include/configs/BSC9131RDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2011-2012 Freescale Semiconductor, Inc.
   4  */
   5
   6 /*
   7  * BSC9131 RDB board configuration file
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_NAND_FSL_IFC
  14
  15 #ifdef CONFIG_SPIFLASH
  16 #define CONFIG_RAMBOOT_SPIFLASH
  17 #define CONFIG_SYS_RAMBOOT
  18 #define CONFIG_RESET_VECTOR_ADDRESS     0x110bfffc
  19 #endif
  20
  21 #ifdef CONFIG_NAND
  22 #define CONFIG_SPL_INIT_MINIMAL
  23 #define CONFIG_SPL_NAND_BOOT
  24 #define CONFIG_SPL_FLUSH_IMAGE
  25 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  26
  27 #define CONFIG_SPL_MAX_SIZE             8192
  28 #define CONFIG_SPL_RELOC_TEXT_BASE      0x00100000
  29 #define CONFIG_SPL_RELOC_STACK          0x00100000
  30 #define CONFIG_SYS_NAND_U_BOOT_SIZE     ((768 << 10) - 0x2000)
  31 #define CONFIG_SYS_NAND_U_BOOT_DST      (0x00200000 - CONFIG_SPL_MAX_SIZE)
  32 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  33 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0
  34 #define CONFIG_SYS_LDSCRIPT     "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
  35 #endif
  36
  37 #ifdef CONFIG_SPL_BUILD
  38 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
  39 #else
  40 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  41 #endif
  42
  43 /* High Level Configuration Options */
  44
  45 #define CONFIG_ENV_OVERWRITE
  46
  47 #define CONFIG_DDR_CLK_FREQ     66666666 /* DDRCLK on 9131 RDB */
  48 #if defined(CONFIG_SYS_CLK_100)
  49 #define CONFIG_SYS_CLK_FREQ    100000000 /* SYSCLK for 9131 RDB */
  50 #else
  51 #define CONFIG_SYS_CLK_FREQ     66666666 /* SYSCLK for 9131 RDB */
  52 #endif
  53
  54 #define CONFIG_HWCONFIG
  55 /*
  56  * These can be toggled for performance analysis, otherwise use default.
  57  */
  58 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  59 #define CONFIG_BTB                      /* enable branch predition */
  60
  61 #define CONFIG_SYS_MEMTEST_START        0x01000000      /* memtest works on */
  62 #define CONFIG_SYS_MEMTEST_END          0x01ffffff
  63
  64 /* DDR Setup */
  65 #undef CONFIG_SYS_DDR_RAW_TIMING
  66 #undef CONFIG_DDR_SPD
  67 #define CONFIG_SYS_SPD_BUS_NUM          0
  68 #define SPD_EEPROM_ADDRESS              0x52 /* I2C access */
  69
  70 #define CONFIG_MEM_INIT_VALUE           0xDeadBeef
  71
  72 #ifndef __ASSEMBLY__
  73 extern unsigned long get_sdram_size(void);
  74 #endif
  75 #define CONFIG_SYS_SDRAM_SIZE           get_sdram_size() /* DDR size */
  76 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  77 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  78
  79 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  80 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  81
  82 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
  83 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
  84 #define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
  85
  86 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
  87 #define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
  88 #define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
  89 #define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000
  90
  91 #define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
  92 #define CONFIG_SYS_DDR_SR_CNTR          0x00000000
  93 #define CONFIG_SYS_DDR_RCW_1            0x00000000
  94 #define CONFIG_SYS_DDR_RCW_2            0x00000000
  95 #define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3  */
  96 #define CONFIG_SYS_DDR_CONTROL_2        0x24401000
  97 #define CONFIG_SYS_DDR_TIMING_4         0x00000001
  98 #define CONFIG_SYS_DDR_TIMING_5         0x02401400
  99
 100 #define CONFIG_SYS_DDR_TIMING_3_800             0x00030000
 101 #define CONFIG_SYS_DDR_TIMING_0_800             0x00110104
 102 #define CONFIG_SYS_DDR_TIMING_1_800             0x6f6b8644
 103 #define CONFIG_SYS_DDR_TIMING_2_800             0x0fa888cf
 104 #define CONFIG_SYS_DDR_CLK_CTRL_800             0x03000000
 105 #define CONFIG_SYS_DDR_MODE_1_800               0x00441420
 106 #define CONFIG_SYS_DDR_MODE_2_800               0x8000c000
 107 #define CONFIG_SYS_DDR_INTERVAL_800             0x0c300100
 108 #define CONFIG_SYS_DDR_WRLVL_CONTROL_800        0x8675f608
 109
 110 /*
 111  * Base addresses -- Note these are effective addresses where the
 112  * actual resources get mapped (not physical addresses)
 113  */
 114 /* relocated CCSRBAR */
 115 #define CONFIG_SYS_CCSRBAR      CONFIG_SYS_CCSRBAR_DEFAULT
 116 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR_DEFAULT
 117
 118 #define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses */
 119                                                         /* CONFIG_SYS_IMMR */
 120 /* DSP CCSRBAR */
