include/configs/M54418TWR.h

   1 /*
   2  * Configuation settings for the Freescale MCF54418 TWR board.
   3  *
   4  * Copyright 2010-2012 Freescale Semiconductor, Inc.
   5  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 /*
  11  * board/config.h - configuration options, board specific
  12  */
  13
  14 #ifndef _M54418TWR_H
  15 #define _M54418TWR_H
  16
  17 /*
  18  * High Level Configuration Options
  19  * (easy to change)
  20  */
  21
  22 #define CONFIG_MCFUART
  23 #define CONFIG_SYS_UART_PORT            (0)
  24 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600 , 19200 , 38400 , 57600, 115200 }
  25
  26 #define LDS_BOARD_TEXT                  board/freescale/m54418twr/sbf_dram_init.o (.text*)
  27
  28 #undef CONFIG_WATCHDOG
  29
  30 #define CONFIG_TIMESTAMP        /* Print image info with timestamp */
  31
  32 /*
  33  * BOOTP options
  34  */
  35 #define CONFIG_BOOTP_BOOTFILESIZE
  36 #define CONFIG_BOOTP_BOOTPATH
  37 #define CONFIG_BOOTP_GATEWAY
  38 #define CONFIG_BOOTP_HOSTNAME
  39
  40 /*
  41  * NAND FLASH
  42  */
  43 #ifdef CONFIG_CMD_NAND
  44 #define CONFIG_JFFS2_NAND
  45 #define CONFIG_NAND_FSL_NFC
  46 #define CONFIG_SYS_NAND_BASE            0xFC0FC000
  47 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  48 #define NAND_MAX_CHIPS                  CONFIG_SYS_MAX_NAND_DEVICE
  49 #define CONFIG_SYS_NAND_SELECT_DEVICE
  50 #endif
  51
  52 /* Network configuration */
  53 #define CONFIG_MCFFEC
  54 #ifdef CONFIG_MCFFEC
  55 #define CONFIG_MII                      1
  56 #define CONFIG_MII_INIT         1
  57 #define CONFIG_SYS_DISCOVER_PHY
  58 #define CONFIG_SYS_RX_ETH_BUFFER        2
  59 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  60 #define CONFIG_SYS_TX_ETH_BUFFER        2
  61 #define CONFIG_HAS_ETH1
  62
  63 #define CONFIG_SYS_FEC0_PINMUX          0
  64 #define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
  65 #define CONFIG_SYS_FEC1_PINMUX          0
  66 #define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_MIIBASE
  67 #define MCFFEC_TOUT_LOOP                50000
  68 #define CONFIG_SYS_FEC0_PHYADDR 0
  69 #define CONFIG_SYS_FEC1_PHYADDR 1
  70
  71 #define CONFIG_ETHPRIME "FEC0"
  72 #define CONFIG_IPADDR           192.168.1.2
  73 #define CONFIG_NETMASK          255.255.255.0
  74 #define CONFIG_SERVERIP 192.168.1.1
  75 #define CONFIG_GATEWAYIP        192.168.1.1
  76
  77 #define CONFIG_SYS_FEC_BUF_USE_SRAM
  78 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  79 #ifndef CONFIG_SYS_DISCOVER_PHY
  80 #define FECDUPLEX       FULL
  81 #define FECSPEED        _100BASET
  82 #define LINKSTATUS      1
  83 #else
  84 #define LINKSTATUS      0
  85 #ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  86 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  87 #endif
  88 #endif                  /* CONFIG_SYS_DISCOVER_PHY */
  89 #endif
  90
  91 #define CONFIG_HOSTNAME         M54418TWR
  92
  93 #if defined(CONFIG_CF_SBF)
  94 /* ST Micro serial flash */
  95 #define CONFIG_SYS_LOAD_ADDR2           0x40010007
  96 #define CONFIG_EXTRA_ENV_SETTINGS               \
  97         "netdev=eth0\0"                         \
  98         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
  99         "loadaddr=0x40010000\0"                 \
 100         "sbfhdr=sbfhdr.bin\0"                   \
 101         "uboot=u-boot.bin\0"                    \
 102         "load=tftp ${loadaddr} ${sbfhdr};"      \
 103         "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0"       \
 104         "upd=run load; run prog\0"              \
 105         "prog=sf probe 0:1 1000000 3;"          \
 106         "sf erase 0 40000;"                     \
 107         "sf write ${loadaddr} 0 40000;"         \
 108         "save\0"                                \
 109         ""
 110 #elif defined(CONFIG_SYS_NAND_BOOT)
 111 #define CONFIG_EXTRA_ENV_SETTINGS               \
 112         "netdev=eth0\0"                         \
 113         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
 114         "loadaddr=0x40010000\0"                 \
 115         "u-boot=u-boot.bin\0"                   \
 116         "load=tftp ${loadaddr} ${u-boot};\0"    \
 117         "upd=run load; run prog\0"              \
 118         "prog=nand device 0;"                   \
 119         "nand erase 0 40000;"                   \
 120         "nb_update ${loadaddr} ${filesize};"    \
 121         "save\0"                                \
 122         ""
 123 #else
 124 #define CONFIG_SYS_UBOOT_END    0x3FFFF
