include/configs/M54418TWR.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Configuation settings for the Freescale MCF54418 TWR board.
   4  *
   5  * Copyright 2010-2012 Freescale Semiconductor, Inc.
   6  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
   7  */
   8
   9 /*
  10  * board/config.h - configuration options, board specific
  11  */
  12
  13 #ifndef _M54418TWR_H
  14 #define _M54418TWR_H
  15
  16 /*
  17  * High Level Configuration Options
  18  * (easy to change)
  19  */
  20
  21 #define CONFIG_MCFUART
  22 #define CONFIG_SYS_UART_PORT            (0)
  23 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600 , 19200 , 38400 , 57600, 115200 }
  24
  25 #define LDS_BOARD_TEXT                  board/freescale/m54418twr/sbf_dram_init.o (.text*)
  26
  27 #undef CONFIG_WATCHDOG
  28
  29 #define CONFIG_TIMESTAMP        /* Print image info with timestamp */
  30
  31 /*
  32  * BOOTP options
  33  */
  34 #define CONFIG_BOOTP_BOOTFILESIZE
  35
  36 /*
  37  * NAND FLASH
  38  */
  39 #ifdef CONFIG_CMD_NAND
  40 #define CONFIG_JFFS2_NAND
  41 #define CONFIG_NAND_FSL_NFC
  42 #define CONFIG_SYS_NAND_BASE            0xFC0FC000
  43 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  44 #define NAND_MAX_CHIPS                  CONFIG_SYS_MAX_NAND_DEVICE
  45 #define CONFIG_SYS_NAND_SELECT_DEVICE
  46 #endif
  47
  48 /* Network configuration */
  49 #define CONFIG_MCFFEC
  50 #ifdef CONFIG_MCFFEC
  51 #define CONFIG_MII                      1
  52 #define CONFIG_MII_INIT         1
  53 #define CONFIG_SYS_DISCOVER_PHY
  54 #define CONFIG_SYS_RX_ETH_BUFFER        2
  55 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  56 #define CONFIG_SYS_TX_ETH_BUFFER        2
  57 #define CONFIG_HAS_ETH1
  58
  59 #define CONFIG_SYS_FEC0_PINMUX          0
  60 #define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
  61 #define CONFIG_SYS_FEC1_PINMUX          0
  62 #define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_MIIBASE
  63 #define MCFFEC_TOUT_LOOP                50000
  64 #define CONFIG_SYS_FEC0_PHYADDR 0
  65 #define CONFIG_SYS_FEC1_PHYADDR 1
  66
  67 #define CONFIG_ETHPRIME "FEC0"
  68 #define CONFIG_IPADDR           192.168.1.2
  69 #define CONFIG_NETMASK          255.255.255.0
  70 #define CONFIG_SERVERIP 192.168.1.1
  71 #define CONFIG_GATEWAYIP        192.168.1.1
  72
  73 #define CONFIG_SYS_FEC_BUF_USE_SRAM
  74 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  75 #ifndef CONFIG_SYS_DISCOVER_PHY
  76 #define FECDUPLEX       FULL
  77 #define FECSPEED        _100BASET
  78 #define LINKSTATUS      1
  79 #else
  80 #define LINKSTATUS      0
  81 #ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  82 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  83 #endif
  84 #endif                  /* CONFIG_SYS_DISCOVER_PHY */
  85 #endif
  86
  87 #define CONFIG_HOSTNAME         "M54418TWR"
  88
  89 #if defined(CONFIG_CF_SBF)
  90 /* ST Micro serial flash */
  91 #define CONFIG_SYS_LOAD_ADDR2           0x40010007
  92 #define CONFIG_EXTRA_ENV_SETTINGS               \
  93         "netdev=eth0\0"                         \
  94         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
  95         "loadaddr=0x40010000\0"                 \
  96         "sbfhdr=sbfhdr.bin\0"                   \
  97         "uboot=u-boot.bin\0"                    \
  98         "load=tftp ${loadaddr} ${sbfhdr};"      \
  99         "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0"       \
 100         "upd=run load; run prog\0"              \
 101         "prog=sf probe 0:1 1000000 3;"          \
 102         "sf erase 0 40000;"                     \
 103         "sf write ${loadaddr} 0 40000;"         \
 104         "save\0"                                \
 105         ""
 106 #elif defined(CONFIG_SYS_NAND_BOOT)
 107 #define CONFIG_EXTRA_ENV_SETTINGS               \
 108         "netdev=eth0\0"                         \
 109         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
 110         "loadaddr=0x40010000\0"                 \
 111         "u-boot=u-boot.bin\0"                   \
 112         "load=tftp ${loadaddr} ${u-boot};\0"    \
 113         "upd=run load; run prog\0"              \
 114         "prog=nand device 0;"                   \
 115         "nand erase 0 40000;"                   \
 116         "nb_update ${loadaddr} ${filesize};"    \
 117         "save\0"                                \
 118         ""
 119 #else
 120 #define CONFIG_SYS_UBOOT_END    0x3FFFF
