include/configs/MPC832XEMDS.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2006 Freescale Semiconductor, Inc.
   4  */
   5
   6 #ifndef __CONFIG_H
   7 #define __CONFIG_H
   8
   9 /*
  10  * High Level Configuration Options
  11  */
  12 #define CONFIG_E300             1       /* E300 family */
  13 #define CONFIG_QE               1       /* Has QE */
  14
  15 /*
  16  * System IO Config
  17  */
  18 #define CONFIG_SYS_SICRL                0x00000000
  19
  20 /*
  21  * DDR Setup
  22  */
  23 #define CONFIG_SYS_SDRAM_BASE   0x00000000      /* DDR is system memory */
  24 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_SDRAM_BASE
  25 #define CONFIG_SYS_DDRCDR       0x73000002      /* DDR II voltage is 1.8V */
  26
  27 #undef CONFIG_SPD_EEPROM
  28 #if defined(CONFIG_SPD_EEPROM)
  29 /* Determine DDR configuration from I2C interface
  30  */
  31 #define SPD_EEPROM_ADDRESS      0x51    /* DDR SODIMM */
  32 #else
  33 /* Manually set up DDR parameters
  34  */
  35 #define CONFIG_SYS_DDR_SIZE             128     /* MB */
  36 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
  37                                         | CSCONFIG_AP \
  38                                         | CSCONFIG_ODT_WR_CFG \
  39                                         | CSCONFIG_ROW_BIT_13 \
  40                                         | CSCONFIG_COL_BIT_10)
  41                                         /* 0x80840102 */
  42 #define CONFIG_SYS_DDR_TIMING_0         ((0 << TIMING_CFG0_RWT_SHIFT) \
  43                                         | (0 << TIMING_CFG0_WRT_SHIFT) \
  44                                         | (0 << TIMING_CFG0_RRT_SHIFT) \
  45                                         | (0 << TIMING_CFG0_WWT_SHIFT) \
  46                                         | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
  47                                         | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
  48                                         | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
  49                                         | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
  50                                         /* 0x00220802 */
  51 #define CONFIG_SYS_DDR_TIMING_1         ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
  52                                         | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
  53                                         | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
  54                                         | (5 << TIMING_CFG1_CASLAT_SHIFT) \
  55                                         | (13 << TIMING_CFG1_REFREC_SHIFT) \
  56                                         | (3 << TIMING_CFG1_WRREC_SHIFT) \
  57                                         | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
  58                                         | (2 << TIMING_CFG1_WRTORD_SHIFT))
  59                                         /* 0x3935D322 */
  60 #define CONFIG_SYS_DDR_TIMING_2         ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
  61                                 | (31 << TIMING_CFG2_CPO_SHIFT) \
  62                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
  63                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
  64                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
  65                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
  66                                 | (10 << TIMING_CFG2_FOUR_ACT_SHIFT))
  67                                 /* 0x0F9048CA */
  68 #define CONFIG_SYS_DDR_TIMING_3         0x00000000
  69 #define CONFIG_SYS_DDR_CLK_CNTL         DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
  70                                         /* 0x02000000 */
  71 #define CONFIG_SYS_DDR_MODE             ((0x4440 << SDRAM_MODE_ESD_SHIFT) \
  72                                         | (0x0232 << SDRAM_MODE_SD_SHIFT))
  73                                         /* 0x44400232 */
  74 #define CONFIG_SYS_DDR_MODE2            0x8000c000
  75 #define CONFIG_SYS_DDR_INTERVAL         ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \
  76                                         | (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
  77                                         /* 0x03200064 */
  78 #define CONFIG_SYS_DDR_CS0_BNDS         0x00000007
  79 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
  80                                         | SDRAM_CFG_SDRAM_TYPE_DDR2 \
