include/configs/MPC8315ERDB.h

   1 /*
   2  * Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
   3  *
   4  * Dave Liu <daveliu@freescale.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 #define CONFIG_DISPLAY_BOARDINFO
  13
  14 #define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
  15 #define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
  16 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
  17 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
  18 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
  19
  20 #ifndef CONFIG_SYS_TEXT_BASE
  21 #define CONFIG_SYS_TEXT_BASE    0xFE000000
  22 #endif
  23
  24 #ifndef CONFIG_SYS_MONITOR_BASE
  25 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  26 #endif
  27
  28 /*
  29  * High Level Configuration Options
  30  */
  31 #define CONFIG_E300             1 /* E300 family */
  32 #define CONFIG_MPC831x          1 /* MPC831x CPU family */
  33 #define CONFIG_MPC8315          1 /* MPC8315 CPU specific */
  34 #define CONFIG_MPC8315ERDB      1 /* MPC8315ERDB board specific */
  35
  36 /*
  37  * System Clock Setup
  38  */
  39 #define CONFIG_83XX_CLKIN       66666667 /* in Hz */
  40 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
  41
  42 /*
  43  * Hardware Reset Configuration Word
  44  * if CLKIN is 66.66MHz, then
  45  * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
  46  */
  47 #define CONFIG_SYS_HRCW_LOW (\
  48         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  49         HRCWL_DDR_TO_SCB_CLK_2X1 |\
  50         HRCWL_SVCOD_DIV_2 |\
  51         HRCWL_CSB_TO_CLKIN_2X1 |\
  52         HRCWL_CORE_TO_CSB_3X1)
  53 #define CONFIG_SYS_HRCW_HIGH_BASE (\
  54         HRCWH_PCI_HOST |\
  55         HRCWH_PCI1_ARBITER_ENABLE |\
  56         HRCWH_CORE_ENABLE |\
  57         HRCWH_BOOTSEQ_DISABLE |\
  58         HRCWH_SW_WATCHDOG_DISABLE |\
  59         HRCWH_TSEC1M_IN_RGMII |\
  60         HRCWH_TSEC2M_IN_RGMII |\
  61         HRCWH_BIG_ENDIAN |\
  62         HRCWH_LALE_NORMAL)
  63
  64 #ifdef CONFIG_NAND_SPL
  65 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
  66                        HRCWH_FROM_0XFFF00100 |\
  67                        HRCWH_ROM_LOC_NAND_SP_8BIT |\
  68                        HRCWH_RL_EXT_NAND)
  69 #else
  70 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
  71                        HRCWH_FROM_0X00000100 |\
  72                        HRCWH_ROM_LOC_LOCAL_16BIT |\
  73                        HRCWH_RL_EXT_LEGACY)
  74 #endif
  75
  76 /*
  77  * System IO Config
  78  */
  79 #define CONFIG_SYS_SICRH                0x00000000
  80 #define CONFIG_SYS_SICRL                0x00000000 /* 3.3V, no delay */
  81
  82 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
  83 #define CONFIG_HWCONFIG
  84
  85 /*
  86  * IMMR new address
  87  */
  88 #define CONFIG_SYS_IMMR         0xE0000000
  89
  90 /*
  91  * Arbiter Setup
  92  */
  93 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
  94 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
  95 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
  96
  97 /*
  98  * DDR Setup
  99  */
 100 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
 101 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
 102 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
 103 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 104 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 105                                 | DDRCDR_PZ_LOZ \
 106                                 | DDRCDR_NZ_LOZ \
 107                                 | DDRCDR_ODT \
 108                                 | DDRCDR_Q_DRN)
 109                                 /* 0x7b880001 */
 110 /*
 111  * Manually set up DDR parameters
 112  * consist of two chips HY5PS12621BFP-C4 from HYNIX
 113  */
 114 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
 115 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
 116 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 117                                 | CSCONFIG_ODT_RD_NEVER \
 118                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
 119                                 | CSCONFIG_ROW_BIT_13 \
 120                                 | CSCONFIG_COL_BIT_10)
 121                                 /* 0x80010102 */
 122 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 123 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
 124                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
 125                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 126                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 127                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 128                                 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 129                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 130                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 131                                 /* 0x00220802 */
