ifdef CONFIG_PHYS_64BIT
  76 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f
  77 #else
  78 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000
  79 #endif
  80
  81 /*
  82  * Base addresses -- Note these are effective addresses where the
  83  * actual resources get mapped (not physical addresses)
  84  */
  85 #define CONFIG_SYS_CCSRBAR              0xffe00000      /* relocated CCSRBAR */
  86 #define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
  87
  88 /* Physical addresses */
  89 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  90 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    CONFIG_SYS_PHYS_ADDR_HIGH
  91 #define CONFIG_SYS_CCSRBAR_PHYS \
  92         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
  93                             CONFIG_SYS_CCSRBAR_PHYS_HIGH)
  94
  95 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */
  96
  97 /*
  98  * DDR Setup
  99  */
 100 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
 101 #define CONFIG_DDR_SPD
 102
 103 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
 104 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
 105
 106 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
 107 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 108 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
 109 #define CONFIG_VERY_BIG_RAM
 110
 111 #define CONFIG_DIMM_SLOTS_PER_CTLR      2
 112 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 113
 114 /*
 115  * I2C addresses of SPD EEPROMs
 116  */
 117 #define SPD_EEPROM_ADDRESS1     0x51    /* CTLR 0 DIMM 0 */
 118 #define SPD_EEPROM_ADDRESS2     0x52    /* CTLR 0 DIMM 1 */
 119 #define SPD_EEPROM_ADDRESS3     0x53    /* CTLR 1 DIMM 0 */
 120 #define SPD_EEPROM_ADDRESS4     0x54    /* CTLR 1 DIMM 1 */
 121
 122 /*
 123  * These are used when DDR doesn't use SPD.
 124  */
 125 #define CONFIG_SYS_SDRAM_SIZE           256             /* DDR is 256MB */
 126 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
 127 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80010102      /* Enable, no interleaving */
 128 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 129 #define CONFIG_SYS_DDR_TIMING_0 0x00260802
 130 #define CONFIG_SYS_DDR_TIMING_1 0x39357322
 131 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
 132 #define CONFIG_SYS_DDR_MODE_1           0x00480432
 133 #define CONFIG_SYS_DDR_MODE_2           0x00000000
 134 #define CONFIG_SYS_DDR_INTERVAL 0x06090100
 135 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 136 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
 137 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
 138 #define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
 139 #define CONFIG_SYS_DDR_CONTROL          0xe3008000      /* Type = DDR2 */
 140 #define CONFIG_SYS_DDR_CONTROL2 0x04400000
 141
 142 #define CONFIG_ID_EEPROM
 143 #define CONFIG_SYS_I2C_EEPROM_NXID
 144 #define CONFIG_ID_EEPROM
 145 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 146 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 147
 148 #define CONFIG_SYS_FLASH_BASE           0xef800000     /* start of FLASH 8M */
 149 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW  CONFIG_SYS_FLASH_BASE
 150 #define CONFIG_SYS_FLASH_BASE_PHYS \
 151         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 152                             CONFIG_SYS_PHYS_ADDR_HIGH)
 153
 154 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
 155
 156 #define CONFIG_SYS_BR0_PRELIM   (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 157                                  | 0x00001001)  /* port size 16bit */
 158 #define CONFIG_SYS_OR0_PRELIM   0xff806ff7      /* 8MB Boot Flash area*/
 159
 160 #define CONFIG_SYS_BR2_PRELIM   (BR_PHYS_ADDR(CF_BASE_PHYS)             \
 161                                  | 0x00001001)  /* port size 16bit */
 162 #define CONFIG_SYS_OR2_PRELIM   0xffffeff7      /* 32k Compact Flash */
 163
 164 #define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(PIXIS_BASE_PHYS)  \
 165                                  | 0x00000801) /* port size 8bit */
 166 #define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32k PIXIS area*/
 167
 168 /*
 169  * The LBC_BASE is the base of the region that contains the PIXIS and the CF.
 170  * The PIXIS and CF by themselves aren't large enough to take up the 128k
 171  * required for the smallest BAT mapping, so there's a 64k hole.