 121 #define CONFIG_EXTRA_ENV_SETTINGS               \
 122         "netdev=eth0\0"                         \
 123         "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0"     \
 124         "loadaddr=40010000\0"                   \
 125         "u-boot=u-boot.bin\0"                   \
 126         "load=tftp ${loadaddr) ${u-boot}\0"     \
 127         "upd=run load; run prog\0"              \
 128         "prog=prot off mram" " ;"       \
 129         "cp.b ${loadaddr} 0 ${filesize};"       \
 130         "save\0"                                \
 131         ""
 132 #endif
 133
 134 /* Realtime clock */
 135 #undef CONFIG_MCFRTC
 136 #define CONFIG_RTC_MCFRRTC
 137 #define CONFIG_SYS_MCFRRTC_BASE         0xFC0A8000
 138
 139 /* Timer */
 140 #define CONFIG_MCFTMR
 141 #undef CONFIG_MCFPIT
 142
 143 /* I2c */
 144 #undef CONFIG_SYS_FSL_I2C
 145 #undef  CONFIG_SYS_I2C_SOFT     /* I2C bit-banged */
 146 /* I2C speed and slave address  */
 147 #define CONFIG_SYS_I2C_SPEED            80000
 148 #define CONFIG_SYS_I2C_SLAVE            0x7F
 149 #define CONFIG_SYS_I2C_OFFSET           0x58000
 150 #define CONFIG_SYS_IMMR         CONFIG_SYS_MBAR
 151
 152 /* DSPI and Serial Flash */
 153 #define CONFIG_CF_DSPI
 154 #define CONFIG_SERIAL_FLASH
 155 #define CONFIG_HARD_SPI
 156 #define CONFIG_SYS_SBFHDR_SIZE          0x7
 157 #ifdef CONFIG_CMD_SPI
 158
 159 #       define CONFIG_SYS_DSPI_CTAR0    (DSPI_CTAR_TRSZ(7) | \
 160                                          DSPI_CTAR_PCSSCK_1CLK | \
 161                                          DSPI_CTAR_PASC(0) | \
 162                                          DSPI_CTAR_PDT(0) | \
 163                                          DSPI_CTAR_CSSCK(0) | \
 164                                          DSPI_CTAR_ASC(0) | \
 165                                          DSPI_CTAR_DT(1))
 166 #       define CONFIG_SYS_DSPI_CTAR1    (CONFIG_SYS_DSPI_CTAR0)
 167 #       define CONFIG_SYS_DSPI_CTAR2    (CONFIG_SYS_DSPI_CTAR0)
 168 #endif
 169
 170 /* Input, PCI, Flexbus, and VCO */
 171 #define CONFIG_EXTRA_CLOCK
 172
 173 #define CONFIG_PRAM                     2048    /* 2048 KB */
 174
 175 #define CONFIG_SYS_LOAD_ADDR            (CONFIG_SYS_SDRAM_BASE + 0x10000)
 176
 177 #define CONFIG_SYS_MBAR         0xFC000000
 178
 179 /*
 180  * Low Level Configuration Settings
 181  * (address mappings, register initial values, etc.)
 182  * You should know what you are doing if you make changes here.
 183  */
 184
 185 /*-----------------------------------------------------------------------
 186  * Definitions for initial stack pointer and data area (in DPRAM)
 187  */
 188 #define CONFIG_SYS_INIT_RAM_ADDR        0x80000000
 189 /* End of used area in internal SRAM */
 190 #define CONFIG_SYS_INIT_RAM_SIZE        0x10000
 191 #define CONFIG_SYS_INIT_RAM_CTRL        0x221
 192 #define CONFIG_SYS_GBL_DATA_OFFSET      ((CONFIG_SYS_INIT_RAM_SIZE - \
 193                                         GENERATED_GBL_DATA_SIZE) - 32)
 194 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 195 #define CONFIG_SYS_SBFHDR_DATA_OFFSET   (CONFIG_SYS_INIT_RAM_SIZE - 32)
 196
 197 /*-----------------------------------------------------------------------
 198  * Start addresses for the final memory configuration
 199  * (Set up by the startup code)
 200  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 201  */
 202 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 203 #define CONFIG_SYS_SDRAM_SIZE           128     /* SDRAM size in MB */
 204
 205 #define CONFIG_SYS_MEMTEST_START        (CONFIG_SYS_SDRAM_BASE + 0x400)
 206 #define CONFIG_SYS_MEMTEST_END          ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
 207 #define CONFIG_SYS_DRAM_TEST
 208
 209 #if defined(CONFIG_CF_SBF) || defined(CONFIG_SYS_NAND_BOOT)
 210 #define CONFIG_SERIAL_BOOT
 211 #endif
 212
 213 #if defined(CONFIG_SERIAL_BOOT)
 214 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400)
 215 #else
 216 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 217 #endif
 218
 219 #define CONFIG_SYS_BOOTPARAMS_LEN       (64 * 1024)
 220 /* Reserve 256 kB for Monitor */
 221 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
 222 /* Reserve 256 kB for malloc() */
 223 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 224
 225 /*
 226  * For booting Linux, the board info and command line data
 227  * have to be in the first 8 MB of memory, since this is
 228  * the maximum mapped by the Linux kernel during initialization ??