 132 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 133                                 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 134                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 135                                 | (5 << TIMING_CFG1_CASLAT_SHIFT) \
 136                                 | (6 << TIMING_CFG1_REFREC_SHIFT) \
 137                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
 138                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 139                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 140                                 /* 0x27256222 */
 141 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
 142                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
 143                                 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 144                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 145                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 146                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 147                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 148                                 /* 0x121048c5 */
 149 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
 150                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 151                                 /* 0x03600100 */
 152 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 153                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 154                                 | SDRAM_CFG_DBW_32)
 155                                 /* 0x43080000 */
 156 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
 157 #define CONFIG_SYS_DDR_MODE             ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
 158                                 | (0x0232 << SDRAM_MODE_SD_SHIFT))
 159                                 /* ODT 150ohm CL=3, AL=1 on SDRAM */
 160 #define CONFIG_SYS_DDR_MODE2    0x00000000
 161
 162 /*
 163  * Memory test
 164  */
 165 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
 166 #define CONFIG_SYS_MEMTEST_START        0x00040000 /* memtest region */
 167 #define CONFIG_SYS_MEMTEST_END          0x00140000
 168
 169 /*
 170  * The reserved memory
 171  */
 172 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024) /* Reserve 512 kB for Mon */
 173 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 174
 175 /*
 176  * Initial RAM Base Address Setup
 177  */
 178 #define CONFIG_SYS_INIT_RAM_LOCK        1
 179 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 180 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 181 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 182                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 183
 184 /*
 185  * Local Bus Configuration & Clock Setup
 186  */
 187 #define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
 188 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
 189 #define CONFIG_SYS_LBC_LBCR             0x00040000
 190 #define CONFIG_FSL_ELBC         1
 191
 192 /*
 193  * FLASH on the Local Bus
 194  */
 195 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 196 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
 197 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 198
 199 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 200 #define CONFIG_SYS_FLASH_SIZE           8       /* FLASH size is 8M */
 201 #define CONFIG_SYS_FLASH_PROTECTION     1       /* Use h/w Flash protection. */
 202
 203                                         /* Window base at flash base */
 204 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 205 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 206
 207 #define CONFIG_SYS_NOR_BR_PRELIM        (CONFIG_SYS_FLASH_BASE \
 208                                         | BR_PS_16      /* 16 bit port */ \
 209                                         | BR_MS_GPCM    /* MSEL = GPCM */ \
 210                                         | BR_V)         /* valid */
 211 #define CONFIG_SYS_NOR_OR_PRELIM        (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 212                                         | OR_UPM_XAM \
 213                                         | OR_GPCM_CSNT \
 214                                         | OR_GPCM_ACS_DIV2 \
 215                                         | OR_GPCM_XACS \
 216                                         | OR_GPCM_SCY_15 \
 217                                         | OR_GPCM_TRLX_SET \
 218                                         | OR_GPCM_EHTR_SET \
 219                                         | OR_GPCM_EAD)
 220
 221 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 222 /* 127 64KB sectors and 8 8KB top sectors per device */
 223 #define CONFIG_SYS_MAX_FLASH_SECT       135
 224
 225 #undef CONFIG_SYS_FLASH_CHECKSUM
 226 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 227 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 228
 229 /*
 230  * NAND Flash on the Local Bus
 231  */
 232
 233 #ifdef CONFIG_NAND_SPL