 172  */
 173 #define CONFIG_SYS_LBC_BASE             0xffde0000
 174 #define CONFIG_SYS_LBC_BASE_PHYS_LOW    CONFIG_SYS_LBC_BASE
 175
 176 #define CONFIG_FSL_PIXIS        1       /* use common PIXIS code */
 177 #define PIXIS_BASE              (CONFIG_SYS_LBC_BASE + 0x00010000)
 178 #define PIXIS_BASE_PHYS_LOW     (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000)
 179 #define PIXIS_BASE_PHYS         PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \
 180                                                     CONFIG_SYS_PHYS_ADDR_HIGH)
 181 #define PIXIS_SIZE              0x00008000      /* 32k */
 182 #define PIXIS_ID                0x0     /* Board ID at offset 0 */
 183 #define PIXIS_VER               0x1     /* Board version at offset 1 */
 184 #define PIXIS_PVER              0x2     /* PIXIS FPGA version at offset 2 */
 185 #define PIXIS_RST               0x4     /* PIXIS Reset Control register */
 186 #define PIXIS_AUX               0x6     /* PIXIS Auxiliary register; Scratch register */
 187 #define PIXIS_SPD               0x7     /* Register for SYSCLK speed */
 188 #define PIXIS_VCTL              0x10    /* VELA Control Register */
 189 #define PIXIS_VCFGEN0           0x12    /* VELA Config Enable 0 */
 190 #define PIXIS_VCFGEN1           0x13    /* VELA Config Enable 1 */
 191 #define PIXIS_VBOOT             0x16    /* VELA VBOOT Register */
 192 #define PIXIS_VBOOT_FMAP        0x80    /* VBOOT - CFG_FLASHMAP */
 193 #define PIXIS_VBOOT_FBANK       0x40    /* VBOOT - CFG_FLASHBANK */
 194 #define PIXIS_VSPEED0           0x17    /* VELA VSpeed 0 */
 195 #define PIXIS_VSPEED1           0x18    /* VELA VSpeed 1 */
 196 #define PIXIS_VCLKH             0x19    /* VELA VCLKH register */
 197 #define PIXIS_VCLKL             0x1A    /* VELA VCLKL register */
 198 #define CONFIG_SYS_PIXIS_VBOOT_MASK     0x40    /* Reset altbank mask*/
 199
 200 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */
 201 #define CF_BASE                 (PIXIS_BASE + PIXIS_SIZE)
 202 #define CF_BASE_PHYS            (PIXIS_BASE_PHYS + PIXIS_SIZE)
 203
 204 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 205 #define CONFIG_SYS_MAX_FLASH_SECT       128             /* sectors per device */
 206
 207 #undef  CONFIG_SYS_FLASH_CHECKSUM
 208 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 209 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 210 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE    /* start of monitor */
 211 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 212
 213 #define CONFIG_SYS_FLASH_EMPTY_INFO
 214
 215 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 216 #define CONFIG_SYS_RAMBOOT
 217 #else
 218 #undef  CONFIG_SYS_RAMBOOT
 219 #endif
 220
 221 #if defined(CONFIG_SYS_RAMBOOT)
 222 #undef CONFIG_SPD_EEPROM
 223 #define CONFIG_SYS_SDRAM_SIZE   256
 224 #endif
 225
 226 #undef CONFIG_CLOCKS_IN_MHZ
 227
 228 #define CONFIG_SYS_INIT_RAM_LOCK        1
 229 #ifndef CONFIG_SYS_INIT_RAM_LOCK
 230 #define CONFIG_SYS_INIT_RAM_ADDR        0x0fd00000      /* Initial RAM address */
 231 #else
 232 #define CONFIG_SYS_INIT_RAM_ADDR        0xf8400000      /* Initial RAM address */
 233 #endif
 234 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000          /* Size of used area in RAM */
 235
 236 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 237 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 238
 239 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 kB for Mon */
 240 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)    /* Reserved for malloc */
 241
 242 /* Serial Port */
 243 #define CONFIG_SYS_NS16550_SERIAL
 244 #define CONFIG_SYS_NS16550_REG_SIZE     1
 245 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 246
 247 #define CONFIG_SYS_BAUDRATE_TABLE  \
 248         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 249
 250 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 251 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 252
 253 /*
 254  * I2C
 255  */
 256 #define CONFIG_SYS_I2C
 257 #define CONFIG_SYS_I2C_FSL
 258 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 259 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 260 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3100
 261 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 262
 263 /*
 264  * RapidIO MMU
 265  */
 266 #define CONFIG_SYS_SRIO1_MEM_BASE       0x80000000      /* base address */
 267 #ifdef CONFIG_PHYS_64BIT
 268 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW   0x00000000
 269 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH  0x0000000c
 270 #else
 271 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW   CONFIG_SYS_SRIO1_MEM_BASE
 272 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH  0x00000000
 273 #endif
 274 #define CONFIG_SYS_SRIO1_MEM_PHYS \
 275         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 276                             CONFIG_SYS_SRIO1_MEM_PHYS_HIGH)
 277 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x20000000      /* 128M */
 278
 279 /*
 280  * General PCI
 281  * Addresses are mapped 1-1.