 125 #define CONFIG_EXTRA_ENV_SETTINGS               \
 126         "netdev=eth0\0"                         \
 127         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
 128         "loadaddr=40010000\0"                   \
 129         "u-boot=u-boot.bin\0"                   \
 130         "load=tftp ${loadaddr) ${u-boot}\0"     \
 131         "upd=run load; run prog\0"              \
 132         "prog=prot off mram" " ;"       \
 133         "cp.b ${loadaddr} 0 ${filesize};"       \
 134         "save\0"                                \
 135         ""
 136 #endif
 137
 138 /* Realtime clock */
 139 #undef CONFIG_MCFRTC
 140 #define CONFIG_RTC_MCFRRTC
 141 #define CONFIG_SYS_MCFRRTC_BASE         0xFC0A8000
 142
 143 /* Timer */
 144 #define CONFIG_MCFTMR
 145 #undef CONFIG_MCFPIT
 146
 147 /* I2c */
 148 #undef CONFIG_SYS_FSL_I2C
 149 #undef  CONFIG_SYS_I2C_SOFT     /* I2C bit-banged */
 150 /* I2C speed and slave address  */
 151 #define CONFIG_SYS_I2C_SPEED            80000
 152 #define CONFIG_SYS_I2C_SLAVE            0x7F
 153 #define CONFIG_SYS_I2C_OFFSET           0x58000
 154 #define CONFIG_SYS_IMMR         CONFIG_SYS_MBAR
 155
 156 /* DSPI and Serial Flash */
 157 #define CONFIG_CF_DSPI
 158 #define CONFIG_SERIAL_FLASH
 159 #define CONFIG_HARD_SPI
 160 #define CONFIG_SYS_SBFHDR_SIZE          0x7
 161 #ifdef CONFIG_CMD_SPI
 162
 163 #       define CONFIG_SYS_DSPI_CTAR0    (DSPI_CTAR_TRSZ(7) | \
 164                                          DSPI_CTAR_PCSSCK_1CLK | \
 165                                          DSPI_CTAR_PASC(0) | \
 166                                          DSPI_CTAR_PDT(0) | \
 167                                          DSPI_CTAR_CSSCK(0) | \
 168                                          DSPI_CTAR_ASC(0) | \
 169                                          DSPI_CTAR_DT(1))
 170 #       define CONFIG_SYS_DSPI_CTAR1    (CONFIG_SYS_DSPI_CTAR0)
 171 #       define CONFIG_SYS_DSPI_CTAR2    (CONFIG_SYS_DSPI_CTAR0)
 172 #endif
 173
 174 /* Input, PCI, Flexbus, and VCO */
 175 #define CONFIG_EXTRA_CLOCK
 176
 177 #define CONFIG_PRAM                     2048    /* 2048 KB */
 178
 179 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 180
 181 #define CONFIG_SYS_LOAD_ADDR            (CONFIG_SYS_SDRAM_BASE + 0x10000)
 182
 183 #define CONFIG_SYS_MBAR         0xFC000000
 184
 185 /*
 186  * Low Level Configuration Settings
 187  * (address mappings, register initial values, etc.)
 188  * You should know what you are doing if you make changes here.
 189  */
 190
 191 /*-----------------------------------------------------------------------
 192  * Definitions for initial stack pointer and data area (in DPRAM)
 193  */
 194 #define CONFIG_SYS_INIT_RAM_ADDR        0x80000000
 195 /* End of used area in internal SRAM */
 196 #define CONFIG_SYS_INIT_RAM_SIZE        0x10000
 197 #define CONFIG_SYS_INIT_RAM_CTRL        0x221
 198 #define CONFIG_SYS_GBL_DATA_OFFSET      ((CONFIG_SYS_INIT_RAM_SIZE - \
 199                                         GENERATED_GBL_DATA_SIZE) - 32)
 200 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 201 #define CONFIG_SYS_SBFHDR_DATA_OFFSET   (CONFIG_SYS_INIT_RAM_SIZE - 32)
 202
 203 /*-----------------------------------------------------------------------
 204  * Start addresses for the final memory configuration
 205  * (Set up by the startup code)
 206  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 207  */
 208 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 209 #define CONFIG_SYS_SDRAM_SIZE           128     /* SDRAM size in MB */
 210
 211 #define CONFIG_SYS_MEMTEST_START        (CONFIG_SYS_SDRAM_BASE + 0x400)
 212 #define CONFIG_SYS_MEMTEST_END          ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
 213 #define CONFIG_SYS_DRAM_TEST
 214
 215 #if defined(CONFIG_CF_SBF) || defined(CONFIG_SYS_NAND_BOOT)
 216 #define CONFIG_SERIAL_BOOT
 217 #endif
 218
 219 #if defined(CONFIG_SERIAL_BOOT)
 220 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400)
 221 #else
 222 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 223 #endif
 224
 225 #define CONFIG_SYS_BOOTPARAMS_LEN       (64 * 1024)
 226 /* Reserve 256 kB for Monitor */
 227 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
 228 /* Reserve 256 kB for malloc() */
 229 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 230
 231 /*
 232  * For booting Linux, the board info and command line data
 233  * have to be in the first 8 MB of memory, since this is
 234  * the maximum mapped by the Linux kernel during initialization ??