 234 #define CONFIG_SYS_NAND_BASE            0xFFF00000
 235 #else
 236 #define CONFIG_SYS_NAND_BASE            0xE0600000
 237 #endif
 238
 239 #define CONFIG_MTD_DEVICE
 240 #define CONFIG_MTD_PARTITION
 241 #define CONFIG_CMD_MTDPARTS
 242 #define MTDIDS_DEFAULT                  "nand0=e0600000.flash"
 243 #define MTDPARTS_DEFAULT                \
 244         "mtdparts=e0600000.flash:512k(uboot),128k(env),6m@1m(kernel),-(fs)"
 245
 246 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 247 #define CONFIG_CMD_NAND                 1
 248 #define CONFIG_NAND_FSL_ELBC            1
 249 #define CONFIG_SYS_NAND_BLOCK_SIZE      16384
 250 #define CONFIG_SYS_NAND_WINDOW_SIZE    (32 * 1024)     /* 0x00008000 */
 251
 252 #define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
 253 #define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
 254 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
 255 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
 256 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
 257
 258 #define CONFIG_SYS_NAND_BR_PRELIM       (CONFIG_SYS_NAND_BASE \
 259                                 | BR_DECC_CHK_GEN       /* Use HW ECC */ \
 260                                 | BR_PS_8               /* 8 bit port */ \
 261                                 | BR_MS_FCM             /* MSEL = FCM */ \
 262                                 | BR_V)                 /* valid */
 263 #define CONFIG_SYS_NAND_OR_PRELIM       \
 264                                 (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
 265                                 | OR_FCM_CSCT \
 266                                 | OR_FCM_CST \
 267                                 | OR_FCM_CHT \
 268                                 | OR_FCM_SCY_1 \
 269                                 | OR_FCM_TRLX \
 270                                 | OR_FCM_EHTR)
 271                                 /* 0xFFFF8396 */
 272
 273 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
 274 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
 275 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
 276 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
 277
 278 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_NAND_BASE
 279 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_32KB)
 280
 281 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
 282 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
 283
 284 #if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
 285         !defined(CONFIG_NAND_SPL)
 286 #define CONFIG_SYS_RAMBOOT
 287 #else
 288 #undef CONFIG_SYS_RAMBOOT
 289 #endif
 290
 291 /*
 292  * Serial Port
 293  */
 294 #define CONFIG_CONS_INDEX       1
 295 #define CONFIG_SYS_NS16550_SERIAL
 296 #define CONFIG_SYS_NS16550_REG_SIZE     1
 297 #define CONFIG_SYS_NS16550_CLK          (CONFIG_83XX_CLKIN * 2)
 298
 299 #define CONFIG_SYS_BAUDRATE_TABLE  \
 300                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 301
 302 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 303 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 304
 305 /* I2C */
 306 #define CONFIG_SYS_I2C
 307 #define CONFIG_SYS_I2C_FSL
 308 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 309 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 310 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 311 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 312
 313 /*
 314  * Board info - revision and where boot from
 315  */
 316 #define CONFIG_SYS_I2C_PCF8574A_ADDR    0x39
 317
 318 /*
 319  * Config on-board RTC
 320  */
 321 #define CONFIG_RTC_DS1337       /* ds1339 on board, use ds1337 rtc via i2c */
 322 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
 323
 324 /*
 325  * General PCI
 326  * Addresses are mapped 1-1.
 327  */
 328 #define CONFIG_SYS_PCI_MEM_BASE         0x80000000
 329 #define CONFIG_SYS_PCI_MEM_PHYS         CONFIG_SYS_PCI_MEM_BASE
 330 #define CONFIG_SYS_PCI_MEM_SIZE         0x10000000 /* 256M */
 331 #define CONFIG_SYS_PCI_MMIO_BASE        0x90000000
 332 #define CONFIG_SYS_PCI_MMIO_PHYS        CONFIG_SYS_PCI_MMIO_BASE
 333 #define CONFIG_SYS_PCI_MMIO_SIZE        0x10000000 /* 256M */
 334 #define CONFIG_SYS_PCI_IO_BASE          0x00000000
 335 #define CONFIG_SYS_PCI_IO_PHYS          0xE0300000
 336 #define CONFIG_SYS_PCI_IO_SIZE          0x100000 /* 1M */
 337
 338 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL    CONFIG_SYS_SDRAM_BASE
 339 #define CONFIG_SYS_PCI_SLV_MEM_BUS      0x00000000
 340 #define CONFIG_SYS_PCI_SLV_MEM_SIZE     0x80000000
 341
 342 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 343 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
 344 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
 345 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 346 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
 347 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
 348 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 349 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