  81                                         | SDRAM_CFG_32_BE)
  82                                         /* 0x43080000 */
  83 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000
  84 #endif
  85
  86 /*
  87  * Memory test
  88  */
  89 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
  90 #define CONFIG_SYS_MEMTEST_START        0x00000000      /* memtest region */
  91 #define CONFIG_SYS_MEMTEST_END          0x00100000
  92
  93 /*
  94  * The reserved memory
  95  */
  96 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  97
  98 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
  99 #define CONFIG_SYS_RAMBOOT
 100 #else
 101 #undef  CONFIG_SYS_RAMBOOT
 102 #endif
 103
 104 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
 105 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024)    /* Reserve 512 kB for Mon */
 106 #define CONFIG_SYS_MALLOC_LEN   (256 * 1024)    /* Reserved for malloc */
 107
 108 /*
 109  * Initial RAM Base Address Setup
 110  */
 111 #define CONFIG_SYS_INIT_RAM_LOCK        1
 112 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000      /* Initial RAM addr */
 113 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in RAM */
 114 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 115                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 116
 117 /*
 118  * Local Bus Configuration & Clock Setup
 119  */
 120 #define CONFIG_SYS_LBC_LBCR             0x00000000
 121
 122 /*
 123  * FLASH on the Local Bus
 124  */
 125 #define CONFIG_SYS_FLASH_BASE   0xFE000000      /* FLASH base address */
 126 #define CONFIG_SYS_FLASH_SIZE   16      /* FLASH size is 16M */
 127
 128
 129 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 130 #define CONFIG_SYS_MAX_FLASH_SECT       128     /* sectors per device */
 131
 132 #undef CONFIG_SYS_FLASH_CHECKSUM
 133
 134 /*
 135  * BCSR on the Local Bus
 136  */
 137 #define CONFIG_SYS_BCSR                 0xF8000000
 138                                         /* Access window base at BCSR base */
 139
 140
 141 /*
 142  * Windows to access PIB via local bus
 143  */
 144                                         /* PIB window base 0xF8008000 */
 145 #define CONFIG_SYS_PIB_BASE             0xF8008000
 146 #define CONFIG_SYS_PIB_WINDOW_SIZE      (32 * 1024)
 147
 148 /*
 149  * CS2 on Local Bus, to PIB
 150  */
 151
 152
 153 /*
 154  * CS3 on Local Bus, to PIB
 155  */
 156
 157
 158 /*
 159  * Serial Port
 160  */
 161 #define CONFIG_SYS_NS16550_SERIAL
 162 #define CONFIG_SYS_NS16550_REG_SIZE     1
 163 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 164
 165 #define CONFIG_SYS_BAUDRATE_TABLE  \
 166                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 167
 168 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 169 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 170
 171 /* I2C */
 172 #define CONFIG_SYS_I2C
 173 #define CONFIG_SYS_I2C_FSL
 174 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 175 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 176 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 177 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 178
 179 /*
 180  * Config on-board RTC
 181  */
 182 #define CONFIG_RTC_DS1374               /* use ds1374 rtc via i2c */
 183 #define CONFIG_SYS_I2C_RTC_ADDR 0x68    /* at address 0x68 */
 184
 185 /*
 186  * General PCI
 187  * Addresses are mapped 1-1.
 188  */
 189 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 190 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 191 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 192 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 193 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 194 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
 195 #define CONFIG_SYS_PCI1_IO_BASE         0x00000000
 196 #define CONFIG_SYS_PCI1_IO_PHYS         0xE0300000
 197 #define CONFIG_SYS_PCI1_IO_SIZE         0x100000        /* 1M */
 198
 199 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL    CONFIG_SYS_SDRAM_BASE
 200 #define CONFIG_SYS_PCI_SLV_MEM_BUS      0x00000000
 201 #define CONFIG_SYS_PCI_SLV_MEM_SIZE     0x80000000
 202
 203 #ifdef CONFIG_PCI
 204 #define CONFIG_PCI_INDIRECT_BRIDGE
 205
 206 #define CONFIG_83XX_PCI_STREAMING
 207
 208 #undef CONFIG_EEPRO100
 209 #undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
 210 #define CONFIG_SYS_PCI_SUBSYS_VENDORID  0x1957  /* Freescale */
 211
 212 #endif  /* CONFIG_PCI */
 213
 214 /*
 215  * QE UEC ethernet configuration
 216  */
 217 #define CONFIG_UEC_ETH