 282  */
 283
 284 #define CONFIG_SYS_PCIE1_NAME           "ULI"
 285 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 286 #ifdef CONFIG_PHYS_64BIT
 287 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 288 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW   0x00000000
 289 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH  0x0000000c
 290 #else
 291 #define CONFIG_SYS_PCIE1_MEM_BUS        CONFIG_SYS_PCIE1_MEM_VIRT
 292 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW   CONFIG_SYS_PCIE1_MEM_VIRT
 293 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH  0x00000000
 294 #endif
 295 #define CONFIG_SYS_PCIE1_MEM_PHYS \
 296         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 297                             CONFIG_SYS_PCIE1_MEM_PHYS_HIGH)
 298 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 299 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 300 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 301 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW    CONFIG_SYS_PCIE1_IO_VIRT
 302 #define CONFIG_SYS_PCIE1_IO_PHYS \
 303         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 304                             CONFIG_SYS_PHYS_ADDR_HIGH)
 305 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64K */
 306
 307 #ifdef CONFIG_PHYS_64BIT
 308 /*
 309  * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT.
 310  * This will increase the amount of PCI address space available for
 311  * for mapping RAM.
 312  */
 313 #define CONFIG_SYS_PCIE2_MEM_BUS        CONFIG_SYS_PCIE1_MEM_BUS
 314 #else
 315 #define CONFIG_SYS_PCIE2_MEM_BUS        (CONFIG_SYS_PCIE1_MEM_BUS \
 316                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 317 #endif
 318 #define CONFIG_SYS_PCIE2_MEM_VIRT       (CONFIG_SYS_PCIE1_MEM_VIRT \
 319                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 320 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW   (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \
 321                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 322 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH  CONFIG_SYS_PCIE1_MEM_PHYS_HIGH
 323 #define CONFIG_SYS_PCIE2_MEM_PHYS       (CONFIG_SYS_PCIE1_MEM_PHYS \
 324                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 325 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 326 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 327 #define CONFIG_SYS_PCIE2_IO_VIRT        (CONFIG_SYS_PCIE1_IO_VIRT \
 328                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 329 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW    (CONFIG_SYS_PCIE1_IO_PHYS_LOW \
 330                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 331 #define CONFIG_SYS_PCIE2_IO_PHYS        (CONFIG_SYS_PCIE1_IO_PHYS \
 332                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 333 #define CONFIG_SYS_PCIE2_IO_SIZE        CONFIG_SYS_PCIE1_IO_SIZE
 334
 335 #if defined(CONFIG_PCI)
 336
 337 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 338
 339 #undef CONFIG_EEPRO100
 340 #undef CONFIG_TULIP
 341
 342 /************************************************************
 343  * USB support
 344  ************************************************************/
 345 #define CONFIG_PCI_OHCI                 1
 346 #define CONFIG_USB_OHCI_NEW             1
 347 #define CONFIG_SYS_USB_OHCI_SLOT_NAME           "ohci_pci"
 348 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15
 349 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
 350
 351 /*PCIE video card used*/
 352 #define VIDEO_IO_OFFSET         CONFIG_SYS_PCIE2_IO_VIRT
 353
 354 /*PCI video card used*/
 355 /*#define VIDEO_IO_OFFSET       CONFIG_SYS_PCIE1_IO_VIRT*/
 356
 357 /* video */
 358
 359 #if defined(CONFIG_VIDEO)
 360 #define CONFIG_BIOSEMU
 361 #define CONFIG_ATI_RADEON_FB
 362 #define CONFIG_VIDEO_LOGO
 363 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT
 364 #endif
 365
 366 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 367
 368 #ifdef CONFIG_SCSI_AHCI
 369 #define CONFIG_SATA_ULI5288
 370 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     4
 371 #define CONFIG_SYS_SCSI_MAX_LUN 1
 372 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
 373 #endif
 374
 375 #endif  /* CONFIG_PCI */
 376
 377 #if defined(CONFIG_TSEC_ENET)
 378 #define CONFIG_TSEC1            1
 379 #define CONFIG_TSEC1_NAME       "eTSEC1"
 380 #define CONFIG_TSEC2            1
 381 #define CONFIG_TSEC2_NAME       "eTSEC2"
 382 #define CONFIG_TSEC3            1
 383 #define CONFIG_TSEC3_NAME       "eTSEC3"
 384 #define CONFIG_TSEC4            1
 385 #define CONFIG_TSEC4_NAME       "eTSEC4"
 386
 387 #define TSEC1_PHY_ADDR          0
 388 #define TSEC2_PHY_ADDR          1
 389 #define TSEC3_PHY_ADDR          2
 390 #define TSEC4_PHY_ADDR          3
 391 #define TSEC1_PHYIDX            0
 392 #define TSEC2_PHYIDX            0
 393 #define TSEC3_PHYIDX            0
 394 #define TSEC4_PHYIDX            0
 395 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 396 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 397 #define TSEC3_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 398 #define TSEC4_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 399
 400 #define CONFIG_ETHPRIME         "eTSEC1"
 401
 402 #endif  /* CONFIG_TSEC_ENET */
 403
 404 #ifdef CONFIG_PHYS_64BIT
 405 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8)
 406 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2)
 407
 408 /* Put physical address into the BAT format */
 409 #define BAT_PHYS_ADDR(low, high) \
 410         (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high))
 411 /* Convert high/low pairs to actual 64-bit value */
 412 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32))
 413 #else
 414 /* 32-bit systems just ignore the "high" bits */