 350 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 351
 352 #define CONFIG_SYS_PCIE2_BASE           0xC0000000
 353 #define CONFIG_SYS_PCIE2_MEM_BASE       0xC0000000
 354 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xC0000000
 355 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000
 356 #define CONFIG_SYS_PCIE2_CFG_BASE       0xD0000000
 357 #define CONFIG_SYS_PCIE2_CFG_SIZE       0x01000000
 358 #define CONFIG_SYS_PCIE2_IO_BASE        0x00000000
 359 #define CONFIG_SYS_PCIE2_IO_PHYS        0xD1000000
 360 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000
 361
 362 #define CONFIG_PCI
 363 #define CONFIG_PCI_INDIRECT_BRIDGE
 364 #define CONFIG_PCIE
 365
 366 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 367
 368 #define CONFIG_EEPRO100
 369 #undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
 370 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 371
 372 #define CONFIG_HAS_FSL_DR_USB
 373 #define CONFIG_SYS_SCCR_USBDRCM         3
 374
 375 #define CONFIG_USB_EHCI
 376 #define CONFIG_USB_EHCI_FSL
 377 #define CONFIG_USB_PHY_TYPE     "utmi"
 378 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 379
 380 /*
 381  * TSEC
 382  */
 383 #define CONFIG_TSEC_ENET        /* TSEC ethernet support */
 384 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 385 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 386 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 387 #define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 388
 389 /*
 390  * TSEC ethernet configuration
 391  */
 392 #define CONFIG_MII              1 /* MII PHY management */
 393 #define CONFIG_TSEC1            1
 394 #define CONFIG_TSEC1_NAME       "eTSEC0"
 395 #define CONFIG_TSEC2            1
 396 #define CONFIG_TSEC2_NAME       "eTSEC1"
 397 #define TSEC1_PHY_ADDR          0
 398 #define TSEC2_PHY_ADDR          1
 399 #define TSEC1_PHYIDX            0
 400 #define TSEC2_PHYIDX            0
 401 #define TSEC1_FLAGS             TSEC_GIGABIT
 402 #define TSEC2_FLAGS             TSEC_GIGABIT
 403
 404 /* Options are: eTSEC[0-1] */
 405 #define CONFIG_ETHPRIME         "eTSEC1"
 406
 407 /*
 408  * SATA
 409  */
 410 #define CONFIG_LIBATA
 411 #define CONFIG_FSL_SATA
 412
 413 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 414 #define CONFIG_SATA1
 415 #define CONFIG_SYS_SATA1_OFFSET 0x18000
 416 #define CONFIG_SYS_SATA1        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
 417 #define CONFIG_SYS_SATA1_FLAGS  FLAGS_DMA
 418 #define CONFIG_SATA2
 419 #define CONFIG_SYS_SATA2_OFFSET 0x19000
 420 #define CONFIG_SYS_SATA2        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
 421 #define CONFIG_SYS_SATA2_FLAGS  FLAGS_DMA
 422
 423 #ifdef CONFIG_FSL_SATA
 424 #define CONFIG_LBA48
 425 #define CONFIG_CMD_SATA
 426 #define CONFIG_DOS_PARTITION
 427 #endif
 428
 429 /*
 430  * Environment
 431  */
 432 #if !defined(CONFIG_SYS_RAMBOOT)
 433         #define CONFIG_ENV_IS_IN_FLASH  1
 434         #define CONFIG_ENV_ADDR         \
 435                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 436         #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 437         #define CONFIG_ENV_SIZE         0x2000
 438 #else
 439         #define CONFIG_SYS_NO_FLASH     1       /* Flash is not usable now */
 440         #define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
 441         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 442         #define CONFIG_ENV_SIZE         0x2000
 443 #endif
 444
 445 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 446 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 447
 448 /*
 449  * BOOTP options
 450  */
 451 #define CONFIG_BOOTP_BOOTFILESIZE
 452 #define CONFIG_BOOTP_BOOTPATH
 453 #define CONFIG_BOOTP_GATEWAY
 454 #define CONFIG_BOOTP_HOSTNAME
 455
 456 /*
 457  * Command line configuration.
 458  */
 459 #define CONFIG_CMD_DATE
 460 #define CONFIG_CMD_PCI
 461
 462 #define CONFIG_CMDLINE_EDITING  1       /* add command line history */
 463 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
 464
 465 #undef CONFIG_WATCHDOG          /* watchdog disabled */
 466
 467 /*
 468  * Miscellaneous configurable options
 469  */
 470 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 471 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 472
 473 #if defined(CONFIG_CMD_KGDB)
 474         #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 475 #else
 476         #define CONFIG_SYS_CBSIZE       256 /* Console I/O Buffer Size */
 477 #endif
 478
 479                                 /* Print Buffer Size */
 480 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 481 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 482                                 /* Boot Argument Buffer Size */
 483 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 484
 485 /*
 486  * For booting Linux, the board info and command line data
 487  * have to be in the first 256 MB of memory, since this is
 488  * the maximum mapped by the Linux kernel during initialization.