 235  */
 236 /* Initial Memory map for Linux */
 237 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \
 238                                 (CONFIG_SYS_SDRAM_SIZE << 20))
 239
 240 /* Configuration for environment
 241  * Environment is embedded in u-boot in the second sector of the flash
 242  */
 243 #if !defined(CONFIG_SERIAL_BOOT)  /*MRAM boot*/
 244 #define CONFIG_ENV_ADDR         (0x40000 - 0x1000) /*MRAM size 40000*/
 245 #define CONFIG_ENV_SIZE         0x1000
 246 #endif
 247
 248 #if defined(CONFIG_CF_SBF)
 249 #define CONFIG_ENV_SPI_CS               1
 250 #define CONFIG_ENV_OFFSET               0x40000
 251 #define CONFIG_ENV_SIZE         0x2000
 252 #define CONFIG_ENV_SECT_SIZE            0x10000
 253 #endif
 254 #if defined(CONFIG_SYS_NAND_BOOT)
 255 #define CONFIG_ENV_OFFSET       0x80000
 256 #define CONFIG_ENV_SIZE 0x20000
 257 #define CONFIG_ENV_SECT_SIZE    0x20000
 258 #endif
 259 #undef CONFIG_ENV_OVERWRITE
 260
 261 /* FLASH organization */
 262 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_CS0_BASE
 263
 264 #undef CONFIG_SYS_FLASH_CFI
 265 #ifdef CONFIG_SYS_FLASH_CFI
 266
 267 #define CONFIG_FLASH_CFI_DRIVER 1
 268 /* Max size that the board might have */
 269 #define CONFIG_SYS_FLASH_SIZE           0x1000000
 270 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 271 /* max number of memory banks */
 272 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 273 /* max number of sectors on one chip */
 274 #define CONFIG_SYS_MAX_FLASH_SECT       270
 275 /* "Real" (hardware) sectors protection */
 276 #define CONFIG_SYS_FLASH_PROTECTION
 277 #define CONFIG_SYS_FLASH_CHECKSUM
 278 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_CS0_BASE }
 279 #else
 280 /* max number of sectors on one chip */
 281 #define CONFIG_SYS_MAX_FLASH_SECT       270
 282 /* max number of sectors on one chip */
 283 #define CONFIG_SYS_MAX_FLASH_BANKS      0
 284 #endif
 285
 286 /*
 287  * This is setting for JFFS2 support in u-boot.
 288  * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
 289  */
 290 #ifdef CONFIG_CMD_JFFS2
 291 #define CONFIG_JFFS2_DEV                "nand0"
 292 #define CONFIG_JFFS2_PART_OFFSET        (0x800000)
 293 #define CONFIG_MTD_DEVICE
 294
 295 #endif
 296
 297 #ifdef CONFIG_CMD_UBI
 298 #define CONFIG_MTD_DEVICE       /* needed for mtdparts command */
 299 #define CONFIG_MTD_PARTITIONS   /* mtdparts and UBI support */
 300 #endif
 301 /* Cache Configuration */
 302 #define CONFIG_SYS_CACHELINE_SIZE       16
 303 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 304                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 305 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 306                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 307 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_BCINVA + CF_CACR_ICINVA)
 308 #define CONFIG_SYS_DCACHE_INV           (CF_CACR_DCINVA)
 309 #define CONFIG_SYS_CACHE_ACR2           (CONFIG_SYS_SDRAM_BASE | \
 310                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 311                                          CF_ACR_EN | CF_ACR_SM_ALL)
 312 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_BEC | CF_CACR_IEC | \
 313                                          CF_CACR_ICINVA | CF_CACR_EUSP)
 314 #define CONFIG_SYS_CACHE_DCACR          ((CONFIG_SYS_CACHE_ICACR | \
 315                                          CF_CACR_DEC | CF_CACR_DDCM_P | \
 316                                          CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
 317
 318 #define CACR_STATUS     (CONFIG_SYS_INIT_RAM_ADDR + \
 319                         CONFIG_SYS_INIT_RAM_SIZE - 12)
 320
 321 /*-----------------------------------------------------------------------
 322  * Memory bank definitions
 323  */
 324 /*
 325  * CS0 - NOR Flash 16MB
 326  * CS1 - Available
 327  * CS2 - Available
 328  * CS3 - Available
 329  * CS4 - Available
 330  * CS5 - Available
 331  */
 332
 333  /* Flash */
 334 #define CONFIG_SYS_CS0_BASE             0x00000000
 335 #define CONFIG_SYS_CS0_MASK             0x000F0101
 336 #define CONFIG_SYS_CS0_CTRL             0x00001D60
 337
 338 #endif                          /* _M54418TWR_H */