 121 #define CONFIG_SYS_FSL_DSP_CCSRBAR      CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 122 #define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 123
 124 /*
 125  * Memory map
 126  *
 127  * 0x0000_0000  0x3FFF_FFFF     DDR                     1G cacheable
 128  * 0x8800_0000  0x8810_0000     IFC internal SRAM               1M
 129  * 0xB000_0000  0xB0FF_FFFF     DSP core M2 memory      16M
 130  * 0xC100_0000  0xC13F_FFFF     MAPLE-2F                4M
 131  * 0xC1F0_0000  0xC1F3_FFFF     PA L2 SRAM Region 0     256K
 132  * 0xC1F8_0000  0xC1F9_FFFF     PA L2 SRAM Region 1     128K
 133  * 0xFED0_0000  0xFED0_3FFF     SEC Secured RAM         16K
 134  * 0xFF60_0000  0xFF6F_FFFF     DSP CCSR                1M
 135  * 0xFF70_0000  0xFF7F_FFFF     PA CCSR                 1M
 136  * 0xFF80_0000  0xFFFF_FFFF     Boot Page & NAND flash buffer   8M
 137  *
 138  */
 139
 140 /*
 141  * IFC Definitions
 142  */
 143
 144 /* NAND Flash on IFC */
 145 #define CONFIG_SYS_NAND_BASE            0xff800000
 146 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 147
 148 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 149                                 | CSPR_PORT_SIZE_8      /* Port Size = 8 bit*/ \
 150                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 151                                 | CSPR_V)
 152 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 153
 154 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 155                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 156                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 157                                 | CSOR_NAND_RAL_2       /* RAL = 2Byes */ \
 158                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
 159                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */ \
 160                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 161
 162 /* NAND Flash Timing Params */
 163 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x03)  \
 164                                         | FTIM0_NAND_TWP(0x05)   \
 165                                         | FTIM0_NAND_TWCHT(0x02) \
 166                                         | FTIM0_NAND_TWH(0x04))
 167 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x1C) \
 168                                         | FTIM1_NAND_TWBE(0x1E) \
 169                                         | FTIM1_NAND_TRR(0x07)  \
 170                                         | FTIM1_NAND_TRP(0x05))
 171 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x08)  \
 172                                         | FTIM2_NAND_TREH(0x04) \
 173                                         | FTIM2_NAND_TWHRE(0x11))
 174 #define CONFIG_SYS_NAND_FTIM3           FTIM3_NAND_TWW(0x04)
 175
 176 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 177 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 178 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 179
 180 #define CONFIG_SYS_NAND_DDR_LAW         11
 181
 182 /* Set up IFC registers for boot location NAND */
 183 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 184 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 185 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 186 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 187 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 188 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 189 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 190
 191 #define CONFIG_SYS_INIT_RAM_LOCK
 192 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* stack in RAM */
 193 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000/* End of used area in RAM */
 194
 195 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE \
 196                                                 - GENERATED_GBL_DATA_SIZE)
 197 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 198
 199 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 200 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc*/
 201
 202 /* Serial Port */
 203 #undef  CONFIG_SERIAL_SOFTWARE_FIFO
 204 #define CONFIG_SYS_NS16550_SERIAL
 205 #define CONFIG_SYS_NS16550_REG_SIZE     1
 206 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 207 #ifdef CONFIG_SPL_BUILD
 208 #define CONFIG_NS16550_MIN_FUNCTIONS
 209 #endif
 210
 211 #define CONFIG_SYS_BAUDRATE_TABLE       \
 212         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 213
 214 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 215
 216 #define CONFIG_SYS_I2C
 217 #define CONFIG_SYS_I2C_FSL
 218 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 219 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 220 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 221
 222 /* I2C EEPROM */
 223 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 224 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 225 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 226