 489  */
 490 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 491 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 492
 493 /*
 494  * Core HID Setup
 495  */
 496 #define CONFIG_SYS_HID0_INIT    0x000000000
 497 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 498                                  HID0_ENABLE_INSTRUCTION_CACHE | \
 499                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 500 #define CONFIG_SYS_HID2         HID2_HBE
 501
 502 /*
 503  * MMU Setup
 504  */
 505 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 506
 507 /* DDR: cache cacheable */
 508 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE \
 509                                 | BATL_PP_RW \
 510                                 | BATL_MEMCOHERENCE)
 511 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE \
 512                                 | BATU_BL_128M \
 513                                 | BATU_VS \
 514                                 | BATU_VP)
 515 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 516 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 517
 518 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
 519 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR \
 520                                 | BATL_PP_RW \
 521                                 | BATL_CACHEINHIBIT \
 522                                 | BATL_GUARDEDSTORAGE)
 523 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR \
 524                                 | BATU_BL_8M \
 525                                 | BATU_VS \
 526                                 | BATU_VP)
 527 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 528 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 529
 530 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 531 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE \
 532                                 | BATL_PP_RW \
 533                                 | BATL_MEMCOHERENCE)
 534 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE \
 535                                 | BATU_BL_32M \
 536                                 | BATU_VS \
 537                                 | BATU_VP)
 538 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE \
 539                                 | BATL_PP_RW \
 540                                 | BATL_CACHEINHIBIT \
 541                                 | BATL_GUARDEDSTORAGE)
 542 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 543
 544 /* Stack in dcache: cacheable, no memory coherence */
 545 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 546 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR \
 547                                 | BATU_BL_128K \
 548                                 | BATU_VS \
 549                                 | BATU_VP)
 550 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 551 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 552
 553 /* PCI MEM space: cacheable */
 554 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCI_MEM_PHYS \
 555                                 | BATL_PP_RW \
 556                                 | BATL_MEMCOHERENCE)
 557 #define CONFIG_SYS_IBAT4U       (CONFIG_SYS_PCI_MEM_PHYS \
 558                                 | BATU_BL_256M \
 559                                 | BATU_VS \
 560                                 | BATU_VP)
 561 #define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
 562 #define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U
 563
 564 /* PCI MMIO space: cache-inhibit and guarded */
 565 #define CONFIG_SYS_IBAT5L       (CONFIG_SYS_PCI_MMIO_PHYS \
 566                                 | BATL_PP_RW \
 567                                 | BATL_CACHEINHIBIT \
 568                                 | BATL_GUARDEDSTORAGE)
 569 #define CONFIG_SYS_IBAT5U       (CONFIG_SYS_PCI_MMIO_PHYS \
 570                                 | BATU_BL_256M \
 571                                 | BATU_VS \
 572                                 | BATU_VP)
 573 #define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
 574 #define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U
 575
 576 #define CONFIG_SYS_IBAT6L       0
 577 #define CONFIG_SYS_IBAT6U       0
 578 #define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
 579 #define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
 580
 581 #define CONFIG_SYS_IBAT7L       0
 582 #define CONFIG_SYS_IBAT7U       0
 583 #define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
 584 #define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
 585
 586 #if defined(CONFIG_CMD_KGDB)
 587 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 588 #endif
 589
 590 /*
 591  * Environment Configuration
 592  */
 593
 594 #define CONFIG_ENV_OVERWRITE
 595
 596 #if defined(CONFIG_TSEC_ENET)
 597 #define CONFIG_HAS_ETH0
 598 #define CONFIG_HAS_ETH1
 599 #endif
 600
 601 #define CONFIG_BAUDRATE 115200
 602
 603 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 604
 605 #undef CONFIG_BOOTARGS          /* the boot command will set bootargs */
 606
 607 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 608         "netdev=eth0\0"                                                 \
 609         "consoledev=ttyS0\0"                                            \
 610         "ramdiskaddr=1000000\0"                                         \
 611         "ramdiskfile=ramfs.83xx\0"                                      \
 612         "fdtaddr=780000\0"                                              \
 613         "fdtfile=mpc8315erdb.dtb\0"                                     \
 614         "usb_phy_type=utmi\0"                                           \
 615         ""
 616
 617 #define CONFIG_NFSBOOTCOMMAND                                           \
 618         "setenv bootargs root=/dev/nfs rw "                             \
 619                 "nfsroot=$serverip:$rootpath "                          \
 620                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 621                                                         "$netdev:off "  \
 622                 "console=$consoledev,$baudrate $othbootargs;"           \
 623         "tftp $loadaddr $bootfile;"                                     \
 624         "tftp $fdtaddr $fdtfile;"                                       \
 625         "bootm $loadaddr - $fdtaddr"
 626
 627 #define CONFIG_RAMBOOTCOMMAND                                           \
 628         "setenv bootargs root=/dev/ram rw "                             \
 629                 "console=$consoledev,$baudrate $othbootargs;"           \
 630         "tftp $ramdiskaddr $ramdiskfile;"                               \
 631         "tftp $loadaddr $bootfile;"                                     \
 632         "tftp $fdtaddr $fdtfile;"                                       \
 633         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 634
 635 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
 636
 637 #endif  /* __CONFIG_H */