 229  */
 230 /* Initial Memory map for Linux */
 231 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \
 232                                 (CONFIG_SYS_SDRAM_SIZE << 20))
 233
 234 /* Configuration for environment
 235  * Environment is embedded in u-boot in the second sector of the flash
 236  */
 237 #if !defined(CONFIG_SERIAL_BOOT)  /*MRAM boot*/
 238 #define CONFIG_ENV_ADDR         (0x40000 - 0x1000) /*MRAM size 40000*/
 239 #define CONFIG_ENV_SIZE         0x1000
 240 #endif
 241
 242 #if defined(CONFIG_CF_SBF)
 243 #define CONFIG_ENV_SPI_CS               1
 244 #define CONFIG_ENV_OFFSET               0x40000
 245 #define CONFIG_ENV_SIZE         0x2000
 246 #define CONFIG_ENV_SECT_SIZE            0x10000
 247 #endif
 248 #if defined(CONFIG_SYS_NAND_BOOT)
 249 #define CONFIG_ENV_OFFSET       0x80000
 250 #define CONFIG_ENV_SIZE 0x20000
 251 #define CONFIG_ENV_SECT_SIZE    0x20000
 252 #endif
 253 #undef CONFIG_ENV_OVERWRITE
 254
 255 /* FLASH organization */
 256 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_CS0_BASE
 257
 258 #undef CONFIG_SYS_FLASH_CFI
 259 #ifdef CONFIG_SYS_FLASH_CFI
 260
 261 #define CONFIG_FLASH_CFI_DRIVER 1
 262 /* Max size that the board might have */
 263 #define CONFIG_SYS_FLASH_SIZE           0x1000000
 264 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 265 /* max number of memory banks */
 266 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 267 /* max number of sectors on one chip */
 268 #define CONFIG_SYS_MAX_FLASH_SECT       270
 269 /* "Real" (hardware) sectors protection */
 270 #define CONFIG_SYS_FLASH_PROTECTION
 271 #define CONFIG_SYS_FLASH_CHECKSUM
 272 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_CS0_BASE }
 273 #else
 274 /* max number of sectors on one chip */
 275 #define CONFIG_SYS_MAX_FLASH_SECT       270
 276 /* max number of sectors on one chip */
 277 #define CONFIG_SYS_MAX_FLASH_BANKS      0
 278 #endif
 279
 280 /*
 281  * This is setting for JFFS2 support in u-boot.
 282  * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
 283  */
 284 #ifdef CONFIG_CMD_JFFS2
 285 #define CONFIG_JFFS2_DEV                "nand0"
 286 #define CONFIG_JFFS2_PART_OFFSET        (0x800000)
 287
 288 #endif
 289
 290 /* Cache Configuration */
 291 #define CONFIG_SYS_CACHELINE_SIZE       16
 292 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 293                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 294 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 295                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 296 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_BCINVA + CF_CACR_ICINVA)
 297 #define CONFIG_SYS_DCACHE_INV           (CF_CACR_DCINVA)
 298 #define CONFIG_SYS_CACHE_ACR2           (CONFIG_SYS_SDRAM_BASE | \
 299                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 300                                          CF_ACR_EN | CF_ACR_SM_ALL)
 301 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_BEC | CF_CACR_IEC | \
 302                                          CF_CACR_ICINVA | CF_CACR_EUSP)
 303 #define CONFIG_SYS_CACHE_DCACR          ((CONFIG_SYS_CACHE_ICACR | \
 304                                          CF_CACR_DEC | CF_CACR_DDCM_P | \
 305                                          CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
 306
 307 #define CACR_STATUS     (CONFIG_SYS_INIT_RAM_ADDR + \
 308                         CONFIG_SYS_INIT_RAM_SIZE - 12)
 309
 310 /*-----------------------------------------------------------------------
 311  * Memory bank definitions
 312  */
 313 /*
 314  * CS0 - NOR Flash 16MB
 315  * CS1 - Available
 316  * CS2 - Available
 317  * CS3 - Available
 318  * CS4 - Available
 319  * CS5 - Available
 320  */
 321
 322  /* Flash */
 323 #define CONFIG_SYS_CS0_BASE             0x00000000
 324 #define CONFIG_SYS_CS0_MASK             0x000F0101
 325 #define CONFIG_SYS_CS0_CTRL             0x00001D60
 326
 327 #endif                          /* _M54418TWR_H */