 415 #define BAT_PHYS_ADDR(low, high)        (low)
 416 #define PAIRED_PHYS_TO_PHYS(low, high)  (low)
 417 #endif
 418
 419 /*
 420  * BAT0         DDR
 421  */
 422 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 423 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 424
 425 /*
 426  * BAT1         LBC (PIXIS/CF)
 427  */
 428 #define CONFIG_SYS_DBAT1L       (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \
 429                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 430                                  | BATL_PP_RW | BATL_CACHEINHIBIT | \
 431                                  BATL_GUARDEDSTORAGE)
 432 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_LBC_BASE | BATU_BL_128K \
 433                                  | BATU_VS | BATU_VP)
 434 #define CONFIG_SYS_IBAT1L       (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \
 435                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 436                                  | BATL_PP_RW | BATL_MEMCOHERENCE)
 437 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 438
 439 /* if CONFIG_PCI:
 440  * BAT2         PCIE1 and PCIE1 MEM
 441  * if CONFIG_RIO
 442  * BAT2         Rapidio Memory
 443  */
 444 #ifdef CONFIG_PCI
 445 #define CONFIG_PCI_INDIRECT_BRIDGE
 446 #define CONFIG_SYS_DBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 447                                                CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \
 448                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 449                                  | BATL_GUARDEDSTORAGE)
 450 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \
 451                                  | BATU_VS | BATU_VP)
 452 #define CONFIG_SYS_IBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 453                                                CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \
 454                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 455 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 456 #else /* CONFIG_RIO */
 457 #define CONFIG_SYS_DBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 458                                                CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \
 459                                  | BATL_PP_RW | BATL_CACHEINHIBIT | \
 460                                  BATL_GUARDEDSTORAGE)
 461 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \
 462                                  | BATU_VS | BATU_VP)
 463 #define CONFIG_SYS_IBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 464                                                CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \
 465                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 466 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 467 #endif
 468
 469 /*
 470  * BAT3         CCSR Space
 471  */
 472 #define CONFIG_SYS_DBAT3L       (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 473                                                CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
 474                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 475                                  | BATL_GUARDEDSTORAGE)
 476 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \
 477                                  | BATU_VP)
 478 #define CONFIG_SYS_IBAT3L       (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 479                                                CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
 480                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 481 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 482
 483 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 484 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 485                                        | BATL_PP_RW | BATL_CACHEINHIBIT \
 486                                        | BATL_GUARDEDSTORAGE)
 487 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
 488                                        | BATU_BL_1M | BATU_VS | BATU_VP)
 489 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 490                                        | BATL_PP_RW | BATL_CACHEINHIBIT)
 491 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
 492 #endif
 493
 494 /*
 495  * BAT4         PCIE1_IO and PCIE2_IO
 496  */
 497 #define CONFIG_SYS_DBAT4L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 498                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 499                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 500                                  | BATL_GUARDEDSTORAGE)
 501 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \
 502                                  | BATU_VS | BATU_VP)
 503 #define CONFIG_SYS_IBAT4L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 504                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 505                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 506 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 507
 508 /*
 509  * BAT5         Init RAM for stack in the CPU DCache (no backing memory)
 510  */
 511 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 512 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 513 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 514 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 515
 516 /*
 517  * BAT6         FLASH
 518  */
 519 #define CONFIG_SYS_DBAT6L       (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 520                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 521                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 522                                  | BATL_GUARDEDSTORAGE)
 523 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \
 524                                  | BATU_VP)