 218 #define CONFIG_ETHPRIME         "UEC0"
 219
 220 #define CONFIG_UEC_ETH1         /* ETH3 */
 221
 222 #ifdef CONFIG_UEC_ETH1
 223 #define CONFIG_SYS_UEC1_UCC_NUM 2       /* UCC3 */
 224 #define CONFIG_SYS_UEC1_RX_CLK          QE_CLK9
 225 #define CONFIG_SYS_UEC1_TX_CLK          QE_CLK10
 226 #define CONFIG_SYS_UEC1_ETH_TYPE        FAST_ETH
 227 #define CONFIG_SYS_UEC1_PHY_ADDR        3
 228 #define CONFIG_SYS_UEC1_INTERFACE_TYPE  PHY_INTERFACE_MODE_MII
 229 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
 230 #endif
 231
 232 #define CONFIG_UEC_ETH2         /* ETH4 */
 233
 234 #ifdef CONFIG_UEC_ETH2
 235 #define CONFIG_SYS_UEC2_UCC_NUM 3       /* UCC4 */
 236 #define CONFIG_SYS_UEC2_RX_CLK          QE_CLK7
 237 #define CONFIG_SYS_UEC2_TX_CLK          QE_CLK8
 238 #define CONFIG_SYS_UEC2_ETH_TYPE        FAST_ETH
 239 #define CONFIG_SYS_UEC2_PHY_ADDR        4
 240 #define CONFIG_SYS_UEC2_INTERFACE_TYPE  PHY_INTERFACE_MODE_MII
 241 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
 242 #endif
 243
 244 /*
 245  * Environment
 246  */
 247 #ifndef CONFIG_SYS_RAMBOOT
 248         #define CONFIG_ENV_ADDR         \
 249                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 250         #define CONFIG_ENV_SECT_SIZE    0x20000
 251         #define CONFIG_ENV_SIZE         0x2000
 252 #else
 253         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 254         #define CONFIG_ENV_SIZE         0x2000
 255 #endif
 256
 257 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 258 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 259
 260 /*
 261  * BOOTP options
 262  */
 263 #define CONFIG_BOOTP_BOOTFILESIZE
 264
 265 /*
 266  * Command line configuration.
 267  */
 268
 269 #undef CONFIG_WATCHDOG          /* watchdog disabled */
 270
 271 /*
 272  * Miscellaneous configurable options
 273  */
 274 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 275
 276 /*
 277  * For booting Linux, the board info and command line data
 278  * have to be in the first 256 MB of memory, since this is
 279  * the maximum mapped by the Linux kernel during initialization.
 280  */
 281                                         /* Initial Memory map for Linux */
 282 #define CONFIG_SYS_BOOTMAPSZ            (256 << 20)
 283 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 284
 285 #if defined(CONFIG_CMD_KGDB)
 286 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 287 #endif
 288
 289 /*
 290  * Environment Configuration
 291  */ #define CONFIG_ENV_OVERWRITE
 292
 293 #if defined(CONFIG_UEC_ETH)
 294 #define CONFIG_HAS_ETH0
 295 #define CONFIG_HAS_ETH1
 296 #endif
 297
 298 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 299
 300 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 301         "netdev=eth0\0"                                                 \
 302         "consoledev=ttyS0\0"                                            \
 303         "ramdiskaddr=1000000\0"                                         \
 304         "ramdiskfile=ramfs.83xx\0"                                      \
 305         "fdtaddr=780000\0"                                              \
 306         "fdtfile=mpc832x_mds.dtb\0"                                     \
 307         ""
 308
 309 #define CONFIG_NFSBOOTCOMMAND                                           \
 310         "setenv bootargs root=/dev/nfs rw "                             \
 311                 "nfsroot=$serverip:$rootpath "                          \
 312                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 313                                                         "$netdev:off "  \
 314                 "console=$consoledev,$baudrate $othbootargs;"           \
 315         "tftp $loadaddr $bootfile;"                                     \
 316         "tftp $fdtaddr $fdtfile;"                                       \
 317         "bootm $loadaddr - $fdtaddr"
 318
 319 #define CONFIG_RAMBOOTCOMMAND                                           \
 320         "setenv bootargs root=/dev/ram rw "                             \
 321                 "console=$consoledev,$baudrate $othbootargs;"           \
 322         "tftp $ramdiskaddr $ramdiskfile;"                               \
 323         "tftp $loadaddr $bootfile;"                                     \
 324         "tftp $fdtaddr $fdtfile;"                                       \
 325         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 326
 327 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
 328
 329 #endif  /* __CONFIG_H */