 227 /* eSPI - Enhanced SPI */
 228
 229 #if defined(CONFIG_TSEC_ENET)
 230
 231 #define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
 232 #define CONFIG_TSEC1    1
 233 #define CONFIG_TSEC1_NAME       "eTSEC1"
 234 #define CONFIG_TSEC2    1
 235 #define CONFIG_TSEC2_NAME       "eTSEC2"
 236
 237 #define TSEC1_PHY_ADDR          0
 238 #define TSEC2_PHY_ADDR          3
 239
 240 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 241 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 242
 243 #define TSEC1_PHYIDX            0
 244
 245 #define TSEC2_PHYIDX            0
 246
 247 #define CONFIG_ETHPRIME         "eTSEC1"
 248
 249 #endif  /* CONFIG_TSEC_ENET */
 250
 251 /*
 252  * Environment
 253  */
 254 #if defined(CONFIG_RAMBOOT_SPIFLASH)
 255 #define CONFIG_ENV_OFFSET       0x100000        /* 1MB */
 256 #define CONFIG_ENV_SECT_SIZE    0x10000
 257 #define CONFIG_ENV_SIZE         0x2000
 258 #elif defined(CONFIG_NAND)
 259 #define CONFIG_ENV_SIZE         CONFIG_SYS_NAND_BLOCK_SIZE
 260 #define CONFIG_ENV_OFFSET       ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
 261 #define CONFIG_ENV_RANGE        (3 * CONFIG_ENV_SIZE)
 262 #elif defined(CONFIG_SYS_RAMBOOT)
 263 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 264 #define CONFIG_ENV_SIZE         0x2000
 265 #endif
 266
 267 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 268 #define CONFIG_SYS_LOADS_BAUD_CHANGE            /* allow baudrate change */
 269
 270 /*
 271  * Miscellaneous configurable options
 272  */
 273 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 274
 275 #if defined(CONFIG_CMD_KGDB)
 276 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 277 #else
 278 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 279 #endif
 280 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 281
 282 /*
 283  * For booting Linux, the board info and command line data
 284  * have to be in the first 64 MB of memory, since this is
 285  * the maximum mapped by the Linux kernel during initialization.
 286  */
 287 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20) /* Initial Memory map for Linux */
 288 #define CONFIG_SYS_BOOTM_LEN    (64 << 20) /* Increase max gunzip size */
 289
 290 #if defined(CONFIG_CMD_KGDB)
 291 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 292 #endif
 293
 294 #ifdef CONFIG_USB_EHCI_HCD
 295 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 296 #define CONFIG_USB_EHCI_FSL
 297 #define CONFIG_HAS_FSL_DR_USB
 298 #endif
 299
 300 /*
 301  * Dynamic MTD Partition support with mtdparts
 302  */
 303
 304 /*
 305  * Environment Configuration
 306  */
 307
 308 #if defined(CONFIG_TSEC_ENET)
 309 #define CONFIG_HAS_ETH0
 310 #endif
 311
 312 #define CONFIG_HOSTNAME         "BSC9131rdb"
 313 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 314 #define CONFIG_BOOTFILE         "uImage"
 315 #define CONFIG_UBOOTPATH        "u-boot.bin" /* U-Boot image on TFTP server */
 316
 317 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 318         "netdev=eth0\0"                                         \
 319         "uboot=" CONFIG_UBOOTPATH "\0"                          \
 320         "loadaddr=1000000\0"                    \
 321         "bootfile=uImage\0"     \
 322         "consoledev=ttyS0\0"                            \
 323         "ramdiskaddr=2000000\0"                 \
 324         "ramdiskfile=rootfs.ext2.gz.uboot\0"            \
 325         "fdtaddr=1e00000\0"                             \
 326         "fdtfile=bsc9131rdb.dtb\0"              \
 327         "bdev=sda1\0"   \
 328         "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"    \
 329         "bootm_size=0x37000000\0"       \
 330         "othbootargs=ramdisk_size=600000 " \
 331         "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \
 332         "usbext2boot=setenv bootargs root=/dev/ram rw " \
 333         "console=$consoledev,$baudrate $othbootargs; "  \
 334         "usb start;"                    \
 335         "ext2load usb 0:4 $loadaddr $bootfile;"         \
 336         "ext2load usb 0:4 $fdtaddr $fdtfile;"   \
 337         "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"   \
 338         "bootm $loadaddr $ramdiskaddr $fdtaddr\0"       \
 339
 340 #define CONFIG_RAMBOOTCOMMAND           \
 341         "setenv bootargs root=/dev/ram rw "     \
 342         "console=$consoledev,$baudrate $othbootargs; "  \
 343         "tftp $ramdiskaddr $ramdiskfile;"       \
 344         "tftp $loadaddr $bootfile;"             \
 345         "tftp $fdtaddr $fdtfile;"               \
 346         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 347
 348 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
 349
 350 #endif  /* __CONFIG_H */