 525 #define CONFIG_SYS_IBAT6L       (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 526                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 527                                  | BATL_PP_RW | BATL_MEMCOHERENCE)
 528 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 529
 530 /* Map the last 1M of flash where we're running from reset */
 531 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 532                                  | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 533 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 534 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 535                                  | BATL_MEMCOHERENCE)
 536 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 537
 538 /*
 539  * BAT7         FREE - used later for tmp mappings
 540  */
 541 #define CONFIG_SYS_DBAT7L 0x00000000
 542 #define CONFIG_SYS_DBAT7U 0x00000000
 543 #define CONFIG_SYS_IBAT7L 0x00000000
 544 #define CONFIG_SYS_IBAT7U 0x00000000
 545
 546 /*
 547  * Environment
 548  */
 549 #ifndef CONFIG_SYS_RAMBOOT
 550     #define CONFIG_ENV_ADDR             \
 551                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 552     #define CONFIG_ENV_SECT_SIZE                0x10000 /* 64K(one sector) for env */
 553 #else
 554     #define CONFIG_ENV_ADDR             (CONFIG_SYS_MONITOR_BASE - 0x1000)
 555 #endif
 556 #define CONFIG_ENV_SIZE         0x2000
 557
 558 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 559 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 560
 561 /*
 562  * BOOTP options
 563  */
 564 #define CONFIG_BOOTP_BOOTFILESIZE
 565
 566 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 567
 568 /*
 569  * Miscellaneous configurable options
 570  */
 571 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 572
 573 /*
 574  * For booting Linux, the board info and command line data
 575  * have to be in the first 8 MB of memory, since this is
 576  * the maximum mapped by the Linux kernel during initialization.
 577  */
 578 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Initial Memory map for Linux*/
 579 #define CONFIG_SYS_BOOTM_LEN    (256 << 20)     /* Increase max gunzip size */
 580
 581 #if defined(CONFIG_CMD_KGDB)
 582     #define CONFIG_KGDB_BAUDRATE        230400  /* speed to run kgdb serial port */
 583 #endif
 584
 585 /*
 586  * Environment Configuration
 587  */
 588
 589 #define CONFIG_HAS_ETH0         1
 590 #define CONFIG_HAS_ETH1         1
 591 #define CONFIG_HAS_ETH2         1
 592 #define CONFIG_HAS_ETH3         1
 593
 594 #define CONFIG_IPADDR           192.168.1.100
 595
 596 #define CONFIG_HOSTNAME         "unknown"
 597 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 598 #define CONFIG_BOOTFILE         "uImage"
 599 #define CONFIG_UBOOTPATH        u-boot.bin      /* U-Boot image on TFTP server */
 600
 601 #define CONFIG_SERVERIP         192.168.1.1
 602 #define CONFIG_GATEWAYIP        192.168.1.1
 603 #define CONFIG_NETMASK          255.255.255.0
 604
 605 /* default location for tftp and bootm */
 606 #define CONFIG_LOADADDR         0x10000000
 607
 608 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 609         "netdev=eth0\0"                                                 \
 610         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 611         "tftpflash=tftpboot $loadaddr $uboot; "                         \
 612                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 613                         " +$filesize; " \
 614                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 615                         " +$filesize; " \
 616                 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
 617                         " $filesize; "  \
 618                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 619                         " +$filesize; " \
 620                 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
 621                         " $filesize\0"  \
 622         "consoledev=ttyS0\0"                                            \
 623         "ramdiskaddr=0x18000000\0"                                              \
 624         "ramdiskfile=your.ramdisk.u-boot\0"                             \
 625         "fdtaddr=0x17c00000\0"                                          \
 626         "fdtfile=mpc8641_hpcn.dtb\0"                                    \
 627         "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0"                        \
 628         "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \
 629         "maxcpus=2"
 630
 631 #define CONFIG_NFSBOOTCOMMAND                                           \
 632         "setenv bootargs root=/dev/nfs rw "                             \
 633               "nfsroot=$serverip:$rootpath "                            \
 634               "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 635               "console=$consoledev,$baudrate $othbootargs;"             \
 636         "tftp $loadaddr $bootfile;"                                     \
 637         "tftp $fdtaddr $fdtfile;"                                       \
 638         "bootm $loadaddr - $fdtaddr"
 639
 640 #define CONFIG_RAMBOOTCOMMAND                                           \
 641         "setenv bootargs root=/dev/ram rw "                             \
 642               "console=$consoledev,$baudrate $othbootargs;"             \
 643         "tftp $ramdiskaddr $ramdiskfile;"                               \
 644         "tftp $loadaddr $bootfile;"                                     \
 645         "tftp $fdtaddr $fdtfile;"                                       \
 646         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 647
 648 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 649
 650 #endif  /* __CONFIG_H */